summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--common/Makefile1
-rw-r--r--common/miiphyutil.c181
-rw-r--r--drivers/net/phy/Makefile2
-rw-r--r--drivers/net/phy/generic_10g.c105
-rw-r--r--drivers/net/phy/phy.c724
-rw-r--r--include/linux/ethtool.h721
-rw-r--r--include/linux/mdio.h278
-rw-r--r--include/miiphy.h17
-rw-r--r--include/phy.h219
-rw-r--r--net/eth.c6
10 files changed, 2218 insertions, 36 deletions
diff --git a/common/Makefile b/common/Makefile
index 4555716..02dbeed 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -115,6 +115,7 @@ COBJS-$(CONFIG_CMD_MFSL) += cmd_mfsl.o
COBJS-$(CONFIG_CMD_MG_DISK) += cmd_mgdisk.o
COBJS-$(CONFIG_MII) += miiphyutil.o
COBJS-$(CONFIG_CMD_MII) += miiphyutil.o
+COBJS-$(CONFIG_PHYLIB) += miiphyutil.o
COBJS-$(CONFIG_CMD_MII) += cmd_mii.o
COBJS-$(CONFIG_CMD_MISC) += cmd_misc.o
COBJS-$(CONFIG_CMD_MMC) += cmd_mmc.o
diff --git a/common/miiphyutil.c b/common/miiphyutil.c
index 6944ea7..243cae9 100644
--- a/common/miiphyutil.c
+++ b/common/miiphyutil.c
@@ -28,6 +28,7 @@
#include <common.h>
#include <miiphy.h>
+#include <phy.h>
#include <asm/types.h>
#include <linux/list.h>
@@ -44,22 +45,13 @@
#define debug(fmt, args...)
#endif /* MII_DEBUG */
-struct mii_dev {
- struct list_head link;
- const char *name;
- int (*read)(const char *devname, unsigned char addr,
- unsigned char reg, unsigned short *value);
- int (*write)(const char *devname, unsigned char addr,
- unsigned char reg, unsigned short value);
-};
-
static struct list_head mii_devs;
static struct mii_dev *current_mii;
/*
* Lookup the mii_dev struct by the registered device name.
*/
-static struct mii_dev *miiphy_get_dev_by_name(const char *devname, int quiet)
+struct mii_dev *miiphy_get_dev_by_name(const char *devname)
{
struct list_head *entry;
struct mii_dev *dev;
@@ -75,8 +67,6 @@ static struct mii_dev *miiphy_get_dev_by_name(const char *devname, int quiet)
return dev;
}
- if (!quiet)
- printf("No such device: %s\n", devname);
return NULL;
}
@@ -90,6 +80,25 @@ void miiphy_init(void)
current_mii = NULL;
}
+static int legacy_miiphy_read(struct mii_dev *bus, int addr, int devad, int reg)
+{
+ unsigned short val;
+ int ret;
+ struct legacy_mii_dev *ldev = bus->priv;
+
+ ret = ldev->read(bus->name, addr, reg, &val);
+
+ return ret ? -1 : (int)val;
+}
+
+static int legacy_miiphy_write(struct mii_dev *bus, int addr, int devad,
+ int reg, u16 val)
+{
+ struct legacy_mii_dev *ldev = bus->priv;
+
+ return ldev->write(bus->name, addr, reg, val);
+}
+
/*****************************************************************************
*
* Register read and write MII access routines for the device <name>.
@@ -101,11 +110,11 @@ void miiphy_register(const char *name,
unsigned char reg, unsigned short value))
{
struct mii_dev *new_dev;
+ struct legacy_mii_dev *ldev;
unsigned int name_len;
- char *new_name;
/* check if we have unique name */
- new_dev = miiphy_get_dev_by_name(name, 1);
+ new_dev = miiphy_get_dev_by_name(name);
if (new_dev) {
printf("miiphy_register: non unique device name '%s'\n", name);
return;
@@ -113,26 +122,32 @@ void miiphy_register(const char *name,
/* allocate memory */
name_len = strlen(name);
- new_dev =
- (struct mii_dev *)malloc(sizeof(struct mii_dev) + name_len + 1);
+ if (name_len > MDIO_NAME_LEN - 1) {
+ /* Hopefully this won't happen, but if it does, we'll know */
+ printf("miiphy_register: MDIO name was longer than %d\n",
+ MDIO_NAME_LEN);
+ return;
+ }
- if (new_dev == NULL) {
+ new_dev = mdio_alloc();
+ ldev = malloc(sizeof(*ldev));
+
+ if (new_dev == NULL || ldev == NULL) {
printf("miiphy_register: cannot allocate memory for '%s'\n",
name);
return;
}
- memset(new_dev, 0, sizeof(struct mii_dev) + name_len);
/* initalize mii_dev struct fields */
- INIT_LIST_HEAD(&new_dev->link);
- new_dev->read = read;
- new_dev->write = write;
- new_dev->name = new_name = (char *)(new_dev + 1);
- strncpy(new_name, name, name_len);
- new_name[name_len] = '\0';
+ new_dev->read = legacy_miiphy_read;
+ new_dev->write = legacy_miiphy_write;
+ sprintf(new_dev->name, name);
+ ldev->read = read;
+ ldev->write = write;
+ new_dev->priv = ldev;
debug("miiphy_register: added '%s', read=0x%08lx, write=0x%08lx\n",
- new_dev->name, new_dev->read, new_dev->write);
+ new_dev->name, ldev->read, ldev->write);
/* add it to the list */
list_add_tail(&new_dev->link, &mii_devs);
@@ -141,19 +156,110 @@ void miiphy_register(const char *name,
current_mii = new_dev;
}
+struct mii_dev *mdio_alloc(void)
+{
+ struct mii_dev *bus;
+
+ bus = malloc(sizeof(*bus));
+ if (!bus)
+ return bus;
+
+ memset(bus, 0, sizeof(*bus));
+
+ /* initalize mii_dev struct fields */
+ INIT_LIST_HEAD(&bus->link);
+
+ return bus;
+}
+
+int mdio_register(struct mii_dev *bus)
+{
+ if (!bus || !bus->name || !bus->read || !bus->write)
+ return -1;
+
+ /* check if we have unique name */
+ if (miiphy_get_dev_by_name(bus->name)) {
+ printf("mdio_register: non unique device name '%s'\n",
+ bus->name);
+ return -1;
+ }
+
+ /* add it to the list */
+ list_add_tail(&bus->link, &mii_devs);
+
+ if (!current_mii)
+ current_mii = bus;
+
+ return 0;
+}
+
+void mdio_list_devices(void)
+{
+ struct list_head *entry;
+
+ list_for_each(entry, &mii_devs) {
+ int i;
+ struct mii_dev *bus = list_entry(entry, struct mii_dev, link);
+
+ printf("%s:\n", bus->name);
+
+ for (i = 0; i < PHY_MAX_ADDR; i++) {
+ struct phy_device *phydev = bus->phymap[i];
+
+ if (phydev) {
+ printf("%d - %s", i, phydev->drv->name);
+
+ if (phydev->dev)
+ printf(" <--> %s\n", phydev->dev->name);
+ else
+ printf("\n");
+ }
+ }
+ }
+}
+
int miiphy_set_current_dev(const char *devname)
{
struct mii_dev *dev;
- dev = miiphy_get_dev_by_name(devname, 0);
+ dev = miiphy_get_dev_by_name(devname);
if (dev) {
current_mii = dev;
return 0;
}
+ printf("No such device: %s\n", devname);
+
return 1;
}
+struct mii_dev *mdio_get_current_dev(void)
+{
+ return current_mii;
+}
+
+struct phy_device *mdio_phydev_for_ethname(const char *ethname)
+{
+ struct list_head *entry;
+ struct mii_dev *bus;
+
+ list_for_each(entry, &mii_devs) {
+ int i;
+ bus = list_entry(entry, struct mii_dev, link);
+
+ for (i = 0; i < PHY_MAX_ADDR; i++) {
+ if (!bus->phymap[i] || !bus->phymap[i]->dev)
+ continue;
+
+ if (strcmp(bus->phymap[i]->dev->name, ethname) == 0)
+ return bus->phymap[i];
+ }
+ }
+
+ printf("%s is not a known ethernet\n", ethname);
+ return NULL;
+}
+
const char *miiphy_get_current_dev(void)
{
if (current_mii)
@@ -187,13 +293,15 @@ static struct mii_dev *miiphy_get_active_dev(const char *devname)
int miiphy_read(const char *devname, unsigned char addr, unsigned char reg,
unsigned short *value)
{
- struct mii_dev *dev;
+ struct mii_dev *bus;
- dev = miiphy_get_active_dev(devname);
- if (dev)
- return dev->read(devname, addr, reg, value);
+ bus = miiphy_get_active_dev(devname);
+ if (bus)
+ *value = bus->read(bus, addr, MDIO_DEVAD_NONE, reg);
+ else
+ return 1;
- return 1;
+ return (*value < 0) ? 1 : 0;
}
/*****************************************************************************
@@ -207,11 +315,11 @@ int miiphy_read(const char *devname, unsigned char addr, unsigned char reg,
int miiphy_write(const char *devname, unsigned char addr, unsigned char reg,
unsigned short value)
{
- struct mii_dev *dev;
+ struct mii_dev *bus;
- dev = miiphy_get_active_dev(devname);
- if (dev)
- return dev->write(devname, addr, reg, value);
+ bus = miiphy_get_active_dev(devname);
+ if (bus)
+ return bus->write(bus, addr, MDIO_DEVAD_NONE, reg, value);
return 1;
}
@@ -279,6 +387,7 @@ int miiphy_info(const char *devname, unsigned char addr, unsigned int *oui,
return 0;
}
+#ifndef CONFIG_PHYLIB
/*****************************************************************************
*
* Reset the PHY.
@@ -322,6 +431,7 @@ int miiphy_reset(const char *devname, unsigned char addr)
}
return 0;
}
+#endif /* !PHYLIB */
/*****************************************************************************
*
@@ -352,7 +462,6 @@ int miiphy_speed(const char *devname, unsigned char addr)
if (btsr != 0xFFFF &&
(btsr & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)))
return _1000BASET;
-
#endif /* CONFIG_PHY_GIGE */
/* Check Basic Management Control Register first. */
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index bba8901..609a22f 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -27,6 +27,8 @@ LIB := $(obj)libphy.o
COBJS-$(CONFIG_BITBANGMII) += miiphybb.o
COBJS-$(CONFIG_MV88E61XX_SWITCH) += mv88e61xx.o
+COBJS-$(CONFIG_PHYLIB) += phy.o
+COBJS-$(CONFIG_PHYLIB_10G) += generic_10g.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --git a/drivers/net/phy/generic_10g.c b/drivers/net/phy/generic_10g.c
new file mode 100644
index 0000000..315c508
--- /dev/null
+++ b/drivers/net/phy/generic_10g.c
@@ -0,0 +1,105 @@
+/*
+ * Generic PHY Management code
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ * Based loosely off of Linux's PHY Lib
+ */
+
+#include <config.h>
+#include <common.h>
+#include <miiphy.h>
+#include <phy.h>
+
+int gen10g_shutdown(struct phy_device *phydev)
+{
+ return 0;
+}
+
+int gen10g_startup(struct phy_device *phydev)
+{
+ int devad, reg;
+ u32 mmd_mask = phydev->mmds;
+
+ phydev->link = 1;
+
+ /* For now just lie and say it's 10G all the time */
+ phydev->speed = SPEED_10000;
+ phydev->duplex = DUPLEX_FULL;
+
+ for (devad = 0; mmd_mask; devad++, mmd_mask = mmd_mask >> 1) {
+ if (!mmd_mask & 1)
+ continue;
+
+ /* Read twice because link state is latched and a
+ * read moves the current state into the register */
+ phy_read(phydev, devad, MDIO_STAT1);
+ reg = phy_read(phydev, devad, MDIO_STAT1);
+ if (reg < 0 || !(reg & MDIO_STAT1_LSTATUS))
+ phydev->link = 0;
+ }
+
+ return 0;
+}
+
+int gen10g_discover_mmds(struct phy_device *phydev)
+{
+ int mmd, stat2, devs1, devs2;
+
+ /* Assume PHY must have at least one of PMA/PMD, WIS, PCS, PHY
+ * XS or DTE XS; give up if none is present. */
+ for (mmd = 1; mmd <= 5; mmd++) {
+ /* Is this MMD present? */
+ stat2 = phy_read(phydev, mmd, MDIO_STAT2);
+ if (stat2 < 0 ||
+ (stat2 & MDIO_STAT2_DEVPRST) != MDIO_STAT2_DEVPRST_VAL)
+ continue;
+
+ /* It should tell us about all the other MMDs */
+ devs1 = phy_read(phydev, mmd, MDIO_DEVS1);
+ devs2 = phy_read(phydev, mmd, MDIO_DEVS2);
+ if (devs1 < 0 || devs2 < 0)
+ continue;
+
+ phydev->mmds = devs1 | (devs2 << 16);
+ return 0;
+ }
+
+ return 0;
+}
+
+int gen10g_config(struct phy_device *phydev)
+{
+ /* For now, assume 10000baseT. Fill in later */
+ phydev->supported = phydev->advertising = SUPPORTED_10000baseT_Full;
+
+ return gen10g_discover_mmds(phydev);
+}
+
+struct phy_driver gen10g_driver = {
+ .uid = 0xffffffff,
+ .mask = 0xffffffff,
+ .name = "Generic 10G PHY",
+ .features = 0,
+ .config = gen10g_config,
+ .startup = gen10g_startup,
+ .shutdown = gen10g_shutdown,
+};
+
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
new file mode 100644
index 0000000..919011d
--- /dev/null
+++ b/drivers/net/phy/phy.c
@@ -0,0 +1,724 @@
+/*
+ * Generic PHY Management code
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * author Andy Fleming
+ *
+ * Based loosely off of Linux's PHY Lib
+ */
+
+#include <config.h>
+#include <common.h>
+#include <malloc.h>
+#include <net.h>
+#include <command.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <errno.h>
+
+/* Generic PHY support and helper functions */
+
+/**
+ * genphy_config_advert - sanitize and advertise auto-negotation parameters
+ * @phydev: target phy_device struct
+ *
+ * Description: Writes MII_ADVERTISE with the appropriate values,
+ * after sanitizing the values to make sure we only advertise
+ * what is supported. Returns < 0 on error, 0 if the PHY's advertisement
+ * hasn't changed, and > 0 if it has changed.
+ */
+int genphy_config_advert(struct phy_device *phydev)
+{
+ u32 advertise;
+ int oldadv, adv;
+ int err, changed = 0;
+
+ /* Only allow advertising what
+ * this PHY supports */
+ phydev->advertising &= phydev->supported;
+ advertise = phydev->advertising;
+
+ /* Setup standard advertisement */
+ oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE);
+
+ if (adv < 0)
+ return adv;
+
+ adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP |
+ ADVERTISE_PAUSE_ASYM);
+ if (advertise & ADVERTISED_10baseT_Half)
+ adv |= ADVERTISE_10HALF;
+ if (advertise & ADVERTISED_10baseT_Full)
+ adv |= ADVERTISE_10FULL;
+ if (advertise & ADVERTISED_100baseT_Half)
+ adv |= ADVERTISE_100HALF;
+ if (advertise & ADVERTISED_100baseT_Full)
+ adv |= ADVERTISE_100FULL;
+ if (advertise & ADVERTISED_Pause)
+ adv |= ADVERTISE_PAUSE_CAP;
+ if (advertise & ADVERTISED_Asym_Pause)
+ adv |= ADVERTISE_PAUSE_ASYM;
+
+ if (adv != oldadv) {
+ err = phy_write(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE, adv);
+
+ if (err < 0)
+ return err;
+ changed = 1;
+ }
+
+ /* Configure gigabit if it's supported */
+ if (phydev->supported & (SUPPORTED_1000baseT_Half |
+ SUPPORTED_1000baseT_Full)) {
+ oldadv = adv = phy_read(phydev, MDIO_DEVAD_NONE, MII_CTRL1000);
+
+ if (adv < 0)
+ return adv;
+
+ adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
+ if (advertise & SUPPORTED_1000baseT_Half)
+ adv |= ADVERTISE_1000HALF;
+ if (advertise & SUPPORTED_1000baseT_Full)
+ adv |= ADVERTISE_1000FULL;
+
+ if (adv != oldadv) {
+ err = phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000,
+ adv);
+
+ if (err < 0)
+ return err;
+ changed = 1;
+ }
+ }
+
+ return changed;
+}
+
+
+/**
+ * genphy_setup_forced - configures/forces speed/duplex from @phydev
+ * @phydev: target phy_device struct
+ *
+ * Description: Configures MII_BMCR to force speed/duplex
+ * to the values in phydev. Assumes that the values are valid.
+ */
+int genphy_setup_forced(struct phy_device *phydev)
+{
+ int err;
+ int ctl = 0;
+
+ phydev->pause = phydev->asym_pause = 0;
+
+ if (SPEED_1000 == phydev->speed)
+ ctl |= BMCR_SPEED1000;
+ else if (SPEED_100 == phydev->speed)
+ ctl |= BMCR_SPEED100;
+
+ if (DUPLEX_FULL == phydev->duplex)
+ ctl |= BMCR_FULLDPLX;
+
+ err = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl);
+
+ return err;
+}
+
+
+/**
+ * genphy_restart_aneg - Enable and Restart Autonegotiation
+ * @phydev: target phy_device struct
+ */
+int genphy_restart_aneg(struct phy_device *phydev)
+{
+ int ctl;
+
+ ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+ if (ctl < 0)
+ return ctl;
+
+ ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
+
+ /* Don't isolate the PHY if we're negotiating */
+ ctl &= ~(BMCR_ISOLATE);
+
+ ctl = phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, ctl);
+
+ return ctl;
+}
+
+
+/**
+ * genphy_config_aneg - restart auto-negotiation or write BMCR
+ * @phydev: target phy_device struct
+ *
+ * Description: If auto-negotiation is enabled, we configure the
+ * advertising, and then restart auto-negotiation. If it is not
+ * enabled, then we write the BMCR.
+ */
+int genphy_config_aneg(struct phy_device *phydev)
+{
+ int result;
+
+ if (AUTONEG_ENABLE != phydev->autoneg)
+ return genphy_setup_forced(phydev);
+
+ result = genphy_config_advert(phydev);
+
+ if (result < 0) /* error */
+ return result;
+
+ if (result == 0) {
+ /* Advertisment hasn't changed, but maybe aneg was never on to
+ * begin with? Or maybe phy was isolated? */
+ int ctl = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+ if (ctl < 0)
+ return ctl;
+
+ if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE))
+ result = 1; /* do restart aneg */
+ }
+
+ /* Only restart aneg if we are advertising something different
+ * than we were before. */
+ if (result > 0)
+ result = genphy_restart_aneg(phydev);
+
+ return result;
+}
+
+/**
+ * genphy_update_link - update link status in @phydev
+ * @phydev: target phy_device struct
+ *
+ * Description: Update the value in phydev->link to reflect the
+ * current link value. In order to do this, we need to read
+ * the status register twice, keeping the second value.
+ */
+int genphy_update_link(struct phy_device *phydev)
+{
+ unsigned int mii_reg;
+
+ /*
+ * Wait if the link is up, and autonegotiation is in progress
+ * (ie - we're capable and it's not done)
+ */
+ mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+ /*
+ * If we already saw the link up, and it hasn't gone down, then
+ * we don't need to wait for autoneg again
+ */
+ if (phydev->link && mii_reg & BMSR_LSTATUS)
+ return 0;
+
+ if ((mii_reg & BMSR_ANEGCAPABLE) && !(mii_reg & BMSR_ANEGCOMPLETE)) {
+ int i = 0;
+
+ printf("%s Waiting for PHY auto negotiation to complete",
+ phydev->dev->name);
+ while (!(mii_reg & BMSR_ANEGCOMPLETE)) {
+ /*
+ * Timeout reached ?
+ */
+ if (i > PHY_ANEG_TIMEOUT) {
+ printf(" TIMEOUT !\n");
+ phydev->link = 0;
+ return 0;
+ }
+
+ if (ctrlc()) {
+ puts("user interrupt!\n");
+ phydev->link = 0;
+ return -EINTR;
+ }
+
+ if ((i++ % 500) == 0)
+ printf(".");
+
+ udelay(1000); /* 1 ms */
+ mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+ }
+ printf(" done\n");
+ phydev->link = 1;
+ } else {
+ /* Read the link a second time to clear the latched state */
+ mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+ if (mii_reg & BMSR_LSTATUS)
+ phydev->link = 1;
+ else
+ phydev->link = 0;
+ }
+
+ return 0;
+}
+
+/*
+ * Generic function which updates the speed and duplex. If
+ * autonegotiation is enabled, it uses the AND of the link
+ * partner's advertised capabilities and our advertised
+ * capabilities. If autonegotiation is disabled, we use the
+ * appropriate bits in the control register.
+ *
+ * Stolen from Linux's mii.c and phy_device.c
+ */
+static int genphy_parse_link(struct phy_device *phydev)
+{
+ int mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+ /* We're using autonegotiation */
+ if (mii_reg & BMSR_ANEGCAPABLE) {
+ u32 lpa = 0;
+ u32 gblpa = 0;
+
+ /* Check for gigabit capability */
+ if (mii_reg & BMSR_ERCAP) {
+ /* We want a list of states supported by
+ * both PHYs in the link
+ */
+ gblpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_STAT1000);
+ gblpa &= phy_read(phydev,
+ MDIO_DEVAD_NONE, MII_CTRL1000) << 2;
+ }
+
+ /* Set the baseline so we only have to set them
+ * if they're different
+ */
+ phydev->speed = SPEED_10;
+ phydev->duplex = DUPLEX_HALF;
+
+ /* Check the gigabit fields */
+ if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
+ phydev->speed = SPEED_1000;
+
+ if (gblpa & PHY_1000BTSR_1000FD)
+ phydev->duplex = DUPLEX_FULL;
+
+ /* We're done! */
+ return 0;
+ }
+
+ lpa = phy_read(phydev, MDIO_DEVAD_NONE, MII_ADVERTISE);
+ lpa &= phy_read(phydev, MDIO_DEVAD_NONE, MII_LPA);
+
+ if (lpa & (LPA_100FULL | LPA_100HALF)) {
+ phydev->speed = SPEED_100;
+
+ if (lpa & LPA_100FULL)
+ phydev->duplex = DUPLEX_FULL;
+
+ } else if (lpa & LPA_10FULL)
+ phydev->duplex = DUPLEX_FULL;
+ } else {
+ u32 bmcr = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+ phydev->speed = SPEED_10;
+ phydev->duplex = DUPLEX_HALF;
+
+ if (bmcr & BMCR_FULLDPLX)
+ phydev->duplex = DUPLEX_FULL;
+
+ if (bmcr & BMCR_SPEED1000)
+ phydev->speed = SPEED_1000;
+ else if (bmcr & BMCR_SPEED100)
+ phydev->speed = SPEED_100;
+ }
+
+ return 0;
+}
+
+int genphy_config(struct phy_device *phydev)
+{
+ int val;
+ u32 features;
+
+ /* For now, I'll claim that the generic driver supports
+ * all possible port types */
+ features = (SUPPORTED_TP | SUPPORTED_MII
+ | SUPPORTED_AUI | SUPPORTED_FIBRE |
+ SUPPORTED_BNC);
+
+ /* Do we support autonegotiation? */
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMSR);
+
+ if (val < 0)
+ return val;
+
+ if (val & BMSR_ANEGCAPABLE)
+ features |= SUPPORTED_Autoneg;
+
+ if (val & BMSR_100FULL)
+ features |= SUPPORTED_100baseT_Full;
+ if (val & BMSR_100HALF)
+ features |= SUPPORTED_100baseT_Half;
+ if (val & BMSR_10FULL)
+ features |= SUPPORTED_10baseT_Full;
+ if (val & BMSR_10HALF)
+ features |= SUPPORTED_10baseT_Half;
+
+ if (val & BMSR_ESTATEN) {
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MII_ESTATUS);
+
+ if (val < 0)
+ return val;
+
+ if (val & ESTATUS_1000_TFULL)
+ features |= SUPPORTED_1000baseT_Full;
+ if (val & ESTATUS_1000_THALF)
+ features |= SUPPORTED_1000baseT_Half;
+ }
+
+ phydev->supported = features;
+ phydev->advertising = features;
+
+ genphy_config_aneg(phydev);
+
+ return 0;
+}
+
+int genphy_startup(struct phy_device *phydev)
+{
+ genphy_update_link(phydev);
+ genphy_parse_link(phydev);
+
+ return 0;
+}
+
+int genphy_shutdown(struct phy_device *phydev)
+{
+ return 0;
+}
+
+static struct phy_driver genphy_driver = {
+ .uid = 0xffffffff,
+ .mask = 0xffffffff,
+ .name = "Generic PHY",
+ .features = 0,
+ .config = genphy_config,
+ .startup = genphy_startup,
+ .shutdown = genphy_shutdown,
+};
+
+static LIST_HEAD(phy_drivers);
+
+int phy_init(void)
+{
+ return 0;
+}
+
+int phy_register(struct phy_driver *drv)
+{
+ INIT_LIST_HEAD(&drv->list);
+ list_add_tail(&drv->list, &phy_drivers);
+
+ return 0;
+}
+
+int phy_probe(struct phy_device *phydev)
+{
+ int err = 0;
+
+ phydev->advertising = phydev->supported = phydev->drv->features;
+ phydev->mmds = phydev->drv->mmds;
+
+ if (phydev->drv->probe)
+ err = phydev->drv->probe(phydev);
+
+ return err;
+}
+
+static struct phy_driver *generic_for_interface(phy_interface_t interface)
+{
+#ifdef CONFIG_PHYLIB_10G
+ if (is_10g_interface(interface))
+ return &gen10g_driver;
+#endif
+
+ return &genphy_driver;
+}
+
+struct phy_driver *get_phy_driver(struct phy_device *phydev,
+ phy_interface_t interface)
+{
+ struct list_head *entry;
+ int phy_id = phydev->phy_id;
+ struct phy_driver *drv = NULL;
+
+ list_for_each(entry, &phy_drivers) {
+ drv = list_entry(entry, struct phy_driver, list);
+ if ((drv->uid & drv->mask) == (phy_id & drv->mask))
+ return drv;
+ }
+
+ /* If we made it here, there's no driver for this PHY */
+ return generic_for_interface(interface);
+}
+
+struct phy_device *phy_device_create(struct mii_dev *bus, int addr, int phy_id,
+ phy_interface_t interface)
+{
+ struct phy_device *dev;
+
+ /* We allocate the device, and initialize the
+ * default values */
+ dev = malloc(sizeof(*dev));
+ if (!dev) {
+ printf("Failed to allocate PHY device for %s:%d\n",
+ bus->name, addr);
+ return NULL;
+ }
+
+ memset(dev, 0, sizeof(*dev));
+
+ dev->duplex = -1;
+ dev->link = 1;
+ dev->interface = interface;
+
+ dev->autoneg = AUTONEG_ENABLE;
+
+ dev->addr = addr;
+ dev->phy_id = phy_id;
+ dev->bus = bus;
+
+ dev->drv = get_phy_driver(dev, interface);
+
+ phy_probe(dev);
+
+ bus->phymap[addr] = dev;
+
+ return dev;
+}
+
+/**
+ * get_phy_id - reads the specified addr for its ID.
+ * @bus: the target MII bus
+ * @addr: PHY address on the MII bus
+ * @phy_id: where to store the ID retrieved.
+ *
+ * Description: Reads the ID registers of the PHY at @addr on the
+ * @bus, stores it in @phy_id and returns zero on success.
+ */
+int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
+{
+ int phy_reg;
+
+ /* Grab the bits from PHYIR1, and put them
+ * in the upper half */
+ phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
+
+ if (phy_reg < 0)
+ return -EIO;
+
+ *phy_id = (phy_reg & 0xffff) << 16;
+
+ /* Grab the bits from PHYIR2, and put them in the lower half */
+ phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
+
+ if (phy_reg < 0)
+ return -EIO;
+
+ *phy_id |= (phy_reg & 0xffff);
+
+ return 0;
+}
+
+/**
+ * get_phy_device - reads the specified PHY device and returns its @phy_device struct
+ * @bus: the target MII bus
+ * @addr: PHY address on the MII bus
+ *
+ * Description: Reads the ID registers of the PHY at @addr on the
+ * @bus, then allocates and returns the phy_device to represent it.
+ */
+struct phy_device *get_phy_device(struct mii_dev *bus, int addr,
+ phy_interface_t interface)
+{
+ u32 phy_id = 0x1fffffff;
+ int i;
+ int r;
+
+ /* If we have one, return the existing device, with new interface */
+ if (bus->phymap[addr]) {
+ bus->phymap[addr]->interface = interface;
+
+ return bus->phymap[addr];
+ }
+
+ /* Try Standard (ie Clause 22) access */
+ r = get_phy_id(bus, addr, MDIO_DEVAD_NONE, &phy_id);
+ if (r)
+ return NULL;
+
+ /* If the PHY ID is mostly f's, we didn't find anything */
+ if ((phy_id & 0x1fffffff) != 0x1fffffff)
+ return phy_device_create(bus, addr, phy_id, interface);
+
+ /* Otherwise we have to try Clause 45 */
+ for (i = 1; i < 5; i++) {
+ r = get_phy_id(bus, addr, i, &phy_id);
+ if (r)
+ return NULL;
+
+ /* If the phy_id is mostly Fs, there is no device there */
+ if ((phy_id & 0x1fffffff) != 0x1fffffff)
+ break;
+ }
+
+ return phy_device_create(bus, addr, phy_id, interface);
+}
+
+int phy_reset(struct phy_device *phydev)
+{
+ int reg;
+ int timeout = 500;
+ int devad = MDIO_DEVAD_NONE;
+
+#ifdef CONFIG_PHYLIB_10G
+ /* If it's 10G, we need to issue reset through one of the MMDs */
+ if (is_10g_interface(phydev->interface)) {
+ if (!phydev->mmds)
+ gen10g_discover_mmds(phydev);
+
+ devad = ffs(phydev->mmds) - 1;
+ }
+#endif
+
+ reg = phy_read(phydev, devad, MII_BMCR);
+ if (reg < 0) {
+ debug("PHY status read failed\n");
+ return -1;
+ }
+
+ reg |= BMCR_RESET;
+
+ if (phy_write(phydev, devad, MII_BMCR, reg) < 0) {
+ debug("PHY reset failed\n");
+ return -1;
+ }
+
+#ifdef CONFIG_PHY_RESET_DELAY
+ udelay(CONFIG_PHY_RESET_DELAY); /* Intel LXT971A needs this */
+#endif
+ /*
+ * Poll the control register for the reset bit to go to 0 (it is
+ * auto-clearing). This should happen within 0.5 seconds per the
+ * IEEE spec.
+ */
+ while ((reg & BMCR_RESET) && timeout--) {
+ reg = phy_read(phydev, devad, MII_BMCR);
+
+ if (reg < 0) {
+ debug("PHY status read failed\n");
+ return -1;
+ }
+ udelay(1000);
+ }
+
+ if (reg & BMCR_RESET) {
+ puts("PHY reset timed out\n");
+ return -1;
+ }
+
+ return 0;
+}
+
+int miiphy_reset(const char *devname, unsigned char addr)
+{
+ struct mii_dev *bus = miiphy_get_dev_by_name(devname);
+ struct phy_device *phydev;
+
+ /*
+ * miiphy_reset was only used on standard PHYs, so we'll fake it here.
+ * If later code tries to connect with the right interface, this will
+ * be corrected by get_phy_device in phy_connect()
+ */
+ phydev = get_phy_device(bus, addr, PHY_INTERFACE_MODE_MII);
+
+ return phy_reset(phydev);
+}
+
+struct phy_device *phy_connect(struct mii_dev *bus, int addr,
+ struct eth_device *dev,
+ phy_interface_t interface)
+{
+ struct phy_device *phydev;
+
+ /* Reset the bus */
+ bus->reset(bus);
+
+ /* Wait 15ms to make sure the PHY has come out of hard reset */
+ udelay(15000);
+
+ phydev = get_phy_device(bus, addr, interface);
+
+ if (!phydev) {
+ printf("Could not get PHY for %s:%d\n", bus->name, addr);
+
+ return NULL;
+ }
+
+ /* Soft Reset the PHY */
+ phy_reset(phydev);
+
+ if (phydev->dev)
+ printf("%s:%d is connected to %s. Reconnecting to %s\n",
+ bus->name, addr, phydev->dev->name, dev->name);
+
+ phydev->dev = dev;
+
+ printf("%s connected to %s\n", dev->name, phydev->drv->name);
+
+ return phydev;
+}
+
+int phy_startup(struct phy_device *phydev)
+{
+ if (phydev->drv->startup)
+ phydev->drv->startup(phydev);
+
+ return 0;
+}
+
+static int __board_phy_config(struct phy_device *phydev)
+{
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+ __attribute__((weak, alias("__board_phy_config")));
+
+int phy_config(struct phy_device *phydev)
+{
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ /* Invoke an optional board-specific helper */
+ board_phy_config(phydev);
+
+ return 0;
+}
+
+int phy_shutdown(struct phy_device *phydev)
+{
+ if (phydev->drv->shutdown)
+ phydev->drv->shutdown(phydev);
+
+ return 0;
+}
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
new file mode 100644
index 0000000..fcb20fe
--- /dev/null
+++ b/include/linux/ethtool.h
@@ -0,0 +1,721 @@
+/*
+ * ethtool.h: Defines for Linux ethtool.
+ *
+ * Copyright (C) 1998 David S. Miller (davem@redhat.com)
+ * Copyright 2001 Jeff Garzik <jgarzik@pobox.com>
+ * Portions Copyright 2001 Sun Microsystems (thockin@sun.com)
+ * Portions Copyright 2002 Intel (eli.kupermann@intel.com,
+ * christopher.leech@intel.com,
+ * scott.feldman@intel.com)
+ * Portions Copyright (C) Sun Microsystems 2008
+ */
+
+#ifndef _LINUX_ETHTOOL_H
+#define _LINUX_ETHTOOL_H
+
+#include <linux/types.h>
+
+/* This should work for both 32 and 64 bit userland. */
+struct ethtool_cmd {
+ __u32 cmd;
+ __u32 supported; /* Features this interface supports */
+ __u32 advertising; /* Features this interface advertises */
+ __u16 speed; /* The forced speed, 10Mb, 100Mb, gigabit */
+ __u8 duplex; /* Duplex, half or full */
+ __u8 port; /* Which connector port */
+ __u8 phy_address;
+ __u8 transceiver; /* Which transceiver to use */
+ __u8 autoneg; /* Enable or disable autonegotiation */
+ __u8 mdio_support;
+ __u32 maxtxpkt; /* Tx pkts before generating tx int */
+ __u32 maxrxpkt; /* Rx pkts before generating rx int */
+ __u16 speed_hi;
+ __u8 eth_tp_mdix;
+ __u8 reserved2;
+ __u32 lp_advertising; /* Features the link partner advertises */
+ __u32 reserved[2];
+};
+
+static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep,
+ __u32 speed)
+{
+
+ ep->speed = (__u16)speed;
+ ep->speed_hi = (__u16)(speed >> 16);
+}
+
+static inline __u32 ethtool_cmd_speed(struct ethtool_cmd *ep)
+{
+ return (ep->speed_hi << 16) | ep->speed;
+}
+
+#define ETHTOOL_FWVERS_LEN 32
+#define ETHTOOL_BUSINFO_LEN 32
+/* these strings are set to whatever the driver author decides... */
+struct ethtool_drvinfo {
+ __u32 cmd;
+ char driver[32]; /* driver short name, "tulip", "eepro100" */
+ char version[32]; /* driver version string */
+ char fw_version[ETHTOOL_FWVERS_LEN]; /* firmware version string */
+ char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */
+ /* For PCI devices, use pci_name(pci_dev). */
+ char reserved1[32];
+ char reserved2[12];
+ /*
+ * Some struct members below are filled in
+ * using ops->get_sset_count(). Obtaining
+ * this info from ethtool_drvinfo is now
+ * deprecated; Use ETHTOOL_GSSET_INFO
+ * instead.
+ */
+ __u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */
+ __u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */
+ __u32 testinfo_len;
+ __u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */
+ __u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */
+};
+
+#define SOPASS_MAX 6
+/* wake-on-lan settings */
+struct ethtool_wolinfo {
+ __u32 cmd;
+ __u32 supported;
+ __u32 wolopts;
+ __u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */
+};
+
+/* for passing single values */
+struct ethtool_value {
+ __u32 cmd;
+ __u32 data;
+};
+
+/* for passing big chunks of data */
+struct ethtool_regs {
+ __u32 cmd;
+ __u32 version; /* driver-specific, indicates different chips/revs */
+ __u32 len; /* bytes */
+ __u8 data[0];
+};
+
+/* for passing EEPROM chunks */
+struct ethtool_eeprom {
+ __u32 cmd;
+ __u32 magic;
+ __u32 offset; /* in bytes */
+ __u32 len; /* in bytes */
+ __u8 data[0];
+};
+
+/* for configuring coalescing parameters of chip */
+struct ethtool_coalesce {
+ __u32 cmd; /* ETHTOOL_{G,S}COALESCE */
+
+ /* How many usecs to delay an RX interrupt after
+ * a packet arrives. If 0, only rx_max_coalesced_frames
+ * is used.
+ */
+ __u32 rx_coalesce_usecs;
+
+ /* How many packets to delay an RX interrupt after
+ * a packet arrives. If 0, only rx_coalesce_usecs is
+ * used. It is illegal to set both usecs and max frames
+ * to zero as this would cause RX interrupts to never be
+ * generated.
+ */
+ __u32 rx_max_coalesced_frames;
+
+ /* Same as above two parameters, except that these values
+ * apply while an IRQ is being serviced by the host. Not
+ * all cards support this feature and the values are ignored
+ * in that case.
+ */
+ __u32 rx_coalesce_usecs_irq;
+ __u32 rx_max_coalesced_frames_irq;
+
+ /* How many usecs to delay a TX interrupt after
+ * a packet is sent. If 0, only tx_max_coalesced_frames
+ * is used.
+ */
+ __u32 tx_coalesce_usecs;
+
+ /* How many packets to delay a TX interrupt after
+ * a packet is sent. If 0, only tx_coalesce_usecs is
+ * used. It is illegal to set both usecs and max frames
+ * to zero as this would cause TX interrupts to never be
+ * generated.
+ */
+ __u32 tx_max_coalesced_frames;
+
+ /* Same as above two parameters, except that these values
+ * apply while an IRQ is being serviced by the host. Not
+ * all cards support this feature and the values are ignored
+ * in that case.
+ */
+ __u32 tx_coalesce_usecs_irq;
+ __u32 tx_max_coalesced_frames_irq;
+
+ /* How many usecs to delay in-memory statistics
+ * block updates. Some drivers do not have an in-memory
+ * statistic block, and in such cases this value is ignored.
+ * This value must not be zero.
+ */
+ __u32 stats_block_coalesce_usecs;
+
+ /* Adaptive RX/TX coalescing is an algorithm implemented by
+ * some drivers to improve latency under low packet rates and
+ * improve throughput under high packet rates. Some drivers
+ * only implement one of RX or TX adaptive coalescing. Anything
+ * not implemented by the driver causes these values to be
+ * silently ignored.
+ */
+ __u32 use_adaptive_rx_coalesce;
+ __u32 use_adaptive_tx_coalesce;
+
+ /* When the packet rate (measured in packets per second)
+ * is below pkt_rate_low, the {rx,tx}_*_low parameters are
+ * used.
+ */
+ __u32 pkt_rate_low;
+ __u32 rx_coalesce_usecs_low;
+ __u32 rx_max_coalesced_frames_low;
+ __u32 tx_coalesce_usecs_low;
+ __u32 tx_max_coalesced_frames_low;
+
+ /* When the packet rate is below pkt_rate_high but above
+ * pkt_rate_low (both measured in packets per second) the
+ * normal {rx,tx}_* coalescing parameters are used.
+ */
+
+ /* When the packet rate is (measured in packets per second)
+ * is above pkt_rate_high, the {rx,tx}_*_high parameters are
+ * used.
+ */
+ __u32 pkt_rate_high;
+ __u32 rx_coalesce_usecs_high;
+ __u32 rx_max_coalesced_frames_high;
+ __u32 tx_coalesce_usecs_high;
+ __u32 tx_max_coalesced_frames_high;
+
+ /* How often to do adaptive coalescing packet rate sampling,
+ * measured in seconds. Must not be zero.
+ */
+ __u32 rate_sample_interval;
+};
+
+/* for configuring RX/TX ring parameters */
+struct ethtool_ringparam {
+ __u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */
+
+ /* Read only attributes. These indicate the maximum number
+ * of pending RX/TX ring entries the driver will allow the
+ * user to set.
+ */
+ __u32 rx_max_pending;
+ __u32 rx_mini_max_pending;
+ __u32 rx_jumbo_max_pending;
+ __u32 tx_max_pending;
+
+ /* Values changeable by the user. The valid values are
+ * in the range 1 to the "*_max_pending" counterpart above.
+ */
+ __u32 rx_pending;
+ __u32 rx_mini_pending;
+ __u32 rx_jumbo_pending;
+ __u32 tx_pending;
+};
+
+/* for configuring link flow control parameters */
+struct ethtool_pauseparam {
+ __u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */
+
+ /* If the link is being auto-negotiated (via ethtool_cmd.autoneg
+ * being true) the user may set 'autonet' here non-zero to have the
+ * pause parameters be auto-negotiated too. In such a case, the
+ * {rx,tx}_pause values below determine what capabilities are
+ * advertised.
+ *
+ * If 'autoneg' is zero or the link is not being auto-negotiated,
+ * then {rx,tx}_pause force the driver to use/not-use pause
+ * flow control.
+ */
+ __u32 autoneg;
+ __u32 rx_pause;
+ __u32 tx_pause;
+};
+
+#define ETH_GSTRING_LEN 32
+enum ethtool_stringset {
+ ETH_SS_TEST = 0,
+ ETH_SS_STATS,
+ ETH_SS_PRIV_FLAGS,
+ ETH_SS_NTUPLE_FILTERS,
+ ETH_SS_FEATURES,
+};
+
+/* for passing string sets for data tagging */
+struct ethtool_gstrings {
+ __u32 cmd; /* ETHTOOL_GSTRINGS */
+ __u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/
+ __u32 len; /* number of strings in the string set */
+ __u8 data[0];
+};
+
+struct ethtool_sset_info {
+ __u32 cmd; /* ETHTOOL_GSSET_INFO */
+ __u32 reserved;
+ __u64 sset_mask; /* input: each bit selects an sset to query */
+ /* output: each bit a returned sset */
+ __u32 data[0]; /* ETH_SS_xxx count, in order, based on bits
+ in sset_mask. One bit implies one
+ __u32, two bits implies two
+ __u32's, etc. */
+};
+
+enum ethtool_test_flags {
+ ETH_TEST_FL_OFFLINE = (1 << 0), /* online / offline */
+ ETH_TEST_FL_FAILED = (1 << 1), /* test passed / failed */
+};
+
+/* for requesting NIC test and getting results*/
+struct ethtool_test {
+ __u32 cmd; /* ETHTOOL_TEST */
+ __u32 flags; /* ETH_TEST_FL_xxx */
+ __u32 reserved;
+ __u32 len; /* result length, in number of u64 elements */
+ __u64 data[0];
+};
+
+/* for dumping NIC-specific statistics */
+struct ethtool_stats {
+ __u32 cmd; /* ETHTOOL_GSTATS */
+ __u32 n_stats; /* number of u64's being returned */
+ __u64 data[0];
+};
+
+struct ethtool_perm_addr {
+ __u32 cmd; /* ETHTOOL_GPERMADDR */
+ __u32 size;
+ __u8 data[0];
+};
+
+/* boolean flags controlling per-interface behavior characteristics.
+ * When reading, the flag indicates whether or not a certain behavior
+ * is enabled/present. When writing, the flag indicates whether
+ * or not the driver should turn on (set) or off (clear) a behavior.
+ *
+ * Some behaviors may read-only (unconditionally absent or present).
+ * If such is the case, return EINVAL in the set-flags operation if the
+ * flag differs from the read-only value.
+ */
+enum ethtool_flags {
+ ETH_FLAG_TXVLAN = (1 << 7), /* TX VLAN offload enabled */
+ ETH_FLAG_RXVLAN = (1 << 8), /* RX VLAN offload enabled */
+ ETH_FLAG_LRO = (1 << 15), /* LRO is enabled */
+ ETH_FLAG_NTUPLE = (1 << 27), /* N-tuple filters enabled */
+ ETH_FLAG_RXHASH = (1 << 28),
+};
+
+/* The following structures are for supporting RX network flow
+ * classification and RX n-tuple configuration. Note, all multibyte
+ * fields, e.g., ip4src, ip4dst, psrc, pdst, spi, etc. are expected to
+ * be in network byte order.
+ */
+
+/**
+ * struct ethtool_tcpip4_spec - flow specification for TCP/IPv4 etc.
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @psrc: Source port
+ * @pdst: Destination port
+ * @tos: Type-of-service
+ *
+ * This can be used to specify a TCP/IPv4, UDP/IPv4 or SCTP/IPv4 flow.
+ */
+struct ethtool_tcpip4_spec {
+ __be32 ip4src;
+ __be32 ip4dst;
+ __be16 psrc;
+ __be16 pdst;
+ __u8 tos;
+};
+
+/**
+ * struct ethtool_ah_espip4_spec - flow specification for IPsec/IPv4
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @spi: Security parameters index
+ * @tos: Type-of-service
+ *
+ * This can be used to specify an IPsec transport or tunnel over IPv4.
+ */
+struct ethtool_ah_espip4_spec {
+ __be32 ip4src;
+ __be32 ip4dst;
+ __be32 spi;
+ __u8 tos;
+};
+
+#define ETH_RX_NFC_IP4 1
+
+/**
+ * struct ethtool_usrip4_spec - general flow specification for IPv4
+ * @ip4src: Source host
+ * @ip4dst: Destination host
+ * @l4_4_bytes: First 4 bytes of transport (layer 4) header
+ * @tos: Type-of-service
+ * @ip_ver: Value must be %ETH_RX_NFC_IP4; mask must be 0
+ * @proto: Transport protocol number; mask must be 0
+ */
+struct ethtool_usrip4_spec {
+ __be32 ip4src;
+ __be32 ip4dst;
+ __be32 l4_4_bytes;
+ __u8 tos;
+ __u8 ip_ver;
+ __u8 proto;
+};
+
+
+/**
+ * struct ethtool_rxfh_indir - command to get or set RX flow hash indirection
+ * @cmd: Specific command number - %ETHTOOL_GRXFHINDIR or %ETHTOOL_SRXFHINDIR
+ * @size: On entry, the array size of the user buffer. On return from
+ * %ETHTOOL_GRXFHINDIR, the array size of the hardware indirection table.
+ * @ring_index: RX ring/queue index for each hash value
+ */
+struct ethtool_rxfh_indir {
+ __u32 cmd;
+ __u32 size;
+ __u32 ring_index[0];
+};
+
+#define ETHTOOL_FLASH_MAX_FILENAME 128
+enum ethtool_flash_op_type {
+ ETHTOOL_FLASH_ALL_REGIONS = 0,
+};
+
+/* for passing firmware flashing related parameters */
+struct ethtool_flash {
+ __u32 cmd;
+ __u32 region;
+ char data[ETHTOOL_FLASH_MAX_FILENAME];
+};
+
+/* for returning and changing feature sets */
+
+/**
+ * struct ethtool_get_features_block - block with state of 32 features
+ * @available: mask of changeable features
+ * @requested: mask of features requested to be enabled if possible
+ * @active: mask of currently enabled features
+ * @never_changed: mask of features not changeable for any device
+ */
+struct ethtool_get_features_block {
+ __u32 available;
+ __u32 requested;
+ __u32 active;
+ __u32 never_changed;
+};
+
+/**
+ * struct ethtool_gfeatures - command to get state of device's features
+ * @cmd: command number = %ETHTOOL_GFEATURES
+ * @size: in: number of elements in the features[] array;
+ * out: number of elements in features[] needed to hold all features
+ * @features: state of features
+ */
+struct ethtool_gfeatures {
+ __u32 cmd;
+ __u32 size;
+ struct ethtool_get_features_block features[0];
+};
+
+/**
+ * struct ethtool_set_features_block - block with request for 32 features
+ * @valid: mask of features to be changed
+ * @requested: values of features to be changed
+ */
+struct ethtool_set_features_block {
+ __u32 valid;
+ __u32 requested;
+};
+
+/**
+ * struct ethtool_sfeatures - command to request change in device's features
+ * @cmd: command number = %ETHTOOL_SFEATURES
+ * @size: array size of the features[] array
+ * @features: feature change masks
+ */
+struct ethtool_sfeatures {
+ __u32 cmd;
+ __u32 size;
+ struct ethtool_set_features_block features[0];
+};
+
+/*
+ * %ETHTOOL_SFEATURES changes features present in features[].valid to the
+ * values of corresponding bits in features[].requested. Bits in .requested
+ * not set in .valid or not changeable are ignored.
+ *
+ * Returns %EINVAL when .valid contains undefined or never-changable bits
+ * or size is not equal to required number of features words (32-bit blocks).
+ * Returns >= 0 if request was completed; bits set in the value mean:
+ * %ETHTOOL_F_UNSUPPORTED - there were bits set in .valid that are not
+ * changeable (not present in %ETHTOOL_GFEATURES' features[].available)
+ * those bits were ignored.
+ * %ETHTOOL_F_WISH - some or all changes requested were recorded but the
+ * resulting state of bits masked by .valid is not equal to .requested.
+ * Probably there are other device-specific constraints on some features
+ * in the set. When %ETHTOOL_F_UNSUPPORTED is set, .valid is considered
+ * here as though ignored bits were cleared.
+ * %ETHTOOL_F_COMPAT - some or all changes requested were made by calling
+ * compatibility functions. Requested offload state cannot be properly
+ * managed by kernel.
+ *
+ * Meaning of bits in the masks are obtained by %ETHTOOL_GSSET_INFO (number of
+ * bits in the arrays - always multiple of 32) and %ETHTOOL_GSTRINGS commands
+ * for ETH_SS_FEATURES string set. First entry in the table corresponds to least
+ * significant bit in features[0] fields. Empty strings mark undefined features.
+ */
+enum ethtool_sfeatures_retval_bits {
+ ETHTOOL_F_UNSUPPORTED__BIT,
+ ETHTOOL_F_WISH__BIT,
+ ETHTOOL_F_COMPAT__BIT,
+};
+
+#define ETHTOOL_F_UNSUPPORTED (1 << ETHTOOL_F_UNSUPPORTED__BIT)
+#define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT)
+#define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT)
+
+/* CMDs currently supported */
+#define ETHTOOL_GSET 0x00000001 /* Get settings. */
+#define ETHTOOL_SSET 0x00000002 /* Set settings. */
+#define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */
+#define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */
+#define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */
+#define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options. */
+#define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */
+#define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level. */
+#define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation. */
+/* Get link status for host, i.e. whether the interface *and* the
+ * physical port (if there is one) are up (ethtool_value). */
+#define ETHTOOL_GLINK 0x0000000a
+#define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */
+#define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data. */
+#define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */
+#define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config. */
+#define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */
+#define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters. */
+#define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */
+#define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters. */
+#define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */
+#define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */
+#define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */
+#define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */
+#define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable
+ * (ethtool_value) */
+#define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable
+ * (ethtool_value). */
+#define ETHTOOL_TEST 0x0000001a /* execute NIC self-test. */
+#define ETHTOOL_GSTRINGS 0x0000001b /* get specified string set */
+#define ETHTOOL_PHYS_ID 0x0000001c /* identify the NIC */
+#define ETHTOOL_GSTATS 0x0000001d /* get NIC-specific statistics */
+#define ETHTOOL_GTSO 0x0000001e /* Get TSO enable (ethtool_value) */
+#define ETHTOOL_STSO 0x0000001f /* Set TSO enable (ethtool_value) */
+#define ETHTOOL_GPERMADDR 0x00000020 /* Get permanent hardware address */
+#define ETHTOOL_GUFO 0x00000021 /* Get UFO enable (ethtool_value) */
+#define ETHTOOL_SUFO 0x00000022 /* Set UFO enable (ethtool_value) */
+#define ETHTOOL_GGSO 0x00000023 /* Get GSO enable (ethtool_value) */
+#define ETHTOOL_SGSO 0x00000024 /* Set GSO enable (ethtool_value) */
+#define ETHTOOL_GFLAGS 0x00000025 /* Get flags bitmap(ethtool_value) */
+#define ETHTOOL_SFLAGS 0x00000026 /* Set flags bitmap(ethtool_value) */
+#define ETHTOOL_GPFLAGS 0x00000027 /* Get driver-private flags bitmap */
+#define ETHTOOL_SPFLAGS 0x00000028 /* Set driver-private flags bitmap */
+
+#define ETHTOOL_GRXFH 0x00000029 /* Get RX flow hash configuration */
+#define ETHTOOL_SRXFH 0x0000002a /* Set RX flow hash configuration */
+#define ETHTOOL_GGRO 0x0000002b /* Get GRO enable (ethtool_value) */
+#define ETHTOOL_SGRO 0x0000002c /* Set GRO enable (ethtool_value) */
+#define ETHTOOL_GRXRINGS 0x0000002d /* Get RX rings available for LB */
+#define ETHTOOL_GRXCLSRLCNT 0x0000002e /* Get RX class rule count */
+#define ETHTOOL_GRXCLSRULE 0x0000002f /* Get RX classification rule */
+#define ETHTOOL_GRXCLSRLALL 0x00000030 /* Get all RX classification rule */
+#define ETHTOOL_SRXCLSRLDEL 0x00000031 /* Delete RX classification rule */
+#define ETHTOOL_SRXCLSRLINS 0x00000032 /* Insert RX classification rule */
+#define ETHTOOL_FLASHDEV 0x00000033 /* Flash firmware to device */
+#define ETHTOOL_RESET 0x00000034 /* Reset hardware */
+#define ETHTOOL_SRXNTUPLE 0x00000035 /* Add an n-tuple filter to device */
+#define ETHTOOL_GRXNTUPLE 0x00000036 /* Get n-tuple filters from device */
+#define ETHTOOL_GSSET_INFO 0x00000037 /* Get string set info */
+#define ETHTOOL_GRXFHINDIR 0x00000038 /* Get RX flow hash indir'n table */
+#define ETHTOOL_SRXFHINDIR 0x00000039 /* Set RX flow hash indir'n table */
+
+#define ETHTOOL_GFEATURES 0x0000003a /* Get device offload settings */
+#define ETHTOOL_SFEATURES 0x0000003b /* Change device offload settings */
+
+/* compatibility with older code */
+#define SPARC_ETH_GSET ETHTOOL_GSET
+#define SPARC_ETH_SSET ETHTOOL_SSET
+
+/* Indicates what features are supported by the interface. */
+#define SUPPORTED_10baseT_Half (1 << 0)
+#define SUPPORTED_10baseT_Full (1 << 1)
+#define SUPPORTED_100baseT_Half (1 << 2)
+#define SUPPORTED_100baseT_Full (1 << 3)
+#define SUPPORTED_1000baseT_Half (1 << 4)
+#define SUPPORTED_1000baseT_Full (1 << 5)
+#define SUPPORTED_Autoneg (1 << 6)
+#define SUPPORTED_TP (1 << 7)
+#define SUPPORTED_AUI (1 << 8)
+#define SUPPORTED_MII (1 << 9)
+#define SUPPORTED_FIBRE (1 << 10)
+#define SUPPORTED_BNC (1 << 11)
+#define SUPPORTED_10000baseT_Full (1 << 12)
+#define SUPPORTED_Pause (1 << 13)
+#define SUPPORTED_Asym_Pause (1 << 14)
+#define SUPPORTED_2500baseX_Full (1 << 15)
+#define SUPPORTED_Backplane (1 << 16)
+#define SUPPORTED_1000baseKX_Full (1 << 17)
+#define SUPPORTED_10000baseKX4_Full (1 << 18)
+#define SUPPORTED_10000baseKR_Full (1 << 19)
+#define SUPPORTED_10000baseR_FEC (1 << 20)
+
+/* Indicates what features are advertised by the interface. */
+#define ADVERTISED_10baseT_Half (1 << 0)
+#define ADVERTISED_10baseT_Full (1 << 1)
+#define ADVERTISED_100baseT_Half (1 << 2)
+#define ADVERTISED_100baseT_Full (1 << 3)
+#define ADVERTISED_1000baseT_Half (1 << 4)
+#define ADVERTISED_1000baseT_Full (1 << 5)
+#define ADVERTISED_Autoneg (1 << 6)
+#define ADVERTISED_TP (1 << 7)
+#define ADVERTISED_AUI (1 << 8)
+#define ADVERTISED_MII (1 << 9)
+#define ADVERTISED_FIBRE (1 << 10)
+#define ADVERTISED_BNC (1 << 11)
+#define ADVERTISED_10000baseT_Full (1 << 12)
+#define ADVERTISED_Pause (1 << 13)
+#define ADVERTISED_Asym_Pause (1 << 14)
+#define ADVERTISED_2500baseX_Full (1 << 15)
+#define ADVERTISED_Backplane (1 << 16)
+#define ADVERTISED_1000baseKX_Full (1 << 17)
+#define ADVERTISED_10000baseKX4_Full (1 << 18)
+#define ADVERTISED_10000baseKR_Full (1 << 19)
+#define ADVERTISED_10000baseR_FEC (1 << 20)
+
+/* The following are all involved in forcing a particular link
+ * mode for the device for setting things. When getting the
+ * devices settings, these indicate the current mode and whether
+ * it was foced up into this mode or autonegotiated.
+ */
+
+/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
+#define SPEED_10 10
+#define SPEED_100 100
+#define SPEED_1000 1000
+#define SPEED_2500 2500
+#define SPEED_10000 10000
+
+/* Duplex, half or full. */
+#define DUPLEX_HALF 0x00
+#define DUPLEX_FULL 0x01
+
+/* Which connector port. */
+#define PORT_TP 0x00
+#define PORT_AUI 0x01
+#define PORT_MII 0x02
+#define PORT_FIBRE 0x03
+#define PORT_BNC 0x04
+#define PORT_DA 0x05
+#define PORT_NONE 0xef
+#define PORT_OTHER 0xff
+
+/* Which transceiver to use. */
+#define XCVR_INTERNAL 0x00
+#define XCVR_EXTERNAL 0x01
+#define XCVR_DUMMY1 0x02
+#define XCVR_DUMMY2 0x03
+#define XCVR_DUMMY3 0x04
+
+/* Enable or disable autonegotiation. If this is set to enable,
+ * the forced link modes above are completely ignored.
+ */
+#define AUTONEG_DISABLE 0x00
+#define AUTONEG_ENABLE 0x01
+
+/* Mode MDI or MDI-X */
+#define ETH_TP_MDI_INVALID 0x00
+#define ETH_TP_MDI 0x01
+#define ETH_TP_MDI_X 0x02
+
+/* Wake-On-Lan options. */
+#define WAKE_PHY (1 << 0)
+#define WAKE_UCAST (1 << 1)
+#define WAKE_MCAST (1 << 2)
+#define WAKE_BCAST (1 << 3)
+#define WAKE_ARP (1 << 4)
+#define WAKE_MAGIC (1 << 5)
+#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */
+
+/* L2-L4 network traffic flow types */
+#define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */
+#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */
+#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */
+#define AH_ESP_V4_FLOW 0x04 /* hash only */
+#define TCP_V6_FLOW 0x05 /* hash only */
+#define UDP_V6_FLOW 0x06 /* hash only */
+#define SCTP_V6_FLOW 0x07 /* hash only */
+#define AH_ESP_V6_FLOW 0x08 /* hash only */
+#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */
+#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */
+#define AH_V6_FLOW 0x0b /* hash only */
+#define ESP_V6_FLOW 0x0c /* hash only */
+#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define IPV4_FLOW 0x10 /* hash only */
+#define IPV6_FLOW 0x11 /* hash only */
+#define ETHER_FLOW 0x12 /* spec only (ether_spec) */
+
+/* L3-L4 network traffic flow hash options */
+#define RXH_L2DA (1 << 1)
+#define RXH_VLAN (1 << 2)
+#define RXH_L3_PROTO (1 << 3)
+#define RXH_IP_SRC (1 << 4)
+#define RXH_IP_DST (1 << 5)
+#define RXH_L4_B_0_1 (1 << 6) /* src port in case of TCP/UDP/SCTP */
+#define RXH_L4_B_2_3 (1 << 7) /* dst port in case of TCP/UDP/SCTP */
+#define RXH_DISCARD (1 << 31)
+
+#define RX_CLS_FLOW_DISC 0xffffffffffffffffULL
+
+/* Reset flags */
+/* The reset() operation must clear the flags for the components which
+ * were actually reset. On successful return, the flags indicate the
+ * components which were not reset, either because they do not exist
+ * in the hardware or because they cannot be reset independently. The
+ * driver must never reset any components that were not requested.
+ */
+enum ethtool_reset_flags {
+ /* These flags represent components dedicated to the interface
+ * the command is addressed to. Shift any flag left by
+ * ETH_RESET_SHARED_SHIFT to reset a shared component of the
+ * same type.
+ */
+ ETH_RESET_MGMT = 1 << 0, /* Management processor */
+ ETH_RESET_IRQ = 1 << 1, /* Interrupt requester */
+ ETH_RESET_DMA = 1 << 2, /* DMA engine */
+ ETH_RESET_FILTER = 1 << 3, /* Filtering/flow direction */
+ ETH_RESET_OFFLOAD = 1 << 4, /* Protocol offload */
+ ETH_RESET_MAC = 1 << 5, /* Media access controller */
+ ETH_RESET_PHY = 1 << 6, /* Transceiver/PHY */
+ ETH_RESET_RAM = 1 << 7, /* RAM shared between
+ * multiple components */
+
+ ETH_RESET_DEDICATED = 0x0000ffff, /* All components dedicated to
+ * this interface */
+ ETH_RESET_ALL = 0xffffffff, /* All components used by this
+ * interface, even if shared */
+};
+#define ETH_RESET_SHARED_SHIFT 16
+
+#endif /* _LINUX_ETHTOOL_H */
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
new file mode 100644
index 0000000..022d772
--- /dev/null
+++ b/include/linux/mdio.h
@@ -0,0 +1,278 @@
+/*
+ * linux/mdio.h: definitions for MDIO (clause 45) transceivers
+ * Copyright 2006-2009 Solarflare Communications Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation, incorporated herein by reference.
+ */
+
+#ifndef __LINUX_MDIO_H__
+#define __LINUX_MDIO_H__
+
+#include <linux/mii.h>
+
+/* MDIO Manageable Devices (MMDs). */
+#define MDIO_MMD_PMAPMD 1 /* Physical Medium Attachment/
+ * Physical Medium Dependent */
+#define MDIO_MMD_WIS 2 /* WAN Interface Sublayer */
+#define MDIO_MMD_PCS 3 /* Physical Coding Sublayer */
+#define MDIO_MMD_PHYXS 4 /* PHY Extender Sublayer */
+#define MDIO_MMD_DTEXS 5 /* DTE Extender Sublayer */
+#define MDIO_MMD_TC 6 /* Transmission Convergence */
+#define MDIO_MMD_AN 7 /* Auto-Negotiation */
+#define MDIO_MMD_C22EXT 29 /* Clause 22 extension */
+#define MDIO_MMD_VEND1 30 /* Vendor specific 1 */
+#define MDIO_MMD_VEND2 31 /* Vendor specific 2 */
+
+/* Generic MDIO registers. */
+#define MDIO_CTRL1 MII_BMCR
+#define MDIO_STAT1 MII_BMSR
+#define MDIO_DEVID1 MII_PHYSID1
+#define MDIO_DEVID2 MII_PHYSID2
+#define MDIO_SPEED 4 /* Speed ability */
+#define MDIO_DEVS1 5 /* Devices in package */
+#define MDIO_DEVS2 6
+#define MDIO_CTRL2 7 /* 10G control 2 */
+#define MDIO_STAT2 8 /* 10G status 2 */
+#define MDIO_PMA_TXDIS 9 /* 10G PMA/PMD transmit disable */
+#define MDIO_PMA_RXDET 10 /* 10G PMA/PMD receive signal detect */
+#define MDIO_PMA_EXTABLE 11 /* 10G PMA/PMD extended ability */
+#define MDIO_PKGID1 14 /* Package identifier */
+#define MDIO_PKGID2 15
+#define MDIO_AN_ADVERTISE 16 /* AN advertising (base page) */
+#define MDIO_AN_LPA 19 /* AN LP abilities (base page) */
+#define MDIO_PHYXS_LNSTAT 24 /* PHY XGXS lane state */
+
+/* Media-dependent registers. */
+#define MDIO_PMA_10GBT_SWAPPOL 130 /* 10GBASE-T pair swap & polarity */
+#define MDIO_PMA_10GBT_TXPWR 131 /* 10GBASE-T TX power control */
+#define MDIO_PMA_10GBT_SNR 133 /* 10GBASE-T SNR margin, lane A.
+ * Lanes B-D are numbered 134-136. */
+#define MDIO_PMA_10GBR_FECABLE 170 /* 10GBASE-R FEC ability */
+#define MDIO_PCS_10GBX_STAT1 24 /* 10GBASE-X PCS status 1 */
+#define MDIO_PCS_10GBRT_STAT1 32 /* 10GBASE-R/-T PCS status 1 */
+#define MDIO_PCS_10GBRT_STAT2 33 /* 10GBASE-R/-T PCS status 2 */
+#define MDIO_AN_10GBT_CTRL 32 /* 10GBASE-T auto-negotiation control */
+#define MDIO_AN_10GBT_STAT 33 /* 10GBASE-T auto-negotiation status */
+#define MDIO_AN_EEE_ADV 60 /* EEE advertisement */
+
+/* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */
+#define MDIO_PMA_LASI_RXCTRL 0x9000 /* RX_ALARM control */
+#define MDIO_PMA_LASI_TXCTRL 0x9001 /* TX_ALARM control */
+#define MDIO_PMA_LASI_CTRL 0x9002 /* LASI control */
+#define MDIO_PMA_LASI_RXSTAT 0x9003 /* RX_ALARM status */
+#define MDIO_PMA_LASI_TXSTAT 0x9004 /* TX_ALARM status */
+#define MDIO_PMA_LASI_STAT 0x9005 /* LASI status */
+
+/* Control register 1. */
+/* Enable extended speed selection */
+#define MDIO_CTRL1_SPEEDSELEXT (BMCR_SPEED1000 | BMCR_SPEED100)
+/* All speed selection bits */
+#define MDIO_CTRL1_SPEEDSEL (MDIO_CTRL1_SPEEDSELEXT | 0x003c)
+#define MDIO_CTRL1_FULLDPLX BMCR_FULLDPLX
+#define MDIO_CTRL1_LPOWER BMCR_PDOWN
+#define MDIO_CTRL1_RESET BMCR_RESET
+#define MDIO_PMA_CTRL1_LOOPBACK 0x0001
+#define MDIO_PMA_CTRL1_SPEED1000 BMCR_SPEED1000
+#define MDIO_PMA_CTRL1_SPEED100 BMCR_SPEED100
+#define MDIO_PCS_CTRL1_LOOPBACK BMCR_LOOPBACK
+#define MDIO_PHYXS_CTRL1_LOOPBACK BMCR_LOOPBACK
+#define MDIO_AN_CTRL1_RESTART BMCR_ANRESTART
+#define MDIO_AN_CTRL1_ENABLE BMCR_ANENABLE
+#define MDIO_AN_CTRL1_XNP 0x2000 /* Enable extended next page */
+
+/* 10 Gb/s */
+#define MDIO_CTRL1_SPEED10G (MDIO_CTRL1_SPEEDSELEXT | 0x00)
+/* 10PASS-TS/2BASE-TL */
+#define MDIO_CTRL1_SPEED10P2B (MDIO_CTRL1_SPEEDSELEXT | 0x04)
+
+/* Status register 1. */
+#define MDIO_STAT1_LPOWERABLE 0x0002 /* Low-power ability */
+#define MDIO_STAT1_LSTATUS BMSR_LSTATUS
+#define MDIO_STAT1_FAULT 0x0080 /* Fault */
+#define MDIO_AN_STAT1_LPABLE 0x0001 /* Link partner AN ability */
+#define MDIO_AN_STAT1_ABLE BMSR_ANEGCAPABLE
+#define MDIO_AN_STAT1_RFAULT BMSR_RFAULT
+#define MDIO_AN_STAT1_COMPLETE BMSR_ANEGCOMPLETE
+#define MDIO_AN_STAT1_PAGE 0x0040 /* Page received */
+#define MDIO_AN_STAT1_XNP 0x0080 /* Extended next page status */
+
+/* Speed register. */
+#define MDIO_SPEED_10G 0x0001 /* 10G capable */
+#define MDIO_PMA_SPEED_2B 0x0002 /* 2BASE-TL capable */
+#define MDIO_PMA_SPEED_10P 0x0004 /* 10PASS-TS capable */
+#define MDIO_PMA_SPEED_1000 0x0010 /* 1000M capable */
+#define MDIO_PMA_SPEED_100 0x0020 /* 100M capable */
+#define MDIO_PMA_SPEED_10 0x0040 /* 10M capable */
+#define MDIO_PCS_SPEED_10P2B 0x0002 /* 10PASS-TS/2BASE-TL capable */
+
+/* Device present registers. */
+#define MDIO_DEVS_PRESENT(devad) (1 << (devad))
+#define MDIO_DEVS_PMAPMD MDIO_DEVS_PRESENT(MDIO_MMD_PMAPMD)
+#define MDIO_DEVS_WIS MDIO_DEVS_PRESENT(MDIO_MMD_WIS)
+#define MDIO_DEVS_PCS MDIO_DEVS_PRESENT(MDIO_MMD_PCS)
+#define MDIO_DEVS_PHYXS MDIO_DEVS_PRESENT(MDIO_MMD_PHYXS)
+#define MDIO_DEVS_DTEXS MDIO_DEVS_PRESENT(MDIO_MMD_DTEXS)
+#define MDIO_DEVS_TC MDIO_DEVS_PRESENT(MDIO_MMD_TC)
+#define MDIO_DEVS_AN MDIO_DEVS_PRESENT(MDIO_MMD_AN)
+#define MDIO_DEVS_C22EXT MDIO_DEVS_PRESENT(MDIO_MMD_C22EXT)
+#define MDIO_DEVS_VEND1 MDIO_DEVS_PRESENT(MDIO_MMD_VEND1)
+#define MDIO_DEVS_VEND2 MDIO_DEVS_PRESENT(MDIO_MMD_VEND2)
+
+
+/* Control register 2. */
+#define MDIO_PMA_CTRL2_TYPE 0x000f /* PMA/PMD type selection */
+#define MDIO_PMA_CTRL2_10GBCX4 0x0000 /* 10GBASE-CX4 type */
+#define MDIO_PMA_CTRL2_10GBEW 0x0001 /* 10GBASE-EW type */
+#define MDIO_PMA_CTRL2_10GBLW 0x0002 /* 10GBASE-LW type */
+#define MDIO_PMA_CTRL2_10GBSW 0x0003 /* 10GBASE-SW type */
+#define MDIO_PMA_CTRL2_10GBLX4 0x0004 /* 10GBASE-LX4 type */
+#define MDIO_PMA_CTRL2_10GBER 0x0005 /* 10GBASE-ER type */
+#define MDIO_PMA_CTRL2_10GBLR 0x0006 /* 10GBASE-LR type */
+#define MDIO_PMA_CTRL2_10GBSR 0x0007 /* 10GBASE-SR type */
+#define MDIO_PMA_CTRL2_10GBLRM 0x0008 /* 10GBASE-LRM type */
+#define MDIO_PMA_CTRL2_10GBT 0x0009 /* 10GBASE-T type */
+#define MDIO_PMA_CTRL2_10GBKX4 0x000a /* 10GBASE-KX4 type */
+#define MDIO_PMA_CTRL2_10GBKR 0x000b /* 10GBASE-KR type */
+#define MDIO_PMA_CTRL2_1000BT 0x000c /* 1000BASE-T type */
+#define MDIO_PMA_CTRL2_1000BKX 0x000d /* 1000BASE-KX type */
+#define MDIO_PMA_CTRL2_100BTX 0x000e /* 100BASE-TX type */
+#define MDIO_PMA_CTRL2_10BT 0x000f /* 10BASE-T type */
+#define MDIO_PCS_CTRL2_TYPE 0x0003 /* PCS type selection */
+#define MDIO_PCS_CTRL2_10GBR 0x0000 /* 10GBASE-R type */
+#define MDIO_PCS_CTRL2_10GBX 0x0001 /* 10GBASE-X type */
+#define MDIO_PCS_CTRL2_10GBW 0x0002 /* 10GBASE-W type */
+#define MDIO_PCS_CTRL2_10GBT 0x0003 /* 10GBASE-T type */
+
+/* Status register 2. */
+#define MDIO_STAT2_RXFAULT 0x0400 /* Receive fault */
+#define MDIO_STAT2_TXFAULT 0x0800 /* Transmit fault */
+#define MDIO_STAT2_DEVPRST 0xc000 /* Device present */
+#define MDIO_STAT2_DEVPRST_VAL 0x8000 /* Device present value */
+#define MDIO_PMA_STAT2_LBABLE 0x0001 /* PMA loopback ability */
+#define MDIO_PMA_STAT2_10GBEW 0x0002 /* 10GBASE-EW ability */
+#define MDIO_PMA_STAT2_10GBLW 0x0004 /* 10GBASE-LW ability */
+#define MDIO_PMA_STAT2_10GBSW 0x0008 /* 10GBASE-SW ability */
+#define MDIO_PMA_STAT2_10GBLX4 0x0010 /* 10GBASE-LX4 ability */
+#define MDIO_PMA_STAT2_10GBER 0x0020 /* 10GBASE-ER ability */
+#define MDIO_PMA_STAT2_10GBLR 0x0040 /* 10GBASE-LR ability */
+#define MDIO_PMA_STAT2_10GBSR 0x0080 /* 10GBASE-SR ability */
+#define MDIO_PMD_STAT2_TXDISAB 0x0100 /* PMD TX disable ability */
+#define MDIO_PMA_STAT2_EXTABLE 0x0200 /* Extended abilities */
+#define MDIO_PMA_STAT2_RXFLTABLE 0x1000 /* Receive fault ability */
+#define MDIO_PMA_STAT2_TXFLTABLE 0x2000 /* Transmit fault ability */
+#define MDIO_PCS_STAT2_10GBR 0x0001 /* 10GBASE-R capable */
+#define MDIO_PCS_STAT2_10GBX 0x0002 /* 10GBASE-X capable */
+#define MDIO_PCS_STAT2_10GBW 0x0004 /* 10GBASE-W capable */
+#define MDIO_PCS_STAT2_RXFLTABLE 0x1000 /* Receive fault ability */
+#define MDIO_PCS_STAT2_TXFLTABLE 0x2000 /* Transmit fault ability */
+
+/* Transmit disable register. */
+#define MDIO_PMD_TXDIS_GLOBAL 0x0001 /* Global PMD TX disable */
+#define MDIO_PMD_TXDIS_0 0x0002 /* PMD TX disable 0 */
+#define MDIO_PMD_TXDIS_1 0x0004 /* PMD TX disable 1 */
+#define MDIO_PMD_TXDIS_2 0x0008 /* PMD TX disable 2 */
+#define MDIO_PMD_TXDIS_3 0x0010 /* PMD TX disable 3 */
+
+/* Receive signal detect register. */
+#define MDIO_PMD_RXDET_GLOBAL 0x0001 /* Global PMD RX signal detect */
+#define MDIO_PMD_RXDET_0 0x0002 /* PMD RX signal detect 0 */
+#define MDIO_PMD_RXDET_1 0x0004 /* PMD RX signal detect 1 */
+#define MDIO_PMD_RXDET_2 0x0008 /* PMD RX signal detect 2 */
+#define MDIO_PMD_RXDET_3 0x0010 /* PMD RX signal detect 3 */
+
+/* Extended abilities register. */
+#define MDIO_PMA_EXTABLE_10GCX4 0x0001 /* 10GBASE-CX4 ability */
+#define MDIO_PMA_EXTABLE_10GBLRM 0x0002 /* 10GBASE-LRM ability */
+#define MDIO_PMA_EXTABLE_10GBT 0x0004 /* 10GBASE-T ability */
+#define MDIO_PMA_EXTABLE_10GBKX4 0x0008 /* 10GBASE-KX4 ability */
+#define MDIO_PMA_EXTABLE_10GBKR 0x0010 /* 10GBASE-KR ability */
+#define MDIO_PMA_EXTABLE_1000BT 0x0020 /* 1000BASE-T ability */
+#define MDIO_PMA_EXTABLE_1000BKX 0x0040 /* 1000BASE-KX ability */
+#define MDIO_PMA_EXTABLE_100BTX 0x0080 /* 100BASE-TX ability */
+#define MDIO_PMA_EXTABLE_10BT 0x0100 /* 10BASE-T ability */
+
+/* PHY XGXS lane state register. */
+#define MDIO_PHYXS_LNSTAT_SYNC0 0x0001
+#define MDIO_PHYXS_LNSTAT_SYNC1 0x0002
+#define MDIO_PHYXS_LNSTAT_SYNC2 0x0004
+#define MDIO_PHYXS_LNSTAT_SYNC3 0x0008
+#define MDIO_PHYXS_LNSTAT_ALIGN 0x1000
+
+/* PMA 10GBASE-T pair swap & polarity */
+#define MDIO_PMA_10GBT_SWAPPOL_ABNX 0x0001 /* Pair A/B uncrossed */
+#define MDIO_PMA_10GBT_SWAPPOL_CDNX 0x0002 /* Pair C/D uncrossed */
+#define MDIO_PMA_10GBT_SWAPPOL_AREV 0x0100 /* Pair A polarity reversed */
+#define MDIO_PMA_10GBT_SWAPPOL_BREV 0x0200 /* Pair B polarity reversed */
+#define MDIO_PMA_10GBT_SWAPPOL_CREV 0x0400 /* Pair C polarity reversed */
+#define MDIO_PMA_10GBT_SWAPPOL_DREV 0x0800 /* Pair D polarity reversed */
+
+/* PMA 10GBASE-T TX power register. */
+#define MDIO_PMA_10GBT_TXPWR_SHORT 0x0001 /* Short-reach mode */
+
+/* PMA 10GBASE-T SNR registers. */
+/* Value is SNR margin in dB, clamped to range [-127, 127], plus 0x8000. */
+#define MDIO_PMA_10GBT_SNR_BIAS 0x8000
+#define MDIO_PMA_10GBT_SNR_MAX 127
+
+/* PMA 10GBASE-R FEC ability register. */
+#define MDIO_PMA_10GBR_FECABLE_ABLE 0x0001 /* FEC ability */
+#define MDIO_PMA_10GBR_FECABLE_ERRABLE 0x0002 /* FEC error indic. ability */
+
+/* PCS 10GBASE-R/-T status register 1. */
+#define MDIO_PCS_10GBRT_STAT1_BLKLK 0x0001 /* Block lock attained */
+
+/* PCS 10GBASE-R/-T status register 2. */
+#define MDIO_PCS_10GBRT_STAT2_ERR 0x00ff
+#define MDIO_PCS_10GBRT_STAT2_BER 0x3f00
+
+/* AN 10GBASE-T control register. */
+#define MDIO_AN_10GBT_CTRL_ADV10G 0x1000 /* Advertise 10GBASE-T */
+
+/* AN 10GBASE-T status register. */
+#define MDIO_AN_10GBT_STAT_LPTRR 0x0200 /* LP training reset req. */
+#define MDIO_AN_10GBT_STAT_LPLTABLE 0x0400 /* LP loop timing ability */
+#define MDIO_AN_10GBT_STAT_LP10G 0x0800 /* LP is 10GBT capable */
+#define MDIO_AN_10GBT_STAT_REMOK 0x1000 /* Remote OK */
+#define MDIO_AN_10GBT_STAT_LOCOK 0x2000 /* Local OK */
+#define MDIO_AN_10GBT_STAT_MS 0x4000 /* Master/slave config */
+#define MDIO_AN_10GBT_STAT_MSFLT 0x8000 /* Master/slave config fault */
+
+/* AN EEE Advertisement register. */
+#define MDIO_AN_EEE_ADV_100TX 0x0002 /* Advertise 100TX EEE cap */
+#define MDIO_AN_EEE_ADV_1000T 0x0004 /* Advertise 1000T EEE cap */
+
+/* LASI RX_ALARM control/status registers. */
+#define MDIO_PMA_LASI_RX_PHYXSLFLT 0x0001 /* PHY XS RX local fault */
+#define MDIO_PMA_LASI_RX_PCSLFLT 0x0008 /* PCS RX local fault */
+#define MDIO_PMA_LASI_RX_PMALFLT 0x0010 /* PMA/PMD RX local fault */
+#define MDIO_PMA_LASI_RX_OPTICPOWERFLT 0x0020 /* RX optical power fault */
+#define MDIO_PMA_LASI_RX_WISLFLT 0x0200 /* WIS local fault */
+
+/* LASI TX_ALARM control/status registers. */
+#define MDIO_PMA_LASI_TX_PHYXSLFLT 0x0001 /* PHY XS TX local fault */
+#define MDIO_PMA_LASI_TX_PCSLFLT 0x0008 /* PCS TX local fault */
+#define MDIO_PMA_LASI_TX_PMALFLT 0x0010 /* PMA/PMD TX local fault */
+#define MDIO_PMA_LASI_TX_LASERPOWERFLT 0x0080 /* Laser output power fault */
+#define MDIO_PMA_LASI_TX_LASERTEMPFLT 0x0100 /* Laser temperature fault */
+#define MDIO_PMA_LASI_TX_LASERBICURRFLT 0x0200 /* Laser bias current fault */
+
+/* LASI control/status registers. */
+#define MDIO_PMA_LASI_LSALARM 0x0001 /* LS_ALARM enable/status */
+#define MDIO_PMA_LASI_TXALARM 0x0002 /* TX_ALARM enable/status */
+#define MDIO_PMA_LASI_RXALARM 0x0004 /* RX_ALARM enable/status */
+
+/* Mapping between MDIO PRTAD/DEVAD and mii_ioctl_data::phy_id */
+
+#define MDIO_PHY_ID_C45 0x8000
+#define MDIO_PHY_ID_PRTAD 0x03e0
+#define MDIO_PHY_ID_DEVAD 0x001f
+#define MDIO_PHY_ID_C45_MASK \
+ (MDIO_PHY_ID_C45 | MDIO_PHY_ID_PRTAD | MDIO_PHY_ID_DEVAD)
+
+#define MDIO_PRTAD_NONE (-1)
+#define MDIO_DEVAD_NONE (-1)
+#define MDIO_EMULATE_C22 4
+
+#endif /* __LINUX_MDIO_H__ */
diff --git a/include/miiphy.h b/include/miiphy.h
index 34ebce6..7e70cf8 100644
--- a/include/miiphy.h
+++ b/include/miiphy.h
@@ -34,8 +34,18 @@
#ifndef _miiphy_h_
#define _miiphy_h_
+#include <common.h>
#include <linux/mii.h>
+#include <linux/list.h>
#include <net.h>
+#include <phy.h>
+
+struct legacy_mii_dev {
+ int (*read)(const char *devname, unsigned char addr,
+ unsigned char reg, unsigned short *value);
+ int (*write)(const char *devname, unsigned char addr,
+ unsigned char reg, unsigned short value);
+};
int miiphy_read(const char *devname, unsigned char addr, unsigned char reg,
unsigned short *value);
@@ -61,9 +71,16 @@ void miiphy_register(const char *devname,
int miiphy_set_current_dev(const char *devname);
const char *miiphy_get_current_dev(void);
+struct mii_dev *mdio_get_current_dev(void);
+struct mii_dev *miiphy_get_dev_by_name(const char *devname);
+struct phy_device *mdio_phydev_for_ethname(const char *devname);
void miiphy_listdev(void);
+struct mii_dev *mdio_alloc(void);
+int mdio_register(struct mii_dev *bus);
+void mdio_list_devices(void);
+
#ifdef CONFIG_BITBANGMII
#define BB_MII_DEVNAME "bb_miiphy"
diff --git a/include/phy.h b/include/phy.h
new file mode 100644
index 0000000..2abd23b
--- /dev/null
+++ b/include/phy.h
@@ -0,0 +1,219 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Andy Fleming <afleming@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * This file pretty much stolen from Linux's mii.h/ethtool.h/phy.h
+ */
+
+#ifndef _PHY_H
+#define _PHY_H
+
+#include <linux/list.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/mdio.h>
+
+#define PHY_MAX_ADDR 32
+
+#define PHY_BASIC_FEATURES (SUPPORTED_10baseT_Half | \
+ SUPPORTED_10baseT_Full | \
+ SUPPORTED_100baseT_Half | \
+ SUPPORTED_100baseT_Full | \
+ SUPPORTED_Autoneg | \
+ SUPPORTED_TP | \
+ SUPPORTED_MII)
+
+#define PHY_GBIT_FEATURES (PHY_BASIC_FEATURES | \
+ SUPPORTED_1000baseT_Half | \
+ SUPPORTED_1000baseT_Full)
+
+#define PHY_10G_FEATURES (PHY_GBIT_FEATURES | \
+ SUPPORTED_10000baseT_Full)
+
+#define PHY_ANEG_TIMEOUT 4000
+
+
+typedef enum {
+ PHY_INTERFACE_MODE_MII,
+ PHY_INTERFACE_MODE_GMII,
+ PHY_INTERFACE_MODE_SGMII,
+ PHY_INTERFACE_MODE_TBI,
+ PHY_INTERFACE_MODE_RMII,
+ PHY_INTERFACE_MODE_RGMII,
+ PHY_INTERFACE_MODE_RGMII_ID,
+ PHY_INTERFACE_MODE_RGMII_RXID,
+ PHY_INTERFACE_MODE_RGMII_TXID,
+ PHY_INTERFACE_MODE_RTBI,
+ PHY_INTERFACE_MODE_XGMII,
+ PHY_INTERFACE_MODE_NONE /* Must be last */
+} phy_interface_t;
+
+static const char *phy_interface_strings[] = {
+ [PHY_INTERFACE_MODE_MII] = "mii",
+ [PHY_INTERFACE_MODE_GMII] = "gmii",
+ [PHY_INTERFACE_MODE_SGMII] = "sgmii",
+ [PHY_INTERFACE_MODE_TBI] = "tbi",
+ [PHY_INTERFACE_MODE_RMII] = "rmii",
+ [PHY_INTERFACE_MODE_RGMII] = "rgmii",
+ [PHY_INTERFACE_MODE_RGMII_ID] = "rgmii-id",
+ [PHY_INTERFACE_MODE_RGMII_RXID] = "rgmii-rxid",
+ [PHY_INTERFACE_MODE_RGMII_TXID] = "rgmii-txid",
+ [PHY_INTERFACE_MODE_RTBI] = "rtbi",
+ [PHY_INTERFACE_MODE_XGMII] = "xgmii",
+ [PHY_INTERFACE_MODE_NONE] = "",
+};
+
+static inline const char *phy_string_for_interface(phy_interface_t i)
+{
+ /* Default to unknown */
+ if (i > PHY_INTERFACE_MODE_NONE)
+ i = PHY_INTERFACE_MODE_NONE;
+
+ return phy_interface_strings[i];
+}
+
+
+struct phy_device;
+
+#define MDIO_NAME_LEN 32
+
+struct mii_dev {
+ struct list_head link;
+ char name[MDIO_NAME_LEN];
+ void *priv;
+ int (*read)(struct mii_dev *bus, int addr, int devad, int reg);
+ int (*write)(struct mii_dev *bus, int addr, int devad, int reg,
+ u16 val);
+ int (*reset)(struct mii_dev *bus);
+ struct phy_device *phymap[PHY_MAX_ADDR];
+ u32 phy_mask;
+};
+
+/* struct phy_driver: a structure which defines PHY behavior
+ *
+ * uid will contain a number which represents the PHY. During
+ * startup, the driver will poll the PHY to find out what its
+ * UID--as defined by registers 2 and 3--is. The 32-bit result
+ * gotten from the PHY will be masked to
+ * discard any bits which may change based on revision numbers
+ * unimportant to functionality
+ *
+ */
+struct phy_driver {
+ char *name;
+ unsigned int uid;
+ unsigned int mask;
+ unsigned int mmds;
+
+ u32 features;
+
+ /* Called to do any driver startup necessities */
+ /* Will be called during phy_connect */
+ int (*probe)(struct phy_device *phydev);
+
+ /* Called to configure the PHY, and modify the controller
+ * based on the results. Should be called after phy_connect */
+ int (*config)(struct phy_device *phydev);
+
+ /* Called when starting up the controller */
+ int (*startup)(struct phy_device *phydev);
+
+ /* Called when bringing down the controller */
+ int (*shutdown)(struct phy_device *phydev);
+
+ struct list_head list;
+};
+
+struct phy_device {
+ /* Information about the PHY type */
+ /* And management functions */
+ struct mii_dev *bus;
+ struct phy_driver *drv;
+ void *priv;
+
+ struct eth_device *dev;
+
+ /* forced speed & duplex (no autoneg)
+ * partner speed & duplex & pause (autoneg)
+ */
+ int speed;
+ int duplex;
+
+ /* The most recently read link state */
+ int link;
+ int port;
+ phy_interface_t interface;
+
+ u32 advertising;
+ u32 supported;
+ u32 mmds;
+
+ int autoneg;
+ int addr;
+ int pause;
+ int asym_pause;
+ u32 phy_id;
+ u32 flags;
+};
+
+static inline int phy_read(struct phy_device *phydev, int devad, int regnum)
+{
+ struct mii_dev *bus = phydev->bus;
+
+ return bus->read(bus, phydev->addr, devad, regnum);
+}
+
+static inline int phy_write(struct phy_device *phydev, int devad, int regnum,
+ u16 val)
+{
+ struct mii_dev *bus = phydev->bus;
+
+ return bus->write(bus, phydev->addr, devad, regnum, val);
+}
+
+#ifdef CONFIG_PHYLIB_10G
+extern struct phy_driver gen10g_driver;
+
+/* For now, XGMII is the only 10G interface */
+static inline int is_10g_interface(phy_interface_t interface)
+{
+ return interface == PHY_INTERFACE_MODE_XGMII;
+}
+
+#endif
+
+int phy_init(void);
+int phy_reset(struct phy_device *phydev);
+struct phy_device *phy_connect(struct mii_dev *bus, int addr,
+ struct eth_device *dev,
+ phy_interface_t interface);
+int phy_startup(struct phy_device *phydev);
+int phy_config(struct phy_device *phydev);
+int phy_shutdown(struct phy_device *phydev);
+int phy_register(struct phy_driver *drv);
+int genphy_config_aneg(struct phy_device *phydev);
+int genphy_update_link(struct phy_device *phydev);
+int genphy_config(struct phy_device *phydev);
+int genphy_startup(struct phy_device *phydev);
+int genphy_shutdown(struct phy_device *phydev);
+int gen10g_config(struct phy_device *phydev);
+int gen10g_startup(struct phy_device *phydev);
+int gen10g_shutdown(struct phy_device *phydev);
+int gen10g_discover_mmds(struct phy_device *phydev);
+
+#endif
diff --git a/net/eth.c b/net/eth.c
index 3a7ff50..6523834 100644
--- a/net/eth.c
+++ b/net/eth.c
@@ -25,6 +25,7 @@
#include <command.h>
#include <net.h>
#include <miiphy.h>
+#include <phy.h>
void eth_parse_enetaddr(const char *addr, uchar *enetaddr)
{
@@ -217,6 +218,11 @@ int eth_initialize(bd_t *bis)
#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
miiphy_init();
#endif
+
+#ifdef CONFIG_PHYLIB
+ phy_init();
+#endif
+
/*
* If board-specific initialization exists, call it.
* If not, call a CPU-specific one