diff options
| -rw-r--r-- | board/tqc/tqm5200/tqm5200.c | 6 | ||||
| -rw-r--r-- | include/configs/TQM5200.h | 14 |
2 files changed, 10 insertions, 10 deletions
diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c index faa2e02..5a091c4 100644 --- a/board/tqc/tqm5200/tqm5200.c +++ b/board/tqc/tqm5200/tqm5200.c @@ -358,11 +358,9 @@ int post_hotkeys_pressed(void) gpio = (struct mpc5xxx_gpio*) MPC5XXX_GPIO; /* - * Configure PSC6_1 and PSC6_3 as GPIO. PSC6 then couldn't be used in - * CODEC or UART mode. Consumer IrDA should still be possible. + * Configure PSC6_0 through PSC6_3 as GPIO. */ - gpio->port_config &= ~(0x07000000); - gpio->port_config |= 0x03000000; + gpio->port_config &= ~(0x00700000); /* Enable GPIO for GPIO_IRDA_1 (IR_USB_CLK pin) = PSC6_3 */ gpio->simple_gpioe |= 0x20000000; diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index a4336a7..2154c78 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -540,6 +540,8 @@ * 101 -> use PSC6 as UART. Pins PSC6_0 to PSC6_3 are used. * Extended POST test is not available. * Use for STK52xx, FO300 and CAM5200 boards. + * WARNING: When the extended POST is enabled, these bits will + * be overridden by this code as GPIOs! * use PCI_DIS: Bit 16 (mask 0x00008000): * 1 -> disable PCI controller (on CAM5200 board). * use USB: Bits 18-19 (mask 0x00003000): @@ -552,7 +554,7 @@ * 000 -> All PSC2 pins are GPIOs. * 100 -> UART (on CAM5200 board). * 001 -> CAN1/2 on PSC2 pins. - * Use for REV100 STK52xx boards + * Use for REV100 STK52xx boards * 01x -> Use AC97 (on FO300 board). * use PSC1: Bits 29-31 (mask: 0x00000007): * 100 -> UART (on all boards). @@ -711,20 +713,20 @@ #define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA -/* Offset for data I/O */ +/* Offset for data I/O */ #define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) -/* Offset for normal register accesses */ +/* Offset for normal register accesses */ #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) -/* Offset for alternate registers */ +/* Offset for alternate registers */ #define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) -/* Interval between registers */ +/* Interval between registers */ #define CONFIG_SYS_ATA_STRIDE 4 /* Support ATAPI devices */ -#define CONFIG_ATAPI 1 +#define CONFIG_ATAPI 1 /*----------------------------------------------------------------------- * Open firmware flat tree support |