diff options
| -rw-r--r-- | board/mbx8xx/pcmcia.c | 4 | ||||
| -rw-r--r-- | board/tqc/tqm8xx/tqm8xx.c | 23 | ||||
| -rw-r--r-- | boards.cfg | 1 | ||||
| -rw-r--r-- | common/cmd_ide.c | 11 | ||||
| -rw-r--r-- | drivers/input/ps2ser.c | 109 | ||||
| -rw-r--r-- | drivers/pcmcia/mpc8xx_pcmcia.c | 29 | ||||
| -rw-r--r-- | drivers/pcmcia/tqm8xx_pcmcia.c | 42 | ||||
| -rw-r--r-- | include/configs/HMI10.h | 504 | ||||
| -rw-r--r-- | include/status_led.h | 17 |
9 files changed, 23 insertions, 717 deletions
diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c index 69368d8..e672d8c 100644 --- a/board/mbx8xx/pcmcia.c +++ b/board/mbx8xx/pcmcia.c @@ -117,11 +117,7 @@ int pcmcia_hardware_enable (int slot) debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__, &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); -#ifndef CONFIG_HMI10 - if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { -#else if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) { -#endif /* CONFIG_HMI10 */ printf (" No Card found\n"); return (1); } diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c index cde780b..940cc8f 100644 --- a/board/tqc/tqm8xx/tqm8xx.c +++ b/board/tqc/tqm8xx/tqm8xx.c @@ -430,29 +430,6 @@ static long int dram_size (long int mamr_value, long int *base, long int maxsize /* ------------------------------------------------------------------------- */ -#ifdef CONFIG_PS2MULT - -#ifdef CONFIG_HMI10 -#define BASE_BAUD ( 1843200 / 16 ) -struct serial_state rs_table[] = { - { BASE_BAUD, 4, (void*)0xec140000 }, - { BASE_BAUD, 2, (void*)0xec150000 }, - { BASE_BAUD, 6, (void*)0xec160000 }, - { BASE_BAUD, 10, (void*)0xec170000 }, -}; - -#ifdef CONFIG_BOARD_EARLY_INIT_R -int board_early_init_r (void) -{ - ps2mult_early_init(); - return (0); -} -#endif -#endif /* CONFIG_HMI10 */ - -#endif /* CONFIG_PS2MULT */ - - #ifdef CONFIG_MISC_INIT_R extern void load_sernum_ethaddr(void); int misc_init_r (void) @@ -170,7 +170,6 @@ QS823 powerpc mpc8xx qs850 snmc QS850 powerpc mpc8xx qs850 snmc QS860T powerpc mpc8xx qs860t snmc stxxtc powerpc mpc8xx stxxtc stx -HMI10 powerpc mpc8xx tqm8xx tqc SM850 powerpc mpc8xx tqm8xx tqc AMX860 powerpc mpc8xx amx860 westel csb272 powerpc ppc4xx diff --git a/common/cmd_ide.c b/common/cmd_ide.c index 6aeca76..ea0f4a7 100644 --- a/common/cmd_ide.c +++ b/common/cmd_ide.c @@ -818,7 +818,7 @@ set_pcmcia_timing (int pmode) static void input_swap_data(int dev, ulong *sect_buf, int words) { -#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45) +#if defined(CONFIG_CPC45) uchar i; volatile uchar *pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN); volatile uchar *pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD); @@ -858,7 +858,7 @@ input_swap_data(int dev, ulong *sect_buf, int words) static void output_data(int dev, ulong *sect_buf, int words) { -#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45) +#if defined(CONFIG_CPC45) uchar *dbuf; volatile uchar *pbuf_even; volatile uchar *pbuf_odd; @@ -910,7 +910,7 @@ output_data(int dev, ulong *sect_buf, int words) static void input_data(int dev, ulong *sect_buf, int words) { -#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45) +#if defined(CONFIG_CPC45) uchar *dbuf; volatile uchar *pbuf_even; volatile uchar *pbuf_odd; @@ -1544,7 +1544,6 @@ static void ide_reset (void) #if defined(CONFIG_IDE_LED) && \ !defined(CONFIG_CPC45) && \ - !defined(CONFIG_HMI10) && \ !defined(CONFIG_KUP4K) && \ !defined(CONFIG_KUP4X) @@ -1586,7 +1585,7 @@ int ide_device_present(int dev) static void output_data_shorts(int dev, ushort *sect_buf, int shorts) { -#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45) +#if defined(CONFIG_CPC45) uchar *dbuf; volatile uchar *pbuf_even; volatile uchar *pbuf_odd; @@ -1618,7 +1617,7 @@ output_data_shorts(int dev, ushort *sect_buf, int shorts) static void input_data_shorts(int dev, ushort *sect_buf, int shorts) { -#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45) +#if defined(CONFIG_CPC45) uchar *dbuf; volatile uchar *pbuf_even; volatile uchar *pbuf_odd; diff --git a/drivers/input/ps2ser.c b/drivers/input/ps2ser.c index 8d0b6d6..a655a16 100644 --- a/drivers/input/ps2ser.c +++ b/drivers/input/ps2ser.c @@ -46,8 +46,7 @@ DECLARE_GLOBAL_DATA_PTR; #error CONFIG_PS2SERIAL must be in 1 ... 6 #endif -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) +#else #if CONFIG_PS2SERIAL == 1 #define COM_BASE (CONFIG_SYS_CCSRBAR+0x4500) @@ -57,17 +56,12 @@ DECLARE_GLOBAL_DATA_PTR; #error CONFIG_PS2SERIAL must be in 1 ... 2 #endif -#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */ +#endif /* CONFIG_MPC5xxx / other */ static int ps2ser_getc_hw(void); static void ps2ser_interrupt(void *dev_id); extern struct serial_state rs_table[]; /* in serial.c */ -#if !defined(CONFIG_MPC5xxx) && !defined(CONFIG_MPC8540) && \ - !defined(CONFIG_MPC8541) && !defined(CONFIG_MPC8548) && \ - !defined(CONFIG_MPC8555) -static struct serial_state *state; -#endif static u_char ps2buf[PS2BUF_SIZE]; static atomic_t ps2buf_cnt; @@ -111,8 +105,8 @@ int ps2ser_init(void) return (0); } -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) +#else + int ps2ser_init(void) { NS16550_t com_port = (NS16550_t)COM_BASE; @@ -128,76 +122,24 @@ int ps2ser_init(void) return (0); } -#else /* !CONFIG_MPC5xxx && !CONFIG_MPC8540 / other */ - -static inline unsigned int ps2ser_in(int offset) -{ - return readb((unsigned long) state->iomem_base + offset); -} - -static inline void ps2ser_out(int offset, int value) -{ - writeb(value, (unsigned long) state->iomem_base + offset); -} - -int ps2ser_init(void) -{ - int quot; - unsigned cval; - - state = rs_table + CONFIG_PS2SERIAL; - - quot = state->baud_base / PS2SER_BAUD; - cval = 0x3; /* 8N1 - 8 data bits, no parity bits, 1 stop bit */ - - /* Set speed, enable interrupts, enable FIFO - */ - ps2ser_out(UART_LCR, cval | UART_LCR_DLAB); - ps2ser_out(UART_DLL, quot & 0xff); - ps2ser_out(UART_DLM, quot >> 8); - ps2ser_out(UART_LCR, cval); - ps2ser_out(UART_IER, UART_IER_RDI); - ps2ser_out(UART_MCR, UART_MCR_OUT2 | UART_MCR_DTR | UART_MCR_RTS); - ps2ser_out(UART_FCR, - UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); - - /* If we read 0xff from the LSR, there is no UART here - */ - if (ps2ser_in(UART_LSR) == 0xff) { - printf ("ps2ser.c: no UART found\n"); - return -1; - } - - irq_install_handler(state->irq, ps2ser_interrupt, NULL); - - return 0; -} -#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */ +#endif /* CONFIG_MPC5xxx / other */ void ps2ser_putc(int chr) { #ifdef CONFIG_MPC5xxx volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE; -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) +#else NS16550_t com_port = (NS16550_t)COM_BASE; #endif -#ifdef DEBUG - printf(">>>> 0x%02x\n", chr); -#endif + debug(">>>> 0x%02x\n", chr); #ifdef CONFIG_MPC5xxx while (!(psc->psc_status & PSC_SR_TXRDY)); psc->psc_buffer_8 = chr; -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) +#else while ((com_port->lsr & UART_LSR_THRE) == 0); com_port->thr = chr; -#else - while (!(ps2ser_in(UART_LSR) & UART_LSR_THRE)); - - ps2ser_out(UART_TX, chr); #endif } @@ -205,8 +147,7 @@ static int ps2ser_getc_hw(void) { #ifdef CONFIG_MPC5xxx volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE; -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) +#else NS16550_t com_port = (NS16550_t)COM_BASE; #endif int res = -1; @@ -215,15 +156,10 @@ static int ps2ser_getc_hw(void) if (psc->psc_status & PSC_SR_RXRDY) { res = (psc->psc_buffer_8); } -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) +#else if (com_port->lsr & UART_LSR_DR) { res = com_port->rbr; } -#else - if (ps2ser_in(UART_LSR) & UART_LSR_DR) { - res = (ps2ser_in(UART_RX)); - } #endif return res; @@ -234,9 +170,7 @@ int ps2ser_getc(void) volatile int chr; int flags; -#ifdef DEBUG - printf("<< "); -#endif + debug("<< "); flags = disable_interrupts(); @@ -251,11 +185,10 @@ int ps2ser_getc(void) } while (chr < 0); - if (flags) enable_interrupts(); + if (flags) + enable_interrupts(); -#ifdef DEBUG - printf("0x%02x\n", chr); -#endif + debug("0x%02x\n", chr); return chr; } @@ -275,8 +208,7 @@ static void ps2ser_interrupt(void *dev_id) { #ifdef CONFIG_MPC5xxx volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE; -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) +#else NS16550_t com_port = (NS16550_t)COM_BASE; #endif int chr; @@ -286,11 +218,8 @@ static void ps2ser_interrupt(void *dev_id) chr = ps2ser_getc_hw(); #ifdef CONFIG_MPC5xxx status = psc->psc_status; -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) - status = com_port->lsr; #else - status = ps2ser_in(UART_IIR); + status = com_port->lsr; #endif if (chr < 0) continue; @@ -303,13 +232,9 @@ static void ps2ser_interrupt(void *dev_id) } #ifdef CONFIG_MPC5xxx } while (status & PSC_SR_RXRDY); -#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \ - defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555) - } while (status & UART_LSR_DR); #else - } while (status & UART_IIR_RDI); + } while (status & UART_LSR_DR); #endif - if (atomic_read(&ps2buf_cnt)) { ps2mult_callback(atomic_read(&ps2buf_cnt)); } diff --git a/drivers/pcmcia/mpc8xx_pcmcia.c b/drivers/pcmcia/mpc8xx_pcmcia.c index 7030574..74a50f1 100644 --- a/drivers/pcmcia/mpc8xx_pcmcia.c +++ b/drivers/pcmcia/mpc8xx_pcmcia.c @@ -57,12 +57,6 @@ static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] = /* -------------------------------------------------------------------- */ -#ifdef CONFIG_HMI10 -#define HMI10_FRAM_TIMING ( PCMCIA_SHT(2) \ - | PCMCIA_SST(2) \ - | PCMCIA_SL(4)) -#endif - #if defined(CONFIG_LWMON) || defined(CONFIG_NSCU) #define CONFIG_SYS_PCMCIA_TIMING ( PCMCIA_SHT(9) \ | PCMCIA_SST(3) \ @@ -106,17 +100,6 @@ int pcmcia_on (void) switch (i) { #ifdef CONFIG_IDE_8xx_PCCARD case 4: -#ifdef CONFIG_HMI10 - { /* map FRAM area */ - win->or = ( PCMCIA_BSIZE_256K - | PCMCIA_PPS_8 - | PCMCIA_PRS_ATTR - | slotbit - | PCMCIA_PV - | HMI10_FRAM_TIMING ); - break; - } -#endif case 0: { /* map attribute memory */ win->or = ( PCMCIA_BSIZE_64M | PCMCIA_PPS_8 @@ -147,18 +130,6 @@ int pcmcia_on (void) break; } #endif /* CONFIG_IDE_8xx_PCCARD */ -#ifdef CONFIG_HMI10 - case 3: { /* map I/O window for 4xUART data/ctrl */ - win->br += 0x40000; - win->or = ( PCMCIA_BSIZE_256K - | PCMCIA_PPS_8 - | PCMCIA_PRS_IO - | slotbit - | PCMCIA_PV - | CONFIG_SYS_PCMCIA_TIMING ); - break; - } -#endif /* CONFIG_HMI10 */ default: /* set to not valid */ win->or = 0; break; diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c index 6ba8b5c..ca1a9fe 100644 --- a/drivers/pcmcia/tqm8xx_pcmcia.c +++ b/drivers/pcmcia/tqm8xx_pcmcia.c @@ -36,39 +36,6 @@ #define power_on_5_0(slot) do {} while (0) #define power_on_3_3(slot) do {} while (0) -#elif defined(CONFIG_HMI10) - -static inline void power_config(int slot) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - /* - * Configure Port B pins for - * 5 Volts Enable and 3 Volts enable - */ - immap->im_cpm.cp_pbpar &= ~(0x00000300); -} - -static inline void power_off(int slot) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - /* remove all power */ - immap->im_cpm.cp_pbdat |= 0x00000300; -} - -static inline void power_on_5_0(int slot) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - immap->im_cpm.cp_pbdat &= ~(0x0000100); - immap->im_cpm.cp_pbdir |= 0x00000300; -} - -static inline void power_on_3_3(int slot) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - immap->im_cpm.cp_pbdat &= ~(0x0000200); - immap->im_cpm.cp_pbdir |= 0x00000300; -} - #elif defined(CONFIG_VIRTLAB2) #define power_config(slot) do {} while (0) @@ -128,21 +95,12 @@ static inline void power_on_3_3(int slot) #endif -#ifdef CONFIG_HMI10 -static inline int check_card_is_absent(int slot) -{ - volatile pcmconf8xx_t *pcmp = - (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); - return pcmp->pcmc_pipr & (0x10000000 >> (slot << 4)); -} -#else static inline int check_card_is_absent(int slot) { volatile pcmconf8xx_t *pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia)); return pcmp->pcmc_pipr & (0x18000000 >> (slot << 4)); } -#endif #ifdef NSCU_OE_INV #define NSCU_GCRX_CXOE 0 diff --git a/include/configs/HMI10.h b/include/configs/HMI10.h deleted file mode 100644 index 2747d8c..0000000 --- a/include/configs/HMI10.h +++ /dev/null @@ -1,504 +0,0 @@ -/* - * (C) Copyright 2000-2008 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_HMI10 -#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ -#define CONFIG_TQM823L 1 /* ...on a TQM8xxL module */ - -#define CONFIG_LCD -#define CONFIG_NEC_NL6448BC33_54 /* NEC NL6448BC33_54 display */ - -#ifdef CONFIG_LCD /* with LCD controller ? */ -#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ -#endif - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#define CONFIG_SYS_SMC_RXBUFLEN 128 -#define CONFIG_SYS_MAXIDLE 10 -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ - -#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ -#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ -#define CONFIG_PS2SERIAL 2 /* .. on COM3 */ -#define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ - -#define CONFIG_BOOTCOUNT_LIMIT - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_BOARD_TYPES 1 /* support board types */ - -#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_8xx\0" \ - "bootfile=/tftpboot/HMI10/uImage\0" \ - "kernel_addr=40040000\0" \ - "ramdisk_addr=40100000\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOARD_EARLY_INIT_R 1 -#define CONFIG_MISC_INIT_R 1 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - -/* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -/* Software (bit-bang) I2C driver configuration */ -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ - -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_STATUS_LED 1 /* Status LED enabled */ - -#define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - -#ifdef CONFIG_SPLASH_SCREEN - #define CONFIG_CMD_BMP -#endif - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ - -#if 0 -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ -#endif -#ifdef CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFFF00000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ - -/* use CFI flash driver */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/*----------------------------------------------------------------------- - * Hardware Information Block - */ -#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ -#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */ -#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#ifndef CONFIG_CAN_DRIVER -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) -#else /* we must activate GPL5 in the SIUMCR for CAN */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) -#endif /* CONFIG_CAN_DRIVER */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - * - * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! - */ -#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0100000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4100000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8100000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC100000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) -#define PCMCIA_MEM_WIN_NO 5 -#define NSCU_OE_INV 1 /* PCMCIA_GCRX_CXOE is inverted */ - -/*----------------------------------------------------------------------- - * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) - *----------------------------------------------------------------------- - */ - -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ -#ifndef CONFIG_STATUS_LED /* Status and IDE LED's are mutually exclusive */ -#define CONFIG_IDE_LED 1 /* LED for ide supported */ -#endif - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* - * FLASH timing: - */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \ - OR_SCY_3_CLK | OR_EHTR | OR_BI) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) - -#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM -#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V ) - -/* - * BR2/3 and OR2/3 (SDRAM) - * - */ -#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ -#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */ -#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ - -/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ -#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 - -#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM ) -#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) - -#ifndef CONFIG_CAN_DRIVER -#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM -#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) -#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */ -#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */ -#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ -#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI) -#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \ - BR_PS_8 | BR_MS_UPMB | BR_V ) -#endif /* CONFIG_CAN_DRIVER */ - -/* - * Memory Periodic Timer Prescaler - * - * The Divider for PTA (refresh timer) configuration is based on an - * example SDRAM configuration (64 MBit, one bank). The adjustment to - * the number of chip selects (NCS) and the actually needed refresh - * rate is done by setting MPTPR. - * - * PTA is calculated from - * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) - * - * gclk CPU clock (not bus clock!) - * Trefresh Refresh cycle * 4 (four word bursts used) - * - * 4096 Rows from SDRAM example configuration - * 1000 factor s -> ms - * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration - * 4 Number of refresh cycles per period - * 64 Refresh cycle in ms per number of rows - * -------------------------------------------- - * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 - * - * 50 MHz => 50.000.000 / Divider = 98 - * 66 Mhz => 66.000.000 / Divider = 129 - * 80 Mhz => 80.000.000 / Divider = 156 - */ - -#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64)) -#define CONFIG_SYS_MAMR_PTA 98 - -/* - * For 16 MBit, refresh rates could be 31.3 us - * (= 64 ms / 2K = 125 / quad bursts). - * For a simpler initialization, 15.6 us is used instead. - * - * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks - * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank - */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_HWCONFIG 1 - -#endif /* __CONFIG_H */ diff --git a/include/status_led.h b/include/status_led.h index f213595..b39ca64 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -43,7 +43,7 @@ void status_led_tick (unsigned long timestamp); void status_led_set (int led, int state); /***** TQM8xxL ********************************************************/ -#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_HMI10) +#if defined(CONFIG_TQM8xxL) # define STATUS_LED_PAR im_cpm.cp_pbpar # define STATUS_LED_DIR im_cpm.cp_pbdir # define STATUS_LED_ODR im_cpm.cp_pbodr @@ -318,21 +318,6 @@ void status_led_set (int led, int state); # define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ -/***** HMI10 **********************************************************/ -#elif defined(CONFIG_HMI10) -# define STATUS_LED_PAR im_ioport.iop_papar -# define STATUS_LED_DIR im_ioport.iop_padir -# define STATUS_LED_ODR im_ioport.iop_paodr -# define STATUS_LED_DAT im_ioport.iop_padat - -# define STATUS_LED_BIT 0x00000001 /* LED is on PA15 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - /***** NetPhone ********************************************************/ #elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2) /* XXX empty just to avoid the error */ |