diff options
| -rw-r--r-- | Makefile | 1 | ||||
| -rw-r--r-- | board/freescale/mx35_3stack/mx35_3stack.c | 8 | ||||
| -rw-r--r-- | include/configs/mx35_3stack_mfg.h | 244 |
3 files changed, 253 insertions, 0 deletions
@@ -3242,6 +3242,7 @@ mx31_3stack_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 mx31_3stack freescale mx31 mx35_3stack_config \ +mx35_3stack_mfg_config \ mx35_3stack_mmc_config: unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 mx35_3stack freescale mx35 diff --git a/board/freescale/mx35_3stack/mx35_3stack.c b/board/freescale/mx35_3stack/mx35_3stack.c index 4da8f25..c3c9683 100644 --- a/board/freescale/mx35_3stack/mx35_3stack.c +++ b/board/freescale/mx35_3stack/mx35_3stack.c @@ -149,6 +149,14 @@ int board_init(void) { int pad; +#ifdef CONFIG_MFG +/* MFG firmware need reset usb to avoid host crash firstly */ +#define USBCMD 0x53FF4140 + int val = readl(USBCMD); + val &= ~0x1; /*RS bit*/ + writel(val, USBCMD); +#endif + setup_soc_rev(); /* enable clocks */ diff --git a/include/configs/mx35_3stack_mfg.h b/include/configs/mx35_3stack_mfg.h new file mode 100644 index 0000000..42b5909 --- /dev/null +++ b/include/configs/mx35_3stack_mfg.h @@ -0,0 +1,244 @@ +/* + * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de> + * + * (C) Copyright 2008-2010 Freescale Semiconductor, Inc. + * + * Configuration settings for the MX35 3stack Freescale board. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/mx35.h> + + /* High Level Configuration Options */ +#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */ +#define CONFIG_MXC 1 +#define CONFIG_MX35 1 /* in a mx31 */ +#define CONFIG_MX35_HCLK_FREQ 24000000 /* RedBoot says 26MHz */ +#define CONFIG_MFG 1 + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define BOARD_LATE_INIT +/* + * Disabled for now due to build problems under Debian and a significant + * increase in the final file size: 144260 vs. 109536 Bytes. + */ +#if 0 +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 +#endif + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_REVISION_TAG 1 +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 512 * 1024) +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * Hardware drivers + */ +#define CONFIG_HARD_I2C 1 +#define CONFIG_I2C_MXC 1 +#define CONFIG_SYS_I2C_PORT I2C_BASE_ADDR +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0xfe + +#define CONFIG_MX35_UART UART1_BASE_ADDR + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} + +/*********************************************************** + * Command definition + ***********************************************************/ + +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +/*#define CONFIG_CMD_SPI*/ +/*#define CONFIG_CMD_DATE*/ +#define CONFIG_CMD_NAND +#define CONFIG_MXC_NAND + +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_NET_RETRY_COUNT 100 + +#define CONFIG_BOOTDELAY 0 + +#define CONFIG_LOADADDR 0x80100000 /* loadaddr env var */ + +#define CONFIG_BOOTARGS "console=ttymxc0,115200 "\ + "rdinit=/linuxrc" + +#define CONFIG_BOOTCOMMAND "bootm ${loadaddr} 0x80800000" + +#define CONFIG_ENV_IS_EMBEDDED + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "ethprime=smc911x\0" \ + "uboot_addr=0xa0000000\0" \ + "uboot=u-boot.bin\0" \ + "kernel=uImage\0" \ + "nfsroot=/opt/eldk/arm\0" \ + "bootargs_base=setenv bootargs console=ttymxc0,115200\0"\ + "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs "\ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0"\ + "bootcmd=run bootcmd_net\0" \ + "bootcmd_net=run bootargs_base bootargs_nfs; " \ + "tftpboot ${loadaddr} ${kernel}; bootm\0" \ + "prg_uboot=tftpboot ${loadaddr} ${uboot}; " \ + "protect off ${uboot_addr} 0xa003ffff; " \ + "erase ${uboot_addr} 0xa003ffff; " \ + "cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \ + "setenv filesize; saveenv\0" + +/*Support LAN9217*/ +#define CONFIG_SMC911X 1 +#define CONFIG_SMC911X_16_BIT 1 +#define CONFIG_SMC911X_BASE CS5_BASE_ADDR + +#define CONFIG_HAS_ETH1 +#define CONFIG_NET_MULTI 1 +#define CONFIG_ETHPRIME +#define CONFIG_MXC_FEC +#define CONFIG_MII +#define CONFIG_DISCOVER_PHY + +#define CONFIG_FEC0_IOBASE FEC_BASE_ADDR +#define CONFIG_FEC0_PINMUX -1 +#define CONFIG_FEC0_PHY_ADDR 0x1F +#define CONFIG_FEC0_MIIBASE -1 + +/* + * The MX31ADS board seems to have a hardware "peculiarity" confirmed under + * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A + * controller inverted. The controller is capable of detecting and correcting + * this, but it needs 4 network packets for that. Which means, at startup, you + * will not receive answers to the first 4 packest, unless there have been some + * broadcasts on the network, or your board is on a hub. Reducing the ARP + * timeout from default 5 seconds to 200ms we speed up the initial TFTP + * transfer, should the user wish one, significantly. + */ +#define CONFIG_ARP_TIMEOUT 200UL + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "MX35 U-Boot > " +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_ARCH_MMU +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x10000 + +#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_EDITING 1 + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 CSD0_BASE_ADDR +#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024) + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CONFIG_SYS_FLASH_BASE CS0_BASE_ADDR +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +/* Monitor at beginning of flash */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 256KiB */ + +#define CONFIG_ENV_SECT_SIZE (128 * 1024) +#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_OFFSET_REDUND (2 * 1024 * 1024) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + +#define CONFIG_ENV_IS_NOWHERE + +/* + * S29WS256N NOR flash has 4 32KiB small sectors at the beginning and at the + * end. The rest of 32MiB is in 128KiB big sectors. U-Boot occupies the low + * 4 sectors, if we put environment next to it, we will have to occupy 128KiB + * for it. Putting it at the top of flash we use only 32KiB. + */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_ENV_SECT_SIZE) + + +/*----------------------------------------------------------------------- + * CFI FLASH driver setup + */ +#define CONFIG_SYS_FLASH_CFI 1/* Flash memory is CFI compliant */ +#define CONFIG_FLASH_CFI_DRIVER 1/* Use drivers/cfi_flash.c */ +/* A non-standard buffered write algorithm */ +#define CONFIG_FLASH_SPANSION_S29WS_N 1 +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1/* Use buffered writes (~10x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION 1/* Use hardware sector protection */ + +/*----------------------------------------------------------------------- + * NAND FLASH driver setup + */ +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 +/* + * JFFS2 partitions + */ +#undef CONFIG_JFFS2_CMDLINE +#define CONFIG_JFFS2_DEV "nor0" + +#endif /* __CONFIG_H */ |