diff options
56 files changed, 2251 insertions, 342 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 54d075b..07541bd 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1037,6 +1037,7 @@ Mark Jonas <mark.jonas@de.bosch.com> Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> MS7720SE SH7720 + R0P77570030RL SH7757 R0P77850011RL SH7785 ######################################################################### @@ -892,6 +892,18 @@ The following options need to be configured: automatically converts one 32 bit word to two 16 bit words you may also try CONFIG_SMC911X_32_BIT. + CONFIG_SH_ETHER + Support for Renesas on-chip Ethernet controller + + CONFIG_SH_ETHER_USE_PORT + Define the number of ports to be used + + CONFIG_SH_ETHER_PHY_ADDR + Define the ETH PHY's address + + CONFIG_SH_ETHER_CACHE_WRITEBACK + If this option is set, the driver enables cache flush. + - USB Support: At the moment only the UHCI host controller is supported (PIP405, MIP405, MPC5200); define @@ -1648,6 +1660,11 @@ The following options need to be configured: SPI EEPROM, also an instance works with Crystal A/D and D/As on the SACSng board) + CONFIG_SH_SPI + + Enables the driver for SPI controller on SuperH. Currently + only SH7757 is supported. + CONFIG_SPI_X Enables extended (16-bit) SPI EEPROM addressing. diff --git a/arch/powerpc/cpu/mpc83xx/pcie.c b/arch/powerpc/cpu/mpc83xx/pcie.c index 46a706d..52d4461 100644 --- a/arch/powerpc/cpu/mpc83xx/pcie.c +++ b/arch/powerpc/cpu/mpc83xx/pcie.c @@ -48,11 +48,26 @@ static struct { #ifdef CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES +/* private structure for mpc83xx pcie hose */ +static struct mpc83xx_pcie_priv { + u8 index; +} pcie_priv[PCIE_MAX_BUSES] = { + { + /* pcie controller 1 */ + .index = 0, + }, + { + /* pcie controller 2 */ + .index = 1, + }, +}; + static int mpc83xx_pcie_remap_cfg(struct pci_controller *hose, pci_dev_t dev) { int bus = PCI_BUS(dev) - hose->first_busno; immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; - pex83xx_t *pex = &immr->pciexp[bus]; + struct mpc83xx_pcie_priv *pcie_priv = hose->priv_data; + pex83xx_t *pex = &immr->pciexp[pcie_priv->index]; struct pex_outbound_window *out_win = &pex->bridge.pex_outbound_win[0]; u8 devfn = PCI_DEV(dev) << 3 | PCI_FUNC(dev); u32 dev_base = bus << 24 | devfn << 16; @@ -142,6 +157,8 @@ static void mpc83xx_pcie_register_hose(int bus, struct pci_region *reg, hose->cfg_addr = (unsigned int *)mpc83xx_pcie_cfg_space[bus].base; + hose->priv_data = &pcie_priv[bus]; + pci_set_ops(hose, pcie_read_config_byte, pcie_read_config_word, diff --git a/arch/powerpc/cpu/mpc83xx/speed.c b/arch/powerpc/cpu/mpc83xx/speed.c index 93e9f1c..5e616dd 100644 --- a/arch/powerpc/cpu/mpc83xx/speed.c +++ b/arch/powerpc/cpu/mpc83xx/speed.c @@ -161,7 +161,7 @@ int get_clocks(void) #endif } - spmf = ((im->reset.rcwl & HRCWL_SPMF) >> HRCWL_SPMF_SHIFT); + spmf = (im->clk.spmr & SPMR_SPMF) >> SPMR_SPMF_SHIFT; csb_clk = pci_sync_in * (1 + clkin_div) * spmf; sccr = im->clk.sccr; @@ -392,7 +392,7 @@ int get_clocks(void) #endif lbiu_clk = csb_clk * - (1 + ((im->reset.rcwl & HRCWL_LBIUCM) >> HRCWL_LBIUCM_SHIFT)); + (1 + ((im->clk.spmr & SPMR_LBIUCM) >> SPMR_LBIUCM_SHIFT)); lcrr = (im->im_lbc.lcrr & LCRR_CLKDIV) >> LCRR_CLKDIV_SHIFT; switch (lcrr) { case 2: @@ -406,11 +406,12 @@ int get_clocks(void) } mem_clk = csb_clk * - (1 + ((im->reset.rcwl & HRCWL_DDRCM) >> HRCWL_DDRCM_SHIFT)); - corepll = (im->reset.rcwl & HRCWL_COREPLL) >> HRCWL_COREPLL_SHIFT; + (1 + ((im->clk.spmr & SPMR_DDRCM) >> SPMR_DDRCM_SHIFT)); + corepll = (im->clk.spmr & SPMR_COREPLL) >> SPMR_COREPLL_SHIFT; + #if defined(CONFIG_MPC8360) mem_sec_clk = csb_clk * (1 + - ((im->reset.rcwl & HRCWL_LBIUCM) >> HRCWL_LBIUCM_SHIFT)); + ((im->clk.spmr & SPMR_LBIUCM) >> SPMR_LBIUCM_SHIFT)); #endif corecnf_tab_index = ((corepll & 0x1F) << 2) | ((corepll & 0x60) >> 5); @@ -442,8 +443,8 @@ int get_clocks(void) } #if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832x) - qepmf = (im->reset.rcwl & HRCWL_CEPMF) >> HRCWL_CEPMF_SHIFT; - qepdf = (im->reset.rcwl & HRCWL_CEPDF) >> HRCWL_CEPDF_SHIFT; + qepmf = (im->clk.spmr & SPMR_CEPMF) >> SPMR_CEPMF_SHIFT; + qepdf = (im->clk.spmr & SPMR_CEPDF) >> SPMR_CEPDF_SHIFT; qe_clk = (pci_sync_in * qepmf) / (1 + qepdf); brg_clk = qe_clk / 2; #endif diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile index b7f51e7..cbb0fc6 100644 --- a/arch/powerpc/cpu/mpc85xx/Makefile +++ b/arch/powerpc/cpu/mpc85xx/Makefile @@ -89,7 +89,7 @@ COBJS-$(CONFIG_MPC8569) += mpc8569_serdes.o COBJS-$(CONFIG_MPC8572) += mpc8572_serdes.o COBJS-$(CONFIG_P1011) += p1021_serdes.o COBJS-$(CONFIG_P1012) += p1021_serdes.o -COBJS-$(CONFIG_P1013) += p1013_serdes.o +COBJS-$(CONFIG_P1013) += p1022_serdes.o COBJS-$(CONFIG_P1020) += p1021_serdes.o COBJS-$(CONFIG_P1021) += p1021_serdes.o COBJS-$(CONFIG_P1022) += p1022_serdes.o diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c index 0cc8b1e..e94975a 100644 --- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c +++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c @@ -59,6 +59,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) #if defined(CONFIG_SYS_FSL_ERRATUM_ESDHC136) puts("Work-around for Erratum ESDHC136 enabled\n"); #endif +#if defined(CONFIG_SYS_FSL_ERRATUM_ESDHC_A001) + puts("Work-around for Erratum ESDHC-A001 enabled\n"); +#endif #ifdef CONFIG_SYS_FSL_ERRATUM_CPC_A002 puts("Work-around for Erratum CPC-A002 enabled\n"); #endif @@ -71,7 +74,13 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) #ifdef CONFIG_SYS_FSL_ERRATUM_DDR_A003 puts("Work-around for Erratum DDR-A003 enabled\n"); #endif - +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR_115 + puts("Work-around for Erratum DDR115 enabled\n"); +#endif +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + puts("Work-around for Erratum DDR111 enabled\n"); + puts("Work-around for Erratum DDR134 enabled\n"); +#endif return 0; } diff --git a/arch/powerpc/cpu/mpc85xx/ddr-gen3.c b/arch/powerpc/cpu/mpc85xx/ddr-gen3.c index fa7e09f..73b320b 100644 --- a/arch/powerpc/cpu/mpc85xx/ddr-gen3.c +++ b/arch/powerpc/cpu/mpc85xx/ddr-gen3.c @@ -21,6 +21,10 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, unsigned int i; volatile ccsr_ddr_t *ddr; u32 temp_sdram_cfg; +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + volatile ccsr_local_ecm_t *ecm = (void *)CONFIG_SYS_MPC85xx_ECM_ADDR; + u32 total_gb_size_per_controller; +#endif switch (ctrl_num) { case 0: @@ -178,13 +182,33 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, * when operatiing in 32-bit bus mode with 4-beat bursts, * This erratum does not affect DDR3 mode, only for DDR2 mode. */ -#ifdef CONFIG_MPC8572 +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR_115 if ((((in_be32(&ddr->sdram_cfg) >> 24) & 0x7) == SDRAM_TYPE_DDR2) && in_be32(&ddr->sdram_cfg) & 0x80000) { /* set DEBUG_1[31] */ setbits_be32(&ddr->debug[0], 1); } #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + /* + * This is the combined workaround for DDR111 and DDR134 + * following the published errata for MPC8572 + */ + + /* 1. Set EEBACR[3] */ + setbits_be32(&ecm->eebacr, 0x10000000); + debug("Setting EEBACR[3] to 0x%08x\n", in_be32(&ecm->eebacr)); + + /* 2. Set DINIT in SDRAM_CFG_2*/ + setbits_be32(&ddr->sdram_cfg_2, SDRAM_CFG2_D_INIT); + debug("Setting sdram_cfg_2[D_INIT] to 0x%08x\n", + in_be32(&ddr->sdram_cfg_2)); + + /* 3. Set DEBUG_3[21] */ + setbits_be32(&ddr->debug[2], 0x400); + debug("Setting DEBUG_3[21] to 0x%08x\n", in_be32(&ddr->debug[2])); + +#endif /* part 1 of the workaound */ /* * 500 painful micro-seconds must elapse between @@ -199,11 +223,90 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, temp_sdram_cfg = in_be32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI; out_be32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN); asm volatile("sync;isync"); - while (!(in_be32(&ddr->debug[1]) & 0x2)) - ; /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */ - while (in_be32(&ddr->sdram_cfg_2) & 0x10) { + while (in_be32(&ddr->sdram_cfg_2) & SDRAM_CFG2_D_INIT) udelay(10000); /* throttle polling rate */ + +#ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 + /* continue this workaround */ + + /* 4. Clear DEBUG3[21] */ + clrbits_be32(&ddr->debug[2], 0x400); + debug("Clearing D3[21] to 0x%08x\n", in_be32(&ddr->debug[2])); + + /* DDR134 workaround starts */ + /* A: Clear sdram_cfg_2[odt_cfg] */ + clrbits_be32(&ddr->sdram_cfg_2, SDRAM_CFG2_ODT_CFG_MASK); + debug("Clearing SDRAM_CFG2[ODT_CFG] to 0x%08x\n", + in_be32(&ddr->sdram_cfg_2)); + + /* B: Set DEBUG1[15] */ + setbits_be32(&ddr->debug[0], 0x10000); + debug("Setting D1[15] to 0x%08x\n", in_be32(&ddr->debug[0])); + + /* C: Set timing_cfg_2[cpo] to 0b11111 */ + setbits_be32(&ddr->timing_cfg_2, TIMING_CFG_2_CPO_MASK); + debug("Setting TMING_CFG_2[CPO] to 0x%08x\n", + in_be32(&ddr->timing_cfg_2)); + + /* D: Set D6 to 0x9f9f9f9f */ + out_be32(&ddr->debug[5], 0x9f9f9f9f); + debug("Setting D6 to 0x%08x\n", in_be32(&ddr->debug[5])); + + /* E: Set D7 to 0x9f9f9f9f */ + out_be32(&ddr->debug[6], 0x9f9f9f9f); + debug("Setting D7 to 0x%08x\n", in_be32(&ddr->debug[6])); + + /* F: Set D2[20] */ + setbits_be32(&ddr->debug[1], 0x800); + debug("Setting D2[20] to 0x%08x\n", in_be32(&ddr->debug[1])); + + /* G: Poll on D2[20] until cleared */ + while (in_be32(&ddr->debug[1]) & 0x800) + udelay(10000); /* throttle polling rate */ + + /* H: Clear D1[15] */ + clrbits_be32(&ddr->debug[0], 0x10000); + debug("Setting D1[15] to 0x%08x\n", in_be32(&ddr->debug[0])); + + /* I: Set sdram_cfg_2[odt_cfg] */ + setbits_be32(&ddr->sdram_cfg_2, + regs->ddr_sdram_cfg_2 & SDRAM_CFG2_ODT_CFG_MASK); + debug("Setting sdram_cfg_2 to 0x%08x\n", in_be32(&ddr->sdram_cfg_2)); + + /* Continuing with the DDR111 workaround */ + /* 5. Set D2[21] */ + setbits_be32(&ddr->debug[1], 0x400); + debug("Setting D2[21] to 0x%08x\n", in_be32(&ddr->debug[1])); + + /* 6. Poll D2[21] until its cleared */ + while (in_be32(&ddr->debug[1]) & 0x400) + udelay(10000); /* throttle polling rate */ + + /* 7. Wait for 400ms/GB */ + total_gb_size_per_controller = 0; + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + total_gb_size_per_controller += + ((regs->cs[i].bnds & 0xFFFF) >> 6) + - (regs->cs[i].bnds >> 22) + 1; } + if (in_be32(&ddr->sdram_cfg) & 0x80000) + total_gb_size_per_controller <<= 1; + debug("Wait for %d ms\n", total_gb_size_per_controller * 400); + udelay(total_gb_size_per_controller * 400000); + + /* 8. Set sdram_cfg_2[dinit] if options requires */ + setbits_be32(&ddr->sdram_cfg_2, + regs->ddr_sdram_cfg_2 & SDRAM_CFG2_D_INIT); + debug("Setting sdram_cfg_2 to 0x%08x\n", in_be32(&ddr->sdram_cfg_2)); + + /* 9. Poll until dinit is cleared */ + while (in_be32(&ddr->sdram_cfg_2) & SDRAM_CFG2_D_INIT) + udelay(10000); + + /* 10. Clear EEBACR[3] */ + clrbits_be32(&ecm->eebacr, 10000000); + debug("Clearing EEBACR[3] to 0x%08x\n", in_be32(&ecm->eebacr)); +#endif /* CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 */ } diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 36464aa..3a29d1c 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -77,6 +77,8 @@ #define CONFIG_MAX_CPUS 2 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_FSL_ERRATUM_DDR_115 +#define CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134 #elif defined(CONFIG_P1010) #define CONFIG_MAX_CPUS 1 @@ -130,11 +132,15 @@ #define CONFIG_MAX_CPUS 1 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 #elif defined(CONFIG_P2020) #define CONFIG_MAX_CPUS 2 #define CONFIG_SYS_FSL_NUM_LAWS 12 #define CONFIG_SYS_FSL_SEC_COMPAT 2 +#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 +#define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 #elif defined(CONFIG_PPC_P2040) #define CONFIG_MAX_CPUS 4 diff --git a/arch/powerpc/include/asm/fsl_ddr_sdram.h b/arch/powerpc/include/asm/fsl_ddr_sdram.h index 852e5c3..02a1f5d 100644 --- a/arch/powerpc/include/asm/fsl_ddr_sdram.h +++ b/arch/powerpc/include/asm/fsl_ddr_sdram.h @@ -89,6 +89,11 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t; #define SDRAM_CFG_2T_EN 0x00008000 #define SDRAM_CFG_BI 0x00000001 +#define SDRAM_CFG2_D_INIT 0x00000010 +#define SDRAM_CFG2_ODT_CFG_MASK 0x00600000 + +#define TIMING_CFG_2_CPO_MASK 0x0F800000 + #if defined(CONFIG_P4080) #define RD_TO_PRE_MASK 0xf #define RD_TO_PRE_SHIFT 13 diff --git a/arch/sh/config.mk b/arch/sh/config.mk index 4ef85e3..433cc15 100644 --- a/arch/sh/config.mk +++ b/arch/sh/config.mk @@ -31,4 +31,10 @@ endif PLATFORM_CPPFLAGS += -DCONFIG_SH -D__SH__ PLATFORM_LDFLAGS += -e $(CONFIG_SYS_TEXT_BASE) --defsym reloc_dst=$(CONFIG_SYS_TEXT_BASE) LDFLAGS_u-boot = --gc-sections + +ifdef CONFIG_SYS_LDSCRIPT +LDSCRIPT := $(subst ",,$(CONFIG_SYS_LDSCRIPT)) +else LDSCRIPT := $(SRCTREE)/$(CPUDIR)/u-boot.lds +endif + diff --git a/arch/sh/include/asm/cpu_sh4.h b/arch/sh/include/asm/cpu_sh4.h index fdcebd6..9b29d3a 100644 --- a/arch/sh/include/asm/cpu_sh4.h +++ b/arch/sh/include/asm/cpu_sh4.h @@ -44,6 +44,8 @@ # include <asm/cpu_sh7722.h> #elif defined (CONFIG_CPU_SH7723) # include <asm/cpu_sh7723.h> +#elif defined (CONFIG_CPU_SH7757) +# include <asm/cpu_sh7757.h> #elif defined (CONFIG_CPU_SH7763) # include <asm/cpu_sh7763.h> #elif defined (CONFIG_CPU_SH7780) diff --git a/arch/sh/include/asm/cpu_sh7757.h b/arch/sh/include/asm/cpu_sh7757.h new file mode 100644 index 0000000..17a6537 --- /dev/null +++ b/arch/sh/include/asm/cpu_sh7757.h @@ -0,0 +1,218 @@ +/* + * Copyright (C) 2011 Renesas Solutions Corp. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#ifndef _ASM_CPU_SH7757_H_ +#define _ASM_CPU_SH7757_H_ + +#define CCR 0xFF00001C +#define WTCNT 0xFFCC0000 +#define CCR_CACHE_INIT 0x0000090b +#define CACHE_OC_NUM_WAYS 1 + +#ifndef __ASSEMBLY__ /* put C only stuff in this section */ +/* MMU */ +struct mmu_regs { + unsigned int reserved[4]; + unsigned int mmucr; +}; +#define MMU_BASE ((struct mmu_regs *)0xff000000) + +/* Watchdog */ +#define WTCSR0 0xffcc0002 +#define WRSTCSR_R 0xffcc0003 +#define WRSTCSR_W 0xffcc0002 +#define WTCSR_PREFIX 0xa500 +#define WRSTCSR_PREFIX 0x6900 +#define WRSTCSR_WOVF_PREFIX 0x9600 + +/* SCIF */ +#define SCIF0_BASE 0xfe4b0000 /* The real name is SCIF2 */ +#define SCIF1_BASE 0xfe4c0000 /* The real name is SCIF3 */ +#define SCIF2_BASE 0xfe4d0000 /* The real name is SCIF4 */ + +/* SerMux */ +#define SMR0 0xfe470000 + +/* TMU0 */ +#define TSTR 0xFE430004 +#define TOCR 0xFE430000 +#define TSTR0 0xFE430004 +#define TCOR0 0xFE430008 +#define TCNT0 0xFE43000C +#define TCR0 0xFE430010 +#define TCOR1 0xFE430014 +#define TCNT1 0xFE430018 +#define TCR1 0xFE43001C +#define TCOR2 0xFE430020 +#define TCNT2 0xFE430024 +#define TCR2 0xFE430028 +#define TCPR2 0xFE43002C + +/* ETHER, GETHER MAC address */ +struct ether_mac_regs { + unsigned int reserved[114]; + unsigned int mahr; + unsigned int reserved2; + unsigned int malr; +}; +#define GETHER0_MAC_BASE ((struct ether_mac_regs *)0xfee0400) +#define GETHER1_MAC_BASE ((struct ether_mac_regs *)0xfee0c00) +#define ETHER0_MAC_BASE ((struct ether_mac_regs *)0xfef0000) +#define ETHER1_MAC_BASE ((struct ether_mac_regs *)0xfef0800) + +/* GETHER */ +struct gether_control_regs { + unsigned int gbecont; +}; +#define GETHER_CONTROL_BASE ((struct gether_control_regs *)0xffc10100) +#define GBECONT_RMII1 0x00020000 +#define GBECONT_RMII0 0x00010000 + +/* USB0/1 */ +struct usb_common_regs { + unsigned short reserved[129]; + unsigned short suspmode; +}; +#define USB0_COMMON_BASE ((struct usb_common_regs *)0xfe450000) +#define USB1_COMMON_BASE ((struct usb_common_regs *)0xfe4f0000) + +struct usb0_phy_regs { + unsigned short reset; + unsigned short reserved[4]; + unsigned short portsel; +}; +#define USB0_PHY_BASE ((struct usb0_phy_regs *)0xfe5f0000) + +struct usb1_port_regs { + unsigned int port1sel; + unsigned int reserved; + unsigned int usb1intsts; +}; +#define USB1_PORT_BASE ((struct usb1_port_regs *)0xfe4f2000) + +struct usb1_alignment_regs { + unsigned int ehcidatac; /* 0xfe4fe018 */ + unsigned int reserved[63]; + unsigned int ohcidatac; +}; +#define USB1_ALIGNMENT_BASE ((struct usb1_alignment_regs *)0xfe4fe018) + +/* GCTRL, GRA */ +struct gctrl_regs { + unsigned int wprotect; + unsigned int gplldiv; + unsigned int gracr2; /* GRA */ + unsigned int gracr3; /* GRA */ + unsigned int reserved[4]; + unsigned int fcntcr1; + unsigned int fcntcr2; + unsigned int reserved2[2]; + unsigned int gpll1div; + unsigned int vcompsel; + unsigned int reserved3[62]; + unsigned int fdlmon; + unsigned int reserved4[2]; + unsigned int flcrmon; + unsigned int reserved5[944]; + unsigned int spibootcan; +}; +#define GCTRL_BASE ((struct gctrl_regs *)0xffc10000) + +/* PCIe setup */ +struct pcie_setup_regs { + unsigned int pbictl0; + unsigned int gradevctl; + unsigned int reserved[2]; + unsigned int bmcinf[6]; + unsigned int reserved2[118]; + unsigned int idset[2]; + unsigned int subidset; + unsigned int reserved3[2]; + unsigned int linkconfset[4]; + unsigned int trsid; + unsigned int reserved4[6]; + unsigned int toutset; + unsigned int reserved5[7]; + unsigned int lad0; + unsigned int ladmsk0; + unsigned int lad1; + unsigned int ladmsk1; + unsigned int lad2; + unsigned int ladmsk2; + unsigned int lad3; + unsigned int ladmsk3; + unsigned int lad4; + unsigned int ladmsk4; + unsigned int lad5; + unsigned int ladmsk5; + unsigned int reserved6[94]; + unsigned int vdmrxvid[2]; + unsigned int reserved7; + unsigned int pbiintfr; + unsigned int pbiinten; + unsigned int msimap; + unsigned int barmap; + unsigned int baracsize; + unsigned int advserest; + unsigned int pbictl3; + unsigned int reserved8[8]; + unsigned int pbictl1; + unsigned int scratch0; + unsigned int reserved9[6]; + unsigned int pbictl2; + unsigned int reserved10; + unsigned int pbirev; +}; +#define PCIE_SETUP_BASE ((struct pcie_setup_regs *)0xffca1000) + +struct pcie_system_bus_regs { + unsigned int reserved[3]; + unsigned int endictl0; + unsigned int endictl1; +}; +#define PCIE_SYSTEM_BUS_BASE ((struct pcie_system_bus_regs *)0xffca1600) + + +/* PCIe-Bridge */ +struct pciebrg_regs { + unsigned short ctrl_h8s; + unsigned short reserved[7]; + unsigned short cp_addr; + unsigned short reserved2; + unsigned short cp_data; + unsigned short reserved3; + unsigned short cp_ctrl; +}; +#define PCIEBRG_BASE ((struct pciebrg_regs *)0xffd60000) + +/* CPU version */ +#define CCN_PRR 0xff000044 +#define prr_mask(_val) ((_val >> 4) & 0xff) +#define PRR_SH7757_B0 0x10 +#define PRR_SH7757_C0 0x11 + +#define is_sh7757_b0(_val) \ +({ \ + int __ret = prr_mask(__raw_readl(CCN_PRR)) == PRR_SH7757_B0; \ + __ret; \ +}) +#endif /* ifndef __ASSEMBLY__ */ + +#endif /* _ASM_CPU_SH7757_H_ */ diff --git a/board/espt/config.mk b/board/espt/config.mk deleted file mode 100644 index 21b51de..0000000 --- a/board/espt/config.mk +++ /dev/null @@ -1,9 +0,0 @@ -# -# board/espt/config.mk -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 diff --git a/board/mpr2/config.mk b/board/mpr2/config.mk deleted file mode 100644 index 4a4bca1..0000000 --- a/board/mpr2/config.mk +++ /dev/null @@ -1,37 +0,0 @@ -# -# Copyright (C) 2007 -# Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> -# -# Copyright (C) 2007 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# Copyright (C) 2007 -# Kenati Technologies, Inc. -# -# Copyright (C) 2008 -# Mark Jonas <mark.jonas@de.bosch.com> -# -# board/mpr2/config.mk -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 diff --git a/board/ms7720se/config.mk b/board/ms7720se/config.mk deleted file mode 100644 index d2944a6..0000000 --- a/board/ms7720se/config.mk +++ /dev/null @@ -1,34 +0,0 @@ -# -# Copyright (C) 2007 -# Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> -# -# Copyright (C) 2007 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# Copyright (C) 2007 -# Kenati Technologies, Inc. -# -# board/ms7720se/config.mk -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 diff --git a/board/ms7722se/config.mk b/board/ms7722se/config.mk deleted file mode 100644 index 3f1606b..0000000 --- a/board/ms7722se/config.mk +++ /dev/null @@ -1,31 +0,0 @@ -# -# Copyright (C) 2007 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# Copyright (C) 2007 -# Kenati Technologies, Inc. -# -# board/ms7722se/config.mk -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 diff --git a/board/ms7750se/config.mk b/board/ms7750se/config.mk deleted file mode 100644 index ba4d155..0000000 --- a/board/ms7750se/config.mk +++ /dev/null @@ -1,23 +0,0 @@ -# -# Copyright (C) 2007 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 diff --git a/board/renesas/ap325rxa/config.mk b/board/renesas/ap325rxa/config.mk deleted file mode 100644 index f572afd..0000000 --- a/board/renesas/ap325rxa/config.mk +++ /dev/null @@ -1,26 +0,0 @@ -# -# Copyright (C) 2007 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 diff --git a/board/renesas/r2dplus/config.mk b/board/renesas/r2dplus/config.mk deleted file mode 100644 index 55163b9..0000000 --- a/board/renesas/r2dplus/config.mk +++ /dev/null @@ -1,23 +0,0 @@ -# -# Copyright (C) 2007,2008 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# -CONFIG_SYS_TEXT_BASE = 0x0FFC0000 diff --git a/board/renesas/r7780mp/config.mk b/board/renesas/r7780mp/config.mk deleted file mode 100644 index 70ee3fd..0000000 --- a/board/renesas/r7780mp/config.mk +++ /dev/null @@ -1,27 +0,0 @@ -# -# Copyright (C) 2007,2008 Nobuhiro Iwamatsu -# -# board/r77870mp/config.mk -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x0FFC0000 diff --git a/board/renesas/rsk7203/config.mk b/board/renesas/rsk7203/config.mk deleted file mode 100644 index 5b533f6..0000000 --- a/board/renesas/rsk7203/config.mk +++ /dev/null @@ -1,28 +0,0 @@ -# -# Copyright (C) 2007,2008 Nobuhiro Iwamatsu -# Copyright (C) 2008 Renesas Solutions Corp. -# -# u-boot/board/rsk7203/config.mk -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x0C7C0000 diff --git a/board/renesas/MigoR/config.mk b/board/renesas/sh7757lcr/Makefile index ffe954c..e2e46ba 100644 --- a/board/renesas/MigoR/config.mk +++ b/board/renesas/sh7757lcr/Makefile @@ -1,11 +1,5 @@ # -# Copyright (C) 2007 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# Copyright (C) 2007 -# Kenati Technologies, Inc. -# -# board/MigoR/config.mk +# Copyright (C) 2011 Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # # This program is free software; you can redistribute it and/or # modify it under the terms of the GNU General Public License as @@ -22,10 +16,28 @@ # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := sh7757lcr.o spi-boot.o +SOBJS := lowlevel_init.o + +$(LIB): $(obj).depend $(COBJS) $(SOBJS) + $(call cmd_link_o_target, $(COBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 diff --git a/board/renesas/sh7757lcr/lowlevel_init.S b/board/renesas/sh7757lcr/lowlevel_init.S new file mode 100644 index 0000000..ab1aa49 --- /dev/null +++ b/board/renesas/sh7757lcr/lowlevel_init.S @@ -0,0 +1,558 @@ +/* + * Copyright (C) 2011 Renesas Solutions Corp. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <version.h> +#include <asm/processor.h> +#include <asm/macro.h> + +.macro or32, addr, data + mov.l \addr, r1 + mov.l \data, r0 + mov.l @r1, r2 + or r2, r0 + mov.l r0, @r1 +.endm + +.macro wait_DBCMD + mov.l DBWAIT_A, r0 + mov.l @r0, r1 +.endm + + .global lowlevel_init + .section .spiboot1.text + .align 2 + +lowlevel_init: + + /*------- GPIO -------*/ + write8 PGDR_A, PGDR_D /* eMMC power off */ + + write16 PACR_A, PACR_D + write16 PBCR_A, PBCR_D + write16 PCCR_A, PCCR_D + write16 PDCR_A, PDCR_D + write16 PECR_A, PECR_D + write16 PFCR_A, PFCR_D + write16 PGCR_A, PGCR_D + write16 PHCR_A, PHCR_D + write16 PICR_A, PICR_D + write16 PJCR_A, PJCR_D + write16 PKCR_A, PKCR_D + write16 PLCR_A, PLCR_D + write16 PMCR_A, PMCR_D + write16 PNCR_A, PNCR_D + write16 POCR_A, POCR_D + write16 PQCR_A, PQCR_D + write16 PRCR_A, PRCR_D + write16 PSCR_A, PSCR_D + write16 PTCR_A, PTCR_D + write16 PUCR_A, PUCR_D + write16 PVCR_A, PVCR_D + write16 PWCR_A, PWCR_D + write16 PXCR_A, PXCR_D + write16 PYCR_A, PYCR_D + write16 PZCR_A, PZCR_D + write16 PSEL0_A, PSEL0_D + write16 PSEL1_A, PSEL1_D + write16 PSEL2_A, PSEL2_D + write16 PSEL3_A, PSEL3_D + write16 PSEL4_A, PSEL4_D + write16 PSEL5_A, PSEL5_D + write16 PSEL6_A, PSEL6_D + write16 PSEL7_A, PSEL7_D + write16 PSEL8_A, PSEL8_D + + bra exit_gpio + nop + + .align 4 + +/*------- GPIO -------*/ +PGDR_A: .long 0xffec0040 +PACR_A: .long 0xffec0000 +PBCR_A: .long 0xffec0002 +PCCR_A: .long 0xffec0004 +PDCR_A: .long 0xffec0006 +PECR_A: .long 0xffec0008 +PFCR_A: .long 0xffec000a +PGCR_A: .long 0xffec000c +PHCR_A: .long 0xffec000e +PICR_A: .long 0xffec0010 +PJCR_A: .long 0xffec0012 +PKCR_A: .long 0xffec0014 +PLCR_A: .long 0xffec0016 +PMCR_A: .long 0xffec0018 +PNCR_A: .long 0xffec001a +POCR_A: .long 0xffec001c +PQCR_A: .long 0xffec0020 +PRCR_A: .long 0xffec0022 +PSCR_A: .long 0xffec0024 +PTCR_A: .long 0xffec0026 +PUCR_A: .long 0xffec0028 +PVCR_A: .long 0xffec002a +PWCR_A: .long 0xffec002c +PXCR_A: .long 0xffec002e +PYCR_A: .long 0xffec0030 +PZCR_A: .long 0xffec0032 +PSEL0_A: .long 0xffec0070 +PSEL1_A: .long 0xffec0072 +PSEL2_A: .long 0xffec0074 +PSEL3_A: .long 0xffec0076 +PSEL4_A: .long 0xffec0078 +PSEL5_A: .long 0xffec007a +PSEL6_A: .long 0xffec007c +PSEL7_A: .long 0xffec0082 +PSEL8_A: .long 0xffec0084 + +PGDR_D: .long 0x80 +PACR_D: .long 0x0000 +PBCR_D: .long 0x0001 +PCCR_D: .long 0x0000 +PDCR_D: .long 0x0000 +PECR_D: .long 0x0000 +PFCR_D: .long 0x0000 +PGCR_D: .long 0x0000 +PHCR_D: .long 0x0000 +PICR_D: .long 0x0000 +PJCR_D: .long 0x0000 +PKCR_D: .long 0x0003 +PLCR_D: .long 0x0000 +PMCR_D: .long 0x0000 +PNCR_D: .long 0x0000 +POCR_D: .long 0x0000 +PQCR_D: .long 0xc000 +PRCR_D: .long 0x0000 +PSCR_D: .long 0x0000 +PTCR_D: .long 0x0000 +#if defined(CONFIG_SH7757_OFFSET_SPI) +PUCR_D: .long 0x0055 +#else +PUCR_D: .long 0x0000 +#endif +PVCR_D: .long 0x0000 +PWCR_D: .long 0x0000 +PXCR_D: .long 0x0000 +PYCR_D: .long 0x0000 +PZCR_D: .long 0x0000 +PSEL0_D: .long 0xfe00 +PSEL1_D: .long 0x0000 +PSEL2_D: .long 0x3000 +PSEL3_D: .long 0xff00 +PSEL4_D: .long 0x771f +PSEL5_D: .long 0x0ffc +PSEL6_D: .long 0x00ff +PSEL7_D: .long 0xfc00 +PSEL8_D: .long 0x0000 + + .align 2 + +exit_gpio: + mov #0, r14 + mova 2f, r0 + mov.l PC_MASK, r1 + tst r0, r1 + bf 2f + + bra exit_pmb + nop + + .align 2 + +/* If CPU runs on SDRAM, PC is 0x8???????. */ +PC_MASK: .long 0x20000000 + +2: + mov #1, r14 + + mov.l EXPEVT_A, r0 + mov.l @r0, r0 + mov.l EXPEVT_POWER_ON_RESET, r1 + cmp/eq r0, r1 + bt 1f + + /* + * If EXPEVT value is manual reset or tlb multipul-hit, + * initialization of DDR3IF is not necessary. + */ + bra exit_ddr + nop + +1: + /* For Core Reset */ + mov.l DBACEN_A, r0 + mov.l @r0, r0 + cmp/eq #0, r0 + bt 3f + + /* + * If DBACEN == 1(DBSC was already enabled), we have to avoid the + * initialization of DDR3-SDRAM. + */ + bra exit_ddr + nop + +3: + /*------- DDR3IF -------*/ + /* oscillation stabilization time */ + wait_timer WAIT_OSC_TIME + + /* step 3 */ + write32 DBCMD_A, DBCMD_RSTL_VAL + wait_timer WAIT_30US + + /* step 4 */ + write32 DBCMD_A, DBCMD_PDEN_VAL + + /* step 5 */ + write32 DBKIND_A, DBKIND_D + + /* step 6 */ + write32 DBCONF_A, DBCONF_D + write32 DBTR0_A, DBTR0_D + write32 DBTR1_A, DBTR1_D + write32 DBTR2_A, DBTR2_D + write32 DBTR3_A, DBTR3_D + write32 DBTR4_A, DBTR4_D + write32 DBTR5_A, DBTR5_D + write32 DBTR6_A, DBTR6_D + write32 DBTR7_A, DBTR7_D + write32 DBTR8_A, DBTR8_D + write32 DBTR9_A, DBTR9_D + write32 DBTR10_A, DBTR10_D + write32 DBTR11_A, DBTR11_D + write32 DBTR12_A, DBTR12_D + write32 DBTR13_A, DBTR13_D + write32 DBTR14_A, DBTR14_D + write32 DBTR15_A, DBTR15_D + write32 DBTR16_A, DBTR16_D + write32 DBTR17_A, DBTR17_D + write32 DBTR18_A, DBTR18_D + write32 DBTR19_A, DBTR19_D + write32 DBRNK0_A, DBRNK0_D + + /* step 7 */ + write32 DBPDCNT3_A, DBPDCNT3_D + + /* step 8 */ + write32 DBPDCNT1_A, DBPDCNT1_D + write32 DBPDCNT2_A, DBPDCNT2_D + write32 DBPDLCK_A, DBPDLCK_D + write32 DBPDRGA_A, DBPDRGA_D + write32 DBPDRGD_A, DBPDRGD_D + + /* step 9 */ + wait_timer WAIT_30US + + /* step 10 */ + write32 DBPDCNT0_A, DBPDCNT0_D + + /* step 11 */ + wait_timer WAIT_30US + wait_timer WAIT_30US + + /* step 12 */ + write32 DBCMD_A, DBCMD_WAIT_VAL + wait_DBCMD + + /* step 13 */ + write32 DBCMD_A, DBCMD_RSTH_VAL + wait_DBCMD + + /* step 14 */ + write32 DBCMD_A, DBCMD_WAIT_VAL + write32 DBCMD_A, DBCMD_WAIT_VAL + write32 DBCMD_A, DBCMD_WAIT_VAL + write32 DBCMD_A, DBCMD_WAIT_VAL + + /* step 15 */ + write32 DBCMD_A, DBCMD_PDXT_VAL + + /* step 16 */ + write32 DBCMD_A, DBCMD_MRS2_VAL + + /* step 17 */ + write32 DBCMD_A, DBCMD_MRS3_VAL + + /* step 18 */ + write32 DBCMD_A, DBCMD_MRS1_VAL + + /* step 19 */ + write32 DBCMD_A, DBCMD_MRS0_VAL + + /* step 20 */ + write32 DBCMD_A, DBCMD_ZQCL_VAL + + write32 DBCMD_A, DBCMD_REF_VAL + write32 DBCMD_A, DBCMD_REF_VAL + wait_DBCMD + + /* step 21 */ + write32 DBADJ0_A, DBADJ0_D + write32 DBADJ1_A, DBADJ1_D + write32 DBADJ2_A, DBADJ2_D + + /* step 22 */ + write32 DBRFCNF0_A, DBRFCNF0_D + write32 DBRFCNF1_A, DBRFCNF1_D + write32 DBRFCNF2_A, DBRFCNF2_D + + /* step 23 */ + write32 DBCALCNF_A, DBCALCNF_D + + /* step 24 */ + write32 DBRFEN_A, DBRFEN_D + write32 DBCMD_A, DBCMD_SRXT_VAL + + /* step 25 */ + write32 DBACEN_A, DBACEN_D + + /* step 26 */ + wait_DBCMD + + /* enable DDR-ECC */ + write32 ECD_ECDEN_A, ECD_ECDEN_D + write32 ECD_INTSR_A, ECD_INTSR_D + write32 ECD_SPACER_A, ECD_SPACER_D + write32 ECD_MCR_A, ECD_MCR_D + + bra exit_ddr + nop + + .align 4 + +EXPEVT_A: .long 0xff000024 +EXPEVT_POWER_ON_RESET: .long 0x00000000 + +/*------- DDR3IF -------*/ +DBCMD_A: .long 0xfe800018 +DBKIND_A: .long 0xfe800020 +DBCONF_A: .long 0xfe800024 +DBTR0_A: .long 0xfe800040 +DBTR1_A: .long 0xfe800044 +DBTR2_A: .long 0xfe800048 +DBTR3_A: .long 0xfe800050 +DBTR4_A: .long 0xfe800054 +DBTR5_A: .long 0xfe800058 +DBTR6_A: .long 0xfe80005c +DBTR7_A: .long 0xfe800060 +DBTR8_A: .long 0xfe800064 +DBTR9_A: .long 0xfe800068 +DBTR10_A: .long 0xfe80006c +DBTR11_A: .long 0xfe800070 +DBTR12_A: .long 0xfe800074 +DBTR13_A: .long 0xfe800078 +DBTR14_A: .long 0xfe80007c +DBTR15_A: .long 0xfe800080 +DBTR16_A: .long 0xfe800084 +DBTR17_A: .long 0xfe800088 +DBTR18_A: .long 0xfe80008c +DBTR19_A: .long 0xfe800090 +DBRNK0_A: .long 0xfe800100 +DBPDCNT0_A: .long 0xfe800200 +DBPDCNT1_A: .long 0xfe800204 +DBPDCNT2_A: .long 0xfe800208 +DBPDCNT3_A: .long 0xfe80020c +DBPDLCK_A: .long 0xfe800280 +DBPDRGA_A: .long 0xfe800290 +DBPDRGD_A: .long 0xfe8002a0 +DBADJ0_A: .long 0xfe8000c0 +DBADJ1_A: .long 0xfe8000c4 +DBADJ2_A: .long 0xfe8000c8 +DBRFCNF0_A: .long 0xfe8000e0 +DBRFCNF1_A: .long 0xfe8000e4 +DBRFCNF2_A: .long 0xfe8000e8 +DBCALCNF_A: .long 0xfe8000f4 +DBRFEN_A: .long 0xfe800014 +DBACEN_A: .long 0xfe800010 +DBWAIT_A: .long 0xfe80001c + +WAIT_OSC_TIME: .long 6000 +WAIT_30US: .long 13333 + +DBCMD_RSTL_VAL: .long 0x20000000 +DBCMD_PDEN_VAL: .long 0x1000d73c +DBCMD_WAIT_VAL: .long 0x0000d73c +DBCMD_RSTH_VAL: .long 0x2100d73c +DBCMD_PDXT_VAL: .long 0x110000c8 +DBCMD_MRS0_VAL: .long 0x28000930 +DBCMD_MRS1_VAL: .long 0x29000004 +DBCMD_MRS2_VAL: .long 0x2a000008 +DBCMD_MRS3_VAL: .long 0x2b000000 +DBCMD_ZQCL_VAL: .long 0x03000200 +DBCMD_REF_VAL: .long 0x0c000000 +DBCMD_SRXT_VAL: .long 0x19000000 +DBKIND_D: .long 0x00000007 +DBCONF_D: .long 0x0f030a01 +DBTR0_D: .long 0x00000007 +DBTR1_D: .long 0x00000006 +DBTR2_D: .long 0x00000000 +DBTR3_D: .long 0x00000007 +DBTR4_D: .long 0x00070007 +DBTR5_D: .long 0x0000001b +DBTR6_D: .long 0x00000014 +DBTR7_D: .long 0x00000005 +DBTR8_D: .long 0x00000015 +DBTR9_D: .long 0x00000006 +DBTR10_D: .long 0x00000008 +DBTR11_D: .long 0x00000007 +DBTR12_D: .long 0x0000000e +DBTR13_D: .long 0x00000056 +DBTR14_D: .long 0x00000006 +DBTR15_D: .long 0x00000004 +DBTR16_D: .long 0x00150002 +DBTR17_D: .long 0x000c0017 +DBTR18_D: .long 0x00000200 +DBTR19_D: .long 0x00000040 +DBRNK0_D: .long 0x00000001 +DBPDCNT0_D: .long 0x00000001 +DBPDCNT1_D: .long 0x00000001 +DBPDCNT2_D: .long 0x00000000 +DBPDCNT3_D: .long 0x00004010 +DBPDLCK_D: .long 0x0000a55a +DBPDRGA_D: .long 0x00000028 +DBPDRGD_D: .long 0x00017100 + +DBADJ0_D: .long 0x00000000 +DBADJ1_D: .long 0x00000000 +DBADJ2_D: .long 0x18061806 +DBRFCNF0_D: .long 0x000001ff +DBRFCNF1_D: .long 0x08001000 +DBRFCNF2_D: .long 0x00000000 +DBCALCNF_D: .long 0x0000ffff +DBRFEN_D: .long 0x00000001 +DBACEN_D: .long 0x00000001 + +/*------- DDR-ECC -------*/ +ECD_ECDEN_A: .long 0xffc1012c +ECD_ECDEN_D: .long 0x00000001 +ECD_INTSR_A: .long 0xfe900024 +ECD_INTSR_D: .long 0xffffffff +ECD_SPACER_A: .long 0xfe900018 +ECD_SPACER_D: .long SH7757LCR_SDRAM_ECC_SETTING +ECD_MCR_A: .long 0xfe900010 +ECD_MCR_D: .long 0x00000001 + + .align 2 +exit_ddr: + +#if defined(CONFIG_SH_32BIT) + /*------- set PMB -------*/ + write32 PASCR_A, PASCR_29BIT_D + write32 MMUCR_A, MMUCR_D + + /***************************************************************** + * ent virt phys v sz c wt + * 0 0xa0000000 0x00000000 1 128M 0 1 + * 1 0xa8000000 0x48000000 1 128M 0 1 + * 5 0x88000000 0x48000000 1 128M 1 1 + */ + write32 PMB_ADDR_SPIBOOT_A, PMB_ADDR_SPIBOOT_D + write32 PMB_DATA_SPIBOOT_A, PMB_DATA_SPIBOOT_D + write32 PMB_ADDR_DDR_C1_A, PMB_ADDR_DDR_C1_D + write32 PMB_DATA_DDR_C1_A, PMB_DATA_DDR_C1_D + write32 PMB_ADDR_DDR_N1_A, PMB_ADDR_DDR_N1_D + write32 PMB_DATA_DDR_N1_A, PMB_DATA_DDR_N1_D + + write32 PMB_ADDR_ENTRY2, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY3, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY4, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY6, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY7, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY8, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY9, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY10, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY11, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY12, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY13, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY14, PMB_ADDR_NOT_USE_D + write32 PMB_ADDR_ENTRY15, PMB_ADDR_NOT_USE_D + + write32 PASCR_A, PASCR_INIT + mov.l DUMMY_ADDR, r0 + icbi @r0 +#endif /* if defined(CONFIG_SH_32BIT) */ + +exit_pmb: + /* CPU is running on ILRAM? */ + mov r14, r0 + tst #1, r0 + bt 1f + + mov.l _bss_start, r15 + mov.l _spiboot_main, r0 +100: bsrf r0 + nop + + .align 2 +_spiboot_main: .long (spiboot_main - (100b + 4)) +_bss_start: .long bss_start + +1: + + write32 CCR_A, CCR_D + + rts + nop + + .align 4 + +#if defined(CONFIG_SH_32BIT) +/*------- set PMB -------*/ +PMB_ADDR_SPIBOOT_A: .long PMB_ADDR_BASE(0) +PMB_ADDR_DDR_N1_A: .long PMB_ADDR_BASE(1) +PMB_ADDR_DDR_C1_A: .long PMB_ADDR_BASE(5) +PMB_ADDR_ENTRY2: .long PMB_ADDR_BASE(2) +PMB_ADDR_ENTRY3: .long PMB_ADDR_BASE(3) +PMB_ADDR_ENTRY4: .long PMB_ADDR_BASE(4) +PMB_ADDR_ENTRY6: .long PMB_ADDR_BASE(6) +PMB_ADDR_ENTRY7: .long PMB_ADDR_BASE(7) +PMB_ADDR_ENTRY8: .long PMB_ADDR_BASE(8) +PMB_ADDR_ENTRY9: .long PMB_ADDR_BASE(9) +PMB_ADDR_ENTRY10: .long PMB_ADDR_BASE(10) +PMB_ADDR_ENTRY11: .long PMB_ADDR_BASE(11) +PMB_ADDR_ENTRY12: .long PMB_ADDR_BASE(12) +PMB_ADDR_ENTRY13: .long PMB_ADDR_BASE(13) +PMB_ADDR_ENTRY14: .long PMB_ADDR_BASE(14) +PMB_ADDR_ENTRY15: .long PMB_ADDR_BASE(15) + +PMB_ADDR_SPIBOOT_D: .long mk_pmb_addr_val(0xa0) +PMB_ADDR_DDR_C1_D: .long mk_pmb_addr_val(0x88) +PMB_ADDR_DDR_N1_D: .long mk_pmb_addr_val(0xa8) +PMB_ADDR_NOT_USE_D: .long 0x00000000 + +PMB_DATA_SPIBOOT_A: .long PMB_DATA_BASE(0) +PMB_DATA_DDR_N1_A: .long PMB_DATA_BASE(1) +PMB_DATA_DDR_C1_A: .long PMB_DATA_BASE(5) + +/* ppn ub v s1 s0 c wt */ +PMB_DATA_SPIBOOT_D: .long mk_pmb_data_val(0x00, 0, 1, 1, 0, 0, 1) +PMB_DATA_DDR_C1_D: .long mk_pmb_data_val(0x48, 0, 1, 1, 0, 1, 1) +PMB_DATA_DDR_N1_D: .long mk_pmb_data_val(0x48, 1, 1, 1, 0, 0, 1) + +PASCR_A: .long 0xff000070 +DUMMY_ADDR: .long 0xa0000000 +PASCR_29BIT_D: .long 0x00000000 +PASCR_INIT: .long 0x80000080 +MMUCR_A: .long 0xff000010 +MMUCR_D: .long 0x00000004 /* clear ITLB */ +#endif /* CONFIG_SH_32BIT */ + +CCR_A: .long CCR +CCR_D: .long CCR_CACHE_INIT diff --git a/board/renesas/sh7757lcr/sh7757lcr.c b/board/renesas/sh7757lcr/sh7757lcr.c new file mode 100644 index 0000000..a62be24 --- /dev/null +++ b/board/renesas/sh7757lcr/sh7757lcr.c @@ -0,0 +1,454 @@ +/* + * Copyright (C) 2011 Renesas Solutions Corp. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <malloc.h> +#include <asm/processor.h> +#include <asm/io.h> +#include <spi_flash.h> + +int checkboard(void) +{ + puts("BOARD: R0P7757LC0030RL board\n"); + + return 0; +} + +static void init_gctrl(void) +{ + struct gctrl_regs *gctrl = GCTRL_BASE; + unsigned long graofst; + + graofst = (SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET) >> 24; + writel(graofst | 0x20000f00, &gctrl->gracr3); +} + +static int init_pcie_bridge_from_spi(void *buf, size_t size) +{ + struct spi_flash *spi; + int ret; + unsigned long pcie_addr; + + spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3); + if (!spi) { + printf("%s: spi_flash probe error.\n", __func__); + return 1; + } + + if (is_sh7757_b0()) + pcie_addr = SH7757LCR_PCIEBRG_ADDR_B0; + else + pcie_addr = SH7757LCR_PCIEBRG_ADDR; + + ret = spi_flash_read(spi, pcie_addr, size, buf); + if (ret) { + printf("%s: spi_flash read error.\n", __func__); + spi_flash_free(spi); + return 1; + } + spi_flash_free(spi); + + return 0; +} + +static void init_pcie_bridge(void) +{ + struct pciebrg_regs *pciebrg = PCIEBRG_BASE; + struct pcie_setup_regs *pcie_setup = PCIE_SETUP_BASE; + int i; + unsigned char *data; + unsigned short tmp; + unsigned long pcie_size; + + if (!(readw(&pciebrg->ctrl_h8s) & 0x0001)) + return; + + if (is_sh7757_b0()) + pcie_size = SH7757LCR_PCIEBRG_SIZE_B0; + else + pcie_size = SH7757LCR_PCIEBRG_SIZE; + + data = malloc(pcie_size); + if (!data) { + printf("%s: malloc error.\n", __func__); + return; + } + if (init_pcie_bridge_from_spi(data, pcie_size)) { + free(data); + return; + } + + if (data[0] == 0xff && data[1] == 0xff && data[2] == 0xff && + data[3] == 0xff) { + free(data); + printf("%s: skipped initialization\n", __func__); + return; + } + + writew(0xa501, &pciebrg->ctrl_h8s); /* reset */ + writew(0x0000, &pciebrg->cp_ctrl); + writew(0x0000, &pciebrg->cp_addr); + + for (i = 0; i < pcie_size; i += 2) { + tmp = (data[i] << 8) | data[i + 1]; + writew(tmp, &pciebrg->cp_data); + } + + writew(0xa500, &pciebrg->ctrl_h8s); /* start */ + if (!is_sh7757_b0()) + writel(0x00000001, &pcie_setup->pbictl3); + + free(data); +} + +static void init_usb_phy(void) +{ + struct usb_common_regs *common0 = USB0_COMMON_BASE; + struct usb_common_regs *common1 = USB1_COMMON_BASE; + struct usb0_phy_regs *phy = USB0_PHY_BASE; + struct usb1_port_regs *port = USB1_PORT_BASE; + struct usb1_alignment_regs *align = USB1_ALIGNMENT_BASE; + + writew(0x0100, &phy->reset); /* set reset */ + /* port0 = USB0, port1 = USB1 */ + writew(0x0002, &phy->portsel); + writel(0x0001, &port->port1sel); /* port1 = Host */ + writew(0x0111, &phy->reset); /* clear reset */ + + writew(0x4000, &common0->suspmode); + writew(0x4000, &common1->suspmode); + +#if defined(__LITTLE_ENDIAN) + writel(0x00000000, &align->ehcidatac); + writel(0x00000000, &align->ohcidatac); +#endif +} + +static void set_mac_to_sh_eth_register(int channel, char *mac_string) +{ + struct ether_mac_regs *ether; + unsigned char mac[6]; + unsigned long val; + + eth_parse_enetaddr(mac_string, mac); + + if (!channel) + ether = ETHER0_MAC_BASE; + else + ether = ETHER1_MAC_BASE; + + val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3]; + writel(val, ðer->mahr); + val = (mac[4] << 8) | mac[5]; + writel(val, ðer->malr); +} + +static void set_mac_to_sh_giga_eth_register(int channel, char *mac_string) +{ + struct ether_mac_regs *ether; + unsigned char mac[6]; + unsigned long val; + + eth_parse_enetaddr(mac_string, mac); + + if (!channel) + ether = GETHER0_MAC_BASE; + else + ether = GETHER1_MAC_BASE; + + val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3]; + writel(val, ðer->mahr); + val = (mac[4] << 8) | mac[5]; + writel(val, ðer->malr); +} + +/***************************************************************** + * This PMB must be set on this timing. The lowlevel_init is run on + * Area 0(phys 0x00000000), so we have to map it. + * + * The new PMB table is following: + * ent virt phys v sz c wt + * 0 0xa0000000 0x40000000 1 128M 0 1 + * 1 0xa8000000 0x48000000 1 128M 0 1 + * 2 0xb0000000 0x50000000 1 128M 0 1 + * 3 0xb8000000 0x58000000 1 128M 0 1 + * 4 0x80000000 0x40000000 1 128M 1 1 + * 5 0x88000000 0x48000000 1 128M 1 1 + * 6 0x90000000 0x50000000 1 128M 1 1 + * 7 0x98000000 0x58000000 1 128M 1 1 + */ +static void set_pmb_on_board_init(void) +{ + struct mmu_regs *mmu = MMU_BASE; + + /* clear ITLB */ + writel(0x00000004, &mmu->mmucr); + + /* delete PMB for SPIBOOT */ + writel(0, PMB_ADDR_BASE(0)); + writel(0, PMB_DATA_BASE(0)); + + /* add PMB for SDRAM(0x40000000 - 0x47ffffff) */ + /* ppn ub v s1 s0 c wt */ + writel(mk_pmb_addr_val(0xa0), PMB_ADDR_BASE(0)); + writel(mk_pmb_data_val(0x40, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(0)); + writel(mk_pmb_addr_val(0xb0), PMB_ADDR_BASE(2)); + writel(mk_pmb_data_val(0x50, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(2)); + writel(mk_pmb_addr_val(0xb8), PMB_ADDR_BASE(3)); + writel(mk_pmb_data_val(0x58, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(3)); + writel(mk_pmb_addr_val(0x80), PMB_ADDR_BASE(4)); + writel(mk_pmb_data_val(0x40, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(4)); + writel(mk_pmb_addr_val(0x90), PMB_ADDR_BASE(6)); + writel(mk_pmb_data_val(0x50, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(6)); + writel(mk_pmb_addr_val(0x98), PMB_ADDR_BASE(7)); + writel(mk_pmb_data_val(0x58, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(7)); +} + +int board_init(void) +{ + struct gether_control_regs *gether = GETHER_CONTROL_BASE; + + set_pmb_on_board_init(); + + /* enable RMII's MDIO (disable GRMII's MDIO) */ + writel(0x00030000, &gether->gbecont); + + init_gctrl(); + init_usb_phy(); + + return 0; +} + +int dram_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE; + gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE; + printf("DRAM: %dMB\n", CONFIG_SYS_SDRAM_SIZE / (1024 * 1024)); + printf(" Physical address\n"); + printf(" 0x%08x - 0x%08x : Accessible Space as ECC Area\n", + SH7757LCR_SDRAM_PHYS_TOP, + SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_SIZE - 1); + printf(" 0x%08x - 0x%08x : No Access Area\n", + SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_SIZE, + SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_SIZE * 2 - 1); + printf(" 0x%08x - 0x%08x : Non-ECC Area for DVC/AVC\n", + SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_ECC_SETTING * 2, + SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_ECC_SETTING * 2 + + SH7757LCR_SDRAM_DVC_SIZE - 1); + printf(" 0x%08x - 0x%08x : Non-ECC Area for G200eR2\n", + SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET, + SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET + 0x00ffffff); + + return 0; +} + +static int get_sh_eth_mac_raw(unsigned char *buf, int size) +{ + struct spi_flash *spi; + int ret; + + spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3); + if (spi == NULL) { + printf("%s: spi_flash probe error.\n", __func__); + return 1; + } + + ret = spi_flash_read(spi, SH7757LCR_ETHERNET_MAC_BASE, size, buf); + if (ret) { + printf("%s: spi_flash read error.\n", __func__); + spi_flash_free(spi); + return 1; + } + spi_flash_free(spi); + + return 0; +} + +static int get_sh_eth_mac(int channel, char *mac_string, unsigned char *buf) +{ + memcpy(mac_string, &buf[channel * (SH7757LCR_ETHERNET_MAC_SIZE + 1)], + SH7757LCR_ETHERNET_MAC_SIZE); + mac_string[SH7757LCR_ETHERNET_MAC_SIZE] = 0x00; /* terminate */ + + return 0; +} + +static void init_ethernet_mac(void) +{ + char mac_string[64]; + char env_string[64]; + int i; + unsigned char *buf; + + buf = malloc(256); + if (!buf) { + printf("%s: malloc error.\n", __func__); + return; + } + get_sh_eth_mac_raw(buf, 256); + + /* Fast Ethernet */ + for (i = 0; i < SH7757LCR_ETHERNET_NUM_CH; i++) { + get_sh_eth_mac(i, mac_string, buf); + if (i == 0) + setenv("ethaddr", mac_string); + else { + sprintf(env_string, "eth%daddr", i); + setenv(env_string, mac_string); + } + + set_mac_to_sh_eth_register(i, mac_string); + } + + /* Gigabit Ethernet */ + for (i = 0; i < SH7757LCR_GIGA_ETHERNET_NUM_CH; i++) { + get_sh_eth_mac(i + SH7757LCR_ETHERNET_NUM_CH, mac_string, buf); + sprintf(env_string, "eth%daddr", i + SH7757LCR_ETHERNET_NUM_CH); + setenv(env_string, mac_string); + + set_mac_to_sh_giga_eth_register(i, mac_string); + } + + free(buf); +} + +static void init_pcie(void) +{ + struct pcie_setup_regs *pcie_setup = PCIE_SETUP_BASE; + struct pcie_system_bus_regs *pcie_sysbus = PCIE_SYSTEM_BUS_BASE; + + writel(0x00000ff2, &pcie_setup->ladmsk0); + writel(0x00000001, &pcie_setup->barmap); + writel(0xffcaa000, &pcie_setup->lad0); + writel(0x00030000, &pcie_sysbus->endictl0); + writel(0x00000003, &pcie_sysbus->endictl1); + writel(0x00000004, &pcie_setup->pbictl2); +} + +static void finish_spiboot(void) +{ + struct gctrl_regs *gctrl = GCTRL_BASE; + /* + * SH7757 B0 does not use LBSC. + * So if we set SPIBOOTCAN to 1, SH7757 can not access Area0. + * This setting is not cleared by manual reset, So we have to set it + * to 0. + */ + writel(0x00000000, &gctrl->spibootcan); +} + +int board_late_init(void) +{ + init_ethernet_mac(); + init_pcie_bridge(); + init_pcie(); + finish_spiboot(); + + return 0; +} + +int do_sh_g200(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + struct gctrl_regs *gctrl = GCTRL_BASE; + unsigned long graofst; + + writel(0xfedcba98, &gctrl->wprotect); + graofst = (SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET) >> 24; + writel(graofst | 0xa0000f00, &gctrl->gracr3); + + return 0; +} + +U_BOOT_CMD( + sh_g200, 1, 1, do_sh_g200, + "enable sh-g200", + "enable SH-G200 bus (disable PCIe-G200)" +); + +int do_write_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int i, ret; + char mac_string[256]; + struct spi_flash *spi; + unsigned char *buf; + + if (argc != 5) { + buf = malloc(256); + if (!buf) { + printf("%s: malloc error.\n", __func__); + return 1; + } + + get_sh_eth_mac_raw(buf, 256); + + /* print current MAC address */ + for (i = 0; i < 4; i++) { + get_sh_eth_mac(i, mac_string, buf); + if (i < 2) + printf(" ETHERC ch%d = %s\n", i, mac_string); + else + printf("GETHERC ch%d = %s\n", i-2, mac_string); + } + free(buf); + return 0; + } + + /* new setting */ + memset(mac_string, 0xff, sizeof(mac_string)); + sprintf(mac_string, "%s\t%s\t%s\t%s", + argv[1], argv[2], argv[3], argv[4]); + + /* write MAC data to SPI rom */ + spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3); + if (!spi) { + printf("%s: spi_flash probe error.\n", __func__); + return 1; + } + + ret = spi_flash_erase(spi, SH7757LCR_ETHERNET_MAC_BASE_SPI, + SH7757LCR_SPI_SECTOR_SIZE); + if (ret) { + printf("%s: spi_flash erase error.\n", __func__); + return 1; + } + + ret = spi_flash_write(spi, SH7757LCR_ETHERNET_MAC_BASE_SPI, + sizeof(mac_string), mac_string); + if (ret) { + printf("%s: spi_flash write error.\n", __func__); + spi_flash_free(spi); + return 1; + } + spi_flash_free(spi); + + puts("The writing of the MAC address to SPI ROM was completed.\n"); + + return 0; +} + +U_BOOT_CMD( + write_mac, 5, 1, do_write_mac, + "write MAC address for ETHERC/GETHERC", + "[ETHERC ch0] [ETHERC ch1] [GETHERC ch0] [GETHERC ch1]\n" +); diff --git a/board/renesas/sh7757lcr/spi-boot.c b/board/renesas/sh7757lcr/spi-boot.c new file mode 100644 index 0000000..823844e --- /dev/null +++ b/board/renesas/sh7757lcr/spi-boot.c @@ -0,0 +1,109 @@ +/* + * Copyright (C) 2011 Renesas Solutions Corp. + * + * This file is subject to the terms and conditions of the GNU Lesser + * General Public License. See the file "COPYING.LIB" in the main + * directory of this archive for more details. + */ + +#include <common.h> + +#define CONFIG_RAM_BOOT_PHYS 0x4ef80000 +#if defined(CONFIG_SH7757_OFFSET_SPI) +#define CONFIG_SPI_ADDR 0x00010000 +#else +#define CONFIG_SPI_ADDR 0x00000000 +#endif +#define CONFIG_SPI_LENGTH 0x00030000 +#define CONFIG_RAM_BOOT 0x8ef80000 + +#define SPIWDMADR 0xFE001018 +#define SPIWDMCNTR 0xFE001020 +#define SPIDMCOR 0xFE001028 +#define SPIDMINTSR 0xFE001188 +#define SPIDMINTMR 0xFE001190 + +#define SPIDMINTSR_DMEND 0x00000004 + +#define TBR 0xFE002000 +#define RBR 0xFE002000 + +#define CR1 0xFE002008 +#define CR2 0xFE002010 +#define CR3 0xFE002018 +#define CR4 0xFE002020 + +/* CR1 */ +#define SPI_TBE 0x80 +#define SPI_TBF 0x40 +#define SPI_RBE 0x20 +#define SPI_RBF 0x10 +#define SPI_PFONRD 0x08 +#define SPI_SSDB 0x04 +#define SPI_SSD 0x02 +#define SPI_SSA 0x01 + +/* CR2 */ +#define SPI_RSTF 0x80 +#define SPI_LOOPBK 0x40 +#define SPI_CPOL 0x20 +#define SPI_CPHA 0x10 +#define SPI_L1M0 0x08 + +/* CR4 */ +#define SPI_TBEI 0x80 +#define SPI_TBFI 0x40 +#define SPI_RBEI 0x20 +#define SPI_RBFI 0x10 +#define SPI_SSS 0x01 + +#define spi_write(val, addr) (*(volatile unsigned long *)(addr)) = val +#define spi_read(addr) (*(volatile unsigned long *)(addr)) + +/* M25P80 */ +#define M25_READ 0x03 + +#define __uses_spiboot2 __attribute__((section(".spiboot2.text"))) +static void __uses_spiboot2 spi_reset(void) +{ + spi_write(0xfe, CR1); + + spi_write(0, SPIDMCOR); + spi_write(0x00, CR1); + + spi_write(spi_read(CR2) | SPI_RSTF, CR2); /* fifo reset */ + spi_write(spi_read(CR2) & ~SPI_RSTF, CR2); +} + +static void __uses_spiboot2 spi_read_flash(void *buf, unsigned long addr, + unsigned long len) +{ + spi_write(M25_READ, TBR); + spi_write((addr >> 16) & 0xFF, TBR); + spi_write((addr >> 8) & 0xFF, TBR); + spi_write(addr & 0xFF, TBR); + + spi_write(SPIDMINTSR_DMEND, SPIDMINTSR); + spi_write((unsigned long)buf, SPIWDMADR); + spi_write(len & 0xFFFFFFE0, SPIWDMCNTR); + spi_write(1, SPIDMCOR); + + spi_write(0xff, CR3); + spi_write(spi_read(CR1) | SPI_SSDB, CR1); + spi_write(spi_read(CR1) | SPI_SSA, CR1); + + while (!(spi_read(SPIDMINTSR) & SPIDMINTSR_DMEND)) + ; +} + +void __uses_spiboot2 spiboot_main(void) +{ + void (*_start)(void) = (void *)CONFIG_SYS_TEXT_BASE; + + spi_reset(); + spi_read_flash((void *)CONFIG_RAM_BOOT_PHYS, CONFIG_SPI_ADDR, + CONFIG_SPI_LENGTH); + + _start(); +} + diff --git a/board/renesas/sh7757lcr/u-boot.lds b/board/renesas/sh7757lcr/u-boot.lds new file mode 100644 index 0000000..a88d781 --- /dev/null +++ b/board/renesas/sh7757lcr/u-boot.lds @@ -0,0 +1,101 @@ +/* + * Copyright (C) 2007 + * Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + * + * Copyright (C) 2011 + * Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-sh-linux", "elf32-sh-linux", "elf32-sh-linux") +OUTPUT_ARCH(sh) +ENTRY(_start) + +SECTIONS +{ + /* + * entry and reloct_dst will be provided via ldflags + */ + . = .; + + PROVIDE (_ftext = .); + PROVIDE (_fcode = .); + PROVIDE (_start = .); + + .text : + { + arch/sh/cpu/sh4/start.o (.text) + *(.spiboot1.text) + *(.spiboot2.text) + . = ALIGN(8192); + common/env_embedded.o (.ppcenv) + . = ALIGN(8192); + common/env_embedded.o (.ppcenvr) + . = ALIGN(8192); + *(.text) + . = ALIGN(4); + } =0xFF + PROVIDE (_ecode = .); + .rodata : + { + *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) + . = ALIGN(4); + } + PROVIDE (_etext = .); + + + PROVIDE (_fdata = .); + .data : + { + *(.data) + . = ALIGN(4); + } + PROVIDE (_edata = .); + + PROVIDE (_fgot = .); + .got : + { + *(.got) + . = ALIGN(4); + } + PROVIDE (_egot = .); + + PROVIDE (__u_boot_cmd_start = .); + .u_boot_cmd : + { + *(.u_boot_cmd) + . = ALIGN(4); + } + PROVIDE (__u_boot_cmd_end = .); + + PROVIDE (reloc_dst_end = .); + /* _reloc_dst_end = .; */ + + PROVIDE (bss_start = .); + PROVIDE (__bss_start = .); + .bss (NOLOAD) : + { + *(.bss) + . = ALIGN(4); + } + PROVIDE (bss_end = .); + + PROVIDE (_end = .); +} diff --git a/board/renesas/sh7763rdp/config.mk b/board/renesas/sh7763rdp/config.mk deleted file mode 100644 index 54c1a5b..0000000 --- a/board/renesas/sh7763rdp/config.mk +++ /dev/null @@ -1,11 +0,0 @@ -# -# board/sh7763rdp/config.mk -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x8FFC0000 - -# PLATFORM_CPPFLAGS += -DCONFIG_MULTIBOOT diff --git a/board/renesas/sh7785lcr/Makefile b/board/renesas/sh7785lcr/Makefile index b5c496f..e404fa6 100644 --- a/board/renesas/sh7785lcr/Makefile +++ b/board/renesas/sh7785lcr/Makefile @@ -23,8 +23,12 @@ LIB = $(obj)lib$(BOARD).o COBJS := sh7785lcr.o selfcheck.o rtl8169_mac.o SOBJS := lowlevel_init.o -$(LIB): $(obj).depend $(COBJS) $(SOBJS) - $(call cmd_link_o_target, $(COBJS) $(SOBJS)) +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) clean: rm -f $(SOBJS) $(OBJS) diff --git a/board/renesas/sh7785lcr/config.mk b/board/renesas/sh7785lcr/config.mk deleted file mode 100644 index 6853d2b..0000000 --- a/board/renesas/sh7785lcr/config.mk +++ /dev/null @@ -1,31 +0,0 @@ -# -# Copyright (C) 2007 -# Nobuhiro Iwamatsu <iwamatsu@nigauri.org> -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -ifdef CONFIG_SH_32BIT -CONFIG_SYS_TEXT_BASE = 0x8FF80000 -else -CONFIG_SYS_TEXT_BASE = 0x0ff80000 -endif diff --git a/board/shmin/config.mk b/board/shmin/config.mk deleted file mode 100644 index 0c7605e..0000000 --- a/board/shmin/config.mk +++ /dev/null @@ -1,27 +0,0 @@ -# -# Copyright (C) 2010 Nobuhiro Iwamatsu -# -# u-boot/board/shmin/config.mk -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA - -# -# TEXT_BASE refers to image _after_ relocation. -# -# NOTE: Must match value used in u-boot.lds (in this directory). -# - -CONFIG_SYS_TEXT_BASE = 0x8DFB0000 @@ -751,6 +751,7 @@ ms7750se sh sh4 ms7750se - ap325rxa sh sh4 ap325rxa renesas - r2dplus sh sh4 r2dplus renesas - r7780mp sh sh4 r7780mp renesas - +sh7757lcr sh sh4 sh7757lcr renesas - sh7763rdp sh sh4 sh7763rdp renesas - sh7785lcr sh sh4 sh7785lcr renesas - sh7785lcr_32bit sh sh4 sh7785lcr renesas - sh7785lcr:SH_32BIT=1 diff --git a/common/env_nand.c b/common/env_nand.c index 2682f07..a4480cb 100644 --- a/common/env_nand.c +++ b/common/env_nand.c @@ -205,7 +205,7 @@ int saveenv(void) return 1; } env_new.crc = crc32(0, env_new.data, ENV_SIZE); - env_new.flags = ACTIVE_FLAG; + ++env_new.flags; /* increase the serial */ if(gd->env_valid == 1) { puts("Erasing redundant NAND...\n"); diff --git a/common/usb.c b/common/usb.c index 10e23de..44a435a 100644 --- a/common/usb.c +++ b/common/usb.c @@ -55,7 +55,10 @@ #include <asm/4xx_pci.h> #endif -#undef USB_DEBUG +#ifdef DEBUG +#define USB_DEBUG +#define USB_HUB_DEBUG +#endif #ifdef USB_DEBUG #define USB_PRINTF(fmt, args...) printf(fmt , ##args) @@ -960,8 +963,6 @@ void usb_scan_devices(void) * Probes device for being a hub and configurate it */ -#undef USB_HUB_DEBUG - #ifdef USB_HUB_DEBUG #define USB_HUB_PRINTF(fmt, args...) printf(fmt , ##args) #else @@ -1220,7 +1221,7 @@ int usb_hub_configure(struct usb_device *dev) hub->desc.DeviceRemovable[i] = descriptor->DeviceRemovable[i]; for (i = 0; i < ((hub->desc.bNbrPorts + 1 + 7)/8); i++) - hub->desc.DeviceRemovable[i] = descriptor->PortPowerCtrlMask[i]; + hub->desc.PortPowerCtrlMask[i] = descriptor->PortPowerCtrlMask[i]; dev->maxchild = descriptor->bNbrPorts; USB_HUB_PRINTF("%d ports detected\n", dev->maxchild); diff --git a/doc/README.sh7757lcr b/doc/README.sh7757lcr new file mode 100644 index 0000000..cae14e0 --- /dev/null +++ b/doc/README.sh7757lcr @@ -0,0 +1,64 @@ +======================================== +Renesas R0P7757LC0030RL board +======================================== + +This board specification: +========================= + +The R0P7757LC0030RL(board config name:sh7757lcr) has the following device: + + - SH7757 (SH-4A) + - DDR3-SDRAM 256MB (with ECC) + - SPI ROM 8MB + - 2D Graphic controller + - Ethernet controller + + +configuration for This board: +============================= + +You can select the configuration as follows: + + - make sh7785lcr_config + + +This board specific command: +============================ + +This board has the following its specific command: + + - sh_g200 + - write_mac + + +1. sh_g200 + +If we run this command, SH4 can control the G200. +The default setting is that SH4 cannot control the G200. + + +2. write_mac + +You can write MAC address to SPI ROM. + + Usage 1) Write MAC address + + write_mac [ETHERC ch0] [ETHERC ch1] [GETHERC ch0] [GETHERC ch1] + + For example) + => write_mac 00:00:87:6c:21:80 00:00:87:6c:21:81 00:00:87:6c:21:82 00:00:87:6c:21:83 + *) We have to input the command as a single line + (without carriage return) + *) We have to reset after input the command. + + Usage 2) Show current data + + write_mac + + For example) + => write_mac + ETHERC ch0 = 00:00:87:6c:21:80 + ETHERC ch1 = 00:00:87:6c:21:81 + GETHERC ch0 = 00:00:87:6c:21:82 + GETHERC ch1 = 00:00:87:6c:21:83 + diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index d01c926..f3cccbe 100644 --- a/drivers/mmc/fsl_esdhc.c +++ b/drivers/mmc/fsl_esdhc.c @@ -219,6 +219,11 @@ static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data) if (timeout < 0) timeout = 0; +#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 + if ((timeout == 4) || (timeout == 8) || (timeout == 12)) + timeout++; +#endif + esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, timeout << 16); return 0; diff --git a/drivers/net/sh_eth.c b/drivers/net/sh_eth.c index 86cc324..53d918d 100644 --- a/drivers/net/sh_eth.c +++ b/drivers/net/sh_eth.c @@ -36,6 +36,12 @@ #ifndef CONFIG_SH_ETHER_PHY_ADDR # error "Please define CONFIG_SH_ETHER_PHY_ADDR" #endif +#ifdef CONFIG_SH_ETHER_CACHE_WRITEBACK +#define flush_cache_wback(addr, len) \ + dcache_wback_range((u32)addr, (u32)(addr + len - 1)) +#else +#define flush_cache_wback(...) +#endif #define SH_ETH_PHY_DELAY 50000 @@ -197,6 +203,7 @@ int sh_eth_send(struct eth_device *dev, volatile void *packet, int len) } /* Update tx descriptor */ + flush_cache_wback(packet, len); port_info->tx_desc_cur->td2 = ADDR_TO_PHY(packet); port_info->tx_desc_cur->td1 = len << 16; /* Must preserve the end of descriptor list indication */ @@ -312,6 +319,7 @@ static int sh_eth_tx_desc_init(struct sh_eth_dev *eth) tmp_addr = (u32) (((int)port_info->tx_desc_malloc + TX_DESC_SIZE - 1) & ~(TX_DESC_SIZE - 1)); + flush_cache_wback(tmp_addr, NUM_TX_DESC * sizeof(struct tx_desc_s)); /* Make sure we use a P2 address (non-cacheable) */ port_info->tx_desc_base = (struct tx_desc_s *)ADDR_TO_P2(tmp_addr); port_info->tx_desc_cur = port_info->tx_desc_base; @@ -361,6 +369,7 @@ static int sh_eth_rx_desc_init(struct sh_eth_dev *eth) tmp_addr = (u32) (((int)port_info->rx_desc_malloc + RX_DESC_SIZE - 1) & ~(RX_DESC_SIZE - 1)); + flush_cache_wback(tmp_addr, NUM_RX_DESC * sizeof(struct rx_desc_s)); /* Make sure we use a P2 address (non-cacheable) */ port_info->rx_desc_base = (struct rx_desc_s *)ADDR_TO_P2(tmp_addr); diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index e34a124..d582fbb 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -37,6 +37,7 @@ COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o COBJS-$(CONFIG_OMAP3_SPI) += omap3_spi.o COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o +COBJS-$(CONFIG_SH_SPI) += sh_spi.o COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) diff --git a/drivers/spi/sh_spi.c b/drivers/spi/sh_spi.c new file mode 100644 index 0000000..ba43bec --- /dev/null +++ b/drivers/spi/sh_spi.c @@ -0,0 +1,261 @@ +/* + * SH SPI driver + * + * Copyright (C) 2011 Renesas Solutions Corp. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + * + */ + +#include <common.h> +#include <malloc.h> +#include <spi.h> +#include <asm/io.h> +#include "sh_spi.h" + +static void sh_spi_write(unsigned long data, unsigned long *reg) +{ + writel(data, reg); +} + +static unsigned long sh_spi_read(unsigned long *reg) +{ + return readl(reg); +} + +static void sh_spi_set_bit(unsigned long val, unsigned long *reg) +{ + unsigned long tmp; + + tmp = sh_spi_read(reg); + tmp |= val; + sh_spi_write(tmp, reg); +} + +static void sh_spi_clear_bit(unsigned long val, unsigned long *reg) +{ + unsigned long tmp; + + tmp = sh_spi_read(reg); + tmp &= ~val; + sh_spi_write(tmp, reg); +} + +static void clear_fifo(struct sh_spi *ss) +{ + sh_spi_set_bit(SH_SPI_RSTF, &ss->regs->cr2); + sh_spi_clear_bit(SH_SPI_RSTF, &ss->regs->cr2); +} + +static int recvbuf_wait(struct sh_spi *ss) +{ + while (sh_spi_read(&ss->regs->cr1) & SH_SPI_RBE) { + if (ctrlc()) + return 1; + udelay(10); + } + return 0; +} + +static int write_fifo_empty_wait(struct sh_spi *ss) +{ + while (!(sh_spi_read(&ss->regs->cr1) & SH_SPI_TBE)) { + if (ctrlc()) + return 1; + udelay(10); + } + return 0; +} + +void spi_init(void) +{ +} + +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, + unsigned int max_hz, unsigned int mode) +{ + struct sh_spi *ss; + + if (!spi_cs_is_valid(bus, cs)) + return NULL; + + ss = malloc(sizeof(struct spi_slave)); + if (!ss) + return NULL; + + ss->slave.bus = bus; + ss->slave.cs = cs; + ss->regs = (struct sh_spi_regs *)CONFIG_SH_SPI_BASE; + + /* SPI sycle stop */ + sh_spi_write(0xfe, &ss->regs->cr1); + /* CR1 init */ + sh_spi_write(0x00, &ss->regs->cr1); + /* CR3 init */ + sh_spi_write(0x00, &ss->regs->cr3); + + clear_fifo(ss); + + /* 1/8 clock */ + sh_spi_write(sh_spi_read(&ss->regs->cr2) | 0x07, &ss->regs->cr2); + udelay(10); + + return &ss->slave; +} + +void spi_free_slave(struct spi_slave *slave) +{ + struct sh_spi *spi = to_sh_spi(slave); + + free(spi); +} + +int spi_claim_bus(struct spi_slave *slave) +{ + return 0; +} + +void spi_release_bus(struct spi_slave *slave) +{ + struct sh_spi *ss = to_sh_spi(slave); + + sh_spi_write(sh_spi_read(&ss->regs->cr1) & + ~(SH_SPI_SSA | SH_SPI_SSDB | SH_SPI_SSD), &ss->regs->cr1); +} + +static int sh_spi_send(struct sh_spi *ss, const unsigned char *tx_data, + unsigned int len, unsigned long flags) +{ + int i, cur_len, ret = 0; + int remain = (int)len; + unsigned long tmp; + + if (len >= SH_SPI_FIFO_SIZE) + sh_spi_set_bit(SH_SPI_SSA, &ss->regs->cr1); + + while (remain > 0) { + cur_len = (remain < SH_SPI_FIFO_SIZE) ? + remain : SH_SPI_FIFO_SIZE; + for (i = 0; i < cur_len && + !(sh_spi_read(&ss->regs->cr4) & SH_SPI_WPABRT) && + !(sh_spi_read(&ss->regs->cr1) & SH_SPI_TBF); + i++) + sh_spi_write(tx_data[i], &ss->regs->tbr_rbr); + + cur_len = i; + + if (sh_spi_read(&ss->regs->cr4) & SH_SPI_WPABRT) { + /* Abort the transaction */ + flags |= SPI_XFER_END; + sh_spi_set_bit(SH_SPI_WPABRT, &ss->regs->cr4); + ret = 1; + break; + } + + remain -= cur_len; + tx_data += cur_len; + + if (remain > 0) + write_fifo_empty_wait(ss); + } + + if (flags & SPI_XFER_END) { + tmp = sh_spi_read(&ss->regs->cr1); + tmp = tmp & ~(SH_SPI_SSD | SH_SPI_SSDB); + sh_spi_write(tmp, &ss->regs->cr1); + sh_spi_set_bit(SH_SPI_SSA, &ss->regs->cr1); + udelay(100); + write_fifo_empty_wait(ss); + } + + return ret; +} + +static int sh_spi_receive(struct sh_spi *ss, unsigned char *rx_data, + unsigned int len, unsigned long flags) +{ + int i; + unsigned long tmp; + + if (len > SH_SPI_MAX_BYTE) + sh_spi_write(SH_SPI_MAX_BYTE, &ss->regs->cr3); + else + sh_spi_write(len, &ss->regs->cr3); + + tmp = sh_spi_read(&ss->regs->cr1); + tmp = tmp & ~(SH_SPI_SSD | SH_SPI_SSDB); + sh_spi_write(tmp, &ss->regs->cr1); + sh_spi_set_bit(SH_SPI_SSA, &ss->regs->cr1); + + for (i = 0; i < len; i++) { + if (recvbuf_wait(ss)) + return 0; + + rx_data[i] = (unsigned char)sh_spi_read(&ss->regs->tbr_rbr); + } + sh_spi_write(0, &ss->regs->cr3); + + return 0; +} + +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, + void *din, unsigned long flags) +{ + struct sh_spi *ss = to_sh_spi(slave); + const unsigned char *tx_data = dout; + unsigned char *rx_data = din; + unsigned int len = bitlen / 8; + int ret = 0; + + if (flags & SPI_XFER_BEGIN) + sh_spi_write(sh_spi_read(&ss->regs->cr1) & ~SH_SPI_SSA, + &ss->regs->cr1); + + if (tx_data) + ret = sh_spi_send(ss, tx_data, len, flags); + + if (ret == 0 && rx_data) + ret = sh_spi_receive(ss, rx_data, len, flags); + + if (flags & SPI_XFER_END) { + sh_spi_set_bit(SH_SPI_SSD, &ss->regs->cr1); + udelay(100); + + sh_spi_clear_bit(SH_SPI_SSA | SH_SPI_SSDB | SH_SPI_SSD, + &ss->regs->cr1); + clear_fifo(ss); + } + + return ret; +} + +int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{ + /* This driver supports "bus = 0" and "cs = 0" only. */ + if (!bus && !cs) + return 1; + else + return 0; +} + +void spi_cs_activate(struct spi_slave *slave) +{ + +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + +} + diff --git a/drivers/spi/sh_spi.h b/drivers/spi/sh_spi.h new file mode 100644 index 0000000..b1cf98c --- /dev/null +++ b/drivers/spi/sh_spi.h @@ -0,0 +1,79 @@ +/* + * SH SPI driver + * + * Copyright (C) 2011 Renesas Solutions Corp. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + * + */ + +#ifndef __SH_SPI_H__ +#define __SH_SPI_H__ + +#include <spi.h> + +struct sh_spi_regs { + unsigned long tbr_rbr; + unsigned long resv1; + unsigned long cr1; + unsigned long resv2; + unsigned long cr2; + unsigned long resv3; + unsigned long cr3; + unsigned long resv4; + unsigned long cr4; +}; + +/* CR1 */ +#define SH_SPI_TBE 0x80 +#define SH_SPI_TBF 0x40 +#define SH_SPI_RBE 0x20 +#define SH_SPI_RBF 0x10 +#define SH_SPI_PFONRD 0x08 +#define SH_SPI_SSDB 0x04 +#define SH_SPI_SSD 0x02 +#define SH_SPI_SSA 0x01 + +/* CR2 */ +#define SH_SPI_RSTF 0x80 +#define SH_SPI_LOOPBK 0x40 +#define SH_SPI_CPOL 0x20 +#define SH_SPI_CPHA 0x10 +#define SH_SPI_L1M0 0x08 + +/* CR3 */ +#define SH_SPI_MAX_BYTE 0xFF + +/* CR4 */ +#define SH_SPI_TBEI 0x80 +#define SH_SPI_TBFI 0x40 +#define SH_SPI_RBEI 0x20 +#define SH_SPI_RBFI 0x10 +#define SH_SPI_WPABRT 0x04 +#define SH_SPI_SSS 0x01 + +#define SH_SPI_FIFO_SIZE 32 + +struct sh_spi { + struct spi_slave slave; + struct sh_spi_regs *regs; +}; + +static inline struct sh_spi *to_sh_spi(struct spi_slave *slave) +{ + return container_of(slave, struct sh_spi, slave); +} + +#endif + diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index e6b60cf..bf2fdd6 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -136,6 +136,7 @@ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #define CONFIG_DDR_SPD +#define CONFIG_DDR_ECC #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER #define CONFIG_MEM_INIT_VALUE 0xDeadBeef @@ -654,12 +655,12 @@ */ #include <config_cmd_default.h> +#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_PING #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ #define CONFIG_CMD_SETEXPR #define CONFIG_CMD_REGINFO diff --git a/include/configs/MigoR.h b/include/configs/MigoR.h index 8a6b8d0..7d9368c 100644 --- a/include/configs/MigoR.h +++ b/include/configs/MigoR.h @@ -59,6 +59,7 @@ #define MIGO_R_FLASH_BASE_1 (0xA0000000) #define MIGO_R_FLASH_BANK_SIZE (64 * 1024 * 1024) +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */ diff --git a/include/configs/ap325rxa.h b/include/configs/ap325rxa.h index e7f37f5..711dd3c 100644 --- a/include/configs/ap325rxa.h +++ b/include/configs/ap325rxa.h @@ -63,6 +63,8 @@ #define AP325RXA_FLASH_BASE_1 (0xA0000000) #define AP325RXA_FLASH_BANK_SIZE (128 * 1024 * 1024) +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 + /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ diff --git a/include/configs/espt.h b/include/configs/espt.h index 26389ed..ad3c335 100644 --- a/include/configs/espt.h +++ b/include/configs/espt.h @@ -56,6 +56,7 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_CONS_SCIF0 1 +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */ diff --git a/include/configs/mpr2.h b/include/configs/mpr2.h index 311f524..f32899f 100644 --- a/include/configs/mpr2.h +++ b/include/configs/mpr2.h @@ -58,6 +58,8 @@ #define CONFIG_SYS_MONITOR_LEN (128 * 1024) #define CONFIG_SYS_MALLOC_LEN (256 * 1024) +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 + /* Memory */ #define CONFIG_SYS_SDRAM_BASE 0x8C000000 #define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) diff --git a/include/configs/ms7720se.h b/include/configs/ms7720se.h index 5304237..dd79b2d 100644 --- a/include/configs/ms7720se.h +++ b/include/configs/ms7720se.h @@ -52,6 +52,7 @@ #define MS7720SE_FLASH_BASE_1 0xA0000000 #define MS7720SE_FLASH_BANK_SIZE (8 * 1024 * 1024) +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */ diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h index 1ddadf6..c8d04f7 100644 --- a/include/configs/ms7722se.h +++ b/include/configs/ms7722se.h @@ -57,6 +57,7 @@ #define MS7722SE_FLASH_BASE_1 (0xA0000000) #define MS7722SE_FLASH_BANK_SIZE (8*1024 * 1024) +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */ diff --git a/include/configs/ms7750se.h b/include/configs/ms7750se.h index 9b43acb..16fb0d4 100644 --- a/include/configs/ms7750se.h +++ b/include/configs/ms7750se.h @@ -64,6 +64,7 @@ /* List of legal baudrate settings for this board */ #define CONFIG_SYS_BAUDRATE_TABLE { 115200, 57600, 38400, 19200, 9600 } +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 #define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE) #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - 0x100000) diff --git a/include/configs/r2dplus.h b/include/configs/r2dplus.h index 8689513..5534b49 100644 --- a/include/configs/r2dplus.h +++ b/include/configs/r2dplus.h @@ -40,6 +40,7 @@ #define CONFIG_SYS_SDRAM_BASE (0x8C000000) #define CONFIG_SYS_SDRAM_SIZE (0x04000000) +#define CONFIG_SYS_TEXT_BASE 0x0FFC0000 #define CONFIG_SYS_LONGHELP #define CONFIG_SYS_PROMPT "=> " #define CONFIG_SYS_CBSIZE 256 diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h index 802416f..e1febf3 100644 --- a/include/configs/r7780mp.h +++ b/include/configs/r7780mp.h @@ -60,6 +60,7 @@ /* check for keypress on bootdelay==0 */ /*#define CONFIG_ZERO_BOOTDELAY_CHECK*/ +#define CONFIG_SYS_TEXT_BASE 0x0FFC0000 #define CONFIG_SYS_SDRAM_BASE (0x08000000) #define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) diff --git a/include/configs/rsk7203.h b/include/configs/rsk7203.h index b3feaa8..0802140 100644 --- a/include/configs/rsk7203.h +++ b/include/configs/rsk7203.h @@ -54,6 +54,7 @@ #define RSK7203_FLASH_BASE_1 0x20000000 /* Non cache */ #define RSK7203_FLASH_BANK_SIZE (4 * 1024 * 1024) +#define CONFIG_SYS_TEXT_BASE 0x0C7C0000 #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */ diff --git a/include/configs/sh7757lcr.h b/include/configs/sh7757lcr.h new file mode 100644 index 0000000..9799767 --- /dev/null +++ b/include/configs/sh7757lcr.h @@ -0,0 +1,146 @@ +/* + * Configuation settings for the sh7757lcr board + * + * Copyright (C) 2011 Renesas Solutions Corp. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __SH7757LCR_H +#define __SH7757LCR_H + +#undef DEBUG +#define CONFIG_SH 1 +#define CONFIG_SH4A 1 +#define CONFIG_SH_32BIT 1 +#define CONFIG_CPU_SH7757 1 +#define CONFIG_SH7757LCR 1 + +#define CONFIG_SYS_TEXT_BASE 0x8ef80000 +#define CONFIG_SYS_LDSCRIPT "board/renesas/sh7757lcr/u-boot.lds" + +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_NFS +#define CONFIG_CMD_DFL +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SF +#define CONFIG_CMD_RUN +#define CONFIG_CMD_SAVEENV +#define CONFIG_CMD_MD5SUM +#define CONFIG_MD5 +#define CONFIG_CMD_LOADS + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTARGS "console=ttySC2,115200 root=/dev/nfs ip=dhcp" + +#define CONFIG_VERSION_VARIABLE +#undef CONFIG_SHOW_BOOT_PROGRESS + +/* MEMORY */ +#define SH7757LCR_SDRAM_BASE (0x80000000) +#define SH7757LCR_SDRAM_SIZE (240 * 1024 * 1024) +#define SH7757LCR_SDRAM_ECC_SETTING 0x0f000000 /* 240MByte */ +#define SH7757LCR_SDRAM_DVC_SIZE (16 * 1024 * 1024) + +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_PBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE 512 +#define CONFIG_SYS_BAUDRATE_TABLE { 115200 } + +/* SCIF */ +#define CONFIG_SCIF_CONSOLE 1 +#define CONFIG_CONS_SCIF2 1 +#undef CONFIG_SYS_CONSOLE_INFO_QUIET +#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE + +#define CONFIG_SYS_MEMTEST_START (SH7757LCR_SDRAM_BASE) +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ + 224 * 1024 * 1024) +#undef CONFIG_SYS_ALT_MEMTEST +#undef CONFIG_SYS_MEMTEST_SCRATCH +#undef CONFIG_SYS_LOADS_BAUD_CHANGE + +#define CONFIG_SYS_SDRAM_BASE (SH7757LCR_SDRAM_BASE) +#define CONFIG_SYS_SDRAM_SIZE (SH7757LCR_SDRAM_SIZE) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + \ + (128 + 16) * 1024 * 1024) + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) +#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) + +/* FLASH */ +#define CONFIG_SYS_NO_FLASH + +/* Ether */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_SH_ETHER 1 +#define CONFIG_SH_ETHER_USE_PORT 0 +#define CONFIG_SH_ETHER_PHY_ADDR 1 +#define CONFIG_SH_ETHER_CACHE_WRITEBACK 1 + +#define SH7757LCR_ETHERNET_MAC_BASE_SPI 0x000b0000 +#define SH7757LCR_SPI_SECTOR_SIZE (64 * 1024) +#define SH7757LCR_ETHERNET_MAC_BASE SH7757LCR_ETHERNET_MAC_BASE_SPI +#define SH7757LCR_ETHERNET_MAC_SIZE 17 +#define SH7757LCR_ETHERNET_NUM_CH 2 +#define BOARD_LATE_INIT 1 + +/* Gigabit Ether */ +#define SH7757LCR_GIGA_ETHERNET_NUM_CH 2 + +/* SPI */ +#define CONFIG_SH_SPI 1 +#define CONFIG_SH_SPI_BASE 0xfe002000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO 1 + +/* SH7757 board */ +#define SH7757LCR_SDRAM_PHYS_TOP 0x40000000 +#define SH7757LCR_GRA_OFFSET 0x1f000000 +#define SH7757LCR_PCIEBRG_ADDR_B0 0x000a0000 +#define SH7757LCR_PCIEBRG_SIZE_B0 (64 * 1024) +#define SH7757LCR_PCIEBRG_ADDR 0x00090000 +#define SH7757LCR_PCIEBRG_SIZE (96 * 1024) + +/* ENV setting */ +#define CONFIG_ENV_IS_EMBEDDED +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SECT_SIZE (64 * 1024) +#define CONFIG_ENV_ADDR (0x00080000) +#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR) +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netboot=bootp; bootm\0" + +/* Board Clock */ +#define CONFIG_SYS_CLK_FREQ 48000000 +#define CONFIG_SYS_TMU_CLK_DIV 4 +#define CONFIG_SYS_HZ 1000 +#endif /* __SH7757LCR_H */ diff --git a/include/configs/sh7763rdp.h b/include/configs/sh7763rdp.h index 209cb88..6a08413 100644 --- a/include/configs/sh7763rdp.h +++ b/include/configs/sh7763rdp.h @@ -56,6 +56,7 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_CONS_SCIF2 1 +#define CONFIG_SYS_TEXT_BASE 0x8FFC0000 #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */ diff --git a/include/configs/sh7785lcr.h b/include/configs/sh7785lcr.h index a95a759..8eb9a12 100644 --- a/include/configs/sh7785lcr.h +++ b/include/configs/sh7785lcr.h @@ -63,6 +63,7 @@ /* MEMORY */ #if defined(CONFIG_SH_32BIT) +#define CONFIG_SYS_TEXT_BASE 0x8FF80000 /* 0x40000000 - 0x47FFFFFF does not use */ #define CONFIG_SH_SDRAM_OFFSET (0x8000000) #define SH7785LCR_SDRAM_PHYS_BASE (0x40000000 + CONFIG_SH_SDRAM_OFFSET) @@ -72,6 +73,7 @@ #define SH7785LCR_FLASH_BANK_SIZE (64 * 1024 * 1024) #define SH7785LCR_USB_BASE (0xa6000000) #else +#define CONFIG_SYS_TEXT_BASE 0x0FF80000 #define SH7785LCR_SDRAM_BASE (0x08000000) #define SH7785LCR_SDRAM_SIZE (128 * 1024 * 1024) #define SH7785LCR_FLASH_BASE_1 (0xa0000000) diff --git a/include/configs/shmin.h b/include/configs/shmin.h index bee7e44..3a008f0 100644 --- a/include/configs/shmin.h +++ b/include/configs/shmin.h @@ -56,6 +56,7 @@ #define SHMIN_SDRAM_BASE (0x8C000000) #define SHMIN_FLASH_BASE_1 (0xA0000000) +#define CONFIG_SYS_TEXT_BASE 0x8DFB0000 #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 07e0e0b..ea137c7 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -694,14 +694,21 @@ /* SPMR - System PLL Mode Register */ #define SPMR_LBIUCM 0x80000000 +#define SPMR_LBIUCM_SHIFT 31 #define SPMR_DDRCM 0x40000000 +#define SPMR_DDRCM_SHIFT 30 #define SPMR_SPMF 0x0F000000 +#define SPMR_SPMF_SHIFT 24 #define SPMR_CKID 0x00800000 #define SPMR_CKID_SHIFT 23 #define SPMR_COREPLL 0x007F0000 +#define SPMR_COREPLL_SHIFT 16 #define SPMR_CEVCOD 0x000000C0 +#define SPMR_CEVCOD_SHIFT 6 #define SPMR_CEPDF 0x00000020 +#define SPMR_CEPDF_SHIFT 5 #define SPMR_CEPMF 0x0000001F +#define SPMR_CEPMF_SHIFT 0 /* OCCR - Output Clock Control Register */ diff --git a/include/pci.h b/include/pci.h index e80b6bd..c6b264b 100644 --- a/include/pci.h +++ b/include/pci.h @@ -420,6 +420,8 @@ struct pci_controller { /* Used by ppc405 autoconfig*/ struct pci_region *pci_fb; int current_busno; + + void *priv_data; }; extern __inline__ void pci_set_ops(struct pci_controller *hose, |