diff options
| -rw-r--r-- | board/esd/du440/du440.c | 5 | ||||
| -rw-r--r-- | board/esd/du440/du440.h | 1 | ||||
| -rw-r--r-- | include/configs/DU440.h | 16 |
3 files changed, 10 insertions, 12 deletions
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c index ceb128c..3dbb2e1 100644 --- a/board/esd/du440/du440.c +++ b/board/esd/du440/du440.c @@ -67,12 +67,12 @@ int board_early_init_f(void) out_be32((void*)GPIO1_OR, 0x00000000); out_be32((void*)GPIO1_TCR, 0xc2000000 | CFG_GPIO1_IORSTN | + CFG_GPIO1_IORST2N | CFG_GPIO1_LEDUSR1 | CFG_GPIO1_LEDUSR2 | CFG_GPIO1_LEDPOST | CFG_GPIO1_LEDDU); out_be32((void*)GPIO1_ODR, CFG_GPIO1_LEDDU); - out_be32((void*)GPIO1_OSRL, 0x5c280000); out_be32((void*)GPIO1_OSRH, 0x00000000); out_be32((void*)GPIO1_TSRL, 0x0c000000); @@ -243,7 +243,8 @@ int misc_init_r(void) * release IO-RST# * We have to wait at least 560ms until we may call usbhub_init */ - out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) | CFG_GPIO1_IORSTN); + out_be32((void*)GPIO1_OR, in_be32((void*)GPIO1_OR) | + CFG_GPIO1_IORSTN | CFG_GPIO1_IORST2N); /* * flash USR1/2 LEDs (600ms) diff --git a/board/esd/du440/du440.h b/board/esd/du440/du440.h index 5c362e4..83fdac7 100644 --- a/board/esd/du440/du440.h +++ b/board/esd/du440/du440.h @@ -24,6 +24,7 @@ #define CFG_GPIO1_DCF77 (0x80000000 >> (42-32)) /* GPIO1_42 */ #define CFG_GPIO1_IORSTN (0x80000000 >> (55-32)) /* GPIO1_55 */ +#define CFG_GPIO1_IORST2N (0x80000000 >> (47-32)) /* GPIO1_47 */ #define CFG_GPIO1_HWVER_MASK 0x000000f0 /* GPIO1_56-59 */ #define CFG_GPIO1_HWVER_SHIFT 4 diff --git a/include/configs/DU440.h b/include/configs/DU440.h index 4fb6921..f193a43 100644 --- a/include/configs/DU440.h +++ b/include/configs/DU440.h @@ -157,10 +157,9 @@ */ #define CFG_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */ #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#define CFG_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ + /* 440EPx errata CHIP 11 */ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ -#if 0 -#define CONFIG_ZERO_SDRAM /* Zero SDRAM after setup */ -#endif #define CONFIG_DDR_ECC /* Use ECC when available */ #define SPD_EEPROM_ADDRESS {0x50} #define CONFIG_PROG_SDRAM_TLB @@ -244,9 +243,6 @@ "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ "cp.b 100000 FFFA0000 60000\0" \ "" -#if 0 -#define CONFIG_BOOTCOMMAND "run flash_self" -#endif #define CONFIG_PREBOOT /* enable preboot variable */ @@ -264,7 +260,7 @@ int du440_phy_addr(int devnum); #define CONFIG_PHY_ADDR du440_phy_addr(0) /* PHY address */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_PHY_GIGE 1 /* Include GbE detection */ +#undef CONFIG_PHY_GIGE /* no GbE detection */ #define CONFIG_HAS_ETH0 #define CFG_RX_ETH_BUFFER 128 @@ -295,7 +291,9 @@ int du440_phy_addr(int devnum); #include <config_cmd_default.h> +#define CONFIG_CMD_AUTOSCRIPT #define CONFIG_CMD_BSP +#define CONFIG_CMD_BMP #define CONFIG_CMD_DATE #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP @@ -431,8 +429,6 @@ int du440_phy_addr(int devnum); #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -#if 0 -#define CONFIG_SHOW_ACTIVITY 1 -#endif +#define CONFIG_AUTOSCRIPT 1 #endif /* __CONFIG_H */ |