diff options
| -rw-r--r-- | MAINTAINERS | 9 | ||||
| -rw-r--r-- | board/xes/common/Makefile | 4 | ||||
| -rw-r--r-- | board/xes/common/board.c | 64 | ||||
| -rw-r--r-- | board/xes/common/fsl_8xxx_clk.c | 11 | ||||
| -rw-r--r-- | board/xes/common/fsl_8xxx_misc.c | 62 | ||||
| -rw-r--r-- | board/xes/common/fsl_8xxx_misc.h | 28 | ||||
| -rw-r--r-- | board/xes/common/fsl_8xxx_pci.c | 328 | ||||
| -rw-r--r-- | board/xes/xpedite517x/Makefile (renamed from board/xes/xpedite5170/Makefile) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite517x/ddr.c (renamed from board/xes/xpedite5170/ddr.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite517x/law.c (renamed from board/xes/xpedite5170/law.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite517x/xpedite517x.c (renamed from board/xes/xpedite5170/xpedite5170.c) | 20 | ||||
| -rw-r--r-- | board/xes/xpedite520x/Makefile (renamed from board/xes/xpedite5200/Makefile) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite520x/ddr.c (renamed from board/xes/xpedite5200/ddr.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite520x/law.c (renamed from board/xes/xpedite5200/law.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite520x/tlb.c (renamed from board/xes/xpedite5200/tlb.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite520x/xpedite520x.c (renamed from board/xes/xpedite5200/xpedite5200.c) | 27 | ||||
| -rw-r--r-- | board/xes/xpedite537x/Makefile (renamed from board/xes/xpedite5370/Makefile) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite537x/ddr.c (renamed from board/xes/xpedite5370/ddr.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite537x/law.c (renamed from board/xes/xpedite5370/law.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite537x/tlb.c (renamed from board/xes/xpedite5370/tlb.c) | 0 | ||||
| -rw-r--r-- | board/xes/xpedite537x/xpedite537x.c (renamed from board/xes/xpedite5370/xpedite5370.c) | 20 | ||||
| -rw-r--r-- | board/xes/xpedite550x/Makefile | 39 | ||||
| -rw-r--r-- | board/xes/xpedite550x/ddr.c | 165 | ||||
| -rw-r--r-- | board/xes/xpedite550x/law.c | 54 | ||||
| -rw-r--r-- | board/xes/xpedite550x/tlb.c | 98 | ||||
| -rw-r--r-- | board/xes/xpedite550x/xpedite550x.c | 107 | ||||
| -rw-r--r-- | boards.cfg | 9 | ||||
| -rw-r--r-- | common/cmd_pci.c | 13 | ||||
| -rw-r--r-- | doc/README.POST | 19 | ||||
| -rw-r--r-- | drivers/pci/fsl_pci_init.c | 3 | ||||
| -rw-r--r-- | drivers/pci/pci.c | 4 | ||||
| -rw-r--r-- | include/configs/KUP4K.h | 6 | ||||
| -rw-r--r-- | include/configs/KUP4X.h | 6 | ||||
| -rw-r--r-- | include/configs/TB5200.h | 8 | ||||
| -rw-r--r-- | include/configs/TQM5200.h | 8 | ||||
| -rw-r--r-- | include/configs/cm5200.h | 4 | ||||
| -rw-r--r-- | include/configs/corenet_ds.h | 2 | ||||
| -rw-r--r-- | include/configs/lwmon.h | 50 | ||||
| -rw-r--r-- | include/configs/lwmon5.h | 15 | ||||
| -rw-r--r-- | include/configs/spieval.h | 8 | ||||
| -rw-r--r-- | include/configs/xpedite1000.h (renamed from include/configs/XPEDITE1000.h) | 5 | ||||
| -rw-r--r-- | include/configs/xpedite517x.h (renamed from include/configs/XPEDITE5170.h) | 37 | ||||
| -rw-r--r-- | include/configs/xpedite520x.h (renamed from include/configs/XPEDITE5200.h) | 26 | ||||
| -rw-r--r-- | include/configs/xpedite537x.h (renamed from include/configs/XPEDITE5370.h) | 35 | ||||
| -rw-r--r-- | include/configs/xpedite550x.h | 607 | ||||
| -rw-r--r-- | include/post.h | 4 | ||||
| -rw-r--r-- | post/drivers/i2c.c | 99 |
47 files changed, 1524 insertions, 480 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 2f61776..b0da631 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -462,10 +462,11 @@ Rune Torgersen <runet@innovsys.com> Peter Tyser <ptyser@xes-inc.com> - XPEDITE1000 PPC440GX - XPEDITE5170 MPC8640 - XPEDITE5200 MPC8548 - XPEDITE5370 MPC8572 + xpedite1000 PPC440GX + xpedite5170 MPC8640 + xpedite5200 MPC8548 + xpedite5370 MPC8572 + xpedite5500 P2020 David Updegraff <dave@cray.com> diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile index d022831..16e0b66 100644 --- a/board/xes/common/Makefile +++ b/board/xes/common/Makefile @@ -32,7 +32,11 @@ LIB = $(obj)lib$(VENDOR).a COBJS-$(CONFIG_FSL_PCI_INIT) += fsl_8xxx_pci.o COBJS-$(CONFIG_MPC8572) += fsl_8xxx_clk.o COBJS-$(CONFIG_MPC86xx) += fsl_8xxx_clk.o +COBJS-$(CONFIG_P2020) += fsl_8xxx_clk.o COBJS-$(CONFIG_FSL_DDR2) += fsl_8xxx_ddr.o +COBJS-$(CONFIG_FSL_DDR3) += fsl_8xxx_ddr.o +COBJS-$(CONFIG_MPC85xx) += fsl_8xxx_misc.o board.o +COBJS-$(CONFIG_MPC86xx) += fsl_8xxx_misc.o board.o COBJS-$(CONFIG_NAND_ACTL) += actl_nand.o SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) diff --git a/board/xes/common/board.c b/board/xes/common/board.c new file mode 100644 index 0000000..738f0a6 --- /dev/null +++ b/board/xes/common/board.c @@ -0,0 +1,64 @@ +/* + * Copyright 2009 Extreme Engineering Solutions, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include <common.h> +#include "fsl_8xxx_misc.h" + +int checkboard(void) +{ + char name[] = CONFIG_SYS_BOARD_NAME; + char *s; + +#ifdef CONFIG_SYS_FORM_CUSTOM + s = "Custom"; +#elif CONFIG_SYS_FORM_6U_CPCI + s = "6U CompactPCI"; +#elif CONFIG_SYS_FORM_ATCA_PMC + s = "ATCA w/PMC"; +#elif CONFIG_SYS_FORM_ATCA_AMC + s = "ATCA w/AMC"; +#elif CONFIG_SYS_FORM_VME + s = "VME"; +#elif CONFIG_SYS_FORM_6U_VPX + s = "6U VPX"; +#elif CONFIG_SYS_FORM_PMC + s = "PMC"; +#elif CONFIG_SYS_FORM_PCI + s = "PCI"; +#elif CONFIG_SYS_FORM_3U_CPCI + s = "3U CompactPCI"; +#elif CONFIG_SYS_FORM_AMC + s = "AdvancedMC"; +#elif CONFIG_SYS_FORM_XMC + s = "XMC"; +#elif CONFIG_SYS_FORM_PMC_XMC + s = "PMC/XMC"; +#elif CONFIG_SYS_FORM_PCI_EXPRESS + s = "PCI Express"; +#elif CONFIG_SYS_FORM_3U_VPX + s = "3U VPX"; +#else +#error "Form factor not defined" +#endif + + name[strlen(name) - 1] += get_board_derivative(); + printf("Board: X-ES %s %s SBC\n", name, s); + + /* Display board specific information */ + puts(" "); + if ((s = getenv("board_rev"))) + printf("Rev %s, ", s); + if ((s = getenv("serial#"))) + printf("Serial# %s, ", s); + if ((s = getenv("board_cfg"))) + printf("Cfg %s", s); + puts("\n"); + + return 0; +} diff --git a/board/xes/common/fsl_8xxx_clk.c b/board/xes/common/fsl_8xxx_clk.c index f4a17b7..20d0a30 100644 --- a/board/xes/common/fsl_8xxx_clk.c +++ b/board/xes/common/fsl_8xxx_clk.c @@ -38,7 +38,11 @@ unsigned long get_board_sys_clk(ulong dummy) if (in_be32(&gur->gpporcr) & 0x10000) return 66666666; else +#ifdef CONFIG_P2020 + return 100000000; +#else return 50000000; +#endif } #ifdef CONFIG_MPC85xx @@ -54,6 +58,13 @@ unsigned long get_board_ddr_clk(ulong dummy) if (ddr_ratio == 0x7) return get_board_sys_clk(dummy); +#ifdef CONFIG_P2020 + if (in_be32(&gur->gpporcr) & 0x20000) + return 66666666; + else + return 100000000; +#else return 66666666; +#endif } #endif diff --git a/board/xes/common/fsl_8xxx_misc.c b/board/xes/common/fsl_8xxx_misc.c new file mode 100644 index 0000000..b7fa695 --- /dev/null +++ b/board/xes/common/fsl_8xxx_misc.c @@ -0,0 +1,62 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> +#ifdef CONFIG_PCA953X +#include <pca953x.h> + +/* + * Determine if a board's flashes are write protected + */ +int board_flash_wp_on(void) +{ + if (pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_NVM_WP) + return 1; + + return 0; +} +#endif + +/* + * Return a board's derivative model number. For example: + * return 2 for the XPedite5372 and return 1 for the XPedite5201. + */ +uint get_board_derivative(void) +{ +#if defined(CONFIG_MPC85xx) + volatile ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; +#elif defined(CONFIG_MPC86xx) + volatile immap_t *immap = (immap_t *)CONFIG_SYS_CCSRBAR; + volatile ccsr_gur_t *gur = &immap->im_gur; +#endif + + /* + * The top 4 lines of the local bus address are pulled low/high and + * can be read to determine the least significant digit of a board's + * model number. + */ + return gur->gpporcr >> 28; +} + + diff --git a/board/xes/common/fsl_8xxx_misc.h b/board/xes/common/fsl_8xxx_misc.h new file mode 100644 index 0000000..ecc70da --- /dev/null +++ b/board/xes/common/fsl_8xxx_misc.h @@ -0,0 +1,28 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __FSL_8XXX_MISC_H___ +#define __FSL_8XXX_MISC_H___ + +uint get_board_derivative(void); + +#endif /* __FSL_8XXX_MISC_H__ */ diff --git a/board/xes/common/fsl_8xxx_pci.c b/board/xes/common/fsl_8xxx_pci.c index ece7882..f425cee 100644 --- a/board/xes/common/fsl_8xxx_pci.c +++ b/board/xes/common/fsl_8xxx_pci.c @@ -25,10 +25,10 @@ #include <pci.h> #include <asm/fsl_pci.h> #include <asm/io.h> +#include <linux/compiler.h> #include <libfdt.h> #include <fdt_support.h> -int first_free_busno = 0; #ifdef CONFIG_PCI1 static struct pci_controller pci1_hose; @@ -43,111 +43,6 @@ static struct pci_controller pcie2_hose; static struct pci_controller pcie3_hose; #endif -#ifdef CONFIG_MPC8572 -/* Correlate host/agent POR bits to usable info. Table 4-14 */ -struct host_agent_cfg_t { - uchar pcie_root[3]; - uchar rio_host; -} host_agent_cfg[8] = { - {{0, 0, 0}, 0}, - {{0, 1, 1}, 1}, - {{1, 0, 1}, 0}, - {{1, 1, 0}, 1}, - {{0, 0, 1}, 0}, - {{0, 1, 0}, 1}, - {{1, 0, 0}, 0}, - {{1, 1, 1}, 1} -}; - -/* Correlate port width POR bits to usable info. Table 4-15 */ -struct io_port_cfg_t { - uchar pcie_width[3]; - uchar rio_width; -} io_port_cfg[16] = { - {{0, 0, 0}, 0}, - {{0, 0, 0}, 0}, - {{4, 0, 0}, 0}, - {{4, 4, 0}, 0}, - {{0, 0, 0}, 0}, - {{0, 0, 0}, 0}, - {{0, 0, 0}, 4}, - {{4, 2, 2}, 0}, - {{0, 0, 0}, 0}, - {{0, 0, 0}, 0}, - {{0, 0, 0}, 0}, - {{4, 0, 0}, 4}, - {{4, 0, 0}, 4}, - {{0, 0, 0}, 4}, - {{0, 0, 0}, 4}, - {{8, 0, 0}, 0}, -}; -#elif defined CONFIG_MPC8548 -/* Correlate host/agent POR bits to usable info. Table 4-12 */ -struct host_agent_cfg_t { - uchar pci_host[2]; - uchar pcie_root[1]; - uchar rio_host; -} host_agent_cfg[8] = { - {{1, 1}, {0}, 0}, - {{1, 1}, {1}, 0}, - {{1, 1}, {0}, 1}, - {{0, 0}, {0}, 0}, /* reserved */ - {{0, 1}, {1}, 0}, - {{1, 1}, {1}, 0}, - {{0, 1}, {1}, 1}, - {{1, 1}, {1}, 1} -}; - -/* Correlate port width POR bits to usable info. Table 4-13 */ -struct io_port_cfg_t { - uchar pcie_width[1]; - uchar rio_width; -} io_port_cfg[8] = { - {{0}, 0}, - {{0}, 0}, - {{0}, 0}, - {{4}, 4}, - {{4}, 4}, - {{0}, 4}, - {{0}, 4}, - {{8}, 0}, -}; -#elif defined CONFIG_MPC86xx -/* Correlate host/agent POR bits to usable info. Table 4-17 */ -struct host_agent_cfg_t { - uchar pcie_root[2]; - uchar rio_host; -} host_agent_cfg[8] = { - {{0, 0}, 0}, - {{1, 0}, 1}, - {{0, 1}, 0}, - {{1, 1}, 1} -}; - -/* Correlate port width POR bits to usable info. Table 4-16 */ -struct io_port_cfg_t { - uchar pcie_width[2]; - uchar rio_width; -} io_port_cfg[16] = { - {{0, 0}, 0}, - {{0, 0}, 0}, - {{8, 0}, 0}, - {{8, 8}, 0}, - {{0, 0}, 0}, - {{8, 0}, 4}, - {{8, 0}, 4}, - {{8, 0}, 4}, - {{0, 0}, 0}, - {{0, 0}, 4}, - {{0, 0}, 4}, - {{0, 0}, 4}, - {{0, 0}, 0}, - {{0, 0}, 0}, - {{0, 8}, 0}, - {{8, 8}, 0}, -}; -#endif - /* * 85xx and 86xx share naming conventions, but different layout. * Correlate names to CPU-specific values to share common @@ -173,22 +68,22 @@ struct io_port_cfg_t { void pci_init_board(void) { - struct pci_controller *hose; - volatile ccsr_fsl_pci_t *pci; - int width; - int host; + struct fsl_pci_info pci_info[3]; + int first_free_busno = 0; + int num = 0; + int pcie_ep; + __maybe_unused int pcie_configured; + #if defined(CONFIG_MPC85xx) volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); #elif defined(CONFIG_MPC86xx) immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; #endif - uint devdisr = in_be32(&gur->devdisr); - uint io_sel = (in_be32(&gur->pordevsr) & MPC8xxx_PORDEVSR_IO_SEL) >> + u32 devdisr = in_be32(&gur->devdisr); + u32 pordevsr = in_be32(&gur->pordevsr); + __maybe_unused uint io_sel = (pordevsr & MPC8xxx_PORDEVSR_IO_SEL) >> MPC8xxx_PORDEVSR_IO_SEL_SHIFT; - uint host_agent = (in_be32(&gur->porbmsr) & MPC8xxx_PORBMSR_HA) >> - MPC8xxx_PORBMSR_HA_SHIFT; - struct pci_region *r; #ifdef CONFIG_PCI1 uint pci_spd_norm = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1_SPD; @@ -197,49 +92,19 @@ void pci_init_board(void) uint pcix = in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_PCI1; uint freq = CONFIG_SYS_CLK_FREQ / 1000 / 1000; - width = 0; /* Silence compiler warning... */ - io_sel &= 0xf; /* Silence compiler warning... */ - pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR; - hose = &pci1_hose; - host = host_agent_cfg[host_agent].pci_host[0]; - r = hose->regions; - if (!(devdisr & MPC85xx_DEVDISR_PCI1)) { + SET_STD_PCI_INFO(pci_info[num], 1); + pcie_ep = fsl_setup_hose(&pci1_hose, pci_info[num].regs); printf("\n PCI1: %d bit %s, %s %d MHz, %s, %s\n", pci_32 ? 32 : 64, pcix ? "PCIX" : "PCI", pci_spd_norm ? ">=" : "<=", pcix ? freq * 2 : freq, - host ? "host" : "agent", + pcie_ep ? "agent" : "host", pci_arb ? "arbiter" : "external-arbiter"); - /* outbound memory */ - pci_set_region(r++, - CONFIG_SYS_PCI1_MEM_BASE, - CONFIG_SYS_PCI1_MEM_PHYS, - CONFIG_SYS_PCI1_MEM_SIZE, - PCI_REGION_MEM); - - /* outbound io */ - pci_set_region(r++, - CONFIG_SYS_PCI1_IO_BASE, - CONFIG_SYS_PCI1_IO_PHYS, - CONFIG_SYS_PCI1_IO_SIZE, - PCI_REGION_IO); - - hose->region_count = r - hose->regions; - - hose->first_busno = first_free_busno; - - fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data); - - /* Unlock inbound PCI configuration cycles */ - if (!host) - fsl_pci_config_unlock(hose); - - first_free_busno = hose->last_busno + 1; - printf(" PCI1 on bus %02x - %02x\n", - hose->first_busno, hose->last_busno); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pci1_hose, first_free_busno); } else { printf(" PCI1: disabled\n"); } @@ -247,148 +112,53 @@ void pci_init_board(void) /* PCI1 not present on MPC8572 */ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); #endif -#ifdef CONFIG_PCIE1 - pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; - hose = &pcie1_hose; - host = host_agent_cfg[host_agent].pcie_root[0]; - width = io_port_cfg[io_sel].pcie_width[0]; - r = hose->regions; - - if (width && !(devdisr & MPC8xxx_DEVDISR_PCIE1)) { - printf("\n PCIE1 connected as %s (x%d)", - host ? "Root Complex" : "Endpoint", width); - if (in_be32(&pci->pme_msg_det)) { - out_be32(&pci->pme_msg_det, 0xffffffff); - debug(" with errors. Clearing. Now 0x%08x", - in_be32(&pci->pme_msg_det)); - } - printf("\n"); - - /* outbound memory */ - pci_set_region(r++, - CONFIG_SYS_PCIE1_MEM_BASE, - CONFIG_SYS_PCIE1_MEM_PHYS, - CONFIG_SYS_PCIE1_MEM_SIZE, - PCI_REGION_MEM); - - /* outbound io */ - pci_set_region(r++, - CONFIG_SYS_PCIE1_IO_BASE, - CONFIG_SYS_PCIE1_IO_PHYS, - CONFIG_SYS_PCIE1_IO_SIZE, - PCI_REGION_IO); - - hose->region_count = r - hose->regions; - - hose->first_busno = first_free_busno; - - fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data); - /* Unlock inbound PCI configuration cycles */ - if (!host) - fsl_pci_config_unlock(hose); - - first_free_busno = hose->last_busno + 1; - printf(" PCIE1 on bus %02x - %02x\n", - hose->first_busno, hose->last_busno); +#ifdef CONFIG_PCIE1 + pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel); + + if (pcie_configured && !(devdisr & MPC8xxx_DEVDISR_PCIE1)) { + SET_STD_PCIE_INFO(pci_info[num], 1); + pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs); + printf(" PCIE1 connected as %s\n", + pcie_ep ? "Endpoint" : "Root Complex"); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie1_hose, first_free_busno); + } else { + printf(" PCIE1: disabled\n"); } #else setbits_be32(&gur->devdisr, MPC8xxx_DEVDISR_PCIE1); #endif /* CONFIG_PCIE1 */ #ifdef CONFIG_PCIE2 - pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; - hose = &pcie2_hose; - host = host_agent_cfg[host_agent].pcie_root[1]; - width = io_port_cfg[io_sel].pcie_width[1]; - r = hose->regions; - - if (width && !(devdisr & MPC8xxx_DEVDISR_PCIE2)) { - printf("\n PCIE2 connected as %s (x%d)", - host ? "Root Complex" : "Endpoint", width); - if (in_be32(&pci->pme_msg_det)) { - out_be32(&pci->pme_msg_det, 0xffffffff); - debug(" with errors. Clearing. Now 0x%08x", - in_be32(&pci->pme_msg_det)); - } - printf("\n"); - - /* outbound memory */ - pci_set_region(r++, - CONFIG_SYS_PCIE2_MEM_BASE, - CONFIG_SYS_PCIE2_MEM_PHYS, - CONFIG_SYS_PCIE2_MEM_SIZE, - PCI_REGION_MEM); - - /* outbound io */ - pci_set_region(r++, - CONFIG_SYS_PCIE2_IO_BASE, - CONFIG_SYS_PCIE2_IO_PHYS, - CONFIG_SYS_PCIE2_IO_SIZE, - PCI_REGION_IO); - - hose->region_count = r - hose->regions; - - hose->first_busno = first_free_busno; - - fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data); - - /* Unlock inbound PCI configuration cycles */ - if (!host) - fsl_pci_config_unlock(hose); - - first_free_busno = hose->last_busno + 1; - printf(" PCIE2 on bus %02x - %02x\n", - hose->first_busno, hose->last_busno); + pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_2, io_sel); + + if (pcie_configured && !(devdisr & MPC8xxx_DEVDISR_PCIE2)) { + SET_STD_PCIE_INFO(pci_info[num], 2); + pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs); + printf(" PCIE2 connected as %s\n", + pcie_ep ? "Endpoint" : "Root Complex"); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie2_hose, first_free_busno); + } else { + printf(" PCIE2: disabled\n"); } #else setbits_be32(&gur->devdisr, MPC8xxx_DEVDISR_PCIE2); #endif /* CONFIG_PCIE2 */ #ifdef CONFIG_PCIE3 - pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE3_ADDR; - hose = &pcie3_hose; - host = host_agent_cfg[host_agent].pcie_root[2]; - width = io_port_cfg[io_sel].pcie_width[2]; - r = hose->regions; - - if (width && !(devdisr & MPC8xxx_DEVDISR_PCIE3)) { - printf("\n PCIE3 connected as %s (x%d)", - host ? "Root Complex" : "Endpoint", width); - if (in_be32(&pci->pme_msg_det)) { - out_be32(&pci->pme_msg_det, 0xffffffff); - debug(" with errors. Clearing. Now 0x%08x", - in_be32(&pci->pme_msg_det)); - } - printf("\n"); - - /* outbound memory */ - pci_set_region(r++, - CONFIG_SYS_PCIE3_MEM_BASE, - CONFIG_SYS_PCIE3_MEM_PHYS, - CONFIG_SYS_PCIE3_MEM_SIZE, - PCI_REGION_MEM); - - /* outbound io */ - pci_set_region(r++, - CONFIG_SYS_PCIE3_IO_BASE, - CONFIG_SYS_PCIE3_IO_PHYS, - CONFIG_SYS_PCIE3_IO_SIZE, - PCI_REGION_IO); - - hose->region_count = r - hose->regions; - - hose->first_busno = first_free_busno; - - fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data); - - /* Unlock inbound PCI configuration cycles */ - if (!host) - fsl_pci_config_unlock(hose); - - first_free_busno = hose->last_busno + 1; - printf(" PCIE3 on bus %02x - %02x\n", - hose->first_busno, hose->last_busno); + pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_3, io_sel); + + if (pcie_configured && !(devdisr & MPC8xxx_DEVDISR_PCIE3)) { + SET_STD_PCIE_INFO(pci_info[num], 3); + pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info[num].regs); + printf(" PCIE3 connected as %s\n", + pcie_ep ? "Endpoint" : "Root Complex"); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie3_hose, first_free_busno); + } else { + printf(" PCIE3: disabled\n"); } #else setbits_be32(&gur->devdisr, MPC8xxx_DEVDISR_PCIE3); diff --git a/board/xes/xpedite5170/Makefile b/board/xes/xpedite517x/Makefile index fea6686..fea6686 100644 --- a/board/xes/xpedite5170/Makefile +++ b/board/xes/xpedite517x/Makefile diff --git a/board/xes/xpedite5170/ddr.c b/board/xes/xpedite517x/ddr.c index 1d57d09..1d57d09 100644 --- a/board/xes/xpedite5170/ddr.c +++ b/board/xes/xpedite517x/ddr.c diff --git a/board/xes/xpedite5170/law.c b/board/xes/xpedite517x/law.c index 0b7d9ef..0b7d9ef 100644 --- a/board/xes/xpedite5170/law.c +++ b/board/xes/xpedite517x/law.c diff --git a/board/xes/xpedite5170/xpedite5170.c b/board/xes/xpedite517x/xpedite517x.c index 5822941..0f7fa6c 100644 --- a/board/xes/xpedite5170/xpedite5170.c +++ b/board/xes/xpedite517x/xpedite517x.c @@ -26,30 +26,12 @@ #include <asm/io.h> #include <fdt_support.h> #include <pca953x.h> +#include "../common/fsl_8xxx_misc.h" #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_PCI) extern void ft_board_pci_setup(void *blob, bd_t *bd); #endif -int checkboard(void) -{ - char *s; - - printf("Board: X-ES %s 3U VPX SBC\n", CONFIG_SYS_BOARD_NAME); - printf(" "); - s = getenv("board_rev"); - if (s) - printf("Rev %s, ", s); - s = getenv("serial#"); - if (s) - printf("Serial# %s, ", s); - s = getenv("board_cfg"); - if (s) - printf("Cfg %s", s); - printf("\n"); - - return 0; -} /* * Print out which flash was booted from and if booting from the 2nd flash, * swap flash chip selects to maintain consistent flash numbering/addresses. diff --git a/board/xes/xpedite5200/Makefile b/board/xes/xpedite520x/Makefile index 02fe8fc..02fe8fc 100644 --- a/board/xes/xpedite5200/Makefile +++ b/board/xes/xpedite520x/Makefile diff --git a/board/xes/xpedite5200/ddr.c b/board/xes/xpedite520x/ddr.c index c5616d5..c5616d5 100644 --- a/board/xes/xpedite5200/ddr.c +++ b/board/xes/xpedite520x/ddr.c diff --git a/board/xes/xpedite5200/law.c b/board/xes/xpedite520x/law.c index bbfcb9d..bbfcb9d 100644 --- a/board/xes/xpedite5200/law.c +++ b/board/xes/xpedite520x/law.c diff --git a/board/xes/xpedite5200/tlb.c b/board/xes/xpedite520x/tlb.c index bd7bff8..bd7bff8 100644 --- a/board/xes/xpedite5200/tlb.c +++ b/board/xes/xpedite520x/tlb.c diff --git a/board/xes/xpedite5200/xpedite5200.c b/board/xes/xpedite520x/xpedite520x.c index a2627f8..dc5c965 100644 --- a/board/xes/xpedite5200/xpedite5200.c +++ b/board/xes/xpedite520x/xpedite520x.c @@ -36,33 +36,6 @@ extern void ft_board_pci_setup(void *blob, bd_t *bd); -int checkboard(void) -{ - volatile fsl_lbc_t *lbc = LBC_BASE_ADDR; - volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR); - char *s; - - printf("Board: X-ES %s PMC\n", CONFIG_SYS_BOARD_NAME); - printf(" "); - s = getenv("board_rev"); - if (s) - printf("Rev %s, ", s); - s = getenv("serial#"); - if (s) - printf("Serial# %s, ", s); - s = getenv("board_cfg"); - if (s) - printf("Cfg %s", s); - printf("\n"); - - out_be32(&lbc->ltesr, 0xffffffff); /* Clear LBC error IRQs */ - out_be32(&lbc->lteir, 0xffffffff); /* Enable LBC error IRQs */ - out_be32(&ecm->eedr, 0xffffffff); /* Clear ecm errors */ - out_be32(&ecm->eeer, 0xffffffff); /* Enable ecm errors */ - - return 0; -} - static void flash_cs_fixup(void) { int flash_sel; diff --git a/board/xes/xpedite5370/Makefile b/board/xes/xpedite537x/Makefile index 919397c..919397c 100644 --- a/board/xes/xpedite5370/Makefile +++ b/board/xes/xpedite537x/Makefile diff --git a/board/xes/xpedite5370/ddr.c b/board/xes/xpedite537x/ddr.c index 4d3f255..4d3f255 100644 --- a/board/xes/xpedite5370/ddr.c +++ b/board/xes/xpedite537x/ddr.c diff --git a/board/xes/xpedite5370/law.c b/board/xes/xpedite537x/law.c index daee676..daee676 100644 --- a/board/xes/xpedite5370/law.c +++ b/board/xes/xpedite537x/law.c diff --git a/board/xes/xpedite5370/tlb.c b/board/xes/xpedite537x/tlb.c index a465ce3..a465ce3 100644 --- a/board/xes/xpedite5370/tlb.c +++ b/board/xes/xpedite537x/tlb.c diff --git a/board/xes/xpedite5370/xpedite5370.c b/board/xes/xpedite537x/xpedite537x.c index 2a060c2..89fa6c7 100644 --- a/board/xes/xpedite5370/xpedite5370.c +++ b/board/xes/xpedite537x/xpedite537x.c @@ -36,26 +36,6 @@ DECLARE_GLOBAL_DATA_PTR; extern void ft_board_pci_setup(void *blob, bd_t *bd); -int checkboard(void) -{ - char *s; - - printf("Board: X-ES %s 3U VPX SBC\n", CONFIG_SYS_BOARD_NAME); - printf(" "); - s = getenv("board_rev"); - if (s) - printf("Rev %s, ", s); - s = getenv("serial#"); - if (s) - printf("Serial# %s, ", s); - s = getenv("board_cfg"); - if (s) - printf("Cfg %s", s); - printf("\n"); - - return 0; -} - static void flash_cs_fixup(void) { int flash_sel; diff --git a/board/xes/xpedite550x/Makefile b/board/xes/xpedite550x/Makefile new file mode 100644 index 0000000..8980a4b --- /dev/null +++ b/board/xes/xpedite550x/Makefile @@ -0,0 +1,39 @@ +# +# Copyright 2007-2008 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS-y)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xes/xpedite550x/ddr.c b/board/xes/xpedite550x/ddr.c new file mode 100644 index 0000000..718cd98 --- /dev/null +++ b/board/xes/xpedite550x/ddr.c @@ -0,0 +1,165 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <i2c.h> + +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> + +static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr3_spd_eeprom_t)); +} + +void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num) +{ + unsigned int i; + unsigned int i2c_address = 0; + + for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) { + if (ctrl_num == 0 && i == 0) + i2c_address = SPD_EEPROM_ADDRESS1; + get_spd(&(ctrl_dimms_spd[i]), i2c_address); + } +} + +unsigned int fsl_ddr_get_mem_data_rate(void) +{ + return get_ddr_freq(0); +} + +/* + * There are traditionally three board-specific SDRAM timing parameters + * which must be calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 3.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * ====== XPedite550x DDR3-800 read delay calculations ====== + * + * The P2020 processor provides an autoleveling option. Setting CPO to + * 0x1f enables this auto configuration. + */ + +typedef struct { + unsigned short datarate_mhz_low; + unsigned short datarate_mhz_high; + unsigned char clk_adjust; + unsigned char cpo; +} board_specific_parameters_t; + +const board_specific_parameters_t board_specific_parameters[][20] = { + { + /* Controller 0 */ + { + /* DDR3-600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo = 31, + }, + { + /* DDR3-800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo = 31, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const board_specific_parameters_t *pbsp = + &(board_specific_parameters[ctrl_num][0]); + u32 num_params = sizeof(board_specific_parameters[ctrl_num]) / + sizeof(board_specific_parameters[0][0]); + u32 i; + ulong ddr_freq; + + /* + * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in + * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If + * there are two dimms in the controller, set odt_rd_cfg to 3 and + * odt_wr_cfg to 3 for the even CS, 0 for the odd CS. + */ + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + if (i&1) { /* odd CS */ + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 0; + } else { /* even CS */ + if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) { + popts->cs_local_opts[i].odt_rd_cfg = 0; + popts->cs_local_opts[i].odt_wr_cfg = 4; + } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) { + popts->cs_local_opts[i].odt_rd_cfg = 3; + popts->cs_local_opts[i].odt_wr_cfg = 3; + } + } + } + + /* + * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + + for (i = 0; i < num_params; i++) { + if (ddr_freq >= pbsp->datarate_mhz_low && + ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->cpo_override = pbsp->cpo; + popts->twoT_en = 0; + } + pbsp++; + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + + /* + * Enable on-die termination. + * From the Micron Technical Node TN-41-04, RTT_Nom should typically + * be 30 to 40 ohms, while RTT_WR should be 120 ohms. Setting RTT_WR + * is handled in the Freescale DDR3 driver. Set RTT_Nom here. + */ + popts->rtt_override = 1; + popts->rtt_override_value = 3; +} + diff --git a/board/xes/xpedite550x/law.c b/board/xes/xpedite550x/law.c new file mode 100644 index 0000000..4d4445d --- /dev/null +++ b/board/xes/xpedite550x/law.c @@ -0,0 +1,54 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_PCIE1_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCIE_1), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_1), +#endif +#ifdef CONFIG_SYS_PCIE2_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_2), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_2), +#endif +#ifdef CONFIG_SYS_PCIE3_MEM_PHYS + SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_3), + SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_3), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/xes/xpedite550x/tlb.c b/board/xes/xpedite550x/tlb.c new file mode 100644 index 0000000..cf3ff4d --- /dev/null +++ b/board/xes/xpedite550x/tlb.c @@ -0,0 +1,98 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + + /* **M** - Boot page for secondary processors */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 3, BOOKE_PAGESZ_4K, 1), + +#ifdef CONFIG_PCIE1 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), +#endif + +#ifdef CONFIG_PCIE2 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), +#endif + +#ifdef CONFIG_PCIE3 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_64M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/xes/xpedite550x/xpedite550x.c b/board/xes/xpedite550x/xpedite550x.c new file mode 100644 index 0000000..2ad30a3 --- /dev/null +++ b/board/xes/xpedite550x/xpedite550x.c @@ -0,0 +1,107 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <pca953x.h> + +DECLARE_GLOBAL_DATA_PTR; + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +static void flash_cs_fixup(void) +{ + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + set_lbc_br(0, CONFIG_SYS_BR1_PRELIM); + set_lbc_or(0, CONFIG_SYS_OR1_PRELIM); + + set_lbc_br(1, CONFIG_SYS_BR0_PRELIM); + set_lbc_or(1, CONFIG_SYS_OR0_PRELIM); + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif + +#ifdef CONFIG_MP +extern void cpu_mp_lmb_reserve(struct lmb *lmb); + +void board_lmb_reserve(struct lmb *lmb) +{ + cpu_mp_lmb_reserve(lmb); +} +#endif @@ -556,8 +556,9 @@ MPC8540ADS powerpc mpc85xx mpc8540ads freescale MPC8544DS powerpc mpc85xx mpc8544ds freescale MPC8560ADS powerpc mpc85xx mpc8560ads freescale MPC8568MDS powerpc mpc85xx mpc8568mds freescale -XPEDITE5200 powerpc mpc85xx xpedite5200 xes -XPEDITE5370 powerpc mpc85xx xpedite5370 xes +xpedite520x powerpc mpc85xx - xes +xpedite537x powerpc mpc85xx - xes +xpedite550x powerpc mpc85xx - xes sbc8540_33 powerpc mpc85xx sbc8560 - - SBC8540 sbc8540_66 powerpc mpc85xx sbc8560 - - SBC8540 sbc8548_PCI_33 powerpc mpc85xx sbc8548 - - sbc8548:PCI,33 @@ -597,7 +598,7 @@ P2020RDB_NAND powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020,NAND P2020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020,SDCARD sbc8641d powerpc mpc86xx MPC8610HPCD powerpc mpc86xx mpc8610hpcd freescale -XPEDITE5170 powerpc mpc86xx xpedite5170 xes +xpedite517x powerpc mpc86xx - xes MPC8641HPCN powerpc mpc86xx mpc8641hpcn freescale - MPC8641HPCN cogent_mpc8xx powerpc mpc8xx cogent ESTEEM192E powerpc mpc8xx esteem192e @@ -648,7 +649,7 @@ CPCIISER4 powerpc ppc4xx cpciiser4 esd DASA_SIM powerpc ppc4xx dasa_sim esd PMC405DE powerpc ppc4xx pmc405de esd METROBOX powerpc ppc4xx metrobox sandburst -XPEDITE1000 powerpc ppc4xx xpedite1000 xes +xpedite1000 powerpc ppc4xx - xes korat_perm powerpc ppc4xx korat - - korat:KORAT_PERMANENT haleakala powerpc ppc4xx kilauea amcc - kilauea:HALEAKALA sycamore powerpc ppc4xx walnut amcc - walnut diff --git a/common/cmd_pci.c b/common/cmd_pci.c index 4bde059..ccf5ada 100644 --- a/common/cmd_pci.c +++ b/common/cmd_pci.c @@ -497,6 +497,10 @@ int do_pci (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) if ((bdf = get_pci_dev(argv[2])) == -1) return 1; break; +#ifdef CONFIG_CMD_PCI_ENUM + case 'e': + break; +#endif default: /* scan bus */ value = 1; /* short listing */ bdf = 0; /* bus number */ @@ -518,6 +522,11 @@ int do_pci (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) return 0; case 'd': /* display */ return pci_cfg_display(bdf, addr, size, value); +#ifdef CONFIG_CMD_PCI_ENUM + case 'e': + pci_init(); + return 0; +#endif case 'n': /* next */ if (argc < 4) goto usage; @@ -545,6 +554,10 @@ U_BOOT_CMD( "list and access PCI Configuration Space", "[bus] [long]\n" " - short or long list of PCI devices on bus 'bus'\n" +#ifdef CONFIG_CMD_PCI_ENUM + "pci enum\n" + " - re-enumerate PCI buses\n" +#endif "pci header b.d.f\n" " - show header of PCI device 'bus.device.function'\n" "pci display[.b, .w, .l] b.d.f [address] [# of objects]\n" diff --git a/doc/README.POST b/doc/README.POST index eeb218d..6815d49 100644 --- a/doc/README.POST +++ b/doc/README.POST @@ -659,12 +659,19 @@ not need any modifications for porting them to another board/CPU. 2.2.2.1. I2C test For verifying the I2C bus, a full I2C bus scanning will be performed -using the i2c_probe() routine. If any I2C device is found, the test -will be considered as passed, otherwise failed. This particular way -will be used because it provides the most common method of testing. -For example, using the internal loopback mode of the CPM I2C -controller for testing would not work on boards where the software -I2C driver (also known as bit-banged driver) is used. +using the i2c_probe() routine. If a board defines +CONFIG_SYS_POST_I2C_ADDRS the I2C test will pass if all devices +listed in CONFIG_SYS_POST_I2C_ADDRS are found, and no additional +devices are detected. If CONFIG_SYS_POST_I2C_ADDRS is not defined +the test will pass if any I2C device is found. + +The CONFIG_SYS_POST_I2C_IGNORES define can be used to list I2C +devices which may or may not be present when using +CONFIG_SYS_POST_I2C_ADDRS. The I2C POST test will pass regardless +if the devices in CONFIG_SYS_POST_I2C_IGNORES are found or not. +This is useful in cases when I2C devices are optional (eg on a +daughtercard that may or may not be present) or not critical +to board operation. 2.2.2.2. Watchdog timer test diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c index 001e6eb..1f02103 100644 --- a/drivers/pci/fsl_pci_init.c +++ b/drivers/pci/fsl_pci_init.c @@ -91,6 +91,9 @@ int fsl_setup_hose(struct pci_controller *hose, unsigned long addr) { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) addr; + /* Reset hose to make sure its in a clean state */ + memset(hose, 0, sizeof(struct pci_controller)); + pci_setup_indirect(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data); return fsl_is_pci_agent(hose); diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index cd64a87..848746f 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -139,7 +139,7 @@ void *pci_map_bar(pci_dev_t pdev, int bar, int flags) * */ -static struct pci_controller* hose_head = NULL; +static struct pci_controller* hose_head; void pci_register_hose(struct pci_controller* hose) { @@ -640,6 +640,8 @@ void pci_init(void) } #endif /* CONFIG_PCI_BOOTDELAY */ + hose_head = NULL; + /* now call board specific pci_init()... */ pci_init_board(); } diff --git a/include/configs/KUP4K.h b/include/configs/KUP4K.h index 9702d63..c8e0ff2 100644 --- a/include/configs/KUP4K.h +++ b/include/configs/KUP4K.h @@ -139,9 +139,9 @@ /* List of I2C addresses to be verified by POST */ -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_PICIO_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - } +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_PICIO_ADDR, \ + CONFIG_SYS_I2C_RTC_ADDR, \ + } #define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */ diff --git a/include/configs/KUP4X.h b/include/configs/KUP4X.h index 9613ed9..ce731e3 100644 --- a/include/configs/KUP4X.h +++ b/include/configs/KUP4X.h @@ -149,9 +149,9 @@ /* List of I2C addresses to be verified by POST */ -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_PICIO_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - } +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_PICIO_ADDR, \ + CONFIG_SYS_I2C_RTC_ADDR, \ + } #define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */ diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h index ad86e2e..f336e8d 100644 --- a/include/configs/TB5200.h +++ b/include/configs/TB5200.h @@ -251,10 +251,10 @@ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 /* List of I2C addresses to be verified by POST */ -#undef I2C_ADDR_LIST -#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_SLAVE } +#undef CONFIG_SYS_POST_I2C_ADDRS +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ + CONFIG_SYS_I2C_RTC_ADDR, \ + CONFIG_SYS_I2C_SLAVE} /* * Flash configuration diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 2612c7a..794e11b 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -370,10 +370,10 @@ /* List of I2C addresses to be verified by POST */ #if defined (CONFIG_MINIFAP) -#undef I2C_ADDR_LIST -#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_HWMON_ADDR, \ - CONFIG_SYS_I2C_SLAVE } +#undef CONFIG_SYS_POST_I2C_ADDRS +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ + CONFIG_SYS_I2C_HWMON_ADDR, \ + CONFIG_SYS_I2C_SLAVE} #endif /* diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h index 1b129a2..af6769b 100644 --- a/include/configs/cm5200.h +++ b/include/configs/cm5200.h @@ -80,7 +80,9 @@ #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C) #define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) /* List of I2C addresses to be verified by POST */ -#define I2C_ADDR_LIST { CONFIG_SYS_I2C_SLAVE, CONFIG_SYS_I2C_IO, CONFIG_SYS_I2C_EEPROM } +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \ + CONFIG_SYS_I2C_IO, \ + CONFIG_SYS_I2C_EEPROM} /* display image timestamps */ #define CONFIG_TIMESTAMP 1 diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index 85147d0..2733fb2 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -213,7 +213,7 @@ #endif #define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h index 1062765..9e48857 100644 --- a/include/configs/lwmon.h +++ b/include/configs/lwmon.h @@ -349,32 +349,32 @@ /* List of I2C addresses to be verified by POST */ #ifdef CONFIG_USE_FRAM -#define I2C_ADDR_LIST { /* CONFIG_SYS_I2C_AUDIO_ADDR, */ \ - CONFIG_SYS_I2C_SYSMON_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_POWER_A_ADDR, \ - CONFIG_SYS_I2C_POWER_B_ADDR, \ - CONFIG_SYS_I2C_KEYBD_ADDR, \ - CONFIG_SYS_I2C_PICIO_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - } +#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \ + CONFIG_SYS_I2C_SYSMON_ADDR, \ + CONFIG_SYS_I2C_RTC_ADDR, \ + CONFIG_SYS_I2C_POWER_A_ADDR, \ + CONFIG_SYS_I2C_POWER_B_ADDR, \ + CONFIG_SYS_I2C_KEYBD_ADDR, \ + CONFIG_SYS_I2C_PICIO_ADDR, \ + CONFIG_SYS_I2C_EEPROM_ADDR, \ + } #else /* Use EEPROM - which show up on 8 consequtive addresses */ -#define I2C_ADDR_LIST { /* CONFIG_SYS_I2C_AUDIO_ADDR, */ \ - CONFIG_SYS_I2C_SYSMON_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_POWER_A_ADDR, \ - CONFIG_SYS_I2C_POWER_B_ADDR, \ - CONFIG_SYS_I2C_KEYBD_ADDR, \ - CONFIG_SYS_I2C_PICIO_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR+0, \ - CONFIG_SYS_I2C_EEPROM_ADDR+1, \ - CONFIG_SYS_I2C_EEPROM_ADDR+2, \ - CONFIG_SYS_I2C_EEPROM_ADDR+3, \ - CONFIG_SYS_I2C_EEPROM_ADDR+4, \ - CONFIG_SYS_I2C_EEPROM_ADDR+5, \ - CONFIG_SYS_I2C_EEPROM_ADDR+6, \ - CONFIG_SYS_I2C_EEPROM_ADDR+7, \ - } +#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \ + CONFIG_SYS_I2C_SYSMON_ADDR, \ + CONFIG_SYS_I2C_RTC_ADDR, \ + CONFIG_SYS_I2C_POWER_A_ADDR, \ + CONFIG_SYS_I2C_POWER_B_ADDR, \ + CONFIG_SYS_I2C_KEYBD_ADDR, \ + CONFIG_SYS_I2C_PICIO_ADDR, \ + CONFIG_SYS_I2C_EEPROM_ADDR+0, \ + CONFIG_SYS_I2C_EEPROM_ADDR+1, \ + CONFIG_SYS_I2C_EEPROM_ADDR+2, \ + CONFIG_SYS_I2C_EEPROM_ADDR+3, \ + CONFIG_SYS_I2C_EEPROM_ADDR+4, \ + CONFIG_SYS_I2C_EEPROM_ADDR+5, \ + CONFIG_SYS_I2C_EEPROM_ADDR+6, \ + CONFIG_SYS_I2C_EEPROM_ADDR+7, \ + } #endif /* CONFIG_USE_FRAM */ /*----------------------------------------------------------------------- diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index a4e92cc..63e22d4 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -306,14 +306,13 @@ #define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ #define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ -#define I2C_ADDR_LIST { \ - CONFIG_SYS_I2C_RTC_ADDR, \ - CONFIG_SYS_I2C_EEPROM_CPU_ADDR, \ - CONFIG_SYS_I2C_EEPROM_MB_ADDR, \ - CONFIG_SYS_I2C_DSPIC_ADDR, \ - CONFIG_SYS_I2C_DSPIC_2_ADDR, \ - CONFIG_SYS_I2C_DSPIC_KEYB_ADDR, \ - CONFIG_SYS_I2C_DSPIC_IO_ADDR } +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_RTC_ADDR, \ + CONFIG_SYS_I2C_EEPROM_CPU_ADDR,\ + CONFIG_SYS_I2C_EEPROM_MB_ADDR, \ + CONFIG_SYS_I2C_DSPIC_ADDR, \ + CONFIG_SYS_I2C_DSPIC_2_ADDR, \ + CONFIG_SYS_I2C_DSPIC_KEYB_ADDR,\ + CONFIG_SYS_I2C_DSPIC_IO_ADDR } /* * Pass open firmware flat tree diff --git a/include/configs/spieval.h b/include/configs/spieval.h index b5ac168..880c8a3 100644 --- a/include/configs/spieval.h +++ b/include/configs/spieval.h @@ -271,10 +271,10 @@ /* List of I2C addresses to be verified by POST */ #if defined (CONFIG_MINIFAP) -#undef I2C_ADDR_LIST -#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_HWMON_ADDR, \ - CONFIG_SYS_I2C_SLAVE } +#undef CONFIG_SYS_POST_I2C_ADDRS +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ + CONFIG_SYS_I2C_HWMON_ADDR, \ + CONFIG_SYS_I2C_SLAVE} #endif /* diff --git a/include/configs/XPEDITE1000.h b/include/configs/xpedite1000.h index 5605849..d0f9363 100644 --- a/include/configs/XPEDITE1000.h +++ b/include/configs/xpedite1000.h @@ -33,6 +33,7 @@ /* High Level Configuration Options */ #define CONFIG_XPEDITE1000 1 #define CONFIG_SYS_BOARD_NAME "XPedite1000" +#define CONFIG_SYS_FORM_PMC 1 #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_440 1 #define CONFIG_440GX 1 /* 440 GX */ @@ -341,8 +342,8 @@ extern void out32(unsigned int, unsigned long); "misc_args=ip=on\0" \ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ "bootfile=/home/user/file\0" \ - "osfile=/home/user/uImage-XPedite1000\0" \ - "fdtfile=/home/user/xpedite1000.dtb\0" \ + "osfile=/home/user/board.uImage\0" \ + "fdtfile=/home/user/board.dtb\0" \ "ubootfile=/home/user/u-boot.bin\0" \ "fdtaddr=c00000\0" \ "osaddr=0x1000000\0" \ diff --git a/include/configs/XPEDITE5170.h b/include/configs/xpedite517x.h index 1851997..8df9edd 100644 --- a/include/configs/XPEDITE5170.h +++ b/include/configs/xpedite517x.h @@ -22,7 +22,7 @@ */ /* - * xpedite5170 board configuration file + * xpedite517x board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H @@ -34,6 +34,7 @@ #define CONFIG_MPC8641 1 /* MPC8641 specific */ #define CONFIG_XPEDITE5140 1 /* MPC8641HPCN board specific */ #define CONFIG_SYS_BOARD_NAME "XPedite5170" +#define CONFIG_SYS_FORM_3U_VPX 1 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ @@ -107,6 +108,21 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_ALT_MEMTEST #define CONFIG_SYS_MEMTEST_START 0x10000000 #define CONFIG_SYS_MEMTEST_END 0x20000000 +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\ + CONFIG_SYS_POST_I2C) +#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ + CONFIG_SYS_I2C_DS4510_ADDR, \ + CONFIG_SYS_I2C_EEPROM_ADDR, \ + CONFIG_SYS_I2C_LM90_ADDR, \ + CONFIG_SYS_I2C_PCA9553_ADDR, \ + CONFIG_SYS_I2C_PCA953X_ADDR0, \ + CONFIG_SYS_I2C_PCA953X_ADDR1, \ + CONFIG_SYS_I2C_PCA953X_ADDR2, \ + CONFIG_SYS_I2C_PCA953X_ADDR3, \ + CONFIG_SYS_I2C_PEX8518_ADDR, \ + CONFIG_SYS_I2C_RTC_ADDR} +/* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */ +#define I2C_ADDR_IGNORE_LIST {0x50} /* * Memory map @@ -258,6 +274,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 #define CONFIG_DTT_DS1621 #define CONFIG_DTT_SENSORS { 0 } +#define CONFIG_SYS_I2C_LM90_ADDR 0x4c /* I2C EEPROM - AT24C128B */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 @@ -281,6 +298,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 +#define CONFIG_SYS_I2C_PCA9553_ADDR 0x62 /* * PU = pulled high, PD = pulled low @@ -324,18 +342,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * Memory space is mapped 1-1, but I/O space must start from 0. */ /* PCIE1 - PEX8518 */ -#define CONFIG_SYS_PCIE1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ /* PCIE2 - VPX P1 */ -#define CONFIG_SYS_PCIE2_MEM_BASE 0xc0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE +#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ @@ -545,6 +563,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_CMD_PCA953X #define CONFIG_CMD_PCA953X_INFO #define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI_ENUM #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO #define CONFIG_CMD_SNTP @@ -725,8 +744,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); "misc_args=ip=on\0" \ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ "bootfile=/home/user/file\0" \ - "osfile=/home/user/uImage-XPedite5170\0" \ - "fdtfile=/home/user/xpedite5170.dtb\0" \ + "osfile=/home/user/board.uImage\0" \ + "fdtfile=/home/user/board.dtb\0" \ "ubootfile=/home/user/u-boot.bin\0" \ "fdtaddr=c00000\0" \ "osaddr=0x1000000\0" \ diff --git a/include/configs/XPEDITE5200.h b/include/configs/xpedite520x.h index d0e9492..2f31337 100644 --- a/include/configs/XPEDITE5200.h +++ b/include/configs/xpedite520x.h @@ -22,7 +22,7 @@ */ /* - * xpedite5200 board configuration file + * xpedite520x board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H @@ -36,6 +36,7 @@ #define CONFIG_MPC8548 1 #define CONFIG_XPEDITE5200 1 #define CONFIG_SYS_BOARD_NAME "XPedite5200" +#define CONFIG_SYS_FORM_PMC_XMC 1 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ #ifndef CONFIG_SYS_TEXT_BASE @@ -92,6 +93,13 @@ #define CONFIG_SYS_ALT_MEMTEST #define CONFIG_SYS_MEMTEST_START 0x10000000 #define CONFIG_SYS_MEMTEST_END 0x20000000 +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_I2C) +#define I2C_ADDR_LIST {CONFIG_SYS_I2C_MAX1237_ADDR, \ + CONFIG_SYS_I2C_EEPROM_ADDR, \ + CONFIG_SYS_I2C_PCA953X_ADDR0, \ + CONFIG_SYS_I2C_PCA953X_ADDR1, \ + CONFIG_SYS_I2C_RTC_ADDR} /* * Memory map @@ -250,7 +258,7 @@ #define CONFIG_SYS_PCA953X_BRD_CFG2 0x04 #define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08 #define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10 -#define CONFIG_SYS_PCA953X_FLASH_WP 0x20 +#define CONFIG_SYS_PCA953X_NVM_WP 0x20 #define CONFIG_SYS_PCA953X_MONARCH 0x40 #define CONFIG_SYS_PCA953X_EREADY 0x80 @@ -264,14 +272,17 @@ #define CONFIG_SYS_PCA953X_P14_IO6 0x40 #define CONFIG_SYS_PCA953X_P14_IO7 0x80 +/* 12-bit ADC used to measure CPU diode */ +#define CONFIG_SYS_I2C_MAX1237_ADDR 0x34 + /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS #define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 #define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000 #define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */ @@ -339,6 +350,7 @@ #define CONFIG_CMD_PCA953X #define CONFIG_CMD_PCA953X_INFO #define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI_ENUM #define CONFIG_CMD_PING #define CONFIG_CMD_SNTP #define CONFIG_CMD_REGINFO @@ -521,8 +533,8 @@ "misc_args=ip=on\0" \ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ "bootfile=/home/user/file\0" \ - "osfile=/home/user/uImage-XPedite5200\0" \ - "fdtfile=/home/user/xpedite5200.dtb\0" \ + "osfile=/home/user/board.uImage\0" \ + "fdtfile=/home/user/board.dtb\0" \ "ubootfile=/home/user/u-boot.bin\0" \ "fdtaddr=c00000\0" \ "osaddr=0x1000000\0" \ diff --git a/include/configs/XPEDITE5370.h b/include/configs/xpedite537x.h index 629dc0d..e7de13a 100644 --- a/include/configs/XPEDITE5370.h +++ b/include/configs/xpedite537x.h @@ -22,7 +22,7 @@ */ /* - * xpedite5370 board configuration file + * xpedite537x board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H @@ -36,6 +36,7 @@ #define CONFIG_MPC8572 1 #define CONFIG_XPEDITE5370 1 #define CONFIG_SYS_BOARD_NAME "XPedite5370" +#define CONFIG_SYS_FORM_3U_VPX 1 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ #ifndef CONFIG_SYS_TEXT_BASE @@ -110,6 +111,20 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_ALT_MEMTEST #define CONFIG_SYS_MEMTEST_START 0x10000000 #define CONFIG_SYS_MEMTEST_END 0x20000000 +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_I2C) +#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ + CONFIG_SYS_I2C_DS4510_ADDR, \ + CONFIG_SYS_I2C_EEPROM_ADDR, \ + CONFIG_SYS_I2C_LM90_ADDR, \ + CONFIG_SYS_I2C_PCA953X_ADDR0, \ + CONFIG_SYS_I2C_PCA953X_ADDR1, \ + CONFIG_SYS_I2C_PCA953X_ADDR2, \ + CONFIG_SYS_I2C_PCA953X_ADDR3, \ + CONFIG_SYS_I2C_PEX8518_ADDR, \ + CONFIG_SYS_I2C_RTC_ADDR} +/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ +#define I2C_ADDR_IGNORE_LIST {0x50} /* * Memory map @@ -265,6 +280,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 #define CONFIG_DTT_DS1621 #define CONFIG_DTT_SENSORS { 0 } +#define CONFIG_SYS_I2C_LM90_ADDR 0x4c /* I2C EEPROM - AT24C128B */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 @@ -334,18 +350,18 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); * Memory space is mapped 1-1, but I/O space must start from 0. */ /* PCIE1 - VPX P1 */ -#define CONFIG_SYS_PCIE1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ /* PCIE2 - PEX8518 */ -#define CONFIG_SYS_PCIE2_MEM_BASE 0xc0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE +#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ @@ -396,6 +412,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); #define CONFIG_CMD_PCA953X #define CONFIG_CMD_PCA953X_INFO #define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI_ENUM #define CONFIG_CMD_PING #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_SNTP @@ -578,8 +595,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); "misc_args=ip=on\0" \ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ "bootfile=/home/user/file\0" \ - "osfile=/home/user/uImage-XPedite5370\0" \ - "fdtfile=/home/user/xpedite5370.dtb\0" \ + "osfile=/home/user/board.uImage\0" \ + "fdtfile=/home/user/board.dtb\0" \ "ubootfile=/home/user/u-boot.bin\0" \ "fdtaddr=c00000\0" \ "osaddr=0x1000000\0" \ diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h new file mode 100644 index 0000000..a849cf9 --- /dev/null +++ b/include/configs/xpedite550x.h @@ -0,0 +1,607 @@ +/* + * Copyright 2010 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * xpedite550x board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_P2020 1 +#define CONFIG_XPEDITE550X 1 +#define CONFIG_SYS_BOARD_NAME "XPedite5500" +#define CONFIG_SYS_FORM_PMC_XMC 1 +#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xfff80000 +#endif + +#define CONFIG_PCI 1 /* Enable PCI/PCIE */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ +#define CONFIG_FSL_ELBC 1 + +/* + * Multicore config + */ +#define CONFIG_MP +#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ +#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ + +/* + * DDR config + */ +#define CONFIG_FSL_DDR3 +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS1 0x54 +#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +extern unsigned long get_board_ddr_clk(unsigned long dummy); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ + +/* + * Diagnostics + */ +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x20000000 +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_I2C) +#define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \ + CONFIG_SYS_I2C_LM75_ADDR, \ + CONFIG_SYS_I2C_LM90_ADDR, \ + CONFIG_SYS_I2C_PCA953X_ADDR0, \ + CONFIG_SYS_I2C_PCA953X_ADDR2, \ + CONFIG_SYS_I2C_PCA953X_ADDR3, \ + CONFIG_SYS_I2C_RTC_ADDR} + +/* + * Memory map + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable + * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable + * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable + * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable + * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable + * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable + * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable + * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable + */ + +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) + +/* + * NAND flash configuration + */ +#define CONFIG_SYS_NAND_BASE 0xef800000 +#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ + CONFIG_SYS_NAND_BASE2} +#define CONFIG_SYS_MAX_NAND_DEVICE 2 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */ +#define CONFIG_NAND_FSL_ELBC + +/* + * NOR flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 +#define CONFIG_SYS_FLASH_BASE2 0xf0000000 +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ + {0xf7f40000, 0xc0000} } +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +/* + * Chip select configuration + */ +/* NOR Flash 0 on CS0 */ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ + OR_GPCM_CSNT | \ + OR_GPCM_XACS | \ + OR_GPCM_ACS_DIV2 | \ + OR_GPCM_SCY_8 | \ + OR_GPCM_TRLX | \ + OR_GPCM_EHTR | \ + OR_GPCM_EAD) + +/* NOR Flash 1 on CS1 */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ + BR_PS_16 | \ + BR_V) +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM + +/* NAND flash on CS2 */ +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ + (2<<BR_DECC_SHIFT) | \ + BR_PS_8 | \ + BR_MS_FCM | \ + BR_V) + +/* NAND flash on CS2 */ +#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ + OR_FCM_PGS | \ + OR_FCM_CSCT | \ + OR_FCM_CST | \ + OR_FCM_CHT | \ + OR_FCM_SCY_1 | \ + OR_FCM_TRLX | \ + OR_FCM_EHTR) + +/* NAND flash on CS3 */ +#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ + (2<<BR_DECC_SHIFT) | \ + BR_PS_8 | \ + BR_MS_FCM | \ + BR_V) +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM + +/* + * Use L1 as initial stack + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 +#define CONFIG_SYS_INIT_RAM_END 0x00004000 + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} +#define CONFIG_BAUDRATE 115200 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Use the HUSH parser + */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 +#define CONFIG_FDT_FIXUP_PCI_IRQ 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_I2C_MULTI_BUS + +/* I2C DS7505 temperature sensor */ +#define CONFIG_DTT_LM75 +#define CONFIG_DTT_SENSORS { 0 } +#define CONFIG_SYS_I2C_LM75_ADDR 0x48 + +/* I2C ADT7461 temperature sensor */ +#define CONFIG_SYS_I2C_LM90_ADDR 0x4C + +/* I2C EEPROM - AT24C128B */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* GPIO */ +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 +#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c +#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e +#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f +#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 + +/* + * GPIO pin definitions, PU = pulled high, PD = pulled low + */ +/* PCA9557 @ 0x18*/ +#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */ +#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ +#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */ +#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ +#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */ + +/* PCA9557 @ 0x1e*/ +#define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */ +#define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */ +#define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */ +#define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */ +#define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */ +#define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */ +#define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */ + +/* PCA9557 @ 0x1f */ +#define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */ +#define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */ +#define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */ +#define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */ +#define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */ +#define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */ +#define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */ +#define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */ + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1 - PEX8112 or XMC, depending on build option */ +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ + + +/* + * Networking options + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_TSEC_TBI +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_ETHPRIME "eTSEC2" + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define CONFIG_HAS_ETH0 + +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_PHY_ADDR 2 +#define TSEC2_PHYIDX 0 +#define CONFIG_HAS_ETH1 + +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_PHY_ADDR 3 +#define TSEC3_PHYIDX 0 +#define CONFIG_HAS_ETH2 + +/* + * USB + */ +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_DOS_PARTITION + +/* + * Command configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI_ENUM +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SAVEENV +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ +#define CONFIG_PANIC_HANG /* do not reset board on panic */ +#define CONFIG_PREBOOT /* enable preboot variable */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 +#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ + +/* + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) + +/* + * Flash memory map: + * fff80000 - ffffffff Pri U-Boot (512 KB) + * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) + * fff00000 - fff3ffff Pri FDT (256KB) + * fef00000 - ffefffff Pri OS image (16MB) + * f8000000 - feefffff Pri OS Use/Filesystem (111MB) + * + * f7f80000 - f7ffffff Sec U-Boot (512 KB) + * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) + * f7f00000 - f7f3ffff Sec FDT (256KB) + * f6f00000 - f7efffff Sec OS image (16MB) + * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) + */ +#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000) +#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000) +#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000) +#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000) +#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) +#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000) + +#define CONFIG_PROG_UBOOT1 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_UBOOT2 \ + "$download_cmd $loadaddr $ubootfile; " \ + "if test $? -eq 0; then " \ + "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ + "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ + "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ + "if test $? -ne 0; then " \ + "echo PROGRAM FAILED; " \ + "else; " \ + "echo PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_BOOT_OS_NET \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "if test -n $fdtaddr; then " \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "bootm $osaddr - $fdtaddr; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi; " \ + "else; " \ + "bootm $osaddr; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS1 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_OS2 \ + "$download_cmd $osaddr $osfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ + "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo OS PROGRAM FAILED; " \ + "else; " \ + "echo OS PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo OS DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT1 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_PROG_FDT2 \ + "$download_cmd $fdtaddr $fdtfile; " \ + "if test $? -eq 0; then " \ + "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ + "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ + "if test $? -ne 0; then " \ + "echo FDT PROGRAM FAILED; " \ + "else; " \ + "echo FDT PROGRAM SUCCEEDED; " \ + "fi; " \ + "else; " \ + "echo FDT DOWNLOAD FAILED; " \ + "fi;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=yes\0" \ + "download_cmd=tftp\0" \ + "console_args=console=ttyS0,115200\0" \ + "root_args=root=/dev/nfs rw\0" \ + "misc_args=ip=on\0" \ + "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ + "bootfile=/home/user/file\0" \ + "osfile=/home/user/board.uImage\0" \ + "fdtfile=/home/user/board.dtb\0" \ + "ubootfile=/home/user/u-boot.bin\0" \ + "fdtaddr=c00000\0" \ + "osaddr=0x1000000\0" \ + "loadaddr=0x1000000\0" \ + "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ + "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ + "prog_os1="CONFIG_PROG_OS1"\0" \ + "prog_os2="CONFIG_PROG_OS2"\0" \ + "prog_fdt1="CONFIG_PROG_FDT1"\0" \ + "prog_fdt2="CONFIG_PROG_FDT2"\0" \ + "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ + "bootcmd_flash1=run set_bootargs; " \ + "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ + "bootcmd_flash2=run set_bootargs; " \ + "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ + "bootcmd=run bootcmd_flash1\0" +#endif /* __CONFIG_H */ diff --git a/include/post.h b/include/post.h index daa9047..abe47da 100644 --- a/include/post.h +++ b/include/post.h @@ -60,6 +60,10 @@ #include <asm/immap_85xx.h> #define _POST_WORD_ADDR (CONFIG_SYS_IMMR + offsetof(ccsr_pic_t, tfrr)) +#elif defined (CONFIG_MPC86xx) +#include <asm/immap_86xx.h> +#define _POST_WORD_ADDR (CONFIG_SYS_IMMR + offsetof(ccsr_pic_t, tfrr)) + #elif defined (CONFIG_4xx) #define _POST_WORD_ADDR \ (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 0x4) diff --git a/post/drivers/i2c.c b/post/drivers/i2c.c index b152dea..3080e81 100644 --- a/post/drivers/i2c.c +++ b/post/drivers/i2c.c @@ -21,70 +21,89 @@ * MA 02111-1307 USA */ -#include <common.h> - /* * I2C test * * For verifying the I2C bus, a full I2C bus scanning is performed. * - * #ifdef I2C_ADDR_LIST - * The test is considered as passed if all the devices and - * only the devices in the list are found. - * #else [ ! I2C_ADDR_LIST ] + * #ifdef CONFIG_SYS_POST_I2C_ADDRS + * The test is considered as passed if all the devices and only the devices + * in the list are found. + * #ifdef CONFIG_SYS_POST_I2C_IGNORES + * Ignore devices listed in CONFIG_SYS_POST_I2C_IGNORES. These devices + * are optional or not vital to board functionality. + * #endif + * #else [ ! CONFIG_SYS_POST_I2C_ADDRS ] * The test is considered as passed if any I2C device is found. * #endif */ +#include <common.h> #include <post.h> #include <i2c.h> #if CONFIG_POST & CONFIG_SYS_POST_I2C +static int i2c_ignore_device(unsigned int chip) +{ +#ifdef CONFIG_SYS_POST_I2C_IGNORES + const unsigned char i2c_ignore_list[] = CONFIG_SYS_POST_I2C_IGNORES; + int i; + + for (i = 0; i < sizeof(i2c_ignore_list); i++) + if (i2c_ignore_list[i] == chip) + return 1; +#endif + + return 0; +} + int i2c_post_test (int flags) { unsigned int i; - unsigned int good = 0; -#ifdef I2C_ADDR_LIST - unsigned int bad = 0; +#ifndef CONFIG_SYS_POST_I2C_ADDRS + /* Start at address 1, address 0 is the general call address */ + for (i = 1; i < 128; i++) + if (i2c_ignore_device(i)) + continue; + if (i2c_probe (i) == 0) + return 0; + + /* No devices found */ + return -1; +#else + unsigned int ret = 0; int j; - unsigned char i2c_addr_list[] = I2C_ADDR_LIST; - unsigned char i2c_miss_list[] = I2C_ADDR_LIST; -#endif + const unsigned char i2c_addr_list[] = CONFIG_SYS_POST_I2C_ADDRS; - for (i = 0; i < 128; i++) { - if (i2c_probe (i) == 0) { -#ifndef I2C_ADDR_LIST - good++; -#else /* I2C_ADDR_LIST */ - for (j=0; j<sizeof(i2c_addr_list); ++j) { - if (i == i2c_addr_list[j]) { - good++; - i2c_miss_list[j] = 0xFF; - break; - } - } - if (j == sizeof(i2c_addr_list)) { - bad++; - post_log ("I2C: addr %02X not expected\n", - i); + /* Start at address 1, address 0 is the general call address */ + for (i = 1; i < 128; i++) { + if (i2c_ignore_device(i)) + continue; + if (i2c_probe(i) != 0) + continue; + + for (j = 0; j < sizeof(i2c_addr_list); ++j) { + if (i == i2c_addr_list[j]) { + i2c_addr_list[j] = 0xff; + break; } -#endif /* I2C_ADDR_LIST */ } - } -#ifndef I2C_ADDR_LIST - return good > 0 ? 0 : -1; -#else /* I2C_ADDR_LIST */ - if (good != sizeof(i2c_addr_list)) { - for (j=0; j<sizeof(i2c_miss_list); ++j) { - if (i2c_miss_list[j] != 0xFF) { - post_log ("I2C: addr %02X did not respond\n", - i2c_miss_list[j]); - } + if (j == sizeof(i2c_addr_list)) { + ret = -1; + post_log("I2C: addr %02x not expected\n", i); } } - return ((good == sizeof(i2c_addr_list)) && (bad == 0)) ? 0 : -1; + + for (i = 0; i < sizeof(i2c_addr_list); ++i) { + if (i2c_addr_list[i] == 0xff) + continue; + post_log("I2C: addr %02x did not respond\n", i2c_addr_list[i]); + ret = -1; + } + + return ret; #endif } |