diff options
| -rw-r--r-- | drivers/mtd/nand/Kconfig | 15 | ||||
| -rw-r--r-- | drivers/mtd/nand/vf610_nfc.c | 40 |
2 files changed, 50 insertions, 5 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 0a9e96f..3024357 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -41,6 +41,21 @@ config NAND_VF610_NFC The driver supports a maximum 2k page size. The driver currently does not support hardware ECC. +choice + prompt "Hardware ECC strength" + depends on NAND_VF610_NFC + default SYS_NAND_VF610_NFC_45_ECC_BYTES + help + Select the ECC strength used in the hardware BCH ECC block. + +config SYS_NAND_VF610_NFC_45_ECC_BYTES + bool "24-error correction (45 ECC bytes)" + +config SYS_NAND_VF610_NFC_60_ECC_BYTES + bool "32-error correction (60 ECC bytes)" + +endchoice + comment "Generic NAND options" # Enhance depends when converting drivers to Kconfig which use this config diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/vf610_nfc.c index 05cbdf3..2c02ff5 100644 --- a/drivers/mtd/nand/vf610_nfc.c +++ b/drivers/mtd/nand/vf610_nfc.c @@ -71,6 +71,7 @@ /* NFC ECC mode define */ #define ECC_BYPASS 0 #define ECC_45_BYTE 6 +#define ECC_60_BYTE 7 /*** Register Mask and bit definitions */ @@ -155,7 +156,10 @@ struct vf610_nfc { #define mtd_to_nfc(_mtd) \ (struct vf610_nfc *)((struct nand_chip *)_mtd->priv)->priv -static struct nand_ecclayout vf610_nfc_ecc45 = { +#if defined(CONFIG_SYS_NAND_VF610_NFC_45_ECC_BYTES) +#define ECC_HW_MODE ECC_45_BYTE + +static struct nand_ecclayout vf610_nfc_ecc = { .eccbytes = 45, .eccpos = {19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, @@ -167,6 +171,24 @@ static struct nand_ecclayout vf610_nfc_ecc45 = { {.offset = 8, .length = 11} } }; +#elif defined(CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES) +#define ECC_HW_MODE ECC_60_BYTE + +static struct nand_ecclayout vf610_nfc_ecc = { + .eccbytes = 60, + .eccpos = { 4, 5, 6, 7, 8, 9, 10, 11, + 12, 13, 14, 15, 16, 17, 18, 19, + 20, 21, 22, 23, 24, 25, 26, 27, + 28, 29, 30, 31, 32, 33, 34, 35, + 36, 37, 38, 39, 40, 41, 42, 43, + 44, 45, 46, 47, 48, 49, 50, 51, + 52, 53, 54, 55, 56, 57, 58, 59, + 60, 61, 62, 63 }, + .oobfree = { + {.offset = 2, + .length = 2} } +}; +#endif static inline u32 vf610_nfc_read(struct mtd_info *mtd, uint reg) { @@ -340,7 +362,7 @@ static void vf610_nfc_command(struct mtd_info *mtd, unsigned command, vf610_nfc_transfer_size(nfc->regs, page_sz); vf610_nfc_send_commands(nfc->regs, NAND_CMD_SEQIN, command, PROGRAM_PAGE_CMD_CODE); - vf610_nfc_ecc_mode(mtd, ECC_45_BYTE); + vf610_nfc_ecc_mode(mtd, ECC_HW_MODE); break; case NAND_CMD_RESET: @@ -365,7 +387,7 @@ static void vf610_nfc_command(struct mtd_info *mtd, unsigned command, vf610_nfc_send_commands(nfc->regs, NAND_CMD_READ0, NAND_CMD_READSTART, READ_PAGE_CMD_CODE); vf610_nfc_addr_cycle(mtd, column, page); - vf610_nfc_ecc_mode(mtd, ECC_45_BYTE); + vf610_nfc_ecc_mode(mtd, ECC_HW_MODE); break; case NAND_CMD_ERASE1: @@ -645,7 +667,9 @@ static int vf610_nfc_nand_init(int devnum, void __iomem *addr) goto error; } - chip->ecc.layout = &vf610_nfc_ecc45; + /* Current HW ECC layouts only use 64 bytes of OOB */ + if (mtd->oobsize > 64) + mtd->oobsize = 64; /* propagate ecc.layout to mtd_info */ mtd->ecclayout = chip->ecc.layout; @@ -653,9 +677,15 @@ static int vf610_nfc_nand_init(int devnum, void __iomem *addr) chip->ecc.write_page = vf610_nfc_write_page; chip->ecc.mode = NAND_ECC_HW; - chip->ecc.bytes = 45; chip->ecc.size = PAGE_2K; + chip->ecc.layout = &vf610_nfc_ecc; +#if defined(CONFIG_SYS_NAND_VF610_NFC_45_ECC_BYTES) chip->ecc.strength = 24; + chip->ecc.bytes = 45; +#elif defined(CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES) + chip->ecc.strength = 32; + chip->ecc.bytes = 60; +#endif /* Enable ECC_STATUS */ vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_ECC_SRAM_REQ_BIT); |