diff options
| -rw-r--r-- | README | 12 | ||||
| -rw-r--r-- | drivers/serial/serial_pl01x.c | 30 | ||||
| -rw-r--r-- | drivers/serial/serial_pl01x.h | 4 |
3 files changed, 43 insertions, 3 deletions
@@ -475,6 +475,18 @@ The following options need to be configured: define this to a list of base addresses for each (supported) port. See e.g. include/configs/versatile.h + CONFIG_PL011_SERIAL_RLCR + + Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500) + have separate receive and transmit line control registers. Set + this variable to initialize the extra register. + + CONFIG_PL011_SERIAL_FLUSH_ON_INIT + + On some platforms (e.g. U8500) U-Boot is loaded by a second stage + boot loader that has already initialized the UART. Define this + variable to flush the UART at init time. + - Console Interface: Depending on board, define exactly one serial port diff --git a/drivers/serial/serial_pl01x.c b/drivers/serial/serial_pl01x.c index 5dfcde8..7a064ff 100644 --- a/drivers/serial/serial_pl01x.c +++ b/drivers/serial/serial_pl01x.c @@ -111,6 +111,15 @@ int serial_init (void) unsigned int divider; unsigned int remainder; unsigned int fraction; + unsigned int lcr; + +#ifdef CONFIG_PL011_SERIAL_FLUSH_ON_INIT + /* Empty RX fifo if necessary */ + if (readl(®s->pl011_cr) & UART_PL011_CR_UARTEN) { + while (!(readl(®s->fr) & UART_PL01x_FR_RXFE)) + readl(®s->dr); + } +#endif /* First, disable everything */ writel(0, ®s->pl011_cr); @@ -131,9 +140,24 @@ int serial_init (void) writel(fraction, ®s->pl011_fbrd); /* Set the UART to be 8 bits, 1 stop bit, no parity, fifo enabled */ - writel(UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN, - ®s->pl011_lcrh); - + lcr = UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN; + writel(lcr, ®s->pl011_lcrh); + +#ifdef CONFIG_PL011_SERIAL_RLCR + { + int i; + + /* + * Program receive line control register after waiting + * 10 bus cycles. Delay be writing to readonly register + * 10 times + */ + for (i = 0; i < 10; i++) + writel(lcr, ®s->fr); + + writel(lcr, ®s->pl011_rlcr); + } +#endif /* Finally, enable the UART */ writel(UART_PL011_CR_UARTEN | UART_PL011_CR_TXE | UART_PL011_CR_RXE, ®s->pl011_cr); diff --git a/drivers/serial/serial_pl01x.h b/drivers/serial/serial_pl01x.h index b670c24..96ee381 100644 --- a/drivers/serial/serial_pl01x.h +++ b/drivers/serial/serial_pl01x.h @@ -43,7 +43,11 @@ struct pl01x_regs { u32 pl010_lcrl; /* 0x10 Line control register, low byte */ u32 pl010_cr; /* 0x14 Control register */ u32 fr; /* 0x18 Flag register (Read only) */ +#ifdef CONFIG_PL011_SERIAL_RLCR + u32 pl011_rlcr; /* 0x1c Receive line control register */ +#else u32 reserved; +#endif u32 ilpr; /* 0x20 IrDA low-power counter register */ u32 pl011_ibrd; /* 0x24 Integer baud rate register */ u32 pl011_fbrd; /* 0x28 Fractional baud rate register */ |