summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/sbc8548/law.c5
-rw-r--r--board/sbc8548/tlb.c2
-rw-r--r--doc/README.sbc854821
-rw-r--r--include/configs/sbc8548.h13
4 files changed, 40 insertions, 1 deletions
diff --git a/board/sbc8548/law.c b/board/sbc8548/law.c
index c263191..322af76 100644
--- a/board/sbc8548/law.c
+++ b/board/sbc8548/law.c
@@ -59,8 +59,13 @@ struct law_entry law_table[] = {
#ifndef CONFIG_SPD_EEPROM
SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR),
#endif
+#ifdef CONFIG_SYS_LBC_SDRAM_BASE
/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+#else
+ /* LBC window - maps 128M 0xf8000000 -> 0xffffffff */
+ SET_LAW(CONFIG_SYS_EPLD_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
+#endif
};
int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/sbc8548/tlb.c b/board/sbc8548/tlb.c
index 4bf7214..af927f1 100644
--- a/board/sbc8548/tlb.c
+++ b/board/sbc8548/tlb.c
@@ -76,6 +76,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 2, BOOKE_PAGESZ_64M, 1),
+#ifdef CONFIG_SYS_LBC_SDRAM_BASE
/*
* TLB 3: 64M Cacheable, non-guarded
* 0xf0000000 64M LBC SDRAM First half
@@ -92,6 +93,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
CONFIG_SYS_LBC_SDRAM_BASE + 0x4000000,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 4, BOOKE_PAGESZ_64M, 1),
+#endif
/*
* TLB 5: 16M Cacheable, non-guarded
diff --git a/doc/README.sbc8548 b/doc/README.sbc8548
index e6b8abe..f9e2dea 100644
--- a/doc/README.sbc8548
+++ b/doc/README.sbc8548
@@ -62,6 +62,27 @@ a 33MHz PCI configuration is currently untested.)
02.00.00 0x1148 0x9e00 Network controller 0x00
=>
+Memory Size and using SPD:
+==========================
+
+The default configuration uses hard coded memory configuration settings
+for 256MB of DDR2 @400MHz. It does not by default use the DDR2 SPD
+EEPROM data to read what memory is installed.
+
+There is a hardware errata, which causes the older local bus SDRAM
+SPD EEPROM to land at the same address as the DDR2 SPD EEPROM, so
+that the SPD data can not be read reliably.
+
+If you want to upgrade to larger RAM size, you can simply enable
+ #define CONFIG_SPD_EEPROM
+ #define CONFIG_DDR_SPD
+in include/configs/sbc8548.h file. (The lines are already there
+but listed as #undef).
+
+Note that you will have to physically remove the LBC 128MB DIMM
+from the board's socket to resolve the above i2c address overlap
+issue and allow SPD autodetection of RAM to work.
+
Updating U-boot with U-boot:
============================
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 1df2225..44c7526 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -119,9 +119,15 @@
/* DDR Setup */
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+/*
+ * A hardware errata caused the LBC SDRAM SPD and the DDR2 SPD
+ * to collide, meaning you couldn't reliably read either. So
+ * physically remove the LBC PC100 SDRAM module from the board
+ * before enabling the two SPD options below.
+ */
#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#undef CONFIG_DDR_SPD
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
@@ -283,9 +289,14 @@
/*
* SDRAM on the Local Bus (CS3 and CS4)
+ * Note that most boards have a hardware errata where both the
+ * LBC SDRAM and the DDR2 SDRAM decode at 0x51, making it impossible
+ * to use CONFIG_DDR_SPD unless you physically remove the LBC DIMM.
*/
+#ifndef CONFIG_DDR_SPD
#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
#define CONFIG_SYS_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */
+#endif
/*
* Base Register 3 and Option Register 3 configure the 1st 1/2 SDRAM.