summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/powerpc/cpu/mpc8xx/scc.c12
-rw-r--r--arch/powerpc/cpu/mpc8xx/serial.c2
-rw-r--r--board/fads/fads.c65
-rw-r--r--board/fads/fads.h5
-rw-r--r--board/fads/lamp.c4
-rw-r--r--board/fads/pcmcia.c13
-rw-r--r--boards.cfg4
-rw-r--r--include/commproc.h88
-rw-r--r--include/configs/ADS860.h60
-rw-r--r--include/configs/FADS823.h472
-rw-r--r--include/configs/FADS850SAR.h415
-rw-r--r--include/configs/FADS860T.h58
-rw-r--r--include/pcmcia.h2
13 files changed, 1 insertions, 1199 deletions
diff --git a/arch/powerpc/cpu/mpc8xx/scc.c b/arch/powerpc/cpu/mpc8xx/scc.c
index 94c9969..647f058 100644
--- a/arch/powerpc/cpu/mpc8xx/scc.c
+++ b/arch/powerpc/cpu/mpc8xx/scc.c
@@ -461,18 +461,6 @@ static int scc_init (struct eth_device *dev, bd_t * bis)
#error Configuration Error: exactly ONE of PB_ENET_TENA, PC_ENET_TENA must be defined
#endif
-#if defined(CONFIG_ADS) && defined(CONFIG_MPC860)
- /*
- * Port C is used to control the PHY,MC68160.
- */
- immr->im_ioport.iop_pcdir |=
- (PC_ENET_ETHLOOP | PC_ENET_TPFLDL | PC_ENET_TPSQEL);
-
- immr->im_ioport.iop_pcdat |= PC_ENET_TPFLDL;
- immr->im_ioport.iop_pcdat &= ~(PC_ENET_ETHLOOP | PC_ENET_TPSQEL);
- *((uint *) BCSR1) &= ~BCSR1_ETHEN;
-#endif /* MPC860ADS */
-
#ifdef CONFIG_RPXCLASSIC
*((uchar *) BCSR0) &= ~BCSR0_ETHLPBK;
*((uchar *) BCSR0) |= (BCSR0_ETHEN | BCSR0_COLTEST | BCSR0_FULLDPLX);
diff --git a/arch/powerpc/cpu/mpc8xx/serial.c b/arch/powerpc/cpu/mpc8xx/serial.c
index cb48ed9..f7ca11e 100644
--- a/arch/powerpc/cpu/mpc8xx/serial.c
+++ b/arch/powerpc/cpu/mpc8xx/serial.c
@@ -173,7 +173,7 @@ static int smc_init (void)
# endif
#endif
-#if defined(CONFIG_FADS) || defined(CONFIG_ADS)
+#if defined(CONFIG_FADS)
/* Enable RS232 */
#if defined(CONFIG_8xx_CONS_SMC1)
*((uint *) BCSR1) &= ~BCSR1_RS232EN_1;
diff --git a/board/fads/fads.c b/board/fads/fads.c
index 89dd9ef..fdb46b1 100644
--- a/board/fads/fads.c
+++ b/board/fads/fads.c
@@ -210,11 +210,7 @@ static int _draminit (uint base, uint noMbytes, uint edo, uint delay)
switch (noMbytes) {
case 4: /* 4 Mbyte uses only CS2 */
-#ifdef CONFIG_ADS
- memctl->memc_mamr = 0xc0a21114;
-#else
memctl->memc_mamr = 0x13a01114; /* PTA 0x13 AMA 010 */
-#endif
memctl->memc_or2 = 0xffc00800; /* 4M */
break;
@@ -226,11 +222,7 @@ static int _draminit (uint base, uint noMbytes, uint edo, uint delay)
break;
case 16: /* 16 Mbyte uses only CS2 */
-#ifdef CONFIG_ADS /* XXX: why PTA=0x60 only in 16M case? - NTL */
- memctl->memc_mamr = 0x60b21114; /* PTA 0x60 AMA 011 */
-#else
memctl->memc_mamr = 0x13b01114; /* PTA 0x13 AMA 011 */
-#endif
memctl->memc_or2 = 0xff000800; /* 16M */
break;
@@ -674,42 +666,6 @@ int testdram (void)
* Check Board Identity:
*/
-#if defined(CONFIG_FADS) && defined(CONFIG_SYS_DAUGHTERBOARD)
-static void checkdboard(void)
-{
- /* get db type from BCSR 3 */
- uint k = (*((uint *)BCSR3) >> 24) & 0x3f;
-
- puts (" with db ");
-
- switch(k) {
- case 0x03 :
- puts ("MPC823");
- break;
- case 0x20 :
- puts ("MPC801");
- break;
- case 0x21 :
- puts ("MPC850");
- break;
- case 0x22 :
- puts ("MPC821, MPC860 / MPC860SAR / MPC860T");
- break;
- case 0x23 :
- puts ("MPC860SAR");
- break;
- case 0x24 :
- case 0x2A :
- puts ("MPC860T");
- break;
- case 0x3F :
- puts ("MPC850SAR");
- break;
- default : printf("0x%x", k);
- }
-}
-#endif /* defined(CONFIG_FADS) && defined(CONFIG_SYS_DAUGHTERBOARD) */
-
int checkboard (void)
{
#if defined(CONFIG_MPC86xADS)
@@ -732,27 +688,12 @@ int checkboard (void)
puts (" rev ");
switch (r) {
-#if defined(CONFIG_ADS)
- case 0x00:
- puts ("ENG - this board sucks, check the errata, not supported\n");
- return -1;
- case 0x01:
- puts ("PILOT - warning, read errata \n");
- break;
- case 0x02:
- puts ("A - warning, read errata \n");
- break;
- case 0x03:
- puts ("B\n");
- break;
-#else /* FADS */
case 0x00:
puts ("ENG\n");
break;
case 0x01:
puts ("PILOT\n");
break;
-#endif /* CONFIG_ADS */
default:
printf ("unknown (0x%x)\n", r);
return -1;
@@ -865,12 +806,6 @@ int pcmcia_init(void)
#endif
case 5:
printf("; using 5V");
-#ifdef CONFIG_ADS
- /*
- ** Enable 5 volt Vcc.
- */
- *((uint *)BCSR1) &= ~BCSR1_PCCVCCON;
-#endif
#ifdef CONFIG_FADS
/*
** Enable 5 volt Vcc.
diff --git a/board/fads/fads.h b/board/fads/fads.h
index fa49080..1be00b9 100644
--- a/board/fads/fads.h
+++ b/board/fads/fads.h
@@ -66,13 +66,8 @@
* motherboard and FEC Ethernet on daughterboard. All new PQ1 chips have
* got FEC so FEC is the default.
*/
-#ifndef CONFIG_ADS
#undef CONFIG_SCC1_ENET /* Disable SCC1 ethernet */
#define CONFIG_FEC_ENET /* Use FEC ethernet */
-#else /* Old ADS has not got FEC option */
-#define CONFIG_SCC1_ENET /* Use SCC1 ethernet */
-#undef CONFIG_FEC_ENET /* No FEC ethernet */
-#endif /* !CONFIG_ADS */
#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
diff --git a/board/fads/lamp.c b/board/fads/lamp.c
index 4e58291..ffcc2b3 100644
--- a/board/fads/lamp.c
+++ b/board/fads/lamp.c
@@ -1,7 +1,5 @@
#include <config.h>
-#ifndef CONFIG_ADS /* Old ADS has not got any user-controllable LED */
-
#include <common.h>
void
@@ -43,5 +41,3 @@ fast_blink(unsigned int n)
signal_delay(0x00100000);
}
}
-
-#endif /* !CONFIG_ADS */
diff --git a/board/fads/pcmcia.c b/board/fads/pcmcia.c
index 99fe0b4..996f032 100644
--- a/board/fads/pcmcia.c
+++ b/board/fads/pcmcia.c
@@ -14,11 +14,7 @@
#ifdef CONFIG_PCMCIA
-#ifdef CONFIG_ADS
-#define PCMCIA_BOARD_MSG "ADS"
-#else
#define PCMCIA_BOARD_MSG "FADS"
-#endif
int pcmcia_voltage_set(int slot, int vcc, int vpp)
{
@@ -33,9 +29,6 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
switch(vcc) {
case 0: reg = 0; break;
-#ifdef CONFIG_ADS
- case 50: reg = BCSR1_PCCVCCON; break;
-#endif
#ifdef CONFIG_FADS
case 33: reg = BCSR1_PCCVCC0 | BCSR1_PCCVCC1; break;
case 50: reg = BCSR1_PCCVCC1; break;
@@ -45,9 +38,6 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
/* first, turn off all power */
-#ifdef CONFIG_ADS
- *((uint *)BCSR1) |= BCSR1_PCCVCCON;
-#endif
#ifdef CONFIG_FADS
*((uint *)BCSR1) &= ~(BCSR1_PCCVCC0 | BCSR1_PCCVCC1);
#endif
@@ -55,9 +45,6 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
/* enable new powersettings */
-#ifdef CONFIG_ADS
- *((uint *)BCSR1) &= ~reg;
-#endif
#ifdef CONFIG_FADS
*((uint *)BCSR1) |= reg;
#endif
diff --git a/boards.cfg b/boards.cfg
index e411a7b..2125e90 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -1248,7 +1248,3 @@ Orphan powerpc mpc8260 - - -
Orphan powerpc mpc8260 - - rpxsuper RPXsuper - -
Orphan powerpc mpc8xx - - - RPXClassic - -
Orphan powerpc mpc8xx - - - RPXlite - -
-Orphan powerpc mpc8xx - - fads ADS860 - -
-Orphan powerpc mpc8xx - - fads FADS823 - -
-Orphan powerpc mpc8xx - - fads FADS850SAR - -
-Orphan powerpc mpc8xx - - fads FADS860T - -
diff --git a/include/commproc.h b/include/commproc.h
index e3bc6d6..605aac2 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -429,38 +429,6 @@ typedef struct scc_enet {
* #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
**********************************************************************/
-
-/*** ADS *************************************************************/
-
-#if defined(CONFIG_MPC860) && defined(CONFIG_ADS)
-/* This ENET stuff is for the MPC860ADS with ethernet on SCC1.
- */
-
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0200)
-
-#define PB_ENET_TENA ((uint)0x00001000)
-
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000002c)
-
-/* 68160 PHY control */
-
-#define PC_ENET_ETHLOOP ((ushort)0x0800)
-#define PC_ENET_TPFLDL ((ushort)0x0400)
-#define PC_ENET_TPSQEL ((ushort)0x0200)
-
-#endif /* MPC860ADS */
-
/*** BSEIP **********************************************************/
#ifdef CONFIG_BSEIP
@@ -563,62 +531,6 @@ typedef struct scc_enet {
#endif
-/*** FADS823 ********************************************************/
-
-#if defined(CONFIG_MPC823FADS) && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC823FADS with ethernet on SCC2.
- */
-#ifdef CONFIG_SCC2_ENET
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define CPMVEC_ENET CPMVEC_SCC2
-#endif
-
-#ifdef CONFIG_SCC1_ENET
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define CPMVEC_ENET CPMVEC_SCC1
-#endif
-
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0400)
-#define PA_ENET_RCLK ((ushort)0x0200)
-
-#define PB_ENET_TENA ((uint)0x00002000)
-
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002e00)
-
-#endif /* CONFIG_FADS823FADS */
-
-/*** FADS850SAR ********************************************************/
-
-#if defined(CONFIG_MPC850SAR) && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC850SAR with ethernet on SCC2. Some of
- * this may be unique to the FADS850SAR configuration.
- * Note TENA is on Port B.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00) /* RCLK-CLK2, TCLK-CLK4 */
-#endif /* CONFIG_FADS850SAR */
-
/*** FADS860T********************************************************/
#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x)
diff --git a/include/configs/ADS860.h b/include/configs/ADS860.h
deleted file mode 100644
index 82ea172..0000000
--- a/include/configs/ADS860.h
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- * A collection of structures, addresses, and values associated with
- * the Motorola 860 ADS board. Copied from the MBX stuff.
- * Magnus Damm added defines for 8xxrom and extended bd_info.
- * Helmut Buchsbaum added bitvalues for BCSRx
- *
- * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
- *
- * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
- *
- * Values common to all FADS family boards are in board/fads/fads.h
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* Board type */
-#define CONFIG_ADS 1 /* Old Motorola MPC821/860ADS */
-
-/* Processor type */
-#define CONFIG_MPC860 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE 38400 /* Console baudrate */
-
-#if 0
-#define CONFIG_SYS_8XX_FACT 1526 /* 32.768 kHz crystal on XTAL/EXTAL */
-#else
-#define CONFIG_SYS_8XX_FACT 12 /* 4 MHz oscillator on EXTCLK */
-#endif
-
-#define CONFIG_SYS_PLPRCR (((CONFIG_SYS_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-#define CONFIG_DRAM_50MHZ 1
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_PING
-
-/* This is picked up again in fads.h */
-#define FADS_COMMANDS_ALREADY_DEFINED
-
-#include "../../board/fads/fads.h"
-
-#define CONFIG_SYS_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/FADS823.h b/include/configs/FADS823.h
deleted file mode 100644
index 50de4ea..0000000
--- a/include/configs/FADS823.h
+++ /dev/null
@@ -1,472 +0,0 @@
- /*
- * A collection of structures, addresses, and values associated with
- * the Motorola 860T FADS board. Copied from the MBX stuff.
- * Magnus Damm added defines for 8xxrom and extended bd_info.
- * Helmut Buchsbaum added bitvalues for BCSRx
- *
- * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
- */
-
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia io remapping
- * ff010000 -> ff01ffff : BCSR connected to CS1, setup by U-Boot
- * ff000000 -> ff00ffff : IMAP internal in the cpu
- * e0000000 -> f3ffffff : pcmcia memory remapping by m8xx_pcmcia
- * fe000000 -> fe1fffff : flash connected to CS0, setup by U-Boot
- * 00000000 -> nnnnnnnn : sdram/dram setup by U-Boot
-*/
-
-#define CONFIG_SYS_PCMCIA_IO_ADDR 0xff020000
-#define CONFIG_SYS_PCMCIA_IO_SIZE 0x10000
-#define CONFIG_SYS_PCMCIA_MEM_ADDR 0xe0000000
-#define CONFIG_SYS_PCMCIA_MEM_SIZE 0x10000
-#define CONFIG_SYS_IMMR 0xFF000000
-#define CONFIG_SYS_SDRAM_SIZE (4<<20) /* standard FADS has 4M */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x02800000
-#define BCSR_ADDR ((uint) 0xff010000)
-#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#define CONFIG_ETHADDR 08:00:22:50:70:63 /* Ethernet address */
-#define CONFIG_ENV_OVERWRITE 1 /* Overwrite the environment */
-
-#define CONFIG_VIDEO 1 /* To enable video controller support */
-#define CONFIG_HARD_I2C 1 /* To I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*#define CONFIG_PCMCIA 1 / * To enable PCMCIA support */
-
-/* Video related */
-
-#define CONFIG_VIDEO_LOGO 1 /* Show the logo */
-#define CONFIG_VIDEO_ENCODER_AD7176 1 /* Enable this encoder */
-#define CONFIG_VIDEO_ENCODER_AD7176_ADDR 0x54 /* Default on fads */
-#define CONFIG_VIDEO_SIZE (2*1024*1024)
-/* #define CONFIG_VIDEO_ADDR (gd->bd->bi_memsize - CONFIG_VIDEO_SIZE) Frame buffer address */
-
-/* Wireless 56Khz 4PPM keyboard on SMCx */
-
-/*#define CONFIG_KEYBOARD 1 */
-#define CONFIG_WL_4PPM_KEYBOARD_SMC 0 /* SMC to use (0 indexed) */
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC823 1
-#define CONFIG_MPC823FADS 1
-#define CONFIG_FADS 1
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 115200
-
-/* Set the CPU speed to 50Mhz on the FADS */
-
-#if 0
-#define MPC8XX_FACT 10 /* Multiply by 10 */
-#define MPC8XX_XIN 5000000 /* 5 MHz in */
-#else
-#define MPC8XX_FACT 10 /* Multiply by 10 */
-#define MPC8XX_XIN 5000000 /* 5 MHz in */
-#define CONFIG_SYS_PLPRCR_MF (MPC8XX_FACT-1) << 20 /* From 0 to 4095 */
-#endif
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
-#define CONFIG_LOADS_ECHO 0 /* Dont echoes received characters */
-#define CONFIG_BOOTARGS ""
-#define CONFIG_BOOTCOMMAND \
-"bootp ;" \
-"setenv bootargs console=tty0 console=ttyS0 " \
-"root=/dev/nfs nfsroot=${serverip}:${rootpath} " \
-"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:eth0:off ;" \
-"bootm"
-#else
-#define CONFIG_BOOTDELAY 0 /* autoboot disabled */
-#endif
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_NISDOMAIN
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_TIMEOFFSET
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 0 ... 16 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
- */
-#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-#if 0
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
-#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer *
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CONFIG_SYS_PLPRCR_MF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_TBS | \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_SIZE ((uint)(64 * 1024))
-
-#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */
-
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CONFIG_SYS_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR 0x13a01114
-
-/* values according to the manual */
-
-#define BCSR0 ((uint) (BCSR_ADDR + 00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_FLASH_PD_SHIFT 28
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT 23
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0 ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1 ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_MODEM_EN ((uint)0x00100000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC850
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC850 */
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS 0
-
-/*
- * MPC8xx CPM Options
- */
-#define CONFIG_SCC_ENET 1
-#define CONFIG_SCC2_ENET 1
-#undef CONFIG_FEC_ENET
-#undef CONFIG_CPM_IIC
-#undef CONFIG_UCODE_PATCH
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS 1
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CONFIG_SYS_DAUGHTERBOARD
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/FADS850SAR.h b/include/configs/FADS850SAR.h
deleted file mode 100644
index d48460b..0000000
--- a/include/configs/FADS850SAR.h
+++ /dev/null
@@ -1,415 +0,0 @@
- /*
- * A collection of structures, addresses, and values associated with
- * the Motorola 860T FADS board. Copied from the MBX stuff.
- * Magnus Damm added defines for 8xxrom and extended bd_info.
- * Helmut Buchsbaum added bitvalues for BCSRx
- *
- * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
- */
-
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom
- * ff000000 -> ff00ffff : IMAP internal in the cpu
- * fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom
- * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC850 1
-#define CONFIG_MPC850SAR 1
-#define CONFIG_FADS 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 9600
-
-#if 0
-#define MPC8XX_FACT 10 /* Multiply by 10 */
-#define MPC8XX_XIN 50000000 /* 50 MHz in */
-#else
-#define MPC8XX_FACT 12 /* Multiply by 12 */
-#define MPC8XX_XIN 4000000 /* 4 MHz in */
-#endif
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BOOTCOMMAND "bootm 02880000" /* autoboot command */
-#define CONFIG_BOOTARGS " "
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#undef CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFF000000
-#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_SIZE (4<<20) /* standard FADS has 4M */
-#define CONFIG_SYS_FLASH_BASE 0x02800000
-#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-#if 0
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
-#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer *
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << 20) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_TBS | \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-
-#define BCSR_ADDR ((uint) 0x02100000)
-#define BCSR_SIZE ((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */
-
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CONFIG_SYS_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR 0x13a01114
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR ((uint)0xff020000)
-#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
-
-#define BCSR0 ((uint) (BCSR_ADDR + 00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_FLASH_PD_SHIFT 28
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT 23
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0 ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1 ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#define BCSR4_MODEM_EN ((uint)0x00100000)
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS 0
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS 2
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CONFIG_SYS_DAUGHTERBOARD
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/FADS860T.h b/include/configs/FADS860T.h
deleted file mode 100644
index ed7484b..0000000
--- a/include/configs/FADS860T.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * A collection of structures, addresses, and values associated with
- * the Motorola 860T FADS board. Copied from the MBX stuff.
- * Magnus Damm added defines for 8xxrom and extended bd_info.
- * Helmut Buchsbaum added bitvalues for BCSRx
- *
- * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
- *
- * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
- *
- * Values common to all FADS family boards are in board/fads/fads.h
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* board type */
-#define CONFIG_FADS 1 /* old/new FADS + new ADS */
-
-/* processor type */
-#define CONFIG_MPC860T 1 /* 860T */
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 38400
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-
-#if 0 /* old FADS */
-# define CONFIG_SYS_8XX_FACT 12 /* 4 MHz oscillator on EXTCLK */
-#else /* new FADS */
-# define CONFIG_SYS_8XX_FACT 10 /* 5 MHz oscillator on EXTCLK */
-#endif
-
-#define CONFIG_SYS_PLPRCR (((CONFIG_SYS_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ 1
-
-#include "../../board/fads/fads.h"
-
-#ifdef USE_REAL_FLASH_VALUES
-/*
- * These values fit our FADS860T ...
- * The "default" behaviour with 1Mbyte initial doesn't work for us!
- */
-#undef CONFIG_SYS_OR0_PRELIM
-#undef CONFIG_SYS_BR0_PRELIM
-#define CONFIG_SYS_OR0_PRELIM 0x0FFC00D34 /* Real values for the board */
-#define CONFIG_SYS_BR0_PRELIM 0x02800001 /* Real values for the board */
-#endif
-
-#define CONFIG_SYS_DAUGHTERBOARD /* FADS has processor-specific daughterboard */
-
-#endif /* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index ce8c8ed..1ad3e63 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -24,8 +24,6 @@
/* The RPX series use SLOT_B */
#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
# define CONFIG_PCMCIA_SLOT_B
-#elif defined(CONFIG_ADS) /* The ADS board uses SLOT_A */
-# define CONFIG_PCMCIA_SLOT_A
#elif defined(CONFIG_FADS) /* The FADS series are a mess */
# if defined(CONFIG_MPC86x) || defined(CONFIG_MPC821)
# define CONFIG_PCMCIA_SLOT_A
generated by cgit v1.1 at 2024-11-25 21:06:05 +0000