summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/atmel/at91sam9x5ek/at91sam9x5ek.c1
-rw-r--r--board/renesas/koelsch/koelsch.c83
-rw-r--r--board/renesas/lager/lager.c78
-rw-r--r--doc/README.rmobile49
-rw-r--r--include/configs/at91sam9x5ek.h13
-rw-r--r--include/configs/koelsch.h41
-rw-r--r--include/configs/lager.h35
7 files changed, 272 insertions, 28 deletions
diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
index 6f67c34..17a2a40 100644
--- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c
+++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c
@@ -271,7 +271,6 @@ int board_init(void)
#endif
#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 0);
at91_spi0_hw_init(1 << 4);
#endif
diff --git a/board/renesas/koelsch/koelsch.c b/board/renesas/koelsch/koelsch.c
index 7153f65..89f5c91 100644
--- a/board/renesas/koelsch/koelsch.c
+++ b/board/renesas/koelsch/koelsch.c
@@ -16,6 +16,8 @@
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/arch/rmobile.h>
+#include <netdev.h>
+#include <miiphy.h>
#include <i2c.h>
#include "qos.h"
@@ -207,6 +209,10 @@ void s_init(void)
#define SMSTPCR7 0xE615014C
#define SCIF0_MSTP721 (1 << 21)
+#define MSTPSR8 0xE61509A0
+#define SMSTPCR8 0xE6150990
+#define ETHER_MSTP813 (1 << 13)
+
#define PMMR 0xE6060000
#define GPSR4 0xE6060014
#define IPSR14 0xE6060058
@@ -241,9 +247,16 @@ int board_early_init_f(void)
mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);
+ /* ETHER */
+ mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);
+
return 0;
}
+/* LSI pin pull-up control */
+#define PUPR5 0xe6060114
+#define PUPR5_ETH 0x3FFC0000
+#define PUPR5_ETH_MAGIC (1 << 27)
int board_init(void)
{
/* adress of boot parameters */
@@ -252,9 +265,59 @@ int board_init(void)
/* Init PFC controller */
r8a7791_pinmux_init();
+ /* ETHER Enable */
+ gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
+ gpio_request(GPIO_FN_ETH_RX_ER, NULL);
+ gpio_request(GPIO_FN_ETH_RXD0, NULL);
+ gpio_request(GPIO_FN_ETH_RXD1, NULL);
+ gpio_request(GPIO_FN_ETH_LINK, NULL);
+ gpio_request(GPIO_FN_ETH_REFCLK, NULL);
+ gpio_request(GPIO_FN_ETH_MDIO, NULL);
+ gpio_request(GPIO_FN_ETH_TXD1, NULL);
+ gpio_request(GPIO_FN_ETH_TX_EN, NULL);
+ gpio_request(GPIO_FN_ETH_TXD0, NULL);
+ gpio_request(GPIO_FN_ETH_MDC, NULL);
+ gpio_request(GPIO_FN_IRQ0, NULL);
+
+ mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH & ~PUPR5_ETH_MAGIC);
+ gpio_request(GPIO_GP_5_22, NULL); /* PHY_RST */
+ mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH_MAGIC);
+
+ gpio_direction_output(GPIO_GP_5_22, 0);
+ mdelay(20);
+ gpio_set_value(GPIO_GP_5_22, 1);
+ udelay(1);
+
return 0;
}
+#define CXR24 0xEE7003C0 /* MAC address high register */
+#define CXR25 0xEE7003C8 /* MAC address low register */
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SH_ETHER
+ int ret = -ENODEV;
+ u32 val;
+ unsigned char enetaddr[6];
+
+ ret = sh_eth_initialize(bis);
+ if (!eth_getenv_enetaddr("ethaddr", enetaddr))
+ return ret;
+
+ /* Set Mac address */
+ val = enetaddr[0] << 24 | enetaddr[1] << 16 |
+ enetaddr[2] << 8 | enetaddr[3];
+ writel(val, CXR24);
+
+ val = enetaddr[4] << 8 | enetaddr[5];
+ writel(val, CXR25);
+
+ return ret;
+#else
+ return 0;
+#endif
+}
+
int dram_init(void)
{
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
@@ -263,6 +326,20 @@ int dram_init(void)
return 0;
}
+/* koelsch has KSZ8041NL/RNL */
+#define PHY_CONTROL1 0x1E
+#define PHY_LED_MODE 0xC0000
+#define PHY_LED_MODE_ACK 0x4000
+int board_phy_config(struct phy_device *phydev)
+{
+ int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
+ ret &= ~PHY_LED_MODE;
+ ret |= PHY_LED_MODE_ACK;
+ ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
+
+ return 0;
+}
+
const struct rmobile_sysinfo sysinfo = {
CONFIG_RMOBILE_BOARD_STRING
};
@@ -280,4 +357,10 @@ int board_late_init(void)
void reset_cpu(ulong addr)
{
+ u8 val;
+
+ i2c_set_bus_num(2); /* PowerIC connected to ch2 */
+ i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
+ val |= 0x02;
+ i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
}
diff --git a/board/renesas/lager/lager.c b/board/renesas/lager/lager.c
index 5c99fc9..cdd5b32 100644
--- a/board/renesas/lager/lager.c
+++ b/board/renesas/lager/lager.c
@@ -18,6 +18,8 @@
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/arch/rmobile.h>
+#include <miiphy.h>
+#include <i2c.h>
#include "qos.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -207,6 +209,10 @@ void s_init(void)
#define SMSTPCR7 0xE615014C
#define SCIF0_MSTP721 (1 << 21)
+#define MSTPSR8 0xE61509A0
+#define SMSTPCR8 0xE6150990
+#define ETHER_MSTP813 (1 << 13)
+
#define PMMR 0xE6060000
#define GPSR4 0xE6060014
#define IPSR14 0xE6060058
@@ -242,6 +248,9 @@ int board_early_init_f(void)
mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);
+ /* ETHER */
+ mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);
+
return 0;
}
@@ -256,6 +265,68 @@ int board_init(void)
/* Init PFC controller */
r8a7790_pinmux_init();
+ /* ETHER Enable */
+ gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
+ gpio_request(GPIO_FN_ETH_RX_ER, NULL);
+ gpio_request(GPIO_FN_ETH_RXD0, NULL);
+ gpio_request(GPIO_FN_ETH_RXD1, NULL);
+ gpio_request(GPIO_FN_ETH_LINK, NULL);
+ gpio_request(GPIO_FN_ETH_REF_CLK, NULL);
+ gpio_request(GPIO_FN_ETH_MDIO, NULL);
+ gpio_request(GPIO_FN_ETH_TXD1, NULL);
+ gpio_request(GPIO_FN_ETH_TX_EN, NULL);
+ gpio_request(GPIO_FN_ETH_MAGIC, NULL);
+ gpio_request(GPIO_FN_ETH_TXD0, NULL);
+ gpio_request(GPIO_FN_ETH_MDC, NULL);
+ gpio_request(GPIO_FN_IRQ0, NULL);
+
+ gpio_request(GPIO_GP_5_31, NULL); /* PHY_RST */
+ gpio_direction_output(GPIO_GP_5_31, 0);
+ mdelay(20);
+ gpio_set_value(GPIO_GP_5_31, 1);
+ udelay(1);
+
+ return 0;
+}
+
+#define CXR24 0xEE7003C0 /* MAC address high register */
+#define CXR25 0xEE7003C8 /* MAC address low register */
+int board_eth_init(bd_t *bis)
+{
+ int ret = -ENODEV;
+
+#ifdef CONFIG_SH_ETHER
+ u32 val;
+ unsigned char enetaddr[6];
+
+ ret = sh_eth_initialize(bis);
+ if (!eth_getenv_enetaddr("ethaddr", enetaddr))
+ return ret;
+
+ /* Set Mac address */
+ val = enetaddr[0] << 24 | enetaddr[1] << 16 |
+ enetaddr[2] << 8 | enetaddr[3];
+ writel(val, CXR24);
+
+ val = enetaddr[4] << 8 | enetaddr[5];
+ writel(val, CXR25);
+
+#endif
+
+ return ret;
+}
+
+/* lager has KSZ8041NL/RNL */
+#define PHY_CONTROL1 0x1E
+#define PHY_LED_MODE 0xC0000
+#define PHY_LED_MODE_ACK 0x4000
+int board_phy_config(struct phy_device *phydev)
+{
+ int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1);
+ ret &= ~PHY_LED_MODE;
+ ret |= PHY_LED_MODE_ACK;
+ ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret);
+
return 0;
}
@@ -284,4 +355,11 @@ int board_late_init(void)
void reset_cpu(ulong addr)
{
+ u8 val;
+
+ i2c_set_bus_num(3); /* PowerIC connected to ch3 */
+ i2c_init(400000, 0);
+ i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
+ val |= 0x02;
+ i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
}
diff --git a/doc/README.rmobile b/doc/README.rmobile
index 7ec63f1..4fbbcb3 100644
--- a/doc/README.rmobile
+++ b/doc/README.rmobile
@@ -2,13 +2,15 @@ Summary
=======
This README is about U-Boot support for Renesas's ARM Cortex-A9 based RMOBILE[1]
-family of SoCs. Renesas's RMOBILE SoC family contains an ARM Cortex-A9.
+and R-Car[2]family of SoCs. Renesas's RMOBILE/R-Car SoC family contains an ARM
+Cortex-A9.
Currently the following boards are supported:
-* KMC KZM-A9-GT [2]
-
-* Atmark-Techno Armadillo-800-EVA [3]
+* KMC KZM-A9-GT [3]
+* Atmark-Techno Armadillo-800-EVA [4]
+* Renesas Electronics Lager
+* Renesas Electronics Koelsch
Toolchain
=========
@@ -17,7 +19,7 @@ ARM Cortex-A9 support ARM v7 instruction set (-march=armv7a).
But currently we compile with -march=armv5 to allow more compilers to work.
(For U-Boot code this has no performance impact.)
Because there was no compiler which is supporting armv7a not much before.
-Currently, ELDK[4], Linaro[5], CodeSourcey[6] and Emdebian[7] supports -march=armv7a
+Currently, ELDK[5], Linaro[6], CodeSourcey[7] and Emdebian[8] supports -march=armv7a
and you can get.
Build
@@ -25,13 +27,26 @@ Build
* KZM-A9-GT
-make kzm9g_config
-make
+ make kzm9g_config
+ make
* Armadillo-800-EVA
-make armadillo-800eva_config
-make
+ make armadillo-800eva_config
+ make
+
+ Note: Armadillo-800-EVA's U-Boot supports booting from SDcard only.
+ Please see "B.2 Appendix B Boot Specifications" in hardware manual.
+
+* Lager
+
+ make lager_config
+ make
+
+* Koelsch
+
+ make koelsch_config
+ make
Links
=====
@@ -40,26 +55,30 @@ Links
http://am.renesas.com/products/soc/assp/mobile/r_mobile/index.jsp
-[2] KZM-A9-GT
+[2] Renesas R-Car:
+
+http://am.renesas.com/products/soc/assp/automotive/index.jsp
+
+[3] KZM-A9-GT
http://www.kmckk.co.jp/kzma9-gt/index.html
-[3] Armadillo-800-EVA
+[4] Armadillo-800-EVA
http://armadillo.atmark-techno.com/armadillo-800-EVA
-[4] ELDK
+[5] ELDK
http://www.denx.de/wiki/view/ELDK-5/WebHome#Section_1.6.
-[5] Linaro
+[6] Linaro
http://www.linaro.org/downloads/
-[6] CodeSourcey
+[7] CodeSourcey
http://www.mentor.com/embedded-software/codesourcery
-[7] Emdebian
+[8] Emdebian
http://www.emdebian.org/crosstools.html
diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h
index ea9a50e..f0a6757 100644
--- a/include/configs/at91sam9x5ek.h
+++ b/include/configs/at91sam9x5ek.h
@@ -44,7 +44,6 @@
#define LCD_BPP LCD_COLOR16
#define LCD_OUTPUT_BPP 24
#define CONFIG_LCD_LOGO
-#undef LCD_TEST_PATTERN
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_SYS_WHITE_ON_BLACK
@@ -62,14 +61,15 @@
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
+/* no NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
@@ -101,9 +101,6 @@
#define CONFIG_SF_DEFAULT_SPEED 30000000
#endif
-/* no NOR flash */
-#define CONFIG_SYS_NO_FLASH
-
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
@@ -244,8 +241,4 @@
*/
#define CONFIG_SYS_MALLOC_LEN (512 * 1024 + 0x1000)
-#ifdef CONFIG_USE_IRQ
-#error CONFIG_USE_IRQ not supported
-#endif
-
#endif
diff --git a/include/configs/koelsch.h b/include/configs/koelsch.h
index 59c4948..f8cca5b 100644
--- a/include/configs/koelsch.h
+++ b/include/configs/koelsch.h
@@ -18,13 +18,18 @@
#include <asm/arch/rmobile.h>
-#define CONFIG_CMD_EDITENV
-#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_EDITENV
+#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_DFL
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_RUN
#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_FLASH
@@ -123,6 +128,20 @@
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_SYS_MONITOR_LEN)
+/* SH Ether */
+#define CONFIG_NET_MULTI
+#define CONFIG_SH_ETHER
+#define CONFIG_SH_ETHER_USE_PORT 0
+#define CONFIG_SH_ETHER_PHY_ADDR 0x1
+#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SH_ETHER_CACHE_WRITEBACK
+#define CONFIG_SH_ETHER_CACHE_INVALIDATE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_BITBANGMII
+#define CONFIG_BITBANGMII_MULTI
+#define CONFIG_SH_ETHER_ALIGNE_SIZE 64
+
/* Board Clock */
#define CONFIG_SYS_CLK_FREQ 10000000
#define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ
@@ -130,4 +149,22 @@
#define CONFIG_SYS_TMU_CLK_DIV 4
#define CONFIG_SYS_HZ 1000
+/* i2c */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SH
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 3
+#define CONFIG_SYS_I2C_SH_BASE0 0xE6500000
+#define CONFIG_SYS_I2C_SH_SPEED0 400000
+#define CONFIG_SYS_I2C_SH_BASE1 0xE6510000
+#define CONFIG_SYS_I2C_SH_SPEED1 400000
+#define CONFIG_SYS_I2C_SH_BASE2 0xE60B0000
+#define CONFIG_SYS_I2C_SH_SPEED2 400000
+#define CONFIG_SH_I2C_DATA_HIGH 4
+#define CONFIG_SH_I2C_DATA_LOW 5
+#define CONFIG_SH_I2C_CLOCK 10000000
+
+#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
+
#endif /* __KOELSCH_H */
diff --git a/include/configs/lager.h b/include/configs/lager.h
index 7819edd..8932825 100644
--- a/include/configs/lager.h
+++ b/include/configs/lager.h
@@ -28,6 +28,11 @@
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_RUN
#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_FLASH
@@ -127,12 +132,42 @@
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_SYS_MONITOR_LEN)
+/* SH Ether */
+#define CONFIG_NET_MULTI
+#define CONFIG_SH_ETHER
+#define CONFIG_SH_ETHER_USE_PORT 0
+#define CONFIG_SH_ETHER_PHY_ADDR 0x1
+#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SH_ETHER_ALIGNE_SIZE 64
+#define CONFIG_SH_ETHER_CACHE_WRITEBACK
+#define CONFIG_SH_ETHER_CACHE_INVALIDATE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_BITBANGMII
+#define CONFIG_BITBANGMII_MULTI
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_RCAR
+#define CONFIG_SYS_RCAR_I2C0_BASE 0xE6508000
+#define CONFIG_SYS_RCAR_I2C0_SPEED 400000
+#define CONFIG_SYS_RCAR_I2C1_BASE 0xE6518000
+#define CONFIG_SYS_RCAR_I2C1_SPEED 400000
+#define CONFIG_SYS_RCAR_I2C2_BASE 0xE6530000
+#define CONFIG_SYS_RCAR_I2C2_SPEED 400000
+#define CONFIG_SYS_RCAR_I2C3_BASE 0xE6540000
+#define CONFIG_SYS_RCAR_I2C3_SPEED 400000
+#define CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS 4
+
+#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
+
/* Board Clock */
#define CONFIG_BASE_CLK_FREQ 20000000u
#define CONFIG_SH_TMU_CLK_FREQ (CONFIG_BASE_CLK_FREQ / 2) /* EXT / 2 */
#define CONFIG_PLL1_CLK_FREQ (CONFIG_BASE_CLK_FREQ * 156 / 2)
#define CONFIG_PLL1_DIV2_CLK_FREQ (CONFIG_PLL1_CLK_FREQ / 2)
#define CONFIG_MP_CLK_FREQ (CONFIG_PLL1_DIV2_CLK_FREQ / 15)
+#define CONFIG_HP_CLK_FREQ (CONFIG_PLL1_CLK_FREQ / 12)
#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_MP_CLK_FREQ
#define CONFIG_SYS_TMU_CLK_DIV 4