summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--board/freescale/mx6q_sabresd/mx6q_sabresd.c3
-rw-r--r--board/freescale/mx6sl_arm2/mx6sl_arm2.c313
-rw-r--r--include/configs/mx6sl_arm2.h13
3 files changed, 329 insertions, 0 deletions
diff --git a/board/freescale/mx6q_sabresd/mx6q_sabresd.c b/board/freescale/mx6q_sabresd/mx6q_sabresd.c
index ceb6c46..daeff26 100644
--- a/board/freescale/mx6q_sabresd/mx6q_sabresd.c
+++ b/board/freescale/mx6q_sabresd/mx6q_sabresd.c
@@ -686,6 +686,9 @@ int i2c_bus_recovery(void)
void setup_pmic_voltages(void)
{
unsigned char value = 0 ;
+ #if CONFIG_MX6_INTER_LDO_BYPASS
+ unsigned int val = 0;
+ #endif
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
if (!i2c_probe(0x8)) {
if (i2c_read(0x8, 0, 1, &value, 1))
diff --git a/board/freescale/mx6sl_arm2/mx6sl_arm2.c b/board/freescale/mx6sl_arm2/mx6sl_arm2.c
index 60a263f..13428cb 100644
--- a/board/freescale/mx6sl_arm2/mx6sl_arm2.c
+++ b/board/freescale/mx6sl_arm2/mx6sl_arm2.c
@@ -26,6 +26,7 @@
#include <asm/arch/mx6_pins.h>
#include <asm/arch/mx6sl_pins.h>
#include <asm/arch/iomux-v3.h>
+#include <asm/arch/regs-anadig.h>
#include <asm/errno.h>
#ifdef CONFIG_MXC_FEC
#include <miiphy.h>
@@ -53,6 +54,10 @@
#include <recovery.h>
#endif
+#if CONFIG_I2C_MXC
+#include <i2c.h>
+#endif
+
DECLARE_GLOBAL_DATA_PTR;
static u32 system_rev;
@@ -685,6 +690,309 @@ static int setup_fec(void)
}
#endif
+#ifdef CONFIG_I2C_MXC
+#define I2C1_SCL_GPIO3_12_BIT_MASK (1 << 12)
+#define I2C1_SDA_GPIO3_13_BIT_MASK (1 << 13)
+#define I2C2_SCL_GPIO3_14_BIT_MASK (1 << 14)
+#define I2C2_SDA_GPIO3_15_BIT_MASK (1 << 15)
+
+
+static void setup_i2c(unsigned int module_base)
+{
+ unsigned int reg;
+
+ switch (module_base) {
+ case I2C1_BASE_ADDR:
+ /* i2c1 SDA */
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C1_SDA__I2C1_SDA);
+ /* i2c1 SCL */
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C1_SCL__I2C1_SCL);
+
+ /* Enable i2c clock */
+ reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR2);
+ reg |= 0xC0;
+ writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR2);
+
+ break;
+ case I2C2_BASE_ADDR:
+ /* i2c2 SDA */
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C2_SDA__I2C2_SDA);
+
+ /* i2c2 SCL */
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C2_SCL__I2C2_SCL);
+
+ /* Enable i2c clock */
+ reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR2);
+ reg |= 0x300;
+ writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR2);
+
+ break;
+ default:
+ printf("Invalid I2C base: 0x%x\n", module_base);
+ break;
+ }
+}
+
+/* Note: udelay() is not accurate for i2c timing */
+static void __udelay(int time)
+{
+ int i, j;
+
+ for (i = 0; i < time; i++) {
+ for (j = 0; j < 200; j++) {
+ asm("nop");
+ asm("nop");
+ }
+ }
+}
+
+static void mx6sl_i2c_gpio_scl_direction(int bus, int output)
+{
+ u32 reg;
+
+ switch (bus) {
+ case 1:
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C1_SCL__GPIO_3_12);
+ reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+ if (output)
+ reg |= I2C1_SCL_GPIO3_12_BIT_MASK;
+ else
+ reg &= ~I2C1_SCL_GPIO3_12_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+ break;
+ case 2:
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C2_SCL__GPIO_3_14);
+ reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+ if (output)
+ reg |= I2C2_SCL_GPIO3_14_BIT_MASK;
+ else
+ reg &= ~I2C2_SCL_GPIO3_14_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+ break;
+ }
+}
+
+/* set 1 to output, sent 0 to input */
+static void mx6sl_i2c_gpio_sda_direction(int bus, int output)
+{
+ u32 reg;
+
+ switch (bus) {
+ case 1:
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C1_SDA__GPIO_3_13);
+ reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+ if (output)
+ reg |= I2C1_SDA_GPIO3_13_BIT_MASK;
+ else
+ reg &= ~I2C1_SDA_GPIO3_13_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+ break;
+ case 2:
+ mxc_iomux_v3_setup_pad(MX6SL_PAD_I2C2_SDA__GPIO_3_15);
+ reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+ if (output)
+ reg |= I2C2_SDA_GPIO3_15_BIT_MASK;
+ else
+ reg &= ~I2C2_SDA_GPIO3_15_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+ break;
+ }
+}
+
+
+/* set 1 to high 0 to low */
+static void mx6sl_i2c_gpio_scl_set_level(int bus, int high)
+{
+ u32 reg;
+
+ switch (bus) {
+ case 1:
+ reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+ if (high)
+ reg |= I2C1_SCL_GPIO3_12_BIT_MASK;
+ else
+ reg &= ~I2C1_SCL_GPIO3_12_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+ break;
+ case 2:
+ reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+ if (high)
+ reg |= I2C2_SCL_GPIO3_14_BIT_MASK;
+ else
+ reg &= ~I2C2_SCL_GPIO3_14_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+ break;
+ }
+}
+
+/* set 1 to high 0 to low */
+static void mx6sl_i2c_gpio_sda_set_level(int bus, int high)
+{
+ u32 reg;
+
+ switch (bus) {
+ case 1:
+ reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+ if (high)
+ reg |= I2C1_SDA_GPIO3_13_BIT_MASK;
+ else
+ reg &= ~I2C1_SDA_GPIO3_13_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+ break;
+ case 2:
+ reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+ if (high)
+ reg |= I2C2_SDA_GPIO3_15_BIT_MASK;
+ else
+ reg &= ~I2C2_SDA_GPIO3_15_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+ break;
+ }
+}
+
+
+static int mx6sl_i2c_gpio_check_sda(int bus)
+{
+ u32 reg;
+ int result = 0;
+
+ switch (bus) {
+ case 1:
+ reg = readl(GPIO3_BASE_ADDR + GPIO_PSR);
+ result = !!(reg & I2C1_SDA_GPIO3_13_BIT_MASK);
+ break;
+ case 2:
+ reg = readl(GPIO3_BASE_ADDR + GPIO_PSR);
+ result = !!(reg & I2C2_SDA_GPIO3_15_BIT_MASK);
+ break;
+ }
+
+ return result;
+}
+
+ /* Random reboot cause i2c SDA low issue:
+ * the i2c bus busy because some device pull down the I2C SDA
+ * line. This happens when Host is reading some byte from slave, and
+ * then host is reset/reboot. Since in this case, device is
+ * controlling i2c SDA line, the only thing host can do this give the
+ * clock on SCL and sending NAK, and STOP to finish this
+ * transaction.
+ *
+ * How to fix this issue:
+ * detect if the SDA was low on bus send 8 dummy clock, and 1
+ * clock + NAK, and STOP to finish i2c transaction the pending
+ * transfer.
+ */
+int i2c_bus_recovery(void)
+{
+ int i, bus, result = 0;
+
+ for (bus = 1; bus <= 2; bus++) {
+ mx6sl_i2c_gpio_sda_direction(bus, 0);
+
+ if (mx6sl_i2c_gpio_check_sda(bus) == 0) {
+ printf("i2c: I2C%d SDA is low, start i2c recovery...\n", bus);
+ mx6sl_i2c_gpio_scl_direction(bus, 1);
+ mx6sl_i2c_gpio_scl_set_level(bus, 1);
+ __udelay(10000);
+
+ for (i = 0; i < 9; i++) {
+ mx6sl_i2c_gpio_scl_set_level(bus, 1);
+ __udelay(5);
+ mx6sl_i2c_gpio_scl_set_level(bus, 0);
+ __udelay(5);
+ }
+
+ /* 9th clock here, the slave should already
+ release the SDA, we can set SDA as high to
+ a NAK.*/
+ mx6sl_i2c_gpio_sda_direction(bus, 1);
+ mx6sl_i2c_gpio_sda_set_level(bus, 1);
+ __udelay(1); /* Pull up SDA first */
+ mx6sl_i2c_gpio_scl_set_level(bus, 1);
+ __udelay(5); /* plus pervious 1 us */
+ mx6sl_i2c_gpio_scl_set_level(bus, 0);
+ __udelay(5);
+ mx6sl_i2c_gpio_sda_set_level(bus, 0);
+ __udelay(5);
+ mx6sl_i2c_gpio_scl_set_level(bus, 1);
+ __udelay(5);
+ /* Here: SCL is high, and SDA from low to high, it's a
+ * stop condition */
+ mx6sl_i2c_gpio_sda_set_level(bus, 1);
+ __udelay(5);
+
+ mx6sl_i2c_gpio_sda_direction(bus, 0);
+ if (mx6sl_i2c_gpio_check_sda(bus) == 1)
+ printf("I2C%d Recovery success\n", bus);
+ else {
+ printf("I2C%d Recovery failed, I2C1 SDA still low!!!\n", bus);
+ result |= 1 << bus;
+ }
+ }
+ /* configure back to i2c */
+ switch (bus) {
+ case 1:
+ setup_i2c(I2C1_BASE_ADDR);
+ break;
+ case 2:
+ setup_i2c(I2C2_BASE_ADDR);
+ break;
+ }
+ }
+
+ return result;
+}
+
+
+void setup_pmic_voltages(void)
+{
+ unsigned char value = 0 ;
+ #if CONFIG_MX6_INTER_LDO_BYPASS
+ unsigned int val = 0;
+ #endif
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+ if (!i2c_probe(0x8)) {
+ if (i2c_read(0x8, 0, 1, &value, 1))
+ printf("%s:i2c_read:error\n", __func__);
+ printf("Found PFUZE100! device id=%x\n", value);
+ #if CONFIG_MX6_INTER_LDO_BYPASS
+ /*VDDCORE 1.1V@800Mhz: SW1AB*/
+ value = 0x20;
+ i2c_write(0x8, 0x20, 1, &value, 1);
+
+ /*VDDSOC 1.2V : SW1C*/
+ value = 0x24;
+ i2c_write(0x8, 0x2e, 1, &value, 1);
+
+ /* Bypass the VDDSOC from Anatop */
+ val = REG_RD(ANATOP_BASE_ADDR, HW_ANADIG_REG_CORE);
+ val &= ~BM_ANADIG_REG_CORE_REG2_TRG;
+ val |= BF_ANADIG_REG_CORE_REG2_TRG(0x1f);
+ REG_WR(ANATOP_BASE_ADDR, HW_ANADIG_REG_CORE, val);
+
+ /* Bypass the VDDCORE from Anatop */
+ val = REG_RD(ANATOP_BASE_ADDR, HW_ANADIG_REG_CORE);
+ val &= ~BM_ANADIG_REG_CORE_REG0_TRG;
+ val |= BF_ANADIG_REG_CORE_REG0_TRG(0x1f);
+ REG_WR(ANATOP_BASE_ADDR, HW_ANADIG_REG_CORE, val);
+
+ /* Bypass the VDDPU from Anatop */
+ val = REG_RD(ANATOP_BASE_ADDR, HW_ANADIG_REG_CORE);
+ val &= ~BM_ANADIG_REG_CORE_REG1_TRG;
+ val |= BF_ANADIG_REG_CORE_REG1_TRG(0x1f);
+ REG_WR(ANATOP_BASE_ADDR, HW_ANADIG_REG_CORE, val);
+
+ /*clear PowerDown Enable bit of WDOG1_WMCR*/
+ writew(0, WDOG1_BASE_ADDR + 0x08);
+ printf("hw_anadig_reg_core=%x\n",
+ REG_RD(ANATOP_BASE_ADDR, HW_ANADIG_REG_CORE));
+ #endif
+
+ }
+}
+#endif
+
int board_init(void)
{
mxc_iomux_v3_init((void *)IOMUXC_BASE_ADDR);
@@ -710,6 +1018,11 @@ int board_init(void)
int board_late_init(void)
{
+ #ifdef CONFIG_I2C_MXC
+ setup_i2c(CONFIG_SYS_I2C_PORT);
+ i2c_bus_recovery();
+ setup_pmic_voltages();
+ #endif
return 0;
}
diff --git a/include/configs/mx6sl_arm2.h b/include/configs/mx6sl_arm2.h
index c5b0892..a7117c4 100644
--- a/include/configs/mx6sl_arm2.h
+++ b/include/configs/mx6sl_arm2.h
@@ -93,6 +93,7 @@
#define CONFIG_BOOTP_DNS
#define CONFIG_CMD_SPI
+#define CONFIG_CMD_I2C
#define CONFIG_CMD_IMXOTP
/* Enable below configure when supporting nand */
@@ -263,6 +264,18 @@
#define CONFIG_ENV_IS_NOWHERE 1
#endif
+/*
+ * I2C Configs
+ */
+#ifdef CONFIG_CMD_I2C
+ #define CONFIG_HARD_I2C 1
+ #define CONFIG_I2C_MXC 1
+ #define CONFIG_SYS_I2C_PORT I2C1_BASE_ADDR
+ #define CONFIG_SYS_I2C_SPEED 100000
+ #define CONFIG_SYS_I2C_SLAVE 0x8
+ #define CONFIG_MX6_INTER_LDO_BYPASS 0
+#endif
+
/*#define CONFIG_SPLASH_SCREEN*/
/*
generated by cgit v1.1 at 2024-11-22 14:15:18 +0000