summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--doc/device-tree-bindings/spi/soft-spi.txt34
-rw-r--r--drivers/spi/Makefile1
-rw-r--r--drivers/spi/soft_spi.c252
3 files changed, 287 insertions, 0 deletions
diff --git a/doc/device-tree-bindings/spi/soft-spi.txt b/doc/device-tree-bindings/spi/soft-spi.txt
new file mode 100644
index 0000000..d09c1a5
--- /dev/null
+++ b/doc/device-tree-bindings/spi/soft-spi.txt
@@ -0,0 +1,34 @@
+Soft SPI
+
+The soft SPI bus implementation allows the use of GPIO pins to simulate a
+SPI bus. No SPI host is required for this to work. The down-side is that the
+performance will typically be much lower than a real SPI bus.
+
+The soft SPI node requires the following properties:
+
+compatible: "u-boot,soft-spi"
+soft_spi_cs: GPIO number to use for SPI chip select (output)
+soft_spi_sclk: GPIO number to use for SPI clock (output)
+soft_spi_mosi: GPIO number to use for SPI MOSI line (output)
+soft_spi_miso GPIO number to use for SPI MISO line (input)
+spi-delay-us: Number of microseconds of delay between each CS transition
+
+The GPIOs should be specified as required by the GPIO controller referenced.
+The first cell holds the phandle of the controller and the second cell
+typically holds the GPIO number.
+
+
+Example:
+
+ soft-spi {
+ compatible = "u-boot,soft-spi";
+ cs-gpio = <&gpio 235 0>; /* Y43 */
+ sclk-gpio = <&gpio 225 0>; /* Y31 */
+ mosi-gpio = <&gpio 227 0>; /* Y33 */
+ miso-gpio = <&gpio 224 0>; /* Y30 */
+ spi-delay-us = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cs@0 {
+ };
+ };
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 5cc8655..e718528 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -9,6 +9,7 @@
ifdef CONFIG_DM_SPI
obj-y += spi-uclass.o
obj-$(CONFIG_SANDBOX) += spi-emul-uclass.o
+obj-$(CONFIG_SOFT_SPI) += soft_spi.o
else
obj-y += spi.o
obj-$(CONFIG_SOFT_SPI) += soft_spi_legacy.o
diff --git a/drivers/spi/soft_spi.c b/drivers/spi/soft_spi.c
new file mode 100644
index 0000000..5588036
--- /dev/null
+++ b/drivers/spi/soft_spi.c
@@ -0,0 +1,252 @@
+/*
+ * Copyright (c) 2014 Google, Inc
+ *
+ * (C) Copyright 2002
+ * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com.
+ *
+ * Influenced by code from:
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <malloc.h>
+#include <spi.h>
+#include <asm/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct soft_spi_platdata {
+ struct fdt_gpio_state cs;
+ struct fdt_gpio_state sclk;
+ struct fdt_gpio_state mosi;
+ struct fdt_gpio_state miso;
+ int spi_delay_us;
+};
+
+struct soft_spi_priv {
+ unsigned int mode;
+};
+
+static int soft_spi_scl(struct udevice *dev, int bit)
+{
+ struct soft_spi_platdata *plat = dev->platdata;
+ struct soft_spi_priv *priv = dev_get_priv(dev);
+
+ gpio_set_value(plat->sclk.gpio, priv->mode & SPI_CPOL ? bit : !bit);
+
+ return 0;
+}
+
+static int soft_spi_sda(struct udevice *dev, int bit)
+{
+ struct soft_spi_platdata *plat = dev->platdata;
+
+ gpio_set_value(plat->mosi.gpio, bit);
+
+ return 0;
+}
+
+static int soft_spi_cs_activate(struct udevice *dev)
+{
+ struct soft_spi_platdata *plat = dev->platdata;
+ struct soft_spi_priv *priv = dev_get_priv(dev);
+
+ gpio_set_value(plat->cs.gpio, !(priv->mode & SPI_CS_HIGH));
+ gpio_set_value(plat->sclk.gpio, priv->mode & SPI_CPOL);
+ gpio_set_value(plat->cs.gpio, priv->mode & SPI_CS_HIGH);
+
+ return 0;
+}
+
+static int soft_spi_cs_deactivate(struct udevice *dev)
+{
+ struct soft_spi_platdata *plat = dev->platdata;
+ struct soft_spi_priv *priv = dev_get_priv(dev);
+
+ gpio_set_value(plat->cs.gpio, !(priv->mode & SPI_CS_HIGH));
+
+ return 0;
+}
+
+static int soft_spi_claim_bus(struct udevice *dev)
+{
+ /*
+ * Make sure the SPI clock is in idle state as defined for
+ * this slave.
+ */
+ return soft_spi_scl(dev, 0);
+}
+
+static int soft_spi_release_bus(struct udevice *dev)
+{
+ /* Nothing to do */
+ return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * SPI transfer
+ *
+ * This writes "bitlen" bits out the SPI MOSI port and simultaneously clocks
+ * "bitlen" bits in the SPI MISO port. That's just the way SPI works.
+ *
+ * The source of the outgoing bits is the "dout" parameter and the
+ * destination of the input bits is the "din" parameter. Note that "dout"
+ * and "din" can point to the same memory location, in which case the
+ * input data overwrites the output data (since both are buffered by
+ * temporary variables, this is OK).
+ */
+static int soft_spi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct soft_spi_priv *priv = dev_get_priv(dev);
+ struct soft_spi_platdata *plat = dev->platdata;
+ uchar tmpdin = 0;
+ uchar tmpdout = 0;
+ const u8 *txd = dout;
+ u8 *rxd = din;
+ int cpol = priv->mode & SPI_CPOL;
+ int cpha = priv->mode & SPI_CPHA;
+ unsigned int j;
+
+ debug("spi_xfer: slave %s:%s dout %08X din %08X bitlen %u\n",
+ dev->parent->name, dev->name, *(uint *)txd, *(uint *)rxd,
+ bitlen);
+
+ if (flags & SPI_XFER_BEGIN)
+ soft_spi_cs_activate(dev);
+
+ for (j = 0; j < bitlen; j++) {
+ /*
+ * Check if it is time to work on a new byte.
+ */
+ if ((j % 8) == 0) {
+ if (txd)
+ tmpdout = *txd++;
+ else
+ tmpdout = 0;
+ if (j != 0) {
+ if (rxd)
+ *rxd++ = tmpdin;
+ }
+ tmpdin = 0;
+ }
+
+ if (!cpha)
+ soft_spi_scl(dev, !cpol);
+ soft_spi_sda(dev, tmpdout & 0x80);
+ udelay(plat->spi_delay_us);
+ if (cpha)
+ soft_spi_scl(dev, !cpol);
+ else
+ soft_spi_scl(dev, cpol);
+ tmpdin <<= 1;
+ tmpdin |= gpio_get_value(plat->miso.gpio);
+ tmpdout <<= 1;
+ udelay(plat->spi_delay_us);
+ if (cpha)
+ soft_spi_scl(dev, cpol);
+ }
+ /*
+ * If the number of bits isn't a multiple of 8, shift the last
+ * bits over to left-justify them. Then store the last byte
+ * read in.
+ */
+ if (rxd) {
+ if ((bitlen % 8) != 0)
+ tmpdin <<= 8 - (bitlen % 8);
+ *rxd++ = tmpdin;
+ }
+
+ if (flags & SPI_XFER_END)
+ soft_spi_cs_deactivate(dev);
+
+ return 0;
+}
+
+static int soft_spi_set_speed(struct udevice *dev, unsigned int speed)
+{
+ /* Accept any speed */
+ return 0;
+}
+
+static int soft_spi_set_mode(struct udevice *dev, unsigned int mode)
+{
+ struct soft_spi_priv *priv = dev_get_priv(dev);
+
+ priv->mode = mode;
+
+ return 0;
+}
+
+static int soft_spi_child_pre_probe(struct udevice *dev)
+{
+ struct spi_slave *slave = dev_get_parentdata(dev);
+
+ slave->dev = dev;
+ return spi_ofdata_to_platdata(gd->fdt_blob, dev->of_offset, slave);
+}
+
+static const struct dm_spi_ops soft_spi_ops = {
+ .claim_bus = soft_spi_claim_bus,
+ .release_bus = soft_spi_release_bus,
+ .xfer = soft_spi_xfer,
+ .set_speed = soft_spi_set_speed,
+ .set_mode = soft_spi_set_mode,
+};
+
+static int soft_spi_ofdata_to_platdata(struct udevice *dev)
+{
+ struct soft_spi_platdata *plat = dev->platdata;
+ const void *blob = gd->fdt_blob;
+ int node = dev->of_offset;
+
+ if (fdtdec_decode_gpio(blob, node, "cs-gpio", &plat->cs) ||
+ fdtdec_decode_gpio(blob, node, "sclk-gpio", &plat->sclk) ||
+ fdtdec_decode_gpio(blob, node, "mosi-gpio", &plat->mosi) ||
+ fdtdec_decode_gpio(blob, node, "miso-gpio", &plat->miso))
+ return -EINVAL;
+ plat->spi_delay_us = fdtdec_get_int(blob, node, "spi-delay-us", 0);
+
+ return 0;
+}
+
+static int soft_spi_probe(struct udevice *dev)
+{
+ struct spi_slave *slave = dev_get_parentdata(dev);
+ struct soft_spi_platdata *plat = dev->platdata;
+
+ gpio_request(plat->cs.gpio, "soft_spi_cs");
+ gpio_request(plat->sclk.gpio, "soft_spi_sclk");
+ gpio_request(plat->mosi.gpio, "soft_spi_mosi");
+ gpio_request(plat->miso.gpio, "soft_spi_miso");
+
+ gpio_direction_output(plat->sclk.gpio, slave->mode & SPI_CPOL);
+ gpio_direction_output(plat->mosi.gpio, 1);
+ gpio_direction_input(plat->miso.gpio);
+ gpio_direction_output(plat->cs.gpio, !(slave->mode & SPI_CS_HIGH));
+
+ return 0;
+}
+
+static const struct udevice_id soft_spi_ids[] = {
+ { .compatible = "u-boot,soft-spi" },
+ { }
+};
+
+U_BOOT_DRIVER(soft_spi) = {
+ .name = "soft_spi",
+ .id = UCLASS_SPI,
+ .of_match = soft_spi_ids,
+ .ops = &soft_spi_ops,
+ .ofdata_to_platdata = soft_spi_ofdata_to_platdata,
+ .platdata_auto_alloc_size = sizeof(struct soft_spi_platdata),
+ .priv_auto_alloc_size = sizeof(struct soft_spi_priv),
+ .per_child_auto_alloc_size = sizeof(struct spi_slave),
+ .probe = soft_spi_probe,
+ .child_pre_probe = soft_spi_child_pre_probe,
+};