diff options
| -rw-r--r-- | Makefile | 19 | ||||
| -rw-r--r-- | doc/README.sbc8349 | 50 | ||||
| -rw-r--r-- | include/configs/sbc8349.h | 22 |
3 files changed, 64 insertions, 27 deletions
@@ -2380,8 +2380,23 @@ MPC837XERDB_config: unconfig MVBLM7_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc83xx mvblm7 matrix_vision -sbc8349_config: unconfig - @$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349 +sbc8349_config \ +sbc8349_PCI_33_config \ +sbc8349_PCI_66_config: unconfig + @mkdir -p $(obj)include + @if [ "$(findstring _PCI_,$@)" ] ; then \ + $(XECHO) -n "... PCI HOST at " ; \ + echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \ + fi ; \ + if [ "$(findstring _33_,$@)" ] ; then \ + $(XECHO) -n "33MHz... " ; \ + echo "#define PCI_33M" >>$(obj)include/config.h ; \ + fi ; \ + if [ "$(findstring _66_,$@)" ] ; then \ + $(XECHO) -n "66MHz... " ; \ + echo "#define PCI_66M" >>$(obj)include/config.h ; \ + fi ; + @$(MKCONFIG) -a sbc8349 ppc mpc83xx sbc8349 SIMPC8313_LP_config \ SIMPC8313_SP_config: unconfig diff --git a/doc/README.sbc8349 b/doc/README.sbc8349 index 908e768..2c35919 100644 --- a/doc/README.sbc8349 +++ b/doc/README.sbc8349 @@ -91,19 +91,37 @@ safety check before resetting the board upon completion of the reflash. PCI: ==== -This board and U-Boot have been tested with PCI built in, on a SBC8349 -and confirmed that the "pci" command showed the intel e1000 that was -present in the PCI slot. Note that if a 33MHz 32bit card is inserted -in the slot, then the whole board will clock down to a 33MHz base -clock instead of the default 66MHz. This will change the baud clocks -and mess up your serial console output. If you want to use a 33MHz PCI -card, then you should build a U-Boot with #undef PCI_66M in the -include/configs/sbc8349.h and store this to flash prior to powering down -the board and inserting the 33MHz PCI card. - -By default PCI support is disabled to better support very early -revision MPC834x chips with possible PCI issues. Also PCI support is -untested on the sbc8347 variants at this point in time. - - - Paul Gortmaker, 01/2007 +There are three configuration choices: + sbc8349_config + sbc8349_PCI_33_config + sbc8349_PCI_66_config + +The 1st does not enable CONFIG_PCI, and assumes that the PCI slot +will be left empty (M66EN high), and so the board will operate with +a base clock of 66MHz. Note that you need both PCI enabled in u-boot +and linux in order to have functional PCI under linux. The only +reason for choosing to not enable PCI would be if you had a very +early (rev 1.0) CPU with possible PCI issues. + +The second enables PCI support and builds for a 33MHz clock rate. Note +that if a 33MHz 32bit card is inserted in the slot, then the whole board +will clock down to a 33MHz base clock instead of the default 66MHz. This +will change the baud clocks and mess up your serial console output if you +were previously running at 66MHz. If you want to use a 33MHz PCI card, +then you should build a U-Boot with sbc8349_PCI_33_config and store this +to flash prior to powering down the board and inserting the 33MHz PCI +card. + +The third option builds PCI support in, and leaves the clocking at the +default 66MHz. This has been tested with an intel PCI-X e1000 card. +This is also the appropriate choice for people with a recent (non 1.0) +CPU who currently have the PCI slot physically empty, but intend to +possibly add a PCI-X card at a later date. + + => pci + Scanning PCI devices on bus 0 + BusDevFun VendorId DeviceId Device Class Sub-Class + _____________________________________________________________ + 00.00.00 0x1957 0x0080 Processor 0x20 + 00.11.00 0x8086 0x1026 Network controller 0x00 + => diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index 868bd54..088b283 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -40,24 +40,28 @@ #define CONFIG_MPC8349 1 /* MPC8349 specific */ #define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */ -#undef CONFIG_PCI /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */ #undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ -#define PCI_66M -#ifdef PCI_66M -#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ -#else +/* + * The default if PCI isn't enabled, or if no PCI clk setting is given + * is 66MHz; this is what the board defaults to when the PCI slot is + * physically empty. The board will automatically (i.e w/o jumpers) + * clock down to 33MHz if you insert a 33MHz PCI card. + */ +#ifdef PCI_33M #define CONFIG_83XX_CLKIN 33000000 /* in Hz */ +#else /* 66M */ +#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ #endif #ifndef CONFIG_SYS_CLK_FREQ -#ifdef PCI_66M -#define CONFIG_SYS_CLK_FREQ 66000000 -#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 -#else +#ifdef PCI_33M #define CONFIG_SYS_CLK_FREQ 33000000 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 +#else /* 66M */ +#define CONFIG_SYS_CLK_FREQ 66000000 +#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 #endif #endif |