diff options
59 files changed, 2107 insertions, 1807 deletions
diff --git a/blackfin_config.mk b/blackfin_config.mk index f3fcd7a..04a7529 100644 --- a/blackfin_config.mk +++ b/blackfin_config.mk @@ -36,6 +36,7 @@ endif SYM_PREFIX = _ +LDR_FLAGS += -J LDR_FLAGS += --bmode $(subst BFIN_BOOT_,,$(CONFIG_BFIN_BOOT_MODE)) LDR_FLAGS += --use-vmas ifneq ($(CONFIG_BFIN_BOOT_MODE),BFIN_BOOT_BYPASS) diff --git a/board/bf533-ezkit/u-boot.lds.S b/board/bf533-ezkit/u-boot.lds.S index da16726..f80f894 100644 --- a/board/bf533-ezkit/u-boot.lds.S +++ b/board/bf533-ezkit/u-boot.lds.S @@ -44,12 +44,11 @@ OUTPUT_ARCH(bfin) -/* The 0xC offset is so we don't clobber the tiny LDR jump block. */ MEMORY { ram : ORIGIN = CONFIG_SYS_MONITOR_BASE, LENGTH = CONFIG_SYS_MONITOR_LEN - l1_code : ORIGIN = L1_INST_SRAM+0xC, LENGTH = L1_INST_SRAM_SIZE - l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE + l1_code : ORIGIN = L1_INST_SRAM, LENGTH = L1_INST_SRAM_SIZE + l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE } ENTRY(_start) diff --git a/board/bf533-stamp/bf533-stamp.c b/board/bf533-stamp/bf533-stamp.c index 44ebc93..7108dda 100644 --- a/board/bf533-stamp/bf533-stamp.c +++ b/board/bf533-stamp/bf533-stamp.c @@ -1,7 +1,7 @@ /* - * U-boot - stamp.c STAMP board specific routines + * U-boot - main board file * - * Copyright (c) 2005-2007 Analog Devices Inc. + * Copyright (c) 2005-2008 Analog Devices Inc. * * (C) Copyright 2000-2004 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. @@ -31,15 +31,6 @@ DECLARE_GLOBAL_DATA_PTR; -#define STATUS_LED_OFF 0 -#define STATUS_LED_ON 1 - -#ifdef CONFIG_SHOW_BOOT_PROGRESS -# define SHOW_BOOT_PROGRESS(arg) show_boot_progress(arg) -#else -# define SHOW_BOOT_PROGRESS(arg) -#endif - int checkboard(void) { printf("Board: ADI BF533 Stamp board\n"); @@ -192,10 +183,15 @@ void cf_outsw(unsigned short *addr, unsigned short *sect_buf, int words) } #endif -void stamp_led_set(int LED1, int LED2, int LED3) +#ifdef CONFIG_SHOW_BOOT_PROGRESS + +#define STATUS_LED_OFF 0 +#define STATUS_LED_ON 1 + +static void stamp_led_set(int LED1, int LED2, int LED3) { - *pFIO_INEN &= ~(PF2 | PF3 | PF4); - *pFIO_DIR |= (PF2 | PF3 | PF4); + bfin_write_FIO_INEN(bfin_read_FIO_INEN() & ~(PF2 | PF3 | PF4)); + bfin_write_FIO_DIR(bfin_read_FIO_DIR() | (PF2 | PF3 | PF4)); if (LED1 == STATUS_LED_OFF) *pFIO_FLAG_S = PF2; @@ -249,3 +245,41 @@ void show_boot_progress(int status) break; } } +#endif + +#ifdef CONFIG_STATUS_LED +#include <status_led.h> + +static void set_led(int pf, int state) +{ + switch (state) { + case STATUS_LED_OFF: bfin_write_FIO_FLAG_S(pf); break; + case STATUS_LED_BLINKING: bfin_write_FIO_FLAG_T(pf); break; + case STATUS_LED_ON: bfin_write_FIO_FLAG_C(pf); break; + } +} + +static void set_leds(led_id_t mask, int state) +{ + if (mask & 0x1) set_led(PF2, state); + if (mask & 0x2) set_led(PF3, state); + if (mask & 0x4) set_led(PF4, state); +} + +void __led_init(led_id_t mask, int state) +{ + bfin_write_FIO_INEN(bfin_read_FIO_INEN() & ~(PF2 | PF3 | PF4)); + bfin_write_FIO_DIR(bfin_read_FIO_DIR() | (PF2 | PF3 | PF4)); +} + +void __led_set(led_id_t mask, int state) +{ + set_leds(mask, state); +} + +void __led_toggle(led_id_t mask) +{ + set_leds(mask, STATUS_LED_BLINKING); +} + +#endif diff --git a/board/bf533-stamp/u-boot.lds.S b/board/bf533-stamp/u-boot.lds.S index 76daa75..8ddfa81 100644 --- a/board/bf533-stamp/u-boot.lds.S +++ b/board/bf533-stamp/u-boot.lds.S @@ -44,12 +44,11 @@ OUTPUT_ARCH(bfin) -/* The 0xC offset is so we don't clobber the tiny LDR jump block. */ MEMORY { ram : ORIGIN = CONFIG_SYS_MONITOR_BASE, LENGTH = CONFIG_SYS_MONITOR_LEN - l1_code : ORIGIN = L1_INST_SRAM+0xC, LENGTH = L1_INST_SRAM_SIZE - l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE + l1_code : ORIGIN = L1_INST_SRAM, LENGTH = L1_INST_SRAM_SIZE + l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE } ENTRY(_start) diff --git a/board/bf537-stamp/Makefile b/board/bf537-stamp/Makefile index cb38b96..3b875a3 100644 --- a/board/bf537-stamp/Makefile +++ b/board/bf537-stamp/Makefile @@ -29,9 +29,10 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).a -COBJS-y := $(BOARD).o post-memory.o cmd_bf537led.o +COBJS-y := $(BOARD).o cmd_bf537led.o COBJS-$(CONFIG_CMD_EEPROM) += spi_flash.o COBJS-$(CONFIG_CMD_NAND) += nand.o +COBJS-$(CONFIG_POST) += post.o post-memory.o SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) diff --git a/board/bf537-stamp/bf537-stamp.c b/board/bf537-stamp/bf537-stamp.c index 5b619be..16ffe2f 100644 --- a/board/bf537-stamp/bf537-stamp.c +++ b/board/bf537-stamp/bf537-stamp.c @@ -1,7 +1,7 @@ /* - * U-boot - BF537.c + * U-boot - main board file * - * Copyright (c) 2005-2007 Analog Devices Inc. + * Copyright (c) 2005-2008 Analog Devices Inc. * * (C) Copyright 2000-2004 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. @@ -29,15 +29,13 @@ #include <config.h> #include <command.h> #include <asm/blackfin.h> -#include <asm/io.h> +#include <asm/net.h> #include <net.h> #include <asm/mach-common/bits/bootrom.h> #include <netdev.h> DECLARE_GLOBAL_DATA_PTR; -#define POST_WORD_ADDR 0xFF903FFC - int checkboard(void) { printf("Board: ADI BF537 stamp board\n"); @@ -89,22 +87,63 @@ phys_size_t initdram(int board_type) return gd->bd->bi_memsize; } +void board_reset(void) +{ + /* workaround for weak pull ups on ssel */ + if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) { + bfin_write_PORTF_FER(bfin_read_PORTF_FER() & ~PF10); + bfin_write_PORTFIO_SET(PF10); + udelay(1); + } +} + +#ifdef CONFIG_BFIN_MAC +static void board_init_enetaddr(uchar *mac_addr) +{ +#ifdef CONFIG_SYS_NO_FLASH +# define USE_MAC_IN_FLASH 0 +#else +# define USE_MAC_IN_FLASH 1 +#endif + bool valid_mac = false; + + if (USE_MAC_IN_FLASH) { + /* we cram the MAC in the last flash sector */ + uchar *board_mac_addr = (uchar *)0x203F0000; + if (is_valid_ether_addr(board_mac_addr)) { + memcpy(mac_addr, board_mac_addr, 6); + valid_mac = true; + } + } + + if (!valid_mac) { + puts("Warning: Generating 'random' MAC address\n"); + bfin_gen_rand_mac(mac_addr); + } + + eth_setenv_enetaddr("ethaddr", mac_addr); +} + +int board_eth_init(bd_t *bis) +{ + return bfin_EMAC_initialize(bis); +} +#endif + #if defined(CONFIG_MISC_INIT_R) /* miscellaneous platform dependent initialisations */ int misc_init_r(void) { -#if defined(CONFIG_CMD_NET) - char nid[32]; - unsigned char *pMACaddr = (unsigned char *)0x203F0000; +#ifdef CONFIG_BFIN_MAC + uchar enetaddr[6]; + if (!eth_getenv_enetaddr("ethaddr", enetaddr)) + board_init_enetaddr(enetaddr); +#endif - /* The 0xFF check here is to make sure we don't use the address - * in flash if it's simply been erased (aka all 0xFF values) */ - if (getenv("ethaddr") == NULL && is_valid_ether_addr(pMACaddr)) { - sprintf(nid, "%02x:%02x:%02x:%02x:%02x:%02x", - pMACaddr[0], pMACaddr[1], - pMACaddr[2], pMACaddr[3], pMACaddr[4], pMACaddr[5]); - setenv("ethaddr", nid); - } +#ifndef CONFIG_SYS_NO_FLASH + /* we use the last sector for the MAC address / POST LDR */ + extern flash_info_t flash_info[]; + flash_protect(FLAG_PROTECT_SET, 0x203F0000, 0x203FFFFF, &flash_info[0]); #endif #if defined(CONFIG_BFIN_IDE) @@ -126,245 +165,3 @@ int misc_init_r(void) return 0; } #endif /* CONFIG_MISC_INIT_R */ - -#if defined(CONFIG_BFIN_MAC) - -int board_eth_init(bd_t *bis) -{ - return bfin_EMAC_initialize(bis); -} -#endif - -#ifdef CONFIG_POST -/* Using sw10-PF5 as the hotkey */ -int post_hotkeys_pressed(void) -{ - int delay = 3; - int i; - unsigned short value; - - *pPORTF_FER &= ~PF5; - *pPORTFIO_DIR &= ~PF5; - *pPORTFIO_INEN |= PF5; - - printf("########Press SW10 to enter Memory POST########: %2d ", delay); - while (delay--) { - for (i = 0; i < 100; i++) { - value = *pPORTFIO & PF5; - if (value != 0) { - break; - } - udelay(10000); - } - printf("\b\b\b%2d ", delay); - } - printf("\b\b\b 0"); - printf("\n"); - if (value == 0) - return 0; - else { - printf("Hotkey has been pressed, Enter POST . . . . . .\n"); - return 1; - } -} -#endif - -#if defined(CONFIG_POST) || defined(CONFIG_LOGBUFFER) -void post_word_store(ulong a) -{ - volatile ulong *save_addr = (volatile ulong *)POST_WORD_ADDR; - *save_addr = a; -} - -ulong post_word_load(void) -{ - volatile ulong *save_addr = (volatile ulong *)POST_WORD_ADDR; - return *save_addr; -} -#endif - -#ifdef CONFIG_POST -int uart_post_test(int flags) -{ - return 0; -} - -#define BLOCK_SIZE 0x10000 -#define VERIFY_ADDR 0x2000000 -extern int erase_block_flash(int); -extern int write_data(long lStart, long lCount, uchar * pnData); -int flash_post_test(int flags) -{ - unsigned short *pbuf, *temp; - int offset, n, i; - int value = 0; - int result = 0; - printf("\n"); - pbuf = (unsigned short *)VERIFY_ADDR; - temp = pbuf; - for (n = FLASH_START_POST_BLOCK; n < FLASH_END_POST_BLOCK; n++) { - offset = (n - 7) * BLOCK_SIZE; - printf("--------Erase block:%2d..", n); - erase_block_flash(n); - printf("OK\r"); - printf("--------Program block:%2d...", n); - write_data(CONFIG_SYS_FLASH_BASE + offset, BLOCK_SIZE, pbuf); - printf("OK\r"); - printf("--------Verify block:%2d...", n); - for (i = 0; i < BLOCK_SIZE; i += 2) { - if (*(unsigned short *)(CONFIG_SYS_FLASH_BASE + offset + i) != - *temp++) { - value = 1; - result = 1; - } - } - if (value) - printf("failed\n"); - else - printf("OK %3d%%\r", - (int)( - (n + 1 - - FLASH_START_POST_BLOCK) * - 100 / (FLASH_END_POST_BLOCK - - FLASH_START_POST_BLOCK))); - - temp = pbuf; - value = 0; - } - printf("\n"); - if (result) - return -1; - else - return 0; -} - -/**************************************************** - * LED1 ---- PF6 LED2 ---- PF7 * - * LED3 ---- PF8 LED4 ---- PF9 * - * LED5 ---- PF10 LED6 ---- PF11 * - ****************************************************/ -int led_post_test(int flags) -{ - *pPORTF_FER &= ~(PF6 | PF7 | PF8 | PF9 | PF10 | PF11); - *pPORTFIO_DIR |= PF6 | PF7 | PF8 | PF9 | PF10 | PF11; - *pPORTFIO_INEN &= ~(PF6 | PF7 | PF8 | PF9 | PF10 | PF11); - *pPORTFIO &= ~(PF6 | PF7 | PF8 | PF9 | PF10 | PF11); - udelay(1000000); - printf("LED1 on"); - *pPORTFIO |= PF6; - udelay(1000000); - printf("\b\b\b\b\b\b\b"); - printf("LED2 on"); - *pPORTFIO |= PF7; - udelay(1000000); - printf("\b\b\b\b\b\b\b"); - printf("LED3 on"); - *pPORTFIO |= PF8; - udelay(1000000); - printf("\b\b\b\b\b\b\b"); - printf("LED4 on"); - *pPORTFIO |= PF9; - udelay(1000000); - printf("\b\b\b\b\b\b\b"); - printf("LED5 on"); - *pPORTFIO |= PF10; - udelay(1000000); - printf("\b\b\b\b\b\b\b"); - printf("lED6 on"); - *pPORTFIO |= PF11; - printf("\b\b\b\b\b\b\b "); - return 0; -} - -/************************************************ - * SW10 ---- PF5 SW11 ---- PF4 * - * SW12 ---- PF3 SW13 ---- PF2 * - ************************************************/ -int button_post_test(int flags) -{ - int i, delay = 5; - unsigned short value = 0; - int result = 0; - - *pPORTF_FER &= ~(PF5 | PF4 | PF3 | PF2); - *pPORTFIO_DIR &= ~(PF5 | PF4 | PF3 | PF2); - *pPORTFIO_INEN |= (PF5 | PF4 | PF3 | PF2); - - printf("\n--------Press SW10: %2d ", delay); - while (delay--) { - for (i = 0; i < 100; i++) { - value = *pPORTFIO & PF5; - if (value != 0) { - break; - } - udelay(10000); - } - printf("\b\b\b%2d ", delay); - } - if (value != 0) - printf("\b\bOK"); - else { - result = -1; - printf("\b\bfailed"); - } - - delay = 5; - printf("\n--------Press SW11: %2d ", delay); - while (delay--) { - for (i = 0; i < 100; i++) { - value = *pPORTFIO & PF4; - if (value != 0) { - break; - } - udelay(10000); - } - printf("\b\b\b%2d ", delay); - } - if (value != 0) - printf("\b\bOK"); - else { - result = -1; - printf("\b\bfailed"); - } - - delay = 5; - printf("\n--------Press SW12: %2d ", delay); - while (delay--) { - for (i = 0; i < 100; i++) { - value = *pPORTFIO & PF3; - if (value != 0) { - break; - } - udelay(10000); - } - printf("\b\b\b%2d ", delay); - } - if (value != 0) - printf("\b\bOK"); - else { - result = -1; - printf("\b\bfailed"); - } - - delay = 5; - printf("\n--------Press SW13: %2d ", delay); - while (delay--) { - for (i = 0; i < 100; i++) { - value = *pPORTFIO & PF2; - if (value != 0) { - break; - } - udelay(10000); - } - printf("\b\b\b%2d ", delay); - } - if (value != 0) - printf("\b\bOK"); - else { - result = -1; - printf("\b\bfailed"); - } - printf("\n"); - return result; -} -#endif diff --git a/board/bf537-stamp/post-memory.c b/board/bf537-stamp/post-memory.c index 9626f4c..4daea62 100644 --- a/board/bf537-stamp/post-memory.c +++ b/board/bf537-stamp/post-memory.c @@ -1,8 +1,6 @@ #include <common.h> #include <asm/io.h> -#ifdef CONFIG_POST - #include <post.h> #include <watchdog.h> @@ -318,4 +316,3 @@ int post_init_sdram(int sclk) } #endif /* CONFIG_POST & CONFIG_SYS_POST_MEMORY */ -#endif /* CONFIG_POST */ diff --git a/board/bf537-stamp/post.c b/board/bf537-stamp/post.c new file mode 100644 index 0000000..4e844ba --- /dev/null +++ b/board/bf537-stamp/post.c @@ -0,0 +1,244 @@ +/* + * BF537-STAMP POST code + * + * Enter bugs at http://blackfin.uclinux.org/ + * + * Copyright (c) 2005-2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <common.h> +#include <config.h> +#include <command.h> +#include <asm/blackfin.h> + +#define POST_WORD_ADDR 0xFF903FFC + +/* Using sw10-PF5 as the hotkey */ +int post_hotkeys_pressed(void) +{ + int delay = 3; + int i; + unsigned short value; + + *pPORTF_FER &= ~PF5; + *pPORTFIO_DIR &= ~PF5; + *pPORTFIO_INEN |= PF5; + + printf("########Press SW10 to enter Memory POST########: %2d ", delay); + while (delay--) { + for (i = 0; i < 100; i++) { + value = *pPORTFIO & PF5; + if (value != 0) { + break; + } + udelay(10000); + } + printf("\b\b\b%2d ", delay); + } + printf("\b\b\b 0"); + printf("\n"); + if (value == 0) + return 0; + else { + printf("Hotkey has been pressed, Enter POST . . . . . .\n"); + return 1; + } +} + +void post_word_store(ulong a) +{ + volatile ulong *save_addr = (volatile ulong *)POST_WORD_ADDR; + *save_addr = a; +} + +ulong post_word_load(void) +{ + volatile ulong *save_addr = (volatile ulong *)POST_WORD_ADDR; + return *save_addr; +} + +int uart_post_test(int flags) +{ + return 0; +} + +#define BLOCK_SIZE 0x10000 +#define VERIFY_ADDR 0x2000000 +extern int erase_block_flash(int); +extern int write_data(long lStart, long lCount, uchar * pnData); +int flash_post_test(int flags) +{ + unsigned short *pbuf, *temp; + int offset, n, i; + int value = 0; + int result = 0; + printf("\n"); + pbuf = (unsigned short *)VERIFY_ADDR; + temp = pbuf; + for (n = FLASH_START_POST_BLOCK; n < FLASH_END_POST_BLOCK; n++) { + offset = (n - 7) * BLOCK_SIZE; + printf("--------Erase block:%2d..", n); + erase_block_flash(n); + printf("OK\r"); + printf("--------Program block:%2d...", n); + write_data(CONFIG_SYS_FLASH_BASE + offset, BLOCK_SIZE, pbuf); + printf("OK\r"); + printf("--------Verify block:%2d...", n); + for (i = 0; i < BLOCK_SIZE; i += 2) { + if (*(unsigned short *)(CONFIG_SYS_FLASH_BASE + offset + i) != + *temp++) { + value = 1; + result = 1; + } + } + if (value) + printf("failed\n"); + else + printf("OK %3d%%\r", + (int)( + (n + 1 - + FLASH_START_POST_BLOCK) * + 100 / (FLASH_END_POST_BLOCK - + FLASH_START_POST_BLOCK))); + + temp = pbuf; + value = 0; + } + printf("\n"); + if (result) + return -1; + else + return 0; +} + +/**************************************************** + * LED1 ---- PF6 LED2 ---- PF7 * + * LED3 ---- PF8 LED4 ---- PF9 * + * LED5 ---- PF10 LED6 ---- PF11 * + ****************************************************/ +int led_post_test(int flags) +{ + *pPORTF_FER &= ~(PF6 | PF7 | PF8 | PF9 | PF10 | PF11); + *pPORTFIO_DIR |= PF6 | PF7 | PF8 | PF9 | PF10 | PF11; + *pPORTFIO_INEN &= ~(PF6 | PF7 | PF8 | PF9 | PF10 | PF11); + *pPORTFIO &= ~(PF6 | PF7 | PF8 | PF9 | PF10 | PF11); + udelay(1000000); + printf("LED1 on"); + *pPORTFIO |= PF6; + udelay(1000000); + printf("\b\b\b\b\b\b\b"); + printf("LED2 on"); + *pPORTFIO |= PF7; + udelay(1000000); + printf("\b\b\b\b\b\b\b"); + printf("LED3 on"); + *pPORTFIO |= PF8; + udelay(1000000); + printf("\b\b\b\b\b\b\b"); + printf("LED4 on"); + *pPORTFIO |= PF9; + udelay(1000000); + printf("\b\b\b\b\b\b\b"); + printf("LED5 on"); + *pPORTFIO |= PF10; + udelay(1000000); + printf("\b\b\b\b\b\b\b"); + printf("lED6 on"); + *pPORTFIO |= PF11; + printf("\b\b\b\b\b\b\b "); + return 0; +} + +/************************************************ + * SW10 ---- PF5 SW11 ---- PF4 * + * SW12 ---- PF3 SW13 ---- PF2 * + ************************************************/ +int button_post_test(int flags) +{ + int i, delay = 5; + unsigned short value = 0; + int result = 0; + + *pPORTF_FER &= ~(PF5 | PF4 | PF3 | PF2); + *pPORTFIO_DIR &= ~(PF5 | PF4 | PF3 | PF2); + *pPORTFIO_INEN |= (PF5 | PF4 | PF3 | PF2); + + printf("\n--------Press SW10: %2d ", delay); + while (delay--) { + for (i = 0; i < 100; i++) { + value = *pPORTFIO & PF5; + if (value != 0) { + break; + } + udelay(10000); + } + printf("\b\b\b%2d ", delay); + } + if (value != 0) + printf("\b\bOK"); + else { + result = -1; + printf("\b\bfailed"); + } + + delay = 5; + printf("\n--------Press SW11: %2d ", delay); + while (delay--) { + for (i = 0; i < 100; i++) { + value = *pPORTFIO & PF4; + if (value != 0) { + break; + } + udelay(10000); + } + printf("\b\b\b%2d ", delay); + } + if (value != 0) + printf("\b\bOK"); + else { + result = -1; + printf("\b\bfailed"); + } + + delay = 5; + printf("\n--------Press SW12: %2d ", delay); + while (delay--) { + for (i = 0; i < 100; i++) { + value = *pPORTFIO & PF3; + if (value != 0) { + break; + } + udelay(10000); + } + printf("\b\b\b%2d ", delay); + } + if (value != 0) + printf("\b\bOK"); + else { + result = -1; + printf("\b\bfailed"); + } + + delay = 5; + printf("\n--------Press SW13: %2d ", delay); + while (delay--) { + for (i = 0; i < 100; i++) { + value = *pPORTFIO & PF2; + if (value != 0) { + break; + } + udelay(10000); + } + printf("\b\b\b%2d ", delay); + } + if (value != 0) + printf("\b\bOK"); + else { + result = -1; + printf("\b\bfailed"); + } + printf("\n"); + return result; +} diff --git a/board/bf537-stamp/spi_flash.c b/board/bf537-stamp/spi_flash.c index 7b764b4..7b753ad 100644 --- a/board/bf537-stamp/spi_flash.c +++ b/board/bf537-stamp/spi_flash.c @@ -18,6 +18,7 @@ #include <malloc.h> #include <asm/io.h> #include <asm/mach-common/bits/spi.h> +#include <asm/mach-common/bits/dma.h> /* Forcibly phase out these */ #ifdef CONFIG_SPI_FLASH_NUM_SECTORS @@ -32,53 +33,65 @@ struct flash_info { char *name; uint16_t id; + uint16_t ext_id; unsigned sector_size; unsigned num_sectors; }; /* SPI Speeds: 50 MHz / 33 MHz */ static struct flash_info flash_spansion_serial_flash[] = { - { "S25FL016", 0x0215, 64 * 1024, 32 }, - { "S25FL032", 0x0216, 64 * 1024, 64 }, - { "S25FL064", 0x0217, 64 * 1024, 128 }, - { "S25FL0128", 0x0218, 256 * 1024, 64 }, - { NULL, 0, 0, 0 } + { "S25FL016", 0x0215, 0, 64 * 1024, 32 }, + { "S25FL032", 0x0216, 0, 64 * 1024, 64 }, + { "S25FL064", 0x0217, 0, 64 * 1024, 128 }, + { "S25FL128-00", 0x2018, 0x0301, 64 * 1024, 256 }, /* Package marking FL128PIF */ + { "S25FL128-01", 0x2018, 0x0300, 128 * 1024, 64 }, /* Package marking FL128PIFL */ + { NULL, 0, 0, 0, 0 } }; /* SPI Speeds: 50 MHz / 20 MHz */ static struct flash_info flash_st_serial_flash[] = { - { "m25p05", 0x2010, 32 * 1024, 2 }, - { "m25p10", 0x2011, 32 * 1024, 4 }, - { "m25p20", 0x2012, 64 * 1024, 4 }, - { "m25p40", 0x2013, 64 * 1024, 8 }, - { "m25p16", 0x2015, 64 * 1024, 32 }, - { "m25p32", 0x2016, 64 * 1024, 64 }, - { "m25p64", 0x2017, 64 * 1024, 128 }, - { "m25p128", 0x2018, 256 * 1024, 64 }, - { NULL, 0, 0, 0 } + { "m25p05", 0x2010, 0, 32 * 1024, 2 }, + { "m25p10", 0x2011, 0, 32 * 1024, 4 }, + { "m25p20", 0x2012, 0, 64 * 1024, 4 }, + { "m25p40", 0x2013, 0, 64 * 1024, 8 }, + { "m25p80", 0x20FF, 0, 64 * 1024, 16 }, + { "m25p16", 0x2015, 0, 64 * 1024, 32 }, + { "m25p32", 0x2016, 0, 64 * 1024, 64 }, + { "m25p64", 0x2017, 0, 64 * 1024, 128 }, + { "m25p128", 0x2018, 0, 256 * 1024, 64 }, + { NULL, 0, 0, 0, 0 } +}; + +/* SPI Speeds: 20 MHz / 40 MHz */ +static struct flash_info flash_sst_serial_flash[] = { + { "SST25WF512", 0x2501, 0, 4 * 1024, 128 }, + { "SST25WF010", 0x2502, 0, 4 * 1024, 256 }, + { "SST25WF020", 0x2503, 0, 4 * 1024, 512 }, + { "SST25WF040", 0x2504, 0, 4 * 1024, 1024 }, + { NULL, 0, 0, 0, 0 } }; /* SPI Speeds: 66 MHz / 33 MHz */ static struct flash_info flash_atmel_dataflash[] = { - { "AT45DB011x", 0x0c, 264, 512 }, - { "AT45DB021x", 0x14, 264, 1025 }, - { "AT45DB041x", 0x1c, 264, 2048 }, - { "AT45DB081x", 0x24, 264, 4096 }, - { "AT45DB161x", 0x2c, 528, 4096 }, - { "AT45DB321x", 0x34, 528, 8192 }, - { "AT45DB642x", 0x3c, 1056, 8192 }, - { NULL, 0, 0, 0 } + { "AT45DB011x", 0x0c, 0, 264, 512 }, + { "AT45DB021x", 0x14, 0, 264, 1025 }, + { "AT45DB041x", 0x1c, 0, 264, 2048 }, + { "AT45DB081x", 0x24, 0, 264, 4096 }, + { "AT45DB161x", 0x2c, 0, 528, 4096 }, + { "AT45DB321x", 0x34, 0, 528, 8192 }, + { "AT45DB642x", 0x3c, 0, 1056, 8192 }, + { NULL, 0, 0, 0, 0 } }; /* SPI Speed: 50 MHz / 25 MHz or 40 MHz / 20 MHz */ static struct flash_info flash_winbond_serial_flash[] = { - { "W25X10", 0x3011, 16 * 256, 32 }, - { "W25X20", 0x3012, 16 * 256, 64 }, - { "W25X40", 0x3013, 16 * 256, 128 }, - { "W25X80", 0x3014, 16 * 256, 256 }, - { "W25P80", 0x2014, 256 * 256, 16 }, - { "W25P16", 0x2015, 256 * 256, 32 }, - { NULL, 0, 0, 0 } + { "W25X10", 0x3011, 0, 16 * 256, 32 }, + { "W25X20", 0x3012, 0, 16 * 256, 64 }, + { "W25X40", 0x3013, 0, 16 * 256, 128 }, + { "W25X80", 0x3014, 0, 16 * 256, 256 }, + { "W25P80", 0x2014, 0, 256 * 256, 16 }, + { "W25P16", 0x2015, 0, 256 * 256, 32 }, + { NULL, 0, 0, 0, 0 } }; struct flash_ops { @@ -97,6 +110,13 @@ static struct flash_ops flash_st_ops = { .status = 0x05, }; +static struct flash_ops flash_sst_ops = { + .read = OP_READ, + .write = 0x02, + .erase = 0x20, + .status = 0x05, +}; + static struct flash_ops flash_atmel_ops = { .read = OP_READ, .write = 0x82, @@ -122,7 +142,7 @@ static struct { struct manufacturer_info *manufacturer; struct flash_info *flash; struct flash_ops *ops; - uint8_t manufacturer_id, device_id1, device_id2; + uint8_t manufacturer_id, device_id1, device_id2, device_extid1, device_extid2; unsigned int write_length; unsigned long sector_size, num_sectors; } flash; @@ -130,6 +150,7 @@ static struct { enum { JED_MANU_SPANSION = 0x01, JED_MANU_ST = 0x20, + JED_MANU_SST = 0xBF, JED_MANU_ATMEL = 0x1F, JED_MANU_WINBOND = 0xEF, }; @@ -148,6 +169,12 @@ static struct manufacturer_info flash_manufacturers[] = { .ops = &flash_st_ops, }, { + .name = "SST", + .id = JED_MANU_SST, + .flashes = flash_sst_serial_flash, + .ops = &flash_sst_ops, + }, + { .name = "Atmel", .id = JED_MANU_ATMEL, .flashes = flash_atmel_dataflash, @@ -161,7 +188,7 @@ static struct manufacturer_info flash_manufacturers[] = { }, }; -#define TIMEOUT 5000 /* timeout of 5 seconds */ +#define TIMEOUT 5000 /* timeout of 5 seconds */ /* If part has multiple SPI flashes, assume SPI0 as that is * the one we can boot off of ... @@ -189,6 +216,7 @@ static void SPI_INIT(void) /* [#3541] This delay appears to be necessary, but not sure * exactly why as the history behind it is non-existant. */ + *pSPI_CTL = 0; udelay(CONFIG_CCLK_HZ / 25000000); /* enable SPI pins: SSEL, MOSI, MISO, SCK */ @@ -205,14 +233,13 @@ static void SPI_INIT(void) #endif /* initate communication upon write of TDBR */ - *pSPI_CTL = (SPE|MSTR|CPHA|CPOL|0x01); + *pSPI_CTL = (SPE | MSTR | CPHA | CPOL | TDBR_CORE); *pSPI_BAUD = CONFIG_SPI_BAUD; } static void SPI_DEINIT(void) { - /* put SPI settings back to reset state */ - *pSPI_CTL = 0x0400; + *pSPI_CTL = 0; *pSPI_BAUD = 0; SSYNC(); } @@ -275,6 +302,7 @@ static int wait_for_ready_status(void) switch (flash.manufacturer_id) { case JED_MANU_SPANSION: case JED_MANU_ST: + case JED_MANU_SST: case JED_MANU_WINBOND: if (!(read_status_register() & 0x01)) return 0; @@ -296,19 +324,68 @@ static int wait_for_ready_status(void) return -1; } +static int enable_writing(void) +{ + ulong start; + + if (flash.manufacturer_id == JED_MANU_ATMEL) + return 0; + + /* A write enable instruction must previously have been executed */ + SPI_ON(); + spi_write_read_byte(0x06); + SPI_OFF(); + + /* The status register will be polled to check the write enable latch "WREN" */ + start = get_timer(0); + while (get_timer(0) - start < TIMEOUT) { + if (read_status_register() & 0x02) + return 0; + + if (ctrlc()) { + puts("\nAbort\n"); + return -1; + } + } + + puts("Timeout\n"); + return -1; +} + +static void write_status_register(uint8_t val) +{ + if (flash.manufacturer_id != JED_MANU_SST) + hang(); + + if (enable_writing()) + return; + + /* send instruction to write status register */ + SPI_ON(); + spi_write_read_byte(0x01); + /* and clear it! */ + spi_write_read_byte(val); + SPI_OFF(); +} + /* Request and read the manufacturer and device id of parts which * are compatible with the JEDEC standard (JEP106) and use that to * setup other operating conditions. */ static int spi_detect_part(void) { - uint16_t dev_id; + uint16_t dev_id, dev_extid; size_t i; static char called_init; if (called_init) return 0; +#ifdef CONFIG_SPI_FLASH_M25P80 + flash.manufacturer_id = JED_MANU_ST; + flash.device_id1 = 0x20; + flash.device_id2 = 0xFF; +#else SPI_ON(); /* Send the request for the part identification */ @@ -327,9 +404,15 @@ static int spi_detect_part(void) /* Now read in the second device id byte */ flash.device_id2 = spi_write_read_byte(0); + /* Read extended device ids */ + flash.device_extid1 = spi_write_read_byte(0); + flash.device_extid2 = spi_write_read_byte(0); + SPI_OFF(); +#endif dev_id = (flash.device_id1 << 8) | flash.device_id2; + dev_extid = (flash.device_extid1 << 8) | flash.device_extid2; for (i = 0; i < ARRAY_SIZE(flash_manufacturers); ++i) { if (flash.manufacturer_id == flash_manufacturers[i].id) @@ -344,9 +427,12 @@ static int spi_detect_part(void) switch (flash.manufacturer_id) { case JED_MANU_SPANSION: case JED_MANU_ST: + case JED_MANU_SST: case JED_MANU_WINBOND: for (i = 0; flash.manufacturer->flashes[i].name; ++i) { - if (dev_id == flash.manufacturer->flashes[i].id) + if (dev_id == flash.manufacturer->flashes[i].id && + (flash.manufacturer->flashes[i].ext_id == 0 || + flash.manufacturer->flashes[i].ext_id == dev_extid)) break; } if (!flash.manufacturer->flashes[i].name) @@ -355,7 +441,11 @@ static int spi_detect_part(void) flash.flash = &flash.manufacturer->flashes[i]; flash.sector_size = flash.flash->sector_size; flash.num_sectors = flash.flash->num_sectors; - flash.write_length = 256; + + if (flash.manufacturer_id == JED_MANU_SST) + flash.write_length = 1; /* pwnt :( */ + else + flash.write_length = 256; break; case JED_MANU_ATMEL: { @@ -381,6 +471,10 @@ static int spi_detect_part(void) } } + /* the SST parts power up with software protection enabled by default */ + if (flash.manufacturer_id == JED_MANU_SST) + write_status_register(0); + called_init = 1; return 0; @@ -538,9 +632,10 @@ static void transmit_address(uint32_t addr) * int pnData - pointer to store value read from flash * long lCount - number of elements to read */ +#ifdef CONFIG_SPI_READFLASH_NODMA static int read_flash(unsigned long address, long count, uchar *buffer) { - size_t i; + size_t i, j; /* Send the read command to SPI device */ SPI_ON(); @@ -554,44 +649,134 @@ static int read_flash(unsigned long address, long count, uchar *buffer) /* After the SPI device address has been placed on the MOSI pin the data can be */ /* received on the MISO pin. */ + j = flash.sector_size << 1; for (i = 1; i <= count; ++i) { *buffer++ = spi_write_read_byte(0); - if (i % flash.sector_size == 0) + if (!j--) { puts("."); + j = flash.sector_size; + } } SPI_OFF(); return 0; } +#else -static int enable_writing(void) +#ifdef __ADSPBF54x__ +#define bfin_write_DMA_SPI_IRQ_STATUS bfin_write_DMA4_IRQ_STATUS +#define bfin_read_DMA_SPI_IRQ_STATUS bfin_read_DMA4_IRQ_STATUS +#define bfin_write_DMA_SPI_CURR_DESC_PTR bfin_write_DMA4_CURR_DESC_PTR +#define bfin_write_DMA_SPI_CONFIG bfin_write_DMA4_CONFIG +#elif defined(__ADSPBF533__) || defined(__ADSPBF532__) || defined(__ADSPBF531__) || \ + defined(__ADSPBF538__) || defined(__ADSPBF539__) +#define bfin_write_DMA_SPI_IRQ_STATUS bfin_write_DMA5_IRQ_STATUS +#define bfin_read_DMA_SPI_IRQ_STATUS bfin_read_DMA5_IRQ_STATUS +#define bfin_write_DMA_SPI_CURR_DESC_PTR bfin_write_DMA5_CURR_DESC_PTR +#define bfin_write_DMA_SPI_CONFIG bfin_write_DMA5_CONFIG +#elif defined(__ADSPBF561__) +#define bfin_write_DMA_SPI_IRQ_STATUS bfin_write_DMA16_IRQ_STATUS +#define bfin_read_DMA_SPI_IRQ_STATUS bfin_read_DMA16_IRQ_STATUS +#define bfin_write_DMA_SPI_CURR_DESC_PTR bfin_write_DMA16_CURR_DESC_PTR +#define bfin_write_DMA_SPI_CONFIG bfin_write_DMA16_CONFIG +#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) || \ + defined(__ADSPBF52x__) || defined(__ADSPBF51x__) +#define bfin_write_DMA_SPI_IRQ_STATUS bfin_write_DMA7_IRQ_STATUS +#define bfin_read_DMA_SPI_IRQ_STATUS bfin_read_DMA7_IRQ_STATUS +#define bfin_write_DMA_SPI_CURR_DESC_PTR bfin_write_DMA7_CURR_DESC_PTR +#define bfin_write_DMA_SPI_CONFIG bfin_write_DMA7_CONFIG +#else +#error "Please provide SPI DMA channel defines" +#endif + +struct dmadesc_array { + unsigned long start_addr; + unsigned short cfg; + unsigned short x_count; + short x_modify; + unsigned short y_count; + short y_modify; +} __attribute__((packed)); + +/* + * Read a value from flash for verify purpose + * Inputs: unsigned long ulStart - holds the SPI start address + * int pnData - pointer to store value read from flash + * long lCount - number of elements to read + */ + +static int read_flash(unsigned long address, long count, uchar *buffer) { - ulong start; + unsigned int ndsize; + struct dmadesc_array dma[2]; + /* Send the read command to SPI device */ - if (flash.manufacturer_id == JED_MANU_ATMEL) + if (!count) return 0; - /* A write enable instruction must previously have been executed */ + dma[0].start_addr = (unsigned long)buffer; + dma[0].x_modify = 1; + if (count <= 65536) { + blackfin_dcache_flush_invalidate_range(buffer, buffer + count); + ndsize = NDSIZE_5; + dma[0].cfg = NDSIZE_0 | WNR | WDSIZE_8 | FLOW_STOP | DMAEN | DI_EN; + dma[0].x_count = count; + } else { + blackfin_dcache_flush_invalidate_range(buffer, buffer + 65536 - 1); + ndsize = NDSIZE_7; + dma[0].cfg = NDSIZE_5 | WNR | WDSIZE_8 | FLOW_ARRAY | DMAEN | DMA2D; + dma[0].x_count = 0; /* 2^16 */ + dma[0].y_count = count >> 16; /* count / 2^16 */ + dma[0].y_modify = 1; + dma[1].start_addr = (unsigned long)(buffer + (count & ~0xFFFF)); + dma[1].cfg = NDSIZE_0 | WNR | WDSIZE_8 | FLOW_STOP | DMAEN | DI_EN; + dma[1].x_count = count & 0xFFFF; /* count % 2^16 */ + dma[1].x_modify = 1; + } + + bfin_write_DMA_SPI_CONFIG(0); + bfin_write_DMA_SPI_IRQ_STATUS(DMA_DONE | DMA_ERR); + bfin_write_DMA_SPI_CURR_DESC_PTR(dma); + SPI_ON(); - spi_write_read_byte(0x06); + + spi_write_read_byte(flash.ops->read); + transmit_address(address); + +#ifndef CONFIG_SPI_FLASH_SLOW_READ + /* Send dummy byte when doing SPI fast reads */ + spi_write_read_byte(0); +#endif + + bfin_write_DMA_SPI_CONFIG(ndsize | FLOW_ARRAY | DMAEN); + *pSPI_CTL = (MSTR | CPHA | CPOL | RDBR_DMA | SPE | SZ); + SSYNC(); + + /* + * We already invalidated the first 64k, + * now while we just wait invalidate the remaining part. + * Its not likely that the DMA is going to overtake + */ + if (count > 65536) + blackfin_dcache_flush_invalidate_range(buffer + 65536, + buffer + count); + + while (!(bfin_read_DMA_SPI_IRQ_STATUS() & DMA_DONE)) + if (ctrlc()) + break; + SPI_OFF(); - /* The status register will be polled to check the write enable latch "WREN" */ - start = get_timer(0); - while (get_timer(0) - start < TIMEOUT) { - if (read_status_register() & 0x02) - return 0; + *pSPI_CTL = 0; - if (ctrlc()) { - puts("\nAbort\n"); - return -1; - } - } + bfin_write_DMA_SPI_CONFIG(0); - puts("Timeout\n"); - return -1; + *pSPI_CTL = (SPE | MSTR | CPHA | CPOL | TDBR_CORE); + + return 0; } +#endif static long address_to_sector(unsigned long address) { diff --git a/board/bf537-stamp/u-boot.lds.S b/board/bf537-stamp/u-boot.lds.S index 76daa75..8ddfa81 100644 --- a/board/bf537-stamp/u-boot.lds.S +++ b/board/bf537-stamp/u-boot.lds.S @@ -44,12 +44,11 @@ OUTPUT_ARCH(bfin) -/* The 0xC offset is so we don't clobber the tiny LDR jump block. */ MEMORY { ram : ORIGIN = CONFIG_SYS_MONITOR_BASE, LENGTH = CONFIG_SYS_MONITOR_LEN - l1_code : ORIGIN = L1_INST_SRAM+0xC, LENGTH = L1_INST_SRAM_SIZE - l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE + l1_code : ORIGIN = L1_INST_SRAM, LENGTH = L1_INST_SRAM_SIZE + l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE } ENTRY(_start) diff --git a/board/bf561-ezkit/u-boot.lds.S b/board/bf561-ezkit/u-boot.lds.S index 3d0453e..4220e81 100644 --- a/board/bf561-ezkit/u-boot.lds.S +++ b/board/bf561-ezkit/u-boot.lds.S @@ -44,12 +44,11 @@ OUTPUT_ARCH(bfin) -/* The 0xC offset is so we don't clobber the tiny LDR jump block. */ MEMORY { ram : ORIGIN = CONFIG_SYS_MONITOR_BASE, LENGTH = CONFIG_SYS_MONITOR_LEN - l1_code : ORIGIN = L1_INST_SRAM+0xC, LENGTH = L1_INST_SRAM_SIZE - l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE + l1_code : ORIGIN = L1_INST_SRAM, LENGTH = L1_INST_SRAM_SIZE + l1_data : ORIGIN = L1_DATA_B_SRAM, LENGTH = L1_DATA_B_SRAM_SIZE } ENTRY(_start) diff --git a/cpu/blackfin/cpu.c b/cpu/blackfin/cpu.c index 30c214b..c2ff8cd 100644 --- a/cpu/blackfin/cpu.c +++ b/cpu/blackfin/cpu.c @@ -25,18 +25,12 @@ ulong bfin_poweron_retx; __attribute__ ((__noreturn__)) void cpu_init_f(ulong bootflag, ulong loaded_from_ldr) { - /* Build a NOP slide over the LDR jump block. Whee! */ - serial_early_puts("NOP Slide\n"); - char nops[0xC]; - memset(nops, 0x00, sizeof(nops)); - extern char _stext_l1; - memcpy(&_stext_l1 - sizeof(nops), nops, sizeof(nops)); - if (!loaded_from_ldr) { /* Relocate sections into L1 if the LDR didn't do it -- don't * check length because the linker script does the size * checking at build time. */ + extern char _stext_l1; serial_early_puts("L1 Relocate\n"); extern char _stext_l1, _etext_l1, _stext_l1_lma; memcpy(&_stext_l1, &_stext_l1_lma, (&_etext_l1 - &_stext_l1)); diff --git a/cpu/blackfin/initcode.c b/cpu/blackfin/initcode.c index 3f3b479..7bd4b22 100644 --- a/cpu/blackfin/initcode.c +++ b/cpu/blackfin/initcode.c @@ -12,6 +12,7 @@ #include <config.h> #include <asm/blackfin.h> #include <asm/mach-common/bits/bootrom.h> +#include <asm/mach-common/bits/core.h> #include <asm/mach-common/bits/ebiu.h> #include <asm/mach-common/bits/pll.h> #include <asm/mach-common/bits/uart.h> @@ -203,6 +204,48 @@ static inline void serial_putc(char c) # define CONFIG_VR_CTL_VAL (CONFIG_VR_CTL_CLKBUF | CONFIG_VR_CTL_VLEV | CONFIG_VR_CTL_FREQ) #endif +/* some parts do not have an on-chip voltage regulator */ +#if defined(__ADSPBF51x__) +# define CONFIG_HAS_VR 0 +# undef CONFIG_VR_CTL_VAL +# define CONFIG_VR_CTL_VAL 0 +#else +# define CONFIG_HAS_VR 1 +#endif + +#ifndef EBIU_RSTCTL +/* Blackfin with SDRAM */ +#ifndef CONFIG_EBIU_SDBCTL_VAL +# if CONFIG_MEM_SIZE == 16 +# define CONFIG_EBSZ_VAL EBSZ_16 +# elif CONFIG_MEM_SIZE == 32 +# define CONFIG_EBSZ_VAL EBSZ_32 +# elif CONFIG_MEM_SIZE == 64 +# define CONFIG_EBSZ_VAL EBSZ_64 +# elif CONFIG_MEM_SIZE == 128 +# define CONFIG_EBSZ_VAL EBSZ_128 +# elif CONFIG_MEM_SIZE == 256 +# define CONFIG_EBSZ_VAL EBSZ_256 +# elif CONFIG_MEM_SIZE == 512 +# define CONFIG_EBSZ_VAL EBSZ_512 +# else +# error You need to define CONFIG_EBIU_SDBCTL_VAL or CONFIG_MEM_SIZE +# endif +# if CONFIG_MEM_ADD_WDTH == 8 +# define CONFIG_EBCAW_VAL EBCAW_8 +# elif CONFIG_MEM_ADD_WDTH == 9 +# define CONFIG_EBCAW_VAL EBCAW_9 +# elif CONFIG_MEM_ADD_WDTH == 10 +# define CONFIG_EBCAW_VAL EBCAW_10 +# elif CONFIG_MEM_ADD_WDTH == 11 +# define CONFIG_EBCAW_VAL EBCAW_11 +# else +# error You need to define CONFIG_EBIU_SDBCTL_VAL or CONFIG_MEM_ADD_WDTH +# endif +# define CONFIG_EBIU_SDBCTL_VAL (CONFIG_EBCAW_VAL | CONFIG_EBSZ_VAL | EBE) +#endif +#endif + BOOTROM_CALLED_FUNC_ATTR void initcode(ADI_BOOT_DATA *bootstruct) { @@ -215,6 +258,8 @@ void initcode(ADI_BOOT_DATA *bootstruct) divB = serial_early_get_div(); } + serial_putc('A'); + #ifdef CONFIG_HW_WATCHDOG # ifndef CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE # define CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE 20000 @@ -231,7 +276,23 @@ void initcode(ADI_BOOT_DATA *bootstruct) } #endif - serial_putc('S'); + serial_putc('B'); + + /* If external memory is enabled, put it into self refresh first. */ + bool put_into_srfs = false; +#ifdef EBIU_RSTCTL + if (bfin_read_EBIU_RSTCTL() & DDR_SRESET) { + bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() | SRREQ); + put_into_srfs = true; + } +#else + if (bfin_read_EBIU_SDBCTL() & EBE) { + bfin_write_EBIU_SDGCTL(bfin_read_EBIU_SDGCTL() | SRFS); + put_into_srfs = true; + } +#endif + + serial_putc('C'); /* Blackfin bootroms use the SPI slow read opcode instead of the SPI * fast read, so we need to slow down the SPI clock a lot more during @@ -244,54 +305,81 @@ void initcode(ADI_BOOT_DATA *bootstruct) bfin_write_SPI_BAUD(CONFIG_SPI_BAUD_INITBLOCK); } - serial_putc('B'); + serial_putc('D'); - /* Disable all peripheral wakeups except for the PLL event. */ -#ifdef SIC_IWR0 - bfin_write_SIC_IWR0(1); - bfin_write_SIC_IWR1(0); -# ifdef SIC_IWR2 - bfin_write_SIC_IWR2(0); -# endif -#elif defined(SICA_IWR0) - bfin_write_SICA_IWR0(1); - bfin_write_SICA_IWR1(0); + /* If we're entering self refresh, make sure it has happened. */ + if (put_into_srfs) +#ifdef EBIU_RSTCTL + while (!(bfin_read_EBIU_RSTCTL() & SRACK)) #else - bfin_write_SIC_IWR(1); + while (!(bfin_read_EBIU_SDSTAT() & SDSRA)) #endif + continue; + + serial_putc('E'); /* With newer bootroms, we use the helper function to set up * the memory controller. Older bootroms lacks such helpers * so we do it ourselves. */ -#define BOOTROM_CAPS_SYSCONTROL 0 - if (BOOTROM_CAPS_SYSCONTROL) { - serial_putc('S'); + uint16_t vr_ctl = bfin_read_VR_CTL(); + if (!ANOMALY_05000386) { + serial_putc('F'); ADI_SYSCTRL_VALUES memory_settings; - memory_settings.uwVrCtl = CONFIG_VR_CTL_VAL; + uint32_t actions = SYSCTRL_WRITE | SYSCTRL_PLLCTL | SYSCTRL_PLLDIV | SYSCTRL_LOCKCNT; + if (CONFIG_HAS_VR) { + actions |= SYSCTRL_VRCTL; + if (CONFIG_VR_CTL_VAL & FREQ_MASK) + actions |= SYSCTRL_INTVOLTAGE; + else + actions |= SYSCTRL_EXTVOLTAGE; + memory_settings.uwVrCtl = CONFIG_VR_CTL_VAL; + } else + actions |= SYSCTRL_EXTVOLTAGE; memory_settings.uwPllCtl = CONFIG_PLL_CTL_VAL; memory_settings.uwPllDiv = CONFIG_PLL_DIV_VAL; memory_settings.uwPllLockCnt = CONFIG_PLL_LOCKCNT_VAL; - syscontrol(SYSCTRL_WRITE | SYSCTRL_VRCTL | SYSCTRL_PLLCTL | SYSCTRL_PLLDIV | SYSCTRL_LOCKCNT | - (CONFIG_VR_CTL_VAL & FREQ_MASK ? SYSCTRL_INTVOLTAGE : SYSCTRL_EXTVOLTAGE), &memory_settings, NULL); +#if ANOMALY_05000432 + bfin_write_SIC_IWR1(0); +#endif + bfrom_SysControl(actions, &memory_settings, NULL); +#if ANOMALY_05000432 + bfin_write_SIC_IWR1(-1); +#endif } else { - serial_putc('L'); + serial_putc('G'); + + /* Disable all peripheral wakeups except for the PLL event. */ +#ifdef SIC_IWR0 + bfin_write_SIC_IWR0(1); + bfin_write_SIC_IWR1(0); +# ifdef SIC_IWR2 + bfin_write_SIC_IWR2(0); +# endif +#elif defined(SICA_IWR0) + bfin_write_SICA_IWR0(1); + bfin_write_SICA_IWR1(0); +#else + bfin_write_SIC_IWR(1); +#endif + + serial_putc('H'); bfin_write_PLL_LOCKCNT(CONFIG_PLL_LOCKCNT_VAL); - serial_putc('A'); + serial_putc('I'); /* Only reprogram when needed to avoid triggering unnecessary * PLL relock sequences. */ - if (bfin_read_VR_CTL() != CONFIG_VR_CTL_VAL) { + if (vr_ctl != CONFIG_VR_CTL_VAL) { serial_putc('!'); bfin_write_VR_CTL(CONFIG_VR_CTL_VAL); asm("idle;"); } - serial_putc('C'); + serial_putc('J'); bfin_write_PLL_DIV(CONFIG_PLL_DIV_VAL); @@ -305,8 +393,26 @@ void initcode(ADI_BOOT_DATA *bootstruct) bfin_write_PLL_CTL(CONFIG_PLL_CTL_VAL); asm("idle;"); } + + serial_putc('L'); + + /* Restore all peripheral wakeups. */ +#ifdef SIC_IWR0 + bfin_write_SIC_IWR0(-1); + bfin_write_SIC_IWR1(-1); +# ifdef SIC_IWR2 + bfin_write_SIC_IWR2(-1); +# endif +#elif defined(SICA_IWR0) + bfin_write_SICA_IWR0(-1); + bfin_write_SICA_IWR1(-1); +#else + bfin_write_SIC_IWR(-1); +#endif } + serial_putc('M'); + /* Since we've changed the SCLK above, we may need to update * the UART divisors (UART baud rates are based on SCLK). * Do the division by hand as there are no native instructions @@ -324,23 +430,32 @@ void initcode(ADI_BOOT_DATA *bootstruct) serial_early_put_div(quotient - ANOMALY_05000230); } - serial_putc('F'); + serial_putc('N'); - /* Program the async banks controller. */ - bfin_write_EBIU_AMBCTL0(CONFIG_EBIU_AMBCTL0_VAL); - bfin_write_EBIU_AMBCTL1(CONFIG_EBIU_AMBCTL1_VAL); - bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL); + /* Program the external memory controller before we come out of + * self-refresh. This only works with our SDRAM controller. + */ +#ifndef EBIU_RSTCTL + bfin_write_EBIU_SDRRC(CONFIG_EBIU_SDRRC_VAL); + bfin_write_EBIU_SDBCTL(CONFIG_EBIU_SDBCTL_VAL); + bfin_write_EBIU_SDGCTL(CONFIG_EBIU_SDGCTL_VAL); +#endif -#ifdef EBIU_MODE - /* Not all parts have these additional MMRs. */ - bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTL_VAL); - bfin_write_EBIU_MODE(CONFIG_EBIU_MODE_VAL); - bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTL_VAL); + serial_putc('O'); + + /* Now that we've reprogrammed, take things out of self refresh. */ + if (put_into_srfs) +#ifdef EBIU_RSTCTL + bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() & ~(SRREQ)); +#else + bfin_write_EBIU_SDGCTL(bfin_read_EBIU_SDGCTL() & ~(SRFS)); #endif - serial_putc('I'); + serial_putc('P'); - /* Program the external memory controller. */ + /* Our DDR controller sucks and cannot be programmed while in + * self-refresh. So we have to pull it out before programming. + */ #ifdef EBIU_RSTCTL bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() | 0x1 /*DDRSRESET*/ | CONFIG_EBIU_RSTCTL_VAL); bfin_write_EBIU_DDRCTL0(CONFIG_EBIU_DDRCTL0_VAL); @@ -350,28 +465,64 @@ void initcode(ADI_BOOT_DATA *bootstruct) /* default is disable, so don't need to force this */ bfin_write_EBIU_DDRCTL3(CONFIG_EBIU_DDRCTL3_VAL); # endif -#else - bfin_write_EBIU_SDRRC(CONFIG_EBIU_SDRRC_VAL); - bfin_write_EBIU_SDBCTL(CONFIG_EBIU_SDBCTL_VAL); - bfin_write_EBIU_SDGCTL(CONFIG_EBIU_SDGCTL_VAL); +# ifdef CONFIG_EBIU_DDRQUE_VAL + bfin_write_EBIU_DDRQUE(bfin_read_EBIU_DDRQUE() | CONFIG_EBIU_DDRQUE_VAL); +# endif #endif - serial_putc('N'); + serial_putc('Q'); - /* Restore all peripheral wakeups. */ -#ifdef SIC_IWR0 - bfin_write_SIC_IWR0(-1); - bfin_write_SIC_IWR1(-1); -# ifdef SIC_IWR2 - bfin_write_SIC_IWR2(-1); -# endif -#elif defined(SICA_IWR0) - bfin_write_SICA_IWR0(-1); - bfin_write_SICA_IWR1(-1); -#else - bfin_write_SIC_IWR(-1); + /* Are we coming out of hibernate (suspend to memory) ? + * The memory layout is: + * 0x0: hibernate magic for anomaly 307 (0xDEADBEEF) + * 0x4: return address + * 0x8: stack pointer + * + * SCKELOW is unreliable on older parts (anomaly 307) + */ + if (ANOMALY_05000307 || vr_ctl & 0x8000) { + uint32_t *hibernate_magic = 0; + __builtin_bfin_ssync(); /* make sure memory controller is done */ + if (hibernate_magic[0] == 0xDEADBEEF) { + serial_putc('R'); + bfin_write_EVT15(hibernate_magic[1]); + bfin_write_IMASK(EVT_IVG15); + __asm__ __volatile__ ( + /* load reti early to avoid anomaly 281 */ + "reti = %0;" + /* clear hibernate magic */ + "[%0] = %1;" + /* load stack pointer */ + "SP = [%0 + 8];" + /* lower ourselves from reset ivg to ivg15 */ + "raise 15;" + "rti;" + : + : "p"(hibernate_magic), "d"(0x2000 /* jump.s 0 */) + ); + } + } + + serial_putc('S'); + + /* Program the async banks controller. */ + bfin_write_EBIU_AMBCTL0(CONFIG_EBIU_AMBCTL0_VAL); + bfin_write_EBIU_AMBCTL1(CONFIG_EBIU_AMBCTL1_VAL); + bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL); + +#ifdef EBIU_MODE + /* Not all parts have these additional MMRs. */ + bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTL_VAL); + bfin_write_EBIU_MODE(CONFIG_EBIU_MODE_VAL); + bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTL_VAL); #endif + serial_putc('T'); + + /* tell the bootrom where our entry point is */ + if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) + bfin_write_EVT1(CONFIG_SYS_MONITOR_BASE); + serial_putc('>'); serial_putc('\n'); diff --git a/cpu/blackfin/jtag-console.c b/cpu/blackfin/jtag-console.c index 44c0a83..d58582f 100644 --- a/cpu/blackfin/jtag-console.c +++ b/cpu/blackfin/jtag-console.c @@ -54,16 +54,23 @@ static void jtag_puts(const char *s) jtag_send(s, strlen(s)); } -static int jtag_tstc(void) +static size_t inbound_len, leftovers_len; + +/* Lower layers want to know when jtag has data */ +static int jtag_tstc_dbg(void) { return (bfin_read_DBGSTAT() & 0x2); } +/* Higher layers want to know when any data is available */ +static int jtag_tstc(void) +{ + return jtag_tstc_dbg() || leftovers_len; +} + /* Receive a buffer. The format is: * [32bit length][actual data] */ -static size_t inbound_len; -static int leftovers_len; static uint32_t leftovers; static int jtag_getc(void) { @@ -79,7 +86,7 @@ static int jtag_getc(void) } /* wait for new data ! */ - while (!jtag_tstc()) + while (!jtag_tstc_dbg()) continue; __asm__("%0 = emudat;" : "=d"(emudat)); diff --git a/cpu/blackfin/reset.c b/cpu/blackfin/reset.c index 284cea5..e3be740 100644 --- a/cpu/blackfin/reset.c +++ b/cpu/blackfin/reset.c @@ -20,7 +20,7 @@ * the core reset. */ __attribute__ ((__l1_text__, __noreturn__)) -void bfin_reset(void) +static void bfin_reset(void) { /* Wait for completion of "system" events such as cache line * line fills so that we avoid infinite stalls later on as diff --git a/cpu/blackfin/start.S b/cpu/blackfin/start.S index 6c8def4..506fea5 100644 --- a/cpu/blackfin/start.S +++ b/cpu/blackfin/start.S @@ -95,36 +95,64 @@ ENTRY(_start) /* Save RETX so we can pass it while booting Linux */ r7 = RETX; -#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) - /* In bypass mode, we don't have an LDR with an init block - * so we need to explicitly call it ourselves. This will - * reprogram our clocks and setup our async banks. - */ - /* XXX: we should DMA this into L1, put external memory into - * self refresh, and then jump there ... + /* Figure out where we are currently executing so that we can decide + * how to best reprogram and relocate things. We'll pass below: + * R4: load address of _start + * R5: current (not load) address of _start */ + serial_early_puts("Find ourselves"); + call _get_pc; - r3 = 0x0; - r3.h = 0x2000; - cc = r0 < r3 (iu); - if cc jump .Lproc_initialized; +.Loffset: + r1.l = .Loffset; + r1.h = .Loffset; + r4.l = _start; + r4.h = _start; + r3 = r1 - r4; + r5 = r0 - r3; + + /* Inform upper layers if we had to do the relocation ourselves. + * This allows us to detect whether we were loaded by 'go 0x1000' + * or by the bootrom from an LDR. "R6" is "loaded_from_ldr". + */ + r6 = 1 (x); + cc = r4 == r5; + if cc jump .Lnorelocate; + r6 = 0 (x); + /* In bypass mode, we don't have an LDR with an init block + * so we need to explicitly call it ourselves. This will + * reprogram our clocks, memory, and setup our async banks. + */ serial_early_puts("Program Clocks"); + /* if we're executing >=0x20000000, then we dont need to dma */ + r3 = 0x0; + r3.h = 0x2000; + cc = r5 < r3 (iu); + if cc jump .Ldma_and_reprogram; call _initcode; + jump .Lprogrammed; + + /* we're sitting in external memory, so dma into L1 and reprogram */ +.Ldma_and_reprogram: + r0.l = LO(L1_INST_SRAM); + r0.h = HI(L1_INST_SRAM); + r1.l = __initcode_start; + r1.h = __initcode_start; + r2.l = __initcode_end; + r2.h = __initcode_end; + r2 = r2 - r1; /* convert r2 into length of initcode */ + r1 = r1 - r4; /* convert r1 from load address of initcode ... */ + r1 = r1 + r5; /* ... to current (not load) address of initcode */ + p3 = r0; + call _dma_memcpy_nocache; + call (p3); /* Since we reprogrammed SCLK, we need to update the serial divisor */ +.Lprogrammed: serial_early_set_baud -.Lproc_initialized: -#endif - - /* Inform upper layers if we had to do the relocation ourselves. - * This allows us to detect whether we were loaded by 'go 0x1000' - * or by the bootrom from an LDR. "r6" is "loaded_from_ldr". - */ - r6 = 1 (x); - /* Relocate from wherever we are (FLASH/RAM/etc...) to the hardcoded * monitor location in the end of RAM. We know that memcpy() only * uses registers, so it is safe to call here. Note that this only @@ -132,19 +160,8 @@ ENTRY(_start) * it yet (see "lower to 15" below). */ serial_early_puts("Relocate"); - call _get_pc; -.Loffset: - r2.l = .Loffset; - r2.h = .Loffset; - r3.l = _start; - r3.h = _start; - r2 = r2 - r3; - r1 = r0 - r2; - cc = r1 == r3; - if cc jump .Lnorelocate; - r6 = 0 (x); - - r0 = r3; + r0 = r4; + r1 = r5; r2.l = LO(CONFIG_SYS_MONITOR_LEN); r2.h = HI(CONFIG_SYS_MONITOR_LEN); call _memcpy_ASM; diff --git a/cpu/blackfin/traps.c b/cpu/blackfin/traps.c index a2c6f1e..2121b0e 100644 --- a/cpu/blackfin/traps.c +++ b/cpu/blackfin/traps.c @@ -193,7 +193,7 @@ static const char *symbol_lookup(unsigned long addr, unsigned long *caddr) while (*sym) { sym_addr = simple_strtoul(sym, &esym, 16); - sym = esym + 1; + sym = esym; if (sym_addr > addr) break; *caddr = sym_addr; diff --git a/drivers/spi/bfin_spi.c b/drivers/spi/bfin_spi.c index d22862a..0472c1a 100644 --- a/drivers/spi/bfin_spi.c +++ b/drivers/spi/bfin_spi.c @@ -191,21 +191,19 @@ static void spi_portmux(struct spi_slave *slave) #elif defined(__ADSPBF534__) || defined(__ADSPBF536__) || defined(__ADSPBF537__) u16 mux = bfin_read_PORT_MUX(); u16 f_fer = bfin_read_PORTF_FER(); - u16 j_fer = bfin_read_PORTJ_FER(); /* set SCK/MISO/MOSI */ f_fer |= PF11 | PF12 | PF13; switch (slave->cs) { case 1: f_fer |= PF10; break; - case 2: mux |= PJSE; j_fer |= PJ11; break; - case 3: mux |= PJSE; j_fer |= PJ10; break; + case 2: mux |= PJSE; break; + case 3: mux |= PJSE; break; case 4: mux |= PFS4E; f_fer |= PF6; break; case 5: mux |= PFS5E; f_fer |= PF5; break; case 6: mux |= PFS6E; f_fer |= PF4; break; - case 7: mux |= PJCE_SPI; j_fer |= PJ5; break; + case 7: mux |= PJCE_SPI; break; } bfin_write_PORT_MUX(mux); bfin_write_PORTF_FER(f_fer); - bfin_write_PORTJ_FER(j_fer); #elif defined(__ADSPBF54x__) #define DO_MUX(port, pin) \ mux = ((mux & ~PORT_x_MUX_##pin##_MASK) | PORT_x_MUX_##pin##_FUNC_1); \ diff --git a/include/asm-blackfin/blackfin-config-pre.h b/include/asm-blackfin/blackfin-config-pre.h index 9df01ad..e973de7 100644 --- a/include/asm-blackfin/blackfin-config-pre.h +++ b/include/asm-blackfin/blackfin-config-pre.h @@ -14,12 +14,6 @@ #define MK_STR(x) XMK_STR(x) #define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0])) -/* Configurable Blackfin-specific monitor commands */ -#define CONFIG_SYS_BFIN_CMD_BOOTLDR 0x01 -#define CONFIG_SYS_BFIN_CMD_CPLBINFO 0x02 -#define CONFIG_SYS_BFIN_CMD_OTP 0x04 -#define CONFIG_SYS_BFIN_CMD_CACHE_DUMP 0x08 - /* Bootmode defines -- your config needs to select this via CONFIG_BFIN_BOOT_MODE. * Depending on your cpu, some of these may not be valid, check your HRM. * The actual values here are meaningless as long as they're unique. diff --git a/include/asm-blackfin/mach-bf527/ADSP-EDN-BF52x-extended_cdef.h b/include/asm-blackfin/mach-bf527/ADSP-EDN-BF52x-extended_cdef.h index 85acdd6..f65b439 100644 --- a/include/asm-blackfin/mach-bf527/ADSP-EDN-BF52x-extended_cdef.h +++ b/include/asm-blackfin/mach-bf527/ADSP-EDN-BF52x-extended_cdef.h @@ -6,9 +6,9 @@ #ifndef __BFIN_CDEF_ADSP_EDN_BF52x_extended__ #define __BFIN_CDEF_ADSP_EDN_BF52x_extended__ -#define pSIC_RVECT ((uint32_t volatile *)SIC_RVECT) /* Interrupt Reset Vector Address Register */ -#define bfin_read_SIC_RVECT() bfin_read32(SIC_RVECT) -#define bfin_write_SIC_RVECT(val) bfin_write32(SIC_RVECT, val) +#define pSIC_RVECT ((uint16_t volatile *)SIC_RVECT) /* Interrupt Reset Vector Address Register */ +#define bfin_read_SIC_RVECT() bfin_read16(SIC_RVECT) +#define bfin_write_SIC_RVECT(val) bfin_write16(SIC_RVECT, val) #define pSIC_IMASK0 ((uint32_t volatile *)SIC_IMASK0) /* Interrupt Mask Register */ #define bfin_read_SIC_IMASK0() bfin_read32(SIC_IMASK0) #define bfin_write_SIC_IMASK0(val) bfin_write32(SIC_IMASK0, val) @@ -304,7 +304,6 @@ #define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV) #define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV, val) #define pSPORT0_TX ((uint32_t volatile *)SPORT0_TX) /* SPORT0 TX Data Register */ -#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) #define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) #define pSPORT0_RX ((uint32_t volatile *)SPORT0_RX) /* SPORT0 RX Data Register */ #define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX) @@ -370,7 +369,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 TX Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RX ((uint32_t volatile *)SPORT1_RX) /* SPORT1 RX Data Register */ #define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX) diff --git a/include/asm-blackfin/mach-bf527/anomaly.h b/include/asm-blackfin/mach-bf527/anomaly.h index 035e8d8..df6808d 100644 --- a/include/asm-blackfin/mach-bf527/anomaly.h +++ b/include/asm-blackfin/mach-bf527/anomaly.h @@ -2,7 +2,7 @@ * File: include/asm-blackfin/mach-bf527/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2008 Analog Devices Inc. + * Copyright (C) 2004-2009 Analog Devices Inc. * Licensed under the GPL-2 or later. */ @@ -167,12 +167,16 @@ #define ANOMALY_05000263 (0) #define ANOMALY_05000266 (0) #define ANOMALY_05000273 (0) +#define ANOMALY_05000278 (0) #define ANOMALY_05000285 (0) +#define ANOMALY_05000305 (0) #define ANOMALY_05000307 (0) #define ANOMALY_05000311 (0) #define ANOMALY_05000312 (0) #define ANOMALY_05000323 (0) #define ANOMALY_05000363 (0) #define ANOMALY_05000412 (0) +#define ANOMALY_05000447 (0) +#define ANOMALY_05000448 (0) #endif diff --git a/include/asm-blackfin/mach-bf527/ports.h b/include/asm-blackfin/mach-bf527/ports.h index c32d69f..e6b1df8 100644 --- a/include/asm-blackfin/mach-bf527/ports.h +++ b/include/asm-blackfin/mach-bf527/ports.h @@ -52,76 +52,9 @@ #define PORT_x_MUX_7_FUNC_3 (PORT_x_MUX_FUNC_3 << 14) #define PORT_x_MUX_7_FUNC_4 (PORT_x_MUX_FUNC_4 << 14) -/* Port F Masks */ -#define PF0 0x0001 -#define PF1 0x0002 -#define PF2 0x0004 -#define PF3 0x0008 -#define PF4 0x0010 -#define PF5 0x0020 -#define PF6 0x0040 -#define PF7 0x0080 -#define PF8 0x0100 -#define PF9 0x0200 -#define PF10 0x0400 -#define PF11 0x0800 -#define PF12 0x1000 -#define PF13 0x2000 -#define PF14 0x4000 -#define PF15 0x8000 - -/* Port G Masks */ -#define PG0 0x0001 -#define PG1 0x0002 -#define PG2 0x0004 -#define PG3 0x0008 -#define PG4 0x0010 -#define PG5 0x0020 -#define PG6 0x0040 -#define PG7 0x0080 -#define PG8 0x0100 -#define PG9 0x0200 -#define PG10 0x0400 -#define PG11 0x0800 -#define PG12 0x1000 -#define PG13 0x2000 -#define PG14 0x4000 -#define PG15 0x8000 - -/* Port H Masks */ -#define PH0 0x0001 -#define PH1 0x0002 -#define PH2 0x0004 -#define PH3 0x0008 -#define PH4 0x0010 -#define PH5 0x0020 -#define PH6 0x0040 -#define PH7 0x0080 -#define PH8 0x0100 -#define PH9 0x0200 -#define PH10 0x0400 -#define PH11 0x0800 -#define PH12 0x1000 -#define PH13 0x2000 -#define PH14 0x4000 -#define PH15 0x8000 - -/* Port J Masks */ -#define PJ0 0x0001 -#define PJ1 0x0002 -#define PJ2 0x0004 -#define PJ3 0x0008 -#define PJ4 0x0010 -#define PJ5 0x0020 -#define PJ6 0x0040 -#define PJ7 0x0080 -#define PJ8 0x0100 -#define PJ9 0x0200 -#define PJ10 0x0400 -#define PJ11 0x0800 -#define PJ12 0x1000 -#define PJ13 0x2000 -#define PJ14 0x4000 -#define PJ15 0x8000 +#include "../mach-common/bits/ports-f.h" +#include "../mach-common/bits/ports-g.h" +#include "../mach-common/bits/ports-h.h" +#include "../mach-common/bits/ports-j.h" #endif diff --git a/include/asm-blackfin/mach-bf533/anomaly.h b/include/asm-blackfin/mach-bf533/anomaly.h index 0d3a034..1cf893e 100644 --- a/include/asm-blackfin/mach-bf533/anomaly.h +++ b/include/asm-blackfin/mach-bf533/anomaly.h @@ -2,7 +2,7 @@ * File: include/asm-blackfin/mach-bf533/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2008 Analog Devices Inc. + * Copyright (C) 2004-2009 Analog Devices Inc. * Licensed under the GPL-2 or later. */ @@ -160,7 +160,7 @@ #define ANOMALY_05000301 (__SILICON_REVISION__ < 6) /* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */ #define ANOMALY_05000302 (__SILICON_REVISION__ < 5) -/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */ +/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */ #define ANOMALY_05000305 (__SILICON_REVISION__ < 5) /* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */ #define ANOMALY_05000306 (__SILICON_REVISION__ < 5) @@ -278,9 +278,12 @@ #define ANOMALY_05000266 (0) #define ANOMALY_05000323 (0) #define ANOMALY_05000353 (1) +#define ANOMALY_05000380 (0) #define ANOMALY_05000386 (1) #define ANOMALY_05000412 (0) #define ANOMALY_05000432 (0) #define ANOMALY_05000435 (0) +#define ANOMALY_05000447 (0) +#define ANOMALY_05000448 (0) #endif diff --git a/include/asm-blackfin/mach-bf533/ports.h b/include/asm-blackfin/mach-bf533/ports.h index 79bc54d..512d6df 100644 --- a/include/asm-blackfin/mach-bf533/ports.h +++ b/include/asm-blackfin/mach-bf533/ports.h @@ -5,22 +5,6 @@ #ifndef __BFIN_PERIPHERAL_PORT__ #define __BFIN_PERIPHERAL_PORT__ -/* Port F Masks */ -#define PF0 0x0001 -#define PF1 0x0002 -#define PF2 0x0004 -#define PF3 0x0008 -#define PF4 0x0010 -#define PF5 0x0020 -#define PF6 0x0040 -#define PF7 0x0080 -#define PF8 0x0100 -#define PF9 0x0200 -#define PF10 0x0400 -#define PF11 0x0800 -#define PF12 0x1000 -#define PF13 0x2000 -#define PF14 0x4000 -#define PF15 0x8000 +#include "../mach-common/bits/ports-f.h" #endif diff --git a/include/asm-blackfin/mach-bf537/ADSP-EDN-BF534-extended_cdef.h b/include/asm-blackfin/mach-bf537/ADSP-EDN-BF534-extended_cdef.h index b9e4d67..0700875 100644 --- a/include/asm-blackfin/mach-bf537/ADSP-EDN-BF534-extended_cdef.h +++ b/include/asm-blackfin/mach-bf537/ADSP-EDN-BF534-extended_cdef.h @@ -27,9 +27,9 @@ #define pSYSCR ((uint16_t volatile *)SYSCR) /* System Configuration Register */ #define bfin_read_SYSCR() bfin_read16(SYSCR) #define bfin_write_SYSCR(val) bfin_write16(SYSCR, val) -#define pSIC_RVECT ((uint32_t volatile *)SIC_RVECT) /* Interrupt Reset Vector Address Register */ -#define bfin_read_SIC_RVECT() bfin_read32(SIC_RVECT) -#define bfin_write_SIC_RVECT(val) bfin_write32(SIC_RVECT, val) +#define pSIC_RVECT ((uint16_t volatile *)SIC_RVECT) /* Interrupt Reset Vector Address Register */ +#define bfin_read_SIC_RVECT() bfin_read16(SIC_RVECT) +#define bfin_write_SIC_RVECT(val) bfin_write16(SIC_RVECT, val) #define pSIC_IMASK ((uint32_t volatile *)SIC_IMASK) /* Interrupt Mask Register */ #define bfin_read_SIC_IMASK() bfin_read32(SIC_IMASK) #define bfin_write_SIC_IMASK(val) bfin_write32(SIC_IMASK, val) @@ -304,7 +304,6 @@ #define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV) #define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV, val) #define pSPORT0_TX ((uint32_t volatile *)SPORT0_TX) /* SPORT0 TX Data Register */ -#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) #define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) #define pSPORT0_RX ((uint32_t volatile *)SPORT0_RX) /* SPORT0 RX Data Register */ #define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX) @@ -370,7 +369,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 TX Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RX ((uint32_t volatile *)SPORT1_RX) /* SPORT1 RX Data Register */ #define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX) diff --git a/include/asm-blackfin/mach-bf537/anomaly.h b/include/asm-blackfin/mach-bf537/anomaly.h index 9cb3912..1bfd80c 100644 --- a/include/asm-blackfin/mach-bf537/anomaly.h +++ b/include/asm-blackfin/mach-bf537/anomaly.h @@ -2,7 +2,7 @@ * File: include/asm-blackfin/mach-bf537/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2008 Analog Devices Inc. + * Copyright (C) 2004-2009 Analog Devices Inc. * Licensed under the GPL-2 or later. */ @@ -110,7 +110,7 @@ #define ANOMALY_05000301 (1) /* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */ #define ANOMALY_05000304 (__SILICON_REVISION__ < 3) -/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */ +/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */ #define ANOMALY_05000305 (__SILICON_REVISION__ < 3) /* SCKELOW Bit Does Not Maintain State Through Hibernate */ #define ANOMALY_05000307 (__SILICON_REVISION__ < 3) @@ -168,9 +168,12 @@ #define ANOMALY_05000323 (0) #define ANOMALY_05000353 (1) #define ANOMALY_05000363 (0) +#define ANOMALY_05000380 (0) #define ANOMALY_05000386 (1) #define ANOMALY_05000412 (0) #define ANOMALY_05000432 (0) #define ANOMALY_05000435 (0) +#define ANOMALY_05000447 (0) +#define ANOMALY_05000448 (0) #endif diff --git a/include/asm-blackfin/mach-bf537/ports.h b/include/asm-blackfin/mach-bf537/ports.h index cc28ba3..2f62934 100644 --- a/include/asm-blackfin/mach-bf537/ports.h +++ b/include/asm-blackfin/mach-bf537/ports.h @@ -21,58 +21,8 @@ #define PGRE 0x0400 #define PGTE 0x0800 -/* Port F Masks */ -#define PF0 0x0001 -#define PF1 0x0002 -#define PF2 0x0004 -#define PF3 0x0008 -#define PF4 0x0010 -#define PF5 0x0020 -#define PF6 0x0040 -#define PF7 0x0080 -#define PF8 0x0100 -#define PF9 0x0200 -#define PF10 0x0400 -#define PF11 0x0800 -#define PF12 0x1000 -#define PF13 0x2000 -#define PF14 0x4000 -#define PF15 0x8000 - -/* Port G Masks */ -#define PG0 0x0001 -#define PG1 0x0002 -#define PG2 0x0004 -#define PG3 0x0008 -#define PG4 0x0010 -#define PG5 0x0020 -#define PG6 0x0040 -#define PG7 0x0080 -#define PG8 0x0100 -#define PG9 0x0200 -#define PG10 0x0400 -#define PG11 0x0800 -#define PG12 0x1000 -#define PG13 0x2000 -#define PG14 0x4000 -#define PG15 0x8000 - -/* Port H Masks */ -#define PH0 0x0001 -#define PH1 0x0002 -#define PH2 0x0004 -#define PH3 0x0008 -#define PH4 0x0010 -#define PH5 0x0020 -#define PH6 0x0040 -#define PH7 0x0080 -#define PH8 0x0100 -#define PH9 0x0200 -#define PH10 0x0400 -#define PH11 0x0800 -#define PH12 0x1000 -#define PH13 0x2000 -#define PH14 0x4000 -#define PH15 0x8000 +#include "../mach-common/bits/ports-f.h" +#include "../mach-common/bits/ports-g.h" +#include "../mach-common/bits/ports-h.h" #endif diff --git a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF542-extended_cdef.h b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF542-extended_cdef.h index e9572a0..51d9cf2 100644 --- a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF542-extended_cdef.h +++ b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF542-extended_cdef.h @@ -3577,7 +3577,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 Transmit Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RCR1 ((uint16_t volatile *)SPORT1_RCR1) /* SPORT1 Receive Configuration 1 Register */ #define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1) @@ -3643,7 +3642,6 @@ #define bfin_read_SPORT2_TFSDIV() bfin_read16(SPORT2_TFSDIV) #define bfin_write_SPORT2_TFSDIV(val) bfin_write16(SPORT2_TFSDIV, val) #define pSPORT2_TX ((uint32_t volatile *)SPORT2_TX) /* SPORT2 Transmit Data Register */ -#define bfin_read_SPORT2_TX() bfin_read32(SPORT2_TX) #define bfin_write_SPORT2_TX(val) bfin_write32(SPORT2_TX, val) #define pSPORT2_RCR1 ((uint16_t volatile *)SPORT2_RCR1) /* SPORT2 Receive Configuration 1 Register */ #define bfin_read_SPORT2_RCR1() bfin_read16(SPORT2_RCR1) @@ -3709,7 +3707,6 @@ #define bfin_read_SPORT3_TFSDIV() bfin_read16(SPORT3_TFSDIV) #define bfin_write_SPORT3_TFSDIV(val) bfin_write16(SPORT3_TFSDIV, val) #define pSPORT3_TX ((uint32_t volatile *)SPORT3_TX) /* SPORT3 Transmit Data Register */ -#define bfin_read_SPORT3_TX() bfin_read32(SPORT3_TX) #define bfin_write_SPORT3_TX(val) bfin_write32(SPORT3_TX, val) #define pSPORT3_RCR1 ((uint16_t volatile *)SPORT3_RCR1) /* SPORT3 Receive Configuration 1 Register */ #define bfin_read_SPORT3_RCR1() bfin_read16(SPORT3_RCR1) diff --git a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF544-extended_cdef.h b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF544-extended_cdef.h index 968cd3e..4c0fdf5 100644 --- a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF544-extended_cdef.h +++ b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF544-extended_cdef.h @@ -4678,7 +4678,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 Transmit Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RCR1 ((uint16_t volatile *)SPORT1_RCR1) /* SPORT1 Receive Configuration 1 Register */ #define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1) @@ -4744,7 +4743,6 @@ #define bfin_read_SPORT2_TFSDIV() bfin_read16(SPORT2_TFSDIV) #define bfin_write_SPORT2_TFSDIV(val) bfin_write16(SPORT2_TFSDIV, val) #define pSPORT2_TX ((uint32_t volatile *)SPORT2_TX) /* SPORT2 Transmit Data Register */ -#define bfin_read_SPORT2_TX() bfin_read32(SPORT2_TX) #define bfin_write_SPORT2_TX(val) bfin_write32(SPORT2_TX, val) #define pSPORT2_RCR1 ((uint16_t volatile *)SPORT2_RCR1) /* SPORT2 Receive Configuration 1 Register */ #define bfin_read_SPORT2_RCR1() bfin_read16(SPORT2_RCR1) @@ -4810,7 +4808,6 @@ #define bfin_read_SPORT3_TFSDIV() bfin_read16(SPORT3_TFSDIV) #define bfin_write_SPORT3_TFSDIV(val) bfin_write16(SPORT3_TFSDIV, val) #define pSPORT3_TX ((uint32_t volatile *)SPORT3_TX) /* SPORT3 Transmit Data Register */ -#define bfin_read_SPORT3_TX() bfin_read32(SPORT3_TX) #define bfin_write_SPORT3_TX(val) bfin_write32(SPORT3_TX, val) #define pSPORT3_RCR1 ((uint16_t volatile *)SPORT3_RCR1) /* SPORT3 Receive Configuration 1 Register */ #define bfin_read_SPORT3_RCR1() bfin_read16(SPORT3_RCR1) diff --git a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF547-extended_cdef.h b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF547-extended_cdef.h index bd40f35..e0f76ae 100644 --- a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF547-extended_cdef.h +++ b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF547-extended_cdef.h @@ -2713,7 +2713,6 @@ #define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV) #define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV, val) #define pSPORT0_TX ((uint32_t volatile *)SPORT0_TX) /* SPORT0 Transmit Data Register */ -#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) #define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) #define pSPORT0_RCR1 ((uint16_t volatile *)SPORT0_RCR1) /* SPORT0 Receive Configuration 1 Register */ #define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1) @@ -2779,7 +2778,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 Transmit Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RCR1 ((uint16_t volatile *)SPORT1_RCR1) /* SPORT1 Receive Configuration 1 Register */ #define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1) @@ -2845,7 +2843,6 @@ #define bfin_read_SPORT2_TFSDIV() bfin_read16(SPORT2_TFSDIV) #define bfin_write_SPORT2_TFSDIV(val) bfin_write16(SPORT2_TFSDIV, val) #define pSPORT2_TX ((uint32_t volatile *)SPORT2_TX) /* SPORT2 Transmit Data Register */ -#define bfin_read_SPORT2_TX() bfin_read32(SPORT2_TX) #define bfin_write_SPORT2_TX(val) bfin_write32(SPORT2_TX, val) #define pSPORT2_RCR1 ((uint16_t volatile *)SPORT2_RCR1) /* SPORT2 Receive Configuration 1 Register */ #define bfin_read_SPORT2_RCR1() bfin_read16(SPORT2_RCR1) @@ -2911,7 +2908,6 @@ #define bfin_read_SPORT3_TFSDIV() bfin_read16(SPORT3_TFSDIV) #define bfin_write_SPORT3_TFSDIV(val) bfin_write16(SPORT3_TFSDIV, val) #define pSPORT3_TX ((uint32_t volatile *)SPORT3_TX) /* SPORT3 Transmit Data Register */ -#define bfin_read_SPORT3_TX() bfin_read32(SPORT3_TX) #define bfin_write_SPORT3_TX(val) bfin_write32(SPORT3_TX, val) #define pSPORT3_RCR1 ((uint16_t volatile *)SPORT3_RCR1) /* SPORT3 Receive Configuration 1 Register */ #define bfin_read_SPORT3_RCR1() bfin_read16(SPORT3_RCR1) diff --git a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF548-extended_cdef.h b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF548-extended_cdef.h index 77cd5dc..caf2f6f 100644 --- a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF548-extended_cdef.h +++ b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF548-extended_cdef.h @@ -4885,7 +4885,6 @@ #define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV) #define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV, val) #define pSPORT0_TX ((uint32_t volatile *)SPORT0_TX) /* SPORT0 Transmit Data Register */ -#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) #define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) #define pSPORT0_RCR1 ((uint16_t volatile *)SPORT0_RCR1) /* SPORT0 Receive Configuration 1 Register */ #define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1) @@ -4951,7 +4950,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 Transmit Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RCR1 ((uint16_t volatile *)SPORT1_RCR1) /* SPORT1 Receive Configuration 1 Register */ #define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1) @@ -5017,7 +5015,6 @@ #define bfin_read_SPORT2_TFSDIV() bfin_read16(SPORT2_TFSDIV) #define bfin_write_SPORT2_TFSDIV(val) bfin_write16(SPORT2_TFSDIV, val) #define pSPORT2_TX ((uint32_t volatile *)SPORT2_TX) /* SPORT2 Transmit Data Register */ -#define bfin_read_SPORT2_TX() bfin_read32(SPORT2_TX) #define bfin_write_SPORT2_TX(val) bfin_write32(SPORT2_TX, val) #define pSPORT2_RCR1 ((uint16_t volatile *)SPORT2_RCR1) /* SPORT2 Receive Configuration 1 Register */ #define bfin_read_SPORT2_RCR1() bfin_read16(SPORT2_RCR1) @@ -5083,7 +5080,6 @@ #define bfin_read_SPORT3_TFSDIV() bfin_read16(SPORT3_TFSDIV) #define bfin_write_SPORT3_TFSDIV(val) bfin_write16(SPORT3_TFSDIV, val) #define pSPORT3_TX ((uint32_t volatile *)SPORT3_TX) /* SPORT3 Transmit Data Register */ -#define bfin_read_SPORT3_TX() bfin_read32(SPORT3_TX) #define bfin_write_SPORT3_TX(val) bfin_write32(SPORT3_TX, val) #define pSPORT3_RCR1 ((uint16_t volatile *)SPORT3_RCR1) /* SPORT3 Receive Configuration 1 Register */ #define bfin_read_SPORT3_RCR1() bfin_read16(SPORT3_RCR1) diff --git a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF549-extended_cdef.h b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF549-extended_cdef.h index c5d3511..af90e4c 100644 --- a/include/asm-blackfin/mach-bf548/ADSP-EDN-BF549-extended_cdef.h +++ b/include/asm-blackfin/mach-bf548/ADSP-EDN-BF549-extended_cdef.h @@ -5233,7 +5233,6 @@ #define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV) #define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV, val) #define pSPORT0_TX ((uint32_t volatile *)SPORT0_TX) /* SPORT0 Transmit Data Register */ -#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) #define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) #define pSPORT0_RCR1 ((uint16_t volatile *)SPORT0_RCR1) /* SPORT0 Receive Configuration 1 Register */ #define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1) @@ -5299,7 +5298,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 Transmit Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RCR1 ((uint16_t volatile *)SPORT1_RCR1) /* SPORT1 Receive Configuration 1 Register */ #define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1) @@ -5365,7 +5363,6 @@ #define bfin_read_SPORT2_TFSDIV() bfin_read16(SPORT2_TFSDIV) #define bfin_write_SPORT2_TFSDIV(val) bfin_write16(SPORT2_TFSDIV, val) #define pSPORT2_TX ((uint32_t volatile *)SPORT2_TX) /* SPORT2 Transmit Data Register */ -#define bfin_read_SPORT2_TX() bfin_read32(SPORT2_TX) #define bfin_write_SPORT2_TX(val) bfin_write32(SPORT2_TX, val) #define pSPORT2_RCR1 ((uint16_t volatile *)SPORT2_RCR1) /* SPORT2 Receive Configuration 1 Register */ #define bfin_read_SPORT2_RCR1() bfin_read16(SPORT2_RCR1) @@ -5431,7 +5428,6 @@ #define bfin_read_SPORT3_TFSDIV() bfin_read16(SPORT3_TFSDIV) #define bfin_write_SPORT3_TFSDIV(val) bfin_write16(SPORT3_TFSDIV, val) #define pSPORT3_TX ((uint32_t volatile *)SPORT3_TX) /* SPORT3 Transmit Data Register */ -#define bfin_read_SPORT3_TX() bfin_read32(SPORT3_TX) #define bfin_write_SPORT3_TX(val) bfin_write32(SPORT3_TX, val) #define pSPORT3_RCR1 ((uint16_t volatile *)SPORT3_RCR1) /* SPORT3 Receive Configuration 1 Register */ #define bfin_read_SPORT3_RCR1() bfin_read16(SPORT3_RCR1) diff --git a/include/asm-blackfin/mach-bf548/anomaly.h b/include/asm-blackfin/mach-bf548/anomaly.h index 3b54309..882e40c 100644 --- a/include/asm-blackfin/mach-bf548/anomaly.h +++ b/include/asm-blackfin/mach-bf548/anomaly.h @@ -2,12 +2,12 @@ * File: include/asm-blackfin/mach-bf548/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2008 Analog Devices Inc. + * Copyright (C) 2004-2009 Analog Devices Inc. * Licensed under the GPL-2 or later. */ /* This file shoule be up to date with: - * - Revision G, 08/07/2008; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List + * - Revision H, 01/16/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List */ #ifndef _MACH_ANOMALY_H_ @@ -91,8 +91,6 @@ #define ANOMALY_05000371 (__SILICON_REVISION__ < 2) /* USB DP/DM Data Pins May Lose State When Entering Hibernate */ #define ANOMALY_05000372 (__SILICON_REVISION__ < 1) -/* Mobile DDR Operation Not Functional */ -#define ANOMALY_05000377 (1) /* Security/Authentication Speedpath Causes Authentication To Fail To Initiate */ #define ANOMALY_05000378 (__SILICON_REVISION__ < 2) /* 16-Bit NAND FLASH Boot Mode Is Not Functional */ @@ -157,8 +155,22 @@ #define ANOMALY_05000429 (__SILICON_REVISION__ < 2) /* Software System Reset Corrupts PLL_LOCKCNT Register */ #define ANOMALY_05000430 (__SILICON_REVISION__ >= 2) +/* Incorrect Use of Stack in Lockbox Firmware During Authentication */ +#define ANOMALY_05000431 (__SILICON_REVISION__ < 3) +/* OTP Write Accesses Not Supported */ +#define ANOMALY_05000442 (__SILICON_REVISION__ < 1) /* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */ #define ANOMALY_05000443 (1) +/* CDMAPRIO and L2DMAPRIO Bits in the SYSCR Register Are Not Functional */ +#define ANOMALY_05000446 (1) +/* UART IrDA Receiver Fails on Extended Bit Pulses */ +#define ANOMALY_05000447 (1) +/* DDR Clock Duty Cycle Spec Violation (tCH, tCL) */ +#define ANOMALY_05000448 (__SILICON_REVISION__ == 1) +/* Reduced Timing Margins on DDR Output Setup and Hold (tDS and tDH) */ +#define ANOMALY_05000449 (__SILICON_REVISION__ == 1) +/* USB DMA Mode 1 Short Packet Data Corruption */ +#define ANOMALY_05000450 (1 /* Anomalies that don't exist on this proc */ #define ANOMALY_05000125 (0) @@ -171,10 +183,13 @@ #define ANOMALY_05000263 (0) #define ANOMALY_05000266 (0) #define ANOMALY_05000273 (0) +#define ANOMALY_05000278 (0) +#define ANOMALY_05000305 (0) #define ANOMALY_05000307 (0) #define ANOMALY_05000311 (0) #define ANOMALY_05000323 (0) #define ANOMALY_05000363 (0) +#define ANOMALY_05000380 (0) #define ANOMALY_05000412 (0) #define ANOMALY_05000432 (0) #define ANOMALY_05000435 (0) diff --git a/include/asm-blackfin/mach-bf548/ports.h b/include/asm-blackfin/mach-bf548/ports.h index 5f0e45e..50054f3 100644 --- a/include/asm-blackfin/mach-bf548/ports.h +++ b/include/asm-blackfin/mach-bf548/ports.h @@ -92,184 +92,15 @@ #define PORT_x_MUX_15_FUNC_3 (PORT_x_MUX_FUNC_3 << 30) #define PORT_x_MUX_15_FUNC_4 (PORT_x_MUX_FUNC_4 << 30) -/* Port A Masks */ -#define PA0 0x0001 -#define PA1 0x0002 -#define PA2 0x0004 -#define PA3 0x0008 -#define PA4 0x0010 -#define PA5 0x0020 -#define PA6 0x0040 -#define PA7 0x0080 -#define PA8 0x0100 -#define PA9 0x0200 -#define PA10 0x0400 -#define PA11 0x0800 -#define PA12 0x1000 -#define PA13 0x2000 -#define PA14 0x4000 -#define PA15 0x8000 - -/* Port B Masks */ -#define PB0 0x0001 -#define PB1 0x0002 -#define PB2 0x0004 -#define PB3 0x0008 -#define PB4 0x0010 -#define PB5 0x0020 -#define PB6 0x0040 -#define PB7 0x0080 -#define PB8 0x0100 -#define PB9 0x0200 -#define PB10 0x0400 -#define PB11 0x0800 -#define PB12 0x1000 -#define PB13 0x2000 -#define PB14 0x4000 -#define PB15 0x8000 - -/* Port C Masks */ -#define PC0 0x0001 -#define PC1 0x0002 -#define PC2 0x0004 -#define PC3 0x0008 -#define PC4 0x0010 -#define PC5 0x0020 -#define PC6 0x0040 -#define PC7 0x0080 -#define PC8 0x0100 -#define PC9 0x0200 -#define PC10 0x0400 -#define PC11 0x0800 -#define PC12 0x1000 -#define PC13 0x2000 -#define PC14 0x4000 -#define PC15 0x8000 - -/* Port F Masks */ -#define PD0 0x0001 -#define PD1 0x0002 -#define PD2 0x0004 -#define PD3 0x0008 -#define PD4 0x0010 -#define PD5 0x0020 -#define PD6 0x0040 -#define PD7 0x0080 -#define PD8 0x0100 -#define PD9 0x0200 -#define PD10 0x0400 -#define PD11 0x0800 -#define PD12 0x1000 -#define PD13 0x2000 -#define PD14 0x4000 -#define PD15 0x8000 - -/* Port F Masks */ -#define PE0 0x0001 -#define PE1 0x0002 -#define PE2 0x0004 -#define PE3 0x0008 -#define PE4 0x0010 -#define PE5 0x0020 -#define PE6 0x0040 -#define PE7 0x0080 -#define PE8 0x0100 -#define PE9 0x0200 -#define PE10 0x0400 -#define PE11 0x0800 -#define PE12 0x1000 -#define PE13 0x2000 -#define PE14 0x4000 -#define PE15 0x8000 - -/* Port F Masks */ -#define PF0 0x0001 -#define PF1 0x0002 -#define PF2 0x0004 -#define PF3 0x0008 -#define PF4 0x0010 -#define PF5 0x0020 -#define PF6 0x0040 -#define PF7 0x0080 -#define PF8 0x0100 -#define PF9 0x0200 -#define PF10 0x0400 -#define PF11 0x0800 -#define PF12 0x1000 -#define PF13 0x2000 -#define PF14 0x4000 -#define PF15 0x8000 - -/* Port G Masks */ -#define PG0 0x0001 -#define PG1 0x0002 -#define PG2 0x0004 -#define PG3 0x0008 -#define PG4 0x0010 -#define PG5 0x0020 -#define PG6 0x0040 -#define PG7 0x0080 -#define PG8 0x0100 -#define PG9 0x0200 -#define PG10 0x0400 -#define PG11 0x0800 -#define PG12 0x1000 -#define PG13 0x2000 -#define PG14 0x4000 -#define PG15 0x8000 - -/* Port H Masks */ -#define PH0 0x0001 -#define PH1 0x0002 -#define PH2 0x0004 -#define PH3 0x0008 -#define PH4 0x0010 -#define PH5 0x0020 -#define PH6 0x0040 -#define PH7 0x0080 -#define PH8 0x0100 -#define PH9 0x0200 -#define PH10 0x0400 -#define PH11 0x0800 -#define PH12 0x1000 -#define PH13 0x2000 -#define PH14 0x4000 -#define PH15 0x8000 - -/* Port I Masks */ -#define PI0 0x0001 -#define PI1 0x0002 -#define PI2 0x0004 -#define PI3 0x0008 -#define PI4 0x0010 -#define PI5 0x0020 -#define PI6 0x0040 -#define PI7 0x0080 -#define PI8 0x0100 -#define PI9 0x0200 -#define PI10 0x0400 -#define PI11 0x0800 -#define PI12 0x1000 -#define PI13 0x2000 -#define PI14 0x4000 -#define PI15 0x8000 - -/* Port I Masks */ -#define PJ0 0x0001 -#define PJ1 0x0002 -#define PJ2 0x0004 -#define PJ3 0x0008 -#define PJ4 0x0010 -#define PJ5 0x0020 -#define PJ6 0x0040 -#define PJ7 0x0080 -#define PJ8 0x0100 -#define PJ9 0x0200 -#define PJ10 0x0400 -#define PJ11 0x0800 -#define PJ12 0x1000 -#define PJ13 0x2000 -#define PJ14 0x4000 -#define PJ15 0x8000 +#include "../mach-common/bits/ports-a.h" +#include "../mach-common/bits/ports-b.h" +#include "../mach-common/bits/ports-c.h" +#include "../mach-common/bits/ports-d.h" +#include "../mach-common/bits/ports-e.h" +#include "../mach-common/bits/ports-f.h" +#include "../mach-common/bits/ports-g.h" +#include "../mach-common/bits/ports-h.h" +#include "../mach-common/bits/ports-i.h" +#include "../mach-common/bits/ports-j.h" #endif diff --git a/include/asm-blackfin/mach-bf561/BF561_cdef.h b/include/asm-blackfin/mach-bf561/BF561_cdef.h index d8883f3..e2c165a 100644 --- a/include/asm-blackfin/mach-bf561/BF561_cdef.h +++ b/include/asm-blackfin/mach-bf561/BF561_cdef.h @@ -244,9 +244,9 @@ #define pSICA_SWRST ((uint16_t volatile *)SICA_SWRST) #define bfin_read_SICA_SWRST() bfin_read16(SICA_SWRST) #define bfin_write_SICA_SWRST(val) bfin_write16(SICA_SWRST, val) -#define pSICA_SYSCR ((uint32_t volatile *)SICA_SYSCR) -#define bfin_read_SICA_SYSCR() bfin_read32(SICA_SYSCR) -#define bfin_write_SICA_SYSCR(val) bfin_write32(SICA_SYSCR, val) +#define pSICA_SYSCR ((uint16_t volatile *)SICA_SYSCR) +#define bfin_read_SICA_SYSCR() bfin_read16(SICA_SYSCR) +#define bfin_write_SICA_SYSCR(val) bfin_write16(SICA_SYSCR, val) #define pSICA_RVECT ((uint16_t volatile *)SICA_RVECT) #define bfin_read_SICA_RVECT() bfin_read16(SICA_RVECT) #define bfin_write_SICA_RVECT(val) bfin_write16(SICA_RVECT, val) @@ -295,9 +295,9 @@ #define pSICB_SWRST ((uint16_t volatile *)SICB_SWRST) #define bfin_read_SICB_SWRST() bfin_read16(SICB_SWRST) #define bfin_write_SICB_SWRST(val) bfin_write16(SICB_SWRST, val) -#define pSICB_SYSCR ((uint32_t volatile *)SICB_SYSCR) -#define bfin_read_SICB_SYSCR() bfin_read32(SICB_SYSCR) -#define bfin_write_SICB_SYSCR(val) bfin_write32(SICB_SYSCR, val) +#define pSICB_SYSCR ((uint16_t volatile *)SICB_SYSCR) +#define bfin_read_SICB_SYSCR() bfin_read16(SICB_SYSCR) +#define bfin_write_SICB_SYSCR(val) bfin_write16(SICB_SYSCR, val) #define pSICB_RVECT ((uint16_t volatile *)SICB_RVECT) #define bfin_read_SICB_RVECT() bfin_read16(SICB_RVECT) #define bfin_write_SICB_RVECT(val) bfin_write16(SICB_RVECT, val) diff --git a/include/asm-blackfin/mach-bf561/anomaly.h b/include/asm-blackfin/mach-bf561/anomaly.h index 1a9e175..d0b0b35 100644 --- a/include/asm-blackfin/mach-bf561/anomaly.h +++ b/include/asm-blackfin/mach-bf561/anomaly.h @@ -2,7 +2,7 @@ * File: include/asm-blackfin/mach-bf561/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2008 Analog Devices Inc. + * Copyright (C) 2004-2009 Analog Devices Inc. * Licensed under the GPL-2 or later. */ @@ -224,7 +224,7 @@ #define ANOMALY_05000301 (1) /* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */ #define ANOMALY_05000302 (1) -/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */ +/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */ #define ANOMALY_05000305 (__SILICON_REVISION__ < 5) /* SCKELOW Bit Does Not Maintain State Through Hibernate */ #define ANOMALY_05000307 (__SILICON_REVISION__ < 5) @@ -283,8 +283,11 @@ #define ANOMALY_05000273 (0) #define ANOMALY_05000311 (0) #define ANOMALY_05000353 (1) +#define ANOMALY_05000380 (0) #define ANOMALY_05000386 (1) #define ANOMALY_05000432 (0) #define ANOMALY_05000435 (0) +#define ANOMALY_05000447 (0) +#define ANOMALY_05000448 (0) #endif diff --git a/include/asm-blackfin/mach-bf561/def_local.h b/include/asm-blackfin/mach-bf561/def_local.h index 3ddd689..597dcec 100644 --- a/include/asm-blackfin/mach-bf561/def_local.h +++ b/include/asm-blackfin/mach-bf561/def_local.h @@ -8,3 +8,5 @@ #define bfin_write_WDOG_CNT(val) bfin_write_WDOGA_CNT(val) #define bfin_write_WDOG_CTL(val) bfin_write_WDOGA_CTL(val) #define bfin_write_WDOG_STAT(val) bfin_write_WDOGA_STAT(val) + +#include "ports.h" diff --git a/include/asm-blackfin/mach-bf561/ports.h b/include/asm-blackfin/mach-bf561/ports.h new file mode 100644 index 0000000..194d4a3 --- /dev/null +++ b/include/asm-blackfin/mach-bf561/ports.h @@ -0,0 +1,44 @@ +/* + * Port Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT__ +#define __BFIN_PERIPHERAL_PORT__ + +#include "../mach-common/bits/ports-f.h" + +/* The non-standard PF16+ */ +#define PF16 (1 << 0) +#define PF17 (1 << 1) +#define PF18 (1 << 2) +#define PF19 (1 << 3) +#define PF20 (1 << 4) +#define PF21 (1 << 5) +#define PF22 (1 << 6) +#define PF23 (1 << 7) +#define PF24 (1 << 8) +#define PF25 (1 << 9) +#define PF26 (1 << 10) +#define PF27 (1 << 11) +#define PF28 (1 << 12) +#define PF29 (1 << 13) +#define PF30 (1 << 14) +#define PF31 (1 << 15) +#define PF32 (1 << 0) +#define PF33 (1 << 1) +#define PF34 (1 << 2) +#define PF35 (1 << 3) +#define PF36 (1 << 4) +#define PF37 (1 << 5) +#define PF38 (1 << 6) +#define PF39 (1 << 7) +#define PF40 (1 << 8) +#define PF41 (1 << 9) +#define PF42 (1 << 10) +#define PF43 (1 << 11) +#define PF44 (1 << 12) +#define PF45 (1 << 13) +#define PF46 (1 << 14) +#define PF47 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/ADSP-EDN-DUAL-CORE-extended_cdef.h b/include/asm-blackfin/mach-common/ADSP-EDN-DUAL-CORE-extended_cdef.h index c0c7e1e..43f3850 100644 --- a/include/asm-blackfin/mach-common/ADSP-EDN-DUAL-CORE-extended_cdef.h +++ b/include/asm-blackfin/mach-common/ADSP-EDN-DUAL-CORE-extended_cdef.h @@ -1798,7 +1798,6 @@ #define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) #define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) #define pSPORT0_RX ((uint32_t volatile *)SPORT0_RX) -#define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX) #define bfin_write_SPORT0_RX(val) bfin_write32(SPORT0_RX, val) #define pSPORT0_RCR1 ((uint16_t volatile *)SPORT0_RCR1) #define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1) @@ -1861,7 +1860,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RX ((uint32_t volatile *)SPORT1_RX) #define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX) diff --git a/include/asm-blackfin/mach-common/ADSP-EDN-extended_cdef.h b/include/asm-blackfin/mach-common/ADSP-EDN-extended_cdef.h index 4c439e5..2e61b5f 100644 --- a/include/asm-blackfin/mach-common/ADSP-EDN-extended_cdef.h +++ b/include/asm-blackfin/mach-common/ADSP-EDN-extended_cdef.h @@ -900,9 +900,9 @@ #define pSWRST ((uint16_t volatile *)SWRST) /* Software Reset Register (16-bit) */ #define bfin_read_SWRST() bfin_read16(SWRST) #define bfin_write_SWRST(val) bfin_write16(SWRST, val) -#define pSYSCR ((uint32_t volatile *)SYSCR) /* System Configuration register */ -#define bfin_read_SYSCR() bfin_read32(SYSCR) -#define bfin_write_SYSCR(val) bfin_write32(SYSCR, val) +#define pSYSCR ((uint16_t volatile *)SYSCR) /* System Configuration register */ +#define bfin_read_SYSCR() bfin_read16(SYSCR) +#define bfin_write_SYSCR(val) bfin_write16(SYSCR, val) #define pEVT_OVERRIDE ((uint32_t volatile *)EVT_OVERRIDE) #define bfin_read_EVT_OVERRIDE() bfin_read32(EVT_OVERRIDE) #define bfin_write_EVT_OVERRIDE(val) bfin_write32(EVT_OVERRIDE, val) @@ -1039,7 +1039,6 @@ #define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV) #define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV, val) #define pSPORT0_TX ((uint32_t volatile *)SPORT0_TX) /* SPORT0 TX Data Register */ -#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX) #define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val) #define pSPORT0_RX ((uint32_t volatile *)SPORT0_RX) /* SPORT0 RX Data Register */ #define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX) @@ -1081,7 +1080,6 @@ #define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV) #define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV, val) #define pSPORT1_TX ((uint32_t volatile *)SPORT1_TX) /* SPORT1 TX Data Register */ -#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX) #define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val) #define pSPORT1_RX ((uint32_t volatile *)SPORT1_RX) /* SPORT1 RX Data Register */ #define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX) diff --git a/include/asm-blackfin/mach-common/bits/lockbox.h b/include/asm-blackfin/mach-common/bits/lockbox.h index 8b696f3..77f849e 100644 --- a/include/asm-blackfin/mach-common/bits/lockbox.h +++ b/include/asm-blackfin/mach-common/bits/lockbox.h @@ -11,52 +11,52 @@ /* SESR argument structure. Expected to reside at 0xFF900018. */ typedef struct SESR_args { - unsigned short usFlags; /* security firmware flags */ - unsigned short usIRQMask; /* interrupt mask */ - unsigned long ulMessageSize; /* message length in bytes */ - unsigned long ulSFEntryPoint; /* entry point of secure function */ - unsigned long ulMessagePtr; /* pointer to the buffer containing */ - /* the digital signature and message */ - unsigned long ulReserved1; /* reserved */ - unsigned long ulReserved2; /* reserved */ + unsigned short usFlags; /* security firmware flags */ + unsigned short usIRQMask; /* interrupt mask */ + unsigned long ulMessageSize; /* message length in bytes */ + unsigned long ulSFEntryPoint; /* entry point of secure function */ + unsigned long ulMessagePtr; /* pointer to the buffer containing + the digital signature and message */ + unsigned long ulReserved1; /* reserved */ + unsigned long ulReserved2; /* reserved */ } tSESR_args; /* Secure Entry Service Routine */ -void (* const sesr)(void) = (void *)_BOOTROM_SESR; +static void (* const sesr)(void) = (void *)_BOOTROM_SESR; #endif -/* SESR flags argument bitfields */ -#define SESR_FLAGS_STAY_AT_NMI 0x0000 -#define SESR_FLAGS_DROP_BELOW_NMI 0x0001 -#define SESR_FLAGS_NO_SF_DMA 0x0000 -#define SESR_FLAGS_DMA_SF_TO_RUN_DEST 0x0002 -#define SESR_FLAGS_USE_ADI_PUB_KEY 0x0000 -#define SESR_FLAGS_USE_CUST_PUB_KEY 0x0100 +/* SESR flags argument bitfields */ +#define SESR_FLAGS_STAY_AT_NMI 0x0000 +#define SESR_FLAGS_DROP_BELOW_NMI 0x0001 +#define SESR_FLAGS_NO_SF_DMA 0x0000 +#define SESR_FLAGS_DMA_SF_TO_RUN_DEST 0x0002 +#define SESR_FLAGS_USE_ADI_PUB_KEY 0x0000 +#define SESR_FLAGS_USE_CUST_PUB_KEY 0x0100 /* Bit masks for SECURE_SYSSWT */ -#define EMUDABL 0x00000001 /* Emulation Disable */ -#define RSTDABL 0x00000002 /* Reset Disable */ -#define L1IDABL 0x0000001c /* L1 Instruction Memory Disable */ -#define L1DADABL 0x000000e0 /* L1 Data Bank A Memory Disable */ -#define L1DBDABL 0x00000700 /* L1 Data Bank B Memory Disable */ -#define DMA0OVR 0x00000800 /* DMA0 Memory Access Override */ -#define DMA1OVR 0x00001000 /* DMA1 Memory Access Override */ -#define EMUOVR 0x00004000 /* Emulation Override */ -#define OTPSEN 0x00008000 /* OTP Secrets Enable */ -#define L2DABL 0x00070000 /* L2 Memory Disable */ +#define EMUDABL 0x00000001 /* Emulation Disable */ +#define RSTDABL 0x00000002 /* Reset Disable */ +#define L1IDABL 0x0000001c /* L1 Instruction Memory Disable */ +#define L1DADABL 0x000000e0 /* L1 Data Bank A Memory Disable */ +#define L1DBDABL 0x00000700 /* L1 Data Bank B Memory Disable */ +#define DMA0OVR 0x00000800 /* DMA0 Memory Access Override */ +#define DMA1OVR 0x00001000 /* DMA1 Memory Access Override */ +#define EMUOVR 0x00004000 /* Emulation Override */ +#define OTPSEN 0x00008000 /* OTP Secrets Enable */ +#define L2DABL 0x00070000 /* L2 Memory Disable */ /* Bit masks for SECURE_CONTROL */ -#define SECURE0 0x0001 /* SECURE 0 */ -#define SECURE1 0x0002 /* SECURE 1 */ -#define SECURE2 0x0004 /* SECURE 2 */ -#define SECURE3 0x0008 /* SECURE 3 */ +#define SECURE0 0x0001 /* SECURE 0 */ +#define SECURE1 0x0002 /* SECURE 1 */ +#define SECURE2 0x0004 /* SECURE 2 */ +#define SECURE3 0x0008 /* SECURE 3 */ /* Bit masks for SECURE_STATUS */ -#define SECMODE 0x0003 /* Secured Mode Control State */ -#define NMI 0x0004 /* Non Maskable Interrupt */ -#define AFVALID 0x0008 /* Authentication Firmware Valid */ -#define AFEXIT 0x0010 /* Authentication Firmware Exit */ -#define SECSTAT 0x00e0 /* Secure Status */ +#define SECMODE 0x0003 /* Secured Mode Control State */ +#define NMI 0x0004 /* Non Maskable Interrupt */ +#define AFVALID 0x0008 /* Authentication Firmware Valid */ +#define AFEXIT 0x0010 /* Authentication Firmware Exit */ +#define SECSTAT 0x00e0 /* Secure Status */ #endif diff --git a/include/asm-blackfin/mach-common/bits/ports-a.h b/include/asm-blackfin/mach-common/bits/ports-a.h new file mode 100644 index 0000000..9f78a76 --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-a.h @@ -0,0 +1,25 @@ +/* + * Port A Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_A__ +#define __BFIN_PERIPHERAL_PORT_A__ + +#define PA0 (1 << 0) +#define PA1 (1 << 1) +#define PA2 (1 << 2) +#define PA3 (1 << 3) +#define PA4 (1 << 4) +#define PA5 (1 << 5) +#define PA6 (1 << 6) +#define PA7 (1 << 7) +#define PA8 (1 << 8) +#define PA9 (1 << 9) +#define PA10 (1 << 10) +#define PA11 (1 << 11) +#define PA12 (1 << 12) +#define PA13 (1 << 13) +#define PA14 (1 << 14) +#define PA15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-b.h b/include/asm-blackfin/mach-common/bits/ports-b.h new file mode 100644 index 0000000..b81702f --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-b.h @@ -0,0 +1,25 @@ +/* + * Port B Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_B__ +#define __BFIN_PERIPHERAL_PORT_B__ + +#define PB0 (1 << 0) +#define PB1 (1 << 1) +#define PB2 (1 << 2) +#define PB3 (1 << 3) +#define PB4 (1 << 4) +#define PB5 (1 << 5) +#define PB6 (1 << 6) +#define PB7 (1 << 7) +#define PB8 (1 << 8) +#define PB9 (1 << 9) +#define PB10 (1 << 10) +#define PB11 (1 << 11) +#define PB12 (1 << 12) +#define PB13 (1 << 13) +#define PB14 (1 << 14) +#define PB15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-c.h b/include/asm-blackfin/mach-common/bits/ports-c.h new file mode 100644 index 0000000..3cc665e --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-c.h @@ -0,0 +1,25 @@ +/* + * Port C Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_C__ +#define __BFIN_PERIPHERAL_PORT_C__ + +#define PC0 (1 << 0) +#define PC1 (1 << 1) +#define PC2 (1 << 2) +#define PC3 (1 << 3) +#define PC4 (1 << 4) +#define PC5 (1 << 5) +#define PC6 (1 << 6) +#define PC7 (1 << 7) +#define PC8 (1 << 8) +#define PC9 (1 << 9) +#define PC10 (1 << 10) +#define PC11 (1 << 11) +#define PC12 (1 << 12) +#define PC13 (1 << 13) +#define PC14 (1 << 14) +#define PC15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-d.h b/include/asm-blackfin/mach-common/bits/ports-d.h new file mode 100644 index 0000000..868c6a0 --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-d.h @@ -0,0 +1,25 @@ +/* + * Port D Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_D__ +#define __BFIN_PERIPHERAL_PORT_D__ + +#define PD0 (1 << 0) +#define PD1 (1 << 1) +#define PD2 (1 << 2) +#define PD3 (1 << 3) +#define PD4 (1 << 4) +#define PD5 (1 << 5) +#define PD6 (1 << 6) +#define PD7 (1 << 7) +#define PD8 (1 << 8) +#define PD9 (1 << 9) +#define PD10 (1 << 10) +#define PD11 (1 << 11) +#define PD12 (1 << 12) +#define PD13 (1 << 13) +#define PD14 (1 << 14) +#define PD15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-e.h b/include/asm-blackfin/mach-common/bits/ports-e.h new file mode 100644 index 0000000..c88b0d0 --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-e.h @@ -0,0 +1,25 @@ +/* + * Port E Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_E__ +#define __BFIN_PERIPHERAL_PORT_E__ + +#define PE0 (1 << 0) +#define PE1 (1 << 1) +#define PE2 (1 << 2) +#define PE3 (1 << 3) +#define PE4 (1 << 4) +#define PE5 (1 << 5) +#define PE6 (1 << 6) +#define PE7 (1 << 7) +#define PE8 (1 << 8) +#define PE9 (1 << 9) +#define PE10 (1 << 10) +#define PE11 (1 << 11) +#define PE12 (1 << 12) +#define PE13 (1 << 13) +#define PE14 (1 << 14) +#define PE15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-f.h b/include/asm-blackfin/mach-common/bits/ports-f.h new file mode 100644 index 0000000..d6af206 --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-f.h @@ -0,0 +1,25 @@ +/* + * Port F Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_F__ +#define __BFIN_PERIPHERAL_PORT_F__ + +#define PF0 (1 << 0) +#define PF1 (1 << 1) +#define PF2 (1 << 2) +#define PF3 (1 << 3) +#define PF4 (1 << 4) +#define PF5 (1 << 5) +#define PF6 (1 << 6) +#define PF7 (1 << 7) +#define PF8 (1 << 8) +#define PF9 (1 << 9) +#define PF10 (1 << 10) +#define PF11 (1 << 11) +#define PF12 (1 << 12) +#define PF13 (1 << 13) +#define PF14 (1 << 14) +#define PF15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-g.h b/include/asm-blackfin/mach-common/bits/ports-g.h new file mode 100644 index 0000000..09355d3 --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-g.h @@ -0,0 +1,25 @@ +/* + * Port G Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_G__ +#define __BFIN_PERIPHERAL_PORT_G__ + +#define PG0 (1 << 0) +#define PG1 (1 << 1) +#define PG2 (1 << 2) +#define PG3 (1 << 3) +#define PG4 (1 << 4) +#define PG5 (1 << 5) +#define PG6 (1 << 6) +#define PG7 (1 << 7) +#define PG8 (1 << 8) +#define PG9 (1 << 9) +#define PG10 (1 << 10) +#define PG11 (1 << 11) +#define PG12 (1 << 12) +#define PG13 (1 << 13) +#define PG14 (1 << 14) +#define PG15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-h.h b/include/asm-blackfin/mach-common/bits/ports-h.h new file mode 100644 index 0000000..fa3910c --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-h.h @@ -0,0 +1,25 @@ +/* + * Port H Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_H__ +#define __BFIN_PERIPHERAL_PORT_H__ + +#define PH0 (1 << 0) +#define PH1 (1 << 1) +#define PH2 (1 << 2) +#define PH3 (1 << 3) +#define PH4 (1 << 4) +#define PH5 (1 << 5) +#define PH6 (1 << 6) +#define PH7 (1 << 7) +#define PH8 (1 << 8) +#define PH9 (1 << 9) +#define PH10 (1 << 10) +#define PH11 (1 << 11) +#define PH12 (1 << 12) +#define PH13 (1 << 13) +#define PH14 (1 << 14) +#define PH15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-i.h b/include/asm-blackfin/mach-common/bits/ports-i.h new file mode 100644 index 0000000..f176f08 --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-i.h @@ -0,0 +1,25 @@ +/* + * Port I Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_I__ +#define __BFIN_PERIPHERAL_PORT_I__ + +#define PI0 (1 << 0) +#define PI1 (1 << 1) +#define PI2 (1 << 2) +#define PI3 (1 << 3) +#define PI4 (1 << 4) +#define PI5 (1 << 5) +#define PI6 (1 << 6) +#define PI7 (1 << 7) +#define PI8 (1 << 8) +#define PI9 (1 << 9) +#define PI10 (1 << 10) +#define PI11 (1 << 11) +#define PI12 (1 << 12) +#define PI13 (1 << 13) +#define PI14 (1 << 14) +#define PI15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/mach-common/bits/ports-j.h b/include/asm-blackfin/mach-common/bits/ports-j.h new file mode 100644 index 0000000..924123e --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/ports-j.h @@ -0,0 +1,25 @@ +/* + * Port J Masks + */ + +#ifndef __BFIN_PERIPHERAL_PORT_J__ +#define __BFIN_PERIPHERAL_PORT_J__ + +#define PJ0 (1 << 0) +#define PJ1 (1 << 1) +#define PJ2 (1 << 2) +#define PJ3 (1 << 3) +#define PJ4 (1 << 4) +#define PJ5 (1 << 5) +#define PJ6 (1 << 6) +#define PJ7 (1 << 7) +#define PJ8 (1 << 8) +#define PJ9 (1 << 9) +#define PJ10 (1 << 10) +#define PJ11 (1 << 11) +#define PJ12 (1 << 12) +#define PJ13 (1 << 13) +#define PJ14 (1 << 14) +#define PJ15 (1 << 15) + +#endif diff --git a/include/asm-blackfin/net.h b/include/asm-blackfin/net.h new file mode 100644 index 0000000..97cb466 --- /dev/null +++ b/include/asm-blackfin/net.h @@ -0,0 +1,28 @@ +/* + * net.h - misc Blackfin network helpers + * + * Copyright (c) 2008-2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __ASM_BFIN_RAND_MAC__ +#define __ASM_BFIN_RAND_MAC__ + +/* If the board does not have a real MAC assigned to it, then generate a + * locally administrated pseudo-random one based on CYCLES and compile date. + */ +static inline void bfin_gen_rand_mac(uchar *mac_addr) +{ + /* make something up */ + const char s[] = __DATE__; + size_t i; + u32 cycles; + for (i = 0; i < 6; ++i) { + asm("%0 = CYCLES;" : "=r" (cycles)); + mac_addr[i] = cycles ^ s[i]; + } + mac_addr[0] = (mac_addr[0] | 0x02) & ~0x01; /* make it local unicast */ +} + +#endif diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h index 48c0252..eb08890 100644 --- a/include/configs/bf533-ezkit.h +++ b/include/configs/bf533-ezkit.h @@ -2,213 +2,155 @@ * U-boot - Configuration file for BF533 EZKIT board */ -#ifndef __CONFIG_EZKIT533_H__ -#define __CONFIG_EZKIT533_H__ +#ifndef __CONFIG_BF533_EZKIT_H__ +#define __CONFIG_BF533_EZKIT_H__ #include <asm/blackfin-config-pre.h> -#define CONFIG_BAUDRATE 57600 -#define CONFIG_BOOTDELAY 5 -#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf533-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_LOADADDR 0x01000000 /* default load address */ -#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux" -/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */ -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x20310300 +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 27000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 22 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 -#if 0 -#define CONFIG_MII -#define CONFIG_SYS_DISCOVER_PHY -#endif -#define CONFIG_RTC_BFIN 1 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ - -#define CONFIG_PANIC_HANG 1 - -#define CONFIG_BFIN_CPU bf533-0.3 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON - -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 27000000 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 22 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) +/* + * Memory Settings + */ +#define CONFIG_MEM_SIZE 32 +/* Early EZKITs had 32megs, but later have 64megs */ +#if (CONFIG_MEM_SIZE == 64) +# define CONFIG_MEM_ADD_WDTH 10 #else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) +# define CONFIG_MEM_ADD_WDTH 9 #endif -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif +#define CONFIG_EBIU_SDRRC_VAL 0x398 +#define CONFIG_EBIU_SDGCTL_VAL 0x91118d -#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC16M16A2TG_75 1 +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_LOADS_ECHO 1 +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* - * BOOTP options + * Network Settings */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20310300 +#define SMC91111_EEPROM_INIT() \ + do { \ + *pFIO_DIR |= PF1; \ + *pFIO_FLAG_S = PF1; \ + SSYNC(); \ + } while (0) +#define CONFIG_HOSTNAME bf533-ezkit +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ /* - * Command line configuration. + * Flash Settings */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_DATE - - -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600" - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR 0x01000000 /* default load address */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024) #define CONFIG_SYS_FLASH_BASE 0x20000000 - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) - -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -#define CONFIG_SYS_FLASH0_BASE 0x20000000 -#define CONFIG_SYS_FLASH1_BASE 0x20200000 -#define CONFIG_SYS_FLASH2_BASE 0x20280000 -#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 40 /* max number of sectors on one chip */ - -#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_SYS_MAX_FLASH_BANKS 3 +#define CONFIG_SYS_MAX_FLASH_SECT 40 +#define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR 0x20020000 -#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ - -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11 - - -/* - * Stack sizes - */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#define POLL_MODE 1 +#define CONFIG_ENV_SECT_SIZE 0x10000 #define FLASH_TOT_SECT 40 -#define FLASH_SIZE 0x220000 -#define CONFIG_SYS_FLASH_SIZE 0x220000 -/* - * Initialize PSD4256 registers for using I2C - */ -#define CONFIG_MISC_INIT_R /* - * I2C settings + * I2C Settings * By default PF1 is used as SDA and PF0 as SCL on the Stamp board */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -/* - * Software (bit-bang) I2C driver configuration - */ -#define PF_SCL PF0 -#define PF_SDA PF1 - -#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") -#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") -#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") -#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") -#define I2C_SDA(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SDA; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SDA; \ - asm("ssync;"); \ - } -#define I2C_SCL(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SCL; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SCL; \ - asm("ssync;"); \ - } -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#define CONFIG_SOFT_I2C +#ifdef CONFIG_SOFT_I2C +#define PF_SCL PF0 +#define PF_SDA PF1 +#define I2C_INIT \ + do { \ + *pFIO_DIR |= PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_ACTIVE \ + do { \ + *pFIO_DIR |= PF_SDA; \ + *pFIO_INEN &= ~PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_TRISTATE \ + do { \ + *pFIO_DIR &= ~PF_SDA; \ + *pFIO_INEN |= PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SDA; \ + else \ + *pFIO_FLAG_C = PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SCL; \ + else \ + *pFIO_FLAG_C = PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_SYS_I2C_SLAVE 0 +#endif -#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ -#define CONFIG_EBIU_SDRRC_VAL 0x398 -#define CONFIG_EBIU_SDGCTL_VAL 0x91118d -#define CONFIG_EBIU_SDBCTL_VAL 0x13 +/* + * Misc Settings + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 + -#define CONFIG_EBIU_AMGCTL_VAL 0xFF -#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 -#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> #include <asm/blackfin-config-post.h> diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index ee41c7e..d8e1ffc 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -2,371 +2,244 @@ * U-boot - Configuration file for BF533 STAMP board */ -#ifndef __CONFIG_STAMP_H__ -#define __CONFIG_STAMP_H__ +#ifndef __CONFIG_BF533_STAMP_H__ +#define __CONFIG_BF533_STAMP_H__ #include <asm/blackfin-config-pre.h> -#define CONFIG_RTC_BFIN 1 - -#define CONFIG_PANIC_HANG 1 - -#define CONFIG_BFIN_CPU bf533-0.3 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON /* - * Board settings + * Processor Settings */ -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x20300300 - -/* FLASH/ETHERNET uses the same address range */ -#define SHARED_RESOURCES 1 +#define CONFIG_BFIN_CPU bf533-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -/* Is I2C bit-banged? */ -#define CONFIG_SOFT_I2C 1 /* - * Software (bit-bang) I2C driver configuration + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV */ -#define PF_SCL PF3 -#define PF_SDA PF2 +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 11059200 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 45 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 -/* - * Video splash screen support - */ -#define CONFIG_VIDEO 0 /* - * Clock settings + * Memory Settings */ +#define CONFIG_MEM_ADD_WDTH 11 +#define CONFIG_MEM_SIZE 128 -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 11059200 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 36 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 - -/* - * Network settings - */ +#define CONFIG_EBIU_SDRRC_VAL 0x268 +#define CONFIG_EBIU_SDGCTL_VAL 0x911109 -#if (CONFIG_DRIVER_SMC91111) -#if 0 -#define CONFIG_MII -#endif +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 -/* network support */ -#define CONFIG_IPADDR 192.168.0.15 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 192.168.0.1 -#define CONFIG_SERVERIP 192.168.0.2 -#define CONFIG_HOSTNAME STAMP -#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) -/* To remove hardcoding and enable MAC storage in EEPROM */ -/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ -#endif /* CONFIG_DRIVER_SMC91111 */ /* - * Flash settings + * Network Settings */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20300300 +#define SMC91111_EEPROM_INIT() \ + do { \ + *pFIO_DIR |= PF1; \ + *pFIO_FLAG_S = PF1; \ + SSYNC(); \ + } while (0) +#define CONFIG_HOSTNAME bf533-stamp +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET - -#define CONFIG_SYS_FLASH_BASE 0x20000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */ -#else -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x20004000 -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#endif - -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */ -#define ENV_IS_EMBEDDED - -#define CONFIG_SYS_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */ -#define CONFIG_SYS_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ - -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11 - -/* - * following timeouts shall be used once the - * Flash real protection is enabled - */ -#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ - -/* - * SDRAM settings & memory map - */ - -#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC64M4A2FB_7E 1 - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MAX_RAM_SIZE - 0x80000 - 1) -#define CONFIG_LOADADDR 0x01000000 - -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - 0x40000) -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) - -/* Check to make sure everything fits in SDRAM */ -#if ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) > CONFIG_SYS_MAX_RAM_SIZE) - #error Memory Map does not fit into configuration -#endif - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif /* - * Command settings + * Flash Settings */ - -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 - -#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ - -/* configuration lookup from the BOOTP/DHCP server, */ -/* but not try to load any image using TFTP */ - -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ -#define CONFIG_BOOTCOMMAND "run ramboot" - -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" - - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ - "$(rootpath) console=ttyBF0,57600\0" \ - "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux; " \ - "run ramargs;run addip;bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux; " \ - "run nfsargs;run addip;bootelf\0" \ - "flashboot=bootm 0x20100000\0" \ - "update=tftpboot $(loadaddr) u-boot.bin; " \ - "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \ - "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ - "" - -#ifdef CONFIG_SOFT_I2C -#if (!CONFIG_SOFT_I2C) -#undef CONFIG_SOFT_I2C -#endif -#endif +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI_AMD_RESET +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 67 /* - * BOOTP options + * SPI Settings */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_HZ 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_WINBOND /* - * Command line configuration. + * Env Storage Settings */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DATE - -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_CMD_PING -#endif - -#if (CONFIG_SOFT_I2C) -#define CONFIG_CMD_I2C +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #endif - -#define CONFIG_CMD_DHCP - - -/* - * Console settings - */ - -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED #else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define ENV_IS_EMBEDDED_CUSTOM #endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_LOADS_ECHO 1 /* - * I2C settings + * I2C Settings * By default PF2 is used as SDA and PF3 as SCL on the Stamp board */ -#if (CONFIG_SOFT_I2C) - -#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") -#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") -#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") -#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") -#define I2C_SDA(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SDA; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SDA; \ - asm("ssync;"); \ - } -#define I2C_SCL(bit) if(bit) { \ - *pFIO_FLAG_S = PF_SCL; \ - asm("ssync;"); \ - } \ - else { \ - *pFIO_FLAG_C = PF_SCL; \ - asm("ssync;"); \ - } +#define CONFIG_SOFT_I2C +#ifdef CONFIG_SOFT_I2C +#define PF_SCL PF3 +#define PF_SDA PF2 +#define I2C_INIT \ + do { \ + *pFIO_DIR |= PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_ACTIVE \ + do { \ + *pFIO_DIR |= PF_SDA; \ + *pFIO_INEN &= ~PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_TRISTATE \ + do { \ + *pFIO_DIR &= ~PF_SDA; \ + *pFIO_INEN |= PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SDA; \ + else \ + *pFIO_FLAG_C = PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + *pFIO_FLAG_S = PF_SCL; \ + else \ + *pFIO_FLAG_C = PF_SCL; \ + SSYNC(); \ + } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_SYS_I2C_SLAVE 0 -#endif /* CONFIG_SOFT_I2C */ +#endif + /* - * Compact Flash settings + * Compact Flash / IDE / ATA Settings */ /* Enabled below option for CF support */ -/* #define CONFIG_STAMP_CF 1 */ - -#if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE) - -#define CONFIG_MISC_INIT_R 1 +/* #define CONFIG_STAMP_CF */ +#if defined(CONFIG_STAMP_CF) +#define CONFIG_MISC_INIT_R #define CONFIG_DOS_PARTITION 1 -/* - * IDE/ATA stuff - */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) #define CONFIG_SYS_ATA_BASE_ADDR 0x20200000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 + +#undef CONFIG_EBIU_AMBCTL1_VAL +#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 #endif + /* - * Miscellaneous configurable options + * Misc Settings */ +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 -#define CONFIG_SYS_HZ 1000 /* 1ms time tick */ - -#define CONFIG_SYS_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */ - -#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ +/* FLASH/ETHERNET uses the same async bank */ +#define SHARED_RESOURCES 1 -#define CONFIG_SPI +/* define to enable boot progress via leds */ +/* #define CONFIG_SHOW_BOOT_PROGRESS */ -#ifdef CONFIG_VIDEO -#if (CONFIG_VIDEO) -#define CONFIG_SPLASH_SCREEN 1 -#define CONFIG_SILENT_CONSOLE 1 -#else -#undef CONFIG_VIDEO +/* define to enable run status via led */ +/* #define CONFIG_STATUS_LED */ +#ifdef CONFIG_STATUS_LED +#define CONFIG_BOARD_SPECIFIC_LED +#ifndef __ASSEMBLY__ +typedef unsigned int led_id_t; +void __led_init(led_id_t mask, int state); +void __led_set(led_id_t mask, int state); +void __led_toggle(led_id_t mask); #endif +/* use LED1 to indicate booting/alive */ +#define STATUS_LED_BOOT 0 +#define STATUS_LED_BIT 1 +#define STATUS_LED_STATE STATUS_LED_ON +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) +/* use LED2 to indicate crash */ +#define STATUS_LED_CRASH 1 +#define STATUS_LED_BIT1 2 +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) #endif -/* - * FLASH organization and environment definitions - */ +/* define to enable splash screen support */ +/* #define CONFIG_VIDEO */ -#define CONFIG_EBIU_SDRRC_VAL 0x268 -#define CONFIG_EBIU_SDGCTL_VAL 0x911109 -#define CONFIG_EBIU_SDBCTL_VAL 0x37 -#define CONFIG_EBIU_AMGCTL_VAL 0xFF -#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 -#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 -#define CF_CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> #include <asm/blackfin-config-post.h> diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index f6399a9..3e5862d 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -2,272 +2,144 @@ * U-boot - Configuration file for BF537 STAMP board */ -#ifndef __CONFIG_BF537_H__ -#define __CONFIG_BF537_H__ +#ifndef __CONFIG_BF537_STAMP_H__ +#define __CONFIG_BF537_STAMP_H__ #include <asm/blackfin-config-pre.h> -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_BAUDRATE 57600 -/* Set default serial console for bf537 */ -#define CONFIG_UART_CONSOLE 0 -#define CONFIG_BOOTDELAY 5 -/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/ -/*#define CONFIG_BF537_STAMP_LEDCMD 1*/ - -#define CONFIG_PANIC_HANG 1 -#define CONFIG_BFIN_CPU bf537-0.2 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -#define CONFIG_BFIN_MAC +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf537-0.2 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON -/* Define if want to do post memory test */ -#undef CONFIG_POST_TEST - -#define CONFIG_RTC_BFIN 1 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ - -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 25000000 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL*/ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ -/* Values can range from 1-64 */ +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 25000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ #define CONFIG_VCO_MULT 20 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ #define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif - -#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC32M8A2_75 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 4 -#define CONFIG_LOADS_ECHO 1 /* - * rarpb, bootp or dhcp commands will perform only a - * configuration lookup from the BOOTP/DHCP server - * but not try to load any image using TFTP + * Memory Settings */ -#define CONFIG_SYS_AUTOLOAD "no" +#define CONFIG_MEM_ADD_WDTH 10 +#define CONFIG_MEM_SIZE 64 + +#define CONFIG_EBIU_SDRRC_VAL 0x306 +#define CONFIG_EBIU_SDGCTL_VAL 0x91114d + +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) + /* * Network Settings */ -/* network support */ -#ifdef CONFIG_BFIN_MAC -#define CONFIG_IPADDR 192.168.0.15 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 192.168.0.1 -#define CONFIG_SERVERIP 192.168.0.2 -#define CONFIG_HOSTNAME BF537 +#ifndef __ADSPBF534__ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_BFIN_MAC +#define CONFIG_NETCONSOLE 1 +#define CONFIG_NET_MULTI 1 #endif - -#define CONFIG_ROOTPATH /romfs +#define CONFIG_HOSTNAME bf537-stamp /* Uncomment next line to use fixed MAC address */ /* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ -/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */ - -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ -#define CONFIG_BOOTCOMMAND "run ramboot" - -#if defined(CONFIG_POST_TEST) -/* POST support */ -#define CONFIG_POST ( CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_FLASH | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_LED | \ - CONFIG_SYS_POST_BUTTON) -#else -#undef CONFIG_POST -#endif -#ifdef CONFIG_POST -#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ -#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ -#endif - -/* CF-CARD IDE-HDD Support */ - -/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */ -/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */ -/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */ - -#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE) -# define CONFIG_BFIN_IDE 1 -#endif - -/*#define CONFIG_BF537_NAND */ /* Add nand flash support */ - -#define CONFIG_NETCONSOLE 1 -#define CONFIG_NET_MULTI 1 /* - * BOOTP options + * Flash Settings */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */ +#define CONFIG_SYS_MAX_FLASH_SECT 71 /* - * Command line configuration. + * SPI Settings */ -#include <config_cmd_default.h> +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_HZ 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_WINBOND -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DATE -#ifndef CONFIG_BFIN_MAC -#undef CONFIG_CMD_NET +/* + * Env Storage Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #else -#define CONFIG_CMD_PING -#endif - -#if defined(CONFIG_BFIN_CF_IDE) \ - || defined(CONFIG_BFIN_HDD_IDE) \ - || defined(CONFIG_BFIN_TRUE_IDE) -#define CONFIG_CMD_IDE -#endif - -#define CONFIG_CMD_DHCP - -#if defined(CONFIG_POST) -#define CONFIG_CMD_DIAG -#endif - -#ifdef CONFIG_BF537_NAND -#define CONFIG_CMD_NAND +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #endif - - -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" -#define CONFIG_LOADADDR 0x1000000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux;" \ - "run ramargs;run addip;bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux;" \ - "run nfsargs;run addip;bootelf\0" \ - "flashboot=bootm 0x20100000\0" \ - "update=tftpboot $(loadaddr) u-boot.bin;" \ - "protect off 0x20000000 0x2007FFFF;" \ - "erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0" \ - "" - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED #else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define ENV_IS_EMBEDDED_CUSTOM #endif -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024*1024) -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR /* default load address */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_FLASH_BASE 0x20000000 -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 71 /* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */ -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) -#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */ -#else -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x20004000 -#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) -#endif -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */ -#define ENV_IS_EMBEDDED - -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 15 +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C 1 +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0 -#define CONFIG_SPI /* - * Stack sizes + * SPI_MMC Settings */ -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#define CONFIG_MMC +#define CONFIG_BFIN_SPI_MMC -#define POLL_MODE 1 -#define FLASH_TOT_SECT 71 -#define FLASH_SIZE 0x400000 -#define CONFIG_SYS_FLASH_SIZE 0x400000 /* - * Board NAND Infomation + * NAND Settings */ +/* #define CONFIG_BF537_NAND */ +#ifdef CONFIG_BF537_NAND +# define CONFIG_CMD_NAND +#endif #define CONFIG_SYS_NAND_ADDR 0x20212000 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_NAND_ADDR @@ -280,56 +152,35 @@ #define NAND_MAX_FLOORS 1 #define BFIN_NAND_READY PF3 -#define NAND_WAIT_READY(nand) \ - do { \ - int timeout = 0; \ - while(!(*pPORTFIO & PF3)) \ - if (timeout++ > 100000) \ - break; \ +#define NAND_WAIT_READY(nand) \ + do { \ + int timeout = 0; \ + while (!(*pPORTFIO & PF3)) \ + if (timeout++ > 100000) \ + break; \ } while (0) -#define BFIN_NAND_CLE (1<<2) /* A2 -> Command Enable */ -#define BFIN_NAND_ALE (1<<1) /* A1 -> Address Enable */ - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) - -/* - * Initialize PSD4256 registers for using I2C - */ -#define CONFIG_MISC_INIT_R +#define BFIN_NAND_CLE (1 << 2) /* A2 -> Command Enable */ +#define BFIN_NAND_ALE (1 << 1) /* A1 -> Address Enable */ +#define WRITE_NAND_COMMAND(d, adr) bfin_write8(adr | BFIN_NAND_CLE, d) +#define WRITE_NAND_ADDRESS(d, adr) bfin_write8(adr | BFIN_NAND_ALE, d) +#define WRITE_NAND(d, adr) bfin_write8(adr, d) +#define READ_NAND(adr) bfin_read8(adr) -#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ /* - * I2C settings + * CF-CARD IDE-HDD Support */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_BFIN_TWI_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 - -#define CONFIG_EBIU_SDRRC_VAL 0x306 -#define CONFIG_EBIU_SDGCTL_VAL 0x91114d -#define CONFIG_EBIU_SDBCTL_VAL 0x25 - -#define CONFIG_EBIU_AMGCTL_VAL 0xFF -#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 -#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 - -/* 0xFF, 0x7BB07BB0, 0x22547BB0 */ -/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN) -#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \ - ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN) -#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \ - B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN) -*/ +/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */ +/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */ +/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */ -#define AMGCTLVAL 0xFF -#define AMBCTL0VAL 0x7BB07BB0 -#define AMBCTL1VAL 0xFFC27BB0 +#if defined(CONFIG_BFIN_CF_IDE) || \ + defined(CONFIG_BFIN_HDD_IDE) || \ + defined(CONFIG_BFIN_TRUE_IDE) +# define CONFIG_BFIN_IDE 1 +# define CONFIG_CMD_IDE +#endif #if defined(CONFIG_BFIN_IDE) @@ -341,11 +192,11 @@ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) -#undef AMBCTL1VAL -#define AMBCTL1VAL 0xFFC3FFC3 +#undef CONFIG_EBIU_AMBCTL1_VAL +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3 #define CONFIG_CF_ATASEL_DIS 0x20311800 #define CONFIG_CF_ATASEL_ENA 0x20311802 @@ -357,34 +208,54 @@ */ #define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.Ax */ -#endif /* CONFIG_BFIN_TRUE_IDE */ -#if defined(CONFIG_BFIN_CF_IDE) /* USE CompactFlash Storage Card in the common memory space */ +#elif defined(CONFIG_BFIN_CF_IDE) #define CONFIG_SYS_ATA_BASE_ADDR 0x20211800 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 1 /* CF.A0 --> Blackfin.Ax */ -#endif /* CONFIG_BFIN_CF_IDE */ -#if defined(CONFIG_BFIN_HDD_IDE) /* USE TRUE IDE */ +#elif defined(CONFIG_BFIN_HDD_IDE) #define CONFIG_SYS_ATA_BASE_ADDR 0x20314000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */ - #undef CONFIG_SCLK_DIV #define CONFIG_SCLK_DIV 8 -#endif /* CONFIG_BFIN_HDD_IDE */ +#endif + +#endif -#endif /*CONFIG_BFIN_IDE */ + +/* + * Misc Settings + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 + +/* #define CONFIG_BF537_STAMP_LEDCMD 1 */ + +/* Define if want to do post memory test */ +#undef CONFIG_POST +#ifdef CONFIG_POST +#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ +#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ +#endif + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> #include <asm/blackfin-config-post.h> diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h index 320a8c6..ef2019f 100644 --- a/include/configs/bf561-ezkit.h +++ b/include/configs/bf561-ezkit.h @@ -2,229 +2,152 @@ * U-boot - Configuration file for BF561 EZKIT board */ -#ifndef __CONFIG_EZKIT561_H__ -#define __CONFIG_EZKIT561_H__ +#ifndef __CONFIG_BF561_EZKIT_H__ +#define __CONFIG_BF561_EZKIT_H__ #include <asm/blackfin-config-pre.h> -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_BAUDRATE 57600 -/* Set default serial console for bf537 */ -#define CONFIG_UART_CONSOLE 0 -#define CONFIG_EZKIT561 1 -#define CONFIG_BOOTDELAY 5 - -#define CONFIG_PANIC_HANG 1 - -#define CONFIG_BFIN_CPU bf561-0.3 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - -/* This sets the default state of the cache on U-Boot's boot */ -#define CONFIG_ICACHE_ON -#define CONFIG_DCACHE_ON /* - * Board settings + * Processor Settings */ -#define CONFIG_DRIVER_SMC91111 1 -#define CONFIG_SMC91111_BASE 0x2C010300 -#define CONFIG_ASYNC_EBIU_BASE CONFIG_SMC91111_BASE & ~(4*1024*1024) -#define CONFIG_SMC_USE_32_BIT 1 -#define CONFIG_MISC_INIT_R 1 - -/* - * Clock settings - */ - -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 30000000 -/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ -/* 1=CLKIN/2 */ -#define CONFIG_CLKIN_HALF 0 -/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ -/* 1=bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* CONFIG_VCO_MULT controls what the multiplier of the PLL is */ -/* Values can range from 1-64 */ -#define CONFIG_VCO_MULT 20 -/* CONFIG_CCLK_DIV controls what the core clock divider is */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 5 -/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ -/* Values can range from 2-65535 */ -/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ -#define CONFIG_SPI_BAUD 2 -#define CONFIG_SPI_BAUD_INITBLOCK 4 +#define CONFIG_BFIN_CPU bf561-0.3 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS -/* - * Network settings - */ -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_IPADDR 192.168.0.15 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_GATEWAYIP 192.168.0.1 -#define CONFIG_SERVERIP 192.168.0.2 -#define CONFIG_HOSTNAME ezkit561 -#define CONFIG_ROOTPATH /arm-cross-build/BF561/uClinux-dist/romfs -#endif /* CONFIG_DRIVER_SMC91111 */ /* - * Flash settings + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 30000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 20 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 6 -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_SYS_FLASH_BASE 0x20000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max number of sectors on one chip */ -#define CONFIG_ENV_ADDR 0x20020000 -#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 8 /* - * SDRAM settings & memory map + * Memory Settings */ +#define CONFIG_MEM_ADD_WDTH 9 +#define CONFIG_MEM_SIZE 64 -#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ -#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ -#define CONFIG_MEM_MT48LC16M16A2TG_75 1 - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024) - -#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */ +#define CONFIG_EBIU_SDRRC_VAL 0x306 +#define CONFIG_EBIU_SDGCTL_VAL 0x91114d -#define CONFIG_LOADADDR 0x01000000 /* default load address */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN) +#define CONFIG_EBIU_AMGCTL_VAL 0x3F +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) -#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) -#define CONFIG_STACKSIZE (128*1024) /* regular stack */ - -#if ( CONFIG_CLKIN_HALF == 0 ) -#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) -#else -#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) -#endif - -#if (CONFIG_PLL_BYPASS == 0) -#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) -#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) -#else -#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ -#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ -#endif /* - * Command settings + * Network Settings */ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x2C010300 +#define CONFIG_SMC_USE_32_BIT 1 +#define CONFIG_HOSTNAME bf561-ezkit +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ -#define CONFIG_SYS_AUTOLOAD "no" /* rarpb, bootp, dhcp commands will */ - /* only perform a configuration */ - /* lookup from the BOOTP/DHCP server */ - /* but not try to load any image */ - /* using TFTP */ -#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, */ - /* currently its disabled */ -#define CONFIG_BOOTCOMMAND "run ramboot" -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" - -#if (CONFIG_DRIVER_SMC91111) -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ - "$(rootpath) console=ttyBF0,57600\0" \ - "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ - "ramboot=tftpboot $(loadaddr) linux; " \ - "run ramargs; run addip; bootelf\0" \ - "nfsboot=tftpboot $(loadaddr) linux; " \ - "run nfsargs; run addip; bootelf\0" \ - "update=tftpboot $(loadaddr) u-boot.bin; " \ - "protect off 0x20000000 0x2003FFFF; " \ - "erase 0x20000000 0x2003FFFF; " \ - "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ - "" -#else -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ - "flashboot=bootm 0x20100000\0" \ - "" -#endif - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME /* - * Command line configuration. + * Flash Settings */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_JFFS2 - -#if defined(CONFIG_DRIVER_SMC91111) -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI_AMD_RESET +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 135 +/* The BF561-EZKIT uses a top boot flash */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR 0x20004000 +#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED +#else +#define ENV_IS_EMBEDDED_CUSTOM #endif + /* - * Console settings + * I2C Settings */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SOFT_I2C +#ifdef CONFIG_SOFT_I2C +#define PF_SCL PF0 +#define PF_SDA PF1 +#define I2C_INIT \ + do { \ + *pFIO0_DIR |= PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_ACTIVE \ + do { \ + *pFIO0_DIR |= PF_SDA; \ + *pFIO0_INEN &= ~PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_TRISTATE \ + do { \ + *pFIO0_DIR &= ~PF_SDA; \ + *pFIO0_INEN |= PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + *pFIO0_FLAG_S = PF_SDA; \ + else \ + *pFIO0_FLAG_C = PF_SDA; \ + SSYNC(); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + *pFIO0_FLAG_S = PF_SCL; \ + else \ + *pFIO0_FLAG_C = PF_SCL; \ + SSYNC(); \ + } while (0) +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0 #endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_LOADS_ECHO 1 /* - * Miscellaneous configurable options + * Misc Settings */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */ -#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ +#define CONFIG_UART_CONSOLE 0 + /* - * FLASH organization and environment definitions + * Pull in common ADI header for remaining command/environment setup */ -#define CONFIG_EBIU_SDRRC_VAL 0x306 -#define CONFIG_EBIU_SDGCTL_VAL 0x91114d -#define CONFIG_EBIU_SDBCTL_VAL 0x15 - -#define CONFIG_EBIU_AMGCTL_VAL 0x3F -#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 -#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 +#include <configs/bfin_adi_common.h> #include <asm/blackfin-config-post.h> diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h new file mode 100644 index 0000000..bfe5376 --- /dev/null +++ b/include/configs/bfin_adi_common.h @@ -0,0 +1,199 @@ +/* + * U-Boot - Common settings for Analog Devices boards + */ + +#ifndef __CONFIG_BFIN_ADI_COMMON_H__ +#define __CONFIG_BFIN_ADI_COMMON_H__ + +/* + * Command Settings + */ +#ifndef _CONFIG_CMD_DEFAULT_H +# include <config_cmd_default.h> +# if ADI_CMDS_NETWORK +# define CONFIG_CMD_DHCP +# define CONFIG_CMD_PING +# ifdef CONFIG_BFIN_MAC +# define CONFIG_CMD_MII +# endif +# else +# undef CONFIG_CMD_BOOTD +# undef CONFIG_CMD_NET +# undef CONFIG_CMD_NFS +# endif +# ifdef CONFIG_LIBATA +# define CONFIG_CMD_FAT +# define CONFIG_CMD_SATA +# define CONFIG_DOS_PARTITION +# endif +# ifdef CONFIG_MMC +# define CONFIG_CMD_FAT +# define CONFIG_CMD_MMC +# define CONFIG_DOS_PARTITION +# endif +# ifdef CONFIG_USB +# define CONFIG_CMD_EXT2 +# define CONFIG_CMD_FAT +# define CONFIG_CMD_USB +# define CONFIG_CMD_USB_STORAGE +# define CONFIG_DOS_PARTITION +# endif +# ifdef CONFIG_POST +# define CONFIG_CMD_DIAG +# endif +# ifdef CONFIG_RTC_BFIN +# define CONFIG_CMD_DATE +# endif +# ifdef CONFIG_SPI +# define CONFIG_CMD_EEPROM +# endif +# if defined(CONFIG_BFIN_SPI) || defined(CONFIG_SOFT_SPI) +# define CONFIG_CMD_SPI +# endif +# ifdef CONFIG_SPI_FLASH +# define CONFIG_CMD_SF +# endif +# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +# define CONFIG_CMD_I2C +# endif +# ifdef CONFIG_SYS_NO_FLASH +# undef CONFIG_CMD_FLASH +# undef CONFIG_CMD_IMLS +# else +# define CONFIG_CMD_JFFS2 +# endif +# define CONFIG_CMD_BOOTLDR +# define CONFIG_CMD_CACHE +# define CONFIG_CMD_CPLBINFO +# define CONFIG_CMD_ELF +# define CONFIG_ELF_SIMPLE_LOAD +# define CONFIG_CMD_REGINFO +# define CONFIG_CMD_STRINGS +# if defined(__ADSPBF51x__) || defined(__ADSPBF52x__) || defined(__ADSPBF54x__) +# define CONFIG_CMD_OTP +# endif +#endif + +/* + * Console Settings + */ +#define CONFIG_SYS_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE 1 +#define CONFIG_LOADS_ECHO 1 +#define CONFIG_JTAG_CONSOLE +#ifndef CONFIG_BAUDRATE +# define CONFIG_BAUDRATE 57600 +#endif + +/* + * Debug Settings + */ +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_DEBUG_DUMP 1 +#define CONFIG_DEBUG_DUMP_SYMS 1 +#define CONFIG_PANIC_HANG 1 + +/* + * Env Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) +# define CONFIG_BOOTDELAY -1 +#else +# define CONFIG_BOOTDELAY 5 +#endif +#define CONFIG_BOOTCOMMAND "run ramboot" +#ifdef CONFIG_VIDEO +# define CONFIG_BOOTARGS_VIDEO "console=tty0 " +#else +# define CONFIG_BOOTARGS_VIDEO "" +#endif +#define CONFIG_BOOTARGS \ + "root=/dev/mtdblock0 rw " \ + "clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \ + "earlyprintk=" \ + "serial," \ + "uart" MK_STR(CONFIG_UART_CONSOLE) "," \ + MK_STR(CONFIG_BAUDRATE) " " \ + CONFIG_BOOTARGS_VIDEO \ + "console=ttyBF0," MK_STR(CONFIG_BAUDRATE) + +#if defined(CONFIG_CMD_NET) +# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +# define UBOOT_ENV_FILE "u-boot.bin" +# else +# define UBOOT_ENV_FILE "u-boot.ldr" +# endif +# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +# ifdef CONFIG_SPI +# define UBOOT_ENV_UPDATE \ + "eeprom write $(loadaddr) 0x0 $(filesize)" +# else +# define UBOOT_ENV_UPDATE \ + "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \ + "sf erase 0 0x40000;" \ + "sf write $(loadaddr) 0 $(filesize)" +# endif +# elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND) +# define UBOOT_ENV_UPDATE \ + "nand unlock 0 0x40000;" \ + "nand erase 0 0x40000;" \ + "nand write $(loadaddr) 0 0x40000" +# else +# define UBOOT_ENV_UPDATE \ + "protect off 0x20000000 0x2003FFFF;" \ + "erase 0x20000000 0x2003FFFF;" \ + "cp.b $(loadaddr) 0x20000000 $(filesize)" +# endif +# define NETWORK_ENV_SETTINGS \ + "ubootfile=" UBOOT_ENV_FILE "\0" \ + "update=" \ + "tftp $(loadaddr) $(ubootfile);" \ + UBOOT_ENV_UPDATE \ + "\0" \ + "addip=set bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \ + "$(hostname):eth0:off" \ + "\0" \ + "ramargs=set bootargs " CONFIG_BOOTARGS "\0" \ + "ramboot=" \ + "tftp $(loadaddr) uImage;" \ + "run ramargs;" \ + "run addip;" \ + "bootm" \ + "\0" \ + "nfsargs=set bootargs " \ + "root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \ + "\0" \ + "nfsboot=" \ + "tftp $(loadaddr) vmImage;" \ + "run nfsargs;" \ + "run addip;" \ + "bootm" \ + "\0" +#else +# define NETWORK_ENV_SETTINGS +#endif +#define CONFIG_EXTRA_ENV_SETTINGS \ + NETWORK_ENV_SETTINGS \ + "flashboot=bootm 0x20100000\0" + +/* + * Network Settings + */ +#ifdef CONFIG_CMD_NET +# define CONFIG_IPADDR 192.168.0.15 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_GATEWAYIP 192.168.0.1 +# define CONFIG_SERVERIP 192.168.0.2 +# define CONFIG_ROOTPATH /romfs +# ifdef CONFIG_CMD_DHCP +# ifndef CONFIG_SYS_AUTOLOAD +# define CONFIG_SYS_AUTOLOAD "no" +# endif +# endif +# define CONFIG_NET_RETRY_COUNT 20 +#endif + +#endif diff --git a/lib_blackfin/board.c b/lib_blackfin/board.c index 537f69a..49465d2 100644 --- a/lib_blackfin/board.c +++ b/lib_blackfin/board.c @@ -291,6 +291,25 @@ void board_init_f(ulong bootflag) board_init_r((gd_t *) gd, 0x20000010); } +static void board_net_init_r(bd_t *bd) +{ +#ifdef CONFIG_CMD_NET + uchar enetaddr[6]; + char *s; + + if ((s = getenv("bootfile")) != NULL) + copy_filename(BootFile, s, sizeof(BootFile)); + + bd->bi_ip_addr = getenv_IPaddr("ipaddr"); + + printf("Net: "); + eth_initialize(gd->bd); + + eth_getenv_enetaddr("ethaddr", enetaddr); + printf("MAC: %pM\n", enetaddr); +#endif +} + void board_init_r(gd_t * id, ulong dest_addr) { extern void malloc_bin_reloc(void); @@ -308,8 +327,8 @@ void board_init_r(gd_t * id, ulong dest_addr) #if !defined(CONFIG_SYS_NO_FLASH) /* Initialize the flash and protect u-boot by default */ extern flash_info_t flash_info[]; - ulong size = flash_init(); puts("Flash: "); + ulong size = flash_init(); print_size(size, "\n"); flash_protect(FLAG_PROTECT_SET, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - 1, @@ -349,22 +368,13 @@ void board_init_r(gd_t * id, ulong dest_addr) /* Initialize from environment */ if ((s = getenv("loadaddr")) != NULL) load_addr = simple_strtoul(s, NULL, 16); -#ifdef CONFIG_CMD_NET - if ((s = getenv("bootfile")) != NULL) - copy_filename(BootFile, s, sizeof(BootFile)); -#endif #if defined(CONFIG_MISC_INIT_R) /* miscellaneous platform dependent initialisations */ misc_init_r(); #endif -#ifdef CONFIG_CMD_NET - /* IP Address */ - bd->bi_ip_addr = getenv_IPaddr("ipaddr"); - printf("Net: "); - eth_initialize(gd->bd); -#endif + board_net_init_r(bd); display_global_data(); diff --git a/lib_blackfin/cache.c b/lib_blackfin/cache.c index 1557864..0a321a4 100644 --- a/lib_blackfin/cache.c +++ b/lib_blackfin/cache.c @@ -36,6 +36,44 @@ void flush_cache(unsigned long addr, unsigned long size) blackfin_dcache_flush_range(start_addr, end_addr); } +#ifdef CONFIG_DCACHE_WB +static void flushinv_all_dcache(void) +{ + u32 way, bank, subbank, set; + u32 status, addr; + u32 dmem_ctl = bfin_read_DMEM_CONTROL(); + + for (bank = 0; bank < 2; ++bank) { + if (!(dmem_ctl & (1 << (DMC1_P - bank)))) + continue; + + for (way = 0; way < 2; ++way) + for (subbank = 0; subbank < 4; ++subbank) + for (set = 0; set < 64; ++set) { + + bfin_write_DTEST_COMMAND( + way << 26 | + bank << 23 | + subbank << 16 | + set << 5 + ); + CSYNC(); + status = bfin_read_DTEST_DATA0(); + + /* only worry about valid/dirty entries */ + if ((status & 0x3) != 0x3) + continue; + + /* construct the address using the tag */ + addr = (status & 0xFFFFC800) | (subbank << 12) | (set << 5); + + /* flush it */ + __asm__ __volatile__("FLUSHINV[%0];" : : "a"(addr)); + } + } +} +#endif + void icache_enable(void) { bfin_write_IMEM_CONTROL(IMC | ENICPLB); @@ -61,6 +99,10 @@ void dcache_enable(void) void dcache_disable(void) { +#ifdef CONFIG_DCACHE_WB + bfin_write_DMEM_CONTROL(bfin_read_DMEM_CONTROL() & ~(ENDCPLB)); + flushinv_all_dcache(); +#endif bfin_write_DMEM_CONTROL(0); SSYNC(); } |