summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--cpu/ppc4xx/44x_spd_ddr2.c41
-rw-r--r--cpu/ppc4xx/4xx_enet.c369
-rw-r--r--cpu/ppc4xx/4xx_pci.c9
-rw-r--r--cpu/ppc4xx/4xx_pcie.c203
-rw-r--r--cpu/ppc4xx/4xx_uart.c24
5 files changed, 553 insertions, 93 deletions
diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c
index 3bafea3..9e722b9 100644
--- a/cpu/ppc4xx/44x_spd_ddr2.c
+++ b/cpu/ppc4xx/44x_spd_ddr2.c
@@ -42,7 +42,8 @@
#include <asm/mmu.h>
#if defined(CONFIG_SPD_EEPROM) && \
- (defined(CONFIG_440SP) || defined(CONFIG_440SPE))
+ (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT))
/*-----------------------------------------------------------------------------+
* Defines
@@ -579,6 +580,13 @@ long int initdram(int board_type)
ppc440sp_sdram_register_dump();
+ /*
+ * Clear potential errors resulting from auto-calibration.
+ * If not done, then we could get an interrupt later on when
+ * exceptions are enabled.
+ */
+ set_mcsr(get_mcsr());
+
return dram_size;
}
@@ -2125,6 +2133,7 @@ static void program_memory_queue(unsigned long *dimm_populated,
unsigned long baseadd_size;
unsigned long i;
unsigned long bank_0_populated = 0;
+ unsigned long total_size = 0;
/*------------------------------------------------------------------
* Reset the rank_base_address.
@@ -2147,28 +2156,38 @@ static void program_memory_queue(unsigned long *dimm_populated,
* Set the sizes
*-----------------------------------------------------------------*/
baseadd_size = 0;
- rank_size_bytes = 4 * 1024 * 1024 * rank_size_id;
switch (rank_size_id) {
+ case 0x01:
+ baseadd_size |= SDRAM_RXBAS_SDSZ_1024;
+ total_size = 1024;
+ break;
case 0x02:
- baseadd_size |= SDRAM_RXBAS_SDSZ_8;
+ baseadd_size |= SDRAM_RXBAS_SDSZ_2048;
+ total_size = 2048;
break;
case 0x04:
- baseadd_size |= SDRAM_RXBAS_SDSZ_16;
+ baseadd_size |= SDRAM_RXBAS_SDSZ_4096;
+ total_size = 4096;
break;
case 0x08:
baseadd_size |= SDRAM_RXBAS_SDSZ_32;
+ total_size = 32;
break;
case 0x10:
baseadd_size |= SDRAM_RXBAS_SDSZ_64;
+ total_size = 64;
break;
case 0x20:
baseadd_size |= SDRAM_RXBAS_SDSZ_128;
+ total_size = 128;
break;
case 0x40:
baseadd_size |= SDRAM_RXBAS_SDSZ_256;
+ total_size = 256;
break;
case 0x80:
baseadd_size |= SDRAM_RXBAS_SDSZ_512;
+ total_size = 512;
break;
default:
printf("DDR-SDRAM: DIMM %d memory queue configuration.\n",
@@ -2178,6 +2197,7 @@ static void program_memory_queue(unsigned long *dimm_populated,
printf("Replace the DIMM module with a supported DIMM.\n\n");
spd_ddr_init_hang ();
}
+ rank_size_bytes = total_size << 20;
if ((dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_num == 1))
bank_0_populated = 1;
@@ -2190,6 +2210,19 @@ static void program_memory_queue(unsigned long *dimm_populated,
}
}
}
+
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ /*
+ * Enable high bandwidth access on 460EX/GT.
+ * This should/could probably be done on other
+ * PPC's too, like 440SPe.
+ * This is currently not used, but with this setup
+ * it is possible to use it later on in e.g. the Linux
+ * EMAC driver for performance gain.
+ */
+ mtdcr(SDRAM_PLBADDULL, 0x00000000); /* MQ0_BAUL */
+ mtdcr(SDRAM_PLBADDUHB, 0x00000008); /* MQ0_BAUH */
+#endif
}
/*-----------------------------------------------------------------------------+
diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c
index 599f5ce..d990250 100644
--- a/cpu/ppc4xx/4xx_enet.c
+++ b/cpu/ppc4xx/4xx_enet.c
@@ -137,17 +137,32 @@
#define BI_PHYMODE_RTBI 4
#define BI_PHYMODE_TBI 5
#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
#define BI_PHYMODE_SMII 6
#define BI_PHYMODE_MII 7
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define BI_PHYMODE_RMII 8
+#endif
#endif
#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
#define SDR0_MFR_ETH_CLK_SEL_V(n) ((0x01<<27) / (n+1))
#endif
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define SDR0_ETH_CFG_CLK_SEL_V(n) (0x01 << (8 + n))
+#endif
+
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define MAL_RX_CHAN_MUL 8 /* 460EX/GT uses MAL channel 8 for EMAC1 */
+#else
+#define MAL_RX_CHAN_MUL 1
+#endif
+
/*-----------------------------------------------------------------------------+
* Global variables. TX and RX descriptors and buffers.
*-----------------------------------------------------------------------------*/
@@ -214,6 +229,44 @@ extern int emac4xx_miiphy_write (char *devname, unsigned char addr,
int board_emac_count(void);
+static void emac_loopback_enable(EMAC_4XX_HW_PST hw_p)
+{
+#if defined(CONFIG_440SPE) || \
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_405EX)
+ u32 val;
+
+ mfsdr(sdr_mfr, val);
+ val |= SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum);
+ mtsdr(sdr_mfr, val);
+#elif defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ u32 val;
+
+ mfsdr(SDR0_ETH_CFG, val);
+ val |= SDR0_ETH_CFG_CLK_SEL_V(hw_p->devnum);
+ mtsdr(SDR0_ETH_CFG, val);
+#endif
+}
+
+static void emac_loopback_disable(EMAC_4XX_HW_PST hw_p)
+{
+#if defined(CONFIG_440SPE) || \
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_405EX)
+ u32 val;
+
+ mfsdr(sdr_mfr, val);
+ val &= ~SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum);
+ mtsdr(sdr_mfr, val);
+#elif defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ u32 val;
+
+ mfsdr(SDR0_ETH_CFG, val);
+ val &= ~SDR0_ETH_CFG_CLK_SEL_V(hw_p->devnum);
+ mtsdr(SDR0_ETH_CFG, val);
+#endif
+}
+
/*-----------------------------------------------------------------------------+
| ppc_4xx_eth_halt
| Disable MAL channel, and EMACn
@@ -222,11 +275,6 @@ static void ppc_4xx_eth_halt (struct eth_device *dev)
{
EMAC_4XX_HW_PST hw_p = dev->priv;
uint32_t failsafe = 10000;
-#if defined(CONFIG_440SPE) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_405EX)
- unsigned long mfr;
-#endif
out_be32((void *)EMAC_IER + hw_p->hw_addr, 0x00000000); /* disable emac interrupts */
@@ -247,27 +295,14 @@ static void ppc_4xx_eth_halt (struct eth_device *dev)
break;
}
- /* EMAC RESET */
-#if defined(CONFIG_440SPE) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_405EX)
/* provide clocks for EMAC internal loopback */
- mfsdr (sdr_mfr, mfr);
- mfr |= SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum);
- mtsdr(sdr_mfr, mfr);
-#endif
+ emac_loopback_enable(hw_p);
+ /* EMAC RESET */
out_be32((void *)EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
-#if defined(CONFIG_440SPE) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_405EX)
/* remove clocks for EMAC internal loopback */
- mfsdr (sdr_mfr, mfr);
- mfr &= ~SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum);
- mtsdr(sdr_mfr, mfr);
-#endif
-
+ emac_loopback_disable(hw_p);
#ifndef CONFIG_NETCONSOLE
hw_p->print_speed = 1; /* print speed message again next time */
@@ -452,6 +487,187 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
}
#endif /* CONFIG_405EX */
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
+{
+ u32 eth_cfg;
+ u32 zmiifer; /* ZMII0_FER reg. */
+ u32 rmiifer; /* RGMII0_FER reg. Bridge 0 */
+ u32 rmiifer1; /* RGMII0_FER reg. Bridge 1 */
+
+ zmiifer = 0;
+ rmiifer = 0;
+ rmiifer1 = 0;
+
+ /* TODO:
+ * NOTE: 460GT has 2 RGMII bridge cores:
+ * emac0 ------ RGMII0_BASE
+ * |
+ * emac1 -----+
+ *
+ * emac2 ------ RGMII1_BASE
+ * |
+ * emac3 -----+
+ *
+ * 460EX has 1 RGMII bridge core:
+ * and RGMII1_BASE is disabled
+ * emac0 ------ RGMII0_BASE
+ * |
+ * emac1 -----+
+ */
+
+ /*
+ * Right now only 2*RGMII is supported. Please extend when needed.
+ * sr - 2008-02-19
+ */
+ switch (9) {
+ case 1:
+ /* 1 MII - 460EX */
+ /* GMC0 EMAC4_0, ZMII Bridge */
+ zmiifer |= ZMII_FER_MII << ZMII_FER_V(0);
+ bis->bi_phymode[0] = BI_PHYMODE_MII;
+ bis->bi_phymode[1] = BI_PHYMODE_NONE;
+ bis->bi_phymode[2] = BI_PHYMODE_NONE;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ break;
+ case 2:
+ /* 2 MII - 460GT */
+ /* GMC0 EMAC4_0, GMC1 EMAC4_2, ZMII Bridge */
+ zmiifer |= ZMII_FER_MII << ZMII_FER_V(0);
+ zmiifer |= ZMII_FER_MII << ZMII_FER_V(2);
+ bis->bi_phymode[0] = BI_PHYMODE_MII;
+ bis->bi_phymode[1] = BI_PHYMODE_NONE;
+ bis->bi_phymode[2] = BI_PHYMODE_MII;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ break;
+ case 3:
+ /* 2 RMII - 460EX */
+ /* GMC0 EMAC4_0, GMC0 EMAC4_1, ZMII Bridge */
+ zmiifer |= ZMII_FER_RMII << ZMII_FER_V(0);
+ zmiifer |= ZMII_FER_RMII << ZMII_FER_V(1);
+ bis->bi_phymode[0] = BI_PHYMODE_RMII;
+ bis->bi_phymode[1] = BI_PHYMODE_RMII;
+ bis->bi_phymode[2] = BI_PHYMODE_NONE;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ break;
+ case 4:
+ /* 4 RMII - 460GT */
+ /* GMC0 EMAC4_0, GMC0 EMAC4_1, GMC1 EMAC4_2, GMC1, EMAC4_3 */
+ /* ZMII Bridge */
+ zmiifer |= ZMII_FER_RMII << ZMII_FER_V(0);
+ zmiifer |= ZMII_FER_RMII << ZMII_FER_V(1);
+ zmiifer |= ZMII_FER_RMII << ZMII_FER_V(2);
+ zmiifer |= ZMII_FER_RMII << ZMII_FER_V(3);
+ bis->bi_phymode[0] = BI_PHYMODE_RMII;
+ bis->bi_phymode[1] = BI_PHYMODE_RMII;
+ bis->bi_phymode[2] = BI_PHYMODE_RMII;
+ bis->bi_phymode[3] = BI_PHYMODE_RMII;
+ break;
+ case 5:
+ /* 2 SMII - 460EX */
+ /* GMC0 EMAC4_0, GMC0 EMAC4_1, ZMII Bridge */
+ zmiifer |= ZMII_FER_SMII << ZMII_FER_V(0);
+ zmiifer |= ZMII_FER_SMII << ZMII_FER_V(1);
+ bis->bi_phymode[0] = BI_PHYMODE_SMII;
+ bis->bi_phymode[1] = BI_PHYMODE_SMII;
+ bis->bi_phymode[2] = BI_PHYMODE_NONE;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ break;
+ case 6:
+ /* 4 SMII - 460GT */
+ /* GMC0 EMAC4_0, GMC0 EMAC4_1, GMC0 EMAC4_3, GMC0 EMAC4_3 */
+ /* ZMII Bridge */
+ zmiifer |= ZMII_FER_SMII << ZMII_FER_V(0);
+ zmiifer |= ZMII_FER_SMII << ZMII_FER_V(1);
+ zmiifer |= ZMII_FER_SMII << ZMII_FER_V(2);
+ zmiifer |= ZMII_FER_SMII << ZMII_FER_V(3);
+ bis->bi_phymode[0] = BI_PHYMODE_SMII;
+ bis->bi_phymode[1] = BI_PHYMODE_SMII;
+ bis->bi_phymode[2] = BI_PHYMODE_SMII;
+ bis->bi_phymode[3] = BI_PHYMODE_SMII;
+ break;
+ case 7:
+ /* This is the default mode that we want for board bringup - Maple */
+ /* 1 GMII - 460EX */
+ /* GMC0 EMAC4_0, RGMII Bridge 0 */
+ rmiifer |= RGMII_FER_MDIO(0);
+
+ if (devnum == 0) {
+ rmiifer |= RGMII_FER_GMII << RGMII_FER_V(2); /* CH0CFG - EMAC0 */
+ bis->bi_phymode[0] = BI_PHYMODE_GMII;
+ bis->bi_phymode[1] = BI_PHYMODE_NONE;
+ bis->bi_phymode[2] = BI_PHYMODE_NONE;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ } else {
+ rmiifer |= RGMII_FER_GMII << RGMII_FER_V(3); /* CH1CFG - EMAC1 */
+ bis->bi_phymode[0] = BI_PHYMODE_NONE;
+ bis->bi_phymode[1] = BI_PHYMODE_GMII;
+ bis->bi_phymode[2] = BI_PHYMODE_NONE;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ }
+ break;
+ case 8:
+ /* 2 GMII - 460GT */
+ /* GMC0 EMAC4_0, RGMII Bridge 0 */
+ /* GMC1 EMAC4_2, RGMII Bridge 1 */
+ rmiifer |= RGMII_FER_GMII << RGMII_FER_V(2); /* CH0CFG - EMAC0 */
+ rmiifer1 |= RGMII_FER_GMII << RGMII_FER_V(2); /* CH0CFG - EMAC2 */
+ rmiifer |= RGMII_FER_MDIO(0); /* enable MDIO - EMAC0 */
+ rmiifer1 |= RGMII_FER_MDIO(0); /* enable MDIO - EMAC2 */
+
+ bis->bi_phymode[0] = BI_PHYMODE_GMII;
+ bis->bi_phymode[1] = BI_PHYMODE_NONE;
+ bis->bi_phymode[2] = BI_PHYMODE_GMII;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ break;
+ case 9:
+ /* 2 RGMII - 460EX */
+ /* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */
+ rmiifer |= RGMII_FER_RGMII << RGMII_FER_V(2);
+ rmiifer |= RGMII_FER_RGMII << RGMII_FER_V(3);
+ rmiifer |= RGMII_FER_MDIO(0); /* enable MDIO - EMAC0 */
+
+ bis->bi_phymode[0] = BI_PHYMODE_RGMII;
+ bis->bi_phymode[1] = BI_PHYMODE_RGMII;
+ bis->bi_phymode[2] = BI_PHYMODE_NONE;
+ bis->bi_phymode[3] = BI_PHYMODE_NONE;
+ break;
+ case 10:
+ /* 4 RGMII - 460GT */
+ /* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */
+ /* GMC1 EMAC4_2, GMC1 EMAC4_3, RGMII Bridge 1 */
+ rmiifer |= RGMII_FER_RGMII << RGMII_FER_V(2);
+ rmiifer |= RGMII_FER_RGMII << RGMII_FER_V(3);
+ rmiifer1 |= RGMII_FER_RGMII << RGMII_FER_V(2);
+ rmiifer1 |= RGMII_FER_RGMII << RGMII_FER_V(3);
+ bis->bi_phymode[0] = BI_PHYMODE_RGMII;
+ bis->bi_phymode[1] = BI_PHYMODE_RGMII;
+ bis->bi_phymode[2] = BI_PHYMODE_RGMII;
+ bis->bi_phymode[3] = BI_PHYMODE_RGMII;
+ break;
+ default:
+ break;
+ }
+
+ /* Set EMAC for MDIO */
+ mfsdr(SDR0_ETH_CFG, eth_cfg);
+ eth_cfg |= SDR0_ETH_CFG_MDIO_SEL_EMAC0;
+ mtsdr(SDR0_ETH_CFG, eth_cfg);
+
+ out_be32((void *)RGMII_FER, rmiifer);
+#if defined(CONFIG_460GT)
+ out_be32((void *)RGMII_FER + RGMII1_BASE_OFFSET, rmiifer1);
+#endif
+
+ /* bypass the TAHOE0/TAHOE1 cores for U-Boot */
+ mfsdr(SDR0_ETH_CFG, eth_cfg);
+ eth_cfg |= (SDR0_ETH_CFG_TAHOE0_BYPASS | SDR0_ETH_CFG_TAHOE1_BYPASS);
+ mtsdr(SDR0_ETH_CFG, eth_cfg);
+
+ return 0;
+}
+#endif /* CONFIG_460EX || CONFIG_460GT */
+
static inline void *malloc_aligned(u32 size, u32 align)
{
return (void *)(((u32)malloc(size + align) + align - 1) &
@@ -472,19 +688,16 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
#if defined(CONFIG_440GX) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
sys_info_t sysinfo;
#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
int ethgroup = -1;
#endif
#endif
-#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_405EX)
- unsigned long mfr;
-#endif
u32 bd_cached;
u32 bd_uncached = 0;
#ifdef CONFIG_4xx_DCACHE
@@ -503,6 +716,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
#if defined(CONFIG_440GX) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
/* Need to get the OPB frequency so we can access the PHY */
get_sys_info (&sysinfo);
@@ -556,21 +770,12 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
out_be32((void *)ZMII_FER, 0);
udelay (100);
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_440GP) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
out_be32((void *)ZMII_FER, (ZMII_FER_RMII | ZMII_FER_MDI) << ZMII_FER_V (devnum));
-#elif defined(CONFIG_440GX) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
+#elif defined(CONFIG_440GX) || \
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
ethgroup = ppc_4xx_eth_setup_bridge(devnum, bis);
-#elif defined(CONFIG_440GP)
- /* set RMII mode */
- out_be32((void *)ZMII_FER, ZMII_RMII | ZMII_MDI0);
-#else
- if ((devnum == 0) || (devnum == 1)) {
- out_be32((void *)ZMII_FER, (ZMII_FER_SMII | ZMII_FER_MDI) << ZMII_FER_V (devnum));
- } else { /* ((devnum == 2) || (devnum == 3)) */
- out_be32((void *)ZMII_FER, ZMII_FER_MDI << ZMII_FER_V (devnum));
- out_be32((void *)RGMII_FER, ((RGMII_FER_RGMII << RGMII_FER_V (2)) |
- (RGMII_FER_RGMII << RGMII_FER_V (3))));
- }
#endif
out_be32((void *)ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum));
@@ -579,20 +784,17 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
ethgroup = ppc_4xx_eth_setup_bridge(devnum, bis);
#endif
- __asm__ volatile ("eieio");
+ sync();
- /* reset emac so we have access to the phy */
-#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_405EX)
/* provide clocks for EMAC internal loopback */
- mfsdr (sdr_mfr, mfr);
- mfr |= SDR0_MFR_ETH_CLK_SEL_V(devnum);
- mtsdr(sdr_mfr, mfr);
-#endif
+ emac_loopback_enable(hw_p);
+ /* EMAC RESET */
out_be32((void *)EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
+ /* remove clocks for EMAC internal loopback */
+ emac_loopback_disable(hw_p);
+
failsafe = 1000;
while ((in_be32((void *)EMAC_M0 + hw_p->hw_addr) & (EMAC_M0_SRST)) && failsafe) {
udelay (1000);
@@ -601,18 +803,10 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
if (failsafe <= 0)
printf("\nProblem resetting EMAC!\n");
-#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_405EX)
- /* remove clocks for EMAC internal loopback */
- mfsdr (sdr_mfr, mfr);
- mfr &= ~SDR0_MFR_ETH_CLK_SEL_V(devnum);
- mtsdr(sdr_mfr, mfr);
-#endif
-
#if defined(CONFIG_440GX) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
/* Whack the M1 register */
mode_reg = 0x0;
@@ -674,6 +868,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
#if defined(CONFIG_440GX) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
#if defined(CONFIG_CIS8201_PHY)
@@ -772,8 +967,10 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
hw_p->devnum);
}
-#if defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \
- !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX)
+#if defined(CONFIG_440) && \
+ !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \
+ !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) && \
+ !defined(CONFIG_460EX) && !defined(CONFIG_460GT)
#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
mfsdr(sdr_mfr, reg);
if (speed == 100) {
@@ -807,6 +1004,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
#endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */
#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
if (speed == 1000)
reg = (RGMII_SSR_SP_1000MBPS << RGMII_SSR_V (devnum));
@@ -819,12 +1017,17 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
return -1;
}
out_be32((void *)RGMII_SSR, reg);
+#if defined(CONFIG_460GT)
+ if ((devnum == 2) || (devnum == 3))
+ out_be32((void *)RGMII_SSR + RGMII1_BASE_OFFSET, reg);
+#endif
#endif
/* set the Mal configuration reg */
#if defined(CONFIG_440GX) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
mtdcr (malmcr, MAL_CR_PLBB | MAL_CR_OPBBL | MAL_CR_LEA |
MAL_CR_PLBLT_DEFAULT | MAL_CR_EOPIE | 0x00330000);
@@ -926,9 +1129,16 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
mtdcr (maltxbattr, 0x0);
mtdcr (malrxbattr, 0x0);
#endif
+
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ mtdcr (malrxctp8r, hw_p->rx);
+ /* set RX buffer size */
+ mtdcr (malrcbs8, ENET_MAX_MTU_ALIGNED / 16);
+#else
mtdcr (malrxctp1r, hw_p->rx_phys);
/* set RX buffer size */
mtdcr (malrcbs1, ENET_MAX_MTU_ALIGNED / 16);
+#endif
break;
#if defined (CONFIG_440GX)
case 2:
@@ -1087,7 +1297,7 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr,
hw_p->tx[hw_p->tx_slot].data_len = (short) len;
hw_p->tx[hw_p->tx_slot].ctrl |= MAL_TX_CTRL_READY;
- __asm__ volatile ("eieio");
+ sync();
out_be32((void *)EMAC_TXM0 + hw_p->hw_addr,
in_be32((void *)EMAC_TXM0 + hw_p->hw_addr) | EMAC_TXM0_GNP0);
@@ -1127,15 +1337,31 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr,
*/
#define UIC0MSR uic1msr
#define UIC0SR uic1sr
+#define UIC1MSR uic1msr
+#define UIC1SR uic1sr
+#elif defined(CONFIG_460EX) || defined(CONFIG_460GT)
+/*
+ * Hack: On 460EX/GT all enet irq sources are located on UIC2
+ * Needs some cleanup. --ag
+ */
+#define UIC0MSR uic2msr
+#define UIC0SR uic2sr
+#define UIC1MSR uic2msr
+#define UIC1SR uic2sr
#else
#define UIC0MSR uic0msr
#define UIC0SR uic0sr
+#define UIC1MSR uic1msr
+#define UIC1SR uic1sr
#endif
#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_405EX)
#define UICMSR_ETHX uic0msr
#define UICSR_ETHX uic0sr
+#elif defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define UICMSR_ETHX uic2msr
+#define UICSR_ETHX uic2sr
#else
#define UICMSR_ETHX uic1msr
#define UICSR_ETHX uic1sr
@@ -1173,7 +1399,7 @@ int enetInt (struct eth_device *dev)
serviced = 0;
my_uic0msr = mfdcr (UIC0MSR);
- my_uic1msr = mfdcr (uic1msr);
+ my_uic1msr = mfdcr (UIC1MSR);
#if defined(CONFIG_440GX)
my_uic2msr = mfdcr (uic2msr);
#endif
@@ -1219,7 +1445,7 @@ int enetInt (struct eth_device *dev)
if ((hw_p->emac_ier & emac_isr)
|| (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */
- mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
+ mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
mtdcr (UICSR_ETHX, UIC_ETH0); /* Clear */
return (rc); /* we had errors so get out */
}
@@ -1238,7 +1464,7 @@ int enetInt (struct eth_device *dev)
if ((hw_p->emac_ier & emac_isr)
|| (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */
- mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
+ mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
mtdcr (UICSR_ETHX, UIC_ETH1); /* Clear */
return (rc); /* we had errors so get out */
}
@@ -1256,7 +1482,7 @@ int enetInt (struct eth_device *dev)
if ((hw_p->emac_ier & emac_isr)
|| (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */
- mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
+ mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
mtdcr (uic2sr, UIC_ETH2);
return (rc); /* we had errors so get out */
}
@@ -1274,7 +1500,7 @@ int enetInt (struct eth_device *dev)
if ((hw_p->emac_ier & emac_isr)
|| (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) {
mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */
- mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
+ mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
mtdcr (uic2sr, UIC_ETH3);
return (rc); /* we had errors so get out */
}
@@ -1292,7 +1518,9 @@ int enetInt (struct eth_device *dev)
/* check for EOB on valid channels */
if (my_uic0msr & UIC_MRE) {
mal_rx_eob = mfdcr (malrxeobisr);
- if ((mal_rx_eob & (0x80000000 >> hw_p->devnum)) != 0) { /* call emac routine for channel x */
+ if ((mal_rx_eob &
+ (0x80000000 >> (hw_p->devnum * MAL_RX_CHAN_MUL)))
+ != 0) { /* call emac routine for channel x */
/* clear EOB
mtdcr(malrxeobisr, mal_rx_eob); */
enet_rcv (dev, emac_isr);
@@ -1303,7 +1531,7 @@ int enetInt (struct eth_device *dev)
}
mtdcr (UIC0SR, UIC_MRE); /* Clear */
- mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
+ mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */
switch (hw_p->devnum) {
case 0:
mtdcr (UICSR_ETHX, UIC_ETH0);
@@ -1468,7 +1696,7 @@ static void enet_rcv (struct eth_device *dev, unsigned long malisr)
int loop_count = 0;
rx_eob_isr = mfdcr (malrxeobisr);
- if ((0x80000000 >> hw_p->devnum) & rx_eob_isr) {
+ if ((0x80000000 >> (hw_p->devnum * MAL_RX_CHAN_MUL)) & rx_eob_isr) {
/* clear EOB */
mtdcr (malrxeobisr, rx_eob_isr);
@@ -1482,7 +1710,7 @@ static void enet_rcv (struct eth_device *dev, unsigned long malisr)
loop_count++;
handled++;
- data_len = (unsigned long) hw_p->rx[i].data_len; /* Get len */
+ data_len = (unsigned long) hw_p->rx[i].data_len & 0x0fff; /* Get len */
if (data_len) {
if (data_len > ENET_MAX_MTU) /* Check len */
data_len = 0;
@@ -1568,7 +1796,7 @@ static int ppc_4xx_eth_rx (struct eth_device *dev)
msr = mfmsr ();
mtmsr (msr & ~(MSR_EE));
- length = hw_p->rx[user_index].data_len;
+ length = hw_p->rx[user_index].data_len & 0x0fff;
/* Pass the packet up to the protocol layers. */
/* NetReceive(NetRxPackets[rxIdx], length - 4); */
@@ -1718,6 +1946,7 @@ int ppc_4xx_eth_initialize (bd_t * bis)
/* set the MAL IER ??? names may change with new spec ??? */
#if defined(CONFIG_440SPE) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
defined(CONFIG_405EX)
mal_ier =
MAL_IER_PT | MAL_IER_PRE | MAL_IER_PWE |
diff --git a/cpu/ppc4xx/4xx_pci.c b/cpu/ppc4xx/4xx_pci.c
index a5b9690..941d4dc 100644
--- a/cpu/ppc4xx/4xx_pci.c
+++ b/cpu/ppc4xx/4xx_pci.c
@@ -531,7 +531,8 @@ int pci_440_init (struct pci_controller *hose)
out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
#endif
-#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
out32r( PCIX0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */
out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */
#elif defined(PCIX0_BRDGOPT1)
@@ -549,7 +550,8 @@ int pci_440_init (struct pci_controller *hose)
out32r( PCIX0_POM0SA, 0 ); /* disable */
out32r( PCIX0_POM1SA, 0 ); /* disable */
out32r( PCIX0_POM2SA, 0 ); /* disable */
-#if defined(CONFIG_440SPE)
+#if defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
out32r( PCIX0_POM0LAL, 0x10000000 );
out32r( PCIX0_POM0LAH, 0x0000000c );
#else
@@ -586,7 +588,8 @@ void pci_init_board(void)
int busno;
busno = pci_440_init (&ppc440_hose);
-#if defined(CONFIG_440SPE)
+#if defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
pcie_setup_hoses(busno + 1);
#endif
}
diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c
index 3af9862..f9a1988 100644
--- a/cpu/ppc4xx/4xx_pcie.c
+++ b/cpu/ppc4xx/4xx_pcie.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2006 - 2007
+ * (C) Copyright 2006 - 2008
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* Copyright (c) 2005 Cisco Systems. All rights reserved.
@@ -31,7 +31,8 @@
#include <common.h>
#include <pci.h>
-#if (defined(CONFIG_440SPE) || defined(CONFIG_405EX)) && \
+#if (defined(CONFIG_440SPE) || defined(CONFIG_405EX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)) && \
defined(CONFIG_PCI)
#include <asm/4xx_pcie.h>
@@ -306,9 +307,8 @@ static int check_error(void)
int err = 0;
/* SDR0_PEGPLLLCT1 reset */
- if (!(valPE0 = SDR_READ(PESDR0_PLLLCT1) & 0x01000000)) {
+ if (!(valPE0 = SDR_READ(PESDR0_PLLLCT1) & 0x01000000))
printf("PCIE: SDR0_PEGPLLLCT1 reset error 0x%x\n", valPE0);
- }
valPE0 = SDR_READ(PESDR0_RCSSET);
valPE1 = SDR_READ(PESDR1_RCSSET);
@@ -400,7 +400,108 @@ int ppc4xx_init_pcie(void)
}
return 0;
}
-#else
+#endif
+
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+static void ppc4xx_setup_utl(u32 port)
+{
+ volatile void *utl_base = NULL;
+
+ /*
+ * Map UTL registers at 0x0801_n000 (4K 0xfff mask) PEGPLn_REGMSK
+ */
+ switch (port) {
+ case 0:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE0), U64_TO_U32_HIGH(CFG_PCIE0_UTLBASE));
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE0), U64_TO_U32_LOW(CFG_PCIE0_UTLBASE));
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE0), 0x00007001); /* BAM 11100000=4KB */
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE0), 0);
+ break;
+
+ case 1:
+ mtdcr(DCRN_PEGPL_REGBAH(PCIE1), U64_TO_U32_HIGH(CFG_PCIE0_UTLBASE));
+ mtdcr(DCRN_PEGPL_REGBAL(PCIE1), U64_TO_U32_LOW(CFG_PCIE0_UTLBASE)
+ + 0x1000);
+ mtdcr(DCRN_PEGPL_REGMSK(PCIE1), 0x00007001); /* BAM 11100000=4KB */
+ mtdcr(DCRN_PEGPL_SPECIAL(PCIE1), 0);
+ break;
+ }
+ utl_base = (unsigned int *)(CFG_PCIE_BASE + 0x1000 * port);
+
+ /*
+ * Set buffer allocations and then assert VRB and TXE.
+ */
+ out_be32(utl_base + PEUTL_PBCTL, 0x0800000c); /* PLBME, CRRE */
+ out_be32(utl_base + PEUTL_OUTTR, 0x08000000);
+ out_be32(utl_base + PEUTL_INTR, 0x02000000);
+ out_be32(utl_base + PEUTL_OPDBSZ, 0x04000000); /* OPD = 512 Bytes */
+ out_be32(utl_base + PEUTL_PBBSZ, 0x00000000); /* Max 512 Bytes */
+ out_be32(utl_base + PEUTL_IPHBSZ, 0x02000000);
+ out_be32(utl_base + PEUTL_IPDBSZ, 0x04000000); /* IPD = 512 Bytes */
+ out_be32(utl_base + PEUTL_RCIRQEN, 0x00f00000);
+ out_be32(utl_base + PEUTL_PCTL, 0x80800066); /* VRB,TXE,timeout=default */
+}
+
+/*
+ * TODO: double check PCI express SDR based on the latest user manual
+ * Some registers specified here no longer exist.. has to be
+ * updated based on the final EAS spec.
+ */
+static int check_error(void)
+{
+ u32 valPE0, valPE1;
+ int err = 0;
+
+ valPE0 = SDR_READ(SDRN_PESDR_RCSSET(0));
+ valPE1 = SDR_READ(SDRN_PESDR_RCSSET(1));
+
+ /* SDR0_PExRCSSET rstgu */
+ if (!(valPE0 & PESDRx_RCSSET_RSTGU) || !(valPE1 & PESDRx_RCSSET_RSTGU)) {
+ printf("PCIE: SDR0_PExRCSSET rstgu error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rstdl */
+ if (!(valPE0 & PESDRx_RCSSET_RSTDL) || !(valPE1 & PESDRx_RCSSET_RSTDL)) {
+ printf("PCIE: SDR0_PExRCSSET rstdl error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rstpyn */
+ if ((valPE0 & PESDRx_RCSSET_RSTPYN) || (valPE1 & PESDRx_RCSSET_RSTPYN)) {
+ printf("PCIE: SDR0_PExRCSSET rstpyn error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET hldplb */
+ if ((valPE0 & PESDRx_RCSSET_HLDPLB) || (valPE1 & PESDRx_RCSSET_HLDPLB)) {
+ printf("PCIE: SDR0_PExRCSSET hldplb error\n");
+ err = -1;
+ }
+
+ /* SDR0_PExRCSSET rdy */
+ if ((valPE0 & PESDRx_RCSSET_RDY) || (valPE1 & PESDRx_RCSSET_RDY)) {
+ printf("PCIE: SDR0_PExRCSSET rdy error\n");
+ err = -1;
+ }
+
+ return err;
+}
+
+/*
+ * Initialize PCI Express core as described in User Manual
+ * TODO: double check PE SDR PLL Register with the updated user manual.
+ */
+int ppc4xx_init_pcie(void)
+{
+ if (check_error())
+ return -1;
+
+ return 0;
+}
+#endif /* CONFIG_460EX */
+
+#if defined(CONFIG_405EX)
static void ppc4xx_setup_utl(u32 port)
{
u32 utl_base;
@@ -450,7 +551,7 @@ int ppc4xx_init_pcie(void)
*/
return 0;
}
-#endif
+#endif /* CONFIG_405EX */
/*
* Board-specific pcie initialization
@@ -511,6 +612,82 @@ int __ppc4xx_init_pcie_port_hw(int port, int rootport)
}
#endif /* CONFIG_440SPE */
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+int __ppc4xx_init_pcie_port_hw(int port, int rootport)
+{
+ u32 val = 1 << 24;
+ u32 utlset1;
+
+ if (rootport) {
+ val = PTYPE_ROOT_PORT << 20;
+ utlset1 = 0x21222222;
+ } else {
+ val = PTYPE_LEGACY_ENDPOINT << 20;
+ utlset1 = 0x20222222;
+ }
+
+ if (port == 0) {
+ val |= LNKW_X1 << 12;
+ } else {
+ val |= LNKW_X4 << 12;
+ utlset1 |= 0x00101101;
+ }
+
+ SDR_WRITE(SDRN_PESDR_DLPSET(port), val);
+ SDR_WRITE(SDRN_PESDR_UTLSET1(port), utlset1);
+ SDR_WRITE(SDRN_PESDR_UTLSET2(port), 0x01210000);
+
+ switch (port) {
+ case 0:
+ SDR_WRITE(PESDR0_L0CDRCTL, 0x00003230);
+ SDR_WRITE(PESDR0_L0DRV, 0x00000136);
+ SDR_WRITE(PESDR0_L0CLK, 0x00000006);
+
+ SDR_WRITE(PESDR0_PHY_CTL_RST,0x10000000);
+ break;
+
+ case 1:
+ SDR_WRITE(PESDR1_L0CDRCTL, 0x00003230);
+ SDR_WRITE(PESDR1_L1CDRCTL, 0x00003230);
+ SDR_WRITE(PESDR1_L2CDRCTL, 0x00003230);
+ SDR_WRITE(PESDR1_L3CDRCTL, 0x00003230);
+ SDR_WRITE(PESDR1_L0DRV, 0x00000136);
+ SDR_WRITE(PESDR1_L1DRV, 0x00000136);
+ SDR_WRITE(PESDR1_L2DRV, 0x00000136);
+ SDR_WRITE(PESDR1_L3DRV, 0x00000136);
+ SDR_WRITE(PESDR1_L0CLK, 0x00000006);
+ SDR_WRITE(PESDR1_L1CLK, 0x00000006);
+ SDR_WRITE(PESDR1_L2CLK, 0x00000006);
+ SDR_WRITE(PESDR1_L3CLK, 0x00000006);
+
+ SDR_WRITE(PESDR1_PHY_CTL_RST,0x10000000);
+ break;
+ }
+
+ SDR_WRITE(SDRN_PESDR_RCSSET(port), SDR_READ(SDRN_PESDR_RCSSET(port)) |
+ (PESDRx_RCSSET_RSTGU | PESDRx_RCSSET_RSTPYN));
+
+ /* Poll for PHY reset */
+ switch (port) {
+ case 0:
+ while (!(SDR_READ(PESDR0_RSTSTA) & 0x1))
+ udelay(10);
+ break;
+ case 1:
+ while (!(SDR_READ(PESDR1_RSTSTA) & 0x1))
+ udelay(10);
+ break;
+ }
+
+ SDR_WRITE(SDRN_PESDR_RCSSET(port),
+ (SDR_READ(SDRN_PESDR_RCSSET(port)) &
+ ~(PESDRx_RCSSET_RSTGU | PESDRx_RCSSET_RSTDL)) |
+ PESDRx_RCSSET_RSTPYN);
+
+ return 0;
+}
+#endif /* CONFIG_440SPE */
+
#if defined(CONFIG_405EX)
int __ppc4xx_init_pcie_port_hw(int port, int rootport)
{
@@ -564,12 +741,12 @@ __attribute__((weak, alias("__ppc4xx_init_pcie_port_hw")));
* range (hangs the core upon config transaction attempts when set
* otherwise) while revA uses c_nnnn_nnnn.
*
- * For revA:
+ * For 440SPe revA:
* PCIE0: 0xc_4000_0000
* PCIE1: 0xc_8000_0000
* PCIE2: 0xc_c000_0000
*
- * For revB:
+ * For 440SPe revB:
* PCIE0: 0xd_0000_0000
* PCIE1: 0xd_2000_0000
* PCIE2: 0xd_4000_0000
@@ -577,6 +754,10 @@ __attribute__((weak, alias("__ppc4xx_init_pcie_port_hw")));
* For 405EX:
* PCIE0: 0xa000_0000
* PCIE1: 0xc000_0000
+ *
+ * For 460EX/GT:
+ * PCIE0: 0xd_0000_0000
+ * PCIE1: 0xd_2000_0000
*/
static inline u64 ppc4xx_get_cfgaddr(int port)
{
@@ -609,6 +790,12 @@ static inline u64 ppc4xx_get_cfgaddr(int port)
}
}
#endif
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ if (port == 0)
+ return 0x0000000d00000000ULL;
+ else
+ return 0x0000000d20000000ULL;
+#endif
}
/*
diff --git a/cpu/ppc4xx/4xx_uart.c b/cpu/ppc4xx/4xx_uart.c
index 3d1124e..ffbc222 100644
--- a/cpu/ppc4xx/4xx_uart.c
+++ b/cpu/ppc4xx/4xx_uart.c
@@ -64,16 +64,22 @@ DECLARE_GLOBAL_DATA_PTR;
#if defined(CONFIG_440)
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
-#define UART0_BASE CFG_PERIPHERAL_BASE + 0x00000300
-#define UART1_BASE CFG_PERIPHERAL_BASE + 0x00000400
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define UART0_BASE (CFG_PERIPHERAL_BASE + 0x00000300)
+#define UART1_BASE (CFG_PERIPHERAL_BASE + 0x00000400)
#else
-#define UART0_BASE CFG_PERIPHERAL_BASE + 0x00000200
-#define UART1_BASE CFG_PERIPHERAL_BASE + 0x00000300
+#define UART0_BASE (CFG_PERIPHERAL_BASE + 0x00000200)
+#define UART1_BASE (CFG_PERIPHERAL_BASE + 0x00000300)
#endif
#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
-#define UART2_BASE CFG_PERIPHERAL_BASE + 0x00000600
+#define UART2_BASE (CFG_PERIPHERAL_BASE + 0x00000600)
+#endif
+
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define UART2_BASE (CFG_PERIPHERAL_BASE + 0x00000500)
+#define UART3_BASE (CFG_PERIPHERAL_BASE + 0x00000600)
#endif
#if defined(CONFIG_440GP)
@@ -94,11 +100,13 @@ DECLARE_GLOBAL_DATA_PTR;
#define UART1_SDR sdr_uart1
#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \
defined(CONFIG_440GR) || defined(CONFIG_440GRx) || \
- defined(CONFIG_440SP) || defined(CONFIG_440SPe)
+ defined(CONFIG_440SP) || defined(CONFIG_440SPe) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
#define UART2_SDR sdr_uart2
#endif
#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \
- defined(CONFIG_440GR) || defined(CONFIG_440GRx)
+ defined(CONFIG_440GR) || defined(CONFIG_440GRx) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)
#define UART3_SDR sdr_uart3
#endif
#define MFREG(a, d) mfsdr(a, d)
generated by cgit v1.1 at 2024-11-19 04:54:31 +0000