summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/arm/include/asm/arch-am33xx/cpu.h51
-rw-r--r--arch/arm/include/asm/arch-am33xx/omap_gpmc.h48
-rw-r--r--arch/arm/include/asm/arch-am33xx/sys_proto.h1
-rw-r--r--arch/arm/include/asm/arch-omap3/cpu.h54
-rw-r--r--arch/arm/include/asm/arch-omap3/mem.h10
-rw-r--r--arch/arm/include/asm/arch-omap3/omap_gpmc.h36
-rw-r--r--arch/arm/include/asm/arch-omap3/sys_proto.h1
-rw-r--r--arch/arm/include/asm/arch-omap4/cpu.h45
-rw-r--r--arch/arm/include/asm/arch-omap4/sys_proto.h1
-rw-r--r--arch/arm/include/asm/arch-omap5/cpu.h45
-rw-r--r--arch/arm/include/asm/arch-omap5/sys_proto.h1
-rw-r--r--arch/arm/include/asm/omap_gpmc.h87
-rw-r--r--board/isee/igep00x0/igep00x0.c1
-rw-r--r--board/overo/overo.c1
-rw-r--r--board/ti/am335x/README53
-rw-r--r--drivers/mtd/nand/omap_elm.c6
-rw-r--r--drivers/mtd/nand/omap_gpmc.c572
-rw-r--r--include/configs/am335x_evm.h1
-rw-r--r--include/configs/am335x_igep0033.h1
-rw-r--r--include/configs/am3517_crane.h1
-rw-r--r--include/configs/am3517_evm.h1
-rw-r--r--include/configs/cm_t35.h2
-rw-r--r--include/configs/devkit8000.h2
-rw-r--r--include/configs/dig297.h2
-rw-r--r--include/configs/mcx.h1
-rw-r--r--include/configs/omap3_beagle.h2
-rw-r--r--include/configs/omap3_evm_common.h1
-rw-r--r--include/configs/omap3_igep00x0.h1
-rw-r--r--include/configs/omap3_logic.h1
-rw-r--r--include/configs/omap3_overo.h2
-rw-r--r--include/configs/omap3_pandora.h2
-rw-r--r--include/configs/omap3_zoom1.h2
-rw-r--r--include/configs/siemens-am33x-common.h1
-rw-r--r--include/configs/tam3517-common.h1
-rw-r--r--include/configs/tricorder.h2
-rw-r--r--include/linux/mtd/omap_elm.h (renamed from arch/arm/include/asm/omap_elm.h)0
-rw-r--r--include/linux/mtd/omap_gpmc.h84
37 files changed, 321 insertions, 802 deletions
diff --git a/arch/arm/include/asm/arch-am33xx/cpu.h b/arch/arm/include/asm/arch-am33xx/cpu.h
index 71bed4e..d9f0306 100644
--- a/arch/arm/include/asm/arch-am33xx/cpu.h
+++ b/arch/arm/include/asm/arch-am33xx/cpu.h
@@ -78,58 +78,7 @@
#ifndef __KERNEL_STRICT_NAMES
#ifndef __ASSEMBLY__
-struct gpmc_cs {
- u32 config1; /* 0x00 */
- u32 config2; /* 0x04 */
- u32 config3; /* 0x08 */
- u32 config4; /* 0x0C */
- u32 config5; /* 0x10 */
- u32 config6; /* 0x14 */
- u32 config7; /* 0x18 */
- u32 nand_cmd; /* 0x1C */
- u32 nand_adr; /* 0x20 */
- u32 nand_dat; /* 0x24 */
- u8 res[8]; /* blow up to 0x30 byte */
-};
-
-struct bch_res_0_3 {
- u32 bch_result_x[4];
-};
-
-struct gpmc {
- u8 res1[0x10];
- u32 sysconfig; /* 0x10 */
- u8 res2[0x4];
- u32 irqstatus; /* 0x18 */
- u32 irqenable; /* 0x1C */
- u8 res3[0x20];
- u32 timeout_control; /* 0x40 */
- u8 res4[0xC];
- u32 config; /* 0x50 */
- u32 status; /* 0x54 */
- u8 res5[0x8]; /* 0x58 */
- struct gpmc_cs cs[8]; /* 0x60, 0x90, .. */
- u8 res6[0x14]; /* 0x1E0 */
- u32 ecc_config; /* 0x1F4 */
- u32 ecc_control; /* 0x1F8 */
- u32 ecc_size_config; /* 0x1FC */
- u32 ecc1_result; /* 0x200 */
- u32 ecc2_result; /* 0x204 */
- u32 ecc3_result; /* 0x208 */
- u32 ecc4_result; /* 0x20C */
- u32 ecc5_result; /* 0x210 */
- u32 ecc6_result; /* 0x214 */
- u32 ecc7_result; /* 0x218 */
- u32 ecc8_result; /* 0x21C */
- u32 ecc9_result; /* 0x220 */
- u8 res7[12]; /* 0x224 */
- u32 testmomde_ctrl; /* 0x230 */
- u8 res8[12]; /* 0x234 */
- struct bch_res_0_3 bch_result_0_3[2]; /* 0x240 */
-};
-/* Used for board specific gpmc initialization */
-extern struct gpmc *gpmc_cfg;
#ifndef CONFIG_AM43XX
/* Encapsulating core pll registers */
diff --git a/arch/arm/include/asm/arch-am33xx/omap_gpmc.h b/arch/arm/include/asm/arch-am33xx/omap_gpmc.h
deleted file mode 100644
index 00ad1d0..0000000
--- a/arch/arm/include/asm/arch-am33xx/omap_gpmc.h
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
- * Rohit Choraria <rohitkc@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __ASM_ARCH_OMAP_GPMC_H
-#define __ASM_ARCH_OMAP_GPMC_H
-
-/* These GPMC_NAND_HW_BCHx_ECC_LAYOUT defines are based on AM33xx ELM */
-#define GPMC_NAND_HW_BCH4_ECC_LAYOUT {\
- .eccbytes = 32,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
- 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
- 28, 29, 30, 31, 32, 33},\
- .oobfree = {\
- {.offset = 34,\
- .length = 30 } } \
-}
-
-#define GPMC_NAND_HW_BCH8_ECC_LAYOUT {\
- .eccbytes = 56,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
- 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
- 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39,\
- 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,\
- 52, 53, 54, 55, 56, 57},\
- .oobfree = {\
- {.offset = 58,\
- .length = 6 } } \
-}
-
-#define GPMC_NAND_HW_BCH16_ECC_LAYOUT {\
- .eccbytes = 104,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,\
- 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27,\
- 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39,\
- 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,\
- 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63,\
- 64, 65, 66, 67, 68, 69, 70, 71, 72, 73, 74, 75,\
- 76, 77, 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,\
- 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98, 99,\
- 100, 101, 102, 103, 104, 105},\
- .oobfree = {\
- {.offset = 106,\
- .length = 8 } } \
-}
-#endif /* __ASM_ARCH_OMAP_GPMC_H */
diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h b/arch/arm/include/asm/arch-am33xx/sys_proto.h
index 2e5c356..91ff2ad 100644
--- a/arch/arm/include/asm/arch-am33xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h
@@ -10,6 +10,7 @@
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
+#include <linux/mtd/omap_gpmc.h>
#include <asm/arch/cpu.h>
#define BOARD_REV_ID 0x0
diff --git a/arch/arm/include/asm/arch-omap3/cpu.h b/arch/arm/include/asm/arch-omap3/cpu.h
index 61ec8f2..4d06ef8 100644
--- a/arch/arm/include/asm/arch-omap3/cpu.h
+++ b/arch/arm/include/asm/arch-omap3/cpu.h
@@ -77,59 +77,7 @@ struct ctrl_id {
#define GPMC_CONFIG_CS0_BASE (GPMC_BASE + GPMC_CONFIG_CS0)
#ifndef __KERNEL_STRICT_NAMES
-#ifndef __ASSEMBLY__
-struct gpmc_cs {
- u32 config1; /* 0x00 */
- u32 config2; /* 0x04 */
- u32 config3; /* 0x08 */
- u32 config4; /* 0x0C */
- u32 config5; /* 0x10 */
- u32 config6; /* 0x14 */
- u32 config7; /* 0x18 */
- u32 nand_cmd; /* 0x1C */
- u32 nand_adr; /* 0x20 */
- u32 nand_dat; /* 0x24 */
- u8 res[8]; /* blow up to 0x30 byte */
-};
-
-struct bch_res_0_3 {
- u32 bch_result_x[4];
-};
-
-struct gpmc {
- u8 res1[0x10];
- u32 sysconfig; /* 0x10 */
- u8 res2[0x4];
- u32 irqstatus; /* 0x18 */
- u32 irqenable; /* 0x1C */
- u8 res3[0x20];
- u32 timeout_control; /* 0x40 */
- u8 res4[0xC];
- u32 config; /* 0x50 */
- u32 status; /* 0x54 */
- u8 res5[0x8]; /* 0x58 */
- struct gpmc_cs cs[8]; /* 0x60, 0x90, .. */
- u8 res6[0x14]; /* 0x1E0 */
- u32 ecc_config; /* 0x1F4 */
- u32 ecc_control; /* 0x1F8 */
- u32 ecc_size_config; /* 0x1FC */
- u32 ecc1_result; /* 0x200 */
- u32 ecc2_result; /* 0x204 */
- u32 ecc3_result; /* 0x208 */
- u32 ecc4_result; /* 0x20C */
- u32 ecc5_result; /* 0x210 */
- u32 ecc6_result; /* 0x214 */
- u32 ecc7_result; /* 0x218 */
- u32 ecc8_result; /* 0x21C */
- u32 ecc9_result; /* 0x220 */
- u8 res7[0x1C]; /* fill up to 0x240 */
- struct bch_res_0_3 bch_result_0_3[7]; /* 0x240 */
-};
-
-/* Used for board specific gpmc initialization */
-extern struct gpmc *gpmc_cfg;
-
-#else /* __ASSEMBLY__ */
+#ifdef __ASSEMBLY__
#define GPMC_CONFIG1 0x00
#define GPMC_CONFIG2 0x04
#define GPMC_CONFIG3 0x08
diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
index bcc22c4..1804191 100644
--- a/arch/arm/include/asm/arch-omap3/mem.h
+++ b/arch/arm/include/asm/arch-omap3/mem.h
@@ -419,6 +419,16 @@ enum {
#define NET_GPMC_CONFIG6 0x00000FCF
#define NET_GPMC_CONFIG7 0x00000f6c
+/* GPMC CS configuration for an SMSC LAN9221 ethernet controller */
+#define NET_LAN9221_GPMC_CONFIG1 0x00001000
+#define NET_LAN9221_GPMC_CONFIG2 0x00060700
+#define NET_LAN9221_GPMC_CONFIG3 0x00020201
+#define NET_LAN9221_GPMC_CONFIG4 0x06000700
+#define NET_LAN9221_GPMC_CONFIG5 0x0006090A
+#define NET_LAN9221_GPMC_CONFIG6 0x87030000
+#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c
+
+
/* max number of GPMC Chip Selects */
#define GPMC_MAX_CS 8
/* max number of GPMC regs */
diff --git a/arch/arm/include/asm/arch-omap3/omap_gpmc.h b/arch/arm/include/asm/arch-omap3/omap_gpmc.h
deleted file mode 100644
index bf23219..0000000
--- a/arch/arm/include/asm/arch-omap3/omap_gpmc.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
- * Rohit Choraria <rohitkc@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __ASM_ARCH_OMAP_GPMC_H
-#define __ASM_ARCH_OMAP_GPMC_H
-
-/*
- * These GPMC_NAND_HW_BCHx_ECC_LAYOUT defines using the BCH library.
- * The OOB layout was first defined by linx kernel in commit
- * 0e618ef0a6a33cf7ef96c2c824402088dd8ef48c, we have to reuse it here cause
- * we want to be compatible.
- */
-#define GPMC_NAND_HW_BCH8_ECC_LAYOUT {\
- .eccbytes = 56,\
- .eccpos = {12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22,\
- 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36,\
- 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50,\
- 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63},\
- .oobfree = {\
- {.offset = 2,\
- .length = 10 } } \
-}
-
-/* GPMC CS configuration for an SMSC LAN9221 ethernet controller */
-#define NET_LAN9221_GPMC_CONFIG1 0x00001000
-#define NET_LAN9221_GPMC_CONFIG2 0x00060700
-#define NET_LAN9221_GPMC_CONFIG3 0x00020201
-#define NET_LAN9221_GPMC_CONFIG4 0x06000700
-#define NET_LAN9221_GPMC_CONFIG5 0x0006090A
-#define NET_LAN9221_GPMC_CONFIG6 0x87030000
-#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c
-
-#endif /* __ASM_ARCH_OMAP_GPMC_H */
diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
index 43b54f7..44fa66f 100644
--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
@@ -7,6 +7,7 @@
*/
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
+#include <linux/mtd/omap_gpmc.h>
typedef struct {
u32 mtype;
diff --git a/arch/arm/include/asm/arch-omap4/cpu.h b/arch/arm/include/asm/arch-omap4/cpu.h
index 545d9d9..c21fb54 100644
--- a/arch/arm/include/asm/arch-omap4/cpu.h
+++ b/arch/arm/include/asm/arch-omap4/cpu.h
@@ -14,51 +14,6 @@
#ifndef __KERNEL_STRICT_NAMES
#ifndef __ASSEMBLY__
-struct gpmc_cs {
- u32 config1; /* 0x00 */
- u32 config2; /* 0x04 */
- u32 config3; /* 0x08 */
- u32 config4; /* 0x0C */
- u32 config5; /* 0x10 */
- u32 config6; /* 0x14 */
- u32 config7; /* 0x18 */
- u32 nand_cmd; /* 0x1C */
- u32 nand_adr; /* 0x20 */
- u32 nand_dat; /* 0x24 */
- u8 res[8]; /* blow up to 0x30 byte */
-};
-
-struct gpmc {
- u8 res1[0x10];
- u32 sysconfig; /* 0x10 */
- u8 res2[0x4];
- u32 irqstatus; /* 0x18 */
- u32 irqenable; /* 0x1C */
- u8 res3[0x20];
- u32 timeout_control; /* 0x40 */
- u8 res4[0xC];
- u32 config; /* 0x50 */
- u32 status; /* 0x54 */
- u8 res5[0x8]; /* 0x58 */
- struct gpmc_cs cs[8]; /* 0x60, 0x90, .. */
- u8 res6[0x14]; /* 0x1E0 */
- u32 ecc_config; /* 0x1F4 */
- u32 ecc_control; /* 0x1F8 */
- u32 ecc_size_config; /* 0x1FC */
- u32 ecc1_result; /* 0x200 */
- u32 ecc2_result; /* 0x204 */
- u32 ecc3_result; /* 0x208 */
- u32 ecc4_result; /* 0x20C */
- u32 ecc5_result; /* 0x210 */
- u32 ecc6_result; /* 0x214 */
- u32 ecc7_result; /* 0x218 */
- u32 ecc8_result; /* 0x21C */
- u32 ecc9_result; /* 0x220 */
-};
-
-/* Used for board specific gpmc initialization */
-extern struct gpmc *gpmc_cfg;
-
struct gptimer {
u32 tidr; /* 0x00 r */
u8 res[0xc];
diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h
index fc94725..b338a15 100644
--- a/arch/arm/include/asm/arch-omap4/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap4/sys_proto.h
@@ -12,6 +12,7 @@
#include <asm/arch/clock.h>
#include <asm/io.h>
#include <asm/omap_common.h>
+#include <linux/mtd/omap_gpmc.h>
#include <asm/arch/mux_omap4.h>
DECLARE_GLOBAL_DATA_PTR;
diff --git a/arch/arm/include/asm/arch-omap5/cpu.h b/arch/arm/include/asm/arch-omap5/cpu.h
index fb5a568..5f1d745 100644
--- a/arch/arm/include/asm/arch-omap5/cpu.h
+++ b/arch/arm/include/asm/arch-omap5/cpu.h
@@ -16,51 +16,6 @@
#ifndef __KERNEL_STRICT_NAMES
#ifndef __ASSEMBLY__
-struct gpmc_cs {
- u32 config1; /* 0x00 */
- u32 config2; /* 0x04 */
- u32 config3; /* 0x08 */
- u32 config4; /* 0x0C */
- u32 config5; /* 0x10 */
- u32 config6; /* 0x14 */
- u32 config7; /* 0x18 */
- u32 nand_cmd; /* 0x1C */
- u32 nand_adr; /* 0x20 */
- u32 nand_dat; /* 0x24 */
- u8 res[8]; /* blow up to 0x30 byte */
-};
-
-struct gpmc {
- u8 res1[0x10];
- u32 sysconfig; /* 0x10 */
- u8 res2[0x4];
- u32 irqstatus; /* 0x18 */
- u32 irqenable; /* 0x1C */
- u8 res3[0x20];
- u32 timeout_control; /* 0x40 */
- u8 res4[0xC];
- u32 config; /* 0x50 */
- u32 status; /* 0x54 */
- u8 res5[0x8]; /* 0x58 */
- struct gpmc_cs cs[8]; /* 0x60, 0x90, .. */
- u8 res6[0x14]; /* 0x1E0 */
- u32 ecc_config; /* 0x1F4 */
- u32 ecc_control; /* 0x1F8 */
- u32 ecc_size_config; /* 0x1FC */
- u32 ecc1_result; /* 0x200 */
- u32 ecc2_result; /* 0x204 */
- u32 ecc3_result; /* 0x208 */
- u32 ecc4_result; /* 0x20C */
- u32 ecc5_result; /* 0x210 */
- u32 ecc6_result; /* 0x214 */
- u32 ecc7_result; /* 0x218 */
- u32 ecc8_result; /* 0x21C */
- u32 ecc9_result; /* 0x220 */
-};
-
-/* Used for board specific gpmc initialization */
-extern struct gpmc *gpmc_cfg;
-
struct gptimer {
u32 tidr; /* 0x00 r */
u8 res1[0xc];
diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h
index 43011a4..9e007c8 100644
--- a/arch/arm/include/asm/arch-omap5/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap5/sys_proto.h
@@ -12,6 +12,7 @@
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/omap_common.h>
+#include <linux/mtd/omap_gpmc.h>
#include <asm/arch/clock.h>
DECLARE_GLOBAL_DATA_PTR;
diff --git a/arch/arm/include/asm/omap_gpmc.h b/arch/arm/include/asm/omap_gpmc.h
deleted file mode 100644
index d4143ec..0000000
--- a/arch/arm/include/asm/omap_gpmc.h
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
- * Rohit Choraria <rohitkc@ti.com>
- *
- * (C) Copyright 2013 Andreas Bießmann <andreas.devel@googlemail.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __ASM_OMAP_GPMC_H
-#define __ASM_OMAP_GPMC_H
-
-#include <asm/arch/omap_gpmc.h>
-
-#define GPMC_BUF_EMPTY 0
-#define GPMC_BUF_FULL 1
-
-#define ECCCLEAR (0x1 << 8)
-#define ECCRESULTREG1 (0x1 << 0)
-#define ECCSIZE512BYTE 0xFF
-#define ECCSIZE1 (ECCSIZE512BYTE << 22)
-#define ECCSIZE0 (ECCSIZE512BYTE << 12)
-#define ECCSIZE0SEL (0x000 << 0)
-
-/* Generic ECC Layouts */
-/* Large Page x8 NAND device Layout */
-#ifdef GPMC_NAND_ECC_LP_x8_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 12,\
- .eccpos = {1, 2, 3, 4, 5, 6, 7, 8,\
- 9, 10, 11, 12},\
- .oobfree = {\
- {.offset = 13,\
- .length = 51 } } \
-}
-#endif
-
-/* Large Page x16 NAND device Layout */
-#ifdef GPMC_NAND_ECC_LP_x16_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 12,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9,\
- 10, 11, 12, 13},\
- .oobfree = {\
- {.offset = 14,\
- .length = 50 } } \
-}
-#endif
-
-/* Small Page x8 NAND device Layout */
-#ifdef GPMC_NAND_ECC_SP_x8_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 3,\
- .eccpos = {1, 2, 3},\
- .oobfree = {\
- {.offset = 4,\
- .length = 12 } } \
-}
-#endif
-
-/* Small Page x16 NAND device Layout */
-#ifdef GPMC_NAND_ECC_SP_x16_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 3,\
- .eccpos = {2, 3, 4},\
- .oobfree = {\
- {.offset = 5,\
- .length = 11 } } \
-}
-#endif
-
-enum omap_ecc {
- /* 1-bit ECC calculation by Software, Error detection by Software */
- OMAP_ECC_HAM1_CODE_SW = 1, /* avoid un-initialized int can be 0x0 */
- /* 1-bit ECC calculation by GPMC, Error detection by Software */
- /* ECC layout compatible to legacy ROMCODE. */
- OMAP_ECC_HAM1_CODE_HW,
- /* 4-bit ECC calculation by GPMC, Error detection by Software */
- OMAP_ECC_BCH4_CODE_HW_DETECTION_SW,
- /* 4-bit ECC calculation by GPMC, Error detection by ELM */
- OMAP_ECC_BCH4_CODE_HW,
- /* 8-bit ECC calculation by GPMC, Error detection by Software */
- OMAP_ECC_BCH8_CODE_HW_DETECTION_SW,
- /* 8-bit ECC calculation by GPMC, Error detection by ELM */
- OMAP_ECC_BCH8_CODE_HW,
-};
-
-#endif /* __ASM_OMAP_GPMC_H */
diff --git a/board/isee/igep00x0/igep00x0.c b/board/isee/igep00x0/igep00x0.c
index 7a7500b..3b2b1f1 100644
--- a/board/isee/igep00x0/igep00x0.c
+++ b/board/isee/igep00x0/igep00x0.c
@@ -8,7 +8,6 @@
#include <twl4030.h>
#include <netdev.h>
#include <asm/gpio.h>
-#include <asm/omap_gpmc.h>
#include <asm/io.h>
#include <asm/arch/mem.h>
#include <asm/arch/mmc_host_def.h>
diff --git a/board/overo/overo.c b/board/overo/overo.c
index 9ac35d2..1192d02 100644
--- a/board/overo/overo.c
+++ b/board/overo/overo.c
@@ -21,7 +21,6 @@
#include <asm/arch/mux.h>
#include <asm/arch/mem.h>
#include <asm/arch/sys_proto.h>
-#include <asm/omap_gpmc.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
#include "overo.h"
diff --git a/board/ti/am335x/README b/board/ti/am335x/README
index 2a30ab8..947305b 100644
--- a/board/ti/am335x/README
+++ b/board/ti/am335x/README
@@ -46,23 +46,42 @@ NAND
The AM335x GP EVM ships with a 256MiB NAND available in most profiles. In
this example to program the NAND we assume that an SD card has been
inserted with the files to write in the first SD slot and that mtdparts
-have been configured correctly for the board. As a time saving measure we
-load MLO into memory in one location, copy it into the three locatations
-that the ROM checks for additional valid copies, then load U-Boot into
-memory. We then write that whole section of memory to NAND.
-
-U-Boot # mmc rescan
-U-Boot # env default -f -a
-U-Boot # nand erase.chip
-U-Boot # saveenv
-U-Boot # load mmc 0 81000000 MLO
-U-Boot # cp.b 81000000 81020000 20000
-U-Boot # cp.b 81000000 81040000 20000
-U-Boot # cp.b 81000000 81060000 20000
-U-Boot # load mmc 0 81080000 u-boot.img
-U-Boot # nand write 81000000 0 260000
-U-Boot # load mmc 0 ${loadaddr} uImage
-U-Boot # nand write ${loadaddr} kernel 500000
+have been configured correctly for the board. All images are first loaded
+into memory, then written to NAND.
+
+Step-1: Building u-boot for NAND boot
+ Set following CONFIGxx options for NAND device.
+ CONFIG_SYS_NAND_PAGE_SIZE number of main bytes in NAND page
+ CONFIG_SYS_NAND_OOBSIZE number of OOB bytes in NAND page
+ CONFIG_SYS_NAND_BLOCK_SIZE number of bytes in NAND erase-block
+ CONFIG_SYS_NAND_ECCPOS ECC map for NAND page
+ CONFIG_NAND_OMAP_ECCSCHEME (refer doc/README.nand)
+
+Step-2: Flashing NAND via MMC/SD
+ # select BOOTSEL to MMC/SD boot and boot from MMC/SD card
+ U-Boot # mmc rescan
+ # erase flash
+ U-Boot # nand erase.chip
+ U-Boot # env default -f -a
+ U-Boot # saveenv
+ # flash MLO. Redundant copies of MLO are kept for failsafe
+ U-Boot # load mmc 0 0x82000000 MLO
+ U-Boot # nand write 0x82000000 0x00000 0x20000
+ U-Boot # nand write 0x82000000 0x20000 0x20000
+ U-Boot # nand write 0x82000000 0x40000 0x20000
+ U-Boot # nand write 0x82000000 0x60000 0x20000
+ # flash u-boot.img
+ U-Boot # load mmc 0 0x82000000 u-boot.img
+ U-Boot # nand write 0x82000000 0x80000 0x60000
+ # flash kernel image
+ U-Boot # load mmc 0 0x82000000 uImage
+ U-Boot # nand write 0x82000000 ${nandsrcaddr} ${nandimgsize}
+ # flash filesystem image
+ U-Boot # load mmc 0 0x82000000 filesystem.img
+ U-Boot # nand write 0x82000000 ${loadaddress} 0x300000
+
+Step-3: Set BOOTSEL pin to select NAND boot, and POR the device.
+ The device should boot from images flashed on NAND device.
NOR
===
diff --git a/drivers/mtd/nand/omap_elm.c b/drivers/mtd/nand/omap_elm.c
index 2aa7807..47b1f1b 100644
--- a/drivers/mtd/nand/omap_elm.c
+++ b/drivers/mtd/nand/omap_elm.c
@@ -16,9 +16,9 @@
#include <common.h>
#include <asm/io.h>
#include <asm/errno.h>
-#include <asm/arch/cpu.h>
-#include <asm/omap_gpmc.h>
-#include <asm/omap_elm.h>
+#include <linux/mtd/omap_gpmc.h>
+#include <linux/mtd/omap_elm.h>
+#include <asm/arch/hardware.h>
#define ELM_DEFAULT_POLY (0)
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index 389c4de..881a636 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -9,17 +9,24 @@
#include <asm/io.h>
#include <asm/errno.h>
#include <asm/arch/mem.h>
-#include <asm/arch/cpu.h>
-#include <asm/omap_gpmc.h>
+#include <linux/mtd/omap_gpmc.h>
#include <linux/mtd/nand_ecc.h>
#include <linux/bch.h>
#include <linux/compiler.h>
#include <nand.h>
-#include <asm/omap_elm.h>
+#include <linux/mtd/omap_elm.h>
#define BADBLOCK_MARKER_LENGTH 2
#define SECTOR_BYTES 512
+#define ECCCLEAR (0x1 << 8)
+#define ECCRESULTREG1 (0x1 << 0)
+/* 4 bit padding to make byte aligned, 56 = 52 + 4 */
+#define BCH4_BIT_PAD 4
+#ifdef CONFIG_BCH
+static u8 bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2,
+ 0x97, 0x79, 0xe5, 0x24, 0xb5};
+#endif
static uint8_t cs;
static __maybe_unused struct nand_ecclayout omap_ecclayout;
@@ -60,21 +67,6 @@ int omap_spl_dev_ready(struct mtd_info *mtd)
}
#endif
-/*
- * omap_hwecc_init - Initialize the Hardware ECC for NAND flash in
- * GPMC controller
- * @mtd: MTD device structure
- *
- */
-static void __maybe_unused omap_hwecc_init(struct nand_chip *chip)
-{
- /*
- * Init ECC Control Register
- * Clear all ECC | Enable Reg1
- */
- writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
- writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL, &gpmc_cfg->ecc_size_config);
-}
/*
* gen_true_ecc - This function will generate true ECC value, which
@@ -156,74 +148,6 @@ static int __maybe_unused omap_correct_data(struct mtd_info *mtd, uint8_t *dat,
}
/*
- * omap_calculate_ecc - Generate non-inverted ECC bytes.
- *
- * Using noninverted ECC can be considered ugly since writing a blank
- * page ie. padding will clear the ECC bytes. This is no problem as
- * long nobody is trying to write data on the seemingly unused page.
- * Reading an erased page will produce an ECC mismatch between
- * generated and read ECC bytes that has to be dealt with separately.
- * E.g. if page is 0xFF (fresh erased), and if HW ECC engine within GPMC
- * is used, the result of read will be 0x0 while the ECC offsets of the
- * spare area will be 0xFF which will result in an ECC mismatch.
- * @mtd: MTD structure
- * @dat: unused
- * @ecc_code: ecc_code buffer
- */
-static int __maybe_unused omap_calculate_ecc(struct mtd_info *mtd,
- const uint8_t *dat, uint8_t *ecc_code)
-{
- u_int32_t val;
-
- /* Start Reading from HW ECC1_Result = 0x200 */
- val = readl(&gpmc_cfg->ecc1_result);
-
- ecc_code[0] = val & 0xFF;
- ecc_code[1] = (val >> 16) & 0xFF;
- ecc_code[2] = ((val >> 8) & 0x0F) | ((val >> 20) & 0xF0);
-
- /*
- * Stop reading anymore ECC vals and clear old results
- * enable will be called if more reads are required
- */
- writel(0x000, &gpmc_cfg->ecc_config);
-
- return 0;
-}
-
-/*
- * omap_enable_ecc - This function enables the hardware ecc functionality
- * @mtd: MTD device structure
- * @mode: Read/Write mode
- */
-static void __maybe_unused omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
-{
- struct nand_chip *chip = mtd->priv;
- uint32_t val, dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1;
-
- switch (mode) {
- case NAND_ECC_READ:
- case NAND_ECC_WRITE:
- /* Clear the ecc result registers, select ecc reg as 1 */
- writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
-
- /*
- * Size 0 = 0xFF, Size1 is 0xFF - both are 512 bytes
- * tell all regs to generate size0 sized regs
- * we just have a single ECC engine for all CS
- */
- writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL,
- &gpmc_cfg->ecc_size_config);
- val = (dev_width << 7) | (cs << 1) | (0x1);
- writel(val, &gpmc_cfg->ecc_config);
- break;
- default:
- printf("Error: Unrecognized Mode[%d]!\n", mode);
- break;
- }
-}
-
-/*
* Generic BCH interface
*/
struct nand_bch_priv {
@@ -239,12 +163,7 @@ struct nand_bch_priv {
#define ECC_BCH8 1
#define ECC_BCH16 2
-/* GPMC ecc engine settings */
-#define BCH_WRAPMODE_1 1 /* BCH wrap mode 1 */
-#define BCH_WRAPMODE_6 6 /* BCH wrap mode 6 */
-
/* BCH nibbles for diff bch levels */
-#define NAND_ECC_HW_BCH ((uint8_t)(NAND_ECC_HW_OOB_FIRST) + 1)
#define ECC_BCH4_NIBBLES 13
#define ECC_BCH8_NIBBLES 26
#define ECC_BCH16_NIBBLES 52
@@ -256,266 +175,161 @@ struct nand_bch_priv {
* When some users with other BCH strength will exists this have to change!
*/
static __maybe_unused struct nand_bch_priv bch_priv = {
- .mode = NAND_ECC_HW_BCH,
.type = ECC_BCH8,
.nibbles = ECC_BCH8_NIBBLES,
.control = NULL
};
/*
- * omap_hwecc_init_bch - Initialize the BCH Hardware ECC for NAND flash in
- * GPMC controller
- * @mtd: MTD device structure
- * @mode: Read/Write mode
- */
-__maybe_unused
-static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode)
+ * omap_reverse_list - re-orders list elements in reverse order [internal]
+ * @list: pointer to start of list
+ * @length: length of list
+*/
+void omap_reverse_list(u8 *list, unsigned int length)
{
- uint32_t val;
- uint32_t dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1;
- uint32_t unused_length = 0;
- uint32_t wr_mode = BCH_WRAPMODE_6;
- struct nand_bch_priv *bch = chip->priv;
-
- /* Clear the ecc result registers, select ecc reg as 1 */
- writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
-
- if (bch->ecc_scheme == OMAP_ECC_BCH8_CODE_HW) {
- wr_mode = BCH_WRAPMODE_1;
-
- switch (bch->nibbles) {
- case ECC_BCH4_NIBBLES:
- unused_length = 3;
- break;
- case ECC_BCH8_NIBBLES:
- unused_length = 2;
- break;
- case ECC_BCH16_NIBBLES:
- unused_length = 0;
- break;
- }
-
- /*
- * This is ecc_size_config for ELM mode. Here we are using
- * different settings for read and write access and also
- * depending on BCH strength.
- */
- switch (mode) {
- case NAND_ECC_WRITE:
- /* write access only setup eccsize1 config */
- val = ((unused_length + bch->nibbles) << 22);
- break;
-
- case NAND_ECC_READ:
- default:
- /*
- * by default eccsize0 selected for ecc1resultsize
- * eccsize0 config.
- */
- val = (bch->nibbles << 12);
- /* eccsize1 config */
- val |= (unused_length << 22);
- break;
- }
- } else {
- /*
- * This ecc_size_config setting is for BCH sw library.
- *
- * Note: we only support BCH8 currently with BCH sw library!
- * Should be really easy to adobt to BCH4, however some omap3
- * have flaws with BCH4.
- *
- * Here we are using wrapping mode 6 both for reading and
- * writing, with:
- * size0 = 0 (no additional protected byte in spare area)
- * size1 = 32 (skip 32 nibbles = 16 bytes per sector in
- * spare area)
- */
- val = (32 << 22) | (0 << 12);
+ unsigned int i, j;
+ unsigned int half_length = length / 2;
+ u8 tmp;
+ for (i = 0, j = length - 1; i < half_length; i++, j--) {
+ tmp = list[i];
+ list[i] = list[j];
+ list[j] = tmp;
}
- /* ecc size configuration */
- writel(val, &gpmc_cfg->ecc_size_config);
-
- /*
- * Configure the ecc engine in gpmc
- * We assume 512 Byte sector pages for access to NAND.
- */
- val = (1 << 16); /* enable BCH mode */
- val |= (bch->type << 12); /* setup BCH type */
- val |= (wr_mode << 8); /* setup wrapping mode */
- val |= (dev_width << 7); /* setup device width (16 or 8 bit) */
- val |= (cs << 1); /* setup chip select to work on */
- debug("set ECC_CONFIG=0x%08x\n", val);
- writel(val, &gpmc_cfg->ecc_config);
}
/*
- * omap_enable_ecc_bch - This function enables the bch h/w ecc functionality
+ * omap_enable_hwecc - configures GPMC as per ECC scheme before read/write
* @mtd: MTD device structure
* @mode: Read/Write mode
*/
__maybe_unused
-static void omap_enable_ecc_bch(struct mtd_info *mtd, int32_t mode)
-{
- struct nand_chip *chip = mtd->priv;
-
- omap_hwecc_init_bch(chip, mode);
- /* enable ecc */
- writel((readl(&gpmc_cfg->ecc_config) | 0x1), &gpmc_cfg->ecc_config);
-}
-
-/*
- * omap_ecc_disable - Disable H/W ECC calculation
- *
- * @mtd: MTD device structure
- */
-static void __maybe_unused omap_ecc_disable(struct mtd_info *mtd)
+static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
{
- writel((readl(&gpmc_cfg->ecc_config) & ~0x1), &gpmc_cfg->ecc_config);
+ struct nand_chip *nand = mtd->priv;
+ struct nand_bch_priv *bch = nand->priv;
+ unsigned int dev_width = (nand->options & NAND_BUSWIDTH_16) ? 1 : 0;
+ unsigned int ecc_algo = 0;
+ unsigned int bch_type = 0;
+ unsigned int eccsize1 = 0x00, eccsize0 = 0x00, bch_wrapmode = 0x00;
+ u32 ecc_size_config_val = 0;
+ u32 ecc_config_val = 0;
+
+ /* configure GPMC for specific ecc-scheme */
+ switch (bch->ecc_scheme) {
+ case OMAP_ECC_HAM1_CODE_SW:
+ return;
+ case OMAP_ECC_HAM1_CODE_HW:
+ ecc_algo = 0x0;
+ bch_type = 0x0;
+ bch_wrapmode = 0x00;
+ eccsize0 = 0xFF;
+ eccsize1 = 0xFF;
+ break;
+ case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
+ case OMAP_ECC_BCH8_CODE_HW:
+ ecc_algo = 0x1;
+ bch_type = 0x1;
+ if (mode == NAND_ECC_WRITE) {
+ bch_wrapmode = 0x01;
+ eccsize0 = 0; /* extra bits in nibbles per sector */
+ eccsize1 = 28; /* OOB bits in nibbles per sector */
+ } else {
+ bch_wrapmode = 0x01;
+ eccsize0 = 26; /* ECC bits in nibbles per sector */
+ eccsize1 = 2; /* non-ECC bits in nibbles per sector */
+ }
+ break;
+ default:
+ return;
+ }
+ /* Clear ecc and enable bits */
+ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
+ /* Configure ecc size for BCH */
+ ecc_size_config_val = (eccsize1 << 22) | (eccsize0 << 12);
+ writel(ecc_size_config_val, &gpmc_cfg->ecc_size_config);
+
+ /* Configure device details for BCH engine */
+ ecc_config_val = ((ecc_algo << 16) | /* HAM1 | BCHx */
+ (bch_type << 12) | /* BCH4/BCH8/BCH16 */
+ (bch_wrapmode << 8) | /* wrap mode */
+ (dev_width << 7) | /* bus width */
+ (0x0 << 4) | /* number of sectors */
+ (cs << 1) | /* ECC CS */
+ (0x1)); /* enable ECC */
+ writel(ecc_config_val, &gpmc_cfg->ecc_config);
}
/*
- * BCH support using ELM module
- */
-#ifdef CONFIG_NAND_OMAP_ELM
-/*
- * omap_read_bch8_result - Read BCH result for BCH8 level
- *
- * @mtd: MTD device structure
- * @big_endian: When set read register 3 first
- * @ecc_code: Read syndrome from BCH result registers
+ * omap_calculate_ecc - Read ECC result
+ * @mtd: MTD structure
+ * @dat: unused
+ * @ecc_code: ecc_code buffer
+ * Using noninverted ECC can be considered ugly since writing a blank
+ * page ie. padding will clear the ECC bytes. This is no problem as
+ * long nobody is trying to write data on the seemingly unused page.
+ * Reading an erased page will produce an ECC mismatch between
+ * generated and read ECC bytes that has to be dealt with separately.
+ * E.g. if page is 0xFF (fresh erased), and if HW ECC engine within GPMC
+ * is used, the result of read will be 0x0 while the ECC offsets of the
+ * spare area will be 0xFF which will result in an ECC mismatch.
*/
-static void omap_read_bch8_result(struct mtd_info *mtd, uint8_t big_endian,
+static int omap_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat,
uint8_t *ecc_code)
{
- uint32_t *ptr;
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint32_t *ptr, val = 0;
int8_t i = 0, j;
- if (big_endian) {
+ switch (bch->ecc_scheme) {
+ case OMAP_ECC_HAM1_CODE_HW:
+ val = readl(&gpmc_cfg->ecc1_result);
+ ecc_code[0] = val & 0xFF;
+ ecc_code[1] = (val >> 16) & 0xFF;
+ ecc_code[2] = ((val >> 8) & 0x0F) | ((val >> 20) & 0xF0);
+ break;
+#ifdef CONFIG_BCH
+ case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
+#endif
+ case OMAP_ECC_BCH8_CODE_HW:
ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[3];
- ecc_code[i++] = readl(ptr) & 0xFF;
+ val = readl(ptr);
+ ecc_code[i++] = (val >> 0) & 0xFF;
ptr--;
for (j = 0; j < 3; j++) {
- ecc_code[i++] = (readl(ptr) >> 24) & 0xFF;
- ecc_code[i++] = (readl(ptr) >> 16) & 0xFF;
- ecc_code[i++] = (readl(ptr) >> 8) & 0xFF;
- ecc_code[i++] = readl(ptr) & 0xFF;
+ val = readl(ptr);
+ ecc_code[i++] = (val >> 24) & 0xFF;
+ ecc_code[i++] = (val >> 16) & 0xFF;
+ ecc_code[i++] = (val >> 8) & 0xFF;
+ ecc_code[i++] = (val >> 0) & 0xFF;
ptr--;
}
- } else {
- ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[0];
- for (j = 0; j < 3; j++) {
- ecc_code[i++] = readl(ptr) & 0xFF;
- ecc_code[i++] = (readl(ptr) >> 8) & 0xFF;
- ecc_code[i++] = (readl(ptr) >> 16) & 0xFF;
- ecc_code[i++] = (readl(ptr) >> 24) & 0xFF;
- ptr++;
- }
- ecc_code[i++] = readl(ptr) & 0xFF;
- ecc_code[i++] = 0; /* 14th byte is always zero */
+ break;
+ default:
+ return -EINVAL;
}
-}
-
-/*
- * omap_rotate_ecc_bch - Rotate the syndrome bytes
- *
- * @mtd: MTD device structure
- * @calc_ecc: ECC read from ECC registers
- * @syndrome: Rotated syndrome will be retuned in this array
- *
- */
-static void omap_rotate_ecc_bch(struct mtd_info *mtd, uint8_t *calc_ecc,
- uint8_t *syndrome)
-{
- struct nand_chip *chip = mtd->priv;
- struct nand_bch_priv *bch = chip->priv;
- uint8_t n_bytes = 0;
- int8_t i, j;
-
- switch (bch->type) {
- case ECC_BCH4:
- n_bytes = 8;
+ /* ECC scheme specific syndrome customizations */
+ switch (bch->ecc_scheme) {
+ case OMAP_ECC_HAM1_CODE_HW:
break;
+#ifdef CONFIG_BCH
+ case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
- case ECC_BCH16:
- n_bytes = 28;
+ for (i = 0; i < chip->ecc.bytes; i++)
+ *(ecc_code + i) = *(ecc_code + i) ^
+ bch8_polynomial[i];
break;
-
- case ECC_BCH8:
- default:
- n_bytes = 13;
+#endif
+ case OMAP_ECC_BCH8_CODE_HW:
+ ecc_code[chip->ecc.bytes - 1] = 0x00;
break;
+ default:
+ return -EINVAL;
}
-
- for (i = 0, j = (n_bytes-1); i < n_bytes; i++, j--)
- syndrome[i] = calc_ecc[j];
-}
-
-/*
- * omap_calculate_ecc_bch - Read BCH ECC result
- *
- * @mtd: MTD structure
- * @dat: unused
- * @ecc_code: ecc_code buffer
- */
-static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat,
- uint8_t *ecc_code)
-{
- struct nand_chip *chip = mtd->priv;
- struct nand_bch_priv *bch = chip->priv;
- uint8_t big_endian = 1;
- int8_t ret = 0;
-
- if (bch->type == ECC_BCH8)
- omap_read_bch8_result(mtd, big_endian, ecc_code);
- else /* BCH4 and BCH16 currently not supported */
- ret = -1;
-
- /*
- * Stop reading anymore ECC vals and clear old results
- * enable will be called if more reads are required
- */
- omap_ecc_disable(mtd);
-
- return ret;
-}
-
-/*
- * omap_fix_errors_bch - Correct bch error in the data
- *
- * @mtd: MTD device structure
- * @data: Data read from flash
- * @error_count:Number of errors in data
- * @error_loc: Locations of errors in the data
- *
- */
-static void omap_fix_errors_bch(struct mtd_info *mtd, uint8_t *data,
- uint32_t error_count, uint32_t *error_loc)
-{
- struct nand_chip *chip = mtd->priv;
- struct nand_bch_priv *bch = chip->priv;
- uint8_t count = 0;
- uint32_t error_byte_pos;
- uint32_t error_bit_mask;
- uint32_t last_bit = (bch->nibbles * 4) - 1;
-
- /* Flip all bits as specified by the error location array. */
- /* FOR( each found error location flip the bit ) */
- for (count = 0; count < error_count; count++) {
- if (error_loc[count] > last_bit) {
- /* Remove the ECC spare bits from correction. */
- error_loc[count] -= (last_bit + 1);
- /* Offset bit in data region */
- error_byte_pos = ((512 * 8) -
- (error_loc[count]) - 1) / 8;
- /* Error Bit mask */
- error_bit_mask = 0x1 << (error_loc[count] % 8);
- /* Toggle the error bit to make the correction. */
- data[error_byte_pos] ^= error_bit_mask;
- }
- }
+ return 0;
}
+#ifdef CONFIG_NAND_OMAP_ELM
/*
* omap_correct_data_bch - Compares the ecc read from nand spare area
* with ECC registers values and corrects one bit error if it has occured
@@ -532,40 +346,72 @@ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
{
struct nand_chip *chip = mtd->priv;
struct nand_bch_priv *bch = chip->priv;
- uint8_t syndrome[28];
- uint32_t error_count = 0;
+ uint32_t eccbytes = chip->ecc.bytes;
+ uint32_t error_count = 0, error_max;
uint32_t error_loc[8];
- uint32_t i, ecc_flag;
+ uint32_t i, ecc_flag = 0;
+ uint8_t count, err = 0;
+ uint32_t byte_pos, bit_pos;
+
+ /* check calculated ecc */
+ for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) {
+ if (calc_ecc[i] != 0x00)
+ ecc_flag = 1;
+ }
+ if (!ecc_flag)
+ return 0;
+ /* check for whether its a erased-page */
ecc_flag = 0;
- for (i = 0; i < chip->ecc.bytes; i++)
+ for (i = 0; i < chip->ecc.bytes && !ecc_flag; i++) {
if (read_ecc[i] != 0xff)
ecc_flag = 1;
-
+ }
if (!ecc_flag)
return 0;
- elm_reset();
- elm_config((enum bch_level)(bch->type));
-
/*
* while reading ECC result we read it in big endian.
* Hence while loading to ELM we have rotate to get the right endian.
*/
- omap_rotate_ecc_bch(mtd, calc_ecc, syndrome);
-
+ switch (bch->ecc_scheme) {
+ case OMAP_ECC_BCH8_CODE_HW:
+ omap_reverse_list(calc_ecc, eccbytes - 1);
+ break;
+ default:
+ return -EINVAL;
+ }
/* use elm module to check for errors */
- if (elm_check_error(syndrome, bch->nibbles, &error_count,
- error_loc) != 0) {
- printf("ECC: uncorrectable.\n");
- return -1;
+ elm_config((enum bch_level)(bch->type));
+ if (elm_check_error(calc_ecc, bch->nibbles, &error_count, error_loc)) {
+ printf("nand: error: uncorrectable ECC errors\n");
+ return -EINVAL;
}
-
/* correct bch error */
- if (error_count > 0)
- omap_fix_errors_bch(mtd, dat, error_count, error_loc);
-
- return 0;
+ for (count = 0; count < error_count; count++) {
+ switch (bch->type) {
+ case ECC_BCH8:
+ /* 14th byte in ECC is reserved to match ROM layout */
+ error_max = SECTOR_BYTES + (eccbytes - 1);
+ break;
+ default:
+ return -EINVAL;
+ }
+ byte_pos = error_max - (error_loc[count] / 8) - 1;
+ bit_pos = error_loc[count] % 8;
+ if (byte_pos < SECTOR_BYTES) {
+ dat[byte_pos] ^= 1 << bit_pos;
+ printf("nand: bit-flip corrected @data=%d\n", byte_pos);
+ } else if (byte_pos < error_max) {
+ read_ecc[byte_pos - SECTOR_BYTES] = 1 << bit_pos;
+ printf("nand: bit-flip corrected @oob=%d\n", byte_pos -
+ SECTOR_BYTES);
+ } else {
+ err = -EBADMSG;
+ printf("nand: error: invalid bit-flip location\n");
+ }
+ }
+ return (err) ? err : error_count;
}
/**
@@ -636,57 +482,6 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
* OMAP3 BCH8 support (with BCH library)
*/
#ifdef CONFIG_BCH
-/*
- * omap_calculate_ecc_bch_sw - Read BCH ECC result
- *
- * @mtd: MTD device structure
- * @dat: The pointer to data on which ecc is computed (unused here)
- * @ecc: The ECC output buffer
- */
-static int omap_calculate_ecc_bch_sw(struct mtd_info *mtd, const uint8_t *dat,
- uint8_t *ecc)
-{
- int ret = 0;
- size_t i;
- unsigned long nsectors, val1, val2, val3, val4;
-
- nsectors = ((readl(&gpmc_cfg->ecc_config) >> 4) & 0x7) + 1;
-
- for (i = 0; i < nsectors; i++) {
- /* Read hw-computed remainder */
- val1 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[0]);
- val2 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[1]);
- val3 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[2]);
- val4 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[3]);
-
- /*
- * Add constant polynomial to remainder, in order to get an ecc
- * sequence of 0xFFs for a buffer filled with 0xFFs.
- */
- *ecc++ = 0xef ^ (val4 & 0xFF);
- *ecc++ = 0x51 ^ ((val3 >> 24) & 0xFF);
- *ecc++ = 0x2e ^ ((val3 >> 16) & 0xFF);
- *ecc++ = 0x09 ^ ((val3 >> 8) & 0xFF);
- *ecc++ = 0xed ^ (val3 & 0xFF);
- *ecc++ = 0x93 ^ ((val2 >> 24) & 0xFF);
- *ecc++ = 0x9a ^ ((val2 >> 16) & 0xFF);
- *ecc++ = 0xc2 ^ ((val2 >> 8) & 0xFF);
- *ecc++ = 0x97 ^ (val2 & 0xFF);
- *ecc++ = 0x79 ^ ((val1 >> 24) & 0xFF);
- *ecc++ = 0xe5 ^ ((val1 >> 16) & 0xFF);
- *ecc++ = 0x24 ^ ((val1 >> 8) & 0xFF);
- *ecc++ = 0xb5 ^ (val1 & 0xFF);
- }
-
- /*
- * Stop reading anymore ECC vals and clear old results
- * enable will be called if more reads are required
- */
- omap_ecc_disable(mtd);
-
- return ret;
-}
-
/**
* omap_correct_data_bch_sw - Decode received data and correct errors
* @mtd: MTD device structure
@@ -835,9 +630,9 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
nand->ecc.strength = 8;
nand->ecc.size = SECTOR_BYTES;
nand->ecc.bytes = 13;
- nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.hwctl = omap_enable_hwecc;
nand->ecc.correct = omap_correct_data_bch_sw;
- nand->ecc.calculate = omap_calculate_ecc_bch_sw;
+ nand->ecc.calculate = omap_calculate_ecc;
/* define ecc-layout */
ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
@@ -852,7 +647,6 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
BADBLOCK_MARKER_LENGTH;
- omap_hwecc_init_bch(nand, NAND_ECC_READ);
bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW;
break;
#else
@@ -878,9 +672,9 @@ static int omap_select_ecc_scheme(struct nand_chip *nand,
nand->ecc.strength = 8;
nand->ecc.size = SECTOR_BYTES;
nand->ecc.bytes = 14;
- nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.hwctl = omap_enable_hwecc;
nand->ecc.correct = omap_correct_data_bch;
- nand->ecc.calculate = omap_calculate_ecc_bch;
+ nand->ecc.calculate = omap_calculate_ecc;
nand->ecc.read_page = omap_read_page_bch;
/* define ecc-layout */
ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 59a8f36..a5736b7 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -404,7 +404,6 @@
/* NAND support */
#ifdef CONFIG_NAND
#define CONFIG_CMD_NAND
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#if !defined(CONFIG_SPI_BOOT) && !defined(CONFIG_NOR_BOOT)
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \
diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h
index 115d1b3..c00d54f 100644
--- a/include/configs/am335x_igep0033.h
+++ b/include/configs/am335x_igep0033.h
@@ -188,7 +188,6 @@
#define CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION 1
diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
index 468fb43..4407b45 100644
--- a/include/configs/am3517_crane.h
+++ b/include/configs/am3517_crane.h
@@ -268,7 +268,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
index b8b99c8..0102ff5 100644
--- a/include/configs/am3517_evm.h
+++ b/include/configs/am3517_evm.h
@@ -277,7 +277,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index 08c67f5..cfc4f9b 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -156,8 +156,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x8_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
/* Environment information */
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 4f43ba9..16a00eb 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -116,8 +116,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
diff --git a/include/configs/dig297.h b/include/configs/dig297.h
index 5049afc..af6f56b 100644
--- a/include/configs/dig297.h
+++ b/include/configs/dig297.h
@@ -143,8 +143,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
#if defined(CONFIG_CMD_NET)
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index 7c5c2f4..47244c0 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -321,7 +321,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index c58bc91..ac0ed43 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -183,8 +183,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h
index 43616e2..7f3424b 100644
--- a/include/configs/omap3_evm_common.h
+++ b/include/configs/omap3_evm_common.h
@@ -208,7 +208,6 @@
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#elif defined(CONFIG_CMD_ONENAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index 20fbbec..12d8141 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -154,7 +154,6 @@
#ifdef CONFIG_NAND
#define PISMO1_NAND_SIZE GPMC_SIZE_128M /* Configure the PISMO */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */
diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index bedd6f9..0d03c75 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -295,7 +295,6 @@
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#endif
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index e0f0262..007e27f 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -119,8 +119,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index eacdfaa..da67787 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -131,8 +131,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 1dd53fa..f0fa96e 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -138,8 +138,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index 2863042..98b6e72 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -457,7 +457,6 @@
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* physical address */
/* to access nand at */
/* CS0 */
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index d44b5c0..3522c1a 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -186,7 +186,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index cc4001f..62f97d2 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -134,8 +134,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_BCH
diff --git a/arch/arm/include/asm/omap_elm.h b/include/linux/mtd/omap_elm.h
index 45454ea..45454ea 100644
--- a/arch/arm/include/asm/omap_elm.h
+++ b/include/linux/mtd/omap_elm.h
diff --git a/include/linux/mtd/omap_gpmc.h b/include/linux/mtd/omap_gpmc.h
new file mode 100644
index 0000000..22f6573
--- /dev/null
+++ b/include/linux/mtd/omap_gpmc.h
@@ -0,0 +1,84 @@
+/*
+ * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com>
+ * Rohit Choraria <rohitkc@ti.com>
+ *
+ * (C) Copyright 2013 Andreas Bießmann <andreas.devel@googlemail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __ASM_OMAP_GPMC_H
+#define __ASM_OMAP_GPMC_H
+
+#define GPMC_BUF_EMPTY 0
+#define GPMC_BUF_FULL 1
+
+enum omap_ecc {
+ /* 1-bit ECC calculation by Software, Error detection by Software */
+ OMAP_ECC_HAM1_CODE_SW = 1, /* avoid un-initialized int can be 0x0 */
+ /* 1-bit ECC calculation by GPMC, Error detection by Software */
+ /* ECC layout compatible to legacy ROMCODE. */
+ OMAP_ECC_HAM1_CODE_HW,
+ /* 4-bit ECC calculation by GPMC, Error detection by Software */
+ OMAP_ECC_BCH4_CODE_HW_DETECTION_SW,
+ /* 4-bit ECC calculation by GPMC, Error detection by ELM */
+ OMAP_ECC_BCH4_CODE_HW,
+ /* 8-bit ECC calculation by GPMC, Error detection by Software */
+ OMAP_ECC_BCH8_CODE_HW_DETECTION_SW,
+ /* 8-bit ECC calculation by GPMC, Error detection by ELM */
+ OMAP_ECC_BCH8_CODE_HW,
+};
+
+struct gpmc_cs {
+ u32 config1; /* 0x00 */
+ u32 config2; /* 0x04 */
+ u32 config3; /* 0x08 */
+ u32 config4; /* 0x0C */
+ u32 config5; /* 0x10 */
+ u32 config6; /* 0x14 */
+ u32 config7; /* 0x18 */
+ u32 nand_cmd; /* 0x1C */
+ u32 nand_adr; /* 0x20 */
+ u32 nand_dat; /* 0x24 */
+ u8 res[8]; /* blow up to 0x30 byte */
+};
+
+struct bch_res_0_3 {
+ u32 bch_result_x[4];
+};
+
+struct gpmc {
+ u8 res1[0x10];
+ u32 sysconfig; /* 0x10 */
+ u8 res2[0x4];
+ u32 irqstatus; /* 0x18 */
+ u32 irqenable; /* 0x1C */
+ u8 res3[0x20];
+ u32 timeout_control; /* 0x40 */
+ u8 res4[0xC];
+ u32 config; /* 0x50 */
+ u32 status; /* 0x54 */
+ u8 res5[0x8]; /* 0x58 */
+ struct gpmc_cs cs[8]; /* 0x60, 0x90, .. */
+ u8 res6[0x14]; /* 0x1E0 */
+ u32 ecc_config; /* 0x1F4 */
+ u32 ecc_control; /* 0x1F8 */
+ u32 ecc_size_config; /* 0x1FC */
+ u32 ecc1_result; /* 0x200 */
+ u32 ecc2_result; /* 0x204 */
+ u32 ecc3_result; /* 0x208 */
+ u32 ecc4_result; /* 0x20C */
+ u32 ecc5_result; /* 0x210 */
+ u32 ecc6_result; /* 0x214 */
+ u32 ecc7_result; /* 0x218 */
+ u32 ecc8_result; /* 0x21C */
+ u32 ecc9_result; /* 0x220 */
+ u8 res7[12]; /* 0x224 */
+ u32 testmomde_ctrl; /* 0x230 */
+ u8 res8[12]; /* 0x234 */
+ struct bch_res_0_3 bch_result_0_3[2]; /* 0x240 */
+};
+
+/* Used for board specific gpmc initialization */
+extern struct gpmc *gpmc_cfg;
+
+#endif /* __ASM_OMAP_GPMC_H */