diff options
| -rw-r--r-- | include/configs/taihu.h | 44 |
1 files changed, 5 insertions, 39 deletions
diff --git a/include/configs/taihu.h b/include/configs/taihu.h index c51468b..d012c60 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -80,6 +80,7 @@ "bootfile=/tftpboot/taihu/uImage\0" \ "rootpath=/opt/eldk/ppc_4xx\0" \ "netdev=eth0\0" \ + "hostname=taihu\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -210,10 +211,12 @@ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ /*----------------------------------------------------------------------- * I2C stuff @@ -328,7 +331,7 @@ unsigned char spi_read(void); /*----------------------------------------------------------------------- * PPC405 GPIO Configuration */ -#define CFG_440_GPIO_TABLE { /* GPIO Alternate1 */ \ +#define CFG_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \ { \ /* GPIO Core 0 */ \ { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast SPI CS */ \ @@ -415,43 +418,6 @@ unsigned char spi_read(void); #define CFG_EBC_PB4AP 0x158FF600 #define CFG_EBC_PB4CR 0x5021A000 -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs - */ -#define CFG_GPIO0_OSRH 0x15555550 /* output select high/low */ -#define CFG_GPIO0_OSRL 0x00000110 -#define CFG_GPIO0_ISR1H 0x00000001 /* input select high/low */ -#define CFG_GPIO0_ISR1L 0x15545440 -#define CFG_GPIO0_TSRH 0x00000000 /* three-state select high/low */ -#define CFG_GPIO0_TSRL 0x00000000 -#define CFG_GPIO0_TCR 0xFFFE8117 /* three-state control */ -#define CFG_GPIO0_ODR 0x00000000 /* open drain */ - -#define GPIO0 0 /* GPIO controller 0 */ - -/* the GPIO macros in include/ppc405.h for High/Low registers are backwards */ - -#define GPIOx_OSL (GPIO0_OSRH-GPIO_BASE) -#define GPIOx_TSL (GPIO0_TSRH-GPIO_BASE) -#define GPIOx_IS1L (GPIO0_ISR1H-GPIO_BASE) -#define GPIOx_IS2L (GPIO0_ISR1H-GPIO_BASE) -#define GPIOx_IS3L (GPIO0_ISR1H-GPIO_BASE) - -#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO output select */ -#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO three-state select */ -#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO input select */ -#define GPIO_IS2(x) (x+GPIOx_IS1L) -#define GPIO_IS3(x) (x+GPIOx_IS1L) - #define CPLD_REG0_ADDR 0x50100000 #define CPLD_REG1_ADDR 0x50100001 /* |