diff options
237 files changed, 3086 insertions, 1951 deletions
@@ -65,11 +65,9 @@ endif # the object files are placed in the source directory. # -ifdef O ifeq ("$(origin O)", "command line") BUILD_DIR := $(O) endif -endif # Call a source code checker (by default, "sparse") as part of the # C compilation. @@ -231,87 +229,71 @@ OBJS := $(addprefix $(obj),$(OBJS)) HAVE_VENDOR_COMMON_LIB = $(if $(wildcard board/$(VENDOR)/common/Makefile),y,n) -LIBS-y += lib/libgeneric.o -LIBS-y += lib/rsa/librsa.o -LIBS-y += lib/lzma/liblzma.o -LIBS-y += lib/lzo/liblzo.o -LIBS-y += lib/zlib/libz.o -LIBS-$(CONFIG_TIZEN) += lib/tizen/libtizen.o -LIBS-$(HAVE_VENDOR_COMMON_LIB) += board/$(VENDOR)/common/lib$(VENDOR).o -LIBS-y += $(CPUDIR)/lib$(CPU).o +LIBS-y += lib/ +LIBS-$(CONFIG_RSA) += lib/rsa/ +LIBS-$(CONFIG_LZMA) += lib/lzma/ +LIBS-$(CONFIG_LZO) += lib/lzo/ +LIBS-$(CONFIG_ZLIB) += lib/zlib/ +LIBS-$(CONFIG_TIZEN) += lib/tizen/ +LIBS-$(HAVE_VENDOR_COMMON_LIB) += board/$(VENDOR)/common/ +LIBS-y += $(CPUDIR)/ ifdef SOC -LIBS-y += $(CPUDIR)/$(SOC)/lib$(SOC).o -endif -ifeq ($(CPU),ixp) -LIBS-y += drivers/net/npe/libnpe.o -endif -LIBS-$(CONFIG_OF_EMBED) += dts/libdts.o -LIBS-y += arch/$(ARCH)/lib/lib$(ARCH).o -LIBS-y += fs/libfs.o \ - fs/fat/libfat.o -LIBS-y += net/libnet.o -LIBS-y += disk/libdisk.o -LIBS-y += drivers/libdrivers.o -LIBS-y += drivers/dma/libdma.o -LIBS-y += drivers/gpio/libgpio.o -LIBS-y += drivers/i2c/libi2c.o -LIBS-y += drivers/input/libinput.o -LIBS-y += drivers/mmc/libmmc.o -LIBS-y += drivers/mtd/libmtd.o -LIBS-y += drivers/mtd/nand/libnand.o -LIBS-y += drivers/mtd/onenand/libonenand.o -LIBS-y += drivers/mtd/ubi/libubi.o -LIBS-y += drivers/mtd/spi/libspi_flash.o -LIBS-y += drivers/net/libnet.o -LIBS-y += drivers/net/phy/libphy.o -LIBS-y += drivers/pci/libpci.o -LIBS-y += drivers/power/libpower.o \ - drivers/power/fuel_gauge/libfuel_gauge.o \ - drivers/power/mfd/libmfd.o \ - drivers/power/pmic/libpmic.o \ - drivers/power/battery/libbattery.o -LIBS-y += drivers/spi/libspi.o -ifeq ($(CPU),mpc83xx) -LIBS-y += drivers/qe/libqe.o -LIBS-y += arch/powerpc/cpu/mpc8xxx/ddr/libddr.o -LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o -endif -ifeq ($(CPU),mpc85xx) -LIBS-y += drivers/qe/libqe.o -LIBS-y += drivers/net/fm/libfm.o -LIBS-y += arch/powerpc/cpu/mpc8xxx/ddr/libddr.o -LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o -endif -ifeq ($(CPU),mpc86xx) -LIBS-y += arch/powerpc/cpu/mpc8xxx/ddr/libddr.o -LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o -endif -LIBS-y += drivers/serial/libserial.o -LIBS-y += drivers/usb/eth/libusb_eth.o -LIBS-y += drivers/usb/gadget/libusb_gadget.o -LIBS-y += drivers/usb/host/libusb_host.o -LIBS-y += drivers/usb/musb/libusb_musb.o -LIBS-y += drivers/usb/musb-new/libusb_musb-new.o -LIBS-y += drivers/usb/phy/libusb_phy.o -LIBS-y += drivers/usb/ulpi/libusb_ulpi.o -LIBS-y += common/libcommon.o -LIBS-y += lib/libfdt/libfdt.o -LIBS-y += api/libapi.o -LIBS-y += post/libpost.o -LIBS-y += test/libtest.o +LIBS-y += $(CPUDIR)/$(SOC)/ +endif +LIBS-$(CONFIG_IXP4XX_NPE) += drivers/net/npe/ +LIBS-$(CONFIG_OF_EMBED) += dts/ +LIBS-y += arch/$(ARCH)/lib/ +LIBS-y += fs/ +LIBS-y += net/ +LIBS-y += disk/ +LIBS-y += drivers/ +LIBS-y += drivers/dma/ +LIBS-y += drivers/gpio/ +LIBS-y += drivers/i2c/ +LIBS-y += drivers/input/ +LIBS-y += drivers/mmc/ +LIBS-y += drivers/mtd/ +LIBS-y += drivers/mtd/nand/ +LIBS-y += drivers/mtd/onenand/ +LIBS-y += drivers/mtd/ubi/ +LIBS-y += drivers/mtd/spi/ +LIBS-y += drivers/net/ +LIBS-y += drivers/net/phy/ +LIBS-y += drivers/pci/ +LIBS-y += drivers/power/ \ + drivers/power/fuel_gauge/ \ + drivers/power/mfd/ \ + drivers/power/pmic/ \ + drivers/power/battery/ +LIBS-y += drivers/spi/ +LIBS-$(CONFIG_FMAN_ENET) += drivers/net/fm/ +LIBS-y += drivers/serial/ +LIBS-y += drivers/usb/eth/ +LIBS-y += drivers/usb/gadget/ +LIBS-y += drivers/usb/host/ +LIBS-y += drivers/usb/musb/ +LIBS-y += drivers/usb/musb-new/ +LIBS-y += drivers/usb/phy/ +LIBS-y += drivers/usb/ulpi/ +LIBS-y += common/ +LIBS-y += lib/libfdt/ +LIBS-y += api/ +LIBS-y += post/ +LIBS-y += test/ ifneq (,$(filter $(SOC), mx25 mx27 mx5 mx6 mx31 mx35 mxs vf610)) -LIBS-y += arch/$(ARCH)/imx-common/libimx-common.o +LIBS-y += arch/$(ARCH)/imx-common/ endif -LIBS-$(CONFIG_ARM) += arch/arm/cpu/libcpu.o +LIBS-$(CONFIG_ARM) += arch/arm/cpu/ +LIBS-$(CONFIG_PPC) += arch/powerpc/cpu/ +LIBS-y += board/$(BOARDDIR)/ + +LIBS-y := $(patsubst %/, %/built-in.o, $(LIBS-y)) LIBS := $(addprefix $(obj),$(sort $(LIBS-y))) .PHONY : $(LIBS) -LIBBOARD = board/$(BOARDDIR)/lib$(BOARD).o -LIBBOARD := $(addprefix $(obj),$(LIBBOARD)) - # Add GCC lib ifdef USE_PRIVATE_LIBGCC ifeq ("$(USE_PRIVATE_LIBGCC)", "yes") @@ -335,7 +317,7 @@ LDPPFLAGS += \ sed -ne 's/GNU ld version \([0-9][0-9]*\)\.\([0-9][0-9]*\).*/-DLD_MAJOR=\1 -DLD_MINOR=\2/p') __OBJS := $(subst $(obj),,$(OBJS)) -__LIBS := $(subst $(obj),,$(LIBS)) $(subst $(obj),,$(LIBBOARD)) +__LIBS := $(subst $(obj),,$(LIBS)) ######################################################################### ######################################################################### @@ -549,7 +531,7 @@ GEN_UBOOT = \ endif $(obj)u-boot: depend \ - $(SUBDIR_TOOLS) $(OBJS) $(LIBBOARD) $(LIBS) $(LDSCRIPT) $(obj)u-boot.lds + $(SUBDIR_TOOLS) $(OBJS) $(LIBS) $(LDSCRIPT) $(obj)u-boot.lds $(GEN_UBOOT) ifeq ($(CONFIG_KALLSYMS),y) smap=`$(call SYSTEM_MAP,$(obj)u-boot) | \ @@ -564,11 +546,6 @@ $(OBJS): $(LIBS): depend $(SUBDIR_TOOLS) $(MAKE) $(build) $(dir $(subst $(obj),,$@)) - mv $(dir $@)built-in.o $@ - -$(LIBBOARD): depend $(LIBS) - $(MAKE) $(build) $(dir $(subst $(obj),,$@)) - mv $(dir $@)built-in.o $@ $(SUBDIRS): depend $(MAKE) -C $@ all @@ -634,7 +611,7 @@ SYSTEM_MAP = \ grep -v '\(compiled\)\|\(\.o$$\)\|\( [aUw] \)\|\(\.\.ng$$\)\|\(LASH[RL]DI\)' | \ LC_ALL=C sort $(obj)System.map: $(obj)u-boot - @$(call SYSTEM_MAP,$<) > $(obj)System.map + @$(call SYSTEM_MAP,$<) > $@ checkthumb: @if test $(call cc-version) -lt 0404; then \ @@ -806,12 +783,6 @@ sinclude $(obj).boards.depend $(obj).boards.depend: boards.cfg @awk '(NF && $$1 !~ /^#/) { print $$7 ": " $$7 "_config; $$(MAKE)" }' $< > $@ -# -# Functions to generate common board directory names -# -lcname = $(shell echo $(1) | sed -e 's/\(.*\)_config/\L\1/') -ucname = $(shell echo $(1) | sed -e 's/\(.*\)_config/\U\1/') - ######################################################################### ######################################################################### @@ -888,8 +859,6 @@ clobber: tidy @rm -f $(obj)MLO MLO.byteswap @rm -f $(obj)SPL @rm -f $(obj)tools/xway-swap-bytes - @rm -f $(obj)arch/powerpc/cpu/mpc824x/bedbug_603e.c - @rm -f $(obj)arch/powerpc/cpu/mpc83xx/ddr-gen?.c @rm -fr $(obj)include/asm/proc $(obj)include/asm/arch $(obj)include/asm @rm -fr $(obj)include/generated @[ ! -d $(obj)nand_spl ] || find $(obj)nand_spl -name "*" -type l -print | xargs rm -f @@ -2040,6 +2040,42 @@ CBFS (Coreboot Filesystem) support - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3 - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses + - drivers/i2c/sh_i2c.c: + - activate this driver with CONFIG_SYS_I2C_SH + - This driver adds from 2 to 5 i2c buses + + - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0 + - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0 + - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1 + - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1 + - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2 + - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2 + - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3 + - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3 + - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4 + - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4 + - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5 + - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5 + - CONFIF_SYS_I2C_SH_NUM_CONTROLLERS for nummber of i2c buses + + - drivers/i2c/omap24xx_i2c.c + - activate this driver with CONFIG_SYS_I2C_OMAP24XX + - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0 + - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0 + - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1 + - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1 + - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2 + - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2 + - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3 + - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3 + - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4 + - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4 + + - drivers/i2c/zynq_i2c.c + - activate this driver with CONFIG_SYS_I2C_ZYNQ + - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting + - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr + additional defines: CONFIG_SYS_NUM_I2C_BUSES diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index bb77b5c..dfa3760 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -779,7 +779,8 @@ void gpi2c_init(void) static int gpi2c = 1; if (gpi2c) { - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, + CONFIG_SYS_OMAP24_I2C_SLAVE); gpi2c = 0; } } diff --git a/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds b/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds index 5e93b34..02aa129 100644 --- a/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds +++ b/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds @@ -33,6 +33,11 @@ SECTIONS .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram . = ALIGN(4); + .u_boot_list : { + KEEP(*(SORT(.u_boot_list*_i2c_*))); + } >.sram + + . = ALIGN(4); __image_copy_end = .; _end = .; diff --git a/arch/arm/cpu/armv7/omap3/board.c b/arch/arm/cpu/armv7/omap3/board.c index 7d1f8d9..2922816 100644 --- a/arch/arm/cpu/armv7/omap3/board.c +++ b/arch/arm/cpu/armv7/omap3/board.c @@ -98,7 +98,7 @@ void spl_board_init(void) gpmc_init(); #endif #ifdef CONFIG_SPL_I2C_SUPPORT - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif } #endif /* CONFIG_SPL_BUILD */ diff --git a/arch/arm/cpu/armv7/omap3/clock.c b/arch/arm/cpu/armv7/omap3/clock.c index 9f989ff..14fc7e8 100644 --- a/arch/arm/cpu/armv7/omap3/clock.c +++ b/arch/arm/cpu/armv7/omap3/clock.c @@ -708,7 +708,7 @@ void per_clocks_enable(void) sr32(&prcm_base->iclken_per, 17, 1, 1); #endif -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX /* Turn on all 3 I2C clocks */ sr32(&prcm_base->fclken1_core, 15, 3, 0x7); sr32(&prcm_base->iclken1_core, 15, 3, 0x7); /* I2C1,2,3 = on */ diff --git a/arch/arm/cpu/armv7/rmobile/Makefile b/arch/arm/cpu/armv7/rmobile/Makefile index 8f4cf3a..5e296c4 100644 --- a/arch/arm/cpu/armv7/rmobile/Makefile +++ b/arch/arm/cpu/armv7/rmobile/Makefile @@ -15,10 +15,4 @@ obj-$(CONFIG_R8A7740) += cpu_info-r8a7740.o obj-$(CONFIG_R8A7740) += pfc-r8a7740.o obj-$(CONFIG_SH73A0) += cpu_info-sh73a0.o obj-$(CONFIG_SH73A0) += pfc-sh73a0.o -obj-$(CONFIG_TMU_TIMER) += sh_timer.o - -SRCS += $(obj)sh_timer.c -# from arch/sh/lib/ directory -$(obj)sh_timer.c: - @rm -f $(obj)sh_timer.c - ln -s $(SRCTREE)/arch/sh/lib/time.c $(obj)sh_timer.c +obj-$(CONFIG_TMU_TIMER) += ../../../../sh/lib/time.o diff --git a/arch/arm/include/asm/arch-am33xx/i2c.h b/arch/arm/include/asm/arch-am33xx/i2c.h index 8bfa53f..8642c8f 100644 --- a/arch/arm/include/asm/arch-am33xx/i2c.h +++ b/arch/arm/include/asm/arch-am33xx/i2c.h @@ -4,8 +4,8 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef _I2C_H_ -#define _I2C_H_ +#ifndef _I2C_AM33XX_H_ +#define _I2C_AM33XX_H_ #define I2C_BASE1 0x44E0B000 #define I2C_BASE2 0x4802A000 @@ -62,4 +62,4 @@ struct i2c { #define I2C_IP_CLK 48000000 #define I2C_INTERNAL_SAMPLING_CLK 12000000 -#endif /* _I2C_H_ */ +#endif /* _I2C_AM33XX_H_ */ diff --git a/arch/microblaze/cpu/u-boot.lds b/arch/microblaze/cpu/u-boot.lds index 3e6204d..fdad207 100644 --- a/arch/microblaze/cpu/u-boot.lds +++ b/arch/microblaze/cpu/u-boot.lds @@ -30,7 +30,7 @@ SECTIONS { __data_start = .; #ifdef CONFIG_OF_EMBED - dts/libdts.o (.data) + dts/built-in.o (.data) #endif *(.data) __data_end = .; diff --git a/arch/powerpc/cpu/Makefile b/arch/powerpc/cpu/Makefile new file mode 100644 index 0000000..d630abe --- /dev/null +++ b/arch/powerpc/cpu/Makefile @@ -0,0 +1,3 @@ +ifneq ($(filter mpc83xx mpc85xx mpc86xx,$(CPU)),) +obj-y += mpc8xxx/ +endif diff --git a/arch/powerpc/cpu/mpc512x/Makefile b/arch/powerpc/cpu/mpc512x/Makefile index f770350..a4934ef 100644 --- a/arch/powerpc/cpu/mpc512x/Makefile +++ b/arch/powerpc/cpu/mpc512x/Makefile @@ -4,8 +4,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(OBJTREE)/board/freescale/common) - extra-y = start.o obj-y := cpu.o obj-y += traps.o diff --git a/arch/powerpc/cpu/mpc824x/.gitignore b/arch/powerpc/cpu/mpc824x/.gitignore deleted file mode 100644 index 2d79931..0000000 --- a/arch/powerpc/cpu/mpc824x/.gitignore +++ /dev/null @@ -1 +0,0 @@ -/bedbug_603e.c diff --git a/arch/powerpc/cpu/mpc824x/Makefile b/arch/powerpc/cpu/mpc824x/Makefile index 67b0d17..2c8be92 100644 --- a/arch/powerpc/cpu/mpc824x/Makefile +++ b/arch/powerpc/cpu/mpc824x/Makefile @@ -5,15 +5,7 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)drivers/epic $(obj)drivers/i2c) -endif - extra-y = start.o obj-y = traps.o cpu.o cpu_init.o interrupts.o speed.o \ drivers/epic/epic1.o drivers/i2c/i2c.o pci.o -obj-y += bedbug_603e.o - -SRCS += $(obj)bedbug_603e.c -$(obj)bedbug_603e.c: - ln -sf $(src)../mpc8260/bedbug_603e.c $(obj)bedbug_603e.c +obj-y += ../mpc8260/bedbug_603e.o diff --git a/arch/powerpc/cpu/mpc83xx/Makefile b/arch/powerpc/cpu/mpc83xx/Makefile index b7142f0..d3f7001 100644 --- a/arch/powerpc/cpu/mpc83xx/Makefile +++ b/arch/powerpc/cpu/mpc83xx/Makefile @@ -39,20 +39,10 @@ obj-$(CONFIG_OF_LIBFDT) += fdt.o obj-y += cache.o ifdef CONFIG_FSL_DDR2 -obj-$(CONFIG_MPC8349) += ddr-gen2.o -SRCS += $(obj)ddr-gen2.c +obj-$(CONFIG_MPC8349) += ../mpc85xx/ddr-gen2.o else obj-y += spd_sdram.o endif obj-$(CONFIG_FSL_DDR2) += law.o endif # not minimal - -$(obj)ddr-gen1.c: - ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/ddr-gen1.c $(obj)ddr-gen1.c - -$(obj)ddr-gen2.c: - ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/ddr-gen2.c $(obj)ddr-gen2.c - -$(obj)ddr-gen3.c: - ln -sf $(SRCTREE)/arch/powerpc/cpu/mpc85xx/ddr-gen3.c $(obj)ddr-gen3.c diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile index 50ddb50..a34014f 100644 --- a/arch/powerpc/cpu/mpc85xx/Makefile +++ b/arch/powerpc/cpu/mpc85xx/Makefile @@ -70,6 +70,9 @@ obj-$(CONFIG_PPC_B4860) += ddr-gen3.o obj-$(CONFIG_BSC9131) += ddr-gen3.o obj-$(CONFIG_BSC9132) += ddr-gen3.o obj-$(CONFIG_PPC_T1040) += ddr-gen3.o +obj-$(CONFIG_PPC_T1042) += ddr-gen3.o +obj-$(CONFIG_PPC_T1020) += ddr-gen3.o +obj-$(CONFIG_PPC_T1022) += ddr-gen3.o obj-$(CONFIG_CPM2) += ether_fcc.o obj-$(CONFIG_OF_LIBFDT) += fdt.o @@ -89,6 +92,10 @@ obj-$(CONFIG_PPC_T4160) += t4240_ids.o obj-$(CONFIG_PPC_B4420) += b4860_ids.o obj-$(CONFIG_PPC_B4860) += b4860_ids.o obj-$(CONFIG_PPC_T1040) += t1040_ids.o +obj-$(CONFIG_PPC_T1042) += t1040_ids.o +obj-$(CONFIG_PPC_T1020) += t1040_ids.o +obj-$(CONFIG_PPC_T1022) += t1040_ids.o + obj-$(CONFIG_QE) += qe_io.o obj-$(CONFIG_CPM2) += serial_scc.o @@ -128,6 +135,9 @@ obj-$(CONFIG_PPC_B4420) += b4860_serdes.o obj-$(CONFIG_PPC_B4860) += b4860_serdes.o obj-$(CONFIG_BSC9132) += bsc9132_serdes.o obj-$(CONFIG_PPC_T1040) += t1040_serdes.o +obj-$(CONFIG_PPC_T1042) += t1040_serdes.o +obj-$(CONFIG_PPC_T1020) += t1040_serdes.o +obj-$(CONFIG_PPC_T1022) += t1040_serdes.o obj-y += cpu.o obj-y += cpu_init.o diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c index 2ccd9c7..33bc900 100644 --- a/arch/powerpc/cpu/mpc85xx/fdt.c +++ b/arch/powerpc/cpu/mpc85xx/fdt.c @@ -586,6 +586,7 @@ void ft_cpu_setup(void *blob, bd_t *bd) { int off; int val; + int len; sys_info_t sysinfo; /* delete crypto node if not on an E-processor */ @@ -615,8 +616,8 @@ void ft_cpu_setup(void *blob, bd_t *bd) get_sys_info(&sysinfo); off = fdt_node_offset_by_prop_value(blob, -1, "device_type", "cpu", 4); while (off != -FDT_ERR_NOTFOUND) { - u32 *reg = (u32 *)fdt_getprop(blob, off, "reg", 0); - val = cpu_to_fdt32(sysinfo.freq_processor[*reg]); + u32 *reg = (u32 *)fdt_getprop(blob, off, "reg", &len); + val = cpu_to_fdt32(sysinfo.freq_processor[(*reg) / (len / 4)]); fdt_setprop(blob, off, "clock-frequency", &val, 4); off = fdt_node_offset_by_prop_value(blob, off, "device_type", "cpu", 4); diff --git a/arch/powerpc/cpu/mpc85xx/liodn.c b/arch/powerpc/cpu/mpc85xx/liodn.c index 4b00da9..19e130e 100644 --- a/arch/powerpc/cpu/mpc85xx/liodn.c +++ b/arch/powerpc/cpu/mpc85xx/liodn.c @@ -239,9 +239,9 @@ static void fdt_fixup_srio_liodn(void *blob, struct srio_liodn_id_table *tbl) #endif #define CONFIG_SYS_MAX_PCI_EPS 8 -#define CONFIG_SYS_PCI_EP_LIODN_START 256 -static void fdt_fixup_pci_liodn_offsets(void *fdt, const char *compat) +static void fdt_fixup_pci_liodn_offsets(void *fdt, const char *compat, + int ep_liodn_start) { int off, pci_idx = 0, pci_cnt = 0, i, rc; const uint32_t *base_liodn; @@ -271,7 +271,7 @@ static void fdt_fixup_pci_liodn_offsets(void *fdt, const char *compat) continue; } for (i = 0; i < CONFIG_SYS_MAX_PCI_EPS; i++) - liodn_offs[i + 1] = CONFIG_SYS_PCI_EP_LIODN_START + + liodn_offs[i + 1] = ep_liodn_start + i * pci_cnt + pci_idx - *base_liodn; rc = fdt_setprop(fdt, off, "fsl,liodn-offset-list", liodn_offs, sizeof(liodn_offs)); @@ -338,5 +338,22 @@ void fdt_fixup_liodn(void *blob) fdt_fixup_liodn_tbl(blob, rman_liodn_tbl, rman_liodn_tbl_sz); #endif - fdt_fixup_pci_liodn_offsets(blob, "fsl,qoriq-pcie-v2.4"); + ccsr_pcix_t *pcix = (ccsr_pcix_t *)CONFIG_SYS_PCIE1_ADDR; + int pci_ver = pcix->ipver1 & 0xffff, liodn_base = 0; + + if (pci_ver >= 0x0204) { + if (pci_ver >= 0x0300) + liodn_base = 1024; + else + liodn_base = 256; + } + + if (liodn_base) { + char compat[32]; + + sprintf(compat, "fsl,qoriq-pcie-v%d.%d", + (pci_ver & 0xff00) >> 8, pci_ver & 0xff); + fdt_fixup_pci_liodn_offsets(blob, compat, liodn_base); + fdt_fixup_pci_liodn_offsets(blob, "fsl,qoriq-pcie", liodn_base); + } } diff --git a/arch/powerpc/cpu/mpc85xx/t4240_ids.c b/arch/powerpc/cpu/mpc85xx/t4240_ids.c index 54c1cfd..f181315 100644 --- a/arch/powerpc/cpu/mpc85xx/t4240_ids.c +++ b/arch/powerpc/cpu/mpc85xx/t4240_ids.c @@ -86,10 +86,10 @@ struct liodn_id_table liodn_tbl[] = { SET_SATA_LIODN(1, 555), SET_SATA_LIODN(2, 556), - SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148), - SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228), - SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308), - SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308), + SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388), SET_DMA_LIODN(1, 147), SET_DMA_LIODN(2, 227), diff --git a/arch/powerpc/cpu/mpc8xxx/Makefile b/arch/powerpc/cpu/mpc8xxx/Makefile index 395fed1..1d083bf 100644 --- a/arch/powerpc/cpu/mpc8xxx/Makefile +++ b/arch/powerpc/cpu/mpc8xxx/Makefile @@ -31,3 +31,9 @@ obj-$(CONFIG_SYS_SRIO) += srio.o obj-$(CONFIG_FSL_LAW) += law.o endif + +ifdef CONFIG_SPL_BUILD +obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/ +else +obj-y += ddr/ +endif diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 4cc12ee..d4cd27d 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -674,7 +674,8 @@ #define CONFIG_NUM_DDR_CONTROLLERS 1 #endif -#elif defined(CONFIG_PPC_T1040) +#elif defined(CONFIG_PPC_T1040) || defined(CONFIG_PPC_T1042) ||\ +defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022) #define CONFIG_E5500 #define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ #define CONFIG_SYS_FSL_QORIQ_CHASSIS2 /* Freescale Chassis generation 2 */ diff --git a/arch/powerpc/include/asm/immap_83xx.h b/arch/powerpc/include/asm/immap_83xx.h index 3c86ff6..289f7ca 100644 --- a/arch/powerpc/include/asm/immap_83xx.h +++ b/arch/powerpc/include/asm/immap_83xx.h @@ -763,6 +763,7 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; +#ifndef CONFIG_MPC834x #ifdef CONFIG_HAS_FSL_MPH_USB #define CONFIG_SYS_MPC83xx_USB1_OFFSET 0x22000 /* use the MPH controller */ #define CONFIG_SYS_MPC83xx_USB2_OFFSET 0 @@ -770,6 +771,10 @@ typedef struct immap { #define CONFIG_SYS_MPC83xx_USB1_OFFSET 0 #define CONFIG_SYS_MPC83xx_USB2_OFFSET 0x23000 /* use the DR controller */ #endif +#else +#define CONFIG_SYS_MPC83xx_USB1_OFFSET 0x22000 +#define CONFIG_SYS_MPC83xx_USB2_OFFSET 0x23000 +#endif #elif defined(CONFIG_MPC8313) typedef struct immap { diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 060e0d7..6312618 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -282,7 +282,9 @@ typedef struct ccsr_pcix { u32 int_ack; /* PCIX IRQ Acknowledge */ u8 res000c[52]; u32 liodn_base; /* PCIX LIODN base register */ - u8 res0044[3004]; + u8 res0044[2996]; + u32 ipver1; /* PCIX IP block revision register 1 */ + u32 ipver2; /* PCIX IP block revision register 2 */ u32 potar0; /* PCIX Outbound Transaction Addr 0 */ u32 potear0; /* PCIX Outbound Translation Extended Addr 0 */ u32 powbar0; /* PCIX Outbound Window Base Addr 0 */ @@ -1847,7 +1849,8 @@ typedef struct ccsr_gur { #define FSL_CORENET2_RCWSR4_SRDS2_PRTCL 0x00ff0000 #define FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT 16 #define FSL_CORENET_RCWSR6_BOOT_LOC 0x0f800000 -#elif defined(CONFIG_PPC_T1040) +#elif defined(CONFIG_PPC_T1040) || defined(CONFIG_PPC_T1042) ||\ +defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022) #define FSL_CORENET2_RCWSR4_SRDS1_PRTCL 0xff000000 #define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 24 #define FSL_CORENET2_RCWSR4_SRDS2_PRTCL 0x00fe0000 diff --git a/board/LEOX/elpt860/u-boot.lds b/board/LEOX/elpt860/u-boot.lds index b30b667..c5e57ec 100644 --- a/board/LEOX/elpt860/u-boot.lds +++ b/board/LEOX/elpt860/u-boot.lds @@ -30,10 +30,10 @@ SECTIONS arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - common/libcommon.o (.text*) - arch/powerpc/cpu/mpc8xx/libmpc8xx.o (.text*) - board/LEOX/elpt860/libelpt860.o (.text*) - arch/powerpc/lib/libpowerpc.o (.text*) + common/built-in.o (.text*) + arch/powerpc/cpu/mpc8xx/built-in.o (.text*) + board/LEOX/elpt860/built-in.o (.text*) + arch/powerpc/lib/built-in.o (.text*) . = env_offset; common/env_embedded.o (.text*) diff --git a/board/LaCie/edminiv2/Makefile b/board/LaCie/edminiv2/Makefile index 7ca06f5..035f686 100644 --- a/board/LaCie/edminiv2/Makefile +++ b/board/LaCie/edminiv2/Makefile @@ -9,8 +9,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := edminiv2.o ../common/common.o diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile index 4fa08c5..f3074af 100644 --- a/board/LaCie/net2big_v2/Makefile +++ b/board/LaCie/net2big_v2/Makefile @@ -9,10 +9,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := net2big_v2.o ../common/common.o ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),) obj-y += ../common/cpld-gpio-bus.o diff --git a/board/LaCie/netspace_v2/Makefile b/board/LaCie/netspace_v2/Makefile index e5357e4..47778d8 100644 --- a/board/LaCie/netspace_v2/Makefile +++ b/board/LaCie/netspace_v2/Makefile @@ -9,8 +9,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := netspace_v2.o ../common/common.o diff --git a/board/LaCie/wireless_space/Makefile b/board/LaCie/wireless_space/Makefile index 11c535e..90a84f4 100644 --- a/board/LaCie/wireless_space/Makefile +++ b/board/LaCie/wireless_space/Makefile @@ -9,8 +9,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := wireless_space.o ../common/common.o diff --git a/board/Marvell/db64360/Makefile b/board/Marvell/db64360/Makefile index aad4776..aefe0a7 100644 --- a/board/Marvell/db64360/Makefile +++ b/board/Marvell/db64360/Makefile @@ -8,10 +8,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = db64360.o ../common/flash.o ../common/serial.o ../common/memory.o pci.o \ mv_eth.o ../common/ns16550.o mpsc.o ../common/i2c.o \ sdram_init.o ../common/intel_flash.o ../common/misc.o diff --git a/board/Marvell/db64460/Makefile b/board/Marvell/db64460/Makefile index ea9e570..a970f9a 100644 --- a/board/Marvell/db64460/Makefile +++ b/board/Marvell/db64460/Makefile @@ -8,10 +8,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y += db64460.o ../common/flash.o ../common/serial.o ../common/memory.o pci.o \ mv_eth.o ../common/ns16550.o mpsc.o ../common/i2c.o \ sdram_init.o ../common/intel_flash.o ../common/misc.o diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds index a656fa9..b0f09f5 100644 --- a/board/actux1/u-boot.lds +++ b/board/actux1/u-boot.lds @@ -16,10 +16,10 @@ SECTIONS .text : { *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) - net/libnet.o(.text*) - board/actux1/libactux1.o(.text*) - arch/arm/cpu/ixp/libixp.o(.text*) - drivers/input/libinput.o(.text*) + net/built-in.o(.text*) + board/actux1/built-in.o(.text*) + arch/arm/cpu/ixp/built-in.o(.text*) + drivers/input/built-in.o(.text*) . = env_offset; common/env_embedded.o(.ppcenv) diff --git a/board/actux2/u-boot.lds b/board/actux2/u-boot.lds index 7a17176..d84934e 100644 --- a/board/actux2/u-boot.lds +++ b/board/actux2/u-boot.lds @@ -16,10 +16,10 @@ SECTIONS .text : { *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) - net/libnet.o(.text*) - board/actux2/libactux2.o(.text*) - arch/arm/cpu/ixp/libixp.o(.text*) - drivers/input/libinput.o(.text*) + net/built-in.o(.text*) + board/actux2/built-in.o(.text*) + arch/arm/cpu/ixp/built-in.o(.text*) + drivers/input/built-in.o(.text*) . = env_offset; common/env_embedded.o(.ppcenv) diff --git a/board/actux3/u-boot.lds b/board/actux3/u-boot.lds index aadfdd2..30c204b 100644 --- a/board/actux3/u-boot.lds +++ b/board/actux3/u-boot.lds @@ -16,10 +16,10 @@ SECTIONS .text : { *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) - net/libnet.o(.text*) - board/actux3/libactux3.o(.text*) - arch/arm/cpu/ixp/libixp.o(.text*) - drivers/input/libinput.o(.text*) + net/built-in.o(.text*) + board/actux3/built-in.o(.text*) + arch/arm/cpu/ixp/built-in.o(.text*) + drivers/input/built-in.o(.text*) . = env_offset; common/env_embedded.o(.ppcenv) diff --git a/board/altera/nios2-generic/Makefile b/board/altera/nios2-generic/Makefile index 84c7bff..84690fe 100644 --- a/board/altera/nios2-generic/Makefile +++ b/board/altera/nios2-generic/Makefile @@ -6,10 +6,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := nios2-generic.o obj-$(CONFIG_CMD_IDE) += ../common/cfide.o obj-$(CONFIG_EPLED) += ../common/epled.o diff --git a/board/altera/nios2-generic/config.mk b/board/altera/nios2-generic/config.mk index f9f317c..a673525 100644 --- a/board/altera/nios2-generic/config.mk +++ b/board/altera/nios2-generic/config.mk @@ -5,11 +5,7 @@ # SPDX-License-Identifier: GPL-2.0+ # -# we get text_base from board config header, so do not use this -#CONFIG_SYS_TEXT_BASE = do-not-use-me - PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul -PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include ifeq ($(debug),1) PLATFORM_CPPFLAGS += -DDEBUG diff --git a/board/avionic-design/medcom-wide/Makefile b/board/avionic-design/medcom-wide/Makefile index 6c4ab64..87e1912 100644 --- a/board/avionic-design/medcom-wide/Makefile +++ b/board/avionic-design/medcom-wide/Makefile @@ -7,8 +7,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)../common $(obj)../../nvidia/common) - obj-y := ../common/tamonten.o include ../../nvidia/common/common.mk diff --git a/board/avionic-design/plutux/Makefile b/board/avionic-design/plutux/Makefile index 6c4ab64..87e1912 100644 --- a/board/avionic-design/plutux/Makefile +++ b/board/avionic-design/plutux/Makefile @@ -7,8 +7,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)../common $(obj)../../nvidia/common) - obj-y := ../common/tamonten.o include ../../nvidia/common/common.mk diff --git a/board/avionic-design/tec/Makefile b/board/avionic-design/tec/Makefile index 6c4ab64..87e1912 100644 --- a/board/avionic-design/tec/Makefile +++ b/board/avionic-design/tec/Makefile @@ -7,8 +7,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)../common $(obj)../../nvidia/common) - obj-y := ../common/tamonten.o include ../../nvidia/common/common.mk diff --git a/board/cogent/config.mk b/board/cogent/config.mk deleted file mode 100644 index 1452d46..0000000 --- a/board/cogent/config.mk +++ /dev/null @@ -1,12 +0,0 @@ -# -# (C) Copyright 2000 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -# -# Cogent Modular Architecture -# - -PLATFORM_CPPFLAGS += -I$(TOPDIR) diff --git a/board/cogent/dipsw.c b/board/cogent/dipsw.c index d2027c9..ecfbc25 100644 --- a/board/cogent/dipsw.c +++ b/board/cogent/dipsw.c @@ -1,5 +1,5 @@ #include <common.h> -#include <board/cogent/dipsw.h> +#include "dipsw.h" unsigned char dipsw_raw(void) diff --git a/board/cogent/flash.c b/board/cogent/flash.c index d4ae4d0..1da8f10 100644 --- a/board/cogent/flash.c +++ b/board/cogent/flash.c @@ -6,7 +6,7 @@ */ #include <common.h> -#include <board/cogent/flash.h> +#include "flash.h" #include <linux/compiler.h> flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ diff --git a/board/cogent/lcd.c b/board/cogent/lcd.c index 76f5ad1..8e90f98 100644 --- a/board/cogent/lcd.c +++ b/board/cogent/lcd.c @@ -48,7 +48,7 @@ #include <common.h> #include <stdarg.h> -#include <board/cogent/lcd.h> +#include "lcd.h" static char lines[2][LCD_LINE_LENGTH+1]; static int curline; diff --git a/board/cogent/mb.c b/board/cogent/mb.c index 603f123..3eea47d 100644 --- a/board/cogent/mb.c +++ b/board/cogent/mb.c @@ -6,11 +6,11 @@ */ #include <common.h> -#include <board/cogent/dipsw.h> -#include <board/cogent/lcd.h> -#include <board/cogent/rtc.h> -#include <board/cogent/par.h> -#include <board/cogent/pci.h> +#include "dipsw.h" +#include "lcd.h" +#include "rtc.h" +#include "par.h" +#include "pci.h" /* ------------------------------------------------------------------------- */ diff --git a/board/cogent/serial.c b/board/cogent/serial.c index 20631d1..f0d6b22 100644 --- a/board/cogent/serial.c +++ b/board/cogent/serial.c @@ -4,7 +4,7 @@ */ #include <common.h> -#include <board/cogent/serial.h> +#include "serial.h" #include <serial.h> #include <linux/compiler.h> diff --git a/board/compal/paz00/Makefile b/board/compal/paz00/Makefile index 824cd2e..b2d3b6b 100644 --- a/board/compal/paz00/Makefile +++ b/board/compal/paz00/Makefile @@ -14,8 +14,6 @@ # more details. # -$(shell mkdir -p $(obj)../../nvidia/common) - obj-y := paz00.o include ../../nvidia/common/common.mk diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c index 9f2937a..bc8e0ca 100644 --- a/board/compulab/cm_t35/cm_t35.c +++ b/board/compulab/cm_t35/cm_t35.c @@ -482,7 +482,7 @@ static void setup_net_chip_gmpc(void) &ctrl_base->gpmc_nadv_ale); } -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX /* * Routine: reset_net_chip * Description: reset the Ethernet controller via TPS65930 GPIO diff --git a/board/compulab/common/Makefile b/board/compulab/common/Makefile index 831be2e..6d7d068 100644 --- a/board/compulab/common/Makefile +++ b/board/compulab/common/Makefile @@ -6,5 +6,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o +obj-$(CONFIG_SYS_I2C_OMAP34XX) += eeprom.o obj-$(CONFIG_LCD) += omap3_display.o diff --git a/board/compulab/common/eeprom.h b/board/compulab/common/eeprom.h index cf8c302..e871629 100644 --- a/board/compulab/common/eeprom.h +++ b/board/compulab/common/eeprom.h @@ -10,7 +10,7 @@ #ifndef _EEPROM_ #define _EEPROM_ -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX int cl_eeprom_read_mac_addr(uchar *buf); u32 cl_eeprom_get_board_rev(void); #else diff --git a/board/compulab/trimslice/Makefile b/board/compulab/trimslice/Makefile index 0818673..f3bd00d 100644 --- a/board/compulab/trimslice/Makefile +++ b/board/compulab/trimslice/Makefile @@ -5,8 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)../../nvidia/common) - obj-y := trimslice.o include ../../nvidia/common/common.mk diff --git a/board/davinci/da8xxevm/u-boot-spl-hawk.lds b/board/davinci/da8xxevm/u-boot-spl-hawk.lds index e43130a..d49c314 100644 --- a/board/davinci/da8xxevm/u-boot-spl-hawk.lds +++ b/board/davinci/da8xxevm/u-boot-spl-hawk.lds @@ -19,8 +19,8 @@ SECTIONS .text : { arch/arm/cpu/arm926ejs/start.o (.text*) - arch/arm/cpu/arm926ejs/davinci/libdavinci.o (.text*) - drivers/mtd/nand/libnand.o (.text*) + arch/arm/cpu/arm926ejs/davinci/built-in.o (.text*) + drivers/mtd/nand/built-in.o (.text*) *(.text*) } diff --git a/board/dvlhost/u-boot.lds b/board/dvlhost/u-boot.lds index 40c9c80..0035a0b 100644 --- a/board/dvlhost/u-boot.lds +++ b/board/dvlhost/u-boot.lds @@ -16,10 +16,10 @@ SECTIONS .text : { *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) - net/libnet.o(.text*) - board/dvlhost/libdvlhost.o(.text*) - arch/arm/cpu/ixp/libixp.o(.text*) - drivers/serial/libserial.o(.text*) + net/built-in.o(.text*) + board/dvlhost/built-in.o(.text*) + arch/arm/cpu/ixp/built-in.o(.text*) + drivers/serial/built-in.o(.text*) . = env_offset; common/env_embedded.o(.ppcenv) diff --git a/board/emk/top5200/Makefile b/board/emk/top5200/Makefile index 0930d48..b455c26 100644 --- a/board/emk/top5200/Makefile +++ b/board/emk/top5200/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := top5200.o ../common/flash.o ../common/vpd.o ../common/am79c874.o diff --git a/board/emk/top860/Makefile b/board/emk/top860/Makefile index b2645f6..0401639 100644 --- a/board/emk/top860/Makefile +++ b/board/emk/top860/Makefile @@ -5,7 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif obj-y = top860.o ../common/flash.o ../common/vpd.o ../common/am79c874.o diff --git a/board/esd/adciop/Makefile b/board/esd/adciop/Makefile index a096e44..d0e264d 100644 --- a/board/esd/adciop/Makefile +++ b/board/esd/adciop/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = adciop.o flash.o ../common/misc.o ../common/pci.o diff --git a/board/esd/apc405/Makefile b/board/esd/apc405/Makefile index c6ab1a5..ada8bfd 100644 --- a/board/esd/apc405/Makefile +++ b/board/esd/apc405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = apc405.o \ ../common/misc.o \ ../common/auto_update.o diff --git a/board/esd/ar405/Makefile b/board/esd/ar405/Makefile index 2d16313..dd54f54 100644 --- a/board/esd/ar405/Makefile +++ b/board/esd/ar405/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = ar405.o flash.o ../common/misc.o diff --git a/board/esd/ash405/Makefile b/board/esd/ash405/Makefile index 4c866ee..aab8de4 100644 --- a/board/esd/ash405/Makefile +++ b/board/esd/ash405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = ash405.o flash.o \ ../common/misc.o \ ../common/esd405ep_nand.o \ diff --git a/board/esd/cms700/Makefile b/board/esd/cms700/Makefile index 8cfe3ba..2bf5006 100644 --- a/board/esd/cms700/Makefile +++ b/board/esd/cms700/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common/xilinx_jtag) -endif - # Objects for Xilinx JTAG programming (CPLD) CPLD = ../common/xilinx_jtag/lenval.o \ ../common/xilinx_jtag/micro.o \ diff --git a/board/esd/cpci2dp/Makefile b/board/esd/cpci2dp/Makefile index 1d15020..ce2c6dd 100644 --- a/board/esd/cpci2dp/Makefile +++ b/board/esd/cpci2dp/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = cpci2dp.o flash.o ../common/misc.o ../common/cmd_loadpci.o diff --git a/board/esd/cpci405/Makefile b/board/esd/cpci405/Makefile index 1af7e94..b140571 100644 --- a/board/esd/cpci405/Makefile +++ b/board/esd/cpci405/Makefile @@ -5,9 +5,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = cpci405.o flash.o ../common/misc.o ../common/auto_update.o obj-y += ../common/cmd_loadpci.o diff --git a/board/esd/cpci5200/Makefile b/board/esd/cpci5200/Makefile index fb6c0e2..8421f54 100644 --- a/board/esd/cpci5200/Makefile +++ b/board/esd/cpci5200/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -# ifneq ($(OBJTREE),$(SRCTREE)) -# $(shell mkdir -p $(obj)../common/xilinx_jtag) -# endif - # Objects for Xilinx JTAG programming (CPLD) # CPLD = ../common/xilinx_jtag/lenval.o \ # ../common/xilinx_jtag/micro.o \ diff --git a/board/esd/cpci750/Makefile b/board/esd/cpci750/Makefile index 8b3dc33..a3300c9 100644 --- a/board/esd/cpci750/Makefile +++ b/board/esd/cpci750/Makefile @@ -8,10 +8,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../../Marvell/common) -endif - obj-y = misc.o obj-y += cpci750.o serial.o ../../Marvell/common/memory.o pci.o \ mv_eth.o mpsc.o i2c.o \ diff --git a/board/esd/cpciiser4/Makefile b/board/esd/cpciiser4/Makefile index 4d3c34a..b8d6bea 100644 --- a/board/esd/cpciiser4/Makefile +++ b/board/esd/cpciiser4/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = cpciiser4.o flash.o ../common/misc.o diff --git a/board/esd/dasa_sim/Makefile b/board/esd/dasa_sim/Makefile index f0a5a8f..eb9f5f8 100644 --- a/board/esd/dasa_sim/Makefile +++ b/board/esd/dasa_sim/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = dasa_sim.o flash.o cmd_dasa_sim.o eeprom.o ../common/pci.o diff --git a/board/esd/dp405/Makefile b/board/esd/dp405/Makefile index 6809c67..cfcfb66 100644 --- a/board/esd/dp405/Makefile +++ b/board/esd/dp405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common/xilinx_jtag) -endif - # Objects for Xilinx JTAG programming (CPLD) CPLD = ../common/xilinx_jtag/lenval.o \ ../common/xilinx_jtag/micro.o \ diff --git a/board/esd/du405/Makefile b/board/esd/du405/Makefile index 12ce41a..7914eab 100644 --- a/board/esd/du405/Makefile +++ b/board/esd/du405/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = du405.o flash.o ../common/misc.o diff --git a/board/esd/hh405/Makefile b/board/esd/hh405/Makefile index 0507f1b..fba21a3 100644 --- a/board/esd/hh405/Makefile +++ b/board/esd/hh405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = hh405.o flash.o \ ../common/misc.o \ ../common/esd405ep_nand.o \ diff --git a/board/esd/hub405/Makefile b/board/esd/hub405/Makefile index 5447a95..99e18b5 100644 --- a/board/esd/hub405/Makefile +++ b/board/esd/hub405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = hub405.o flash.o \ ../common/misc.o \ ../common/esd405ep_nand.o \ diff --git a/board/esd/ocrtc/Makefile b/board/esd/ocrtc/Makefile index 0d9a6fd..44b7d5d 100644 --- a/board/esd/ocrtc/Makefile +++ b/board/esd/ocrtc/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = ocrtc.o flash.o ../common/misc.o cmd_ocrtc.o diff --git a/board/esd/pci405/Makefile b/board/esd/pci405/Makefile index 2f8706b..9e659c7 100644 --- a/board/esd/pci405/Makefile +++ b/board/esd/pci405/Makefile @@ -5,9 +5,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = pci405.o flash.o ../common/misc.o cmd_pci405.o obj-y += writeibm.o diff --git a/board/esd/pf5200/Makefile b/board/esd/pf5200/Makefile index a9d20c9..a54289c 100644 --- a/board/esd/pf5200/Makefile +++ b/board/esd/pf5200/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -# ifneq ($(OBJTREE),$(SRCTREE)) -# $(shell mkdir -p $(obj)../common/xilinx_jtag) -# endif - # Objects for Xilinx JTAG programming (CPLD) # CPLD = ../common/xilinx_jtag/lenval.o \ # ../common/xilinx_jtag/micro.o \ diff --git a/board/esd/plu405/Makefile b/board/esd/plu405/Makefile index 45b962f..6ffae67 100644 --- a/board/esd/plu405/Makefile +++ b/board/esd/plu405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = plu405.o flash.o \ ../common/misc.o \ ../common/esd405ep_nand.o \ diff --git a/board/esd/pmc405/Makefile b/board/esd/pmc405/Makefile index f4aa1c9..ad98207 100644 --- a/board/esd/pmc405/Makefile +++ b/board/esd/pmc405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common/xilinx_jtag) -endif - # Objects for Xilinx JTAG programming (CPLD) CPLD = ../common/xilinx_jtag/lenval.o \ ../common/xilinx_jtag/micro.o \ diff --git a/board/esd/pmc405de/Makefile b/board/esd/pmc405de/Makefile index 7d5b273..b3f6dcd 100644 --- a/board/esd/pmc405de/Makefile +++ b/board/esd/pmc405de/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = pmc405de.o obj-$(CONFIG_CMD_CHIP_CONFIG) += chip_config.o obj-y += ../common/cmd_loadpci.o diff --git a/board/esd/pmc440/Makefile b/board/esd/pmc440/Makefile index b1318c7..708e9d1 100644 --- a/board/esd/pmc440/Makefile +++ b/board/esd/pmc440/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = pmc440.o cmd_pmc440.o sdram.o fpga.o \ ../common/cmd_loadpci.o extra-y += init.o diff --git a/board/esd/voh405/Makefile b/board/esd/voh405/Makefile index 8fcfa37..3d82399 100644 --- a/board/esd/voh405/Makefile +++ b/board/esd/voh405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = voh405.o flash.o \ ../common/misc.o \ ../common/esd405ep_nand.o \ diff --git a/board/esd/vom405/Makefile b/board/esd/vom405/Makefile index c8a4a4e..7cf5c02 100644 --- a/board/esd/vom405/Makefile +++ b/board/esd/vom405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common/xilinx_jtag) -endif - # Objects for Xilinx JTAG programming (CPLD) CPLD = ../common/xilinx_jtag/lenval.o \ ../common/xilinx_jtag/micro.o \ diff --git a/board/esd/wuh405/Makefile b/board/esd/wuh405/Makefile index 046ebad..b9beeff 100644 --- a/board/esd/wuh405/Makefile +++ b/board/esd/wuh405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = wuh405.o flash.o \ ../common/misc.o \ ../common/esd405ep_nand.o \ diff --git a/board/esteem192e/u-boot.lds b/board/esteem192e/u-boot.lds index 87642d6..59a86bf 100644 --- a/board/esteem192e/u-boot.lds +++ b/board/esteem192e/u-boot.lds @@ -18,8 +18,8 @@ SECTIONS arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - net/libnet.o (.text*) - board/esteem192e/libesteem192e.o (.text*) + net/built-in.o (.text*) + board/esteem192e/built-in.o (.text*) . = env_offset; common/env_embedded.o (.text*) diff --git a/board/freescale/m52277evb/config.mk b/board/freescale/m52277evb/config.mk deleted file mode 100644 index 0ffb0a2..0000000 --- a/board/freescale/m52277evb/config.mk +++ /dev/null @@ -1,11 +0,0 @@ -# -# (C) Copyright 2000-2003 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# Coldfire contribution by Bernhard Kuhn <bkuhn@metrowerks.com> -# -# SPDX-License-Identifier: GPL-2.0+ -# - -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) diff --git a/board/freescale/m52277evb/u-boot.lds b/board/freescale/m52277evb/u-boot.lds index f3337a3..70121d9 100644 --- a/board/freescale/m52277evb/u-boot.lds +++ b/board/freescale/m52277evb/u-boot.lds @@ -13,8 +13,8 @@ SECTIONS .text : { arch/m68k/cpu/mcf5227x/start.o (.text*) - arch/m68k/cpu/mcf5227x/libmcf5227x.o (.text*) - arch/m68k/lib/libm68k.o (.text*) + arch/m68k/cpu/mcf5227x/built-in.o (.text*) + arch/m68k/lib/built-in.o (.text*) *(.text*) } diff --git a/board/freescale/m5235evb/config.mk b/board/freescale/m5235evb/config.mk deleted file mode 100644 index 9ab4582..0000000 --- a/board/freescale/m5235evb/config.mk +++ /dev/null @@ -1,12 +0,0 @@ -# -# (C) Copyright 2000-2003 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# Coldfire contribution by Bernhard Kuhn <bkuhn@metrowerks.com> -# -# SPDX-License-Identifier: GPL-2.0+ -# - -/*CONFIG_SYS_TEXT_BASE = 0xFFC00000*/ -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) diff --git a/board/freescale/m53017evb/u-boot.lds b/board/freescale/m53017evb/u-boot.lds index ef21299..de8d09b 100644 --- a/board/freescale/m53017evb/u-boot.lds +++ b/board/freescale/m53017evb/u-boot.lds @@ -12,9 +12,9 @@ SECTIONS /* Read-only sections, merged into text segment: */ .text : { - arch/m68k/cpu/mcf532x/start.o (.text*) - arch/m68k/cpu/mcf532x/libmcf532x.o (.text*) - arch/m68k/lib/libm68k.o (.text*) + arch/m68k/cpu/mcf532x/start.o (.text*) + arch/m68k/cpu/mcf532x/built-in.o (.text*) + arch/m68k/lib/built-in.o (.text*) . = DEFINED(env_offset) ? env_offset : .; common/env_embedded.o (.text*) diff --git a/board/freescale/m54451evb/config.mk b/board/freescale/m54451evb/config.mk deleted file mode 100644 index 0ffb0a2..0000000 --- a/board/freescale/m54451evb/config.mk +++ /dev/null @@ -1,11 +0,0 @@ -# -# (C) Copyright 2000-2003 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# Coldfire contribution by Bernhard Kuhn <bkuhn@metrowerks.com> -# -# SPDX-License-Identifier: GPL-2.0+ -# - -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) diff --git a/board/freescale/m54455evb/config.mk b/board/freescale/m54455evb/config.mk deleted file mode 100644 index 0ffb0a2..0000000 --- a/board/freescale/m54455evb/config.mk +++ /dev/null @@ -1,11 +0,0 @@ -# -# (C) Copyright 2000-2003 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# Coldfire contribution by Bernhard Kuhn <bkuhn@metrowerks.com> -# -# SPDX-License-Identifier: GPL-2.0+ -# - -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds index 3acc4ca..8d5cc91 100644 --- a/board/freescale/mx31ads/u-boot.lds +++ b/board/freescale/mx31ads/u-boot.lds @@ -22,11 +22,11 @@ SECTIONS /* WARNING - the following is hand-optimized to fit within */ /* the sector layout of our flash chips! XXX FIXME XXX */ - arch/arm/cpu/arm1136/start.o (.text*) - board/freescale/mx31ads/libmx31ads.o (.text*) - arch/arm/lib/libarm.o (.text*) - net/libnet.o (.text*) - drivers/mtd/libmtd.o (.text*) + arch/arm/cpu/arm1136/start.o (.text*) + board/freescale/mx31ads/built-in.o (.text*) + arch/arm/lib/built-in.o (.text*) + net/built-in.o (.text*) + drivers/mtd/built-in.o (.text*) . = DEFINED(env_offset) ? env_offset : .; common/env_embedded.o(.text*) diff --git a/board/freescale/p1010rdb/README b/board/freescale/p1010rdb/README.P1010RDB-PA index 7f18aaa..158a1b3 100644 --- a/board/freescale/p1010rdb/README +++ b/board/freescale/p1010rdb/README.P1010RDB-PA @@ -204,5 +204,5 @@ Place uImage, p1010rdb.dtb and rootfs files in the TFTP disk area. => bootm 1000000 3000000 2000000 -Please contact your local field applications engineer or sales representative -to obtain related documents, such as P1010-RDB User Guide for details. +For more details, please refer to P1010RDB User Guide and access website +www.freescale.com diff --git a/board/freescale/p1010rdb/README.P1010RDB-PB b/board/freescale/p1010rdb/README.P1010RDB-PB new file mode 100644 index 0000000..cf459b3 --- /dev/null +++ b/board/freescale/p1010rdb/README.P1010RDB-PB @@ -0,0 +1,188 @@ +Overview +========= +The P1010RDB-PB is a Freescale Reference Design Board that hosts the P1010 SoC. +P1010RDB-PB is a variation of previous P1010RDB-PA board. + +The P1010 is a cost-effective, low-power, highly integrated host processor +based on a Power Architecture e500v2 core (maximum core frequency 1GHz),that +addresses the requirements of several routing, gateways, storage, consumer, +and industrial applications. Applications of interest include the main CPUs and +I/O processors in network attached storage (NAS), the voice over IP (VoIP) +router/gateway, and wireless LAN (WLAN) and industrial controllers. + +The P1010RDB-PB board features are as following: +Memory subsystem: + - 1G bytes unbuffered DDR3 SDRAM discrete devices (32-bit bus) + - 32M bytes NOR flash single-chip memory + - 2G bytes NAND flash memory + - 16M bytes SPI memory + - 256K bit M24256 I2C EEPROM + - I2C Board EEPROM 128x8 bit memory + - SD/MMC connector to interface with the SD memory card +Interfaces: + - Three 10/100/1000 BaseT Ethernet ports (One RGMII and two SGMII) + - PCIe 2.0: two x1 mini-PCIe slots + - SATA 2.0: two SATA interfaces + - USB 2.0: one USB interface + - FlexCAN: two FlexCAN interfaces (revision 2.0B) + - UART: one USB-to-Serial interface + - TDM: 2 FXS ports connected via an external SLIC to the TDM interface. + 1 FXO port connected via a relay to FXS for switchover to POTS + +Board connectors: + - Mini-ITX power supply connector + - JTAG/COP for debugging + +POR: support critical POR setting changed via switch on board +PCB: 6-layer routing (4-layer signals, 2-layer power and ground) + +Physical Memory Map on P1010RDB +=============================== +Address Start Address End Memory type Attributes +0x0000_0000 0x3fff_ffff DDR 1G Cacheable +0xa000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable +0xee00_0000 0xefff_ffff NOR Flash 32M non-cacheable +0xffc2_0000 0xffc5_ffff PCI IO range 256K non-cacheable +0xffa0_0000 0xffaf_ffff NAND Flash 1M cacheable +0xffb0_0000 0xffbf_ffff Board CPLD 1M non-cacheable +0xffd0_0000 0xffd0_3fff L1 for Stack 16K Cacheable TLB0 +0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + + +Serial Port Configuration on P1010RDB +===================================== +Configure the serial port of the attached computer with the following values: + -Data rate: 115200 bps + -Number of data bits: 8 + -Parity: None + -Number of Stop bits: 1 + -Flow Control: Hardware/None + + +P1010RDB-PB default DIP-switch settings +======================================= +SW1[1:8]= 10101010 +SW2[1:8]= 11011000 +SW3[1:8]= 10010000 +SW4[1:4]= 1010 +SW5[1:8]= 11111010 + + +P1010RDB-PB boot mode settings via DIP-switch +============================================= +SW4[1:4]= 1111 and SW3[3:4]= 00 for 16bit NOR boot +SW4[1:4]= 1010 and SW3[3:4]= 01 for 8bit NAND boot +SW4[1:4]= 0110 and SW3[3:4]= 00 for SPI boot +SW4[1:4]= 0111 and SW3[3:4]= 10 for SD boot +Note: 1 stands for 'on', 0 stands for 'off' + + +Switch P1010RDB-PB boot mode via software without setting DIP-switch +==================================================================== +=> run boot_bank0 (boot from NOR bank0) +=> run boot_bank1 (boot from NOR bank1) +=> run boot_nand (boot from NAND flash) +=> run boot_spi (boot from SPI flash) +=> run boot_sd (boot from SD card) + + +Frequency combination support on P1010RDB-PB +============================================= +SW1[4:7] SW5[1] SW5[5:8] SW2[2] Core(MHz) Platform(MHz) DDR(MT/s) +0101 1 1010 0 800 400 800 +1001 1 1010 0 800 400 667 +1010 1 1100 0 667 333 667 +1000 0 1010 0 533 266 667 +0101 1 1010 1 1000 400 800 +1001 1 1010 1 1000 400 667 + + +Setting of pin mux +================== +Since pins multiplexing, TDM and CAN are muxed with SPI flash. +SDHC is muxed with IFC. IFC and SPI flash are enabled by default. + +To enable TDM: +=> setenv hwconfig fsl_p1010mux:tdm_can=tdm +=> save;reset + +To enable FlexCAN: +=> setenv hwconfig fsl_p1010mux:tdm_can=can +=> save;reset + +To enable SDHC in case of NOR/NAND/SPI boot + a) For temporary use case in runtime without reboot system + run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC. + + b) For long-term use case + set 'esdhc' in hwconfig and save it. + +To enable IFC in case of SD boot + a) For temporary use case in runtime without reboot system + run 'mux ifc' in u-boot to validate IFC with invalidating SDHC. + + b) For long-term use case + set 'ifc' in hwconfig and save it. + + +Build images for different boot mode +==================================== +First setup cross compile environment on build host + $ export ARCH=powerpc + $ export CROSS_COMPILE=<your-compiler-path>/powerpc-linux-gnu- + +1. For NOR boot + $ make P1010RDB-PB_NOR + +2. For NAND boot + $ make P1010RDB-PB_NAND + +3. For SPI boot + $ make P1010RDB-PB_SPIFLASH + +4. For SD boot + $ make P1010RDB-PB_SDCARD + + +Steps to program images to flash for different boot mode +======================================================== +1. NOR boot + => tftp 1000000 u-boot.bin + For bank0 + => pro off all;era eff80000 efffffff;cp.b 1000000 eff80000 $filesize + set SW1[8]=0, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board + + For bank1 + => pro off all;era eef80000 eeffffff;cp.b 1000000 eef80000 $filesize + set SW1[8]=1, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board + +2. NAND boot + => tftp 1000000 u-boot-nand.bin + => nand erase 0 $filesize; nand write $loadaddr 0 $filesize + Set SW4[1:4]= 1010 and SW3[3:4]= 01, then power on the board + +3. SPI boot + 1) cat p1010rdb-config-header.bin u-boot.bin > u-boot-spi-combined.bin + 2) => tftp 1000000 u-boot-spi-combined.bin + 3) => sf probe 0; sf erase 0 100000; sf write 1000000 0 100000 + set SW4[1:4]= 0110 and SW3[3:4]= 00, then power on the board + +4. SD boot + 1) cat p1010rdb-config-header.bin u-boot.bin > u-boot-sd-combined.bin + 2) => tftp 1000000 u-boot-sd-combined.bin + 3) => mux sdhc + 4) => mmc write 1000000 0 1050 + set SW4[1:4]= 0111 and SW3[3:4]= 10, then power on the board + + +Boot Linux from network using TFTP on P1010RDB-PB +================================================= +Place uImage, p1010rdb.dtb and rootfs files in the TFTP download path. + => tftp 1000000 uImage + => tftp 2000000 p1010rdb.dtb + => tftp 3000000 rootfs.ext2.gz.uboot.p1010rdb + => bootm 1000000 3000000 2000000 + + +For more details, please refer to P1010RDB-PB User Guide and access website +www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t1040qds/Makefile b/board/freescale/t1040qds/Makefile index a2dba6f..93af9eb 100644 --- a/board/freescale/t1040qds/Makefile +++ b/board/freescale/t1040qds/Makefile @@ -4,7 +4,7 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-y += $(BOARD).o +obj-y += t1040qds.o obj-y += ddr.o obj-$(CONFIG_PCI) += pci.o obj-y += law.o diff --git a/board/freescale/t1040qds/t1040_pbi.cfg b/board/freescale/t1040qds/t1040_pbi.cfg new file mode 100644 index 0000000..624398a --- /dev/null +++ b/board/freescale/t1040qds/t1040_pbi.cfg @@ -0,0 +1,27 @@ +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#Configure CPC1 as 512KB SRAM +09010100 00000000 +09010104 fffc0007 +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000cf0 00000000 +09000cf4 fffc0000 +09000cf8 81000011 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Configure SPI controller +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/freescale/t1040qds/t1040_rcw.cfg b/board/freescale/t1040qds/t1040_rcw.cfg new file mode 100644 index 0000000..0d0dfa5 --- /dev/null +++ b/board/freescale/t1040qds/t1040_rcw.cfg @@ -0,0 +1,7 @@ +#PBL preamble and RCW header +aa55aa55 010e0100 +# serdes protocol 0x66 +0a10000c 0c000000 00000000 00000000 +66000002 00000000 fc027000 01000000 +00000000 00000000 00000000 00030810 +00000000 03fc500f 00000000 00000000 diff --git a/board/freescale/t104xrdb/Makefile b/board/freescale/t104xrdb/Makefile new file mode 100644 index 0000000..76c0c94 --- /dev/null +++ b/board/freescale/t104xrdb/Makefile @@ -0,0 +1,12 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + + +obj-y += t104xrdb.o +obj-y += ddr.o +obj-$(CONFIG_PCI) += pci.o +obj-y += law.o +obj-y += tlb.o diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README new file mode 100644 index 0000000..2cd8219 --- /dev/null +++ b/board/freescale/t104xrdb/README @@ -0,0 +1,200 @@ +Overview +-------- +The T1040RDB is a Freescale reference board that hosts the T1040 SoC +(and variants). Variants inclued T1042 presonality of T1040, in which +case T1040RDB can also be called T1042RDB. + +The T1042RDB_PI is a Freescale reference board that hosts the T1042 SoC. +(a personality of T1040 SoC). The board is similar to T1040RDB but is +designed specially with low power features targeted for Printing Image Market. + +T1040 SoC Overview +------------------ +The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA +processor cores with high-performance data path acceleration architecture +and network peripheral interfaces required for networking & telecommunications. + +The T1040/T1042 SoC includes the following function and features: + + - Four e5500 cores, each with a private 256 KB L2 cache + - 256 KB shared L3 CoreNet platform cache (CPC) + - Interconnect CoreNet platform + - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving + support + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + for the following functions: + - Packet parsing, classification, and distribution + - Queue management for scheduling, packet sequencing, and congestion + management + - Cryptography Acceleration (SEC 5.0) + - RegEx Pattern Matching Acceleration (PME 2.2) + - IEEE Std 1588 support + - Hardware buffer management for buffer allocation and deallocation + - Ethernet interfaces + - Integrated 8-port Gigabit Ethernet switch (T1040 only) + - Four 1 Gbps Ethernet controllers + - Two RGMII interfaces or one RGMII and one MII interfaces + - High speed peripheral interfaces + - Four PCI Express 2.0 controllers running at up to 5 GHz + - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation + - Upto two QSGMII interface + - Upto six SGMII interface supporting 1000 Mbps + - One SGMII interface supporting upto 2500 Mbps + - Additional peripheral interfaces + - Two USB 2.0 controllers with integrated PHY + - SD/eSDHC/eMMC + - eSPI controller + - Four I2C controllers + - Four UARTs + - Four GPIO controllers + - Integrated flash controller (IFC) + - LCD and HDMI interface (DIU) with 12 bit dual data rate + - TDM interface + - Multicore programmable interrupt controller (PIC) + - Two 8-channel DMA engines + - Single source clocking implementation + - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) + +T1040 SoC Personalities +------------------------- + +T1022 Personality: +T1022 is a reduced personality of T1040 with less core/clusters. + +T1042 Personality: +T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit +Ethernet switch. Rest of the blocks are same as T1040 + + +T1040RDB board Overview +------------------------- + - SERDES Connections, 8 lanes information: + 1: None + 2: SGMII + 3: QSGMII + 4: QSGMII + 5: PCIe1 x1 slot + 6: mini PCIe connector + 7: mini PCIe connector + 8: SATA connector + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + - IFC/Local Bus + - NAND flash: 1GB 8-bit NAND flash + - NOR: 128MB 16-bit NOR Flash + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - CPLD + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Power Supplies + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - SDHC/SDXC connector + - SPI + - On-board 64MB SPI flash + - Other IO + - Two Serial ports + - Four I2C ports + +T1042RDB_PI board Overview +------------------------- + - SERDES Connections, 8 lanes information: + 1, 2, 3, 4 : PCIe x4 slot + 5: mini PCIe connector + 6: mini PCIe connector + 7: NA + 8: SATA connector + - DDR Controller + - Supports rates of up to 1600 MHz data-rate + - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. + - IFC/Local Bus + - NAND flash: 1GB 8-bit NAND flash + - NOR: 128MB 16-bit NOR Flash + - Ethernet + - Two on-board RGMII 10/100/1G ethernet ports. + - CPLD + - Clocks + - System and DDR clock (SYSCLK, “DDRCLK”) + - SERDES clocks + - Video + - DIU supports video at up to 1280x1024x32bpp + - Power Supplies + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - SDHC/SDXC connector + - SPI + - On-board 64MB SPI flash + - Other IO + - Two Serial ports + - Four I2C ports + +Memory map +----------- +The addresses in brackets are physical addresses. + +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB +0x0_0000_0000 0x0_ffff_ffff DDR 2GB + + +NOR Flash memory Map +--------------------- + Start End Definition Size +0xEFF80000 0xEFFFFFFF u-boot (current bank) 512KB +0xEFF60000 0xEFF7FFFF u-boot env (current bank) 128KB +0xEFF40000 0xEFF5FFFF FMAN Ucode (current bank) 128KB +0xED300000 0xEFF3FFFF rootfs (alt bank) 44MB + 256KB +0xEC800000 0xEC8FFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF80000 0xEBFFFFFF u-boot (alt bank) 512KB +0xEBF60000 0xEBF7FFFF u-boot env (alt bank) 128KB +0xEBF40000 0xEBF5FFFF FMAN ucode (alt bank) 128KB +0xE9300000 0xEBF3FFFF rootfs (current bank) 44MB + 256KB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +Various Software configurations/environment variables/commands +-------------------------------------------------------------- +The below commands apply to the board + +1. U-boot environment variable hwconfig + The default hwconfig is: + hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1: + dr_mode=host,phy_type=utmi + Note: For USB gadget set "dr_mode=peripheral" + +2. FMAN Ucode versions + fsl_fman_ucode_t1040.bin + +3. Switching to alternate bank + Commands for switching to alternate bank. + + 1. To change from vbank0 to vbank4 + => qixis_reset altbank (it will boot using vbank4) + + 2.To change from vbank4 to vbank0 + => qixis reset (it will boot using vbank0) diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c new file mode 100644 index 0000000..8f58dd6 --- /dev/null +++ b/board/freescale/t104xrdb/ddr.c @@ -0,0 +1,132 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <hwconfig.h> +#include <asm/mmu.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> +#include <asm/fsl_law.h> +#include "ddr.h" + +DECLARE_GLOBAL_DATA_PTR; + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "RAW timing DDR"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->cpo_override = pbsp->cpo; + popts->write_data_delay = + pbsp->write_data_delay; + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp->force_2t; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found\n"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->cpo_override = pbsp_highest->cpo; + popts->write_data_delay = pbsp_highest->write_data_delay; + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twot_en = pbsp_highest->force_2t; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" + "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " + "wrlvl_ctrl_3 0x%x\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, + pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * rtt and rtt_wr override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/t104xrdb/ddr.h b/board/freescale/t104xrdb/ddr.h new file mode 100644 index 0000000..9276b59 --- /dev/null +++ b/board/freescale/t104xrdb/ddr.h @@ -0,0 +1,76 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DDR_H__ +#define __DDR_H__ + +dimm_params_t ddr_raw_timing = { + .n_ranks = 2, + .rank_density = 2147483648u, + .capacity = 4294967296u, + .primary_sdram_width = 64, + .ec_sdram_width = 8, + .registered_dimm = 0, + .mirrored_dimm = 1, + .n_row_addr = 15, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 2, /* ECC */ + .burst_lengths_bitmask = 0x0c, + + .tckmin_x_ps = 1071, + .caslat_x = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */ + .taa_ps = 13910, + .twr_ps = 15000, + .trcd_ps = 13910, + .trrd_ps = 6000, + .trp_ps = 13910, + .tras_ps = 34000, + .trc_ps = 48910, + .trfc_ps = 260000, + .twtr_ps = 7500, + .trtp_ps = 7500, + .refresh_rate_ps = 7800000, + .tfaw_ps = 35000, +}; + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; + u32 cpo; + u32 write_data_delay; + u32 force_2t; +}; + +/* + * These tables contain all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ + +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | + */ + {2, 1066, 4, 8, 4, 0x05070609, 0x08090a08, 0xff, 2, 0}, + {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, + {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, + {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; +#endif diff --git a/board/freescale/t104xrdb/law.c b/board/freescale/t104xrdb/law.c new file mode 100644 index 0000000..2362d43 --- /dev/null +++ b/board/freescale/t104xrdb/law.c @@ -0,0 +1,32 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_SYS_NO_FLASH + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_CPLD_BASE_PHYS + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t104xrdb/pci.c b/board/freescale/t104xrdb/pci.c new file mode 100644 index 0000000..c53e3b7 --- /dev/null +++ b/board/freescale/t104xrdb/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/fsl_pci.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <asm/fsl_serdes.h> + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c new file mode 100644 index 0000000..6e29d64 --- /dev/null +++ b/board/freescale/t104xrdb/t104xrdb.c @@ -0,0 +1,93 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> + +#include "t104xrdb.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + struct cpu_type *cpu = gd->arch.cpu; + + printf("Board: %sRDB\n", cpu->name); + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_SYS_FLASH_BASE + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); +#endif + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + return 0; +} + +int misc_init_r(void) +{ + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); +#endif +} diff --git a/board/freescale/t104xrdb/t104xrdb.h b/board/freescale/t104xrdb/t104xrdb.h new file mode 100644 index 0000000..e7cc0c7 --- /dev/null +++ b/board/freescale/t104xrdb/t104xrdb.h @@ -0,0 +1,13 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __T104x_RDB_H__ +#define __T104x_RDB_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t104xrdb/tlb.c b/board/freescale/t104xrdb/tlb.c new file mode 100644 index 0000000..84f97a4 --- /dev/null +++ b/board/freescale/t104xrdb/tlb.c @@ -0,0 +1,107 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the + * SRAM is at 0xfffc0000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256K, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 5, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 9, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef CONFIG_SYS_CPLD_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_256K, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/gaisler/gr_cpci_ax2000/config.mk b/board/gaisler/gr_cpci_ax2000/config.mk index e9c6028..309c879 100644 --- a/board/gaisler/gr_cpci_ax2000/config.mk +++ b/board/gaisler/gr_cpci_ax2000/config.mk @@ -18,5 +18,4 @@ CONFIG_SYS_TEXT_BASE = 0x00000000 # U-BOOT IN SDRAM #CONFIG_SYS_TEXT_BASE = 0x60000000 -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) \ - -I$(TOPDIR)/board +PLATFORM_CPPFLAGS += -I$(TOPDIR)/board diff --git a/board/gaisler/gr_ep2s60/config.mk b/board/gaisler/gr_ep2s60/config.mk index 6c31a17..d57efae 100644 --- a/board/gaisler/gr_ep2s60/config.mk +++ b/board/gaisler/gr_ep2s60/config.mk @@ -16,5 +16,4 @@ CONFIG_SYS_TEXT_BASE = 0x00000000 # U-BOOT IN SDRAM #CONFIG_SYS_TEXT_BASE = 0x40000000 -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) \ - -I$(TOPDIR)/board +PLATFORM_CPPFLAGS += -I$(TOPDIR)/board diff --git a/board/gaisler/gr_xc3s_1500/config.mk b/board/gaisler/gr_xc3s_1500/config.mk index 3b59cca..e87320b 100644 --- a/board/gaisler/gr_xc3s_1500/config.mk +++ b/board/gaisler/gr_xc3s_1500/config.mk @@ -15,5 +15,4 @@ CONFIG_SYS_TEXT_BASE = 0x00000000 # U-BOOT IN RAM #CONFIG_SYS_TEXT_BASE = 0x40000000 -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) \ - -I$(TOPDIR)/board +PLATFORM_CPPFLAGS += -I$(TOPDIR)/board diff --git a/board/gaisler/grsim/config.mk b/board/gaisler/grsim/config.mk index d98ed54..df26f82 100644 --- a/board/gaisler/grsim/config.mk +++ b/board/gaisler/grsim/config.mk @@ -15,5 +15,4 @@ CONFIG_SYS_TEXT_BASE = 0x00000000 # U-BOOT IN RAM #CONFIG_SYS_TEXT_BASE = 0x40000000 -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) \ - -I$(TOPDIR)/board +PLATFORM_CPPFLAGS += -I$(TOPDIR)/board diff --git a/board/gaisler/grsim_leon2/config.mk b/board/gaisler/grsim_leon2/config.mk index 59e4e31..99f9a68 100644 --- a/board/gaisler/grsim_leon2/config.mk +++ b/board/gaisler/grsim_leon2/config.mk @@ -15,5 +15,4 @@ CONFIG_SYS_TEXT_BASE = 0x00000000 # RUN U-BOOT FROM RAM #CONFIG_SYS_TEXT_BASE = 0x40000000 -PLATFORM_CPPFLAGS += -DCONFIG_SYS_TEXT_BASE=$(CONFIG_SYS_TEXT_BASE) \ - -I$(TOPDIR)/board +PLATFORM_CPPFLAGS += -I$(TOPDIR)/board diff --git a/board/genietv/u-boot.lds b/board/genietv/u-boot.lds index e217f06..70ab702 100644 --- a/board/genietv/u-boot.lds +++ b/board/genietv/u-boot.lds @@ -18,11 +18,11 @@ SECTIONS arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - lib/libgeneric.o (.text*) - net/libnet.o (.text*) - arch/powerpc/cpu/mpc8xx/libmpc8xx.o (.text*) - board/genietv/libgenietv.o (.text*) - arch/powerpc/lib/libpowerpc.o (.text*) + lib/built-in.o (.text*) + net/built-in.o (.text*) + arch/powerpc/cpu/mpc8xx/built-in.o (.text*) + board/genietv/built-in.o (.text*) + arch/powerpc/lib/built-in.o (.text*) *(.text.do_load_serial*) *(.text.do_mem_*) *(.text.do_bootm*) diff --git a/board/hermes/u-boot.lds b/board/hermes/u-boot.lds index 9419f83..0309860 100644 --- a/board/hermes/u-boot.lds +++ b/board/hermes/u-boot.lds @@ -17,7 +17,7 @@ SECTIONS /* the sector layout of our flash chips! XXX FIXME XXX */ arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - board/hermes/libhermes.o (.text*) + board/hermes/built-in.o (.text*) . = env_offset; common/env_embedded.o (.text*) diff --git a/board/keymile/km82xx/Makefile b/board/keymile/km82xx/Makefile index b44582f..20f193a 100644 --- a/board/keymile/km82xx/Makefile +++ b/board/keymile/km82xx/Makefile @@ -5,7 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif obj-y := km82xx.o ../common/common.o ../common/ivm.o diff --git a/board/keymile/km83xx/Makefile b/board/keymile/km83xx/Makefile index 7bdddf3..6c32688 100644 --- a/board/keymile/km83xx/Makefile +++ b/board/keymile/km83xx/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y += km83xx.o ../common/common.o ../common/ivm.o km83xx_i2c.o diff --git a/board/keymile/km_arm/Makefile b/board/keymile/km_arm/Makefile index 32eaa93..a17d8d9 100644 --- a/board/keymile/km_arm/Makefile +++ b/board/keymile/km_arm/Makefile @@ -6,10 +6,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := km_arm.o ../common/common.o ../common/ivm.o ifdef CONFIG_KM_FPGA_CONFIG diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile index 64eb37c..3e69ee2 100644 --- a/board/keymile/kmp204x/Makefile +++ b/board/keymile/kmp204x/Makefile @@ -8,9 +8,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - -obj-y := $(BOARD).o ddr.o eth.o tlb.o pci.o law.o \ +obj-y := kmp204x.o ddr.o eth.o tlb.o pci.o law.o \ ../common/common.o ../common/ivm.o diff --git a/board/kmc/kzm9g/kzm9g.c b/board/kmc/kzm9g/kzm9g.c index b669ffe..ea36fa4 100644 --- a/board/kmc/kzm9g/kzm9g.c +++ b/board/kmc/kzm9g/kzm9g.c @@ -289,7 +289,6 @@ void adjust_core_voltage(void) { u8 data; - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); data = 0x35; i2c_set_bus_num(0); i2c_write(0x40, 3, 1, &data, 1); diff --git a/board/kup/kup4k/Makefile b/board/kup/kup4k/Makefile index b3ad86c..c896fcd 100644 --- a/board/kup/kup4k/Makefile +++ b/board/kup/kup4k/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = kup4k.o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o diff --git a/board/kup/kup4x/Makefile b/board/kup/kup4x/Makefile index 05a1afc..6945943 100644 --- a/board/kup/kup4x/Makefile +++ b/board/kup/kup4x/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = kup4x.o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c index b6c68da..1569905 100644 --- a/board/logicpd/am3517evm/am3517evm.c +++ b/board/logicpd/am3517evm/am3517evm.c @@ -98,8 +98,8 @@ static void am3517_evm_musb_init(void) */ int misc_init_r(void) { -#ifdef CONFIG_DRIVER_OMAP34XX_I2C - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#ifdef CONFIG_SYS_I2C_OMAP34XX + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif dieid_num_r(); diff --git a/board/matrix_vision/mvsmr/u-boot.lds b/board/matrix_vision/mvsmr/u-boot.lds index 08ce014..e885b7c 100644 --- a/board/matrix_vision/mvsmr/u-boot.lds +++ b/board/matrix_vision/mvsmr/u-boot.lds @@ -18,7 +18,7 @@ SECTIONS /* the first two sectors (=8KB) of our S29GL flash chip */ arch/powerpc/cpu/mpc5xxx/start.o (.text*) arch/powerpc/cpu/mpc5xxx/traps.o (.text*) - board/matrix_vision/common/libmatrix_vision.o (.text*) + board/matrix_vision/common/built-in.o (.text*) /* This is only needed to force failure if size of above code will ever */ /* increase and grow into reserved space. */ diff --git a/board/mpl/mip405/Makefile b/board/mpl/mip405/Makefile index 509eb59..5bcf130 100644 --- a/board/mpl/mip405/Makefile +++ b/board/mpl/mip405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = mip405.o cmd_mip405.o \ ../common/pci.o \ ../common/usb_uhci.o \ diff --git a/board/mpl/pati/Makefile b/board/mpl/pati/Makefile index 67381c1..9822082 100644 --- a/board/mpl/pati/Makefile +++ b/board/mpl/pati/Makefile @@ -5,9 +5,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := pati.o cmd_pati.o \ ../common/common_util.o diff --git a/board/mpl/pip405/Makefile b/board/mpl/pip405/Makefile index 3d73cc3..0a3d059 100644 --- a/board/mpl/pip405/Makefile +++ b/board/mpl/pip405/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y = pip405.o cmd_pip405.o \ ../common/pci.o \ ../common/isa.o \ diff --git a/board/mpl/vcma9/Makefile b/board/mpl/vcma9/Makefile index e0e9669..175a19f 100644 --- a/board/mpl/vcma9/Makefile +++ b/board/mpl/vcma9/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := ../common/common_util.o obj-y += vcma9.o cmd_vcma9.o diff --git a/board/mvblue/u-boot.lds b/board/mvblue/u-boot.lds index 121354b..5034a96 100644 --- a/board/mvblue/u-boot.lds +++ b/board/mvblue/u-boot.lds @@ -14,12 +14,12 @@ SECTIONS .text : { arch/powerpc/cpu/mpc824x/start.o (.text*) - lib/libgeneric.o (.text*) - net/libnet.o (.text*) - drivers/pci/libpci.o (.text*) - arch/powerpc/cpu/mpc824x/libmpc824x.o (.text*) - board/mvblue/libmvblue.o (.text*) - arch/powerpc/lib/libpowerpc.o (.text*) + lib/built-in.o (.text*) + net/built-in.o (.text*) + drivers/pci/built-in.o (.text*) + arch/powerpc/cpu/mpc824x/built-in.o (.text*) + board/mvblue/built-in.o (.text*) + arch/powerpc/lib/built-in.o (.text*) . = DEFINED(env_offset) ? env_offset : .; common/env_embedded.o (.ppcenv*) diff --git a/board/nvidia/beaver/Makefile b/board/nvidia/beaver/Makefile index f828f52..1f7c31d 100644 --- a/board/nvidia/beaver/Makefile +++ b/board/nvidia/beaver/Makefile @@ -14,6 +14,4 @@ # along with this program. If not, see <http://www.gnu.org/licenses/>. # -$(shell mkdir -p $(obj)../cardhu) - obj-y = ../cardhu/cardhu.o diff --git a/board/nvidia/ventana/Makefile b/board/nvidia/ventana/Makefile index 7265cfc..f67044f 100644 --- a/board/nvidia/ventana/Makefile +++ b/board/nvidia/ventana/Makefile @@ -5,6 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)../seaboard) - obj-y = ../seaboard/seaboard.o diff --git a/board/overo/overo.c b/board/overo/overo.c index aace42a..9ac35d2 100644 --- a/board/overo/overo.c +++ b/board/overo/overo.c @@ -92,7 +92,7 @@ int get_board_revision(void) { int revision; -#ifdef CONFIG_DRIVER_OMAP34XX_I2C +#ifdef CONFIG_SYS_I2C_OMAP34XX unsigned char data; /* board revisions <= R2410 connect 4030 irq_1 to gpio112 */ diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c index dafb1eb..034886a 100644 --- a/board/phytec/pcm051/board.c +++ b/board/phytec/pcm051/board.c @@ -91,7 +91,7 @@ void set_mux_conf_regs(void) { /* Initalize the board header */ enable_i2c0_pin_mux(); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); enable_board_pin_mux(); } @@ -108,7 +108,7 @@ void sdram_init(void) */ int board_init(void) { - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; diff --git a/board/prodrive/p3mx/Makefile b/board/prodrive/p3mx/Makefile index 43caffb..6ddda22 100644 --- a/board/prodrive/p3mx/Makefile +++ b/board/prodrive/p3mx/Makefile @@ -5,10 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../../Marvell/common) -endif - obj-y = misc.o obj-y += p3mx.o mpsc.o mv_eth.o pci.o sdram_init.o serial.o \ ../../Marvell/common/i2c.o ../../Marvell/common/memory.o diff --git a/board/psyent/pci5441/Makefile b/board/psyent/pci5441/Makefile index 9a66cfd..364f163 100644 --- a/board/psyent/pci5441/Makefile +++ b/board/psyent/pci5441/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := pci5441.o ../common/AMDLV065D.o diff --git a/board/psyent/pci5441/config.mk b/board/psyent/pci5441/config.mk index 00ff743..776fa8a 100644 --- a/board/psyent/pci5441/config.mk +++ b/board/psyent/pci5441/config.mk @@ -8,7 +8,6 @@ CONFIG_SYS_TEXT_BASE = 0x018e0000 PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul -PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include ifeq ($(debug),1) PLATFORM_CPPFLAGS += -DDEBUG diff --git a/board/psyent/pk1c20/Makefile b/board/psyent/pk1c20/Makefile index 286db94..5450f93 100644 --- a/board/psyent/pk1c20/Makefile +++ b/board/psyent/pk1c20/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - obj-y := pk1c20.o led.o ../common/AMDLV065D.o diff --git a/board/psyent/pk1c20/config.mk b/board/psyent/pk1c20/config.mk index 7b0810a..83cfadc 100644 --- a/board/psyent/pk1c20/config.mk +++ b/board/psyent/pk1c20/config.mk @@ -8,7 +8,6 @@ CONFIG_SYS_TEXT_BASE = 0x01fc0000 PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul -PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include ifeq ($(debug),1) PLATFORM_CPPFLAGS += -DDEBUG diff --git a/board/rbc823/u-boot.lds b/board/rbc823/u-boot.lds index 191f9eb..7676cf4 100644 --- a/board/rbc823/u-boot.lds +++ b/board/rbc823/u-boot.lds @@ -19,10 +19,10 @@ SECTIONS arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - lib/libgeneric.o (.text*) - net/libnet.o (.text*) - arch/powerpc/cpu/mpc8xx/libmpc8xx.o (.text*) - arch/powerpc/lib/libpowerpc.o (.text*) + lib/built-in.o (.text*) + net/built-in.o (.text*) + arch/powerpc/cpu/mpc8xx/built-in.o (.text*) + arch/powerpc/lib/built-in.o (.text*) . = env_offset; common/env_embedded.o (.text*) diff --git a/board/renesas/ecovec/ecovec.c b/board/renesas/ecovec/ecovec.c index e2d365a..fb4acf3 100644 --- a/board/renesas/ecovec/ecovec.c +++ b/board/renesas/ecovec/ecovec.c @@ -57,8 +57,7 @@ int board_late_init(void) outl(inl(MSTPCR2) & ~0x10000000, MSTPCR2); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE); /* Use I2C 1 */ + i2c_set_bus_num(1); /* Use I2C 1 */ /* Read MAC address */ i2c_read(0x50, 0x10, 0, mac, 6); diff --git a/board/sandburst/karef/Makefile b/board/sandburst/karef/Makefile index 05c8187..f890008 100644 --- a/board/sandburst/karef/Makefile +++ b/board/sandburst/karef/Makefile @@ -9,10 +9,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - # TBS: add for debugging purposes BUILDUSER := $(shell whoami) FORCEBUILD := $(shell rm -f karef.o) diff --git a/board/sandburst/metrobox/Makefile b/board/sandburst/metrobox/Makefile index 76dfffc..37d91a5 100644 --- a/board/sandburst/metrobox/Makefile +++ b/board/sandburst/metrobox/Makefile @@ -8,10 +8,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - # TBS: add for debugging purposes BUILDUSER := $(shell whoami) FORCEBUILD := $(shell rm -f metrobox.o) diff --git a/board/siemens/common/board.c b/board/siemens/common/board.c index 6279c32..32d2ee4 100644 --- a/board/siemens/common/board.c +++ b/board/siemens/common/board.c @@ -42,7 +42,7 @@ void set_mux_conf_regs(void) { /* Initalize the board header */ enable_i2c0_pin_mux(); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); if (read_eeprom() < 0) puts("Could not get board ID.\n"); @@ -67,7 +67,7 @@ int board_init(void) #if defined(CONFIG_HW_WATCHDOG) hw_watchdog_init(); #endif /* defined(CONFIG_HW_WATCHDOG) */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); if (read_eeprom() < 0) puts("Could not get board ID.\n"); diff --git a/board/siemens/dxr2/Makefile b/board/siemens/dxr2/Makefile index 5129c6e..f159932 100644 --- a/board/siemens/dxr2/Makefile +++ b/board/siemens/dxr2/Makefile @@ -11,10 +11,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - ifdef CONFIG_SPL_BUILD obj-y := mux.o endif diff --git a/board/siemens/pxm2/Makefile b/board/siemens/pxm2/Makefile index 5129c6e..f159932 100644 --- a/board/siemens/pxm2/Makefile +++ b/board/siemens/pxm2/Makefile @@ -11,10 +11,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - ifdef CONFIG_SPL_BUILD obj-y := mux.o endif diff --git a/board/siemens/rut/Makefile b/board/siemens/rut/Makefile index 5129c6e..f159932 100644 --- a/board/siemens/rut/Makefile +++ b/board/siemens/rut/Makefile @@ -11,10 +11,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - ifdef CONFIG_SPL_BUILD obj-y := mux.o endif diff --git a/board/spd8xx/u-boot.lds b/board/spd8xx/u-boot.lds index 2a68934..463af7e 100644 --- a/board/spd8xx/u-boot.lds +++ b/board/spd8xx/u-boot.lds @@ -18,8 +18,8 @@ SECTIONS arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - net/libnet.o (.text*) - arch/powerpc/cpu/mpc8xx/libmpc8xx.o (.text*) + net/built-in.o (.text*) + arch/powerpc/cpu/mpc8xx/built-in.o (.text*) *(.text.v*printf) . = DEFINED(env_offset) ? env_offset : .; diff --git a/board/svm_sc8xx/u-boot.lds b/board/svm_sc8xx/u-boot.lds index 4922625..df564e9 100644 --- a/board/svm_sc8xx/u-boot.lds +++ b/board/svm_sc8xx/u-boot.lds @@ -17,11 +17,11 @@ SECTIONS /* the sector layout of our flash chips! XXX FIXME XXX */ arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - lib/libgeneric.o (.text*) - net/libnet.o (.text*) - arch/powerpc/cpu/mpc8xx/libmpc8xx.o (.text*) - arch/powerpc/lib/libpowerpc.o (.text*) - board/svm_sc8xx/libsvm_sc8xx.o (.text*) + lib/built-in.o (.text*) + net/built-in.o (.text*) + arch/powerpc/cpu/mpc8xx/built-in.o (.text*) + arch/powerpc/lib/built-in.o (.text*) + board/svm_sc8xx/built-in.o (.text*) *(.text.*printf) *(.text.do_mem_*) *(.text.flash*) diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index 57fedab..8edd21b 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -397,7 +397,7 @@ const struct dpll_params *get_dpll_ddr_params(void) struct am335x_baseboard_id header; enable_i2c0_pin_mux(); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); if (read_eeprom(&header) < 0) puts("Could not get board ID.\n"); diff --git a/board/ti/am335x/u-boot.lds b/board/ti/am335x/u-boot.lds index a173f62..e77a501 100644 --- a/board/ti/am335x/u-boot.lds +++ b/board/ti/am335x/u-boot.lds @@ -35,7 +35,7 @@ SECTIONS { *(.__image_copy_start) CPUDIR/start.o (.text*) - board/ti/am335x/libam335x.o (.text*) + board/ti/am335x/built-in.o (.text*) *(.text*) } diff --git a/board/ti/am3517crane/am3517crane.c b/board/ti/am3517crane/am3517crane.c index 5eb97ff..a649697 100644 --- a/board/ti/am3517crane/am3517crane.c +++ b/board/ti/am3517crane/am3517crane.c @@ -43,8 +43,8 @@ int board_init(void) */ int misc_init_r(void) { -#ifdef CONFIG_DRIVER_OMAP34XX_I2C - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#ifdef CONFIG_SYS_I2C_OMAP34XX + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif dieid_num_r(); diff --git a/board/ti/beagle/Makefile b/board/ti/beagle/Makefile index 9f55e8f..7a858be 100644 --- a/board/ti/beagle/Makefile +++ b/board/ti/beagle/Makefile @@ -5,5 +5,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-y := $(BOARD).o +obj-y := beagle.o obj-$(CONFIG_STATUS_LED) += led.o diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c index c71c218..81dd081 100644 --- a/board/ti/evm/evm.c +++ b/board/ti/evm/evm.c @@ -146,8 +146,8 @@ void get_board_mem_timings(struct board_sdrc_timings *timings) int misc_init_r(void) { -#ifdef CONFIG_DRIVER_OMAP34XX_I2C - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#ifdef CONFIG_SYS_I2C_OMAP34XX + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); #endif #if defined(CONFIG_CMD_NET) diff --git a/board/toradex/colibri_t20_iris/Makefile b/board/toradex/colibri_t20_iris/Makefile index 7ca3fe5..ebeac70 100644 --- a/board/toradex/colibri_t20_iris/Makefile +++ b/board/toradex/colibri_t20_iris/Makefile @@ -4,9 +4,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)../../nvidia/common) -$(shell mkdir -p $(obj)../colibri_t20-common) - obj-y := ../../nvidia/common/board.o obj-y += ../colibri_t20-common/colibri_t20-common.o obj-y += colibri_t20_iris.o diff --git a/board/tqc/tqm8260/Makefile b/board/tqc/tqm8260/Makefile index dc4a528..6b8573d 100644 --- a/board/tqc/tqm8260/Makefile +++ b/board/tqc/tqm8260/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../tqm8xx/) -endif - obj-y = tqm8260.o ../tqm8xx/load_sernum_ethaddr.o diff --git a/board/tqc/tqm8272/Makefile b/board/tqc/tqm8272/Makefile index 09af765..8bf0241 100644 --- a/board/tqc/tqm8272/Makefile +++ b/board/tqc/tqm8272/Makefile @@ -5,8 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../tqm8xx/) -endif - obj-y = tqm8272.o ../tqm8xx/load_sernum_ethaddr.o nand.o diff --git a/board/tqc/tqm8xx/u-boot.lds b/board/tqc/tqm8xx/u-boot.lds index cbfc94f..b77ae56 100644 --- a/board/tqc/tqm8xx/u-boot.lds +++ b/board/tqc/tqm8xx/u-boot.lds @@ -18,13 +18,13 @@ SECTIONS arch/powerpc/cpu/mpc8xx/start.o (.text*) arch/powerpc/cpu/mpc8xx/traps.o (.text*) - arch/powerpc/cpu/mpc8xx/libmpc8xx.o (.text*) - arch/powerpc/lib/libpowerpc.o (.text*) - board/tqc/tqm8xx/libtqm8xx.o (.text*) - disk/libdisk.o (.text*) - drivers/net/libnet.o (.text*) - drivers/libdrivers.o (.text.pcmcia_on) - drivers/libdrivers.o (.text.pcmcia_hardware_enable) + arch/powerpc/cpu/mpc8xx/built-in.o (.text*) + arch/powerpc/lib/built-in.o (.text*) + board/tqc/tqm8xx/built-in.o (.text*) + disk/built-in.o (.text*) + drivers/net/built-in.o (.text*) + drivers/built-in.o (.text.pcmcia_on) + drivers/built-in.o (.text.pcmcia_hardware_enable) . = DEFINED(env_offset) ? env_offset : .; common/env_embedded.o (.ppcenv*) diff --git a/board/vpac270/u-boot-spl.lds b/board/vpac270/u-boot-spl.lds index 7eac497..c9b50e9 100644 --- a/board/vpac270/u-boot-spl.lds +++ b/board/vpac270/u-boot-spl.lds @@ -20,8 +20,8 @@ SECTIONS .text.0 : { arch/arm/cpu/pxa/start.o (.text*) - board/vpac270/libvpac270.o (.text*) - drivers/mtd/onenand/libonenand.o (.text*) + board/vpac270/built-in.o (.text*) + drivers/mtd/onenand/built-in.o (.text*) } diff --git a/board/xilinx/ppc405-generic/Makefile b/board/xilinx/ppc405-generic/Makefile index 1562f17..c9da870 100644 --- a/board/xilinx/ppc405-generic/Makefile +++ b/board/xilinx/ppc405-generic/Makefile @@ -9,8 +9,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../../xilinx/ppc405-generic) -endif - obj-y += ../../xilinx/ppc405-generic/xilinx_ppc405_generic.o diff --git a/board/xilinx/ppc440-generic/Makefile b/board/xilinx/ppc440-generic/Makefile index b2227c5..0acd95d 100644 --- a/board/xilinx/ppc440-generic/Makefile +++ b/board/xilinx/ppc440-generic/Makefile @@ -9,9 +9,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../../xilinx/ppc440-generic) -endif - obj-y += ../../xilinx/ppc440-generic/xilinx_ppc440_generic.o extra-y += ../../xilinx/ppc440-generic/init.o @@ -963,6 +963,8 @@ Active powerpc mpc85xx - freescale t4qds Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 - Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 - Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Naveen Burmi <NaveenBurmi@freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1040RDB T1040RDB:PPC_T1040 Poonam Aggrwal <poonam.aggrwal@freescale.com> +Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T1042RDB_PI:PPC_T1042 Poonam Aggrwal <poonam.aggrwal@freescale.com> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach@gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach@gdsys.de> Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach@gdsys.de> diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c index ef694d8..02539c4 100644 --- a/common/cmd_eeprom.c +++ b/common/cmd_eeprom.c @@ -161,7 +161,7 @@ int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C) spi_read (addr, alen, buffer, len); #else - if (i2c_read (addr[0], offset, alen-1, buffer, len) != 0) + if (i2c_read (addr[0], addr[1], alen-1, buffer, len) != 0) rcode = 1; #endif buffer += len; @@ -339,7 +339,7 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cn /* Write is enabled ... now write eeprom value. */ #endif - if (i2c_write (addr[0], offset, alen-1, buffer, len) != 0) + if (i2c_write (addr[0], addr[1], alen-1, buffer, len) != 0) rcode = 1; #endif @@ -13,12 +13,6 @@ SHELL := $(shell if [ -x "$$BASH" ]; then echo $$BASH; \ export SHELL -ifeq ($(CONFIG_TPL_BUILD),y) -SPL_BIN := u-boot-tpl -else -SPL_BIN := u-boot-spl -endif - ifeq ($(CURDIR),$(SRCTREE)) dir := else diff --git a/doc/README.p1010rdb b/doc/README.p1010rdb deleted file mode 100644 index 6b2b5ff..0000000 --- a/doc/README.p1010rdb +++ /dev/null @@ -1,198 +0,0 @@ -Overview -========= -The P1010RDB is a Freescale reference design board that hosts the P1010 SoC. - -The P1010 is a cost-effective, low-power, highly integrated host processor -based on a Power Architecture e500v2 core (maximum core frequency 800/1000 MHz), -that addresses the requirements of several routing, gateways, storage, consumer, -and industrial applications. Applications of interest include the main CPUs and -I/O processors in network attached storage (NAS), the voice over IP (VoIP) -router/gateway, and wireless LAN (WLAN) and industrial controllers. - -The P1010RDB board features are as follows: -Memory subsystem: - - 1Gbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus) - - 32 Mbyte NOR flash single-chip memory - - 32 Mbyte NAND flash memory - - 256 Kbit M24256 I2C EEPROM - - 16 Mbyte SPI memory - - I2C Board EEPROM 128x8 bit memory - - SD/MMC connector to interface with the SD memory card -Interfaces: - - PCIe: - - Lane0: x1 mini-PCIe slot - - Lane1: x1 PCIe standard slot - - SATA: - - 1 internal SATA connector to 2.5" 160G SATA2 HDD - - 1 eSATA connector to rear panel - - 10/100/1000 BaseT Ethernet ports: - - eTSEC1, RGMII: one 10/100/1000 port using Vitesse VSC8641XKO - - eTSEC2, SGMII: one 10/100/1000 port using Vitesse VSC8221 - - eTSEC3, SGMII: one 10/100/1000 port using Vitesse VSC8221 - - USB 2.0 port: - - x1 USB2.0 port: via an ULPI PHY to micro-AB connector - - x1 USB2.0 poort via an internal PHY to micro-AB connector - - FlexCAN ports: - - x2 DB-9 female connectors for FlexCAN bus(revision 2.0B) - interface; - - DUART interface: - - DUART interface: supports two UARTs up to 115200 bps for - console display - - J45 connectors are used for these 2 UART ports. - - TDM - - 2 FXS ports connected via an external SLIC to the TDM - interface. SLIC is controllled via SPI. - - 1 FXO port connected via a relay to FXS for switchover to - POTS -Board connectors: - - Mini-ITX power supply connector - - JTAG/COP for debugging -IEEE Std. 1588 signals for test and measurement -Real-time clock on I2C bus -POR - - support critical POR setting changed via switch on board -PCB - - 6-layer routing (4-layer signals, 2-layer power and ground) - - -Serial Port Configuration on P1010RDB -===================================== -Configure the serial port of the attached computer with the following values: - -Data rate: 115200 bps - -Number of data bits: 8 - -Parity: None - -Number of Stop bits: 1 - -Flow Control: Hardware/None - - -Settings of DIP-switch -====================== - SW4[1:4]= 1111 and SW6[4]=0 for boot from 16bit NOR flash - SW4[1:4]= 1000 and SW6[4]=1 for boot from 8bit NAND flash - SW4[1:4]= 0110 and SW6[4]=0 for boot from SPI flash -Note: 1 stands for 'on', 0 stands for 'off' - - -Setting of hwconfig -=================== -If FlexCAN or TDM is needed, please set "fsl_p1010mux:tdm_can=can" or -"fsl_p1010mux:tdm_can=tdm" explicitly in u-booot prompt as below for example: -setenv hwconfig "fsl_p1010mux:tdm_can=tdm;usb1:dr_mode=host,phy_type=utmi" -By default, don't set fsl_p1010mux:tdm_can, in this case, spi chip selection -is set to spi-flash instead of to SLIC/TDM/DAC and tdm_can_sel is set to TDM -instead of to CAN/UART1. - - -Build and burn u-boot to NOR flash -================================== -1. Build u-boot.bin image - export ARCH=powerpc - export CROSS_COMPILE=/your_path/powerpc-linux-gnu- - make P1010RDB_NOR - -2. Burn u-boot.bin into NOR flash - => tftp $loadaddr $uboot - => protect off eff80000 +$filesize - => erase eff80000 +$filesize - => cp.b $loadaddr eff80000 $filesize - -3. Check SW4[1:4]= 1111 and SW6[4]=0, then power on. - - -Alternate NOR bank -============================ -1. Burn u-boot.bin into alternate NOR bank - => tftp $loadaddr $uboot - => protect off eef80000 +$filesize - => erase eef80000 +$filesize - => cp.b $loadaddr eef80000 $filesize - -2. Switch to alternate NOR bank - => mw.b ffb00009 1 - => reset - or set SW1[8]= ON - -SW1[8]= OFF: Upper bank used for booting start -SW1[8]= ON: Lower bank used for booting start -CPLD NOR bank selection register address 0xFFB00009 Bit[0]: -0 - boot from upper 4 sectors -1 - boot from lower 4 sectors - - -Build and burn u-boot to NAND flash -=================================== -1. Build u-boot.bin image - export ARCH=powerpc - export CROSS_COMPILE=/your_path/powerpc-linux-gnu- - make P1010RDB_NAND - -2. Burn u-boot-nand.bin into NAND flash - => tftp $loadaddr $uboot-nand - => nand erase 0 $filesize - => nand write $loadaddr 0 $filesize - -3. Check SW4[1:4]= 1000 and SW6[4]=1, then power on. - - - -Build and burn u-boot to SPI flash -================================== -1. Build u-boot-spi.bin image - make P1010RDB_SPIFLASH_config; make - Boot up kernel with rootfs.ext2.gz.uboot.p1010rdb - Download u-boot.bin to linux and you can find some config files - under /usr/share such as config_xx.dat. Do below command: - boot_format config_ddr3_1gb_p1010rdb_800M.dat u-boot.bin -spi \ - u-boot-spi.bin - to generate u-boot-spi.bin. - -2. Burn u-boot-spi.bin into SPI flash - => tftp $loadaddr $uboot-spi - => sf erase 0 100000 - => sf write $loadaddr 0 $filesize - -3. Check SW4[1:4]= 0110 and SW6[4]=0, then power on. - - - -CPLD POR setting registers -========================== -1. Set POR switch selection register (addr 0xFFB00011) to 0. -2. Write CPLD POR registers (BCSR0~BCSR3, addr 0xFFB00014~0xFFB00017) with - proper values. - If change boot ROM location to NOR or NAND flash, need write the IFC_CS0 - switch command by I2C. -3. Send reset command. - After reset, the new POR setting will be implemented. - -Two examples are given in below: -Switch from NOR to NAND boot with default frequency: - => i2c dev 0 - => i2c mw 18 1 f9 - => i2c mw 18 3 f0 - => mw.b ffb00011 0 - => mw.b ffb00017 1 - => reset -Switch from NAND to NOR boot with Core/CCB/DDR (800/400/667 MHz): - => i2c dev 0 - => i2c mw 18 1 f1 - => i2c mw 18 3 f0 - => mw.b ffb00011 0 - => mw.b ffb00014 2 - => mw.b ffb00015 5 - => mw.b ffb00016 3 - => mw.b ffb00017 f - => reset - - -Boot Linux from network using TFTP on P1010RDB -============================================== -Place uImage, p1010rdb.dtb and rootfs files in the TFTP disk area. - => tftp 1000000 uImage - => tftp 2000000 p1010rdb.dtb - => tftp 3000000 rootfs.ext2.gz.uboot.p1010rdb - => bootm 1000000 3000000 2000000 - - -Please contact your local field applications engineer or sales representative -to obtain related documents, such as P1010-RDB User Guide for details. diff --git a/doc/README.scrapyard b/doc/README.scrapyard index c3182e4..f045f43 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -103,3 +103,4 @@ CPCI440 powerpc 440GP b568fd2 2007-12-27 Matthias Fuc PCIPPC2 powerpc MPC740/MPC750 7c9e89b 2013-02-07 Wolfgang Denk <wd@denx.de> PCIPPC6 powerpc MPC740/MPC750 - - Wolfgang Denk <wd@denx.de> omap2420h4 arm omap24xx - 2013-06-04 Richard Woodruff <r-woodruff2@ti.com> +eNET x86 x86 7e8c53d 2013-02-14 Graeme Russ <graeme.russ@gmail.com> diff --git a/drivers/Makefile b/drivers/Makefile index 9cec2ba..5d03f37 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -1,8 +1,8 @@ -obj-y += bios_emulator/ +obj-$(CONFIG_BIOSEMU) += bios_emulator/ obj-y += block/ obj-$(CONFIG_BOOTCOUNT_LIMIT) += bootcount/ obj-y += crypto/ -obj-y += fpga/ +obj-$(CONFIG_FPGA) += fpga/ obj-y += hwmon/ obj-y += misc/ obj-y += pcmcia/ @@ -13,3 +13,4 @@ obj-y += tpm/ obj-y += twserial/ obj-y += video/ obj-y += watchdog/ +obj-$(CONFIG_QE) += qe/ diff --git a/drivers/bios_emulator/Makefile b/drivers/bios_emulator/Makefile index dd42e0f..6f74fdc 100644 --- a/drivers/bios_emulator/Makefile +++ b/drivers/bios_emulator/Makefile @@ -1,8 +1,6 @@ X86DIR = x86emu -$(shell mkdir -p $(obj)$(X86DIR)) - -obj-$(CONFIG_BIOSEMU) = atibios.o biosemu.o besys.o bios.o \ +obj-y = atibios.o biosemu.o besys.o bios.o \ $(X86DIR)/decode.o \ $(X86DIR)/ops2.o \ $(X86DIR)/ops.o \ diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index 4fcdf40..dfb2e7f 100644 --- a/drivers/fpga/Makefile +++ b/drivers/fpga/Makefile @@ -5,7 +5,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifdef CONFIG_FPGA obj-y += fpga.o obj-$(CONFIG_FPGA_SPARTAN2) += spartan2.o obj-$(CONFIG_FPGA_SPARTAN3) += spartan3.o @@ -19,4 +18,3 @@ obj-$(CONFIG_FPGA_ACEX1K) += ACEX1K.o obj-$(CONFIG_FPGA_CYCLON2) += cyclon2.o obj-$(CONFIG_FPGA_STRATIX_II) += stratixII.o endif -endif diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index 5280bb3..553b519 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -11,21 +11,20 @@ obj-$(CONFIG_DW_I2C) += designware_i2c.o obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o obj-$(CONFIG_I2C_MV) += mv_i2c.o obj-$(CONFIG_I2C_MXS) += mxs_i2c.o -obj-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o -obj-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o -obj-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o obj-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o obj-$(CONFIG_U8500_I2C) += u8500_i2c.o -obj-$(CONFIG_SH_I2C) += sh_i2c.o obj-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o obj-$(CONFIG_SYS_I2C) += i2c_core.o obj-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o obj-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o obj-$(CONFIG_SYS_I2C_MXC) += mxc_i2c.o +obj-$(CONFIG_SYS_I2C_OMAP24XX) += omap24xx_i2c.o +obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o obj-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o +obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o -obj-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o +obj-$(CONFIG_SYS_I2C_ZYNQ) += zynq_i2c.o diff --git a/drivers/i2c/designware_i2c.c b/drivers/i2c/designware_i2c.c index c2f0662..cb2ac04 100644 --- a/drivers/i2c/designware_i2c.c +++ b/drivers/i2c/designware_i2c.c @@ -151,7 +151,19 @@ void i2c_init(int speed, int slaveadd) */ static void i2c_setaddress(unsigned int i2c_addr) { + unsigned int enbl; + + /* Disable i2c */ + enbl = readl(&i2c_regs_p->ic_enable); + enbl &= ~IC_ENABLE_0B; + writel(enbl, &i2c_regs_p->ic_enable); + writel(i2c_addr, &i2c_regs_p->ic_tar); + + /* Enable i2c */ + enbl = readl(&i2c_regs_p->ic_enable); + enbl |= IC_ENABLE_0B; + writel(enbl, &i2c_regs_p->ic_enable); } /* @@ -237,9 +249,6 @@ static int i2c_xfer_finish(void) i2c_flush_rxfifo(); - /* Wait for read/write operation to complete on actual memory */ - udelay(10000); - return 0; } diff --git a/drivers/i2c/mxs_i2c.c b/drivers/i2c/mxs_i2c.c index 46106b7..a298c95 100644 --- a/drivers/i2c/mxs_i2c.c +++ b/drivers/i2c/mxs_i2c.c @@ -150,6 +150,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) { struct mxs_i2c_regs *i2c_regs = (struct mxs_i2c_regs *)MXS_I2C0_BASE; uint32_t tmp = 0; + int timeout = MXS_I2C_MAX_TIMEOUT; int ret; int i; @@ -169,9 +170,17 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) for (i = 0; i < len; i++) { if (!(i & 3)) { - while (readl(&i2c_regs->hw_i2c_queuestat) & - I2C_QUEUESTAT_RD_QUEUE_EMPTY) - ; + while (--timeout) { + tmp = readl(&i2c_regs->hw_i2c_queuestat); + if (!(tmp & I2C_QUEUESTAT_RD_QUEUE_EMPTY)) + break; + } + + if (!timeout) { + debug("MXS I2C: Failed receiving data!\n"); + return -ETIMEDOUT; + } + tmp = readl(&i2c_regs->hw_i2c_queuedata); } buffer[i] = tmp & 0xff; diff --git a/drivers/i2c/omap1510_i2c.c b/drivers/i2c/omap1510_i2c.c deleted file mode 100644 index f91ee88..0000000 --- a/drivers/i2c/omap1510_i2c.c +++ /dev/null @@ -1,277 +0,0 @@ -/* - * Basic I2C functions - * - * Copyright (c) 2003 Texas Instruments - * - * This package is free software; you can redistribute it and/or - * modify it under the terms of the license found in the file - * named COPYING that should have accompanied this file. - * - * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR - * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED - * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. - * - * Author: Jian Zhang jzhang@ti.com, Texas Instruments - * - * Copyright (c) 2003 Wolfgang Denk, wd@denx.de - * Rewritten to fit into the current U-Boot framework - * - */ - -#include <common.h> - -static void wait_for_bb (void); -static u16 wait_for_pin (void); - -void i2c_init (int speed, int slaveadd) -{ - u16 scl; - - if (inw (I2C_CON) & I2C_CON_EN) { - outw (0, I2C_CON); - udelay (5000); - } - - /* 12MHz I2C module clock */ - outw (0, I2C_PSC); - outw (I2C_CON_EN, I2C_CON); - outw (0, I2C_SYSTEST); - /* have to enable intrrupts or OMAP i2c module doesn't work */ - outw (I2C_IE_XRDY_IE | I2C_IE_RRDY_IE | I2C_IE_ARDY_IE | - I2C_IE_NACK_IE | I2C_IE_AL_IE, I2C_IE); - scl = (12000000 / 2) / speed - 6; - outw (scl, I2C_SCLL); - outw (scl, I2C_SCLH); - /* own address */ - outw (slaveadd, I2C_OA); - outw (0, I2C_CNT); - udelay (1000); -} - -static int i2c_read_byte (u8 devaddr, u8 regoffset, u8 * value) -{ - int i2c_error = 0; - u16 status; - - /* wait until bus not busy */ - wait_for_bb (); - - /* one byte only */ - outw (1, I2C_CNT); - /* set slave address */ - outw (devaddr, I2C_SA); - /* no stop bit needed here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX, I2C_CON); - - status = wait_for_pin (); - - if (status & I2C_STAT_XRDY) { - /* Important: have to use byte access */ - *(volatile u8 *) (I2C_DATA) = regoffset; - udelay (20000); - if (inw (I2C_STAT) & I2C_STAT_NACK) { - i2c_error = 1; - } - } else { - i2c_error = 1; - } - - if (!i2c_error) { - /* free bus, otherwise we can't use a combined transction */ - outw (0, I2C_CON); - while (inw (I2C_STAT) || (inw (I2C_CON) & I2C_CON_MST)) { - udelay (10000); - /* Have to clear pending interrupt to clear I2C_STAT */ - inw (I2C_IV); - } - - wait_for_bb (); - /* set slave address */ - outw (devaddr, I2C_SA); - /* read one byte from slave */ - outw (1, I2C_CNT); - /* need stop bit here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP, - I2C_CON); - - status = wait_for_pin (); - if (status & I2C_STAT_RRDY) { - *value = inw (I2C_DATA); - udelay (20000); - } else { - i2c_error = 1; - } - - if (!i2c_error) { - outw (I2C_CON_EN, I2C_CON); - while (inw (I2C_STAT) - || (inw (I2C_CON) & I2C_CON_MST)) { - udelay (10000); - inw (I2C_IV); - } - } - } - - return i2c_error; -} - -static int i2c_write_byte (u8 devaddr, u8 regoffset, u8 value) -{ - int i2c_error = 0; - u16 status; - - /* wait until bus not busy */ - wait_for_bb (); - - /* two bytes */ - outw (2, I2C_CNT); - /* set slave address */ - outw (devaddr, I2C_SA); - /* stop bit needed here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX | - I2C_CON_STP, I2C_CON); - - /* wait until state change */ - status = wait_for_pin (); - - if (status & I2C_STAT_XRDY) { - /* send out two bytes */ - outw ((value << 8) + regoffset, I2C_DATA); - /* must have enough delay to allow BB bit to go low */ - udelay (30000); - if (inw (I2C_STAT) & I2C_STAT_NACK) { - i2c_error = 1; - } - } else { - i2c_error = 1; - } - - if (!i2c_error) { - outw (I2C_CON_EN, I2C_CON); - while (inw (I2C_STAT) || (inw (I2C_CON) & I2C_CON_MST)) { - udelay (1000); - /* have to read to clear intrrupt */ - inw (I2C_IV); - } - } - - return i2c_error; -} - -int i2c_probe (uchar chip) -{ - int res = 1; - - if (chip == inw (I2C_OA)) { - return res; - } - - /* wait until bus not busy */ - wait_for_bb (); - - /* try to read one byte */ - outw (1, I2C_CNT); - /* set slave address */ - outw (chip, I2C_SA); - /* stop bit needed here */ - outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP, I2C_CON); - /* enough delay for the NACK bit set */ - udelay (2000); - if (!(inw (I2C_STAT) & I2C_STAT_NACK)) { - res = 0; - } else { - outw (inw (I2C_CON) | I2C_CON_STP, I2C_CON); - udelay (20); - wait_for_bb (); - } - - return res; -} - -int i2c_read (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - int i; - - if (alen > 1) { - printf ("I2C read: addr len %d not supported\n", alen); - return 1; - } - - if (addr + len > 256) { - printf ("I2C read: address out of range\n"); - return 1; - } - - for (i = 0; i < len; i++) { - if (i2c_read_byte (chip, addr + i, &buffer[i])) { - printf ("I2C read: I/O error\n"); - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - return 1; - } - } - - return 0; -} - -int i2c_write (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - int i; - - if (alen > 1) { - printf ("I2C read: addr len %d not supported\n", alen); - return 1; - } - - if (addr + len > 256) { - printf ("I2C read: address out of range\n"); - return 1; - } - - for (i = 0; i < len; i++) { - if (i2c_write_byte (chip, addr + i, buffer[i])) { - printf ("I2C read: I/O error\n"); - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - return 1; - } - } - - return 0; -} - -static void wait_for_bb (void) -{ - int timeout = 10; - - while ((inw (I2C_STAT) & I2C_STAT_BB) && timeout--) { - inw (I2C_IV); - udelay (1000); - } - - if (timeout <= 0) { - printf ("timed out in wait_for_bb: I2C_STAT=%x\n", - inw (I2C_STAT)); - } -} - -static u16 wait_for_pin (void) -{ - u16 status, iv; - int timeout = 10; - - do { - udelay (1000); - status = inw (I2C_STAT); - iv = inw (I2C_IV); - } while (!iv && - !(status & - (I2C_STAT_ROVR | I2C_STAT_XUDF | I2C_STAT_XRDY | - I2C_STAT_RRDY | I2C_STAT_ARDY | I2C_STAT_NACK | - I2C_STAT_AL)) && timeout--); - - if (timeout <= 0) { - printf ("timed out in wait_for_pin: I2C_STAT=%x\n", - inw (I2C_STAT)); - } - - return status; -} diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c index ef38d71..3d38c03 100644 --- a/drivers/i2c/omap24xx_i2c.c +++ b/drivers/i2c/omap24xx_i2c.c @@ -35,6 +35,7 @@ */ #include <common.h> +#include <i2c.h> #include <asm/arch/i2c.h> #include <asm/io.h> @@ -48,22 +49,14 @@ DECLARE_GLOBAL_DATA_PTR; /* Absolutely safe for status update at 100 kHz I2C: */ #define I2C_WAIT 200 -static int wait_for_bb(void); -static u16 wait_for_event(void); -static void flush_fifo(void); +static int wait_for_bb(struct i2c_adapter *adap); +static struct i2c *omap24_get_base(struct i2c_adapter *adap); +static u16 wait_for_event(struct i2c_adapter *adap); +static void flush_fifo(struct i2c_adapter *adap); -/* - * For SPL boot some boards need i2c before SDRAM is initialised so force - * variables to live in SRAM - */ -static struct i2c __attribute__((section (".data"))) *i2c_base = - (struct i2c *)I2C_DEFAULT_BASE; -static unsigned int __attribute__((section (".data"))) bus_initialized[I2C_BUS_MAX] = - { [0 ... (I2C_BUS_MAX-1)] = 0 }; -static unsigned int __attribute__((section (".data"))) current_bus = 0; - -void i2c_init(int speed, int slaveadd) +static void omap24_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { + struct i2c *i2c_base = omap24_get_base(adap); int psc, fsscll, fssclh; int hsscll = 0, hssclh = 0; u32 scll, sclh; @@ -163,16 +156,15 @@ void i2c_init(int speed, int slaveadd) I2C_IE_NACK_IE | I2C_IE_AL_IE, &i2c_base->ie); #endif udelay(1000); - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); - - if (gd->flags & GD_FLG_RELOC) - bus_initialized[current_bus] = 1; } -static void flush_fifo(void) -{ u16 stat; +static void flush_fifo(struct i2c_adapter *adap) +{ + struct i2c *i2c_base = omap24_get_base(adap); + u16 stat; /* note: if you try and read data when its not there or ready * you get a bus error @@ -192,8 +184,9 @@ static void flush_fifo(void) * i2c_probe: Use write access. Allows to identify addresses that are * write-only (like the config register of dual-port EEPROMs) */ -int i2c_probe(uchar chip) +static int omap24_i2c_probe(struct i2c_adapter *adap, uchar chip) { + struct i2c *i2c_base = omap24_get_base(adap); u16 status; int res = 1; /* default = fail */ @@ -201,7 +194,7 @@ int i2c_probe(uchar chip) return res; /* Wait until bus is free */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return res; /* No data transfer, slave addr only */ @@ -212,7 +205,7 @@ int i2c_probe(uchar chip) writew(I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX | I2C_CON_STP, &i2c_base->con); - status = wait_for_event(); + status = wait_for_event(adap); if ((status & ~I2C_STAT_XRDY) == 0 || (status & I2C_STAT_AL)) { /* @@ -223,7 +216,7 @@ int i2c_probe(uchar chip) */ if (status == I2C_STAT_XRDY) printf("i2c_probe: pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto pr_exit; } @@ -239,7 +232,7 @@ int i2c_probe(uchar chip) I2C_CON_STP, &i2c_base->con); /* STP */ } pr_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); return res; @@ -258,8 +251,10 @@ pr_exit: * or that do not need a register address at all (such as some clock * distributors). */ -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int omap24_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c *i2c_base = omap24_get_base(adap); int i2c_error = 0; u16 status; @@ -287,7 +282,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Wait until bus not busy */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return 1; /* Zero, one or two bytes reg address (offset) */ @@ -308,12 +303,12 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) #endif /* Send register offset */ while (1) { - status = wait_for_event(); + status = wait_for_event(adap); /* Try to identify bus that is not padconf'd for I2C */ if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_read (addr phase): pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto rd_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -348,7 +343,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) /* Receive data */ while (1) { - status = wait_for_event(); + status = wait_for_event(adap); /* * Try to identify bus that is not padconf'd for I2C. This * state could be left over from previous transactions if @@ -357,7 +352,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_read (data phase): pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto rd_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -375,15 +370,17 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) } rd_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); return i2c_error; } /* i2c_write: Address (reg offset) may be 0, 1 or 2 bytes long. */ -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int omap24_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c *i2c_base = omap24_get_base(adap); int i; u16 status; int i2c_error = 0; @@ -415,7 +412,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Wait until bus not busy */ - if (wait_for_bb()) + if (wait_for_bb(adap)) return 1; /* Start address phase - will write regoffset + len bytes data */ @@ -428,12 +425,12 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) while (alen) { /* Must write reg offset (one or two bytes) */ - status = wait_for_event(); + status = wait_for_event(adap); /* Try to identify bus that is not padconf'd for I2C */ if (status == I2C_STAT_XRDY) { i2c_error = 2; printf("i2c_write: pads on bus %d probably not configured (status=0x%x)\n", - current_bus, status); + adap->hwadapnr, status); goto wr_exit; } if (status == 0 || status & I2C_STAT_NACK) { @@ -455,7 +452,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Address phase is over, now write data */ for (i = 0; i < len; i++) { - status = wait_for_event(); + status = wait_for_event(adap); if (status == 0 || status & I2C_STAT_NACK) { i2c_error = 1; printf("i2c_write: error waiting for data ACK (status=0x%x)\n", @@ -474,7 +471,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) } wr_exit: - flush_fifo(); + flush_fifo(adap); writew(0xFFFF, &i2c_base->stat); writew(0, &i2c_base->cnt); return i2c_error; @@ -484,8 +481,9 @@ wr_exit: * Wait for the bus to be free by checking the Bus Busy (BB) * bit to become clear */ -static int wait_for_bb(void) +static int wait_for_bb(struct i2c_adapter *adap) { + struct i2c *i2c_base = omap24_get_base(adap); int timeout = I2C_TIMEOUT; u16 stat; @@ -514,8 +512,9 @@ static int wait_for_bb(void) * Wait for the I2C controller to complete current action * and update status */ -static u16 wait_for_event(void) +static u16 wait_for_event(struct i2c_adapter *adap) { + struct i2c *i2c_base = omap24_get_base(adap); u16 status; int timeout = I2C_TIMEOUT; @@ -540,7 +539,7 @@ static u16 wait_for_event(void) * not been configured for I2C, and/or pull-ups are missing. */ printf("Check if pads/pull-ups of bus %d are properly configured\n", - current_bus); + adap->hwadapnr); writew(0xFFFF, &i2c_base->stat); status = 0; } @@ -548,48 +547,93 @@ static u16 wait_for_event(void) return status; } -int i2c_set_bus_num(unsigned int bus) +static struct i2c *omap24_get_base(struct i2c_adapter *adap) { - if (bus >= I2C_BUS_MAX) { - printf("Bad bus: %x\n", bus); - return -1; - } - - switch (bus) { - default: - bus = 0; /* Fall through */ + switch (adap->hwadapnr) { case 0: - i2c_base = (struct i2c *)I2C_BASE1; + return (struct i2c *)I2C_BASE1; break; case 1: - i2c_base = (struct i2c *)I2C_BASE2; + return (struct i2c *)I2C_BASE2; break; #if (I2C_BUS_MAX > 2) case 2: - i2c_base = (struct i2c *)I2C_BASE3; + return (struct i2c *)I2C_BASE3; break; #if (I2C_BUS_MAX > 3) case 3: - i2c_base = (struct i2c *)I2C_BASE4; + return (struct i2c *)I2C_BASE4; break; #if (I2C_BUS_MAX > 4) case 4: - i2c_base = (struct i2c *)I2C_BASE5; + return (struct i2c *)I2C_BASE5; break; #endif #endif #endif + default: + printf("wrong hwadapnr: %d\n", adap->hwadapnr); + break; } + return NULL; +} - current_bus = bus; +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED1) +#define CONFIG_SYS_OMAP24_I2C_SPEED1 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE1) +#define CONFIG_SYS_OMAP24_I2C_SLAVE1 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif - if (!bus_initialized[current_bus]) - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +U_BOOT_I2C_ADAP_COMPLETE(omap24_0, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED, + CONFIG_SYS_OMAP24_I2C_SLAVE, + 0) +U_BOOT_I2C_ADAP_COMPLETE(omap24_1, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED1, + CONFIG_SYS_OMAP24_I2C_SLAVE1, + 1) +#if (I2C_BUS_MAX > 2) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED2) +#define CONFIG_SYS_OMAP24_I2C_SPEED2 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE2) +#define CONFIG_SYS_OMAP24_I2C_SLAVE2 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif - return 0; -} +U_BOOT_I2C_ADAP_COMPLETE(omap24_2, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED2, + CONFIG_SYS_OMAP24_I2C_SLAVE2, + 2) +#if (I2C_BUS_MAX > 3) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED3) +#define CONFIG_SYS_OMAP24_I2C_SPEED3 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE3) +#define CONFIG_SYS_OMAP24_I2C_SLAVE3 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif -int i2c_get_bus_num(void) -{ - return (int) current_bus; -} +U_BOOT_I2C_ADAP_COMPLETE(omap24_3, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED3, + CONFIG_SYS_OMAP24_I2C_SLAVE3, + 3) +#if (I2C_BUS_MAX > 4) +#if !defined(CONFIG_SYS_OMAP24_I2C_SPEED4) +#define CONFIG_SYS_OMAP24_I2C_SPEED4 CONFIG_SYS_OMAP24_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_OMAP24_I2C_SLAVE4) +#define CONFIG_SYS_OMAP24_I2C_SLAVE4 CONFIG_SYS_OMAP24_I2C_SLAVE +#endif + +U_BOOT_I2C_ADAP_COMPLETE(omap24_4, omap24_i2c_init, omap24_i2c_probe, + omap24_i2c_read, omap24_i2c_write, NULL, + CONFIG_SYS_OMAP24_I2C_SPEED4, + CONFIG_SYS_OMAP24_I2C_SLAVE4, + 4) +#endif +#endif +#endif diff --git a/drivers/i2c/sh_i2c.c b/drivers/i2c/sh_i2c.c index 808202c..cc19100 100644 --- a/drivers/i2c/sh_i2c.c +++ b/drivers/i2c/sh_i2c.c @@ -6,6 +6,7 @@ */ #include <common.h> +#include <i2c.h> #include <asm/io.h> DECLARE_GLOBAL_DATA_PTR; @@ -22,8 +23,6 @@ struct sh_i2c { }; #undef ureg -static struct sh_i2c *base; - /* ICCR */ #define SH_I2C_ICCR_ICE (1 << 7) #define SH_I2C_ICCR_RACK (1 << 6) @@ -43,202 +42,165 @@ static struct sh_i2c *base; #define SH_I2C_ICIC_ICCHB8 (1 << 6) #endif +static const struct sh_i2c *i2c_dev[CONFIG_SYS_I2C_SH_NUM_CONTROLLERS] = { + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE0, +#ifdef CONFIG_SYS_I2C_SH_BASE1 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE1, +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE2 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE2, +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE3 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE3, +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE4 + (struct sh_i2c *)CONFIG_SYS_I2C_SH_BASE4, +#endif +}; + static u16 iccl, icch; #define IRQ_WAIT 1000 -static void irq_dte(struct sh_i2c *base) +static void sh_irq_dte(struct sh_i2c *dev) { int i; - for (i = 0 ; i < IRQ_WAIT ; i++) { - if (SH_IC_DTE & readb(&base->icsr)) + for (i = 0; i < IRQ_WAIT; i++) { + if (SH_IC_DTE & readb(&dev->icsr)) break; udelay(10); } } -static int irq_dte_with_tack(struct sh_i2c *base) +static int sh_irq_dte_with_tack(struct sh_i2c *dev) { int i; - for (i = 0 ; i < IRQ_WAIT ; i++) { - if (SH_IC_DTE & readb(&base->icsr)) + for (i = 0; i < IRQ_WAIT; i++) { + if (SH_IC_DTE & readb(&dev->icsr)) break; - if (SH_IC_TACK & readb(&base->icsr)) + if (SH_IC_TACK & readb(&dev->icsr)) return -1; udelay(10); } return 0; } -static void irq_busy(struct sh_i2c *base) +static void sh_irq_busy(struct sh_i2c *dev) { int i; - for (i = 0 ; i < IRQ_WAIT ; i++) { - if (!(SH_IC_BUSY & readb(&base->icsr))) + for (i = 0; i < IRQ_WAIT; i++) { + if (!(SH_IC_BUSY & readb(&dev->icsr))) break; udelay(10); } } -static int i2c_set_addr(struct sh_i2c *base, u8 id, u8 reg, int stop) +static int sh_i2c_set_addr(struct sh_i2c *dev, u8 chip, u8 addr, int stop) { u8 icic = SH_IC_TACK; - clrbits_8(&base->iccr, SH_I2C_ICCR_ICE); - setbits_8(&base->iccr, SH_I2C_ICCR_ICE); + debug("%s: chip: %x, addr: %x iccl: %x, icch %x\n", + __func__, chip, addr, iccl, icch); + clrbits_8(&dev->iccr, SH_I2C_ICCR_ICE); + setbits_8(&dev->iccr, SH_I2C_ICCR_ICE); - writeb(iccl & 0xff, &base->iccl); - writeb(icch & 0xff, &base->icch); + writeb(iccl & 0xff, &dev->iccl); + writeb(icch & 0xff, &dev->icch); #ifdef CONFIG_SH_I2C_8BIT if (iccl > 0xff) icic |= SH_I2C_ICIC_ICCLB8; if (icch > 0xff) icic |= SH_I2C_ICIC_ICCHB8; #endif - writeb(icic, &base->icic); + writeb(icic, &dev->icic); - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &base->iccr); - irq_dte(base); + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &dev->iccr); + sh_irq_dte(dev); - clrbits_8(&base->icsr, SH_IC_TACK); - writeb(id << 1, &base->icdr); - if (irq_dte_with_tack(base) != 0) + clrbits_8(&dev->icsr, SH_IC_TACK); + writeb(chip << 1, &dev->icdr); + if (sh_irq_dte_with_tack(dev) != 0) return -1; - writeb(reg, &base->icdr); + writeb(addr, &dev->icdr); if (stop) - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS), &base->iccr); + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS), &dev->iccr); - if (irq_dte_with_tack(base) != 0) + if (sh_irq_dte_with_tack(dev) != 0) return -1; return 0; } -static void i2c_finish(struct sh_i2c *base) +static void sh_i2c_finish(struct sh_i2c *dev) { - writeb(0, &base->icsr); - clrbits_8(&base->iccr, SH_I2C_ICCR_ICE); + writeb(0, &dev->icsr); + clrbits_8(&dev->iccr, SH_I2C_ICCR_ICE); } -static int i2c_raw_write(struct sh_i2c *base, u8 id, u8 reg, u8 val) +static int +sh_i2c_raw_write(struct sh_i2c *dev, u8 chip, uint addr, u8 val) { int ret = -1; - if (i2c_set_addr(base, id, reg, 0) != 0) + if (sh_i2c_set_addr(dev, chip, addr, 0) != 0) goto exit0; udelay(10); - writeb(val, &base->icdr); - if (irq_dte_with_tack(base) != 0) + writeb(val, &dev->icdr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - writeb((SH_I2C_ICCR_ICE | SH_I2C_ICCR_RTS), &base->iccr); - if (irq_dte_with_tack(base) != 0) + writeb((SH_I2C_ICCR_ICE | SH_I2C_ICCR_RTS), &dev->iccr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - irq_busy(base); + sh_irq_busy(dev); ret = 0; + exit0: - i2c_finish(base); + sh_i2c_finish(dev); return ret; } -static int i2c_raw_read(struct sh_i2c *base, u8 id, u8 reg) +static int sh_i2c_raw_read(struct sh_i2c *dev, u8 chip, u8 addr) { int ret = -1; #if defined(CONFIG_SH73A0) - if (i2c_set_addr(base, id, reg, 0) != 0) + if (sh_i2c_set_addr(dev, chip, addr, 0) != 0) goto exit0; #else - if (i2c_set_addr(base, id, reg, 1) != 0) + if (sh_i2c_set_addr(dev, chip, addr, 1) != 0) goto exit0; udelay(100); #endif - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &base->iccr); - irq_dte(base); + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RTS|SH_I2C_ICCR_BUSY), &dev->iccr); + sh_irq_dte(dev); - writeb(id << 1 | 0x01, &base->icdr); - if (irq_dte_with_tack(base) != 0) + writeb(chip << 1 | 0x01, &dev->icdr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_SCP), &base->iccr); - if (irq_dte_with_tack(base) != 0) + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_SCP), &dev->iccr); + if (sh_irq_dte_with_tack(dev) != 0) goto exit0; - ret = readb(&base->icdr) & 0xff; + ret = readb(&dev->icdr) & 0xff; + + writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RACK), &dev->iccr); + readb(&dev->icdr); /* Dummy read */ + sh_irq_busy(dev); - writeb((SH_I2C_ICCR_ICE|SH_I2C_ICCR_RACK), &base->iccr); - readb(&base->icdr); /* Dummy read */ - irq_busy(base); exit0: - i2c_finish(base); + sh_i2c_finish(dev); return ret; } -#ifdef CONFIG_I2C_MULTI_BUS -static unsigned int current_bus; - -/** - * i2c_set_bus_num - change active I2C bus - * @bus: bus index, zero based - * @returns: 0 on success, non-0 on failure - */ -int i2c_set_bus_num(unsigned int bus) -{ - if ((bus < 0) || (bus >= CONFIG_SYS_MAX_I2C_BUS)) { - printf("Bad bus: %d\n", bus); - return -1; - } - - switch (bus) { - case 0: - base = (void *)CONFIG_SH_I2C_BASE0; - break; - case 1: - base = (void *)CONFIG_SH_I2C_BASE1; - break; -#ifdef CONFIG_SH_I2C_BASE2 - case 2: - base = (void *)CONFIG_SH_I2C_BASE2; - break; -#endif -#ifdef CONFIG_SH_I2C_BASE3 - case 3: - base = (void *)CONFIG_SH_I2C_BASE3; - break; -#endif -#ifdef CONFIG_SH_I2C_BASE4 - case 4: - base = (void *)CONFIG_SH_I2C_BASE4; - break; -#endif - default: - return -1; - } - current_bus = bus; - - return 0; -} - -/** - * i2c_get_bus_num - returns index of active I2C bus - */ -unsigned int i2c_get_bus_num(void) -{ - return current_bus; -} -#endif - -#define SH_I2C_ICCL_CALC(clk, date, t_low, t_high) \ - ((clk / rate) * (t_low / t_low + t_high)) -#define SH_I2C_ICCH_CALC(clk, date, t_low, t_high) \ - ((clk / rate) * (t_high / t_low + t_high)) - -void i2c_init(int speed, int slaveaddr) +static void +sh_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { int num, denom, tmp; @@ -246,11 +208,6 @@ void i2c_init(int speed, int slaveaddr) if (!(gd->flags & GD_FLG_RELOC)) return; -#ifdef CONFIG_I2C_MULTI_BUS - current_bus = 0; -#endif - base = (struct sh_i2c *)CONFIG_SH_I2C_BASE0; - /* * Calculate the value for iccl. From the data sheet: * iccl = (p-clock / transfer-rate) * (L / (L + H)) @@ -272,67 +229,78 @@ void i2c_init(int speed, int slaveaddr) icch = (u16)((num/denom) + 1); else icch = (u16)(num/denom); + + debug("clock: %d, speed %d, iccl: %x, icch: %x\n", + CONFIG_SH_I2C_CLOCK, speed, iccl, icch); } -/* - * i2c_read: - Read multiple bytes from an i2c device - * - * The higher level routines take into account that this function is only - * called with len < page length of the device (see configuration file) - * - * @chip: address of the chip which is to be read - * @addr: i2c data address within the chip - * @alen: length of the i2c data address (1..2 bytes) - * @buffer: where to write the data - * @len: how much byte do we want to read - * @return: 0 in case of success - */ -int i2c_read(u8 chip, u32 addr, int alen, u8 *buffer, int len) +static int sh_i2c_read(struct i2c_adapter *adap, uint8_t chip, + uint addr, int alen, u8 *data, int len) { - int ret; - int i = 0; - for (i = 0 ; i < len ; i++) { - ret = i2c_raw_read(base, chip, addr + i); + int ret, i; + struct sh_i2c *dev = (struct sh_i2c *)i2c_dev[adap->hwadapnr]; + + for (i = 0; i < len; i++) { + ret = sh_i2c_raw_read(dev, chip, addr + i); if (ret < 0) return -1; - buffer[i] = ret & 0xff; + + data[i] = ret & 0xff; + debug("%s: data[%d]: %02x\n", __func__, i, data[i]); } + return 0; } -/* - * i2c_write: - Write multiple bytes to an i2c device - * - * The higher level routines take into account that this function is only - * called with len < page length of the device (see configuration file) - * - * @chip: address of the chip which is to be written - * @addr: i2c data address within the chip - * @alen: length of the i2c data address (1..2 bytes) - * @buffer: where to find the data to be written - * @len: how much byte do we want to read - * @return: 0 in case of success - */ -int i2c_write(u8 chip, u32 addr, int alen, u8 *buffer, int len) +static int sh_i2c_write(struct i2c_adapter *adap, uint8_t chip, uint addr, + int alen, u8 *data, int len) { - int i = 0; - for (i = 0; i < len ; i++) - if (i2c_raw_write(base, chip, addr + i, buffer[i]) != 0) + struct sh_i2c *dev = (struct sh_i2c *)i2c_dev[adap->hwadapnr]; + int i; + + for (i = 0; i < len; i++) { + debug("%s: data[%d]: %02x\n", __func__, i, data[i]); + if (sh_i2c_raw_write(dev, chip, addr + i, data[i]) != 0) return -1; + } return 0; } -/* - * i2c_probe: - Test if a chip answers for a given i2c address - * - * @chip: address of the chip which is searched for - * @return: 0 if a chip was found, -1 otherwhise - */ -int i2c_probe(u8 chip) +static int +sh_i2c_probe(struct i2c_adapter *adap, u8 dev) { - int ret; + return sh_i2c_read(adap, dev, 0, 0, NULL, 0); +} - ret = i2c_set_addr(base, chip, 0, 1); - i2c_finish(base); - return ret; +static unsigned int sh_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) +{ + struct sh_i2c *dev = (struct sh_i2c *)i2c_dev[adap->hwadapnr]; + + sh_i2c_finish(dev); + sh_i2c_init(adap, speed, 0); + + return 0; } + +/* + * Register RCAR i2c adapters + */ +U_BOOT_I2C_ADAP_COMPLETE(sh_0, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED0, 0, 0) +#ifdef CONFIG_SYS_I2C_SH_BASE1 +U_BOOT_I2C_ADAP_COMPLETE(sh_1, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED1, 0, 1) +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE2 +U_BOOT_I2C_ADAP_COMPLETE(sh_2, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED2, 0, 2) +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE3 +U_BOOT_I2C_ADAP_COMPLETE(sh_3, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED3, 0, 3) +#endif +#ifdef CONFIG_SYS_I2C_SH_BASE4 +U_BOOT_I2C_ADAP_COMPLETE(sh_4, sh_i2c_init, sh_i2c_probe, sh_i2c_read, + sh_i2c_write, sh_i2c_set_bus_speed, CONFIG_SYS_I2C_SH_SPEED4, 0, 4) +#endif diff --git a/drivers/i2c/zynq_i2c.c b/drivers/i2c/zynq_i2c.c index ce2d23f..70a9aea 100644 --- a/drivers/i2c/zynq_i2c.c +++ b/drivers/i2c/zynq_i2c.c @@ -74,7 +74,8 @@ static struct zynq_i2c_registers *zynq_i2c = (struct zynq_i2c_registers *)ZYNQ_I2C_BASE; /* I2C init called by cmd_i2c when doing 'i2c reset'. */ -void i2c_init(int requested_speed, int slaveadd) +static void zynq_i2c_init(struct i2c_adapter *adap, int requested_speed, + int slaveadd) { /* 111MHz / ( (3 * 17) * 22 ) = ~100KHz */ writel((16 << ZYNQ_I2C_CONTROL_DIV_B_SHIFT) | @@ -151,7 +152,7 @@ static u32 zynq_i2c_wait(u32 mask) * I2C probe called by cmd_i2c when doing 'i2c probe'. * Begin read, nak data byte, end. */ -int i2c_probe(u8 dev) +static int zynq_i2c_probe(struct i2c_adapter *adap, u8 dev) { /* Attempt to read a byte */ setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO | @@ -170,7 +171,8 @@ int i2c_probe(u8 dev) * I2C read called by cmd_i2c when doing 'i2c read' and by cmd_eeprom.c * Begin write, send address byte(s), begin read, receive data bytes, end. */ -int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) +static int zynq_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, + int alen, u8 *data, int length) { u32 status; u32 i = 0; @@ -235,7 +237,8 @@ int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) * I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c * Begin write, send address byte(s), send data bytes, end. */ -int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) +static int zynq_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, + int alen, u8 *data, int length) { u8 *cur_data = data; @@ -275,16 +278,16 @@ int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) return 0; } -int i2c_set_bus_num(unsigned int bus) +static unsigned int zynq_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) { - /* Only support bus 0 */ - if (bus > 0) - return -1; - return 0; -} + if (speed != 1000000) + return -EINVAL; -unsigned int i2c_get_bus_num(void) -{ - /* Only support bus 0 */ return 0; } + +U_BOOT_I2C_ADAP_COMPLETE(zynq_0, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read, + zynq_i2c_write, zynq_i2c_set_bus_speed, + CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE, + 0) diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile index bec86c1..d0fd7fc 100644 --- a/drivers/net/fm/Makefile +++ b/drivers/net/fm/Makefile @@ -4,7 +4,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifdef CONFIG_FMAN_ENET obj-y += dtsec.o obj-y += eth.o obj-y += fm.o @@ -26,8 +25,10 @@ obj-$(CONFIG_PPC_P4080) += p4080.o obj-$(CONFIG_PPC_P5020) += p5020.o obj-$(CONFIG_PPC_P5040) += p5040.o obj-$(CONFIG_PPC_T1040) += t1040.o +obj-$(CONFIG_PPC_T1042) += t1040.o +obj-$(CONFIG_PPC_T1020) += t1040.o +obj-$(CONFIG_PPC_T1022) += t1040.o obj-$(CONFIG_PPC_T4240) += t4240.o obj-$(CONFIG_PPC_T4160) += t4240.o obj-$(CONFIG_PPC_B4420) += b4860.o obj-$(CONFIG_PPC_B4860) += b4860.o -endif diff --git a/drivers/net/npe/Makefile b/drivers/net/npe/Makefile index 7fa5ea6..e36c0bb 100644 --- a/drivers/net/npe/Makefile +++ b/drivers/net/npe/Makefile @@ -10,7 +10,7 @@ CFLAGS += $(LOCAL_CFLAGS) CPPFLAGS += $(LOCAL_CFLAGS) # needed for depend HOSTCFLAGS += $(LOCAL_CFLAGS) -obj-$(CONFIG_IXP4XX_NPE) := npe.o \ +obj-y := npe.o \ miiphy.o \ IxOsalBufferMgt.o \ IxOsalIoMem.o \ diff --git a/drivers/qe/Makefile b/drivers/qe/Makefile index b8c15f8..7f1bd06 100644 --- a/drivers/qe/Makefile +++ b/drivers/qe/Makefile @@ -4,5 +4,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(and $(CONFIG_QE),$(CONFIG_OF_LIBFDT)) += fdt.o -obj-$(CONFIG_QE) += qe.o uccf.o uec.o uec_phy.o +obj-y := qe.o uccf.o uec.o uec_phy.o +obj-$(CONFIG_OF_LIBFDT) += fdt.o diff --git a/drivers/tpm/Makefile b/drivers/tpm/Makefile index 4b8cbec..2f2353f 100644 --- a/drivers/tpm/Makefile +++ b/drivers/tpm/Makefile @@ -3,8 +3,6 @@ # SPDX-License-Identifier: GPL-2.0+ # -$(shell mkdir -p $(obj)slb9635_i2c) - # TODO: Merge tpm_tis_lpc.c with tpm.c obj-$(CONFIG_TPM_ATMEL_TWI) += tpm_atmel_twi.o obj-$(CONFIG_TPM_TIS_I2C) += tpm.o diff --git a/drivers/tpm/tis_i2c.c b/drivers/tpm/tis_i2c.c deleted file mode 100644 index 22554e1..0000000 --- a/drivers/tpm/tis_i2c.c +++ /dev/null @@ -1,185 +0,0 @@ -/* - * Copyright (c) 2012 The Chromium OS Authors. All rights reserved. - * Use of this source code is governed by a BSD-style license that can be - * found in the LICENSE file. - */ - -#include <config.h> -#include <common.h> -#include <fdtdec.h> -#include <i2c.h> -#include "slb9635_i2c/tpm.h" - -DECLARE_GLOBAL_DATA_PTR; - -/* TPM configuration */ -struct tpm { - int i2c_bus; - int slave_addr; - char inited; - int old_bus; -} tpm; - - -static int tpm_select(void) -{ - int ret; - - tpm.old_bus = i2c_get_bus_num(); - if (tpm.old_bus != tpm.i2c_bus) { - ret = i2c_set_bus_num(tpm.i2c_bus); - if (ret) { - debug("%s: Fail to set i2c bus %d\n", __func__, - tpm.i2c_bus); - return -1; - } - } - return 0; -} - -static int tpm_deselect(void) -{ - int ret; - - if (tpm.old_bus != i2c_get_bus_num()) { - ret = i2c_set_bus_num(tpm.old_bus); - if (ret) { - debug("%s: Fail to restore i2c bus %d\n", - __func__, tpm.old_bus); - return -1; - } - } - tpm.old_bus = -1; - return 0; -} - -/** - * Decode TPM configuration. - * - * @param dev Returns a configuration of TPM device - * @return 0 if ok, -1 on error - */ -static int tpm_decode_config(struct tpm *dev) -{ -#ifdef CONFIG_OF_CONTROL - const void *blob = gd->fdt_blob; - int node, parent; - int i2c_bus; - - node = fdtdec_next_compatible(blob, 0, COMPAT_INFINEON_SLB9635_TPM); - if (node < 0) { - node = fdtdec_next_compatible(blob, 0, - COMPAT_INFINEON_SLB9645_TPM); - } - if (node < 0) { - debug("%s: Node not found\n", __func__); - return -1; - } - parent = fdt_parent_offset(blob, node); - if (parent < 0) { - debug("%s: Cannot find node parent\n", __func__); - return -1; - } - i2c_bus = i2c_get_bus_num_fdt(parent); - if (i2c_bus < 0) - return -1; - dev->i2c_bus = i2c_bus; - dev->slave_addr = fdtdec_get_addr(blob, node, "reg"); -#else - dev->i2c_bus = CONFIG_INFINEON_TPM_I2C_BUS; - dev->slave_addr = CONFIG_INFINEON_TPM_I2C_ADDR; -#endif - return 0; -} - -int tis_init(void) -{ - if (tpm.inited) - return 0; - - if (tpm_decode_config(&tpm)) - return -1; - - if (tpm_select()) - return -1; - - /* - * Probe TPM twice; the first probing might fail because TPM is asleep, - * and the probing can wake up TPM. - */ - if (i2c_probe(tpm.slave_addr) && i2c_probe(tpm.slave_addr)) { - debug("%s: fail to probe i2c addr 0x%x\n", __func__, - tpm.slave_addr); - return -1; - } - - tpm_deselect(); - - tpm.inited = 1; - - return 0; -} - -int tis_open(void) -{ - int rc; - - if (!tpm.inited) - return -1; - - if (tpm_select()) - return -1; - - rc = tpm_open(tpm.slave_addr); - - tpm_deselect(); - - return rc; -} - -int tis_close(void) -{ - if (!tpm.inited) - return -1; - - if (tpm_select()) - return -1; - - tpm_close(); - - tpm_deselect(); - - return 0; -} - -int tis_sendrecv(const uint8_t *sendbuf, size_t sbuf_size, - uint8_t *recvbuf, size_t *rbuf_len) -{ - int len; - uint8_t buf[4096]; - - if (!tpm.inited) - return -1; - - if (sizeof(buf) < sbuf_size) - return -1; - - memcpy(buf, sendbuf, sbuf_size); - - if (tpm_select()) - return -1; - - len = tpm_transmit(buf, sbuf_size); - - tpm_deselect(); - - if (len < 10) { - *rbuf_len = 0; - return -1; - } - - memcpy(recvbuf, buf, len); - *rbuf_len = len; - - return 0; -} diff --git a/examples/standalone/Makefile b/examples/standalone/Makefile index 4afedea..9346921 100644 --- a/examples/standalone/Makefile +++ b/examples/standalone/Makefile @@ -8,7 +8,6 @@ include $(TOPDIR)/config.mk ELF-$(ARCH) := -ELF-$(BOARD) := ELF-$(CPU) := ELF-y := hello_world @@ -20,14 +19,13 @@ ELF-mpc5xxx += interrupt ELF-mpc8xx += test_burst timer ELF-mpc8260 += mem_to_mem_idma2intr ELF-ppc += sched -ELF-oxc += eepro100_eeprom # # Some versions of make do not handle trailing white spaces properly; # leading to build failures. The problem was found with GNU Make 3.80. # Using 'strip' as a workaround for the problem. # -ELF := $(strip $(ELF-y) $(ELF-$(ARCH)) $(ELF-$(BOARD)) $(ELF-$(CPU))) +ELF := $(strip $(ELF-y) $(ELF-$(ARCH)) $(ELF-$(CPU))) SREC := $(addsuffix .srec,$(ELF)) BIN := $(addsuffix .bin,$(ELF)) diff --git a/examples/standalone/eepro100_eeprom.c b/examples/standalone/eepro100_eeprom.c deleted file mode 100644 index 3c7f380..0000000 --- a/examples/standalone/eepro100_eeprom.c +++ /dev/null @@ -1,214 +0,0 @@ -/* - * Copyright 1998-2001 by Donald Becker. - * This software may be used and distributed according to the terms of - * the GNU General Public License (GPL), incorporated herein by reference. - * Contact the author for use under other terms. - * - * This program must be compiled with "-O"! - * See the bottom of this file for the suggested compile-command. - * - * The author may be reached as becker@scyld.com, or C/O - * Scyld Computing Corporation - * 410 Severn Ave., Suite 210 - * Annapolis MD 21403 - * - * Common-sense licensing statement: Using any portion of this program in - * your own program means that you must give credit to the original author - * and release the resulting code under the GPL. - */ - -/* avoid unnecessary memcpy function */ -#define _PPC_STRING_H_ - -#include <common.h> -#include <exports.h> - -static int reset_eeprom(unsigned long ioaddr, unsigned char *hwaddr); - -int eepro100_eeprom(int argc, char * const argv[]) -{ - int ret = 0; - - unsigned char hwaddr1[6] = { 0x00, 0x00, 0x02, 0x03, 0x04, 0x05 }; - unsigned char hwaddr2[6] = { 0x00, 0x00, 0x02, 0x03, 0x04, 0x06 }; - - app_startup(argv); - -#if defined(CONFIG_OXC) - ret |= reset_eeprom(0x80000000, hwaddr1); - ret |= reset_eeprom(0x81000000, hwaddr2); -#endif - - return ret; -} - -/* Default EEPROM for i82559 */ -static unsigned short default_eeprom[64] = { - 0x0100, 0x0302, 0x0504, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, - 0xffff, 0xffff, 0x40c0, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, - 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, - 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, - 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, - 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, - 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, - 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff -}; - -static unsigned short eeprom[256]; - -static int eeprom_size = 64; -static int eeprom_addr_size = 6; - -static int debug = 0; - -static inline unsigned short swap16(unsigned short x) -{ - return (((x & 0xff) << 8) | ((x & 0xff00) >> 8)); -} - -static inline void outw(short data, long addr) -{ - *(volatile short *)(addr) = swap16(data); -} - -static inline short inw(long addr) -{ - return swap16(*(volatile short *)(addr)); -} - -void *memcpy(void *dst, const void *src, unsigned int len) -{ - char *ret = dst; - while (len-- > 0) { - *ret++ = *((char *)src); - src++; - } - return (void *)ret; -} - -/* The EEPROM commands include the alway-set leading bit. */ -#define EE_WRITE_CMD (5) -#define EE_READ_CMD (6) -#define EE_ERASE_CMD (7) - -/* Serial EEPROM section. */ -#define EE_SHIFT_CLK 0x01 /* EEPROM shift clock. */ -#define EE_CS 0x02 /* EEPROM chip select. */ -#define EE_DATA_WRITE 0x04 /* EEPROM chip data in. */ -#define EE_DATA_READ 0x08 /* EEPROM chip data out. */ -#define EE_ENB (0x4800 | EE_CS) -#define EE_WRITE_0 0x4802 -#define EE_WRITE_1 0x4806 -#define EE_OFFSET 14 - -/* Delay between EEPROM clock transitions. */ -#define eeprom_delay(ee_addr) inw(ee_addr) - -/* Wait for the EEPROM to finish the previous operation. */ -static int eeprom_busy_poll(long ee_ioaddr) -{ - int i; - outw(EE_ENB, ee_ioaddr); - for (i = 0; i < 10000; i++) /* Typical 2000 ticks */ - if (inw(ee_ioaddr) & EE_DATA_READ) - break; - return i; -} - -/* This executes a generic EEPROM command, typically a write or write enable. - It returns the data output from the EEPROM, and thus may also be used for - reads. */ -static int do_eeprom_cmd(long ioaddr, int cmd, int cmd_len) -{ - unsigned retval = 0; - long ee_addr = ioaddr + EE_OFFSET; - - if (debug > 1) - printf(" EEPROM op 0x%x: ", cmd); - - outw(EE_ENB | EE_SHIFT_CLK, ee_addr); - - /* Shift the command bits out. */ - do { - short dataval = (cmd & (1 << cmd_len)) ? EE_WRITE_1 : EE_WRITE_0; - outw(dataval, ee_addr); - eeprom_delay(ee_addr); - if (debug > 2) - printf("%X", inw(ee_addr) & 15); - outw(dataval | EE_SHIFT_CLK, ee_addr); - eeprom_delay(ee_addr); - retval = (retval << 1) | ((inw(ee_addr) & EE_DATA_READ) ? 1 : 0); - } while (--cmd_len >= 0); -#if 0 - outw(EE_ENB, ee_addr); -#endif - /* Terminate the EEPROM access. */ - outw(EE_ENB & ~EE_CS, ee_addr); - if (debug > 1) - printf(" EEPROM result is 0x%5.5x.\n", retval); - return retval; -} - -static int read_eeprom(long ioaddr, int location, int addr_len) -{ - return do_eeprom_cmd(ioaddr, ((EE_READ_CMD << addr_len) | location) - << 16 , 3 + addr_len + 16) & 0xffff; -} - -static void write_eeprom(long ioaddr, int index, int value, int addr_len) -{ - long ee_ioaddr = ioaddr + EE_OFFSET; - int i; - - /* Poll for previous op finished. */ - eeprom_busy_poll(ee_ioaddr); /* Typical 0 ticks */ - /* Enable programming modes. */ - do_eeprom_cmd(ioaddr, (0x4f << (addr_len-4)), 3 + addr_len); - /* Do the actual write. */ - do_eeprom_cmd(ioaddr, - (((EE_WRITE_CMD<<addr_len) | index)<<16) | (value & 0xffff), - 3 + addr_len + 16); - /* Poll for write finished. */ - i = eeprom_busy_poll(ee_ioaddr); /* Typical 2000 ticks */ - if (debug) - printf(" Write finished after %d ticks.\n", i); - /* Disable programming. This command is not instantaneous, so we check - for busy before the next op. */ - do_eeprom_cmd(ioaddr, (0x40 << (addr_len-4)), 3 + addr_len); - eeprom_busy_poll(ee_ioaddr); -} - -static int reset_eeprom(unsigned long ioaddr, unsigned char *hwaddr) -{ - unsigned short checksum = 0; - int size_test; - int i; - - printf("Resetting i82559 EEPROM @ 0x%08lX ... ", ioaddr); - - size_test = do_eeprom_cmd(ioaddr, (EE_READ_CMD << 8) << 16, 27); - eeprom_addr_size = (size_test & 0xffe0000) == 0xffe0000 ? 8 : 6; - eeprom_size = 1 << eeprom_addr_size; - - memcpy(eeprom, default_eeprom, sizeof default_eeprom); - - for (i = 0; i < 3; i++) - eeprom[i] = (hwaddr[i*2+1]<<8) + hwaddr[i*2]; - - /* Recalculate the checksum. */ - for (i = 0; i < eeprom_size - 1; i++) - checksum += eeprom[i]; - eeprom[i] = 0xBABA - checksum; - - for (i = 0; i < eeprom_size; i++) - write_eeprom(ioaddr, i, eeprom[i], eeprom_addr_size); - - for (i = 0; i < eeprom_size; i++) - if (read_eeprom(ioaddr, i, eeprom_addr_size) != eeprom[i]) { - printf("failed\n"); - return 1; - } - - printf("done\n"); - return 0; -} diff --git a/fs/Makefile b/fs/Makefile index bdcd746..34dc035 100644 --- a/fs/Makefile +++ b/fs/Makefile @@ -6,15 +6,20 @@ # SPDX-License-Identifier: GPL-2.0+ # +ifdef CONFIG_SPL_BUILD +obj-$(CONFIG_SPL_FAT_SUPPORT) += fat/ +else obj-y += fs.o -obj-y += cbfs/ -obj-y += cramfs/ -obj-y += ext4/ -obj-y += fdos/ -obj-y += jffs2/ -obj-y += reiserfs/ -obj-y += sandbox/ -obj-y += ubifs/ -obj-y += yaffs2/ -obj-y += zfs/ +obj-$(CONFIG_CMD_CBFS) += cbfs/ +obj-$(CONFIG_CMD_CRAMFS) += cramfs/ +obj-$(CONFIG_FS_EXT4) += ext4/ +obj-y += fat/ +obj-$(CONFIG_CMD_FDOS) += fdos/ +obj-$(CONFIG_CMD_JFFS2) += jffs2/ +obj-$(CONFIG_CMD_REISER) += reiserfs/ +obj-$(CONFIG_SANDBOX) += sandbox/ +obj-$(CONFIG_CMD_UBIFS) += ubifs/ +obj-$(CONFIG_YAFFS2) += yaffs2/ +obj-$(CONFIG_CMD_ZFS) += zfs/ +endif diff --git a/fs/cbfs/Makefile b/fs/cbfs/Makefile index 6f33d28..a106e05 100644 --- a/fs/cbfs/Makefile +++ b/fs/cbfs/Makefile @@ -3,4 +3,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_CMD_CBFS) := cbfs.o +obj-y := cbfs.o diff --git a/fs/cramfs/Makefile b/fs/cramfs/Makefile index e2b2c73..12d73a3 100644 --- a/fs/cramfs/Makefile +++ b/fs/cramfs/Makefile @@ -5,5 +5,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_CMD_CRAMFS) := cramfs.o -obj-$(CONFIG_CMD_CRAMFS) += uncompress.o +obj-y := cramfs.o +obj-y += uncompress.o diff --git a/fs/ext4/Makefile b/fs/ext4/Makefile index 0f5d399..8d15bda 100644 --- a/fs/ext4/Makefile +++ b/fs/ext4/Makefile @@ -9,5 +9,5 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_FS_EXT4) := ext4fs.o ext4_common.o dev.o +obj-y := ext4fs.o ext4_common.o dev.o obj-$(CONFIG_EXT4_WRITE) += ext4_write.o ext4_journal.o crc16.o diff --git a/fs/fdos/Makefile b/fs/fdos/Makefile index 95480af..2f8b5ad 100644 --- a/fs/fdos/Makefile +++ b/fs/fdos/Makefile @@ -10,4 +10,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_CMD_FDOS) := fat.o vfat.o dev.o fdos.o fs.o subdir.o +obj-y := fat.o vfat.o dev.o fdos.o fs.o subdir.o diff --git a/fs/jffs2/Makefile b/fs/jffs2/Makefile index 02e481f..4cb0600 100644 --- a/fs/jffs2/Makefile +++ b/fs/jffs2/Makefile @@ -5,11 +5,9 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifdef CONFIG_CMD_JFFS2 obj-$(CONFIG_JFFS2_LZO) += compr_lzo.o obj-y += compr_rtime.o obj-y += compr_rubin.o obj-y += compr_zlib.o obj-y += jffs2_1pass.o obj-y += mini_inflate.o -endif diff --git a/fs/reiserfs/Makefile b/fs/reiserfs/Makefile index 55f70b1..5a692f0 100644 --- a/fs/reiserfs/Makefile +++ b/fs/reiserfs/Makefile @@ -9,4 +9,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_CMD_REISER) := reiserfs.o dev.o mode_string.o +obj-y := reiserfs.o dev.o mode_string.o diff --git a/fs/sandbox/Makefile b/fs/sandbox/Makefile index faa7c16..ca238f6 100644 --- a/fs/sandbox/Makefile +++ b/fs/sandbox/Makefile @@ -10,4 +10,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_SANDBOX) := sandboxfs.o +obj-y := sandboxfs.o diff --git a/fs/ubifs/Makefile b/fs/ubifs/Makefile index 47d5a8f..389b0e3 100644 --- a/fs/ubifs/Makefile +++ b/fs/ubifs/Makefile @@ -9,10 +9,10 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_CMD_UBIFS) := ubifs.o io.o super.o sb.o master.o lpt.o -obj-$(CONFIG_CMD_UBIFS) += lpt_commit.o scan.o lprops.o -obj-$(CONFIG_CMD_UBIFS) += tnc.o tnc_misc.o debug.o crc16.o budget.o -obj-$(CONFIG_CMD_UBIFS) += log.o orphan.o recovery.o replay.o +obj-y := ubifs.o io.o super.o sb.o master.o lpt.o +obj-y += lpt_commit.o scan.o lprops.o +obj-y += tnc.o tnc_misc.o debug.o crc16.o budget.o +obj-y += log.o orphan.o recovery.o replay.o # SEE README.arm-unaligned-accesses $(obj)super.o: CFLAGS += $(PLATFORM_NO_UNALIGNED) diff --git a/fs/yaffs2/Makefile b/fs/yaffs2/Makefile index 077af78..d811287 100644 --- a/fs/yaffs2/Makefile +++ b/fs/yaffs2/Makefile @@ -16,7 +16,7 @@ # # $Id: Makefile,v 1.15 2007/07/18 19:40:38 charles Exp $ -obj-$(CONFIG_YAFFS2) := \ +obj-y := \ yaffs_allocator.o yaffs_attribs.o yaffs_bitmap.o yaffs_uboot_glue.o\ yaffs_checkptrw.o yaffs_ecc.o yaffs_error.o \ yaffsfs.o yaffs_guts.o yaffs_nameval.o yaffs_nand.o\ diff --git a/fs/zfs/Makefile b/fs/zfs/Makefile index 7090416..fa58b7f 100644 --- a/fs/zfs/Makefile +++ b/fs/zfs/Makefile @@ -5,4 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_CMD_ZFS) := dev.o zfs.o zfs_fletcher.o zfs_sha256.o zfs_lzjb.o +obj-y := dev.o zfs.o zfs_fletcher.o zfs_sha256.o zfs_lzjb.o diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index 2738242..7c6bec8 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -32,6 +32,8 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_pbi.cfg +#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_rcw.cfg #endif /* High Level Configuration Options */ diff --git a/include/configs/T1040RDB.h b/include/configs/T1040RDB.h new file mode 100644 index 0000000..620387f --- /dev/null +++ b/include/configs/T1040RDB.h @@ -0,0 +1,690 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * T1040 RDB board configuration file + */ +#define CONFIG_T104xRDB +#define CONFIG_T1040RDB +#define CONFIG_PHYS_64BIT + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_MP /* support multiple processors */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_PCIE4 /* PCIE controler 4 */ + +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#ifndef CONFIG_SYS_NO_FLASH +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1105) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif +#else /* CONFIG_SYS_NO_FLASH */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#define CONFIG_SYS_CLK_FREQ 100000000 +#define CONFIG_DDR_CLK_FREQ 66666666 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_SYS_DDR_RAW_TIMING +#define CONFIG_FSL_DDR3 + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x51 + +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe8000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) + +#define CONFIG_SYS_NOR_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} + +/* CPLD on IFC */ +#define CONFIG_SYS_CPLD_BASE 0xffdf0000 +#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) +#define CONFIG_SYS_CSOR2 0x0 +/* CPLD Timing parameters for IFC CS2 */ +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS2_FTIM3 0x0 + +/* NAND Flash on IFC */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ + | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ + | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 + +/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR 0x70 +#define I2C_MUX_CH_DEFAULT 0x8 + + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +#ifdef CONFIG_PCI +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#ifdef CONFIG_PCIE1 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#ifdef CONFIG_PCIE2 +#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#ifdef CONFIG_PCIE3 +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 4, Base address 203000 */ +#ifdef CONFIG_PCIE4 +#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000 +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ +#endif + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#define CONFIG_FSL_SATA_V2 +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +/* +* USB +*/ +#define CONFIG_HAS_FSL_DR_USB + +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#endif +#endif + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 25 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 25 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 545KB (1089 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_REALTEK +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c +#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d +#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e +#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /*-1 disables auto-boot*/ + +#define CONFIG_BAUDRATE 115200 + +#define __USB_PHY_TYPE utmi + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ + "bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=t1040rdb/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=t1040rdb/t1040rdb.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#ifdef CONFIG_SECURE_BOOT +#include <asm/fsl_secure_boot.h> +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h new file mode 100644 index 0000000..4b023f9 --- /dev/null +++ b/include/configs/T1042RDB_PI.h @@ -0,0 +1,694 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * T1042RDB_PI board configuration file + */ +#define CONFIG_T104xRDB +#define CONFIG_T1042RDB_PI +#define CONFIG_PHYS_64BIT + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_MP /* support multiple processors */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_PCIE4 /* PCIE controler 4 */ + +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#ifndef CONFIG_SYS_NO_FLASH +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1105) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif +#else /* CONFIG_SYS_NO_FLASH */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#define CONFIG_SYS_CLK_FREQ 100000000 +#define CONFIG_DDR_CLK_FREQ 66666666 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_SYS_DDR_RAW_TIMING +#define CONFIG_FSL_DDR3 + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x51 + +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe8000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) + +#define CONFIG_SYS_NOR_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} + +/* CPLD on IFC */ +#define CONFIG_SYS_CPLD_BASE 0xffdf0000 +#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) +#define CONFIG_SYS_CSOR2 0x0 +/* CPLD Timing parameters for IFC CS2 */ +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS2_FTIM3 0x0 + +/* NAND Flash on IFC */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ + | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ + | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 + +/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR 0x70 + +/* + * RTC configuration + */ +#define RTC +#define CONFIG_RTC_DS1337 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/*DVI encoder*/ +#define CONFIG_HDMI_ENCODER_I2C_ADDR 0x75 + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +#ifdef CONFIG_PCI +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#ifdef CONFIG_PCIE1 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#ifdef CONFIG_PCIE2 +#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#ifdef CONFIG_PCIE3 +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ +#endif + +/* controller 4, Base address 203000 */ +#ifdef CONFIG_PCIE4 +#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000 +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ +#endif + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* SATA */ +#define CONFIG_FSL_SATA_V2 +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA + +#define CONFIG_SYS_SATA_MAX_DEVICE 1 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA + +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +/* +* USB +*/ +#define CONFIG_HAS_FSL_DR_USB + +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#endif +#endif + +#define CONFIG_MMC + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 25 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 25 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 545KB (1089 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHY_VITESSE +#define CONFIG_PHY_REALTEK +#endif + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SETEXPR + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /*-1 disables auto-boot*/ + +#define CONFIG_BAUDRATE 115200 + +#define __USB_PHY_TYPE utmi + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ + "bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=t1040rdb_pi/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=t1040rdb_pi/t1040rdb_pi.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#ifdef CONFIG_SECURE_BOOT +#include <asm/fsl_secure_boot.h> +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index c2ba7e3..f35ed6f 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -183,7 +183,6 @@ #define CONFIG_SYS_NS16550_COM6 0x481aa000 /* UART5 */ #define CONFIG_BAUDRATE 115200 -/* I2C Configuration */ #define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */ diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h index c5e67bf..6fd3fb9 100644 --- a/include/configs/am3517_crane.h +++ b/include/configs/am3517_crane.h @@ -142,10 +142,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #undef CONFIG_CMD_NET #undef CONFIG_CMD_NFS diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index 5ff65c6..7e9c55e 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -136,10 +136,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #undef CONFIG_CMD_NET #undef CONFIG_CMD_NFS diff --git a/include/configs/bct-brettl2.h b/include/configs/bct-brettl2.h index ce09c2e..5b09b45 100644 --- a/include/configs/bct-brettl2.h +++ b/include/configs/bct-brettl2.h @@ -111,8 +111,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index 7144c63..a22c868 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -155,8 +155,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/bf537-pnav.h b/include/configs/bf537-pnav.h index 62bd3bf..3aa3d50 100644 --- a/include/configs/bf537-pnav.h +++ b/include/configs/bf537-pnav.h @@ -111,8 +111,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index 25cebf8..02945be 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -118,8 +118,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/bf538f-ezkit.h b/include/configs/bf538f-ezkit.h index 77822e7..ffb0caf 100644 --- a/include/configs/bf538f-ezkit.h +++ b/include/configs/bf538f-ezkit.h @@ -115,8 +115,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/cm-bf537e.h b/include/configs/cm-bf537e.h index 77f47d9..8f10eba 100644 --- a/include/configs/cm-bf537e.h +++ b/include/configs/cm-bf537e.h @@ -112,8 +112,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/cm-bf537u.h b/include/configs/cm-bf537u.h index 55e61d6..a1c8e8a 100644 --- a/include/configs/cm-bf537u.h +++ b/include/configs/cm-bf537u.h @@ -110,8 +110,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index a6c63cb..f4ecd0d 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -141,10 +141,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_I2C_MULTI_BUS diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index 8343891..474a568 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -90,10 +90,10 @@ #define CONFIG_DOS_PARTITION 1 /* I2C */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* TWL4030 */ #define CONFIG_TWL4030_POWER 1 diff --git a/include/configs/dig297.h b/include/configs/dig297.h index c19c4c7..5049afc 100644 --- a/include/configs/dig297.h +++ b/include/configs/dig297.h @@ -123,10 +123,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/dnp5370.h b/include/configs/dnp5370.h index f2f4102..d0e72e3 100644 --- a/include/configs/dnp5370.h +++ b/include/configs/dnp5370.h @@ -85,8 +85,8 @@ #define ENV_IS_EMBEDDED #define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); diff --git a/include/configs/ecovec.h b/include/configs/ecovec.h index 335e9cd..3483cf1 100644 --- a/include/configs/ecovec.h +++ b/include/configs/ecovec.h @@ -58,18 +58,17 @@ /* I2C */ #define CONFIG_CMD_I2C -#define CONFIG_SH_I2C 1 -#define CONFIG_HARD_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_SYS_MAX_I2C_BUS 2 -#define CONFIG_SYS_I2C_MODULE 1 -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SH #define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 2 +#define CONFIG_SYS_I2C_SH_BASE0 0xA4470000 +#define CONFIG_SYS_I2C_SH_SPEED0 100000 +#define CONFIG_SYS_I2C_SH_BASE1 0xA4750000 +#define CONFIG_SYS_I2C_SH_SPEED1 100000 #define CONFIG_SH_I2C_DATA_HIGH 4 #define CONFIG_SH_I2C_DATA_LOW 5 #define CONFIG_SH_I2C_CLOCK 41666666 -#define CONFIG_SH_I2C_BASE0 0xA4470000 -#define CONFIG_SH_I2C_BASE1 0xA4750000 /* Ether */ #define CONFIG_SH_ETHER 1 diff --git a/include/configs/highbank.h b/include/configs/highbank.h index b86eb43..7dbee3c 100644 --- a/include/configs/highbank.h +++ b/include/configs/highbank.h @@ -8,7 +8,6 @@ #define __CONFIG_H #define CONFIG_SYS_DCACHE_OFF -#define CONFIG_L2_OFF #define CONFIG_SYS_THUMB_BUILD #define CONFIG_SYS_NO_FLASH diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h index 5291755..ac5ca9a 100644 --- a/include/configs/ibf-dsp561.h +++ b/include/configs/ibf-dsp561.h @@ -95,8 +95,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/kzm9g.h b/include/configs/kzm9g.h index 1afd487..f183279 100644 --- a/include/configs/kzm9g.h +++ b/include/configs/kzm9g.h @@ -22,7 +22,6 @@ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO #define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_L2_OFF #define CONFIG_OF_LIBFDT #include <config_cmd_default.h> @@ -139,21 +138,22 @@ /* I2C */ #define CONFIG_CMD_I2C -#define CONFIG_SH_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SH +#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 5 +#define CONFIG_SYS_I2C_SH_BASE0 0xE6820000 +#define CONFIG_SYS_I2C_SH_SPEED0 100000 +#define CONFIG_SYS_I2C_SH_BASE1 0xE6822000 +#define CONFIG_SYS_I2C_SH_SPEED1 100000 +#define CONFIG_SYS_I2C_SH_BASE2 0xE6824000 +#define CONFIG_SYS_I2C_SH_SPEED2 100000 +#define CONFIG_SYS_I2C_SH_BASE3 0xE6826000 +#define CONFIG_SYS_I2C_SH_SPEED3 100000 +#define CONFIG_SYS_I2C_SH_BASE4 0xE6828000 +#define CONFIG_SYS_I2C_SH_SPEED4 100000 #define CONFIG_SH_I2C_8BIT -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_MAX_I2C_BUS (5) -#define CONFIG_SYS_I2C_MODULE -#define CONFIG_SYS_I2C_SPEED (100000) /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE (0x7F) -#define CONFIG_SH_I2C_DATA_HIGH (4) -#define CONFIG_SH_I2C_DATA_LOW (5) -#define CONFIG_SH_I2C_CLOCK (104000000) /* 104 MHz */ -#define CONFIG_SH_I2C_BASE0 (0xE6820000) -#define CONFIG_SH_I2C_BASE1 (0xE6822000) -#define CONFIG_SH_I2C_BASE2 (0xE6824000) -#define CONFIG_SH_I2C_BASE3 (0xE6826000) -#define CONFIG_SH_I2C_BASE4 (0xE6828000) +#define CONFIG_SH_I2C_DATA_HIGH 4 +#define CONFIG_SH_I2C_DATA_LOW 5 +#define CONFIG_SH_I2C_CLOCK 104000000 /* 104 MHz */ #endif /* __KZM9G_H */ diff --git a/include/configs/mcx.h b/include/configs/mcx.h index 4619dfb..a2f7cf7 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -137,10 +137,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* RTC */ #define CONFIG_RTC_DS1337 diff --git a/include/configs/mx51_efikamx.h b/include/configs/mx51_efikamx.h index 8a44ef5..0f2a4ef 100644 --- a/include/configs/mx51_efikamx.h +++ b/include/configs/mx51_efikamx.h @@ -29,7 +29,6 @@ #define CONFIG_SYS_TEXT_BASE 0x97800000 -#define CONFIG_L2_OFF #define CONFIG_SYS_ICACHE_OFF #define CONFIG_SYS_DCACHE_OFF diff --git a/include/configs/nokia_rx51.h b/include/configs/nokia_rx51.h index 4332779..e0c0fac 100644 --- a/include/configs/nokia_rx51.h +++ b/include/configs/nokia_rx51.h @@ -157,10 +157,10 @@ #undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ #define CONFIG_OMAP3_SPI -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 47d9902..bba39d4 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -161,11 +161,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_VIDEO_OMAP3 /* DSS Support */ /* diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h index 3eae288..43616e2 100644 --- a/include/configs/omap3_evm_common.h +++ b/include/configs/omap3_evm_common.h @@ -87,11 +87,10 @@ /* * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_DRIVER_OMAP34XX_I2C - -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * PISMO support diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h index ac36ac6..75d7d70 100644 --- a/include/configs/omap3_igep00x0.h +++ b/include/configs/omap3_igep00x0.h @@ -124,10 +124,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_OMAP34XX +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 /* * TWL4030 diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index 0c096f4..bedd6f9 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -118,12 +118,10 @@ /* * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_DRIVER_OMAP34XX_I2C - -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_mvblx.h b/include/configs/omap3_mvblx.h index 45da2e0..8d11010 100644 --- a/include/configs/omap3_mvblx.h +++ b/include/configs/omap3_mvblx.h @@ -128,11 +128,10 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_FPGA -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index 4641694..84b4aee 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -98,11 +98,10 @@ #define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h index 3cce0de..eacdfaa 100644 --- a/include/configs/omap3_pandora.h +++ b/include/configs/omap3_pandora.h @@ -111,10 +111,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h index 697a3f3..6f1304d 100644 --- a/include/configs/omap3_sdp3430.h +++ b/include/configs/omap3_sdp3430.h @@ -114,10 +114,10 @@ /* * I2C for power management setup */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* OMITTED: single 1 Gbit MT29F1G NAND flash */ diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h index 8591f98..1dd53fa 100644 --- a/include/configs/omap3_zoom1.h +++ b/include/configs/omap3_zoom1.h @@ -118,10 +118,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h index cb8c7ec..f749740 100644 --- a/include/configs/omap3_zoom2.h +++ b/include/configs/omap3_zoom2.h @@ -138,10 +138,10 @@ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX /* * TWL4030 diff --git a/include/configs/origen.h b/include/configs/origen.h index bad34b3..f46b833 100644 --- a/include/configs/origen.h +++ b/include/configs/origen.h @@ -22,8 +22,6 @@ #define CONFIG_DISPLAY_BOARDINFO #define CONFIG_BOARD_EARLY_INIT_F -/* Keep L2 Cache Disabled */ -#define CONFIG_L2_OFF 1 #define CONFIG_SYS_DCACHE_OFF 1 #define CONFIG_SYS_SDRAM_BASE 0x40000000 diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 4970b13..6f41ee7 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -172,11 +172,10 @@ /* I2C Configuration */ #define CONFIG_I2C #define CONFIG_CMD_I2C -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP24XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX #define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */ diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index 9eb0a04..745e3be 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -131,11 +131,10 @@ /* I2C Configuration */ #define CONFIG_I2C #define CONFIG_CMD_I2C -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP24XX_I2C - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED OMAP_I2C_STANDARD +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX /* Defines for SPL */ #define CONFIG_SPL diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h index e2e8efe..1388f49 100644 --- a/include/configs/smdkv310.h +++ b/include/configs/smdkv310.h @@ -25,9 +25,6 @@ /* Mach Type */ #define CONFIG_MACH_TYPE MACH_TYPE_SMDKV310 -/* Keep L2 Cache Disabled */ -#define CONFIG_L2_OFF 1 - #define CONFIG_SYS_SDRAM_BASE 0x40000000 #define CONFIG_SYS_TEXT_BASE 0x43E00000 diff --git a/include/configs/snowball.h b/include/configs/snowball.h index 00d6fa5..9a069f3 100644 --- a/include/configs/snowball.h +++ b/include/configs/snowball.h @@ -23,7 +23,6 @@ * (easy to change) */ #define CONFIG_U8500 -#define CONFIG_L2_OFF #define CONFIG_SYS_MEMTEST_START 0x00000000 #define CONFIG_SYS_MEMTEST_END 0x1FFFFFFF diff --git a/include/configs/socfpga_cyclone5.h b/include/configs/socfpga_cyclone5.h index 980636c..608578a 100644 --- a/include/configs/socfpga_cyclone5.h +++ b/include/configs/socfpga_cyclone5.h @@ -16,7 +16,6 @@ #define CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_ARMV7 -#define CONFIG_L2_OFF #define CONFIG_SYS_DCACHE_OFF #undef CONFIG_USE_IRQ diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index 683bc54..6112c1b 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -117,14 +117,13 @@ #undef CONFIG_CMD_IMLS #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 400000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_DRIVER_OMAP34XX_I2C - /* * Board NAND Info. @@ -369,7 +368,7 @@ struct tam3517_module_info { #define TAM3517_READ_EEPROM(info, ret) \ do { \ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); \ + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \ if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ (void *)info, sizeof(*info))) \ ret = 1; \ diff --git a/include/configs/tcm-bf537.h b/include/configs/tcm-bf537.h index 2adb071..627836a 100644 --- a/include/configs/tcm-bf537.h +++ b/include/configs/tcm-bf537.h @@ -112,8 +112,8 @@ * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ - arch/blackfin/lib/libblackfin.o (.text*); \ - arch/blackfin/cpu/libblackfin.o (.text*); \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h index 84269ad..99b60fc 100644 --- a/include/configs/ti_armv7_common.h +++ b/include/configs/ti_armv7_common.h @@ -59,12 +59,11 @@ /* I2C IP block */ #define CONFIG_I2C -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_DRIVER_OMAP24XX_I2C #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX /* MMC/SD IP block */ #define CONFIG_MMC diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h index d57394e..afd8707 100644 --- a/include/configs/tricorder.h +++ b/include/configs/tricorder.h @@ -98,11 +98,11 @@ #define CONFIG_DOS_PARTITION /* I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C 1 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX + /* EEPROM */ #define CONFIG_SYS_I2C_MULTI_EEPROMS diff --git a/include/configs/u8500_href.h b/include/configs/u8500_href.h index 45d33a6..629299d 100644 --- a/include/configs/u8500_href.h +++ b/include/configs/u8500_href.h @@ -12,7 +12,6 @@ * (easy to change) */ #define CONFIG_U8500 -#define CONFIG_L2_OFF #define CONFIG_SYS_MEMTEST_START 0x00000000 #define CONFIG_SYS_MEMTEST_END 0x1FFFFFFF diff --git a/include/configs/zynq.h b/include/configs/zynq.h index 4c6e6e8..82ec826 100644 --- a/include/configs/zynq.h +++ b/include/configs/zynq.h @@ -60,10 +60,10 @@ /* I2C */ #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1) # define CONFIG_CMD_I2C -# define CONFIG_ZYNQ_I2C -# define CONFIG_HARD_I2C -# define CONFIG_SYS_I2C_SPEED 100000 -# define CONFIG_SYS_I2C_SLAVE 1 +# define CONFIG_SYS_I2C +# define CONFIG_SYS_I2C_ZYNQ +# define CONFIG_SYS_I2C_ZYNQ_SPEED 100000 +# define CONFIG_SYS_I2C_ZYNQ_SLAVE 1 #endif #if defined(CONFIG_ZYNQ_DCC) diff --git a/lib/lzma/Makefile b/lib/lzma/Makefile index 25c6797..f8eda06 100644 --- a/lib/lzma/Makefile +++ b/lib/lzma/Makefile @@ -10,4 +10,4 @@ CFLAGS += -D_LZMA_PROB32 -obj-$(CONFIG_LZMA) += LzmaDec.o LzmaTools.o +obj-y += LzmaDec.o LzmaTools.o diff --git a/lib/lzo/Makefile b/lib/lzo/Makefile index dd853ea..2936544 100644 --- a/lib/lzo/Makefile +++ b/lib/lzo/Makefile @@ -5,4 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_LZO) += lzo1x_decompress.o +obj-y += lzo1x_decompress.o diff --git a/lib/rsa/Makefile b/lib/rsa/Makefile index 693c745..164ab39 100644 --- a/lib/rsa/Makefile +++ b/lib/rsa/Makefile @@ -7,6 +7,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifdef CONFIG_FIT_SIGNATURE -obj-$(CONFIG_RSA) += rsa-verify.o -endif +obj-$(CONFIG_FIT_SIGNATURE) += rsa-verify.o diff --git a/lib/zlib/Makefile b/lib/zlib/Makefile index 1e9e04d..2fba95f 100644 --- a/lib/zlib/Makefile +++ b/lib/zlib/Makefile @@ -5,4 +5,4 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-$(CONFIG_ZLIB) += zlib.o +obj-y += zlib.o diff --git a/scripts/Makefile.build b/scripts/Makefile.build index 2ef7341..e3354aa 100644 --- a/scripts/Makefile.build +++ b/scripts/Makefile.build @@ -10,10 +10,6 @@ SRCS := include Makefile -# Backward compatible: obj-y is preferable -COBJS := $(sort $(COBJS) $(COBJS-y)) -SOBJS := $(sort $(SOBJS) $(SOBJS-y)) - # Going forward use the following obj-y := $(sort $(obj-y)) extra-y := $(sort $(extra-y)) @@ -24,11 +20,18 @@ obj-y := $(patsubst %/, %/built-in.o, $(obj-y)) subdir-obj-y := $(filter %/built-in.o, $(obj-y)) subdir-obj-y := $(addprefix $(obj),$(subdir-obj-y)) -SRCS += $(COBJS:.o=.c) $(SOBJS:.o=.S) \ - $(wildcard $(obj-y:.o=.c) $(obj-y:.o=.S) $(lib-y:.o=.c) $(lib-y:.o=.S) $(extra-y:.o=.c) $(extra-y:.o=.S)) -OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS) $(obj-y)) +SRCS += $(wildcard $(obj-y:.o=.c) $(obj-y:.o=.S) $(lib-y:.o=.c) \ + $(lib-y:.o=.S) $(extra-y:.o=.c) $(extra-y:.o=.S)) +OBJS := $(addprefix $(obj),$(obj-y)) + +# $(obj-dirs) is a list of directories that contain object files +obj-dirs := $(dir $(OBJS)) + +# Create directories for object files if directory does not exist +# Needed when obj-y := dir/file.o syntax is used +_dummy := $(foreach d,$(obj-dirs), $(shell [ -d $(d) ] || mkdir -p $(d))) -LGOBJS := $(addprefix $(obj),$(sort $(GLSOBJS) $(GLCOBJS)) $(lib-y)) +LGOBJS := $(addprefix $(obj),$(sort $(lib-y))) all: $(LIB) $(addprefix $(obj),$(extra-y)) diff --git a/spl/Makefile b/spl/Makefile index cbd3d27..29d7818 100644 --- a/spl/Makefile +++ b/spl/Makefile @@ -54,63 +54,54 @@ ifeq ($(CPU),mpc85xx) START += $(START_PATH)/resetvec.o endif -LIBS-y += arch/$(ARCH)/lib/lib$(ARCH).o +LIBS-y += arch/$(ARCH)/lib/ -LIBS-y += $(CPUDIR)/lib$(CPU).o -ifeq ($(CPU),mpc83xx) -LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o -endif -ifeq ($(CPU),mpc85xx) -LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o -ifdef CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT -LIBS-y += arch/powerpc/cpu/mpc8xxx/ddr/libddr.o -endif -endif -ifeq ($(CPU),mpc86xx) -LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o -endif +LIBS-y += $(CPUDIR)/ ifdef SOC -LIBS-y += $(CPUDIR)/$(SOC)/lib$(SOC).o -endif -LIBS-y += board/$(BOARDDIR)/lib$(BOARD).o -LIBS-$(HAVE_VENDOR_COMMON_LIB) += board/$(VENDOR)/common/lib$(VENDOR).o - -LIBS-$(CONFIG_SPL_FRAMEWORK) += common/spl/libspl.o -LIBS-$(CONFIG_SPL_LIBCOMMON_SUPPORT) += common/libcommon.o -LIBS-$(CONFIG_SPL_LIBDISK_SUPPORT) += disk/libdisk.o -LIBS-$(CONFIG_SPL_I2C_SUPPORT) += drivers/i2c/libi2c.o -LIBS-$(CONFIG_SPL_GPIO_SUPPORT) += drivers/gpio/libgpio.o -LIBS-$(CONFIG_SPL_MMC_SUPPORT) += drivers/mmc/libmmc.o -LIBS-$(CONFIG_SPL_SERIAL_SUPPORT) += drivers/serial/libserial.o -LIBS-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += drivers/mtd/spi/libspi_flash.o -LIBS-$(CONFIG_SPL_SPI_SUPPORT) += drivers/spi/libspi.o -LIBS-$(CONFIG_SPL_FAT_SUPPORT) += fs/fat/libfat.o -LIBS-$(CONFIG_SPL_LIBGENERIC_SUPPORT) += lib/libgeneric.o -LIBS-$(CONFIG_SPL_POWER_SUPPORT) += drivers/power/libpower.o \ - drivers/power/pmic/libpmic.o -LIBS-$(CONFIG_SPL_NAND_SUPPORT) += drivers/mtd/nand/libnand.o -LIBS-$(CONFIG_SPL_ONENAND_SUPPORT) += drivers/mtd/onenand/libonenand.o -LIBS-$(CONFIG_SPL_DMA_SUPPORT) += drivers/dma/libdma.o -LIBS-$(CONFIG_SPL_POST_MEM_SUPPORT) += post/drivers/memory.o -LIBS-$(CONFIG_SPL_NET_SUPPORT) += net/libnet.o -LIBS-$(CONFIG_SPL_ETH_SUPPORT) += drivers/net/libnet.o -LIBS-$(CONFIG_SPL_ETH_SUPPORT) += drivers/net/phy/libphy.o -LIBS-$(CONFIG_SPL_USBETH_SUPPORT) += drivers/net/phy/libphy.o -LIBS-$(CONFIG_SPL_MUSB_NEW_SUPPORT) += drivers/usb/musb-new/libusb_musb-new.o -LIBS-$(CONFIG_SPL_USBETH_SUPPORT) += drivers/usb/gadget/libusb_gadget.o -LIBS-$(CONFIG_SPL_WATCHDOG_SUPPORT) += drivers/watchdog/libwatchdog.o +LIBS-y += $(CPUDIR)/$(SOC)/ +endif +LIBS-y += board/$(BOARDDIR)/ +LIBS-$(HAVE_VENDOR_COMMON_LIB) += board/$(VENDOR)/common/ + +LIBS-$(CONFIG_SPL_FRAMEWORK) += common/spl/ +LIBS-$(CONFIG_SPL_LIBCOMMON_SUPPORT) += common/ +LIBS-$(CONFIG_SPL_LIBDISK_SUPPORT) += disk/ +LIBS-$(CONFIG_SPL_I2C_SUPPORT) += drivers/i2c/ +LIBS-$(CONFIG_SPL_GPIO_SUPPORT) += drivers/gpio/ +LIBS-$(CONFIG_SPL_MMC_SUPPORT) += drivers/mmc/ +LIBS-$(CONFIG_SPL_SERIAL_SUPPORT) += drivers/serial/ +LIBS-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += drivers/mtd/spi/ +LIBS-$(CONFIG_SPL_SPI_SUPPORT) += drivers/spi/ +LIBS-y += fs/ +LIBS-$(CONFIG_SPL_LIBGENERIC_SUPPORT) += lib/ +LIBS-$(CONFIG_SPL_POWER_SUPPORT) += drivers/power/ \ + drivers/power/pmic/ +LIBS-$(CONFIG_SPL_NAND_SUPPORT) += drivers/mtd/nand/ +LIBS-$(CONFIG_SPL_ONENAND_SUPPORT) += drivers/mtd/onenand/ +LIBS-$(CONFIG_SPL_DMA_SUPPORT) += drivers/dma/ +LIBS-$(CONFIG_SPL_POST_MEM_SUPPORT) += post/drivers/ +LIBS-$(CONFIG_SPL_NET_SUPPORT) += net/ +LIBS-$(CONFIG_SPL_ETH_SUPPORT) += drivers/net/ +LIBS-$(CONFIG_SPL_ETH_SUPPORT) += drivers/net/phy/ +LIBS-$(CONFIG_SPL_USBETH_SUPPORT) += drivers/net/phy/ +LIBS-$(CONFIG_SPL_MUSB_NEW_SUPPORT) += drivers/usb/musb-new/ +LIBS-$(CONFIG_SPL_USBETH_SUPPORT) += drivers/usb/gadget/ +LIBS-$(CONFIG_SPL_WATCHDOG_SUPPORT) += drivers/watchdog/ ifneq (,$(CONFIG_MX23)$(filter $(SOC), mx25 mx27 mx5 mx6 mx31 mx35)) -LIBS-y += arch/$(ARCH)/imx-common/libimx-common.o +LIBS-y += arch/$(ARCH)/imx-common/ endif -LIBS-$(CONFIG_ARM) += arch/arm/cpu/libcpu.o +LIBS-$(CONFIG_ARM) += arch/arm/cpu/ +LIBS-$(CONFIG_PPC) += arch/powerpc/cpu/ ifneq ($(CONFIG_MX23)$(CONFIG_MX35),) -LIBS-y += arch/$(ARCH)/imx-common/libimx-common.o +LIBS-y += arch/$(ARCH)/imx-common/ endif +LIBS-y := $(patsubst %/, %/built-in.o, $(LIBS-y)) + # Add GCC lib ifeq ("$(USE_PRIVATE_LIBGCC)", "yes") PLATFORM_LIBGCC = $(SPLTREE)/arch/$(ARCH)/lib/libgcc.o @@ -175,8 +166,7 @@ all: $(ALL-y) ifdef CONFIG_SAMSUNG $(obj)$(BOARD)-spl.bin: $(obj)u-boot-spl.bin - $(OBJTREE)/tools/mk$(BOARD)spl \ - $(obj)u-boot-spl.bin $(obj)$(BOARD)-spl.bin + $(OBJTREE)/tools/mk$(BOARD)spl $< $@ endif $(obj)$(SPL_BIN).bin: $(obj)$(SPL_BIN) @@ -195,7 +185,6 @@ $(START): $(LIBS): depend $(MAKE) $(build) $(SRCTREE)$(dir $(subst $(SPLTREE),,$@)) - mv $(dir $@)built-in.o $@ $(obj)u-boot-spl.lds: $(LDSCRIPT) depend $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -I$(obj). -ansi -D__ASSEMBLY__ -P - < $< > $@ diff --git a/tools/gdb/Makefile b/tools/gdb/Makefile index dee91fc..dd98fb6 100644 --- a/tools/gdb/Makefile +++ b/tools/gdb/Makefile @@ -23,8 +23,6 @@ BINS := $(addprefix $(obj),$(BINS)) # HOSTCPPFLAGS = -I$(BFD_ROOT_DIR)/include -HOSTOS := $(shell uname -s | sed -e 's/\([Cc][Yy][Gg][Ww][Ii][Nn]\).*/cygwin/') - ifeq ($(HOSTOS),cygwin) all: |