summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--include/configs/bf533-ezkit.h286
-rw-r--r--include/configs/bf533-stamp.h436
-rw-r--r--include/configs/bf537-stamp.h441
-rw-r--r--include/configs/bf561-ezkit.h295
-rw-r--r--include/configs/bfin_adi_common.h198
5 files changed, 719 insertions, 937 deletions
diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h
index 48c0252..eb08890 100644
--- a/include/configs/bf533-ezkit.h
+++ b/include/configs/bf533-ezkit.h
@@ -2,213 +2,155 @@
* U-boot - Configuration file for BF533 EZKIT board
*/
-#ifndef __CONFIG_EZKIT533_H__
-#define __CONFIG_EZKIT533_H__
+#ifndef __CONFIG_BF533_EZKIT_H__
+#define __CONFIG_BF533_EZKIT_H__
#include <asm/blackfin-config-pre.h>
-#define CONFIG_BAUDRATE 57600
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_LOADADDR 0x01000000 /* default load address */
-#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
-/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x20310300
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 27000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 22
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
-#if 0
-#define CONFIG_MII
-#define CONFIG_SYS_DISCOVER_PHY
-#endif
-#define CONFIG_RTC_BFIN 1
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-
-#define CONFIG_PANIC_HANG 1
-
-#define CONFIG_BFIN_CPU bf533-0.3
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 27000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 22
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+/*
+ * Memory Settings
+ */
+#define CONFIG_MEM_SIZE 32
+/* Early EZKITs had 32megs, but later have 64megs */
+#if (CONFIG_MEM_SIZE == 64)
+# define CONFIG_MEM_ADD_WDTH 10
#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+# define CONFIG_MEM_ADD_WDTH 9
#endif
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
+#define CONFIG_EBIU_SDRRC_VAL 0x398
+#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
-#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC16M16A2TG_75 1
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-#define CONFIG_LOADS_ECHO 1
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
/*
- * BOOTP options
+ * Network Settings
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20310300
+#define SMC91111_EEPROM_INIT() \
+ do { \
+ *pFIO_DIR |= PF1; \
+ *pFIO_FLAG_S = PF1; \
+ SSYNC(); \
+ } while (0)
+#define CONFIG_HOSTNAME bf533-ezkit
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
- * Command line configuration.
+ * Flash Settings
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_DATE
-
-
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
-
-#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
-#define CONFIG_SYS_LOAD_ADDR 0x01000000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
#define CONFIG_SYS_FLASH_BASE 0x20000000
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_SIZE 0x4000
-#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
-
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_FLASH0_BASE 0x20000000
-#define CONFIG_SYS_FLASH1_BASE 0x20200000
-#define CONFIG_SYS_FLASH2_BASE 0x20280000
-#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_SYS_MAX_FLASH_BANKS 3
+#define CONFIG_SYS_MAX_FLASH_SECT 40
+#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR 0x20020000
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
-
-/* JFFS Partition offset set */
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
-
-
-/*
- * Stack sizes
- */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
-#define POLL_MODE 1
+#define CONFIG_ENV_SECT_SIZE 0x10000
#define FLASH_TOT_SECT 40
-#define FLASH_SIZE 0x220000
-#define CONFIG_SYS_FLASH_SIZE 0x220000
-/*
- * Initialize PSD4256 registers for using I2C
- */
-#define CONFIG_MISC_INIT_R
/*
- * I2C settings
+ * I2C Settings
* By default PF1 is used as SDA and PF0 as SCL on the Stamp board
*/
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PF_SCL PF0
-#define PF_SDA PF1
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+#define CONFIG_SOFT_I2C
+#ifdef CONFIG_SOFT_I2C
+#define PF_SCL PF0
+#define PF_SDA PF1
+#define I2C_INIT \
+ do { \
+ *pFIO_DIR |= PF_SCL; \
+ SSYNC(); \
+ } while (0)
+#define I2C_ACTIVE \
+ do { \
+ *pFIO_DIR |= PF_SDA; \
+ *pFIO_INEN &= ~PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_TRISTATE \
+ do { \
+ *pFIO_DIR &= ~PF_SDA; \
+ *pFIO_INEN |= PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0)
+#define I2C_SDA(bit) \
+ do { \
+ if (bit) \
+ *pFIO_FLAG_S = PF_SDA; \
+ else \
+ *pFIO_FLAG_C = PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_SCL(bit) \
+ do { \
+ if (bit) \
+ *pFIO_FLAG_S = PF_SCL; \
+ else \
+ *pFIO_FLAG_C = PF_SCL; \
+ SSYNC(); \
+ } while (0)
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CONFIG_SYS_I2C_SPEED 50000
#define CONFIG_SYS_I2C_SLAVE 0
+#endif
-#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
-#define CONFIG_EBIU_SDRRC_VAL 0x398
-#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
-#define CONFIG_EBIU_SDBCTL_VAL 0x13
+/*
+ * Misc Settings
+ */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
+
-#define CONFIG_EBIU_AMGCTL_VAL 0xFF
-#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
-#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
#include <asm/blackfin-config-post.h>
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index ee41c7e..622f54c 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -2,371 +2,219 @@
* U-boot - Configuration file for BF533 STAMP board
*/
-#ifndef __CONFIG_STAMP_H__
-#define __CONFIG_STAMP_H__
+#ifndef __CONFIG_BF533_STAMP_H__
+#define __CONFIG_BF533_STAMP_H__
#include <asm/blackfin-config-pre.h>
-#define CONFIG_RTC_BFIN 1
-
-#define CONFIG_PANIC_HANG 1
-
-#define CONFIG_BFIN_CPU bf533-0.3
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
/*
- * Board settings
+ * Processor Settings
*/
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x20300300
-
-/* FLASH/ETHERNET uses the same address range */
-#define SHARED_RESOURCES 1
+#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-/* Is I2C bit-banged? */
-#define CONFIG_SOFT_I2C 1
/*
- * Software (bit-bang) I2C driver configuration
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
-#define PF_SCL PF3
-#define PF_SDA PF2
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 11059200
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 36
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
-/*
- * Video splash screen support
- */
-#define CONFIG_VIDEO 0
/*
- * Clock settings
+ * Memory Settings
*/
+#define CONFIG_MEM_ADD_WDTH 11
+#define CONFIG_MEM_SIZE 128
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 11059200
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 36
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
-
-/*
- * Network settings
- */
+#define CONFIG_EBIU_SDRRC_VAL 0x268
+#define CONFIG_EBIU_SDGCTL_VAL 0x911109
-#if (CONFIG_DRIVER_SMC91111)
-#if 0
-#define CONFIG_MII
-#endif
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
-/* network support */
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME STAMP
-#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
-/* To remove hardcoding and enable MAC storage in EEPROM */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
-#endif /* CONFIG_DRIVER_SMC91111 */
/*
- * Flash settings
+ * Network Settings
*/
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20300300
+#define SMC91111_EEPROM_INIT() \
+ do { \
+ *pFIO_DIR |= PF1; \
+ *pFIO_FLAG_S = PF1; \
+ SSYNC(); \
+ } while (0)
+#define CONFIG_HOSTNAME bf533-stamp
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-
-#define CONFIG_SYS_FLASH_BASE 0x20000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-
-#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CONFIG_ENV_OFFSET 0x4000
-#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
-#else
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0x20004000
-#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
-#endif
-
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
-#define ENV_IS_EMBEDDED
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
-#define CONFIG_SYS_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-
-/* JFFS Partition offset set */
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
-
-/*
- * following timeouts shall be used once the
- * Flash real protection is enabled
- */
-#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
-
-/*
- * SDRAM settings & memory map
- */
-
-#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024)
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MAX_RAM_SIZE - 0x80000 - 1)
-#define CONFIG_LOADADDR 0x01000000
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - 0x40000)
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
-
-/* Check to make sure everything fits in SDRAM */
-#if ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) > CONFIG_SYS_MAX_RAM_SIZE)
- #error Memory Map does not fit into configuration
-#endif
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
/*
- * Command settings
+ * Flash Settings
*/
-
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-
-#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
-
-/* configuration lookup from the BOOTP/DHCP server, */
-/* but not try to load any image using TFTP */
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND "run ramboot"
-
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
- "$(rootpath) console=ttyBF0,57600\0" \
- "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux; " \
- "run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux; " \
- "run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- "update=tftpboot $(loadaddr) u-boot.bin; " \
- "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
- "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
- ""
-
-#ifdef CONFIG_SOFT_I2C
-#if (!CONFIG_SOFT_I2C)
-#undef CONFIG_SOFT_I2C
-#endif
-#endif
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 67
/*
- * BOOTP options
+ * SPI Settings
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ 30000000
+#define CONFIG_SF_DEFAULT_HZ 30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_WINBOND
/*
- * Command line configuration.
+ * Env Storage Settings
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
-
-#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_CMD_PING
-#endif
-
-#if (CONFIG_SOFT_I2C)
-#define CONFIG_CMD_I2C
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x2000
#endif
-
-#define CONFIG_CMD_DHCP
-
-
-/*
- * Console settings
- */
-
-#define CONFIG_BAUDRATE 57600
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define ENV_IS_EMBEDDED_CUSTOM
#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_LOADS_ECHO 1
/*
- * I2C settings
+ * I2C Settings
* By default PF2 is used as SDA and PF3 as SCL on the Stamp board
*/
-#if (CONFIG_SOFT_I2C)
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
+#define CONFIG_SOFT_I2C
+#ifdef CONFIG_SOFT_I2C
+#define PF_SCL PF3
+#define PF_SDA PF2
+#define I2C_INIT \
+ do { \
+ *pFIO_DIR |= PF_SCL; \
+ SSYNC(); \
+ } while (0)
+#define I2C_ACTIVE \
+ do { \
+ *pFIO_DIR |= PF_SDA; \
+ *pFIO_INEN &= ~PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_TRISTATE \
+ do { \
+ *pFIO_DIR &= ~PF_SDA; \
+ *pFIO_INEN |= PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0)
+#define I2C_SDA(bit) \
+ do { \
+ if (bit) \
+ *pFIO_FLAG_S = PF_SDA; \
+ else \
+ *pFIO_FLAG_C = PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_SCL(bit) \
+ do { \
+ if (bit) \
+ *pFIO_FLAG_S = PF_SCL; \
+ else \
+ *pFIO_FLAG_C = PF_SCL; \
+ SSYNC(); \
+ } while (0)
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CONFIG_SYS_I2C_SPEED 50000
#define CONFIG_SYS_I2C_SLAVE 0
-#endif /* CONFIG_SOFT_I2C */
+#endif
+
/*
- * Compact Flash settings
+ * Compact Flash / IDE / ATA Settings
*/
/* Enabled below option for CF support */
-/* #define CONFIG_STAMP_CF 1 */
-
-#if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE)
-
-#define CONFIG_MISC_INIT_R 1
+/* #define CONFIG_STAMP_CF */
+#if defined(CONFIG_STAMP_CF)
+#define CONFIG_MISC_INIT_R
#define CONFIG_DOS_PARTITION 1
-/*
- * IDE/ATA stuff
- */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1)
#define CONFIG_SYS_ATA_BASE_ADDR 0x20200000
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */
#define CONFIG_SYS_ATA_STRIDE 2
+
+#undef CONFIG_EBIU_AMBCTL1_VAL
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
#endif
+
/*
- * Miscellaneous configurable options
+ * Misc Settings
*/
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
-#define CONFIG_SYS_HZ 1000 /* 1ms time tick */
-
-#define CONFIG_SYS_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+/* FLASH/ETHERNET uses the same async bank */
+#define SHARED_RESOURCES 1
-#define CONFIG_SPI
+/* define to enable splash screen support */
+/* #define CONFIG_VIDEO */
-#ifdef CONFIG_VIDEO
-#if (CONFIG_VIDEO)
-#define CONFIG_SPLASH_SCREEN 1
-#define CONFIG_SILENT_CONSOLE 1
-#else
-#undef CONFIG_VIDEO
-#endif
-#endif
/*
- * FLASH organization and environment definitions
+ * Pull in common ADI header for remaining command/environment setup
*/
-
-#define CONFIG_EBIU_SDRRC_VAL 0x268
-#define CONFIG_EBIU_SDGCTL_VAL 0x911109
-#define CONFIG_EBIU_SDBCTL_VAL 0x37
-
-#define CONFIG_EBIU_AMGCTL_VAL 0xFF
-#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
-#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
-#define CF_CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
+#include <configs/bfin_adi_common.h>
#include <asm/blackfin-config-post.h>
diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
index f6399a9..7c35a02 100644
--- a/include/configs/bf537-stamp.h
+++ b/include/configs/bf537-stamp.h
@@ -2,272 +2,144 @@
* U-boot - Configuration file for BF537 STAMP board
*/
-#ifndef __CONFIG_BF537_H__
-#define __CONFIG_BF537_H__
+#ifndef __CONFIG_BF537_STAMP_H__
+#define __CONFIG_BF537_STAMP_H__
#include <asm/blackfin-config-pre.h>
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_BAUDRATE 57600
-/* Set default serial console for bf537 */
-#define CONFIG_UART_CONSOLE 0
-#define CONFIG_BOOTDELAY 5
-/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/
-/*#define CONFIG_BF537_STAMP_LEDCMD 1*/
-
-#define CONFIG_PANIC_HANG 1
-#define CONFIG_BFIN_CPU bf537-0.2
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-#define CONFIG_BFIN_MAC
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU bf537-0.2
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
-/* Define if want to do post memory test */
-#undef CONFIG_POST_TEST
-
-#define CONFIG_RTC_BFIN 1
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 25000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL*/
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 25000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 20
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
-/* Values can range from 1-15 */
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC32M8A2_75 1
-#define CONFIG_LOADS_ECHO 1
/*
- * rarpb, bootp or dhcp commands will perform only a
- * configuration lookup from the BOOTP/DHCP server
- * but not try to load any image using TFTP
+ * Memory Settings
*/
-#define CONFIG_SYS_AUTOLOAD "no"
+#define CONFIG_MEM_ADD_WDTH 10
+#define CONFIG_MEM_SIZE 64
+
+#define CONFIG_EBIU_SDRRC_VAL 0x306
+#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
+
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
+
/*
* Network Settings
*/
-/* network support */
-#ifdef CONFIG_BFIN_MAC
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME BF537
+#ifndef __ADSPBF534__
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_BFIN_MAC
+#define CONFIG_NETCONSOLE 1
+#define CONFIG_NET_MULTI 1
#endif
-
-#define CONFIG_ROOTPATH /romfs
+#define CONFIG_HOSTNAME bf537-stamp
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */
-
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND "run ramboot"
-
-#if defined(CONFIG_POST_TEST)
-/* POST support */
-#define CONFIG_POST ( CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_UART | \
- CONFIG_SYS_POST_FLASH | \
- CONFIG_SYS_POST_ETHER | \
- CONFIG_SYS_POST_LED | \
- CONFIG_SYS_POST_BUTTON)
-#else
-#undef CONFIG_POST
-#endif
-#ifdef CONFIG_POST
-#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
-#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
-#endif
-
-/* CF-CARD IDE-HDD Support */
-
-/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */
-/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */
-/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */
-
-#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE)
-# define CONFIG_BFIN_IDE 1
-#endif
-
-/*#define CONFIG_BF537_NAND */ /* Add nand flash support */
-
-#define CONFIG_NETCONSOLE 1
-#define CONFIG_NET_MULTI 1
/*
- * BOOTP options
+ * Flash Settings
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
+#define CONFIG_SYS_MAX_FLASH_SECT 71
/*
- * Command line configuration.
+ * SPI Settings
*/
-#include <config_cmd_default.h>
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ 30000000
+#define CONFIG_SF_DEFAULT_HZ 30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_WINBOND
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
-#ifndef CONFIG_BFIN_MAC
-#undef CONFIG_CMD_NET
+/*
+ * Env Storage Settings
+ */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x2000
#else
-#define CONFIG_CMD_PING
-#endif
-
-#if defined(CONFIG_BFIN_CF_IDE) \
- || defined(CONFIG_BFIN_HDD_IDE) \
- || defined(CONFIG_BFIN_TRUE_IDE)
-#define CONFIG_CMD_IDE
-#endif
-
-#define CONFIG_CMD_DHCP
-
-#if defined(CONFIG_POST)
-#define CONFIG_CMD_DIAG
-#endif
-
-#ifdef CONFIG_BF537_NAND
-#define CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x2000
#endif
-
-
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
-#define CONFIG_LOADADDR 0x1000000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux;" \
- "run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux;" \
- "run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- "update=tftpboot $(loadaddr) u-boot.bin;" \
- "protect off 0x20000000 0x2007FFFF;" \
- "erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0" \
- ""
-
-#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define ENV_IS_EMBEDDED_CUSTOM
#endif
-#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024*1024)
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_FLASH_BASE 0x20000000
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_SIZE 0x4000
-#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
-#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#define CONFIG_ENV_OFFSET 0x4000
-#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */
-#else
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0x20004000
-#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
-#endif
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
-#define ENV_IS_EMBEDDED
-
-/* JFFS Partition offset set */
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 15
+/*
+ * I2C Settings
+ */
+#define CONFIG_BFIN_TWI_I2C 1
+#define CONFIG_HARD_I2C 1
+#define CONFIG_SYS_I2C_SPEED 50000
+#define CONFIG_SYS_I2C_SLAVE 0
-#define CONFIG_SPI
/*
- * Stack sizes
+ * SPI_MMC Settings
*/
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#define CONFIG_MMC
+#define CONFIG_BFIN_SPI_MMC
-#define POLL_MODE 1
-#define FLASH_TOT_SECT 71
-#define FLASH_SIZE 0x400000
-#define CONFIG_SYS_FLASH_SIZE 0x400000
/*
- * Board NAND Infomation
+ * NAND Settings
*/
+/* #define CONFIG_BF537_NAND */
+#ifdef CONFIG_BF537_NAND
+# define CONFIG_CMD_NAND
+#endif
#define CONFIG_SYS_NAND_ADDR 0x20212000
#define CONFIG_SYS_NAND_BASE CONFIG_SYS_NAND_ADDR
@@ -280,56 +152,35 @@
#define NAND_MAX_FLOORS 1
#define BFIN_NAND_READY PF3
-#define NAND_WAIT_READY(nand) \
- do { \
- int timeout = 0; \
- while(!(*pPORTFIO & PF3)) \
- if (timeout++ > 100000) \
- break; \
+#define NAND_WAIT_READY(nand) \
+ do { \
+ int timeout = 0; \
+ while (!(*pPORTFIO & PF3)) \
+ if (timeout++ > 100000) \
+ break; \
} while (0)
-#define BFIN_NAND_CLE (1<<2) /* A2 -> Command Enable */
-#define BFIN_NAND_ALE (1<<1) /* A1 -> Address Enable */
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-/*
- * Initialize PSD4256 registers for using I2C
- */
-#define CONFIG_MISC_INIT_R
+#define BFIN_NAND_CLE (1 << 2) /* A2 -> Command Enable */
+#define BFIN_NAND_ALE (1 << 1) /* A1 -> Address Enable */
+#define WRITE_NAND_COMMAND(d, adr) bfin_write8(adr | BFIN_NAND_CLE, d)
+#define WRITE_NAND_ADDRESS(d, adr) bfin_write8(adr | BFIN_NAND_ALE, d)
+#define WRITE_NAND(d, adr) bfin_write8(adr, d)
+#define READ_NAND(adr) bfin_read8(adr)
-#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
/*
- * I2C settings
+ * CF-CARD IDE-HDD Support
*/
-#define CONFIG_HARD_I2C 1
-#define CONFIG_BFIN_TWI_I2C 1
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0
-
-#define CONFIG_EBIU_SDRRC_VAL 0x306
-#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
-#define CONFIG_EBIU_SDBCTL_VAL 0x25
-
-#define CONFIG_EBIU_AMGCTL_VAL 0xFF
-#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
-#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
- ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
- B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
+/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */
+/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */
+/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
+#if defined(CONFIG_BFIN_CF_IDE) || \
+ defined(CONFIG_BFIN_HDD_IDE) || \
+ defined(CONFIG_BFIN_TRUE_IDE)
+# define CONFIG_BFIN_IDE 1
+# define CONFIG_CMD_IDE
+#endif
#if defined(CONFIG_BFIN_IDE)
@@ -341,11 +192,11 @@
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1)
-#undef AMBCTL1VAL
-#define AMBCTL1VAL 0xFFC3FFC3
+#undef CONFIG_EBIU_AMBCTL1_VAL
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3
#define CONFIG_CF_ATASEL_DIS 0x20311800
#define CONFIG_CF_ATASEL_ENA 0x20311802
@@ -357,34 +208,54 @@
*/
#define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */
#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.Ax */
-#endif /* CONFIG_BFIN_TRUE_IDE */
-#if defined(CONFIG_BFIN_CF_IDE) /* USE CompactFlash Storage Card in the common memory space */
+#elif defined(CONFIG_BFIN_CF_IDE)
#define CONFIG_SYS_ATA_BASE_ADDR 0x20211800
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */
#define CONFIG_SYS_ATA_STRIDE 1 /* CF.A0 --> Blackfin.Ax */
-#endif /* CONFIG_BFIN_CF_IDE */
-#if defined(CONFIG_BFIN_HDD_IDE) /* USE TRUE IDE */
+#elif defined(CONFIG_BFIN_HDD_IDE)
#define CONFIG_SYS_ATA_BASE_ADDR 0x20314000
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */
#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */
-
#undef CONFIG_SCLK_DIV
#define CONFIG_SCLK_DIV 8
-#endif /* CONFIG_BFIN_HDD_IDE */
+#endif
+
+#endif
-#endif /*CONFIG_BFIN_IDE */
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
+
+/* #define CONFIG_BF537_STAMP_LEDCMD 1 */
+
+/* Define if want to do post memory test */
+#undef CONFIG_POST
+#ifdef CONFIG_POST
+#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
+#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
+#endif
+
+
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
#include <asm/blackfin-config-post.h>
diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
index 320a8c6..ef2019f 100644
--- a/include/configs/bf561-ezkit.h
+++ b/include/configs/bf561-ezkit.h
@@ -2,229 +2,152 @@
* U-boot - Configuration file for BF561 EZKIT board
*/
-#ifndef __CONFIG_EZKIT561_H__
-#define __CONFIG_EZKIT561_H__
+#ifndef __CONFIG_BF561_EZKIT_H__
+#define __CONFIG_BF561_EZKIT_H__
#include <asm/blackfin-config-pre.h>
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_BAUDRATE 57600
-/* Set default serial console for bf537 */
-#define CONFIG_UART_CONSOLE 0
-#define CONFIG_EZKIT561 1
-#define CONFIG_BOOTDELAY 5
-
-#define CONFIG_PANIC_HANG 1
-
-#define CONFIG_BFIN_CPU bf561-0.3
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
/*
- * Board settings
+ * Processor Settings
*/
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x2C010300
-#define CONFIG_ASYNC_EBIU_BASE CONFIG_SMC91111_BASE & ~(4*1024*1024)
-#define CONFIG_SMC_USE_32_BIT 1
-#define CONFIG_MISC_INIT_R 1
-
-/*
- * Clock settings
- */
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 30000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 20
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
+#define CONFIG_BFIN_CPU bf561-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-/*
- * Network settings
- */
-#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME ezkit561
-#define CONFIG_ROOTPATH /arm-cross-build/BF561/uClinux-dist/romfs
-#endif /* CONFIG_DRIVER_SMC91111 */
/*
- * Flash settings
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 30000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 20
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 6
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_SYS_FLASH_BASE 0x20000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max number of sectors on one chip */
-#define CONFIG_ENV_ADDR 0x20020000
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
-/* JFFS Partition offset set */
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 8
/*
- * SDRAM settings & memory map
+ * Memory Settings
*/
+#define CONFIG_MEM_ADD_WDTH 9
+#define CONFIG_MEM_SIZE 64
-#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC16M16A2TG_75 1
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
-
-#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */
+#define CONFIG_EBIU_SDRRC_VAL 0x306
+#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
-#define CONFIG_LOADADDR 0x01000000 /* default load address */
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_EBIU_AMGCTL_VAL 0x3F
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
-#define CONFIG_SYS_GBL_DATA_SIZE 0x4000
-#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
-
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
/*
- * Command settings
+ * Network Settings
*/
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x2C010300
+#define CONFIG_SMC_USE_32_BIT 1
+#define CONFIG_HOSTNAME bf561-ezkit
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-#define CONFIG_SYS_AUTOLOAD "no" /* rarpb, bootp, dhcp commands will */
- /* only perform a configuration */
- /* lookup from the BOOTP/DHCP server */
- /* but not try to load any image */
- /* using TFTP */
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, */
- /* currently its disabled */
-#define CONFIG_BOOTCOMMAND "run ramboot"
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
-
-#if (CONFIG_DRIVER_SMC91111)
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
- "$(rootpath) console=ttyBF0,57600\0" \
- "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux; " \
- "run ramargs; run addip; bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux; " \
- "run nfsargs; run addip; bootelf\0" \
- "update=tftpboot $(loadaddr) u-boot.bin; " \
- "protect off 0x20000000 0x2003FFFF; " \
- "erase 0x20000000 0x2003FFFF; " \
- "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
- ""
-#else
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "flashboot=bootm 0x20100000\0" \
- ""
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
/*
- * Command line configuration.
+ * Flash Settings
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-
-#if defined(CONFIG_DRIVER_SMC91111)
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 135
+/* The BF561-EZKIT uses a top boot flash */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x20004000
+#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
+#else
+#define ENV_IS_EMBEDDED_CUSTOM
#endif
+
/*
- * Console settings
+ * I2C Settings
*/
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SOFT_I2C
+#ifdef CONFIG_SOFT_I2C
+#define PF_SCL PF0
+#define PF_SDA PF1
+#define I2C_INIT \
+ do { \
+ *pFIO0_DIR |= PF_SCL; \
+ SSYNC(); \
+ } while (0)
+#define I2C_ACTIVE \
+ do { \
+ *pFIO0_DIR |= PF_SDA; \
+ *pFIO0_INEN &= ~PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_TRISTATE \
+ do { \
+ *pFIO0_DIR &= ~PF_SDA; \
+ *pFIO0_INEN |= PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0)
+#define I2C_SDA(bit) \
+ do { \
+ if (bit) \
+ *pFIO0_FLAG_S = PF_SDA; \
+ else \
+ *pFIO0_FLAG_C = PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_SCL(bit) \
+ do { \
+ if (bit) \
+ *pFIO0_FLAG_S = PF_SCL; \
+ else \
+ *pFIO0_FLAG_C = PF_SCL; \
+ SSYNC(); \
+ } while (0)
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CONFIG_SYS_I2C_SPEED 50000
+#define CONFIG_SYS_I2C_SLAVE 0
#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_LOADS_ECHO 1
/*
- * Miscellaneous configurable options
+ * Misc Settings
*/
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */
-#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
+#define CONFIG_UART_CONSOLE 0
+
/*
- * FLASH organization and environment definitions
+ * Pull in common ADI header for remaining command/environment setup
*/
-#define CONFIG_EBIU_SDRRC_VAL 0x306
-#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
-#define CONFIG_EBIU_SDBCTL_VAL 0x15
-
-#define CONFIG_EBIU_AMGCTL_VAL 0x3F
-#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
-#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+#include <configs/bfin_adi_common.h>
#include <asm/blackfin-config-post.h>
diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h
new file mode 100644
index 0000000..6afce4d
--- /dev/null
+++ b/include/configs/bfin_adi_common.h
@@ -0,0 +1,198 @@
+/*
+ * U-Boot - Common settings for Analog Devices boards
+ */
+
+#ifndef __CONFIG_BFIN_ADI_COMMON_H__
+#define __CONFIG_BFIN_ADI_COMMON_H__
+
+/*
+ * Command Settings
+ */
+#ifndef _CONFIG_CMD_DEFAULT_H
+# include <config_cmd_default.h>
+# if ADI_CMDS_NETWORK
+# define CONFIG_CMD_DHCP
+# define CONFIG_CMD_PING
+# ifdef CONFIG_BFIN_MAC
+# define CONFIG_CMD_MII
+# endif
+# else
+# undef CONFIG_CMD_BOOTD
+# undef CONFIG_CMD_NET
+# undef CONFIG_CMD_NFS
+# endif
+# ifdef CONFIG_LIBATA
+# define CONFIG_CMD_FAT
+# define CONFIG_CMD_SATA
+# define CONFIG_DOS_PARTITION
+# endif
+# ifdef CONFIG_MMC
+# define CONFIG_CMD_FAT
+# define CONFIG_CMD_MMC
+# define CONFIG_DOS_PARTITION
+# endif
+# ifdef CONFIG_USB
+# define CONFIG_CMD_EXT2
+# define CONFIG_CMD_FAT
+# define CONFIG_CMD_USB
+# define CONFIG_CMD_USB_STORAGE
+# define CONFIG_DOS_PARTITION
+# endif
+# ifdef CONFIG_POST
+# define CONFIG_CMD_DIAG
+# endif
+# ifdef CONFIG_RTC_BFIN
+# define CONFIG_CMD_DATE
+# endif
+# ifdef CONFIG_SPI
+# define CONFIG_CMD_EEPROM
+# endif
+# if defined(CONFIG_BFIN_SPI) || defined(CONFIG_SOFT_SPI)
+# define CONFIG_CMD_SPI
+# endif
+# ifdef CONFIG_SPI_FLASH
+# define CONFIG_CMD_SF
+# endif
+# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+# define CONFIG_CMD_I2C
+# endif
+# ifdef CONFIG_SYS_NO_FLASH
+# undef CONFIG_CMD_FLASH
+# undef CONFIG_CMD_IMLS
+# else
+# define CONFIG_CMD_JFFS2
+# endif
+# define CONFIG_CMD_BOOTLDR
+# define CONFIG_CMD_CACHE
+# define CONFIG_CMD_CPLBINFO
+# define CONFIG_CMD_ELF
+# define CONFIG_ELF_SIMPLE_LOAD
+# define CONFIG_CMD_REGINFO
+# define CONFIG_CMD_STRINGS
+# if defined(__ADSPBF51x__) || defined(__ADSPBF52x__) || defined(__ADSPBF54x__)
+# define CONFIG_CMD_OTP
+# endif
+#endif
+
+/*
+ * Console Settings
+ */
+#define CONFIG_SYS_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE 1
+#define CONFIG_LOADS_ECHO 1
+#define CONFIG_JTAG_CONSOLE
+#ifndef CONFIG_BAUDRATE
+# define CONFIG_BAUDRATE 57600
+#endif
+
+/*
+ * Debug Settings
+ */
+#define CONFIG_ENV_OVERWRITE 1
+#define CONFIG_DEBUG_DUMP 1
+#define CONFIG_DEBUG_DUMP_SYMS 1
+#define CONFIG_PANIC_HANG 1
+
+/*
+ * Env Settings
+ */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART)
+# define CONFIG_BOOTDELAY -1
+#else
+# define CONFIG_BOOTDELAY 5
+#endif
+#define CONFIG_BOOTCOMMAND "run ramboot"
+#ifdef CONFIG_VIDEO
+# define CONFIG_BOOTARGS_VIDEO "console=tty0 "
+#else
+# define CONFIG_BOOTARGS_VIDEO ""
+#endif
+#define CONFIG_BOOTARGS \
+ "root=/dev/mtdblock0 rw " \
+ "earlyprintk=" \
+ "serial," \
+ "uart" MK_STR(CONFIG_UART_CONSOLE) "," \
+ MK_STR(CONFIG_BAUDRATE) " " \
+ CONFIG_BOOTARGS_VIDEO \
+ "console=ttyBF0," MK_STR(CONFIG_BAUDRATE)
+
+#if defined(CONFIG_CMD_NET)
+# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+# define UBOOT_ENV_FILE "u-boot.bin"
+# else
+# define UBOOT_ENV_FILE "u-boot.ldr"
+# endif
+# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+# ifdef CONFIG_SPI
+# define UBOOT_ENV_UPDATE \
+ "eeprom write $(loadaddr) 0x0 $(filesize)"
+# else
+# define UBOOT_ENV_UPDATE \
+ "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \
+ "sf erase 0 0x40000;" \
+ "sf write $(loadaddr) 0 $(filesize)"
+# endif
+# elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
+# define UBOOT_ENV_UPDATE \
+ "nand unlock 0 0x40000;" \
+ "nand erase 0 0x40000;" \
+ "nand write $(loadaddr) 0 0x40000"
+# else
+# define UBOOT_ENV_UPDATE \
+ "protect off 0x20000000 0x2003FFFF;" \
+ "erase 0x20000000 0x2003FFFF;" \
+ "cp.b $(loadaddr) 0x20000000 $(filesize)"
+# endif
+# define NETWORK_ENV_SETTINGS \
+ "ubootfile=" UBOOT_ENV_FILE "\0" \
+ "update=" \
+ "tftp $(loadaddr) $(ubootfile);" \
+ UBOOT_ENV_UPDATE \
+ "\0" \
+ "addip=set bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \
+ "$(hostname):eth0:off" \
+ "\0" \
+ "ramargs=set bootargs " CONFIG_BOOTARGS "\0" \
+ "ramboot=" \
+ "tftp $(loadaddr) uImage;" \
+ "run ramargs;" \
+ "run addip;" \
+ "bootm" \
+ "\0" \
+ "nfsargs=set bootargs " \
+ "root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \
+ "\0" \
+ "nfsboot=" \
+ "tftp $(loadaddr) vmImage;" \
+ "run nfsargs;" \
+ "run addip;" \
+ "bootm" \
+ "\0"
+#else
+# define NETWORK_ENV_SETTINGS
+#endif
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ NETWORK_ENV_SETTINGS \
+ "flashboot=bootm 0x20100000\0"
+
+/*
+ * Network Settings
+ */
+#ifdef CONFIG_CMD_NET
+# define CONFIG_IPADDR 192.168.0.15
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_GATEWAYIP 192.168.0.1
+# define CONFIG_SERVERIP 192.168.0.2
+# define CONFIG_ROOTPATH /romfs
+# ifdef CONFIG_CMD_DHCP
+# ifndef CONFIG_SYS_AUTOLOAD
+# define CONFIG_SYS_AUTOLOAD "no"
+# endif
+# endif
+# define CONFIG_NET_RETRY_COUNT 20
+#endif
+
+#endif