diff options
33 files changed, 1615 insertions, 175 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index f47fca5..986e0dc 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -549,6 +549,7 @@ Rowel Atienza <rowel@diwalabs.com> Stefano Babic <sbabic@denx.de> + ea20 davinci polaris xscale trizepsiv xscale mx51evk i.MX51 @@ -853,6 +854,11 @@ Alex Züpke <azu@sysgo.de> lart SA1100 dnp1110 SA1110 +Syed Mohammed Khasim <sm.khasim@gmail.com> +Sughosh Ganu <urwithsughosh@gmail.com> + + hawkboard ARM926EJS (OMAP-L138) + ------------------------------------------------------------------------- Unknown / orphaned boards: diff --git a/board/davinci/common/misc.h b/arch/arm/include/asm/arch-davinci/davinci_misc.h index a6ac3b9..347aa89 100644 --- a/board/davinci/common/misc.h +++ b/arch/arm/include/asm/arch-davinci/davinci_misc.h @@ -45,10 +45,25 @@ struct pinmux_resource { .n_pins = ARRAY_SIZE(item) \ } +#define HAWKBOARD_KICK0_UNLOCK 0x83e70b13 +#define HAWKBOARD_KICK1_UNLOCK 0x95a4f1e0 + +struct lpsc_resource { + const int lpsc_no; +}; + int dvevm_read_mac_address(uint8_t *buf); void davinci_sync_env_enetaddr(uint8_t *rom_enetaddr); int davinci_configure_pin_mux(const struct pinmux_config *pins, int n_pins); int davinci_configure_pin_mux_items(const struct pinmux_resource *item, int n_items); +#if defined(CONFIG_DRIVER_TI_EMAC) && defined(CONFIG_MACH_DAVINCI_DA850_EVM) +void davinci_emac_mii_mode_sel(int mode_sel); +#endif +#if defined(CONFIG_SOC_DA8XX) +void irq_init(void); +int da8xx_configure_lpsc_items(const struct lpsc_resource *item, + const int n_items); +#endif #endif /* __MISC_H */ diff --git a/arch/arm/include/asm/arch-davinci/hardware.h b/arch/arm/include/asm/arch-davinci/hardware.h index 3520cf8..b95fa97 100644 --- a/arch/arm/include/asm/arch-davinci/hardware.h +++ b/arch/arm/include/asm/arch-davinci/hardware.h @@ -133,7 +133,8 @@ typedef volatile unsigned int * dv_reg_p; #define DAVINCI_PSC1_BASE 0x01e27000 #define DAVINCI_SPI0_BASE 0x01c41000 #define DAVINCI_USB_OTG_BASE 0x01e00000 -#define DAVINCI_SPI1_BASE 0x01e12000 +#define DAVINCI_SPI1_BASE (cpu_is_da830() ? \ + 0x01e12000 : 0x01f0e000) #define DAVINCI_GPIO_BASE 0x01e26000 #define DAVINCI_EMAC_CNTRL_REGS_BASE 0x01e23000 #define DAVINCI_EMAC_WRAPPER_CNTRL_REGS_BASE 0x01e22000 @@ -149,7 +150,12 @@ typedef volatile unsigned int * dv_reg_p; #define DAVINCI_DDR_EMIF_DATA_BASE 0xc0000000 #define DAVINCI_INTC_BASE 0xfffee000 #define DAVINCI_BOOTCFG_BASE 0x01c14000 +#define JTAG_ID_REG (DAVINCI_BOOTCFG_BASE + 0x18) +#define GPIO_BANK2_REG_DIR_ADDR (DAVINCI_GPIO_BASE + 0x38) +#define GPIO_BANK2_REG_OPDATA_ADDR (DAVINCI_GPIO_BASE + 0x3c) +#define GPIO_BANK2_REG_SET_ADDR (DAVINCI_GPIO_BASE + 0x40) +#define GPIO_BANK2_REG_CLR_ADDR (DAVINCI_GPIO_BASE + 0x44) #endif /* CONFIG_SOC_DA8XX */ /* Power and Sleep Controller (PSC) Domains */ @@ -363,6 +369,9 @@ struct davinci_pllc_regs { #define davinci_pllc_regs ((struct davinci_pllc_regs *)DAVINCI_PLL_CNTRL0_BASE) #define DAVINCI_PLLC_DIV_MASK 0x1f +#define ASYNC3 get_async3_src() +#define PLL1_SYSCLK2 ((1 << 16) | 0x2) +#define DAVINCI_SPI1_CLKID (cpu_is_da830() ? 2 : ASYNC3) /* Clock IDs */ enum davinci_clk_ids { DAVINCI_SPI0_CLKID = 2, @@ -379,7 +388,10 @@ int clk_get(enum davinci_clk_ids id); /* Boot config */ struct davinci_syscfg_regs { dv_reg revid; - dv_reg rsvd[71]; + dv_reg rsvd[13]; + dv_reg kick0; + dv_reg kick1; + dv_reg rsvd1[56]; dv_reg pinmux[20]; dv_reg suspsrc; dv_reg chipsig; @@ -442,6 +454,27 @@ struct davinci_uart_ctrl_regs { #define DAVINCI_UART_PWREMU_MGMT_URRST (1 << 13) #define DAVINCI_UART_PWREMU_MGMT_UTRST (1 << 14) +static inline int cpu_is_da830(void) +{ + unsigned int jtag_id = REG(JTAG_ID_REG); + unsigned short part_no = (jtag_id >> 12) & 0xffff; + + return ((part_no == 0xb7df) ? 1 : 0); +} +static inline int cpu_is_da850(void) +{ + unsigned int jtag_id = REG(JTAG_ID_REG); + unsigned short part_no = (jtag_id >> 12) & 0xffff; + + return ((part_no == 0xb7d1) ? 1 : 0); +} + +static inline int get_async3_src(void) +{ + return (REG(&davinci_syscfg_regs->cfgchip3) & 0x10) ? + PLL1_SYSCLK2 : 2; +} + #endif /* CONFIG_SOC_DA8XX */ #endif /* __ASM_ARCH_HARDWARE_H */ diff --git a/board/davinci/common/Makefile b/board/davinci/common/Makefile index 5ddb564..a1d3de2 100644 --- a/board/davinci/common/Makefile +++ b/board/davinci/common/Makefile @@ -29,7 +29,7 @@ endif LIB = $(obj)lib$(VENDOR).o -COBJS := misc.o +COBJS := misc.o davinci_pinmux.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/davinci/common/davinci_pinmux.c b/board/davinci/common/davinci_pinmux.c new file mode 100644 index 0000000..ce58f71 --- /dev/null +++ b/board/davinci/common/davinci_pinmux.c @@ -0,0 +1,105 @@ +/* + * DaVinci pinmux functions. + * + * Copyright (C) 2009 Nick Thompson, GE Fanuc Ltd, <nick.thompson@gefanuc.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * Copyright (C) 2008 Lyrtech <www.lyrtech.com> + * Copyright (C) 2004 Texas Instruments. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <asm/arch/hardware.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> + +/* + * Change the setting of a pin multiplexer field. + * + * Takes an array of pinmux settings similar to: + * + * struct pinmux_config uart_pins[] = { + * { &davinci_syscfg_regs->pinmux[8], 2, 7 }, + * { &davinci_syscfg_regs->pinmux[9], 2, 0 } + * }; + * + * Stepping through the array, each pinmux[n] register has the given value + * set in the pin mux field specified. + * + * The number of pins in the array must be passed (ARRAY_SIZE can provide + * this value conveniently). + * + * Returns 0 if all field numbers and values are in the correct range, + * else returns -1. + */ +int davinci_configure_pin_mux(const struct pinmux_config *pins, + const int n_pins) +{ + int i; + + /* check for invalid pinmux values */ + for (i = 0; i < n_pins; i++) { + if (pins[i].field >= PIN_MUX_NUM_FIELDS || + (pins[i].value & ~PIN_MUX_FIELD_MASK) != 0) + return -1; + } + + /* configure the pinmuxes */ + for (i = 0; i < n_pins; i++) { + const int offset = pins[i].field * PIN_MUX_FIELD_SIZE; + const unsigned int value = pins[i].value << offset; + const unsigned int mask = PIN_MUX_FIELD_MASK << offset; + const dv_reg *mux = pins[i].mux; + + writel(value | (readl(mux) & (~mask)), mux); + } + + return 0; +} + +/* + * Configure multiple pinmux resources. + * + * Takes an pinmux_resource array of pinmux_config and pin counts: + * + * const struct pinmux_resource pinmuxes[] = { + * PINMUX_ITEM(uart_pins), + * PINMUX_ITEM(i2c_pins), + * }; + * + * The number of items in the array must be passed (ARRAY_SIZE can provide + * this value conveniently). + * + * Each item entry is configured in the defined order. If configuration + * of any item fails, -1 is returned and none of the following items are + * configured. On success, 0 is returned. + */ +int davinci_configure_pin_mux_items(const struct pinmux_resource *item, + const int n_items) +{ + int i; + + for (i = 0; i < n_items; i++) { + if (davinci_configure_pin_mux(item[i].pins, + item[i].n_pins) != 0) + return -1; + } + + return 0; +} diff --git a/board/davinci/common/misc.c b/board/davinci/common/misc.c index fa9dd9f..08c898f 100644 --- a/board/davinci/common/misc.c +++ b/board/davinci/common/misc.c @@ -29,10 +29,11 @@ #include <net.h> #include <asm/arch/hardware.h> #include <asm/io.h> -#include "misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; +#ifndef CONFIG_PRELOADER int dram_init(void) { /* dram_init must store complete ramsize in gd->ram_size */ @@ -47,6 +48,7 @@ void dram_init_banksize(void) gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; gd->bd->bi_dram[0].size = gd->ram_size; } +#endif #ifdef CONFIG_DRIVER_TI_EMAC @@ -76,6 +78,22 @@ err: } /* + * Set the mii mode as MII or RMII + */ +#if defined(CONFIG_DRIVER_TI_EMAC) +void davinci_emac_mii_mode_sel(int mode_sel) +{ + int val; + + val = readl(&davinci_syscfg_regs->cfgchip3); + if (mode_sel == 0) + val &= ~(1 << 8); + else + val |= (1 << 8); + writel(val, &davinci_syscfg_regs->cfgchip3); +} +#endif +/* * If there is no MAC address in the environment, then it will be initialized * (silently) from the value in the EEPROM. */ @@ -94,79 +112,38 @@ void davinci_sync_env_enetaddr(uint8_t *rom_enetaddr) } } -#endif /* DAVINCI_EMAC */ +#endif /* CONFIG_DRIVER_TI_EMAC */ -/* - * Change the setting of a pin multiplexer field. - * - * Takes an array of pinmux settings similar to: - * - * struct pinmux_config uart_pins[] = { - * { &davinci_syscfg_regs->pinmux[8], 2, 7 }, - * { &davinci_syscfg_regs->pinmux[9], 2, 0 } - * }; - * - * Stepping through the array, each pinmux[n] register has the given value - * set in the pin mux field specified. - * - * The number of pins in the array must be passed (ARRAY_SIZE can provide - * this value conveniently). - * - * Returns 0 if all field numbers and values are in the correct range, - * else returns -1. - */ -int davinci_configure_pin_mux(const struct pinmux_config *pins, - const int n_pins) +#if defined(CONFIG_SOC_DA8XX) +#ifndef CONFIG_USE_IRQ +void irq_init(void) { - int i; + /* + * Mask all IRQs by clearing the global enable and setting + * the enable clear for all the 90 interrupts. + */ - /* check for invalid pinmux values */ - for (i = 0; i < n_pins; i++) { - if (pins[i].field >= PIN_MUX_NUM_FIELDS || - (pins[i].value & ~PIN_MUX_FIELD_MASK) != 0) - return -1; - } + writel(0, &davinci_aintc_regs->ger); - /* configure the pinmuxes */ - for (i = 0; i < n_pins; i++) { - const int offset = pins[i].field * PIN_MUX_FIELD_SIZE; - const unsigned int value = pins[i].value << offset; - const unsigned int mask = PIN_MUX_FIELD_MASK << offset; - const dv_reg *mux = pins[i].mux; + writel(0, &davinci_aintc_regs->hier); - writel(value | (readl(mux) & (~mask)), mux); - } - - return 0; + writel(0xffffffff, &davinci_aintc_regs->ecr1); + writel(0xffffffff, &davinci_aintc_regs->ecr2); + writel(0xffffffff, &davinci_aintc_regs->ecr3); } +#endif /* - * Configure multiple pinmux resources. - * - * Takes an pinmux_resource array of pinmux_config and pin counts: - * - * const struct pinmux_resource pinmuxes[] = { - * PINMUX_ITEM(uart_pins), - * PINMUX_ITEM(i2c_pins), - * }; - * - * The number of items in the array must be passed (ARRAY_SIZE can provide - * this value conveniently). - * - * Each item entry is configured in the defined order. If configuration - * of any item fails, -1 is returned and none of the following items are - * configured. On success, 0 is returned. + * Enable PSC for various peripherals. */ -int davinci_configure_pin_mux_items(const struct pinmux_resource *item, +int da8xx_configure_lpsc_items(const struct lpsc_resource *item, const int n_items) { int i; - for (i = 0; i < n_items; i++) { - if (davinci_configure_pin_mux(item[i].pins, - item[i].n_pins) != 0) - return -1; - } + for (i = 0; i < n_items; i++) + lpsc_on(item[i].lpsc_no); return 0; } +#endif diff --git a/board/davinci/da8xxevm/Makefile b/board/davinci/da8xxevm/Makefile index 88fee50..c1b2119 100644 --- a/board/davinci/da8xxevm/Makefile +++ b/board/davinci/da8xxevm/Makefile @@ -27,9 +27,9 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS-y += common.o COBJS-$(CONFIG_MACH_DAVINCI_DA830_EVM) += da830evm.o COBJS-$(CONFIG_MACH_DAVINCI_DA850_EVM) += da850evm.o +COBJS-$(CONFIG_MACH_DAVINCI_HAWK) += hawkboard.o COBJS := $(COBJS-y) diff --git a/board/davinci/da8xxevm/common.c b/board/davinci/da8xxevm/common.c deleted file mode 100644 index 9cd5204c..0000000 --- a/board/davinci/da8xxevm/common.c +++ /dev/null @@ -1,55 +0,0 @@ -/* - * Miscellaneous DA8XX functions. - * - * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#include <asm/io.h> -#include <asm/arch/hardware.h> -#include "common.h" - -#ifndef CONFIG_USE_IRQ -void irq_init(void) -{ - /* - * Mask all IRQs by clearing the global enable and setting - * the enable clear for all the 90 interrupts. - */ - - writel(0, &davinci_aintc_regs->ger); - - writel(0, &davinci_aintc_regs->hier); - - writel(0xffffffff, &davinci_aintc_regs->ecr1); - writel(0xffffffff, &davinci_aintc_regs->ecr2); - writel(0xffffffff, &davinci_aintc_regs->ecr3); -} -#endif - -/* - * Enable PSC for various peripherals. - */ -int da8xx_configure_lpsc_items(const struct lpsc_resource *item, - const int n_items) -{ - int i; - - for (i = 0; i < n_items; i++) - lpsc_on(item[i].lpsc_no); - - return 0; -} diff --git a/board/davinci/da8xxevm/common.h b/board/davinci/da8xxevm/common.h deleted file mode 100644 index 7ae63a6..0000000 --- a/board/davinci/da8xxevm/common.h +++ /dev/null @@ -1,30 +0,0 @@ -/* - * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#ifndef __COMMON_H -#define __COMMON_H - -struct lpsc_resource { - const int lpsc_no; -}; - -void irq_init(void); -int da8xx_configure_lpsc_items(const struct lpsc_resource *item, - int n_items); - -#endif /* __COMMON_H */ diff --git a/board/davinci/da8xxevm/da830evm.c b/board/davinci/da8xxevm/da830evm.c index 8a9f988..0650653 100644 --- a/board/davinci/da8xxevm/da830evm.c +++ b/board/davinci/da8xxevm/da830evm.c @@ -40,8 +40,7 @@ #include <asm/arch/emif_defs.h> #include <asm/arch/emac_defs.h> #include <asm/io.h> -#include "../common/misc.h" -#include "common.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/da8xxevm/da850evm.c b/board/davinci/da8xxevm/da850evm.c index c3267cb..b088c9c 100644 --- a/board/davinci/da8xxevm/da850evm.c +++ b/board/davinci/da8xxevm/da850evm.c @@ -29,8 +29,7 @@ #include <asm/arch/emif_defs.h> #include <asm/arch/emac_defs.h> #include <asm/io.h> -#include "../common/misc.h" -#include "common.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; @@ -54,6 +53,15 @@ static const struct pinmux_config uart_pins[] = { #ifdef CONFIG_DRIVER_TI_EMAC static const struct pinmux_config emac_pins[] = { +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII + { pinmux(14), 8, 2 }, + { pinmux(14), 8, 3 }, + { pinmux(14), 8, 4 }, + { pinmux(14), 8, 5 }, + { pinmux(14), 8, 6 }, + { pinmux(14), 8, 7 }, + { pinmux(15), 8, 1 }, +#else /* ! CONFIG_DRIVER_TI_EMAC_USE_RMII */ { pinmux(2), 8, 1 }, { pinmux(2), 8, 2 }, { pinmux(2), 8, 3 }, @@ -69,10 +77,10 @@ static const struct pinmux_config emac_pins[] = { { pinmux(3), 8, 5 }, { pinmux(3), 8, 6 }, { pinmux(3), 8, 7 }, +#endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */ { pinmux(4), 8, 0 }, { pinmux(4), 8, 1 } }; -#endif /* CONFIG_DRIVER_TI_EMAC */ /* I2C pin muxer settings */ static const struct pinmux_config i2c_pins[] = { @@ -99,6 +107,13 @@ const struct pinmux_config nand_pins[] = { }; #endif +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII +#define HAS_RMII 1 +#else +#define HAS_RMII 0 +#endif +#endif /* CONFIG_DRIVER_TI_EMAC */ + static const struct pinmux_resource pinmuxes[] = { #ifdef CONFIG_SPI_FLASH PINMUX_ITEM(spi1_pins), @@ -203,9 +218,8 @@ int board_init(void) #ifdef CONFIG_DRIVER_TI_EMAC if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0) return 1; - /* set cfgchip3 to select MII */ - writel(readl(&davinci_syscfg_regs->cfgchip3) & ~(1 << 8), - &davinci_syscfg_regs->cfgchip3); + + davinci_emac_mii_mode_sel(HAS_RMII); #endif /* CONFIG_DRIVER_TI_EMAC */ /* enable the console UART */ @@ -218,11 +232,100 @@ int board_init(void) #ifdef CONFIG_DRIVER_TI_EMAC +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII +/** + * rmii_hw_init + * + * DA850/OMAP-L138 EVM can interface to a daughter card for + * additional features. This card has an I2C GPIO Expander TCA6416 + * to select the required functions like camera, RMII Ethernet, + * character LCD, video. + * + * Initialization of the expander involves configuring the + * polarity and direction of the ports. P07-P05 are used here. + * These ports are connected to a Mux chip which enables only one + * functionality at a time. + * + * For RMII phy to respond, the MII MDIO clock has to be disabled + * since both the PHY devices have address as zero. The MII MDIO + * clock is controlled via GPIO2[6]. + * + * This code is valid for Beta version of the hardware + */ +int rmii_hw_init(void) +{ + const struct pinmux_config gpio_pins[] = { + { pinmux(6), 8, 1 } + }; + u_int8_t buf[2]; + unsigned int temp; + int ret; + + /* PinMux for GPIO */ + if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0) + return 1; + + /* I2C Exapnder configuration */ + /* Set polarity to non-inverted */ + buf[0] = 0x0; + buf[1] = 0x0; + ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 4, 1, buf, 2); + if (ret) { + printf("\nExpander @ 0x%02x write FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + return ret; + } + + /* Configure P07-P05 as outputs */ + buf[0] = 0x1f; + buf[1] = 0xff; + ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 6, 1, buf, 2); + if (ret) { + printf("\nExpander @ 0x%02x write FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + } + + /* For Ethernet RMII selection + * P07(SelA)=0 + * P06(SelB)=1 + * P05(SelC)=1 + */ + if (i2c_read(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) { + printf("\nExpander @ 0x%02x read FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + } + + buf[0] &= 0x1f; + buf[0] |= (0 << 7) | (1 << 6) | (1 << 5); + if (i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) { + printf("\nExpander @ 0x%02x write FAILED!!!\n", + CONFIG_SYS_I2C_EXPANDER_ADDR); + } + + /* Set the output as high */ + temp = REG(GPIO_BANK2_REG_SET_ADDR); + temp |= (0x01 << 6); + REG(GPIO_BANK2_REG_SET_ADDR) = temp; + + /* Set the GPIO direction as output */ + temp = REG(GPIO_BANK2_REG_DIR_ADDR); + temp &= ~(0x01 << 6); + REG(GPIO_BANK2_REG_DIR_ADDR) = temp; + + return 0; +} +#endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */ + /* * Initializes on-board ethernet controllers. */ int board_eth_init(bd_t *bis) { +#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII + /* Select RMII fucntion through the expander */ + if (rmii_hw_init()) + printf("RMII hardware init failed!!!\n"); +#endif if (!davinci_emac_initialize()) { printf("Error: Ethernet init failed!\n"); return -1; diff --git a/board/davinci/da8xxevm/hawkboard.c b/board/davinci/da8xxevm/hawkboard.c new file mode 100644 index 0000000..f34830e --- /dev/null +++ b/board/davinci/da8xxevm/hawkboard.c @@ -0,0 +1,68 @@ +/* + * Modified for Hawkboard - Syed Mohammed Khasim <khasim@beagleboard.org> + * + * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar@ti.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * Copyright (C) 2004 Texas Instruments. + * + * ---------------------------------------------------------------------------- + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + */ + +#include <common.h> +#include <asm/errno.h> +#include <asm/arch/hardware.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> +#include <ns16550.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_init(void) +{ + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_OMAPL138_HAWKBOARD; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + return 0; +} + +int board_early_init_f(void) +{ + /* + * Kick Registers need to be set to allow access to Pin Mux registers + */ + writel(HAWKBOARD_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); + writel(HAWKBOARD_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); + + /* set cfgchip3 to select mii */ + writel(readl(&davinci_syscfg_regs->cfgchip3) & + ~(1 << 8), &davinci_syscfg_regs->cfgchip3); + + return 0; +} + +int misc_init_r(void) +{ + char buf[32]; + + printf("ARM Clock : %s MHz\n", + strmhz(buf, clk_get(DAVINCI_ARM_CLKID))); + + return 0; +} diff --git a/board/davinci/da8xxevm/hawkboard_nand_spl.c b/board/davinci/da8xxevm/hawkboard_nand_spl.c new file mode 100644 index 0000000..9155236 --- /dev/null +++ b/board/davinci/da8xxevm/hawkboard_nand_spl.c @@ -0,0 +1,157 @@ +/* + * Modified for Hawkboard - Syed Mohammed Khasim <khasim@beagleboard.org> + * + * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar@ti.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * Copyright (C) 2004 Texas Instruments. + * + * ---------------------------------------------------------------------------- + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + */ + +#include <common.h> +#include <asm/errno.h> +#include <asm/arch/hardware.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> +#include <ns16550.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define pinmux(x) (&davinci_syscfg_regs->pinmux[x]) + +static const struct pinmux_config mii_pins[] = { + { pinmux(2), 8, 1 }, + { pinmux(2), 8, 2 }, + { pinmux(2), 8, 3 }, + { pinmux(2), 8, 4 }, + { pinmux(2), 8, 5 }, + { pinmux(2), 8, 6 }, + { pinmux(2), 8, 7 } +}; + +static const struct pinmux_config mdio_pins[] = { + { pinmux(4), 8, 0 }, + { pinmux(4), 8, 1 } +}; + +static const struct pinmux_config nand_pins[] = { + { pinmux(7), 1, 1 }, + { pinmux(7), 1, 2 }, + { pinmux(7), 1, 4 }, + { pinmux(7), 1, 5 }, + { pinmux(9), 1, 0 }, + { pinmux(9), 1, 1 }, + { pinmux(9), 1, 2 }, + { pinmux(9), 1, 3 }, + { pinmux(9), 1, 4 }, + { pinmux(9), 1, 5 }, + { pinmux(9), 1, 6 }, + { pinmux(9), 1, 7 }, + { pinmux(12), 1, 5 }, + { pinmux(12), 1, 6 } +}; + +static const struct pinmux_config uart2_pins[] = { + { pinmux(0), 4, 6 }, + { pinmux(0), 4, 7 }, + { pinmux(4), 2, 4 }, + { pinmux(4), 2, 5 } +}; + +static const struct pinmux_config i2c_pins[] = { + { pinmux(4), 2, 4 }, + { pinmux(4), 2, 5 } +}; + +static const struct pinmux_resource pinmuxes[] = { + PINMUX_ITEM(mii_pins), + PINMUX_ITEM(mdio_pins), + PINMUX_ITEM(i2c_pins), + PINMUX_ITEM(nand_pins), + PINMUX_ITEM(uart2_pins), +}; + +static const struct lpsc_resource lpsc[] = { + { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ + { DAVINCI_LPSC_SPI1 }, /* Serial Flash */ + { DAVINCI_LPSC_EMAC }, /* image download */ + { DAVINCI_LPSC_UART2 }, /* console */ + { DAVINCI_LPSC_GPIO }, +}; + +void board_init_f(ulong bootflag) +{ + /* + * Kick Registers need to be set to allow access to Pin Mux registers + */ + writel(HAWKBOARD_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); + writel(HAWKBOARD_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); + + /* setup the SUSPSRC for ARM to control emulation suspend */ + writel(readl(&davinci_syscfg_regs->suspsrc) & + ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | + DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 | + DAVINCI_SYSCFG_SUSPSRC_UART2), &davinci_syscfg_regs->suspsrc); + + /* Power on required peripherals + * ARM does not have acess by default to PSC0 and PSC1 + * assuming here that the DSP bootloader has set the IOPU + * such that PSC access is available to ARM + */ + da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)); + + /* configure pinmux settings */ + davinci_configure_pin_mux_items(pinmuxes, + ARRAY_SIZE(pinmuxes)); + + writel(readl(&davinci_uart2_ctrl_regs->pwremu_mgmt) | + (DAVINCI_UART_PWREMU_MGMT_FREE) | + (DAVINCI_UART_PWREMU_MGMT_URRST) | + (DAVINCI_UART_PWREMU_MGMT_UTRST), + &davinci_uart2_ctrl_regs->pwremu_mgmt); + + NS16550_init((NS16550_t)(DAVINCI_UART2_BASE), + CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); + + puts("Nand boot...\n"); + + nand_boot(); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} + +void putc(char c) +{ + if (gd->flags & GD_FLG_SILENT) + return; + + if (c == '\n') + NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), '\r'); + + NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), c); +} + +void hang(void) +{ + puts("### ERROR ### Please RESET the board ###\n"); + for (;;) + ; +} diff --git a/board/davinci/dm355evm/dm355evm.c b/board/davinci/dm355evm/dm355evm.c index 87f284c..b9260b8 100644 --- a/board/davinci/dm355evm/dm355evm.c +++ b/board/davinci/dm355evm/dm355evm.c @@ -22,7 +22,7 @@ #include <asm/arch/hardware.h> #include <asm/arch/emif_defs.h> #include <asm/arch/nand_defs.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> #include <net.h> #include <netdev.h> diff --git a/board/davinci/dm355leopard/dm355leopard.c b/board/davinci/dm355leopard/dm355leopard.c index e89786e..0ee0d11 100644 --- a/board/davinci/dm355leopard/dm355leopard.c +++ b/board/davinci/dm355leopard/dm355leopard.c @@ -22,7 +22,7 @@ #include <asm/arch/hardware.h> #include <asm/arch/gpio_defs.h> #include <asm/arch/nand_defs.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> #include <net.h> #include <netdev.h> diff --git a/board/davinci/dm365evm/dm365evm.c b/board/davinci/dm365evm/dm365evm.c index 85dbe2a..bc681f7 100644 --- a/board/davinci/dm365evm/dm365evm.c +++ b/board/davinci/dm365evm/dm365evm.c @@ -24,7 +24,7 @@ #include <asm/arch/nand_defs.h> #include <asm/arch/gpio_defs.h> #include <netdev.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/dvevm/dvevm.c b/board/davinci/dvevm/dvevm.c index 073c21a..d5c851b 100644 --- a/board/davinci/dvevm/dvevm.c +++ b/board/davinci/dvevm/dvevm.c @@ -27,7 +27,7 @@ #include <common.h> #include <i2c.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/ea20/Makefile b/board/davinci/ea20/Makefile new file mode 100644 index 0000000..ddd2564 --- /dev/null +++ b/board/davinci/ea20/Makefile @@ -0,0 +1,53 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += ea20.o + +COBJS := $(COBJS-y) + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak *~ .depend + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/davinci/ea20/ea20.c b/board/davinci/ea20/ea20.c new file mode 100644 index 0000000..9d0f71b --- /dev/null +++ b/board/davinci/ea20/ea20.c @@ -0,0 +1,196 @@ +/* + * (C) Copyright 2010 + * Stefano Babic, DENX Software Engineering, sbabic@denx.de + * + * Based on da850evm.c, original Copyrights follow: + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on da830evm.c. Original Copyrights follow: + * + * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <i2c.h> +#include <net.h> +#include <netdev.h> +#include <asm/arch/hardware.h> +#include <asm/arch/emif_defs.h> +#include <asm/arch/emac_defs.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define pinmux(x) (&davinci_syscfg_regs->pinmux[x]) + +/* SPI0 pin muxer settings */ +static const struct pinmux_config spi1_pins[] = { + { pinmux(5), 1, 1 }, + { pinmux(5), 1, 2 }, + { pinmux(5), 1, 4 }, + { pinmux(5), 1, 5 } +}; + +/* UART pin muxer settings */ +static const struct pinmux_config uart_pins[] = { + { pinmux(0), 4, 6 }, + { pinmux(0), 4, 7 }, + { pinmux(4), 2, 4 }, + { pinmux(4), 2, 5 } +}; + +#ifdef CONFIG_DRIVER_TI_EMAC +#define HAS_RMII 1 +static const struct pinmux_config emac_pins[] = { + { pinmux(14), 8, 2 }, + { pinmux(14), 8, 3 }, + { pinmux(14), 8, 4 }, + { pinmux(14), 8, 5 }, + { pinmux(14), 8, 6 }, + { pinmux(14), 8, 7 }, + { pinmux(15), 8, 1 }, + { pinmux(4), 8, 0 }, + { pinmux(4), 8, 1 } +}; +#endif + +#ifdef CONFIG_NAND_DAVINCI +const struct pinmux_config nand_pins[] = { + { pinmux(7), 1, 1 }, + { pinmux(7), 1, 2 }, + { pinmux(7), 1, 4 }, + { pinmux(7), 1, 5 }, + { pinmux(9), 1, 0 }, + { pinmux(9), 1, 1 }, + { pinmux(9), 1, 2 }, + { pinmux(9), 1, 3 }, + { pinmux(9), 1, 4 }, + { pinmux(9), 1, 5 }, + { pinmux(9), 1, 6 }, + { pinmux(9), 1, 7 }, + { pinmux(12), 1, 5 }, + { pinmux(12), 1, 6 } +}; +#endif + +static const struct pinmux_resource pinmuxes[] = { +#ifdef CONFIG_SPI_FLASH + PINMUX_ITEM(spi1_pins), +#endif + PINMUX_ITEM(uart_pins), +#ifdef CONFIG_NAND_DAVINCI + PINMUX_ITEM(nand_pins), +#endif +}; + +static const struct lpsc_resource lpsc[] = { + { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ + { DAVINCI_LPSC_SPI1 }, /* Serial Flash */ + { DAVINCI_LPSC_EMAC }, /* image download */ + { DAVINCI_LPSC_UART2 }, /* console */ + { DAVINCI_LPSC_GPIO }, +}; + +int board_init(void) +{ +#ifndef CONFIG_USE_IRQ + irq_init(); +#endif + + +#ifdef CONFIG_NAND_DAVINCI + /* + * NAND CS setup - cycle counts based on da850evm NAND timings in the + * Linux kernel @ 25MHz EMIFA + */ + writel((DAVINCI_ABCR_WSETUP(0) | + DAVINCI_ABCR_WSTROBE(0) | + DAVINCI_ABCR_WHOLD(0) | + DAVINCI_ABCR_RSETUP(0) | + DAVINCI_ABCR_RSTROBE(1) | + DAVINCI_ABCR_RHOLD(0) | + DAVINCI_ABCR_TA(0) | + DAVINCI_ABCR_ASIZE_8BIT), + &davinci_emif_regs->ab2cr); /* CS3 */ +#endif + + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_EA20; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* + * Power on required peripherals + * ARM does not have access by default to PSC0 and PSC1 + * assuming here that the DSP bootloader has set the IOPU + * such that PSC access is available to ARM + */ + if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc))) + return 1; + + /* setup the SUSPSRC for ARM to control emulation suspend */ + writel(readl(&davinci_syscfg_regs->suspsrc) & + ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | + DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 | + DAVINCI_SYSCFG_SUSPSRC_UART2), + &davinci_syscfg_regs->suspsrc); + + /* configure pinmux settings */ + if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes))) + return 1; + +#ifdef CONFIG_DRIVER_TI_EMAC + if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0) + return 1; + + davinci_emac_mii_mode_sel(HAS_RMII); +#endif /* CONFIG_DRIVER_TI_EMAC */ + + /* enable the console UART */ + writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | + DAVINCI_UART_PWREMU_MGMT_UTRST), + &davinci_uart2_ctrl_regs->pwremu_mgmt); + + return 0; +} + +#ifdef CONFIG_DRIVER_TI_EMAC + +/* + * Initializes on-board ethernet controllers. + */ +int board_eth_init(bd_t *bis) +{ + if (!davinci_emac_initialize()) { + printf("Error: Ethernet init failed!\n"); + return -1; + } + + /* + * This board has a RMII PHY. However, the MDC line on the SOM + * must not be disabled (there is no MII PHY on the + * baseboard) via the GPIO2[6], because this pin + * disables at the same time the SPI flash. + */ + + return 0; +} +#endif /* CONFIG_DRIVER_TI_EMAC */ diff --git a/board/davinci/schmoogie/schmoogie.c b/board/davinci/schmoogie/schmoogie.c index 80a0f9f..8b615a9 100644 --- a/board/davinci/schmoogie/schmoogie.c +++ b/board/davinci/schmoogie/schmoogie.c @@ -27,7 +27,7 @@ #include <common.h> #include <i2c.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c index 657cf2b..cc3ff7d 100644 --- a/board/davinci/sffsdr/sffsdr.c +++ b/board/davinci/sffsdr/sffsdr.c @@ -30,7 +30,7 @@ #include <common.h> #include <i2c.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> #define DAVINCI_A3CR (0x01E00014) /* EMIF-A CS3 config register. */ #define DAVINCI_A3CR_VAL (0x3FFFFFFD) /* EMIF-A CS3 value for FPGA. */ diff --git a/board/davinci/sonata/sonata.c b/board/davinci/sonata/sonata.c index 1dc42c4..c194290 100644 --- a/board/davinci/sonata/sonata.c +++ b/board/davinci/sonata/sonata.c @@ -28,7 +28,7 @@ #include <nand.h> #include <asm/arch/nand_defs.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/samsung/smdk6400/smdk6400_nand_spl.c b/board/samsung/smdk6400/smdk6400_nand_spl.c new file mode 100644 index 0000000..a023284 --- /dev/null +++ b/board/samsung/smdk6400/smdk6400_nand_spl.c @@ -0,0 +1,37 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> + * + * (C) Copyright 2008 + * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +void board_init_f(unsigned long bootflag) +{ + relocate_code(CONFIG_SYS_TEXT_BASE - TOTAL_MALLOC_LEN, NULL, + CONFIG_SYS_TEXT_BASE); +} @@ -76,6 +76,10 @@ pm9261 arm arm926ejs - ronetix pm9263 arm arm926ejs - ronetix at91 da830evm arm arm926ejs da8xxevm davinci davinci da850evm arm arm926ejs da8xxevm davinci davinci +hawkboard arm arm926ejs da8xxevm davinci davinci +hawkboard_nand arm arm926ejs da8xxevm davinci davinci hawkboard:NAND_U_BOOT +hawkboard_uart arm arm926ejs da8xxevm davinci davinci hawkboard:UART_U_BOOT +ea20 arm arm926ejs ea20 davinci davinci davinci_dm355evm arm arm926ejs dm355evm davinci davinci davinci_dm355leopard arm arm926ejs dm355leopard davinci davinci davinci_dm365evm arm arm926ejs dm365evm davinci davinci diff --git a/doc/README.hawkboard b/doc/README.hawkboard new file mode 100644 index 0000000..b7afec4 --- /dev/null +++ b/doc/README.hawkboard @@ -0,0 +1,93 @@ +Summary +======= +The README is for the boot procedure used for TI's OMAP-L138 based +hawkboard. The hawkboard comes with a 128MiB Nand flash and a 128MiB +DDR SDRAM along with a host of other controllers. + +The hawkboard is booted in three stages. The initial bootloader which +executes upon reset is the Rom Boot Loader(RBL) which sits in the +internal ROM of the omap. The RBL initialises the memory and the nand +controller, and copies the image stored at a predefined location(block +1) of the nand flash. The image loaded by the RBL to the memory is the +AIS signed nand_spl image. This, in turns copies the u-boot binary +from the nand flash to the memory and jumps to the u-boot entry point. + +AIS is an image format defined by TI for the images that are to be +loaded to memory by the RBL. The image is divided into a series of +sections and the image's entry point is specified. Each section comes +with meta data like the target address the section is to be copied to +and the size of the section, which is used by the RBL to load the +image. At the end of the image the RBL jumps to the image entry +point. + +The secondary stage bootloader(nand_spl) which is loaded by the RBL +then loads the u-boot from a predefined location in the nand to the +memory and jumps to the u-boot entry point. + +The reason a secondary stage bootloader is used is because the ECC +layout expected by the RBL is not the same as that used by +u-boot/linux. This also implies that for flashing the nand_spl image, +we need to use the u-boot which uses the ECC layout expected by the +RBL[1]. Booting u-boot over UART(UART boot) is explained here[2]. + + +Compilation +=========== +Three images might be needed + +* nand_spl - This is the secondary bootloader which boots the u-boot + binary. + + hawkboard_nand_config + + The nand_spl ELF gets generated under nand_spl/u-boot-spl. This + needs to be processed with the AISGen tool for generating the AIS + signed image to be flashed. Steps for generating the AIS image are + explained here[3]. + +* u-boot binary - This is the image flashed to the nand and copied to + the memory by the nand_spl. + + hawkboard_config + +* u-boot for uart boot - This is same as the u-boot binary generated + above, with the sole difference of the CONFIG_SYS_TEXT_BASE being + 0xc1080000, as expected by the RBL. + + hawkboard_uart_config + + +Flashing the images to Nand +=========================== +The nand_spl AIS image needs to be flashed to the block 1 of the +Nand flash, as that is the location the RBL expects the image[4]. For +flashing the nand_spl, boot over the u-boot specified in [1], and +flash the image + +=> tftpboot 0xc0700000 <nand_spl_ais.bin> +=> nand erase 0x20000 0x20000 +=> nand write.e 0xc0700000 0x20000 <nand_spl_size> + +The u-boot binary is flashed at location 0xe0000(block 6) of the nand +flash. The nand_spl loader expects the u-boot at this location. For +flashing the u-boot binary + +=> tftpboot 0xc0700000 u-boot.bin +=> nand erase 0xe0000 0x40000 +=> nand write.e 0xc0700000 0xe0000 <u-boot-size> + + +Links +===== + +[1] + http://code.google.com/p/hawkboard/downloads/detail?name=u-boot_uart_ais_v1.bin + +[2] + http://elinux.org/Hawkboard#Booting_u-boot_over_UART + +[3] + http://elinux.org/Hawkboard#Signing_u-boot_for_UART_boot + +[4] + http://processors.wiki.ti.com/index.php/RBL_UBL_and_host_program#RBL_booting_from_NAND_and_ECC.2FBad_blocks diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c index e06896f..43a3d79 100644 --- a/drivers/net/davinci_emac.c +++ b/drivers/net/davinci_emac.c @@ -243,8 +243,35 @@ static int gen_get_link_speed(int phy_addr) { u_int16_t tmp; - if (davinci_eth_phy_read(phy_addr, MII_STATUS_REG, &tmp) && (tmp & 0x04)) + if (davinci_eth_phy_read(phy_addr, MII_STATUS_REG, &tmp) && + (tmp & 0x04)) { +#if defined(CONFIG_DRIVER_TI_EMAC_USE_RMII) && \ + defined(CONFIG_MACH_DAVINCI_DA850_EVM) + davinci_eth_phy_read(phy_addr, PHY_ANLPAR, &tmp); + + /* Speed doesn't matter, there is no setting for it in EMAC. */ + if (tmp & (PHY_ANLPAR_TXFD | PHY_ANLPAR_10FD)) { + /* set EMAC for Full Duplex */ + writel(EMAC_MACCONTROL_MIIEN_ENABLE | + EMAC_MACCONTROL_FULLDUPLEX_ENABLE, + &adap_emac->MACCONTROL); + } else { + /*set EMAC for Half Duplex */ + writel(EMAC_MACCONTROL_MIIEN_ENABLE, + &adap_emac->MACCONTROL); + } + + if (tmp & (PHY_ANLPAR_TXFD | PHY_ANLPAR_TX)) + writel(readl(&adap_emac->MACCONTROL) | + EMAC_MACCONTROL_RMIISPEED_100, + &adap_emac->MACCONTROL); + else + writel(readl(&adap_emac->MACCONTROL) & + ~EMAC_MACCONTROL_RMIISPEED_100, + &adap_emac->MACCONTROL); +#endif return(1); + } return(0); } @@ -326,6 +353,12 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) } #endif +#if defined(CONFIG_DRIVER_TI_EMAC_USE_RMII) && \ + defined(CONFIG_MACH_DAVINCI_DA850_EVM) + adap_ewrap->c0rxen = adap_ewrap->c1rxen = adap_ewrap->c2rxen = 0; + adap_ewrap->c0txen = adap_ewrap->c1txen = adap_ewrap->c2txen = 0; + adap_ewrap->c0miscen = adap_ewrap->c1miscen = adap_ewrap->c2miscen = 0; +#endif rx_desc = emac_rx_desc; writel(1, &adap_emac->TXCONTROL); @@ -480,6 +513,12 @@ static void davinci_eth_close(struct eth_device *dev) writel(0, &adap_ewrap->EWCTL); #endif +#if defined(CONFIG_DRIVER_TI_EMAC_USE_RMII) && \ + defined(CONFIG_MACH_DAVINCI_DA850_EVM) + adap_ewrap->c0rxen = adap_ewrap->c1rxen = adap_ewrap->c2rxen = 0; + adap_ewrap->c0txen = adap_ewrap->c1txen = adap_ewrap->c2txen = 0; + adap_ewrap->c0miscen = adap_ewrap->c1miscen = adap_ewrap->c2miscen = 0; +#endif debug_emac("- emac_close\n"); } diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index 4224258..bbb5a9b 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -27,6 +27,7 @@ * Board */ #define CONFIG_DRIVER_TI_EMAC +#define CONFIG_USE_SPIFLASH /* * SoC Configuration @@ -71,6 +72,15 @@ #define CONFIG_BAUDRATE 115200 /* Default baud rate */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED + /* * I2C Configuration */ @@ -78,6 +88,7 @@ #define CONFIG_DRIVER_DAVINCI_I2C #define CONFIG_SYS_I2C_SPEED 25000 #define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ +#define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20 /* * Flash & Environment @@ -115,6 +126,16 @@ #define CONFIG_NET_MULTI #endif +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE (64 << 10) +#define CONFIG_ENV_OFFSET (256 << 10) +#define CONFIG_ENV_SECT_SIZE (64 << 10) +#define CONFIG_SYS_NO_FLASH +#endif + /* * U-Boot general configuration */ @@ -179,6 +200,14 @@ #define CONFIG_CMD_UBIFS #endif +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SF +#define CONFIG_CMD_SAVEENV +#endif + #if !defined(CONFIG_USE_NAND) && \ !defined(CONFIG_USE_NOR) && \ !defined(CONFIG_USE_SPIFLASH) diff --git a/include/configs/ea20.h b/include/configs/ea20.h new file mode 100644 index 0000000..48ce945 --- /dev/null +++ b/include/configs/ea20.h @@ -0,0 +1,192 @@ +/* + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on davinci_dvevm.h. Original Copyrights follow: + * + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Board + */ +#define CONFIG_DRIVER_TI_EMAC +#define CONFIG_USE_SPIFLASH +#define CONFIG_DRIVER_TI_EMAC_USE_RMII + +/* + * SoC Configuration + */ +#define CONFIG_MACH_DAVINCI_DA850_EVM +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) +#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SYS_TEXT_BASE 0xc1080000 + +/* + * Memory Info + */ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ +#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */ +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ + +/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) + +/* memtest will be run on 16MB */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024) + +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024) /* regular stack */ + +/* + * Serial Driver info + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */ +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED + +/* + * Network & Ethernet Configuration + */ +#ifdef CONFIG_DRIVER_TI_EMAC +#define CONFIG_EMAC_MDIO_PHY_NUM 0 +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE (8 << 10) +#define CONFIG_ENV_OFFSET (256 << 10) +#define CONFIG_ENV_SECT_SIZE (64 << 10) +#define CONFIG_SYS_NO_FLASH +#endif + +/* + * U-Boot general configuration + */ +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CONFIG_SYS_PROMPT "ea20 > " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* + * Linux Information + */ +#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTDELAY 3 + +/* + * U-Boot commands + */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MEMORY + +#ifndef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_MII +#undef CONFIG_CMD_PING +#endif + +#ifdef CONFIG_USE_NAND +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_NAND + +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_LZO +#define CONFIG_RBTREE +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SF +#define CONFIG_CMD_SAVEENV +#endif + +#if !defined(CONFIG_USE_NAND) && \ + !defined(CONFIG_USE_NOR) && \ + !defined(CONFIG_USE_SPIFLASH) +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_SIZE (16 << 10) +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_ENV +#endif + +/* additions for new relocation code, must added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0xc0000000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ + GENERATED_GBL_DATA_SIZE) +#endif /* __CONFIG_H */ diff --git a/include/configs/hawkboard.h b/include/configs/hawkboard.h new file mode 100644 index 0000000..23a88d0 --- /dev/null +++ b/include/configs/hawkboard.h @@ -0,0 +1,206 @@ +/* + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on davinci_dvevm.h. Original Copyrights follow: + * + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Board + */ +#define CONFIG_SYS_USE_NAND 1 + +/* + * SoC Configuration + */ +#define CONFIG_MACH_DAVINCI_HAWK +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) +#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F + +#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_UART_U_BOOT) +#define CONFIG_SYS_TEXT_BASE 0xc1080000 +#else +#define CONFIG_SYS_TEXT_BASE 0xc1180000 +#endif + +/* + * Memory Info + */ +#define CONFIG_SYS_MALLOC_LEN (1*1024*1024) /* malloc() len */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE +#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */ +#define CONFIG_SYS_SDRAM_BASE 0xc0000000 +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 -\ + GENERATED_GBL_DATA_SIZE) + +/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1) + +/* memtest will be run on 16MB */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024) + +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024) /* regular stack */ + +/* + * Serial Driver info + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Network & Ethernet Configuration + */ +#define CONFIG_EMAC_MDIO_PHY_NUM 0x7 +#if !defined(CONFIG_NAND_SPL) +#define CONFIG_DRIVER_TI_EMAC +#endif +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI + +/* + * Nand Flash + */ +#ifdef CONFIG_SYS_USE_NAND +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_CLE_MASK 0x10 +#define CONFIG_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CFG_DAVINCI_STD_NAND_LAYOUT +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_PAGE_2K +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +/* Max number of NAND devices */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE_LIST { 0x62000000, } +#define NAND_MAX_CHIPS 1 +/* Block 0--not used by bootcode */ +#define CONFIG_ENV_OFFSET 0x0 + +#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0xe0000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x40000 +#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1180000 +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \ + CONFIG_SYS_NAND_U_BOOT_SIZE - \ + CONFIG_SYS_MALLOC_LEN - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_NAND_ECCPOS { \ + 24, 25, 26, 27, 28, \ + 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \ + 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \ + 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \ + 59, 60, 61, 62, 63 } +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 10 +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \ + CONFIG_SYS_NAND_ECCSIZE) +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \ + CONFIG_SYS_NAND_ECCSTEPS) +#endif /* CONFIG_SYS_USE_NAND */ + +/* + * U-Boot general configuration + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CONFIG_SYS_PROMPT "hawkboard > " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* + * Linux Information + */ +#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100) +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS \ + "mem=128M console=ttyS2,115200n8 root=/dev/ram0 rw initrd=0xc1180000,"\ + "4M ip=static" +#define CONFIG_BOOTDELAY 3 + +/* + * U-Boot commands + */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MEMORY + +#ifdef CONFIG_SYS_USE_NAND +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_NAND +#endif + +#ifndef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_MII +#undef CONFIG_CMD_PING +#endif + +#endif /* __CONFIG_H */ diff --git a/nand_spl/board/davinci/da8xxevm/Makefile b/nand_spl/board/davinci/da8xxevm/Makefile new file mode 100644 index 0000000..4cae223 --- /dev/null +++ b/nand_spl/board/davinci/da8xxevm/Makefile @@ -0,0 +1,141 @@ +# +# (C) Copyright 2006-2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# (C) Copyright 2008 +# Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +CONFIG_NAND_SPL = y + +include $(TOPDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds +LDFLAGS = -Bstatic -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL + +SOBJS = start.o _udivsi3.o _divsi3.o +COBJS = cpu.o davinci_nand.o ns16550.o div0.o davinci_pinmux.o psc.o \ + misc.o hawkboard_nand_spl.o nand_boot.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +nandobj := $(OBJTREE)/nand_spl/ + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin \ + $(nandobj)u-boot-spl-16k.bin + +all: $(ALL) + +$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +$(nandobj)u-boot.lds: $(LDSCRIPT) + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ + +# create symbolic links for common files + +# from board directory +$(obj)davinci_pinmux.c: + @rm -f $@ + @ln -s $(TOPDIR)/board/davinci/common/davinci_pinmux.c $@ + +# from drivers/mtd/nand directory +$(obj)davinci_nand.c: + @rm -f $@ + @ln -s $(TOPDIR)/drivers/mtd/nand/davinci_nand.c $@ + +# from nand_spl directory +$(obj)nand_boot.c: + @rm -f $@ + @ln -s $(TOPDIR)/nand_spl/nand_boot.c $@ + +# from drivers/serial directory +$(obj)ns16550.c: + @rm -f $@ + @ln -sf $(TOPDIR)/drivers/serial/ns16550.c $@ + +# from cpu directory +$(obj)start.S: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/start.S $@ + +# from lib directory +$(obj)_udivsi3.S: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/lib/_udivsi3.S $@ + +# from lib directory +$(obj)_divsi3.S: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/lib/_divsi3.S $@ + +# from lib directory +$(obj)div0.c: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/lib/div0.c $@ + +# from SoC directory +$(obj)cpu.c: + @rm -f $@ + @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/cpu.c $@ + +# from board directory +$(obj)hawkboard_nand_spl.c: + @rm -f $@ + ln -s $(TOPDIR)/board/davinci/da8xxevm/hawkboard_nand_spl.c $@ + +# from board directory +$(obj)misc.c: + @rm -f $@ + ln -s $(TOPDIR)/board/davinci/common/misc.c $@ + +$(obj)psc.c: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/psc.c $@ + + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/davinci/da8xxevm/u-boot.lds b/nand_spl/board/davinci/da8xxevm/u-boot.lds new file mode 100644 index 0000000..f6ccf08 --- /dev/null +++ b/nand_spl/board/davinci/da8xxevm/u-boot.lds @@ -0,0 +1,75 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de> + * + * (C) Copyright 2008 + * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0xc1080000; + + . = ALIGN(4); + .text : + { + start.o (.text) + cpu.o (.text) + nand_boot.o (.text) + + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { + *(.data) + __datarel_start = .; + *(.data.rel) + __datarelrolocal_start = .; + *(.data.rel.ro.local) + __datarellocal_start = .; + *(.data.rel.local) + __datarelro_start = .; + *(.data.rel.ro) + } + + . = ALIGN(4); + __rel_dyn_start = .; + __rel_dyn_end = .; + __dynsym_start = .; + + __got_start = .; + . = ALIGN(4); + .got : { *(.got) } + + __got_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/nand_spl/board/samsung/smdk6400/Makefile b/nand_spl/board/samsung/smdk6400/Makefile index 2111e57..18cee10 100644 --- a/nand_spl/board/samsung/smdk6400/Makefile +++ b/nand_spl/board/samsung/smdk6400/Makefile @@ -35,7 +35,7 @@ AFLAGS += -DCONFIG_NAND_SPL CFLAGS += -DCONFIG_NAND_SPL SOBJS = start.o cpu_init.o lowlevel_init.o -COBJS = nand_boot.o nand_ecc.o s3c64xx.o +COBJS = nand_boot.o nand_ecc.o s3c64xx.o smdk6400_nand_spl.o SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) @@ -93,6 +93,10 @@ $(obj)s3c64xx.c: @rm -f $@ @ln -s $(TOPDIR)/drivers/mtd/nand/s3c64xx.c $@ +$(obj)smdk6400_nand_spl.c: + @rm -f $@ + @ln -s $(TOPDIR)/board/samsung/smdk6400/smdk6400_nand_spl.c $@ + ######################################################################### $(obj)%.o: $(obj)%.S diff --git a/nand_spl/nand_boot.c b/nand_spl/nand_boot.c index d624418..76b8566 100644 --- a/nand_spl/nand_boot.c +++ b/nand_spl/nand_boot.c @@ -221,14 +221,6 @@ static int nand_load(struct mtd_info *mtd, unsigned int offs, return 0; } -#if defined(CONFIG_ARM) -void board_init_f (ulong bootflag) -{ - relocate_code (CONFIG_SYS_TEXT_BASE - TOTAL_MALLOC_LEN, NULL, - CONFIG_SYS_TEXT_BASE); -} -#endif - /* * The main entry for NAND booting. It's necessary that SDRAM is already * configured and available since this code loads the main U-Boot image @@ -244,6 +236,7 @@ void nand_boot(void) /* * Init board specific nand support */ + nand_chip.select_chip = NULL; nand_info.priv = &nand_chip; nand_chip.IO_ADDR_R = nand_chip.IO_ADDR_W = (void __iomem *)CONFIG_SYS_NAND_BASE; nand_chip.dev_ready = NULL; /* preset to NULL */ |