diff options
-rw-r--r-- | drivers/thermal/imx_thermal.c | 90 |
1 files changed, 84 insertions, 6 deletions
diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c index d90874e..ca35be8 100644 --- a/drivers/thermal/imx_thermal.c +++ b/drivers/thermal/imx_thermal.c @@ -25,6 +25,9 @@ #define FACTOR1 15976 #define FACTOR2 4297157 #define MEASURE_FREQ 327 +#define TEMPERATURE_MIN -40 +#define TEMPERATURE_HOT 85 +#define TEMPERATURE_MAX 125 #define TEMPSENSE0_TEMP_CNT_SHIFT 8 #define TEMPSENSE0_TEMP_CNT_MASK (0xfff << TEMPSENSE0_TEMP_CNT_SHIFT) @@ -41,7 +44,8 @@ struct thermal_data { int maxc; }; -static int read_cpu_temperature_mx6(struct udevice *dev) +#if defined(CONFIG_MX6) +static int read_cpu_temperature(struct udevice *dev) { int temperature; unsigned int reg, n_meas; @@ -123,21 +127,87 @@ static int read_cpu_temperature_mx6(struct udevice *dev) return temperature; } +#elif defined(CONFIG_MX7) +static int read_cpu_temperature(struct udevice *dev) +{ + unsigned int reg, tmp, start; + unsigned int raw_25c, te1; + int temperature; + unsigned int *priv = dev_get_priv(dev); + u32 fuse = *priv; + struct mxc_ccm_anatop_reg *ccm_anatop = (struct mxc_ccm_anatop_reg *) + ANATOP_BASE_ADDR; + /* + * fuse data layout: + * [31:21] sensor value @ 25C + * [20:18] hot temperature value + * [17:9] sensor value of room + * [8:0] sensor value of hot + */ + + raw_25c = fuse >> 21; + if (raw_25c == 0) + raw_25c = 25; + + te1 = (fuse >> 9) & 0x1ff; + + /* + * now we only use single measure, every time we read + * the temperature, we will power on/down anadig thermal + * module + */ + writel(TEMPMON_HW_ANADIG_TEMPSENSE1_POWER_DOWN_MASK, &ccm_anatop->tempsense1_clr); + writel(PMU_REF_REFTOP_SELFBIASOFF_MASK, &ccm_anatop->ref_set); + + /* write measure freq */ + reg = readl(&ccm_anatop->tempsense1); + reg &= ~TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_FREQ_MASK; + reg |= TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_FREQ(MEASURE_FREQ); + writel(reg, &ccm_anatop->tempsense1); + + writel(TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_TEMP_MASK, &ccm_anatop->tempsense1_clr); + writel(TEMPMON_HW_ANADIG_TEMPSENSE1_FINISHED_MASK, &ccm_anatop->tempsense1_clr); + writel(TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_TEMP_MASK, &ccm_anatop->tempsense1_set); + + start = get_timer(0); + /* Wait max 100ms */ + do { + /* + * Since we can not rely on finish bit, use 1ms delay to get + * temperature. From RM, 17us is enough to get data, but + * to gurantee to get the data, delay 100ms here. + */ + reg = readl(&ccm_anatop->tempsense1); + tmp = (reg & TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_MASK) + >> TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_SHIFT; + } while (get_timer(0) < (start + 100)); + + writel(TEMPMON_HW_ANADIG_TEMPSENSE1_FINISHED_MASK, &ccm_anatop->tempsense1_clr); + + /* power down anatop thermal sensor */ + writel(TEMPMON_HW_ANADIG_TEMPSENSE1_POWER_DOWN_MASK, &ccm_anatop->tempsense1_set); + writel(PMU_REF_REFTOP_SELFBIASOFF_MASK, &ccm_anatop->ref_clr); + + /* Single point */ + temperature = tmp - (te1 - raw_25c); + + return temperature; +} +#endif int imx_thermal_get_temp(struct udevice *dev, int *temp) { struct thermal_data *priv = dev_get_priv(dev); int cpu_tmp = 0; - if (is_soc_type(MXC_SOC_MX6)) - cpu_tmp = read_cpu_temperature_mx6(dev); + cpu_tmp = read_cpu_temperature(dev); + while (cpu_tmp >= priv->critical) { printf("CPU Temperature (%dC) too close to max (%dC)", cpu_tmp, priv->maxc); puts(" waiting...\n"); udelay(5000000); - if (is_soc_type(MXC_SOC_MX6)) - cpu_tmp = read_cpu_temperature_mx6(dev); + cpu_tmp = read_cpu_temperature(dev); } *temp = cpu_tmp; @@ -162,9 +232,17 @@ static int imx_thermal_probe(struct udevice *dev) if (is_soc_type(MXC_SOC_MX6)) { /* Check for valid fuse */ if (fuse == 0 || fuse == ~0) { - printf("CPU: Thermal invalid data, fuse: 0x%x\n", fuse); + printf("CPU: Thermal invalid data, fuse: 0x%x\n", + fuse); return -EPERM; } + } else if (is_soc_type(MXC_SOC_MX7)) { + /* No Calibration data in FUSE? */ + if ((fuse & 0x3ffff) == 0) + return -EPERM; + /* We do not support 105C TE2 */ + if (((fuse & 0x1c0000) >> 18) == 0x6) + return -EPERM; } /* set critical cooling temp */ |