diff options
39 files changed, 1049 insertions, 229 deletions
diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c index 5617a41..bd65a08 100644 --- a/arch/arm/cpu/armv7/mx6/clock.c +++ b/arch/arm/cpu/armv7/mx6/clock.c @@ -409,20 +409,15 @@ u32 imx_get_uartclk(void) u32 imx_get_fecclk(void) { - return decode_pll(PLL_ENET, MXC_HCLK); + return mxc_get_clock(MXC_IPG_CLK); } -int enable_sata_clock(void) +static int enable_enet_pll(uint32_t en) { - u32 reg = 0; - s32 timeout = 100000; struct mxc_ccm_reg *const imx_ccm = (struct mxc_ccm_reg *) CCM_BASE_ADDR; - - /* Enable sata clock */ - reg = readl(&imx_ccm->CCGR5); /* CCGR5 */ - reg |= MXC_CCM_CCGR5_SATA_MASK; - writel(reg, &imx_ccm->CCGR5); + s32 timeout = 100000; + u32 reg = 0; /* Enable PLLs */ reg = readl(&imx_ccm->analog_pll_enet); @@ -437,10 +432,70 @@ int enable_sata_clock(void) return -EIO; reg &= ~BM_ANADIG_PLL_SYS_BYPASS; writel(reg, &imx_ccm->analog_pll_enet); - reg |= BM_ANADIG_PLL_ENET_ENABLE_SATA; + reg |= en; writel(reg, &imx_ccm->analog_pll_enet); + return 0; +} - return 0 ; +static void ungate_sata_clock(void) +{ + struct mxc_ccm_reg *const imx_ccm = + (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* Enable SATA clock. */ + setbits_le32(&imx_ccm->CCGR5, MXC_CCM_CCGR5_SATA_MASK); +} + +static void ungate_pcie_clock(void) +{ + struct mxc_ccm_reg *const imx_ccm = + (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* Enable PCIe clock. */ + setbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_PCIE_MASK); +} + +int enable_sata_clock(void) +{ + ungate_sata_clock(); + return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA); +} + +int enable_pcie_clock(void) +{ + struct anatop_regs *anatop_regs = + (struct anatop_regs *)ANATOP_BASE_ADDR; + struct mxc_ccm_reg *ccm_regs = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* + * Here be dragons! + * + * The register ANATOP_MISC1 is not documented in the Freescale + * MX6RM. The register that is mapped in the ANATOP space and + * marked as ANATOP_MISC1 is actually documented in the PMU section + * of the datasheet as PMU_MISC1. + * + * Switch LVDS clock source to SATA (0xb), disable clock INPUT and + * enable clock OUTPUT. This is important for PCI express link that + * is clocked from the i.MX6. + */ +#define ANADIG_ANA_MISC1_LVDSCLK1_IBEN (1 << 12) +#define ANADIG_ANA_MISC1_LVDSCLK1_OBEN (1 << 10) +#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK 0x0000001F + clrsetbits_le32(&anatop_regs->ana_misc1, + ANADIG_ANA_MISC1_LVDSCLK1_IBEN | + ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK, + ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb); + + /* PCIe reference clock sourced from AXI. */ + clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL); + + /* Party time! Ungate the clock to the PCIe. */ + ungate_sata_clock(); + ungate_pcie_clock(); + + return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA | + BM_ANADIG_PLL_ENET_ENABLE_PCIE); } unsigned int mxc_get_clock(enum mxc_clock clk) diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index 0208cba..1725279 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -8,6 +8,8 @@ */ #include <common.h> +#include <asm/armv7.h> +#include <asm/pl310.h> #include <asm/errno.h> #include <asm/io.h> #include <asm/arch/imx-regs.h> @@ -41,14 +43,19 @@ u32 get_cpu_rev(void) if (type != MXC_CPU_MX6SL) { reg = readl(&anatop->digprog); + struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; + u32 cfg = readl(&scu->config) & 3; type = ((reg >> 16) & 0xff); if (type == MXC_CPU_MX6DL) { - struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; - u32 cfg = readl(&scu->config) & 3; - if (!cfg) type = MXC_CPU_MX6SOLO; } + + if (type == MXC_CPU_MX6Q) { + if (cfg == 1) + type = MXC_CPU_MX6D; + } + } reg &= 0xff; /* mx6 silicon revision */ return (type << 12) | (reg + 0x10); @@ -62,6 +69,9 @@ u32 __weak get_board_rev(void) if (type == MXC_CPU_MX6SOLO) cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF); + if (type == MXC_CPU_MX6D) + cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF); + return cpurev; } #endif @@ -177,10 +187,41 @@ static void imx_set_wdog_powerdown(bool enable) writew(enable, &wdog2->wmcr); } +static void set_ahb_rate(u32 val) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + u32 reg, div; + + div = get_periph_clk() / val - 1; + reg = readl(&mxc_ccm->cbcdr); + + writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) | + (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr); +} + +static void clear_mmdc_ch_mask(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* Clear MMDC channel mask */ + writel(0, &mxc_ccm->ccdr); +} + int arch_cpu_init(void) { init_aips(); + /* Need to clear MMDC_CHx_MASK to make warm reset work. */ + clear_mmdc_ch_mask(); + + /* + * When low freq boot is enabled, ROM will not set AHB + * freq, so we need to ensure AHB freq is 132MHz in such + * scenario. + */ + if (mxc_get_clock(MXC_ARM_CLK) == 396000000) + set_ahb_rate(132000000); + imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */ #ifdef CONFIG_APBH_DMA @@ -336,3 +377,59 @@ void imx_setup_hdmi(void) writel(reg, &mxc_ccm->chsccdr); } #endif + +#ifndef CONFIG_SYS_L2CACHE_OFF +#define IOMUXC_GPR11_L2CACHE_AS_OCRAM 0x00000002 +void v7_outer_cache_enable(void) +{ + struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE; + unsigned int val; + +#if defined CONFIG_MX6SL + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + val = readl(&iomux->gpr[11]); + if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) { + /* L2 cache configured as OCRAM, reset it */ + val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM; + writel(val, &iomux->gpr[11]); + } +#endif + + writel(0x132, &pl310->pl310_tag_latency_ctrl); + writel(0x132, &pl310->pl310_data_latency_ctrl); + + val = readl(&pl310->pl310_prefetch_ctrl); + + /* Turn on the L2 I/D prefetch */ + val |= 0x30000000; + + /* + * The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0 + * The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2 + * But according to ARM PL310 errata: 752271 + * ID: 752271: Double linefill feature can cause data corruption + * Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2 + * Workaround: The only workaround to this erratum is to disable the + * double linefill feature. This is the default behavior. + */ + +#ifndef CONFIG_MX6Q + val |= 0x40800000; +#endif + writel(val, &pl310->pl310_prefetch_ctrl); + + val = readl(&pl310->pl310_power_ctrl); + val |= L2X0_DYNAMIC_CLK_GATING_EN; + val |= L2X0_STNDBY_MODE_EN; + writel(val, &pl310->pl310_power_ctrl); + + setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN); +} + +void v7_outer_cache_disable(void) +{ + struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE; + + clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN); +} +#endif /* !CONFIG_SYS_L2CACHE_OFF */ diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S index 6c9b11a..5aac773 100644 --- a/arch/arm/cpu/armv7/start.S +++ b/arch/arm/cpu/armv7/start.S @@ -38,12 +38,19 @@ _irq: .word _irq _fiq: .word _fiq _pad: .word 0x12345678 /* now 16*4=64 */ #else +.globl _undefined_instruction _undefined_instruction: .word undefined_instruction +.globl _software_interrupt _software_interrupt: .word software_interrupt +.globl _prefetch_abort _prefetch_abort: .word prefetch_abort +.globl _data_abort _data_abort: .word data_abort +.globl _not_used _not_used: .word not_used +.globl _irq _irq: .word irq +.globl _fiq _fiq: .word fiq _pad: .word 0x12345678 /* now 16*4=64 */ #endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c index 9231649..a77c4de 100644 --- a/arch/arm/imx-common/cpu.c +++ b/arch/arm/imx-common/cpu.c @@ -106,6 +106,8 @@ const char *get_imx_type(u32 imxtype) switch (imxtype) { case MXC_CPU_MX6Q: return "6Q"; /* Quad-core version of the mx6 */ + case MXC_CPU_MX6D: + return "6D"; /* Dual-core version of the mx6 */ case MXC_CPU_MX6DL: return "6DL"; /* Dual Lite version of the mx6 */ case MXC_CPU_MX6SOLO: diff --git a/arch/arm/include/asm/arch-imx/cpu.h b/arch/arm/include/asm/arch-imx/cpu.h new file mode 100644 index 0000000..a35940e --- /dev/null +++ b/arch/arm/include/asm/arch-imx/cpu.h @@ -0,0 +1,13 @@ +/* + * (C) Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#define MXC_CPU_MX51 0x51 +#define MXC_CPU_MX53 0x53 +#define MXC_CPU_MX6SL 0x60 +#define MXC_CPU_MX6DL 0x61 +#define MXC_CPU_MX6SOLO 0x62 +#define MXC_CPU_MX6Q 0x63 +#define MXC_CPU_MX6D 0x64 diff --git a/arch/arm/include/asm/arch-mx5/sys_proto.h b/arch/arm/include/asm/arch-mx5/sys_proto.h index 9949ad1..ac7705b 100644 --- a/arch/arm/include/asm/arch-mx5/sys_proto.h +++ b/arch/arm/include/asm/arch-mx5/sys_proto.h @@ -8,12 +8,7 @@ #ifndef _SYS_PROTO_H_ #define _SYS_PROTO_H_ -#define MXC_CPU_MX51 0x51 -#define MXC_CPU_MX53 0x53 -#define MXC_CPU_MX6SL 0x60 -#define MXC_CPU_MX6DL 0x61 -#define MXC_CPU_MX6SOLO 0x62 -#define MXC_CPU_MX6Q 0x63 +#include "../arch-imx/cpu.h" #define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) u32 get_cpu_rev(void); diff --git a/arch/arm/include/asm/arch-mx6/clock.h b/arch/arm/include/asm/arch-mx6/clock.h index e31ba0a..1b4ded7 100644 --- a/arch/arm/include/asm/arch-mx6/clock.h +++ b/arch/arm/include/asm/arch-mx6/clock.h @@ -55,6 +55,7 @@ unsigned int mxc_get_clock(enum mxc_clock clk); void enable_ocotp_clk(unsigned char enable); void enable_usboh3_clk(unsigned char enable); int enable_sata_clock(void); +int enable_pcie_clock(void); int enable_i2c_clk(unsigned char enable, unsigned i2c_num); void enable_ipu_clock(void); int enable_fec_anatop_clock(enum enet_freq freq); diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h index f2ad6e9..c2d210a 100644 --- a/arch/arm/include/asm/arch-mx6/imx-regs.h +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h @@ -53,6 +53,7 @@ #define GLOBAL_TIMER_BASE_ADDR 0x00A00200 #define PRIVATE_TIMERS_WD_BASE_ADDR 0x00A00600 #define IC_DISTRIBUTOR_BASE_ADDR 0x00A01000 +#define L2_PL310_BASE 0x00A02000 #define GPV0_BASE_ADDR 0x00B00000 #define GPV1_BASE_ADDR 0x00C00000 #define PCIE_ARB_BASE_ADDR 0x01000000 diff --git a/arch/arm/include/asm/arch-mx6/iomux.h b/arch/arm/include/asm/arch-mx6/iomux.h index fe4675e..f9ee0d9 100644 --- a/arch/arm/include/asm/arch-mx6/iomux.h +++ b/arch/arm/include/asm/arch-mx6/iomux.h @@ -15,6 +15,33 @@ #define IOMUXC_GPR1_OTG_ID_ENET_RX_ERR (0<<13) #define IOMUXC_GPR1_OTG_ID_GPIO1 (1<<13) #define IOMUXC_GPR1_OTG_ID_MASK (1<<13) +#define IOMUXC_GPR1_REF_SSP_EN (1 << 16) +#define IOMUXC_GPR1_TEST_POWERDOWN (1 << 18) + +/* + * IOMUXC_GPR8 bit fields + */ +#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_MASK (0x3f << 0) +#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_OFFSET 0 +#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_MASK (0x3f << 6) +#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_OFFSET 6 +#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_MASK (0x3f << 12) +#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_OFFSET 12 +#define IOMUXC_GPR8_PCS_TX_SWING_FULL_MASK (0x7f << 18) +#define IOMUXC_GPR8_PCS_TX_SWING_FULL_OFFSET 18 +#define IOMUXC_GPR8_PCS_TX_SWING_LOW_MASK (0x7f << 25) +#define IOMUXC_GPR8_PCS_TX_SWING_LOW_OFFSET 25 + +/* + * IOMUXC_GPR12 bit fields + */ +#define IOMUXC_GPR12_LOS_LEVEL_9 (0x9 << 4) +#define IOMUXC_GPR12_LOS_LEVEL_MASK (0x1f << 4) +#define IOMUXC_GPR12_APPS_LTSSM_ENABLE (1 << 10) +#define IOMUXC_GPR12_DEVICE_TYPE_EP (0x0 << 12) +#define IOMUXC_GPR12_DEVICE_TYPE_RC (0x2 << 12) +#define IOMUXC_GPR12_DEVICE_TYPE_MASK (0xf << 12) + /* * IOMUXC_GPR13 bit fields */ diff --git a/arch/arm/include/asm/arch-mx6/mx6dl_pins.h b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h index 55cc9ad..2e414ad 100644 --- a/arch/arm/include/asm/arch-mx6/mx6dl_pins.h +++ b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h @@ -647,7 +647,7 @@ MX6_PAD_DECL(ENET_MDIO__ESAI_RX_CLK, 0x05BC, 0x01EC, 2, 0x083C, 0, 0) MX6_PAD_DECL(ENET_MDIO__ENET_1588_EVENT1_OUT, 0x05BC, 0x01EC, 4, 0x0000, 0, 0) MX6_PAD_DECL(ENET_MDIO__GPIO1_IO22, 0x05BC, 0x01EC, 5, 0x0000, 0, 0) MX6_PAD_DECL(ENET_MDIO__SPDIF_LOCK, 0x05BC, 0x01EC, 6, 0x0000, 0, 0) -MX6_PAD_DECL(ENET_REF_CLK__ENET_TX_CLK, 0x05C0, 0x01F0, 1, 0x0000, 0, 0) +MX6_PAD_DECL(ENET_REF_CLK__ENET_TX_CLK, 0x05C0, 0x01F0, 1 | IOMUX_CONFIG_SION, 0x0000, 0, 0) MX6_PAD_DECL(ENET_REF_CLK__ESAI_RX_FS, 0x05C0, 0x01F0, 2, 0x082C, 0, 0) MX6_PAD_DECL(ENET_REF_CLK__GPIO1_IO23, 0x05C0, 0x01F0, 5, 0x0000, 0, 0) MX6_PAD_DECL(ENET_REF_CLK__SPDIF_SR_CLK, 0x05C0, 0x01F0, 6, 0x0000, 0, 0) @@ -695,7 +695,7 @@ MX6_PAD_DECL(GPIO_1__GPIO1_IO01, 0x05E0, 0x0210, 5, 0x0000, 0, 0) MX6_PAD_DECL(GPIO_1__SD1_CD_B, 0x05E0, 0x0210, 6, 0x0000, 0, 0) MX6_PAD_DECL(GPIO_16__ESAI_TX3_RX2, 0x05E4, 0x0214, 0, 0x0850, 1, 0) MX6_PAD_DECL(GPIO_16__ENET_1588_EVENT2_IN, 0x05E4, 0x0214, 1, 0x0000, 0, 0) -MX6_PAD_DECL(GPIO_16__ENET_REF_CLK, 0x05E4, 0x0214, 2, 0x080C, 0, 0) +MX6_PAD_DECL(GPIO_16__ENET_REF_CLK, 0x05E4, 0x0214, 2 | IOMUX_CONFIG_SION, 0x080C, 0, 0) MX6_PAD_DECL(GPIO_16__SD1_LCTL, 0x05E4, 0x0214, 3, 0x0000, 0, 0) MX6_PAD_DECL(GPIO_16__SPDIF_IN, 0x05E4, 0x0214, 4, 0x08F0, 2, 0) MX6_PAD_DECL(GPIO_16__GPIO7_IO11, 0x05E4, 0x0214, 5, 0x0000, 0, 0) @@ -934,7 +934,7 @@ MX6_PAD_DECL(RGMII_TX_CTL__USBOH3_H2_STROBE, 0x06BC, 0x02D4, 0 | IOMUX_CONFIG_SI MX6_PAD_DECL(RGMII_TX_CTL__USB_H2_STROBE, 0x06BC, 0x02D4, 0 | IOMUX_CONFIG_SION, 0x0000, 0, PAD_CTL_PUS_47K_UP) MX6_PAD_DECL(RGMII_TX_CTL__RGMII_TX_CTL, 0x06BC, 0x02D4, 1, 0x0000, 0, 0) MX6_PAD_DECL(RGMII_TX_CTL__GPIO6_IO26, 0x06BC, 0x02D4, 5, 0x0000, 0, 0) -MX6_PAD_DECL(RGMII_TX_CTL__ENET_REF_CLK, 0x06BC, 0x02D4, 7, 0x080C, 1, 0) +MX6_PAD_DECL(RGMII_TX_CTL__ENET_REF_CLK, 0x06BC, 0x02D4, 7 | IOMUX_CONFIG_SION, 0x080C, 1, 0) MX6_PAD_DECL(RGMII_TXC__USB_H2_DATA, 0x06C0, 0x02D8, 0 | IOMUX_CONFIG_SION, 0x0000, 0, 0) MX6_PAD_DECL(RGMII_TXC__RGMII_TXC, 0x06C0, 0x02D8, 1, 0x0000, 0, 0) MX6_PAD_DECL(RGMII_TXC__SPDIF_EXT_CLK, 0x06C0, 0x02D8, 2, 0x08F4, 1, 0) diff --git a/arch/arm/include/asm/arch-mx6/mx6q_pins.h b/arch/arm/include/asm/arch-mx6/mx6q_pins.h index ad31c33..a8456a2 100644 --- a/arch/arm/include/asm/arch-mx6/mx6q_pins.h +++ b/arch/arm/include/asm/arch-mx6/mx6q_pins.h @@ -53,7 +53,7 @@ MX6_PAD_DECL(RGMII_RD0__GPIO6_IO25, 0x0384, 0x0070, 5, 0x0000, 0, 0) MX6_PAD_DECL(RGMII_TX_CTL__USB_H2_STROBE, 0x0388, 0x0074, 0, 0x0000, 0, 0) MX6_PAD_DECL(RGMII_TX_CTL__RGMII_TX_CTL, 0x0388, 0x0074, 1, 0x0000, 0, 0) MX6_PAD_DECL(RGMII_TX_CTL__GPIO6_IO26, 0x0388, 0x0074, 5, 0x0000, 0, 0) -MX6_PAD_DECL(RGMII_TX_CTL__ENET_REF_CLK, 0x0388, 0x0074, 7, 0x083C, 0, 0) +MX6_PAD_DECL(RGMII_TX_CTL__ENET_REF_CLK, 0x0388, 0x0074, 7 | IOMUX_CONFIG_SION, 0x083C, 0, 0) MX6_PAD_DECL(RGMII_RD1__HSI_TX_FLAG, 0x038C, 0x0078, 0, 0x0000, 0, 0) MX6_PAD_DECL(RGMII_RD1__RGMII_RD1, 0x038C, 0x0078, 1, 0x084C, 0, 0) MX6_PAD_DECL(RGMII_RD1__GPIO6_IO27, 0x038C, 0x0078, 5, 0x0000, 0, 0) @@ -523,7 +523,7 @@ MX6_PAD_DECL(ENET_MDIO__ESAI_RX_CLK, 0x04E4, 0x01D0, 2, 0x086C, 0, 0) MX6_PAD_DECL(ENET_MDIO__ENET_1588_EVENT1_OUT, 0x04E4, 0x01D0, 4, 0x0000, 0, 0) MX6_PAD_DECL(ENET_MDIO__GPIO1_IO22, 0x04E4, 0x01D0, 5, 0x0000, 0, 0) MX6_PAD_DECL(ENET_MDIO__SPDIF_LOCK, 0x04E4, 0x01D0, 6, 0x0000, 0, 0) -MX6_PAD_DECL(ENET_REF_CLK__ENET_TX_CLK, 0x04E8, 0x01D4, 1, 0x0000, 0, 0) +MX6_PAD_DECL(ENET_REF_CLK__ENET_TX_CLK, 0x04E8, 0x01D4, 1 | IOMUX_CONFIG_SION, 0x0000, 0, 0) MX6_PAD_DECL(ENET_REF_CLK__ESAI_RX_FS, 0x04E8, 0x01D4, 2, 0x085C, 0, 0) MX6_PAD_DECL(ENET_REF_CLK__GPIO1_IO23, 0x04E8, 0x01D4, 5, 0x0000, 0, 0) MX6_PAD_DECL(ENET_REF_CLK__SPDIF_SR_CLK, 0x04E8, 0x01D4, 6, 0x0000, 0, 0) @@ -703,7 +703,7 @@ MX6_PAD_DECL(GPIO_8__SPDIF_SR_CLK, 0x0614, 0x0244, 6, 0x0000, 0, 0) MX6_PAD_DECL(GPIO_8__USB_OTG_PWR_CTL_WAKE, 0x0614, 0x0244, 7, 0x0000, 0, 0) MX6_PAD_DECL(GPIO_16__ESAI_TX3_RX2, 0x0618, 0x0248, 0, 0x0880, 1, 0) MX6_PAD_DECL(GPIO_16__ENET_1588_EVENT2_IN, 0x0618, 0x0248, 1, 0x0000, 0, 0) -MX6_PAD_DECL(GPIO_16__ENET_REF_CLK, 0x0618, 0x0248, 2, 0x083C, 1, 0) +MX6_PAD_DECL(GPIO_16__ENET_REF_CLK, 0x0618, 0x0248, 2 | IOMUX_CONFIG_SION, 0x083C, 1, 0) MX6_PAD_DECL(GPIO_16__SD1_LCTL, 0x0618, 0x0248, 3, 0x0000, 0, 0) MX6_PAD_DECL(GPIO_16__SPDIF_IN, 0x0618, 0x0248, 4, 0x0914, 3, 0) MX6_PAD_DECL(GPIO_16__GPIO7_IO11, 0x0618, 0x0248, 5, 0x0000, 0, 0) diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h index 17125a6..38851a1 100644 --- a/arch/arm/include/asm/arch-mx6/sys_proto.h +++ b/arch/arm/include/asm/arch-mx6/sys_proto.h @@ -9,13 +9,7 @@ #define _SYS_PROTO_H_ #include <asm/imx-common/regs-common.h> - -#define MXC_CPU_MX51 0x51 -#define MXC_CPU_MX53 0x53 -#define MXC_CPU_MX6SL 0x60 -#define MXC_CPU_MX6DL 0x61 -#define MXC_CPU_MX6SOLO 0x62 -#define MXC_CPU_MX6Q 0x63 +#include "../arch-imx/cpu.h" #define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) u32 get_cpu_rev(void); diff --git a/arch/arm/include/asm/pl310.h b/arch/arm/include/asm/pl310.h index f41ad8c..ddc245b 100644 --- a/arch/arm/include/asm/pl310.h +++ b/arch/arm/include/asm/pl310.h @@ -12,6 +12,9 @@ /* Register bit fields */ #define PL310_AUX_CTRL_ASSOCIATIVITY_MASK (1 << 16) +#define L2X0_DYNAMIC_CLK_GATING_EN (1 << 1) +#define L2X0_STNDBY_MODE_EN (1 << 0) +#define L2X0_CTRL_EN 1 struct pl310_regs { u32 pl310_cache_id; @@ -47,6 +50,24 @@ struct pl310_regs { u32 pad9[1]; u32 pl310_clean_inv_line_idx; u32 pl310_clean_inv_way; + u32 pad10[64]; + u32 pl310_lockdown_dbase; + u32 pl310_lockdown_ibase; + u32 pad11[190]; + u32 pl310_addr_filter_start; + u32 pl310_addr_filter_end; + u32 pad12[190]; + u32 pl310_test_operation; + u32 pad13[3]; + u32 pl310_line_data; + u32 pad14[7]; + u32 pl310_line_tag; + u32 pad15[3]; + u32 pl310_debug_ctrl; + u32 pad16[7]; + u32 pl310_prefetch_ctrl; + u32 pad17[7]; + u32 pl310_power_ctrl; }; void pl310_inval_all(void); diff --git a/board/boundary/nitrogen6x/README b/board/boundary/nitrogen6x/README index 5049093..9d84265 100644 --- a/board/boundary/nitrogen6x/README +++ b/board/boundary/nitrogen6x/README @@ -67,10 +67,10 @@ override auto-detection and force activation of the specified panel. To build U-Boot for one of the Nitrogen6x or SabreLite board: make nitrogen6x_config - make u-boot.imx + make Note that 'nitrogen6x' is a placeholder. The complete list of supported -board configurations is shown in tha MAINTAINERS file: +board configurations is shown in the boards.cfg file: nitrogen6q i.MX6Q/6D 1GB nitrogen6dl i.MX6DL 1GB nitrogen6s i.MX6S 512MB diff --git a/board/boundary/nitrogen6x/nitrogen6dl.cfg b/board/boundary/nitrogen6x/nitrogen6dl.cfg index 97ae0c2..1cdccad 100644 --- a/board/boundary/nitrogen6x/nitrogen6dl.cfg +++ b/board/boundary/nitrogen6x/nitrogen6dl.cfg @@ -16,7 +16,7 @@ IMAGE_VERSION 2 * Boot Device : one of * spi, sd (the board has no nand neither onenand) */ -BOOT_FROM sd +BOOT_FROM spi #define __ASSEMBLY__ #include <config.h> diff --git a/board/boundary/nitrogen6x/nitrogen6dl2g.cfg b/board/boundary/nitrogen6x/nitrogen6dl2g.cfg index 82f837e..516d67e 100644 --- a/board/boundary/nitrogen6x/nitrogen6dl2g.cfg +++ b/board/boundary/nitrogen6x/nitrogen6dl2g.cfg @@ -16,7 +16,7 @@ IMAGE_VERSION 2 * Boot Device : one of * spi, sd (the board has no nand neither onenand) */ -BOOT_FROM sd +BOOT_FROM spi #define __ASSEMBLY__ #include <config.h> diff --git a/board/boundary/nitrogen6x/nitrogen6q.cfg b/board/boundary/nitrogen6x/nitrogen6q.cfg index b6f1518..b6642e6 100644 --- a/board/boundary/nitrogen6x/nitrogen6q.cfg +++ b/board/boundary/nitrogen6x/nitrogen6q.cfg @@ -16,7 +16,7 @@ IMAGE_VERSION 2 * Boot Device : one of * spi, sd (the board has no nand neither onenand) */ -BOOT_FROM sd +BOOT_FROM spi #define __ASSEMBLY__ #include <config.h> diff --git a/board/boundary/nitrogen6x/nitrogen6q2g.cfg b/board/boundary/nitrogen6x/nitrogen6q2g.cfg index 8d7ff25..fe6dfc1 100644 --- a/board/boundary/nitrogen6x/nitrogen6q2g.cfg +++ b/board/boundary/nitrogen6x/nitrogen6q2g.cfg @@ -16,7 +16,7 @@ IMAGE_VERSION 2 * Boot Device : one of * spi, sd (the board has no nand neither onenand) */ -BOOT_FROM sd +BOOT_FROM spi #define __ASSEMBLY__ #include <config.h> diff --git a/board/boundary/nitrogen6x/nitrogen6s.cfg b/board/boundary/nitrogen6x/nitrogen6s.cfg index 34fb9d0..ca30cd6 100644 --- a/board/boundary/nitrogen6x/nitrogen6s.cfg +++ b/board/boundary/nitrogen6x/nitrogen6s.cfg @@ -16,7 +16,7 @@ IMAGE_VERSION 2 * Boot Device : one of * spi, sd (the board has no nand neither onenand) */ -BOOT_FROM sd +BOOT_FROM spi #define __ASSEMBLY__ #include <config.h> diff --git a/board/boundary/nitrogen6x/nitrogen6s1g.cfg b/board/boundary/nitrogen6x/nitrogen6s1g.cfg index d61453c..b1489fb 100644 --- a/board/boundary/nitrogen6x/nitrogen6s1g.cfg +++ b/board/boundary/nitrogen6x/nitrogen6s1g.cfg @@ -16,7 +16,7 @@ IMAGE_VERSION 2 * Boot Device : one of * spi, sd (the board has no nand neither onenand) */ -BOOT_FROM sd +BOOT_FROM spi #define __ASSEMBLY__ #include <config.h> diff --git a/board/freescale/mx6qsabreauto/imximage.cfg b/board/freescale/mx6qsabreauto/imximage.cfg index 6d192a6..16bf473 100644 --- a/board/freescale/mx6qsabreauto/imximage.cfg +++ b/board/freescale/mx6qsabreauto/imximage.cfg @@ -29,119 +29,101 @@ BOOT_FROM sd * Address absolute address of the register * value value to be stored in the register */ +DATA 4 0x020e0798 0x000C0000 +DATA 4 0x020e0758 0x00000000 +DATA 4 0x020e0588 0x00000030 +DATA 4 0x020e0594 0x00000030 +DATA 4 0x020e056c 0x00000030 +DATA 4 0x020e0578 0x00000030 +DATA 4 0x020e074c 0x00000030 +DATA 4 0x020e057c 0x00000030 +DATA 4 0x020e058c 0x00000000 +DATA 4 0x020e059c 0x00000030 +DATA 4 0x020e05a0 0x00000030 +DATA 4 0x020e078c 0x00000030 +DATA 4 0x020e0750 0x00020000 DATA 4 0x020e05a8 0x00000028 DATA 4 0x020e05b0 0x00000028 DATA 4 0x020e0524 0x00000028 DATA 4 0x020e051c 0x00000028 - DATA 4 0x020e0518 0x00000028 DATA 4 0x020e050c 0x00000028 DATA 4 0x020e05b8 0x00000028 DATA 4 0x020e05c0 0x00000028 - -DATA 4 0x020e05ac 0x00000028 -DATA 4 0x020e05b4 0x00000028 -DATA 4 0x020e0528 0x00000028 -DATA 4 0x020e0520 0x00000028 - -DATA 4 0x020e0514 0x00000028 -DATA 4 0x020e0510 0x00000028 -DATA 4 0x020e05bc 0x00000028 -DATA 4 0x020e05c4 0x00000028 - -DATA 4 0x020e056c 0x00000030 -DATA 4 0x020e0578 0x00000030 -DATA 4 0x020e0588 0x00000030 -DATA 4 0x020e0594 0x00000030 - -DATA 4 0x020e057c 0x00000030 -DATA 4 0x020e0590 0x00000030 -DATA 4 0x020e0598 0x00000030 -DATA 4 0x020e058c 0x00000000 - -DATA 4 0x020e059c 0x00003030 -DATA 4 0x020e05a0 0x00003030 +DATA 4 0x020e0774 0x00020000 DATA 4 0x020e0784 0x00000028 DATA 4 0x020e0788 0x00000028 - DATA 4 0x020e0794 0x00000028 DATA 4 0x020e079c 0x00000028 DATA 4 0x020e07a0 0x00000028 DATA 4 0x020e07a4 0x00000028 - DATA 4 0x020e07a8 0x00000028 DATA 4 0x020e0748 0x00000028 -DATA 4 0x020e074c 0x00000030 -DATA 4 0x020e0750 0x00020000 - -DATA 4 0x020e0758 0x00000000 -DATA 4 0x020e0774 0x00020000 -DATA 4 0x020e078c 0x00000030 -DATA 4 0x020e0798 0x000C0000 - +DATA 4 0x020e05ac 0x00000028 +DATA 4 0x020e05b4 0x00000028 +DATA 4 0x020e0528 0x00000028 +DATA 4 0x020e0520 0x00000028 +DATA 4 0x020e0514 0x00000028 +DATA 4 0x020e0510 0x00000028 +DATA 4 0x020e05bc 0x00000028 +DATA 4 0x020e05c4 0x00000028 +DATA 4 0x021b0800 0xa1390003 +DATA 4 0x021b080c 0x001F001F +DATA 4 0x021b0810 0x001F001F +DATA 4 0x021b480c 0x001F001F +DATA 4 0x021b4810 0x001F001F +DATA 4 0x021b083c 0x43260335 +DATA 4 0x021b0840 0x031A030B +DATA 4 0x021b483c 0x4323033B +DATA 4 0x021b4840 0x0323026F +DATA 4 0x021b0848 0x483D4545 +DATA 4 0x021b4848 0x44433E48 +DATA 4 0x021b0850 0x41444840 +DATA 4 0x021b4850 0x4835483E DATA 4 0x021b081c 0x33333333 DATA 4 0x021b0820 0x33333333 DATA 4 0x021b0824 0x33333333 DATA 4 0x021b0828 0x33333333 - DATA 4 0x021b481c 0x33333333 DATA 4 0x021b4820 0x33333333 DATA 4 0x021b4824 0x33333333 DATA 4 0x021b4828 0x33333333 - +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b48b8 0x00000800 +DATA 4 0x021b0004 0x00020036 +DATA 4 0x021b0008 0x09444040 +DATA 4 0x021b000c 0x8A8F7955 +DATA 4 0x021b0010 0xFF328F64 +DATA 4 0x021b0014 0x01FF00DB DATA 4 0x021b0018 0x00001740 - DATA 4 0x021b001c 0x00008000 -DATA 4 0x021b000c 0x8A8F7975 -DATA 4 0x021b0010 0xFF538E64 -DATA 4 0x021b0014 0x01FF00DB -DATA 4 0x021b002c 0x000026D2 - -DATA 4 0x021b0030 0x008F0E21 -DATA 4 0x021b0008 0x09444040 -DATA 4 0x021b0004 0x00020036 +DATA 4 0x021b002c 0x000026d2 +DATA 4 0x021b0030 0x008F1023 DATA 4 0x021b0040 0x00000047 DATA 4 0x021b0000 0x841A0000 - DATA 4 0x021b001c 0x04088032 DATA 4 0x021b001c 0x00008033 -DATA 4 0x021b001c 0x00428031 +DATA 4 0x021b001c 0x00048031 DATA 4 0x021b001c 0x09408030 - DATA 4 0x021b001c 0x04008040 -DATA 4 0x021b0800 0xA1380003 DATA 4 0x021b0020 0x00005800 -DATA 4 0x021b0818 0x00000007 -DATA 4 0x021b4818 0x00000007 - -/* Calibration values based on ARD and 528MHz */ -DATA 4 0x021b083c 0x434B0358 -DATA 4 0x021b0840 0x033D033C -DATA 4 0x021b483c 0x03520362 -DATA 4 0x021b4840 0x03480318 -DATA 4 0x021b0848 0x41383A3C -DATA 4 0x021b4848 0x3F3C374A -DATA 4 0x021b0850 0x42434444 -DATA 4 0x021b4850 0x4932473A - -DATA 4 0x021b080c 0x001F001F -DATA 4 0x021b0810 0x001F001F - -DATA 4 0x021b480c 0x001F001F -DATA 4 0x021b4810 0x001F001F - -DATA 4 0x021b08b8 0x00000800 -DATA 4 0x021b48b8 0x00000800 - -DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b0818 0x00011117 +DATA 4 0x021b4818 0x00011117 DATA 4 0x021b0004 0x00025576 - +DATA 4 0x021b0404 0x00011006 DATA 4 0x021b001c 0x00000000 +/* set the default clock gate to save power */ DATA 4 0x020c4068 0x00C03F3F -DATA 4 0x020c406c 0x0030FC00 +DATA 4 0x020c406c 0x0030FC03 DATA 4 0x020c4070 0x0FFFC000 DATA 4 0x020c4074 0x3FF00000 -DATA 4 0x020c4078 0x00FFF300 -DATA 4 0x020c407c 0x0F0000C3 -DATA 4 0x020c4080 0x000003FF +DATA 4 0x020c4078 0xFFFFF300 +DATA 4 0x020c407c 0x0F0000F3 +DATA 4 0x020c4080 0x00000FFF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4 0x020e0010 0xF00000CF +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ +DATA 4 0x020e0018 0x007F007F +DATA 4 0x020e001c 0x007F007F diff --git a/board/solidrun/hummingboard/hummingboard.c b/board/solidrun/hummingboard/hummingboard.c index 8b309b4..2e2fb2a 100644 --- a/board/solidrun/hummingboard/hummingboard.c +++ b/board/solidrun/hummingboard/hummingboard.c @@ -156,11 +156,7 @@ int board_eth_init(bd_t *bis) setup_iomux_enet(); - ret = cpu_eth_init(bis); - if (ret) - printf("FEC MXC: %s:failed\n", __func__); - - return ret; + return cpu_eth_init(bis); } #endif diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c index 3b2b995..4cefda4 100644 --- a/drivers/net/fec_mxc.c +++ b/drivers/net/fec_mxc.c @@ -128,8 +128,12 @@ static void fec_mii_setspeed(struct ethernet_regs *eth) * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock * and do not drop the Preamble. */ - writel((((imx_get_fecclk() / 1000000) + 2) / 5) << 1, - ð->mii_speed); + register u32 speed = DIV_ROUND_UP(imx_get_fecclk(), 5000000); +#ifdef FEC_QUIRK_ENET_MAC + speed--; +#endif + speed <<= 1; + writel(speed, ð->mii_speed); debug("%s: mii_speed %08x\n", __func__, readl(ð->mii_speed)); } diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile index f0dfb59..e73a498 100644 --- a/drivers/pci/Makefile +++ b/drivers/pci/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_PCI) += pci.o pci_auto.o obj-$(CONFIG_PCI_INDIRECT_BRIDGE) += pci_indirect.o obj-$(CONFIG_PCI_GT64120) += pci_gt64120.o obj-$(CONFIG_PCI_MSC01) += pci_msc01.o +obj-$(CONFIG_PCIE_IMX) += pcie_imx.o obj-$(CONFIG_FTPCI100) += pci_ftpci100.o obj-$(CONFIG_SH4_PCI) += pci_sh4.o obj-$(CONFIG_SH7751_PCI) +=pci_sh7751.o diff --git a/drivers/pci/pcie_imx.c b/drivers/pci/pcie_imx.c new file mode 100644 index 0000000..34377e9 --- /dev/null +++ b/drivers/pci/pcie_imx.c @@ -0,0 +1,606 @@ +/* + * Freescale i.MX6 PCI Express Root-Complex driver + * + * Copyright (C) 2013 Marek Vasut <marex@denx.de> + * + * Based on upstream Linux kernel driver: + * pci-imx6.c: Sean Cross <xobs@kosagi.com> + * pcie-designware.c: Jingoo Han <jg1.han@samsung.com> + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#include <common.h> +#include <pci.h> +#include <asm/arch/clock.h> +#include <asm/arch/iomux.h> +#include <asm/arch/crm_regs.h> +#include <asm/gpio.h> +#include <asm/io.h> +#include <asm/sizes.h> +#include <errno.h> + +#define PCI_ACCESS_READ 0 +#define PCI_ACCESS_WRITE 1 + +#define MX6_DBI_ADDR 0x01ffc000 +#define MX6_DBI_SIZE 0x4000 +#define MX6_IO_ADDR 0x01000000 +#define MX6_IO_SIZE 0x100000 +#define MX6_MEM_ADDR 0x01100000 +#define MX6_MEM_SIZE 0xe00000 +#define MX6_ROOT_ADDR 0x01f00000 +#define MX6_ROOT_SIZE 0xfc000 + +/* PCIe Port Logic registers (memory-mapped) */ +#define PL_OFFSET 0x700 +#define PCIE_PHY_DEBUG_R0 (PL_OFFSET + 0x28) +#define PCIE_PHY_DEBUG_R1 (PL_OFFSET + 0x2c) +#define PCIE_PHY_DEBUG_R1_LINK_UP (1 << 4) +#define PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING (1 << 29) + +#define PCIE_PHY_CTRL (PL_OFFSET + 0x114) +#define PCIE_PHY_CTRL_DATA_LOC 0 +#define PCIE_PHY_CTRL_CAP_ADR_LOC 16 +#define PCIE_PHY_CTRL_CAP_DAT_LOC 17 +#define PCIE_PHY_CTRL_WR_LOC 18 +#define PCIE_PHY_CTRL_RD_LOC 19 + +#define PCIE_PHY_STAT (PL_OFFSET + 0x110) +#define PCIE_PHY_STAT_DATA_LOC 0 +#define PCIE_PHY_STAT_ACK_LOC 16 + +/* PHY registers (not memory-mapped) */ +#define PCIE_PHY_RX_ASIC_OUT 0x100D + +#define PHY_RX_OVRD_IN_LO 0x1005 +#define PHY_RX_OVRD_IN_LO_RX_DATA_EN (1 << 5) +#define PHY_RX_OVRD_IN_LO_RX_PLL_EN (1 << 3) + +/* iATU registers */ +#define PCIE_ATU_VIEWPORT 0x900 +#define PCIE_ATU_REGION_INBOUND (0x1 << 31) +#define PCIE_ATU_REGION_OUTBOUND (0x0 << 31) +#define PCIE_ATU_REGION_INDEX1 (0x1 << 0) +#define PCIE_ATU_REGION_INDEX0 (0x0 << 0) +#define PCIE_ATU_CR1 0x904 +#define PCIE_ATU_TYPE_MEM (0x0 << 0) +#define PCIE_ATU_TYPE_IO (0x2 << 0) +#define PCIE_ATU_TYPE_CFG0 (0x4 << 0) +#define PCIE_ATU_TYPE_CFG1 (0x5 << 0) +#define PCIE_ATU_CR2 0x908 +#define PCIE_ATU_ENABLE (0x1 << 31) +#define PCIE_ATU_BAR_MODE_ENABLE (0x1 << 30) +#define PCIE_ATU_LOWER_BASE 0x90C +#define PCIE_ATU_UPPER_BASE 0x910 +#define PCIE_ATU_LIMIT 0x914 +#define PCIE_ATU_LOWER_TARGET 0x918 +#define PCIE_ATU_BUS(x) (((x) & 0xff) << 24) +#define PCIE_ATU_DEV(x) (((x) & 0x1f) << 19) +#define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16) +#define PCIE_ATU_UPPER_TARGET 0x91C + +/* + * PHY access functions + */ +static int pcie_phy_poll_ack(void __iomem *dbi_base, int exp_val) +{ + u32 val; + u32 max_iterations = 10; + u32 wait_counter = 0; + + do { + val = readl(dbi_base + PCIE_PHY_STAT); + val = (val >> PCIE_PHY_STAT_ACK_LOC) & 0x1; + wait_counter++; + + if (val == exp_val) + return 0; + + udelay(1); + } while (wait_counter < max_iterations); + + return -ETIMEDOUT; +} + +static int pcie_phy_wait_ack(void __iomem *dbi_base, int addr) +{ + u32 val; + int ret; + + val = addr << PCIE_PHY_CTRL_DATA_LOC; + writel(val, dbi_base + PCIE_PHY_CTRL); + + val |= (0x1 << PCIE_PHY_CTRL_CAP_ADR_LOC); + writel(val, dbi_base + PCIE_PHY_CTRL); + + ret = pcie_phy_poll_ack(dbi_base, 1); + if (ret) + return ret; + + val = addr << PCIE_PHY_CTRL_DATA_LOC; + writel(val, dbi_base + PCIE_PHY_CTRL); + + ret = pcie_phy_poll_ack(dbi_base, 0); + if (ret) + return ret; + + return 0; +} + +/* Read from the 16-bit PCIe PHY control registers (not memory-mapped) */ +static int pcie_phy_read(void __iomem *dbi_base, int addr , int *data) +{ + u32 val, phy_ctl; + int ret; + + ret = pcie_phy_wait_ack(dbi_base, addr); + if (ret) + return ret; + + /* assert Read signal */ + phy_ctl = 0x1 << PCIE_PHY_CTRL_RD_LOC; + writel(phy_ctl, dbi_base + PCIE_PHY_CTRL); + + ret = pcie_phy_poll_ack(dbi_base, 1); + if (ret) + return ret; + + val = readl(dbi_base + PCIE_PHY_STAT); + *data = val & 0xffff; + + /* deassert Read signal */ + writel(0x00, dbi_base + PCIE_PHY_CTRL); + + ret = pcie_phy_poll_ack(dbi_base, 0); + if (ret) + return ret; + + return 0; +} + +static int pcie_phy_write(void __iomem *dbi_base, int addr, int data) +{ + u32 var; + int ret; + + /* write addr */ + /* cap addr */ + ret = pcie_phy_wait_ack(dbi_base, addr); + if (ret) + return ret; + + var = data << PCIE_PHY_CTRL_DATA_LOC; + writel(var, dbi_base + PCIE_PHY_CTRL); + + /* capture data */ + var |= (0x1 << PCIE_PHY_CTRL_CAP_DAT_LOC); + writel(var, dbi_base + PCIE_PHY_CTRL); + + ret = pcie_phy_poll_ack(dbi_base, 1); + if (ret) + return ret; + + /* deassert cap data */ + var = data << PCIE_PHY_CTRL_DATA_LOC; + writel(var, dbi_base + PCIE_PHY_CTRL); + + /* wait for ack de-assertion */ + ret = pcie_phy_poll_ack(dbi_base, 0); + if (ret) + return ret; + + /* assert wr signal */ + var = 0x1 << PCIE_PHY_CTRL_WR_LOC; + writel(var, dbi_base + PCIE_PHY_CTRL); + + /* wait for ack */ + ret = pcie_phy_poll_ack(dbi_base, 1); + if (ret) + return ret; + + /* deassert wr signal */ + var = data << PCIE_PHY_CTRL_DATA_LOC; + writel(var, dbi_base + PCIE_PHY_CTRL); + + /* wait for ack de-assertion */ + ret = pcie_phy_poll_ack(dbi_base, 0); + if (ret) + return ret; + + writel(0x0, dbi_base + PCIE_PHY_CTRL); + + return 0; +} + +static int imx6_pcie_link_up(void) +{ + u32 rc, ltssm; + int rx_valid, temp; + + /* link is debug bit 36, debug register 1 starts at bit 32 */ + rc = readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R1); + if ((rc & PCIE_PHY_DEBUG_R1_LINK_UP) && + !(rc & PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING)) + return -EAGAIN; + + /* + * From L0, initiate MAC entry to gen2 if EP/RC supports gen2. + * Wait 2ms (LTSSM timeout is 24ms, PHY lock is ~5us in gen2). + * If (MAC/LTSSM.state == Recovery.RcvrLock) + * && (PHY/rx_valid==0) then pulse PHY/rx_reset. Transition + * to gen2 is stuck + */ + pcie_phy_read((void *)MX6_DBI_ADDR, PCIE_PHY_RX_ASIC_OUT, &rx_valid); + ltssm = readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R0) & 0x3F; + + if (rx_valid & 0x01) + return 0; + + if (ltssm != 0x0d) + return 0; + + printf("transition to gen2 is stuck, reset PHY!\n"); + + pcie_phy_read((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, &temp); + temp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN | PHY_RX_OVRD_IN_LO_RX_PLL_EN); + pcie_phy_write((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, temp); + + udelay(3000); + + pcie_phy_read((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, &temp); + temp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN | PHY_RX_OVRD_IN_LO_RX_PLL_EN); + pcie_phy_write((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, temp); + + return 0; +} + +/* + * iATU region setup + */ +static int imx_pcie_regions_setup(void) +{ + /* + * i.MX6 defines 16MB in the AXI address map for PCIe. + * + * That address space excepted the pcie registers is + * split and defined into different regions by iATU, + * with sizes and offsets as follows: + * + * 0x0100_0000 --- 0x010F_FFFF 1MB IORESOURCE_IO + * 0x0110_0000 --- 0x01EF_FFFF 14MB IORESOURCE_MEM + * 0x01F0_0000 --- 0x01FF_FFFF 1MB Cfg + Registers + */ + + /* CMD reg:I/O space, MEM space, and Bus Master Enable */ + setbits_le32(MX6_DBI_ADDR | PCI_COMMAND, + PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + + /* Set the CLASS_REV of RC CFG header to PCI_CLASS_BRIDGE_PCI */ + setbits_le32(MX6_DBI_ADDR + PCI_CLASS_REVISION, + PCI_CLASS_BRIDGE_PCI << 16); + + /* Region #0 is used for Outbound CFG space access. */ + writel(0, MX6_DBI_ADDR + PCIE_ATU_VIEWPORT); + + writel(MX6_ROOT_ADDR, MX6_DBI_ADDR + PCIE_ATU_LOWER_BASE); + writel(0, MX6_DBI_ADDR + PCIE_ATU_UPPER_BASE); + writel(MX6_ROOT_ADDR + MX6_ROOT_SIZE, MX6_DBI_ADDR + PCIE_ATU_LIMIT); + + writel(0, MX6_DBI_ADDR + PCIE_ATU_LOWER_TARGET); + writel(0, MX6_DBI_ADDR + PCIE_ATU_UPPER_TARGET); + writel(PCIE_ATU_TYPE_CFG0, MX6_DBI_ADDR + PCIE_ATU_CR1); + writel(PCIE_ATU_ENABLE, MX6_DBI_ADDR + PCIE_ATU_CR2); + + return 0; +} + +/* + * PCI Express accessors + */ +static uint32_t get_bus_address(pci_dev_t d, int where) +{ + uint32_t va_address; + + /* Reconfigure Region #0 */ + writel(0, MX6_DBI_ADDR + PCIE_ATU_VIEWPORT); + + if (PCI_BUS(d) < 2) + writel(PCIE_ATU_TYPE_CFG0, MX6_DBI_ADDR + PCIE_ATU_CR1); + else + writel(PCIE_ATU_TYPE_CFG1, MX6_DBI_ADDR + PCIE_ATU_CR1); + + if (PCI_BUS(d) == 0) { + va_address = MX6_DBI_ADDR; + } else { + writel(d << 8, MX6_DBI_ADDR + PCIE_ATU_LOWER_TARGET); + va_address = MX6_IO_ADDR + SZ_16M - SZ_1M; + } + + va_address += (where & ~0x3); + + return va_address; +} + +static int imx_pcie_addr_valid(pci_dev_t d) +{ + if ((PCI_BUS(d) == 0) && (PCI_DEV(d) > 1)) + return -EINVAL; + if ((PCI_BUS(d) == 1) && (PCI_DEV(d) > 0)) + return -EINVAL; + return 0; +} + +/* + * Replace the original ARM DABT handler with a simple jump-back one. + * + * The problem here is that if we have a PCIe bridge attached to this PCIe + * controller, but no PCIe device is connected to the bridges' downstream + * port, the attempt to read/write from/to the config space will produce + * a DABT. This is a behavior of the controller and can not be disabled + * unfortuatelly. + * + * To work around the problem, we backup the current DABT handler address + * and replace it with our own DABT handler, which only bounces right back + * into the code. + */ +static void imx_pcie_fix_dabt_handler(bool set) +{ + extern uint32_t *_data_abort; + uint32_t *data_abort_addr = (uint32_t *)&_data_abort; + + static const uint32_t data_abort_bounce_handler = 0xe25ef004; + uint32_t data_abort_bounce_addr = (uint32_t)&data_abort_bounce_handler; + + static uint32_t data_abort_backup; + + if (set) { + data_abort_backup = *data_abort_addr; + *data_abort_addr = data_abort_bounce_addr; + } else { + *data_abort_addr = data_abort_backup; + } +} + +static int imx_pcie_read_config(struct pci_controller *hose, pci_dev_t d, + int where, u32 *val) +{ + uint32_t va_address; + int ret; + + ret = imx_pcie_addr_valid(d); + if (ret) { + *val = 0xffffffff; + return ret; + } + + va_address = get_bus_address(d, where); + + /* + * Read the PCIe config space. We must replace the DABT handler + * here in case we got data abort from the PCIe controller, see + * imx_pcie_fix_dabt_handler() description. Note that writing the + * "val" with valid value is also imperative here as in case we + * did got DABT, the val would contain random value. + */ + imx_pcie_fix_dabt_handler(true); + writel(0xffffffff, val); + *val = readl(va_address); + imx_pcie_fix_dabt_handler(false); + + return 0; +} + +static int imx_pcie_write_config(struct pci_controller *hose, pci_dev_t d, + int where, u32 val) +{ + uint32_t va_address = 0; + int ret; + + ret = imx_pcie_addr_valid(d); + if (ret) + return ret; + + va_address = get_bus_address(d, where); + + /* + * Write the PCIe config space. We must replace the DABT handler + * here in case we got data abort from the PCIe controller, see + * imx_pcie_fix_dabt_handler() description. + */ + imx_pcie_fix_dabt_handler(true); + writel(val, va_address); + imx_pcie_fix_dabt_handler(false); + + return 0; +} + +/* + * Initial bus setup + */ +static int imx6_pcie_assert_core_reset(void) +{ + struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + + setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN); + clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN); + + return 0; +} + +static int imx6_pcie_init_phy(void) +{ + struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + + clrbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_APPS_LTSSM_ENABLE); + + clrsetbits_le32(&iomuxc_regs->gpr[12], + IOMUXC_GPR12_DEVICE_TYPE_MASK, + IOMUXC_GPR12_DEVICE_TYPE_RC); + clrsetbits_le32(&iomuxc_regs->gpr[12], + IOMUXC_GPR12_LOS_LEVEL_MASK, + IOMUXC_GPR12_LOS_LEVEL_9); + + writel((0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_OFFSET) | + (0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_OFFSET) | + (20 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_OFFSET) | + (127 << IOMUXC_GPR8_PCS_TX_SWING_FULL_OFFSET) | + (127 << IOMUXC_GPR8_PCS_TX_SWING_LOW_OFFSET), + &iomuxc_regs->gpr[8]); + + return 0; +} + +__weak int imx6_pcie_toggle_reset(void) +{ + /* + * See 'PCI EXPRESS BASE SPECIFICATION, REV 3.0, SECTION 6.6.1' + * for detailed understanding of the PCIe CR reset logic. + * + * The PCIe #PERST reset line _MUST_ be connected, otherwise your + * design does not conform to the specification. You must wait at + * least 20 mS after de-asserting the #PERST so the EP device can + * do self-initialisation. + * + * In case your #PERST pin is connected to a plain GPIO pin of the + * CPU, you can define CONFIG_PCIE_IMX_PERST_GPIO in your board's + * configuration file and the condition below will handle the rest + * of the reset toggling. + * + * In case your #PERST toggling logic is more complex, for example + * connected via CPLD or somesuch, you can override this function + * in your board file and implement reset logic as needed. You must + * not forget to wait at least 20 mS after de-asserting #PERST in + * this case either though. + * + * In case your #PERST line of the PCIe EP device is not connected + * at all, your design is broken and you should fix your design, + * otherwise you will observe problems like for example the link + * not coming up after rebooting the system back from running Linux + * that uses the PCIe as well OR the PCIe link might not come up in + * Linux at all in the first place since it's in some non-reset + * state due to being previously used in U-Boot. + */ +#ifdef CONFIG_PCIE_IMX_PERST_GPIO + gpio_direction_output(CONFIG_PCIE_IMX_PERST_GPIO, 0); + mdelay(20); + gpio_set_value(CONFIG_PCIE_IMX_PERST_GPIO, 1); + mdelay(20); +#else + puts("WARNING: Make sure the PCIe #PERST line is connected!\n"); +#endif + return 0; +} + +static int imx6_pcie_deassert_core_reset(void) +{ + struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + + /* FIXME: Power-up GPIO goes here. */ + + /* Enable PCIe */ + clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN); + setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN); + + enable_pcie_clock(); + + /* + * Wait for the clock to settle a bit, when the clock are sourced + * from the CPU, we need about 30mS to settle. + */ + mdelay(50); + + imx6_pcie_toggle_reset(); + + return 0; +} + +static int imx_pcie_link_up(void) +{ + struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + uint32_t tmp; + int count = 0; + + imx6_pcie_assert_core_reset(); + imx6_pcie_init_phy(); + imx6_pcie_deassert_core_reset(); + + imx_pcie_regions_setup(); + + /* + * FIXME: Force the PCIe RC to Gen1 operation + * The RC must be forced into Gen1 mode before bringing the link + * up, otherwise no downstream devices are detected. After the + * link is up, a managed Gen1->Gen2 transition can be initiated. + */ + tmp = readl(MX6_DBI_ADDR + 0x7c); + tmp &= ~0xf; + tmp |= 0x1; + writel(tmp, MX6_DBI_ADDR + 0x7c); + + /* LTSSM enable, starting link. */ + setbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_APPS_LTSSM_ENABLE); + + while (!imx6_pcie_link_up()) { + udelay(10); + count++; + if (count >= 2000) { + debug("phy link never came up\n"); + debug("DEBUG_R0: 0x%08x, DEBUG_R1: 0x%08x\n", + readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R0), + readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R1)); + return -EINVAL; + } + } + + return 0; +} + +void imx_pcie_init(void) +{ + /* Static instance of the controller. */ + static struct pci_controller pcc; + struct pci_controller *hose = &pcc; + int ret; + + memset(&pcc, 0, sizeof(pcc)); + + /* PCI I/O space */ + pci_set_region(&hose->regions[0], + MX6_IO_ADDR, MX6_IO_ADDR, + MX6_IO_SIZE, PCI_REGION_IO); + + /* PCI memory space */ + pci_set_region(&hose->regions[1], + MX6_MEM_ADDR, MX6_MEM_ADDR, + MX6_MEM_SIZE, PCI_REGION_MEM); + + /* System memory space */ + pci_set_region(&hose->regions[2], + MMDC0_ARB_BASE_ADDR, MMDC0_ARB_BASE_ADDR, + 0xefffffff, PCI_REGION_MEM | PCI_REGION_SYS_MEMORY); + + hose->region_count = 3; + + pci_set_ops(hose, + pci_hose_read_config_byte_via_dword, + pci_hose_read_config_word_via_dword, + imx_pcie_read_config, + pci_hose_write_config_byte_via_dword, + pci_hose_write_config_word_via_dword, + imx_pcie_write_config); + + /* Start the controller. */ + ret = imx_pcie_link_up(); + + if (!ret) { + pci_register_hose(hose); + hose->last_busno = pci_hose_scan(hose); + } +} + +/* Probe function. */ +void pci_init_board(void) +{ + imx_pcie_init(); +} diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h index 29a023c..b189bf1 100644 --- a/include/configs/cgtqmx6eval.h +++ b/include/configs/cgtqmx6eval.h @@ -75,7 +75,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ "boot_dir=/boot\0" \ "console=ttymxc1\0" \ @@ -92,24 +92,24 @@ "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \ - "${boot_dir}/${uimage}\0" \ + "loadimage=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \ + "${boot_dir}/${image}\0" \ "loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdt_addr} " \ "${boot_dir}/${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -118,7 +118,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else "\ "echo ERR: Fail to boot from mmc; " \ diff --git a/include/configs/hummingboard.h b/include/configs/hummingboard.h index 4055af5..ac65620 100644 --- a/include/configs/hummingboard.h +++ b/include/configs/hummingboard.h @@ -92,7 +92,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "console=ttymxc0\0" \ "splashpos=m,m\0" \ "fdt_high=0xffffffff\0" \ @@ -124,22 +124,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=${console},${baudrate} " \ "root=/dev/nfs " \ @@ -151,19 +151,19 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -171,7 +171,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/m53evk.h b/include/configs/m53evk.h index a344af4..bd67603 100644 --- a/include/configs/m53evk.h +++ b/include/configs/m53evk.h @@ -39,6 +39,8 @@ #define CONFIG_CMD_USB #define CONFIG_VIDEO +#define CONFIG_REGEX /* Enable regular expression support */ + /* * Memory configurations */ @@ -128,9 +130,9 @@ #define CONFIG_LZO #define CONFIG_MTD_DEVICE #define CONFIG_MTD_PARTITIONS -#define MTDIDS_DEFAULT "nand0=mxc-nand" +#define MTDIDS_DEFAULT "nand0=mxc_nand" #define MTDPARTS_DEFAULT \ - "mtdparts=mxc-nand:" \ + "mtdparts=mxc_nand:" \ "1m(bootloader)ro," \ "512k(environment)," \ "512k(redundant-environment)," \ diff --git a/include/configs/mx23evk.h b/include/configs/mx23evk.h index 1b40a36..b496892 100644 --- a/include/configs/mx23evk.h +++ b/include/configs/mx23evk.h @@ -84,7 +84,7 @@ "fi ; " \ "fi\0" \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "console=ttyAMA0\0" \ "fdt_file=imx23-evk.dtb\0" \ "fdt_addr=0x41000000\0" \ @@ -98,22 +98,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -121,7 +121,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else " \ "echo ERR: Fail to boot from MMC; " \ diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h index 4fd67eb..9b9124a 100644 --- a/include/configs/mx28evk.h +++ b/include/configs/mx28evk.h @@ -198,7 +198,7 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "nand write ${loadaddr} kernel ${filesize}\0" \ "update_nand_fdt=" /* Update fdt */ \ "mtdparts default; " \ @@ -230,10 +230,10 @@ "nand read ${loadaddr} kernel 0x00400000; " \ "if test ${boot_fdt} = yes; then " \ "nand read ${fdt_addr} fdt 0x00080000; " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = no; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo \"ERROR: Set boot_fdt to yes or no.\"; " \ "fi; " \ @@ -248,7 +248,7 @@ "fi ; " \ "fi\0" \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "console_fsl=ttyAM0\0" \ "console_mainline=ttyAMA0\0" \ "fdt_file=imx28-evk.dtb\0" \ @@ -264,22 +264,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=${console_mainline},${baudrate} " \ "root=/dev/nfs " \ @@ -291,19 +291,19 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi;" \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -311,7 +311,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index 1cff171..b389475 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -143,7 +143,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "fdt_file=imx51-babbage.dtb\0" \ "fdt_addr=0x91000000\0" \ "boot_fdt=try\0" \ @@ -157,22 +157,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=ttymxc0,${baudrate} " \ "root=/dev/nfs " \ @@ -184,20 +184,20 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo ERROR: Cannot load the DT; " \ "exit; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -205,7 +205,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h index ae43ea3..77f8567 100644 --- a/include/configs/mx53loco.h +++ b/include/configs/mx53loco.h @@ -103,7 +103,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "fdt_file=imx53-qsb.dtb\0" \ "fdt_addr=0x71000000\0" \ "boot_fdt=try\0" \ @@ -116,22 +116,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=ttymxc0,${baudrate} " \ "root=/dev/nfs " \ @@ -143,20 +143,20 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo ERROR: Cannot load the DT; " \ "exit; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -164,7 +164,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/mx6_common.h b/include/configs/mx6_common.h index 514d634..eb107d3 100644 --- a/include/configs/mx6_common.h +++ b/include/configs/mx6_common.h @@ -22,4 +22,9 @@ #define CONFIG_ARM_ERRATA_751472 #define CONFIG_BOARD_POSTCLK_INIT +#ifndef CONFIG_SYS_L2CACHE_OFF +#define CONFIG_SYS_L2_PL310 +#define CONFIG_SYS_PL310_BASE L2_PL310_BASE +#endif + #endif diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h index f0a82d1..fd651cf 100644 --- a/include/configs/mx6qarm2.h +++ b/include/configs/mx6qarm2.h @@ -72,7 +72,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "console=ttymxc3\0" \ "fdt_high=0xffffffff\0" \ "initrd_high=0xffffffff\0" \ @@ -85,16 +85,16 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ - "bootm\0" \ + "bootz\0" \ "netargs=setenv bootargs console=${console},${baudrate} " \ "root=/dev/nfs " \ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ "netboot=echo Booting from net ...; " \ "run netargs; " \ - "dhcp ${uimage}; bootm\0" \ + "dhcp ${image}; bootz\0" \ #define CONFIG_BOOTCOMMAND \ "mmc dev ${mmcdev};" \ @@ -102,7 +102,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h index 5ee7fa5..4efcebf 100644 --- a/include/configs/mx6sabre_common.h +++ b/include/configs/mx6sabre_common.h @@ -119,7 +119,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ "fdt_addr=0x18000000\0" \ "boot_fdt=try\0" \ @@ -150,22 +150,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=${console},${baudrate} " \ "root=/dev/nfs " \ @@ -177,19 +177,19 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -198,7 +198,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h index b29f78c..e5bdcc2 100644 --- a/include/configs/mx6slevk.h +++ b/include/configs/mx6slevk.h @@ -76,12 +76,12 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "console=ttymxc0\0" \ "fdt_high=0xffffffff\0" \ "initrd_high=0xffffffff\0" \ "fdt_file=imx6sl-evk.dtb\0" \ - "fdt_addr=0x81000000\0" \ + "fdt_addr=0x88000000\0" \ "boot_fdt=try\0" \ "ip_dyn=yes\0" \ "mmcdev=0\0" \ @@ -93,22 +93,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=${console},${baudrate} " \ "root=/dev/nfs " \ @@ -120,19 +120,19 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -141,7 +141,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index e44ec88..ac517ce 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -352,4 +352,15 @@ #define CONFIG_SUPPORT_RAW_INITRD #define CONFIG_CMD_FS_GENERIC +/* + * PCI express + */ +#define CONFIG_CMD_PCI +#ifdef CONFIG_CMD_PCI +#define CONFIG_PCI +#define CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_PCIE_IMX +#endif + #endif /* __CONFIG_H */ diff --git a/include/configs/udoo.h b/include/configs/udoo.h index 614e1fe..7f09489 100644 --- a/include/configs/udoo.h +++ b/include/configs/udoo.h @@ -100,7 +100,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "console=ttymxc1\0" \ "splashpos=m,m\0" \ "fdt_high=0xffffffff\0" \ @@ -132,22 +132,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=${console},${baudrate} " \ "root=/dev/nfs " \ @@ -159,19 +159,19 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -179,7 +179,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ diff --git a/include/configs/vf610twr.h b/include/configs/vf610twr.h index 8d0a00d..500fd2f 100644 --- a/include/configs/vf610twr.h +++ b/include/configs/vf610twr.h @@ -81,7 +81,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "uimage=uImage\0" \ + "image=zImage\0" \ "console=ttyLP1\0" \ "fdt_high=0xffffffff\0" \ "initrd_high=0xffffffff\0" \ @@ -112,22 +112,22 @@ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" \ "netargs=setenv bootargs console=${console},${baudrate} " \ "root=/dev/nfs " \ @@ -139,19 +139,19 @@ "else " \ "setenv get_cmd tftp; " \ "fi; " \ - "${get_cmd} ${uimage}; " \ + "${get_cmd} ${image}; " \ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ "else " \ "if test ${boot_fdt} = try; then " \ - "bootm; " \ + "bootz; " \ "else " \ "echo WARN: Cannot load the DT; " \ "fi; " \ "fi; " \ "else " \ - "bootm; " \ + "bootz; " \ "fi;\0" #define CONFIG_BOOTCOMMAND \ @@ -159,7 +159,7 @@ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ + "if run loadimage; then " \ "run mmcboot; " \ "else run netboot; " \ "fi; " \ |