summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/freescale/t2080qds/Makefile12
-rw-r--r--board/freescale/t2080qds/ddr.c127
-rw-r--r--board/freescale/t2080qds/ddr.h85
-rw-r--r--board/freescale/t2080qds/eth_t2080qds.c511
-rw-r--r--board/freescale/t2080qds/law.c34
-rw-r--r--board/freescale/t2080qds/pci.c23
-rw-r--r--board/freescale/t2080qds/t2080qds.c324
-rw-r--r--board/freescale/t2080qds/t2080qds.h13
-rw-r--r--board/freescale/t2080qds/t2080qds_qixis.h47
-rw-r--r--board/freescale/t2080qds/tlb.c146
-rw-r--r--boards.cfg1
-rw-r--r--include/configs/T2080QDS.h803
12 files changed, 2126 insertions, 0 deletions
diff --git a/board/freescale/t2080qds/Makefile b/board/freescale/t2080qds/Makefile
new file mode 100644
index 0000000..0b8747b
--- /dev/null
+++ b/board/freescale/t2080qds/Makefile
@@ -0,0 +1,12 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_T2080QDS) += t2080qds.o
+obj-$(CONFIG_T2080QDS) += eth_t2080qds.o
+obj-$(CONFIG_PCI) += pci.o
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
diff --git a/board/freescale/t2080qds/ddr.c b/board/freescale/t2080qds/ddr.c
new file mode 100644
index 0000000..5db5d21
--- /dev/null
+++ b/board/freescale/t2080qds/ddr.c
@@ -0,0 +1,127 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 or later as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 2) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ /*
+ * we use identical timing for all slots. If needed, change the code
+ * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+ */
+ if (popts->registered_dimm_en)
+ pbsp = rdimms[0];
+ else
+ pbsp = udimms[0];
+
+
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ popts->twot_en = pbsp->force_2t;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found");
+ printf("for data rate %lu MT/s\n", ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->cpo_override = pbsp_highest->cpo;
+ popts->write_data_delay = pbsp_highest->write_data_delay;
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ popts->twot_en = pbsp_highest->force_2t;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
+ "wrlvl_ctrl_3 0x%x\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+ pbsp->wrlvl_ctl_3);
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ puts(" DDR: ");
+ return dram_size;
+}
diff --git a/board/freescale/t2080qds/ddr.h b/board/freescale/t2080qds/ddr.h
new file mode 100644
index 0000000..964eaad
--- /dev/null
+++ b/board/freescale/t2080qds/ddr.h
@@ -0,0 +1,85 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2t;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0},
+ {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0},
+ {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0},
+ {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
+ {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
+ {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
+ {1, 1800, 2, 5, 6, 0x06070709, 0x110a0b08, 0xff, 2, 0},
+ {1, 1866, 2, 4, 6, 0x06060708, 0x09090a07, 0xff, 2, 0},
+ {1, 1900, 2, 4, 6, 0x06060708, 0x09090a07, 0xff, 2, 0},
+ {1, 2000, 2, 4, 8, 0x090a0b0d, 0x0e0f110b, 0xff, 2, 0},
+ {1, 2133, 2, 4, 8, 0x090a0b0d, 0x0e0f110b, 0xff, 2, 0},
+ {}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {4, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0},
+ {4, 1666, 0, 5, 11, 0x0a080706, 0x07090906, 0xff, 2, 0},
+ {4, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0},
+ {2, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0},
+ {2, 1666, 0, 5, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0},
+ {2, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0},
+ {1, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0},
+ {1, 1666, 0, 5, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0},
+ {1, 2140, 0, 4, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0},
+ {}
+};
+
+/*
+ * The three slots have slightly different timing. The center values are good
+ * for all slots. We use identical speed tables for them. In future use, if
+ * DIMMs require separated tables, make more entries as needed.
+ */
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+/*
+ * The three slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+};
+
+
+#endif
diff --git a/board/freescale/t2080qds/eth_t2080qds.c b/board/freescale/t2080qds/eth_t2080qds.c
new file mode 100644
index 0000000..3613f93
--- /dev/null
+++ b/board/freescale/t2080qds/eth_t2080qds.c
@@ -0,0 +1,511 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+#include "../common/qixis.h"
+#include "../common/fman.h"
+#include "t2080qds_qixis.h"
+
+#define EMI_NONE 0xFFFFFFFF
+#define EMI1_RGMII1 0
+#define EMI1_RGMII2 1
+#define EMI1_SLOT1 2
+#define EMI1_SLOT2 6
+#define EMI1_SLOT3 3
+#define EMI1_SLOT4 4
+#define EMI1_SLOT5 5
+#define EMI2 7
+
+static int mdio_mux[NUM_FM_PORTS];
+
+static const char * const mdio_names[] = {
+ "T2080QDS_MDIO_RGMII1",
+ "T2080QDS_MDIO_RGMII2",
+ "T2080QDS_MDIO_SLOT1",
+ "T2080QDS_MDIO_SLOT3",
+ "T2080QDS_MDIO_SLOT4",
+ "T2080QDS_MDIO_SLOT5",
+ "T2080QDS_MDIO_SLOT2",
+ "T2080QDS_MDIO_10GC",
+};
+
+/* Map SerDes1 8 lanes to default slot, will be initialized dynamically */
+static u8 lane_to_slot[] = {3, 3, 3, 3, 1, 1, 1, 1};
+
+static const char *T2080qds_mdio_name_for_muxval(u8 muxval)
+{
+ return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+ struct mii_dev *bus;
+ const char *name = T2080qds_mdio_name_for_muxval(muxval);
+
+ if (!name) {
+ printf("No bus for muxval %x\n", muxval);
+ return NULL;
+ }
+
+ bus = miiphy_get_dev_by_name(name);
+
+ if (!bus) {
+ printf("No bus by name %s\n", name);
+ return NULL;
+ }
+
+ return bus;
+}
+
+struct T2080qds_mdio {
+ u8 muxval;
+ struct mii_dev *realbus;
+};
+
+static void T2080qds_mux_mdio(u8 muxval)
+{
+ u8 brdcfg4;
+ if (muxval < 7) {
+ brdcfg4 = QIXIS_READ(brdcfg[4]);
+ brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+ brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+ QIXIS_WRITE(brdcfg[4], brdcfg4);
+ }
+}
+
+static int T2080qds_mdio_read(struct mii_dev *bus, int addr, int devad,
+ int regnum)
+{
+ struct T2080qds_mdio *priv = bus->priv;
+
+ T2080qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int T2080qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+ int regnum, u16 value)
+{
+ struct T2080qds_mdio *priv = bus->priv;
+
+ T2080qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int T2080qds_mdio_reset(struct mii_dev *bus)
+{
+ struct T2080qds_mdio *priv = bus->priv;
+
+ return priv->realbus->reset(priv->realbus);
+}
+
+static int T2080qds_mdio_init(char *realbusname, u8 muxval)
+{
+ struct T2080qds_mdio *pmdio;
+ struct mii_dev *bus = mdio_alloc();
+
+ if (!bus) {
+ printf("Failed to allocate T2080QDS MDIO bus\n");
+ return -1;
+ }
+
+ pmdio = malloc(sizeof(*pmdio));
+ if (!pmdio) {
+ printf("Failed to allocate T2080QDS private data\n");
+ free(bus);
+ return -1;
+ }
+
+ bus->read = T2080qds_mdio_read;
+ bus->write = T2080qds_mdio_write;
+ bus->reset = T2080qds_mdio_reset;
+ sprintf(bus->name, T2080qds_mdio_name_for_muxval(muxval));
+
+ pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+ if (!pmdio->realbus) {
+ printf("No bus with name %s\n", realbusname);
+ free(bus);
+ free(pmdio);
+ return -1;
+ }
+
+ pmdio->muxval = muxval;
+ bus->priv = pmdio;
+
+ return mdio_register(bus);
+}
+
+void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
+ enum fm_port port, int offset)
+{
+ int phy;
+ char alias[20];
+ struct fixed_link f_link;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
+ phy = fm_info_get_phy_address(port);
+ switch (port) {
+ case FM1_DTSEC1:
+ case FM1_DTSEC2:
+ case FM1_DTSEC9:
+ case FM1_DTSEC10:
+ sprintf(alias, "phy_sgmii_s3_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot3");
+ break;
+ case FM1_DTSEC5:
+ case FM1_DTSEC6:
+ if (mdio_mux[port] == EMI1_SLOT1) {
+ sprintf(alias, "phy_sgmii_s1_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot1");
+ } else if (mdio_mux[port] == EMI1_SLOT2) {
+ sprintf(alias, "phy_sgmii_s2_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot2");
+ }
+ break;
+ default:
+ break;
+ }
+
+ } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
+ switch (srds_s1) {
+ case 0x66: /* XFI interface */
+ case 0x6b:
+ case 0x6c:
+ case 0x6d:
+ case 0x71:
+ f_link.phy_id = port;
+ f_link.duplex = 1;
+ f_link.link_speed = 10000;
+ f_link.pause = 0;
+ f_link.asym_pause = 0;
+ /* no PHY for XFI */
+ fdt_delprop(fdt, offset, "phy-handle");
+ fdt_setprop(fdt, offset, "fixed-link", &f_link,
+ sizeof(f_link));
+ break;
+ default:
+ break;
+ }
+ }
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+ return;
+}
+
+/*
+ * This function reads RCW to check if Serdes1{E,F,G,H} is configured
+ * as slot 1/2/3 and update the lane_to_slot[] array accordingly
+ */
+static void initialize_lane_to_slot(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ switch (srds_s1) {
+ case 0x51:
+ case 0x5f:
+ case 0x65:
+ case 0x6b:
+ case 0x71:
+ lane_to_slot[5] = 2;
+ lane_to_slot[6] = 2;
+ lane_to_slot[7] = 2;
+ break;
+ case 0xa6:
+ case 0x8e:
+ case 0x8f:
+ case 0x82:
+ case 0x83:
+ case 0xd3:
+ case 0xd9:
+ case 0xcb:
+ lane_to_slot[6] = 2;
+ lane_to_slot[7] = 2;
+ break;
+ case 0xda:
+ lane_to_slot[4] = 3;
+ lane_to_slot[5] = 3;
+ lane_to_slot[6] = 3;
+ lane_to_slot[7] = 3;
+ break;
+ default:
+ break;
+ }
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+ int i, idx, lane, slot, interface;
+ struct memac_mdio_info dtsec_mdio_info;
+ struct memac_mdio_info tgec_mdio_info;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 rcwsr13 = in_be32(&gur->rcwsr[13]);
+ u32 srds_s1;
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ initialize_lane_to_slot();
+
+ /* Initialize the mdio_mux array so we can recognize empty elements */
+ for (i = 0; i < NUM_FM_PORTS; i++)
+ mdio_mux[i] = EMI_NONE;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the 10G MDIO bus */
+ fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+ /* Register the muxing front-ends to the MDIO buses */
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
+ T2080qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
+
+ /* Set the two on-board RGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
+ if ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) ==
+ FSL_CORENET_RCWSR13_EC2_DTSEC4_RGMII)
+ fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
+ else
+ fm_info_set_phy_address(FM1_DTSEC10, RGMII_PHY2_ADDR);
+
+ switch (srds_s1) {
+ case 0x1c:
+ case 0x95:
+ case 0xa2:
+ case 0x94:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
+ break;
+ case 0x51:
+ case 0x5f:
+ case 0x65:
+ /* XAUI/HiGig in Slot3 */
+ fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
+ break;
+ case 0x66:
+ /*
+ * XFI does not need a PHY to work, but to avoid U-boot use
+ * default PHY address which is zero to a MAC when it found
+ * a MAC has no PHY address, we give a PHY address to XFI
+ * MAC, and should not use a real XAUI PHY address, since
+ * MDIO can access it successfully, and then MDIO thinks
+ * the XAUI card is used for the XFI MAC, which will cause
+ * error.
+ */
+ fm_info_set_phy_address(FM1_10GEC1, 4);
+ fm_info_set_phy_address(FM1_10GEC2, 5);
+ fm_info_set_phy_address(FM1_10GEC3, 6);
+ fm_info_set_phy_address(FM1_10GEC4, 7);
+ break;
+ case 0x6b:
+ fm_info_set_phy_address(FM1_10GEC1, 4);
+ fm_info_set_phy_address(FM1_10GEC2, 5);
+ fm_info_set_phy_address(FM1_10GEC3, 6);
+ fm_info_set_phy_address(FM1_10GEC4, 7);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0x6c:
+ case 0x6d:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0x71:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0xa6:
+ case 0x8e:
+ case 0x8f:
+ case 0x82:
+ case 0x83:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0xa4:
+ case 0x96:
+ case 0x8a:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ break;
+ case 0xd9:
+ case 0xd3:
+ case 0xcb:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ default:
+ puts("Invalid SerDes1 protocol for T2080QDS\n");
+ break;
+ }
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ idx = i - FM1_DTSEC1;
+ interface = fm_info_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_SGMII:
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_FM1_DTSEC1 + idx);
+ if (lane < 0)
+ break;
+ slot = lane_to_slot[lane];
+ debug("FM1@DTSEC%u expects SGMII in slot %u\n",
+ idx + 1, slot);
+ if (QIXIS_READ(present2) & (1 << (slot - 1)))
+ fm_disable_port(i);
+
+ switch (slot) {
+ case 1:
+ mdio_mux[i] = EMI1_SLOT1;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ case 2:
+ mdio_mux[i] = EMI1_SLOT2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ };
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ if (i == FM1_DTSEC3)
+ mdio_mux[i] = EMI1_RGMII1;
+ else if (i == FM1_DTSEC4 || FM1_DTSEC10)
+ mdio_mux[i] = EMI1_RGMII2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+ break;
+ default:
+ break;
+ }
+ }
+
+ for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+ idx = i - FM1_10GEC1;
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_XGMII:
+ if (srds_s1 == 0x51) {
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ XAUI_FM1_MAC9 + idx);
+ } else if ((srds_s1 == 0x5f) || (srds_s1 == 0x65)) {
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ HIGIG_FM1_MAC9 + idx);
+ } else {
+ if (i == FM1_10GEC1 || i == FM1_10GEC2)
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ XFI_FM1_MAC9 + idx);
+ else
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ XFI_FM1_MAC1 + idx);
+ }
+
+ if (lane < 0)
+ break;
+ mdio_mux[i] = EMI2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+
+ if ((srds_s1 == 0x66) || (srds_s1 == 0x6b) ||
+ (srds_s1 == 0x6c) || (srds_s1 == 0x6d) ||
+ (srds_s1 == 0x71)) {
+ /* As XFI is in cage intead of a slot, so
+ * ensure doesn't disable the corresponding port
+ */
+ break;
+ }
+
+ slot = lane_to_slot[lane];
+ if (QIXIS_READ(present2) & (1 << (slot - 1)))
+ fm_disable_port(i);
+ break;
+ default:
+ break;
+ }
+ }
+
+ cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+ return pci_eth_init(bis);
+}
diff --git a/board/freescale/t2080qds/law.c b/board/freescale/t2080qds/law.c
new file mode 100644
index 0000000..74e2a53
--- /dev/null
+++ b/board/freescale/t2080qds/law.c
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2008-2012 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef QIXIS_BASE_PHYS
+ SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ /* Limit DCSR to 32M to access NPC Trace Buffer */
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t2080qds/pci.c b/board/freescale/t2080qds/pci.c
new file mode 100644
index 0000000..84a89da
--- /dev/null
+++ b/board/freescale/t2080qds/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2007-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t2080qds/t2080qds.c b/board/freescale/t2080qds/t2080qds.c
new file mode 100644
index 0000000..cac32fe
--- /dev/null
+++ b/board/freescale/t2080qds/t2080qds.c
@@ -0,0 +1,324 @@
+/*
+ * Copyright 2009-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "../common/qixis.h"
+#include "../common/vsc3316_3308.h"
+#include "t2080qds.h"
+#include "t2080qds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ char buf[64];
+ u8 sw;
+ struct cpu_type *cpu = gd->arch.cpu;
+ static const char *freq[4] = {
+ "100.00MHZ(from 8T49N222A)", "125.00MHz",
+ "156.25MHZ", "100.00MHz"
+ };
+
+ printf("Board: %sQDS, ", cpu->name);
+ sw = QIXIS_READ(arch);
+ printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
+ printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);
+
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+ if (sw < 0x8)
+ printf("vBank%d\n", sw);
+ else if (sw == 0x8)
+ puts("Promjet\n");
+ else if (sw == 0x9)
+ puts("NAND\n");
+ else
+ printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+
+ printf("FPGA: v%d (%s), build %d", (int)QIXIS_READ(scver),
+ qixis_read_tag(buf), (int)qixis_read_minor());
+ /* the timestamp string contains "\n" at the end */
+ printf(" on %s", qixis_read_time(buf));
+
+ puts("SERDES Reference Clocks:\n");
+ sw = QIXIS_READ(brdcfg[2]);
+ printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[sw >> 6],
+ freq[(sw >> 4) & 0x3]);
+ printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[(sw & 0xf) >> 2],
+ freq[sw & 0x3]);
+
+ return 0;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+int brd_mux_lane_to_slot(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_prtcl_s1, srds_prtcl_s2;
+
+ srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+ srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+ srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+
+ switch (srds_prtcl_s1) {
+ case 0:
+ /* SerDes1 is not enabled */
+ break;
+ case 0x1c:
+ case 0x95:
+ case 0xa2:
+ case 0x94:
+ /* SD1(A:D) => SLOT3 SGMII
+ * SD1(G:H) => SLOT1 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x58);
+ break;
+ case 0x51:
+ /* SD1(A:D) => SLOT3 XAUI
+ * SD1(E) => SLOT1 PCIe4
+ * SD1(F:H) => SLOT2 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x15);
+ break;
+ case 0x66:
+ case 0x67:
+ /* SD1(A:D) => XFI cage
+ * SD1(E:H) => SLOT1 PCIe4
+ */
+ QIXIS_WRITE(brdcfg[12], 0xfe);
+ break;
+ case 0x6b:
+ /* SD1(A:D) => XFI cage
+ * SD1(E) => SLOT1 PCIe4
+ * SD1(F:H) => SLOT2 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0xf1);
+ break;
+ case 0x6c:
+ case 0x6d:
+ /* SD1(A:B) => XFI cage
+ * SD1(C:D) => SLOT3 SGMII
+ * SD1(E:H) => SLOT1 PCIe4
+ */
+ QIXIS_WRITE(brdcfg[12], 0xda);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes1 Protocol %d\n",
+ srds_prtcl_s1);
+ return -1;
+ }
+
+ switch (srds_prtcl_s2) {
+ case 0:
+ /* SerDes2 is not enabled */
+ break;
+ case 0x01:
+ case 0x02:
+ /* SD2(A:H) => SLOT4 PCIe1 */
+ QIXIS_WRITE(brdcfg[13], 0x20);
+ break;
+ case 0x15:
+ case 0x16:
+ /*
+ * SD2(A:D) => SLOT4 PCIe1
+ * SD2(E:F) => SLOT5 PCIe2
+ * SD2(G:H) => SATA1,SATA2
+ */
+ QIXIS_WRITE(brdcfg[13], 0xb0);
+ break;
+ case 0x18:
+ /*
+ * SD2(A:D) => SLOT4 PCIe1
+ * SD2(E:F) => SLOT5 Aurora
+ * SD2(G:H) => SATA1,SATA2
+ */
+ QIXIS_WRITE(brdcfg[13], 0x70);
+ break;
+ case 0x1f:
+ /*
+ * SD2(A:D) => SLOT4 PCIe1
+ * SD2(E:H) => SLOT5 PCIe2
+ */
+ QIXIS_WRITE(brdcfg[13], 0xa0);
+ break;
+ case 0x29:
+ case 0x2d:
+ case 0x2e:
+ /*
+ * SD2(A:D) => SLOT4 SRIO2
+ * SD2(E:H) => SLOT5 SRIO1
+ */
+ QIXIS_WRITE(brdcfg[13], 0x50);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes2 Protocol %d\n",
+ srds_prtcl_s2);
+ return -1;
+ }
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ /* Disable remote I2C connection to qixis fpga */
+ QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE);
+
+ brd_mux_lane_to_slot();
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+ /* use accurate clock measurement */
+ int freq = QIXIS_READ(clk_freq[0]) << 8 | QIXIS_READ(clk_freq[1]);
+ int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+ u32 val;
+
+ val = freq * base;
+ if (val) {
+ debug("SYS Clock measurement is: %d\n", val);
+ return val;
+ } else {
+ printf("Warning: SYS clock measurement is invalid, ");
+ printf("using value from brdcfg1.\n");
+ }
+#endif
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+ /* use accurate clock measurement */
+ int freq = QIXIS_READ(clk_freq[2]) << 8 | QIXIS_READ(clk_freq[3]);
+ int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+ u32 val;
+
+ val = freq * base;
+ if (val) {
+ debug("DDR Clock measurement is: %d\n", val);
+ return val;
+ } else {
+ printf("Warning: DDR clock measurement is invalid, ");
+ printf("using value from brdcfg1.\n");
+ }
+#endif
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+}
diff --git a/board/freescale/t2080qds/t2080qds.h b/board/freescale/t2080qds/t2080qds.h
new file mode 100644
index 0000000..39fcef2
--- /dev/null
+++ b/board/freescale/t2080qds/t2080qds.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2011-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CORENET_DS_H__
+#define __CORENET_DS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/t2080qds/t2080qds_qixis.h b/board/freescale/t2080qds/t2080qds_qixis.h
new file mode 100644
index 0000000..fc83da7
--- /dev/null
+++ b/board/freescale/t2080qds/t2080qds_qixis.h
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T2080QDS_QIXIS_H__
+#define __T2080QDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for T2080QDS */
+
+#define QIXIS_SRDS1CLK_122 0x5a
+#define QIXIS_SRDS1CLK_125 0x5e
+
+
+/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
+#define BRDCFG4_EMISEL_MASK 0xE0
+#define BRDCFG4_EMISEL_SHIFT 5
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_66 0x0
+#define QIXIS_SYSCLK_83 0x1
+#define QIXIS_SYSCLK_100 0x2
+#define QIXIS_SYSCLK_125 0x3
+#define QIXIS_SYSCLK_133 0x4
+#define QIXIS_SYSCLK_150 0x5
+#define QIXIS_SYSCLK_160 0x6
+#define QIXIS_SYSCLK_166 0x7
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_66 0x0
+#define QIXIS_DDRCLK_100 0x1
+#define QIXIS_DDRCLK_125 0x2
+#define QIXIS_DDRCLK_133 0x3
+
+#define BRDCFG5_IRE 0x20 /* i2c Remote i2c1 enable */
+
+#define BRDCFG12_SD3EN_MASK 0x20
+#define BRDCFG12_SD3MX_MASK 0x08
+#define BRDCFG12_SD3MX_SLOT5 0x08
+#define BRDCFG12_SD3MX_SLOT6 0x00
+#define BRDCFG12_SD4EN_MASK 0x04
+#define BRDCFG12_SD4MX_MASK 0x03
+#define BRDCFG12_SD4MX_SLOT7 0x02
+#define BRDCFG12_SD4MX_SLOT8 0x01
+#define BRDCFG12_SD4MX_AURO_SATA 0x00
+#endif
diff --git a/board/freescale/t2080qds/tlb.c b/board/freescale/t2080qds/tlb.c
new file mode 100644
index 0000000..62cd110
--- /dev/null
+++ b/board/freescale/t2080qds/tlb.c
@@ -0,0 +1,146 @@
+/*
+ * Copyright 2008-2013 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+ * SRAM is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+ /*
+ * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the
+ * space is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR,
+ CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCIe 1, 0x80000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_512M, 1),
+
+ /* *I*G* - PCIe 2, 0xa0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCIe 3, 0xb0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+
+ /* *I*G* - PCIe 4, 0xc0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE4_MEM_VIRT, CONFIG_SYS_PCIE4_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 11, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 13, BOOKE_PAGESZ_32M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ /*
+ * *I*G - NAND
+ * entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so we use entry 16 for nand.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 16, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef QIXIS_BASE_PHYS
+ SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 17, BOOKE_PAGESZ_4K, 1),
+#endif
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+ /*
+ * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for
+ * fetching ucode and ENV from master
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR,
+ CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 18, BOOKE_PAGESZ_1M, 1),
+#endif
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index d9b0a9a..21e00f5 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -965,6 +965,7 @@ Active powerpc mpc85xx - freescale t4qds
Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Poonam Aggrwal <poonam.aggrwal@freescale.com>
Active powerpc mpc85xx - freescale t104xrdb T1040RDB T1040RDB:PPC_T1040 Poonam Aggrwal <poonam.aggrwal@freescale.com>
Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T1042RDB_PI:PPC_T1042 Poonam Aggrwal <poonam.aggrwal@freescale.com>
+Active powerpc mpc85xx - freescale t2080qds T2080QDS T2080QDS:PPC_T2080
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach@gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach@gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach@gdsys.de>
diff --git a/include/configs/T2080QDS.h b/include/configs/T2080QDS.h
new file mode 100644
index 0000000..f85ccf5
--- /dev/null
+++ b/include/configs/T2080QDS.h
@@ -0,0 +1,803 @@
+/*
+ * Copyright 2011-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * T2080 QDS board configuration file
+ */
+
+#ifndef __T2080QDS_H
+#define __T2080QDS_H
+
+#define CONFIG_T2080QDS
+#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
+#define CONFIG_MMC
+#define CONFIG_SPI_FLASH
+#define CONFIG_USB_EHCI
+#define CONFIG_FSL_SATA_V2
+#define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */
+#define CONFIG_SRIO1 /* SRIO port 1 */
+#define CONFIG_SRIO2 /* SRIO port 2 */
+
+/* High Level Configuration Options */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */
+#define CONFIG_MP /* support multiple processors */
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#endif
+
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#ifdef CONFIG_SYS_NO_FLASH
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 1105)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR 0xffe20000
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+#define CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
+#define CTRL_INTLV_PREFERED cacheline
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE 0xe0000000
+#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_FSL_QIXIS /* use common QIXIS code */
+#define QIXIS_BASE 0xffdf0000
+#define QIXIS_LBMAP_SWITCH 6
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_ALTBANK 0x04
+#define QIXIS_RST_CTL_RESET 0x83
+#define QIXIS_RST_FORCE_MEM 0x1
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
+
+#define CONFIG_SYS_CSPR3_EXT (0xf)
+#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
+#define CONFIG_SYS_CSOR3 0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3 0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */\
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#endif
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
+#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
+#define CONFIG_SYS_FSL_I2C_SPEED 100000
+#define CONFIG_SYS_FSL_I2C2_SPEED 100000
+#define CONFIG_SYS_FSL_I2C3_SPEED 100000
+#define CONFIG_SYS_FSL_I2C4_SPEED 100000
+#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
+#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
+#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
+#define I2C_MUX_CH_DEFAULT 0x8
+
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
+#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+#endif
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_PCIE4 /* PCIE controler 4 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 4, Base address 203000 */
+#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */
+#define CONFIG_NET_MULTI
+#define CONFIG_E1000
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 18
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 18
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_DPAA_RMAN /* RMan */
+#define CONFIG_SYS_INTERLAKEN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR 0x1
+#define RGMII_PHY2_ADDR 0x2
+#define FM1_10GEC1_PHY_ADDR 0x3
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC3"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * SATA
+ */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_HAS_FSL_DR_USB
+#endif
+
+/*
+ * SDHC
+ */
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_BDI
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#define __USB_PHY_TYPE utmi
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:" \
+ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
+ "bank_intlv=auto;" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=t2080qds/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=t2080qds/t2080qds.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+/*
+ * For emulation this causes u-boot to jump to the start of the
+ * proof point app code automatically
+ */
+#define CONFIG_PROOF_POINTS \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x29000000 - - -;" \
+ "cpu 2 release 0x29000000 - - -;" \
+ "cpu 3 release 0x29000000 - - -;" \
+ "cpu 4 release 0x29000000 - - -;" \
+ "cpu 5 release 0x29000000 - - -;" \
+ "cpu 6 release 0x29000000 - - -;" \
+ "cpu 7 release 0x29000000 - - -;" \
+ "go 0x29000000"
+
+#define CONFIG_HVBOOT \
+ "setenv bootargs config-addr=0x60000000; " \
+ "bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x01000000 - - -;" \
+ "cpu 2 release 0x01000000 - - -;" \
+ "cpu 3 release 0x01000000 - - -;" \
+ "cpu 4 release 0x01000000 - - -;" \
+ "cpu 5 release 0x01000000 - - -;" \
+ "cpu 6 release 0x01000000 - - -;" \
+ "cpu 7 release 0x01000000 - - -;" \
+ "go 0x01000000"
+
+#define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#undef CONFIG_CMD_USB
+#endif
+
+#endif /* __T2080QDS_H */