diff options
| -rwxr-xr-x | MAKEALL | 30 | ||||
| -rw-r--r-- | Makefile | 10 | ||||
| -rw-r--r-- | cpu/ppc4xx/start.S | 221 | ||||
| -rw-r--r-- | include/configs/bamboo.h | 88 | ||||
| -rw-r--r-- | nand_spl/board/amcc/bamboo/Makefile | 100 | ||||
| -rw-r--r-- | nand_spl/board/amcc/bamboo/config.mk | 49 | ||||
| -rw-r--r-- | nand_spl/board/amcc/bamboo/sdram.c | 92 | ||||
| -rw-r--r-- | nand_spl/board/amcc/bamboo/u-boot.lds | 65 |
8 files changed, 536 insertions, 119 deletions
@@ -76,21 +76,21 @@ LIST_8xx=" \ LIST_4xx=" \ acadia ADCIOP alpr AP1000 \ - AR405 ASH405 bamboo bubinga \ - CANBT CMS700 CPCI2DP CPCI405 \ - CPCI4052 CPCI405AB CPCI405DT CPCI440 \ - CPCIISER4 CRAYL1 csb272 csb472 \ - DASA_SIM DP405 DU405 ebony \ - ERIC EXBITGEN G2000 HH405 \ - HUB405 JSE KAREF katmai \ - luan METROBOX MIP405 MIP405T \ - ML2 ml300 ocotea OCRTC \ - ORSG p3p440 PCI405 pcs440ep \ - PIP405 PLU405 PMC405 PPChameleonEVB \ - sbc405 sc3 sequoia sequoia_nand \ - taishan VOH405 VOM405 W7OLMC \ - W7OLMG walnut WUH405 XPEDITE1K \ - yellowstone yosemite yucca \ + AR405 ASH405 bamboo bamboo_nand \ + bubinga CANBT CMS700 CPCI2DP \ + CPCI405 CPCI4052 CPCI405AB CPCI405DT \ + CPCI440 CPCIISER4 CRAYL1 csb272 \ + csb472 DASA_SIM DP405 DU405 \ + ebony ERIC EXBITGEN G2000 \ + HH405 HUB405 JSE KAREF \ + katmai luan METROBOX MIP405 \ + MIP405T ML2 ml300 ocotea \ + OCRTC ORSG p3p440 PCI405 \ + pcs440ep PIP405 PLU405 PMC405 \ + PPChameleonEVB sbc405 sc3 sequoia \ + sequoia_nand taishan VOH405 VOM405 \ + W7OLMC W7OLMG walnut WUH405 \ + XPEDITE1K yellowstone yosemite yucca \ " ######################################################################### @@ -1035,6 +1035,16 @@ ASH405_config: unconfig bamboo_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx bamboo amcc +bamboo_nand_config: unconfig + @mkdir -p $(obj)include + @mkdir -p $(obj)nand_spl + @mkdir -p $(obj)board/amcc/bamboo + @echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h + @echo "Compile NAND boot image for bamboo" + @$(MKCONFIG) -a bamboo ppc ppc4xx bamboo amcc + @echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/bamboo/config.tmp + @echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk + bubinga_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx bubinga amcc diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 3b1586c..fe14ecd 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -110,6 +110,13 @@ # endif #endif /* CFG_INIT_DCACHE_CS */ +#define function_prolog(func_name) .text; \ + .align 2; \ + .globl func_name; \ + func_name: +#define function_epilog(func_name) .type func_name,@function; \ + .size func_name,.-func_name + /* We don't want the MMU yet. */ #undef MSR_KERNEL @@ -388,8 +395,9 @@ rsttlb: tlbwe r0,r1,0x0000 /* Invalidate all entries (V=0)*/ 2: #if defined(CONFIG_NAND_SPL) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* - * Enable internal SRAM + * Enable internal SRAM (only on 440EPx/GRx, 440EP/GR have no OCM) */ lis r2,0x7fff ori r2,r2,0xffff @@ -399,6 +407,45 @@ rsttlb: tlbwe r0,r1,0x0000 /* Invalidate all entries (V=0)*/ mfdcr r1,isram0_pmeg and r1,r1,r2 /* Disable pwr mgmt */ mtdcr isram0_pmeg,r1 +#endif +#if defined(CONFIG_440EP) + /* + * On 440EP with no internal SRAM, we setup SDRAM very early + * and copy the NAND_SPL to SDRAM and jump to it + */ + /* Clear Dcache to use as RAM */ + addis r3,r0,CFG_INIT_RAM_ADDR@h + ori r3,r3,CFG_INIT_RAM_ADDR@l + addis r4,r0,CFG_INIT_RAM_END@h + ori r4,r4,CFG_INIT_RAM_END@l + rlwinm. r5,r4,0,27,31 + rlwinm r5,r4,27,5,31 + beq ..d_ran3 + addi r5,r5,0x0001 +..d_ran3: + mtctr r5 +..d_ag3: + dcbz r0,r3 + addi r3,r3,32 + bdnz ..d_ag3 + /*----------------------------------------------------------------*/ + /* Setup the stack in internal SRAM */ + /*----------------------------------------------------------------*/ + lis r1,CFG_INIT_RAM_ADDR@h + ori r1,r1,CFG_INIT_SP_OFFSET@l + li r0,0 + stwu r0,-4(r1) + stwu r0,-4(r1) /* Terminate call chain */ + + stwu r1,-8(r1) /* Save back chain and move SP */ + lis r0,RESET_VECTOR@h /* Address of reset vector */ + ori r0,r0, RESET_VECTOR@l + stwu r1,-8(r1) /* Save back chain and move SP */ + stw r0,+12(r1) /* Save return addr (underflow vect) */ + sync + bl early_sdram_init + sync +#endif /* CONFIG_440EP */ /* * Copy SPL from cache into internal SRAM @@ -429,7 +476,7 @@ spl_loop: start_ram: sync isync -#endif +#endif /* CONFIG_NAND_SPL */ bl 3f b _start @@ -1137,7 +1184,6 @@ crit_return: lwz r1,GPR1(r1) SYNC rfci -#endif /* CONFIG_NAND_SPL */ /* Cache functions. */ @@ -1255,24 +1301,6 @@ wr_tcr: blr /*------------------------------------------------------------------------------- */ -/* Function: in8 */ -/* Description: Input 8 bits */ -/*------------------------------------------------------------------------------- */ - .globl in8 -in8: - lbz r3,0x0000(r3) - blr - -/*------------------------------------------------------------------------------- */ -/* Function: out8 */ -/* Description: Output 8 bits */ -/*------------------------------------------------------------------------------- */ - .globl out8 -out8: - stb r4,0x0000(r3) - blr - -/*------------------------------------------------------------------------------- */ /* Function: out16 */ /* Description: Output 16 bits */ /*------------------------------------------------------------------------------- */ @@ -1291,15 +1319,6 @@ out16r: blr /*------------------------------------------------------------------------------- */ -/* Function: out32 */ -/* Description: Output 32 bits */ -/*------------------------------------------------------------------------------- */ - .globl out32 -out32: - stw r4,0x0000(r3) - blr - -/*------------------------------------------------------------------------------- */ /* Function: out32r */ /* Description: Byte reverse and output 32 bits */ /*------------------------------------------------------------------------------- */ @@ -1327,15 +1346,6 @@ in16r: blr /*------------------------------------------------------------------------------- */ -/* Function: in32 */ -/* Description: Input 32 bits */ -/*------------------------------------------------------------------------------- */ - .globl in32 -in32: - lwz 3,0x0000(3) - blr - -/*------------------------------------------------------------------------------- */ /* Function: in32r */ /* Description: Input 32 bits and byte reverse */ /*------------------------------------------------------------------------------- */ @@ -1377,9 +1387,6 @@ ppcSync: sync blr -/*------------------------------------------------------------------------------*/ - -#ifndef CONFIG_NAND_SPL /* * void relocate_code (addr_sp, gd, addr_moni) * @@ -1644,8 +1651,88 @@ trap_reloc: stw r0, 4(r7) blr + +#if defined(CONFIG_440) +/*----------------------------------------------------------------------------+ +| dcbz_area. ++----------------------------------------------------------------------------*/ + function_prolog(dcbz_area) + rlwinm. r5,r4,0,27,31 + rlwinm r5,r4,27,5,31 + beq ..d_ra2 + addi r5,r5,0x0001 +..d_ra2:mtctr r5 +..d_ag2:dcbz r0,r3 + addi r3,r3,32 + bdnz ..d_ag2 + sync + blr + function_epilog(dcbz_area) + +/*----------------------------------------------------------------------------+ +| dflush. Assume 32K at vector address is cachable. ++----------------------------------------------------------------------------*/ + function_prolog(dflush) + mfmsr r9 + rlwinm r8,r9,0,15,13 + rlwinm r8,r8,0,17,15 + mtmsr r8 + addi r3,r0,0x0000 + mtspr dvlim,r3 + mfspr r3,ivpr + addi r4,r0,1024 + mtctr r4 +..dflush_loop: + lwz r6,0x0(r3) + addi r3,r3,32 + bdnz ..dflush_loop + addi r3,r3,-32 + mtctr r4 +..ag: dcbf r0,r3 + addi r3,r3,-32 + bdnz ..ag + sync + mtmsr r9 + blr + function_epilog(dflush) +#endif /* CONFIG_440 */ #endif /* CONFIG_NAND_SPL */ +/*------------------------------------------------------------------------------- */ +/* Function: in8 */ +/* Description: Input 8 bits */ +/*------------------------------------------------------------------------------- */ + .globl in8 +in8: + lbz r3,0x0000(r3) + blr + +/*------------------------------------------------------------------------------- */ +/* Function: out8 */ +/* Description: Output 8 bits */ +/*------------------------------------------------------------------------------- */ + .globl out8 +out8: + stb r4,0x0000(r3) + blr + +/*------------------------------------------------------------------------------- */ +/* Function: out32 */ +/* Description: Output 32 bits */ +/*------------------------------------------------------------------------------- */ + .globl out32 +out32: + stw r4,0x0000(r3) + blr + +/*------------------------------------------------------------------------------- */ +/* Function: in32 */ +/* Description: Input 32 bits */ +/*------------------------------------------------------------------------------- */ + .globl in32 +in32: + lwz 3,0x0000(3) + blr /**************************************************************************/ /* PPC405EP specific stuff */ @@ -1892,13 +1979,6 @@ pll_wait: #endif /* CONFIG_405EP */ #if defined(CONFIG_440) -#define function_prolog(func_name) .text; \ - .align 2; \ - .globl func_name; \ - func_name: -#define function_epilog(func_name) .type func_name,@function; \ - .size func_name,.-func_name - /*----------------------------------------------------------------------------+ | mttlb3. +----------------------------------------------------------------------------*/ @@ -1946,47 +2026,4 @@ pll_wait: TLBRE(3,3,0) blr function_epilog(mftlb1) - -/*----------------------------------------------------------------------------+ -| dcbz_area. -+----------------------------------------------------------------------------*/ - function_prolog(dcbz_area) - rlwinm. r5,r4,0,27,31 - rlwinm r5,r4,27,5,31 - beq ..d_ra2 - addi r5,r5,0x0001 -..d_ra2:mtctr r5 -..d_ag2:dcbz r0,r3 - addi r3,r3,32 - bdnz ..d_ag2 - sync - blr - function_epilog(dcbz_area) - -/*----------------------------------------------------------------------------+ -| dflush. Assume 32K at vector address is cachable. -+----------------------------------------------------------------------------*/ - function_prolog(dflush) - mfmsr r9 - rlwinm r8,r9,0,15,13 - rlwinm r8,r8,0,17,15 - mtmsr r8 - addi r3,r0,0x0000 - mtspr dvlim,r3 - mfspr r3,ivpr - addi r4,r0,1024 - mtctr r4 -..dflush_loop: - lwz r6,0x0(r3) - addi r3,r3,32 - bdnz ..dflush_loop - addi r3,r3,-32 - mtctr r4 -..ag: dcbf r0,r3 - addi r3,r3,-32 - bdnz ..ag - sync - mtmsr r9 - blr - function_epilog(dflush) #endif /* CONFIG_440 */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index db58a9f..763d1c7 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -50,7 +50,7 @@ *----------------------------------------------------------------------*/ #define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ #define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) +#define CFG_MONITOR_BASE TEXT_BASE #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ @@ -104,14 +104,11 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -/* - * Define here the location of the environment variables (FLASH or EEPROM). - * Note: DENX encourages to use redundant environment in FLASH. - */ -#if 1 +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #else -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ #endif /*----------------------------------------------------------------------- @@ -133,7 +130,7 @@ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -141,22 +138,89 @@ #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif /* CFG_ENV_IS_IN_FLASH */ +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 4k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 4kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + * On 440EPx the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from cache, I experienced problems accessing + * the NAND controller. sr - 2006-08-25 + */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ + +/* + * Now the NAND chip has to be defined (no autodetection used!) + */ +#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ + +#define CFG_NAND_ECCSIZE 256 +#define CFG_NAND_ECCBYTES 3 +#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) +#define CFG_NAND_OOBSIZE 16 +#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) +#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} + +#ifdef CFG_ENV_IS_IN_NAND +/* + * For NAND booting the environment is embedded in the U-Boot image. Please take + * look at the file board/amcc/sequoia/u-boot-nand.lds for details. + */ +#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE +#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#endif + /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ -#define CFG_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CFG_NAND_CS 1 +#define CFG_MAX_NAND_DEVICE 2 +#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE, CFG_NAND_ADDR + 2 } #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_NAND_CS 1 +#else +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +/* Memory Bank 0 (NAND-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x018003c0 +#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000) +#endif + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------------- */ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ #undef CONFIG_DDR_ECC /* don't use ECC */ #define CFG_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */ -#define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} +#define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} +#define CFG_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ /*----------------------------------------------------------------------- * I2C diff --git a/nand_spl/board/amcc/bamboo/Makefile b/nand_spl/board/amcc/bamboo/Makefile new file mode 100644 index 0000000..0df86f9 --- /dev/null +++ b/nand_spl/board/amcc/bamboo/Makefile @@ -0,0 +1,100 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_NAND_SPL + +SOBJS = start.o init.o resetvec.o +COBJS = nand_boot.o nand_ecc.o ndfc.o sdram.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +nandobj := $(OBJTREE)/nand_spl/ + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin + +all: $(obj).depend $(ALL) + +$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) + cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +# create symbolic links for common files + +# from cpu directory +$(obj)ndfc.c: + @rm -f $(obj)ndfc.c + ln -s $(SRCTREE)/cpu/ppc4xx/ndfc.c $(obj)ndfc.c + +$(obj)resetvec.S: + @rm -f $(obj)resetvec.S + ln -s $(SRCTREE)/cpu/ppc4xx/resetvec.S $(obj)resetvec.S + +$(obj)start.S: + @rm -f $(obj)start.S + ln -s $(SRCTREE)/cpu/ppc4xx/start.S $(obj)start.S + +# from board directory +$(obj)init.S: + @rm -f $(obj)init.S + ln -s $(SRCTREE)/board/amcc/bamboo/init.S $(obj)init.S + +# from nand_spl directory +$(obj)nand_boot.c: + @rm -f $(obj)nand_boot.c + ln -s $(SRCTREE)/nand_spl/nand_boot.c $(obj)nand_boot.c + +# from drivers/nand directory +$(obj)nand_ecc.c: + @rm -f $(obj)nand_ecc.c + ln -s $(SRCTREE)/drivers/nand/nand_ecc.c $(obj)nand_ecc.c + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/amcc/bamboo/config.mk b/nand_spl/board/amcc/bamboo/config.mk new file mode 100644 index 0000000..f7ec751 --- /dev/null +++ b/nand_spl/board/amcc/bamboo/config.mk @@ -0,0 +1,49 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# +# AMCC 440EP Reference Platform (Bamboo) board +# + +# +# TEXT_BASE for SPL: +# +# On 440EP(x) platforms the SPL is located at 0xfffff000...0xffffffff, +# in the last 4kBytes of memory space in cache. +# We will copy this SPL into instruction-cache in start.S. So we set +# TEXT_BASE to starting address in i-cache here. +# +TEXT_BASE = 0x00800000 + +# PAD_TO used to generate a 16kByte binary needed for the combined image +# -> PAD_TO = TEXT_BASE + 0x4000 +PAD_TO = 0x00804000 + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000 +endif diff --git a/nand_spl/board/amcc/bamboo/sdram.c b/nand_spl/board/amcc/bamboo/sdram.c new file mode 100644 index 0000000..4f09072 --- /dev/null +++ b/nand_spl/board/amcc/bamboo/sdram.c @@ -0,0 +1,92 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <ppc4xx.h> +#include <asm/processor.h> +#include <asm/io.h> + +static void wait_init_complete(void) +{ + u32 val; + + do { + mfsdram(mem_mcsts, val); + } while (!(val & 0x80000000)); +} + +/* + * early_sdram_init() + * + * As the name already indicates, this function is called very early + * from start.S and configures the SDRAM with fixed values. This is needed, + * since the 440EP has no internal SRAM and the 4kB NAND_SPL loader has + * not enough free space to implement the complete I2C SPD DDR autodetection + * routines. Therefore the Bamboo only supports the onboard 64MBytes of SDRAM + * when booting from NAND flash. + */ +void early_sdram_init(void) +{ + /* + * Soft-reset SDRAM controller. + */ + mtsdr(sdr_srst, SDR0_SRST_DMC); + mtsdr(sdr_srst, 0x00000000); + + /* + * Disable memory controller. + */ + mtsdram(mem_cfg0, 0x00000000); + + /* + * Setup some default + */ + mtsdram(mem_uabba, 0x00000000); /* ubba=0 (default) */ + mtsdram(mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */ + mtsdram(mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */ + mtsdram(mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */ + mtsdram(mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */ + + /* + * Following for CAS Latency = 2.5 @ 133 MHz PLB + */ + mtsdram(mem_b0cr, 0x00082001); + mtsdram(mem_tr0, 0x41094012); + mtsdram(mem_tr1, 0x8080083d); /* SS=T2 SL=STAGE 3 CD=1 CT=0x00*/ + mtsdram(mem_rtr, 0x04100000); /* Interval 7.8µs @ 133MHz PLB */ + mtsdram(mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM*/ + + /* + * Enable the controller, then wait for DCEN to complete + */ + mtsdram(mem_cfg0, 0x80000000); /* DCEN=1, PMUD=0*/ + wait_init_complete(); +} + +long int initdram(int board_type) +{ + /* + * Nothing to do here, just return size of fixed SDRAM setup + */ + return CFG_MBYTES_SDRAM << 20; +} diff --git a/nand_spl/board/amcc/bamboo/u-boot.lds b/nand_spl/board/amcc/bamboo/u-boot.lds new file mode 100644 index 0000000..28228f8 --- /dev/null +++ b/nand_spl/board/amcc/bamboo/u-boot.lds @@ -0,0 +1,65 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc:common) +SECTIONS +{ + .resetvec 0x00800FFC : + { + *(.resetvec) + } = 0xffff + + .text : + { + start.o (.text) + init.o (.text) + nand_boot.o (.text) + sdram.o (.text) + ndfc.o (.text) + + *(.text) + *(.fixup) + } + _etext = .; + + .data : + { + *(.rodata*) + *(.data*) + *(.sdata*) + __got2_start = .; + *(.got2) + __got2_end = .; + } + + _edata = .; + + __bss_start = .; + .bss : + { + *(.sbss) + *(.bss) + } + + _end = . ; +} |