diff options
44 files changed, 2552 insertions, 2843 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index cbe5c47..b170111 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -420,6 +420,9 @@ Guennadi Liakhovetski <g.liakhovetski@gmx.de> linkstation MPC8241 +Feng Kan <fkan@amcc.com> + + redwood PPC4xx ------------------------------------------------------------------------- Unknown / orphaned boards: @@ -222,6 +222,7 @@ LIST_4xx=" \ PPChameleonEVB \ quad100hd \ rainier \ + redwood \ sbc405 \ sc3 \ sequoia \ @@ -1410,6 +1410,9 @@ PPChameleonEVB_HI_33_config: unconfig quad100hd_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx quad100hd +redwood_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx redwood amcc + sbc405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx sbc405 diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index f2bed5c..08d89d7 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -349,7 +349,7 @@ int is_pci_host(struct pci_controller *hose) return 1; } -int katmai_pcie_card_present(int port) +static int katmai_pcie_card_present(int port) { u32 val; @@ -437,76 +437,6 @@ void pcie_setup_hoses(int busno) } #endif /* defined(CONFIG_PCI) */ -int misc_init_f (void) -{ - uint reg; -#if defined(CONFIG_STRESS) - uint i ; - uint disp; -#endif - - /* minimal init for PCIe */ -#if 0 /* test-only: test endpoint at some time, for now rootpoint only */ - /* pci express 0 Endpoint Mode */ - mfsdr(SDR0_PE0DLPSET, reg); - reg &= (~0x00400000); - mtsdr(SDR0_PE0DLPSET, reg); -#else - /* pci express 0 Rootpoint Mode */ - mfsdr(SDR0_PE0DLPSET, reg); - reg |= 0x00400000; - mtsdr(SDR0_PE0DLPSET, reg); -#endif - /* pci express 1 Rootpoint Mode */ - mfsdr(SDR0_PE1DLPSET, reg); - reg |= 0x00400000; - mtsdr(SDR0_PE1DLPSET, reg); - /* pci express 2 Rootpoint Mode */ - mfsdr(SDR0_PE2DLPSET, reg); - reg |= 0x00400000; - mtsdr(SDR0_PE2DLPSET, reg); - -#if defined(CONFIG_STRESS) - /* - * All this setting done by linux only needed by stress an charac. test - * procedure - * PCIe 1 Rootpoint PCIe2 Endpoint - * PCIe 0 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level - */ - for (i=0,disp=0; i<8; i++,disp+=3) { - mfsdr(SDR0_PE0HSSSET1L0+disp, reg); - reg |= 0x33000000; - mtsdr(SDR0_PE0HSSSET1L0+disp, reg); - } - - /*PCIe 1 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level */ - for (i=0,disp=0; i<4; i++,disp+=3) { - mfsdr(SDR0_PE1HSSSET1L0+disp, reg); - reg |= 0x33000000; - mtsdr(SDR0_PE1HSSSET1L0+disp, reg); - } - - /*PCIE 2 FIR Pre-emphasis Filter Coefficients & Transmit Driver Power Level */ - for (i=0,disp=0; i<4; i++,disp+=3) { - mfsdr(SDR0_PE2HSSSET1L0+disp, reg); - reg |= 0x33000000; - mtsdr(SDR0_PE2HSSSET1L0+disp, reg); - } - - reg = 0x21242222; - mtsdr(SDR0_PE2UTLSET1, reg); - reg = 0x11000000; - mtsdr(SDR0_PE2UTLSET2, reg); - /* pci express 1 Endpoint Mode */ - reg = 0x00004000; - mtsdr(SDR0_PE2DLPSET, reg); - - mtsdr(SDR0_UART1, 0x2080005a); /* patch for TG */ -#endif - - return 0; -} - #ifdef CONFIG_POST /* * Returns 1 if keys pressed to start the power-on long-running tests diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c index eea1e1e..4d1d093 100644 --- a/board/amcc/ocotea/ocotea.c +++ b/board/amcc/ocotea/ocotea.c @@ -147,36 +147,48 @@ int board_early_init_f (void) /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - mtdcr (uic0er, 0x00000000); /* disable all */ - mtdcr (uic0cr, 0x00000009); /* SMI & UIC1 crit are critical */ - mtdcr (uic0pr, 0xfffffe13); /* per ref-board manual */ - mtdcr (uic0tr, 0x01c00008); /* per ref-board manual */ - mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - + /* + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic1er, 0x00000000); /* disable all */ - mtdcr (uic1cr, 0x00000000); /* all non-critical */ - mtdcr (uic1pr, 0xffffe0ff); /* per ref-board manual */ - mtdcr (uic1tr, 0x00ffc000); /* per ref-board manual */ + mtdcr (uic1cr, 0x00000009); /* SMI & UIC1 crit are critical */ + mtdcr (uic1pr, 0xfffffe13); /* per ref-board manual */ + mtdcr (uic1tr, 0x01c00008); /* per ref-board manual */ mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uic2er, 0x00000000); /* disable all */ mtdcr (uic2cr, 0x00000000); /* all non-critical */ - mtdcr (uic2pr, 0xffffffff); /* per ref-board manual */ - mtdcr (uic2tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic2pr, 0xffffe0ff); /* per ref-board manual */ + mtdcr (uic2tr, 0x00ffc000); /* per ref-board manual */ mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic2sr, 0xffffffff); /* clear all */ - mtdcr (uicb0sr, 0xfc000000); /* clear all */ - mtdcr (uicb0er, 0x00000000); /* disable all */ - mtdcr (uicb0cr, 0x00000000); /* all non-critical */ - mtdcr (uicb0pr, 0xfc000000); /* */ - mtdcr (uicb0tr, 0x00000000); /* */ - mtdcr (uicb0vr, 0x00000001); /* */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + mtdcr (uic3er, 0x00000000); /* disable all */ + mtdcr (uic3cr, 0x00000000); /* all non-critical */ + mtdcr (uic3pr, 0xffffffff); /* per ref-board manual */ + mtdcr (uic3tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic3vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + + mtdcr (uic0sr, 0xfc000000); /* clear all */ + mtdcr (uic0er, 0x00000000); /* disable all */ + mtdcr (uic0cr, 0x00000000); /* all non-critical */ + mtdcr (uic0pr, 0xfc000000); /* */ + mtdcr (uic0tr, 0x00000000); /* */ + mtdcr (uic0vr, 0x00000001); /* */ mfsdr (sdr_mfr, mfr); mfr &= ~SDR0_MFR_ECS_MASK; /* mtsdr(sdr_mfr, mfr); */ diff --git a/board/amcc/redwood/Makefile b/board/amcc/redwood/Makefile new file mode 100644 index 0000000..5793307 --- /dev/null +++ b/board/amcc/redwood/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2008 +# Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o +SOBJS = init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend *~ + +######################################################################### + +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/amcc/redwood/config.mk b/board/amcc/redwood/config.mk new file mode 100644 index 0000000..f33336d --- /dev/null +++ b/board/amcc/redwood/config.mk @@ -0,0 +1,42 @@ +# +# (C) Copyright 2008 +# Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# AMCC 460SX Reference Platform (redwood) board +# + +ifeq ($(ramsym),1) +TEXT_BASE = 0x07FD0000 +else +TEXT_BASE = 0xfffb0000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000 +endif diff --git a/board/amcc/redwood/init.S b/board/amcc/redwood/init.S new file mode 100644 index 0000000..fcffada --- /dev/null +++ b/board/amcc/redwood/init.S @@ -0,0 +1,77 @@ +/* + * (C) Copyright 2008 + * Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <ppc_asm.tmpl> +#include <config.h> +#include <asm-ppc/mmu.h> + +/************************************************************************** + * TLB TABLE + * + * This table is used by the cpu boot code to setup the initial tlb + * entries. Rather than make broad assumptions in the cpu source tree, + * this table lets each board set things up however they like. + * + * Pointer to the table is returned in r1 + * + *************************************************************************/ + + .section .bootpg,"ax" + .globl tlbtab +tlbtab: + tlbtab_start + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_R|AC_W|AC_X|SA_G) + + /* + * TLB entries for SDRAM are not needed on this platform. + * They are dynamically generated in the SPD DDR(2) detection + * routine. + */ + + /* Although 512 KB, map 256k at a time */ + tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I) + tlbentry(CFG_ISRAM_BASE + 0x40000, SZ_256K, 0x00040000, 4, AC_R|AC_W|AC_X|SA_I) + + tlbentry(CFG_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_R|AC_W|AC_X|SA_G|SA_I) + + /* + * Peripheral base + */ + tlbentry(CFG_PERIPHERAL_BASE, SZ_16K, 0xEF600000, 4, AC_R|AC_W|SA_G|SA_I) + + tlbentry(CFG_PCIE0_XCFGBASE,SZ_16M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I) + tlbentry(CFG_PCIE1_XCFGBASE,SZ_16M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I) + tlbentry(CFG_PCIE2_XCFGBASE,SZ_16M, 0x20000000, 0xC, AC_R|AC_W|SA_G|SA_I) + + tlbentry(CFG_PCIE0_MEMBASE, SZ_256M, 0x00000000, 0xD, AC_R|AC_W|SA_G|SA_I) + tlbentry(CFG_PCIE1_MEMBASE, SZ_256M, 0x00000000, 0xE, AC_R|AC_W|SA_G|SA_I) + + tlbentry(CFG_PCIE0_REGBASE, SZ_64K, 0x30000000, 0xC, AC_R|AC_W|SA_G|SA_I) + tlbentry(CFG_PCIE1_REGBASE, SZ_64K, 0x30010000, 0xC, AC_R|AC_W|SA_G|SA_I) + tlbentry(CFG_PCIE2_REGBASE, SZ_64K, 0x30020000, 0xC, AC_R|AC_W|SA_G|SA_I) + tlbtab_end diff --git a/board/amcc/redwood/redwood.c b/board/amcc/redwood/redwood.c new file mode 100644 index 0000000..37a0c31 --- /dev/null +++ b/board/amcc/redwood/redwood.c @@ -0,0 +1,456 @@ +/* + * This is the main board level file for the Redwood AMCC board. + * + * (C) Copyright 2008 + * Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <common.h> +#include "redwood.h" +#include <ppc4xx.h> +#include <asm/processor.h> +#include <i2c.h> +#include <asm-ppc/io.h> + +int compare_to_true(char *str); +char *remove_l_w_space(char *in_str); +char *remove_t_w_space(char *in_str); +int get_console_port(void); + +static void early_init_EBC(void); +static int bootdevice_selected(void); +static void early_reinit_EBC(int); +static void early_init_UIC(void); + +/* + * Define Boot devices + */ +#define BOOT_FROM_8BIT_SRAM 0x00 +#define BOOT_FROM_16BIT_SRAM 0x01 +#define BOOT_FROM_32BIT_SRAM 0x02 +#define BOOT_FROM_8BIT_NAND 0x03 +#define BOOT_FROM_16BIT_NOR 0x04 +#define BOOT_DEVICE_UNKNOWN 0xff + +/* + * EBC Devices Characteristics + * Peripheral Bank Access Parameters - EBC_BxAP + * Peripheral Bank Configuration Register - EBC_BxCR + */ + +/* + * 8 bit width SRAM + * BU Value + * BxAP : 0x03800000 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000 + * B0CR : 0xff098000 - BAS = ff0 - 100 11 00 0000000000000 + * B2CR : 0xe7098000 - BAS = e70 - 100 11 00 0000000000000 + */ +#define EBC_BXAP_8BIT_SRAM \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED + +#define EBC_BXAP_16BIT_SRAM EBC_BXAP_8BIT_SRAM +#define EBC_BXAP_32BIT_SRAM EBC_BXAP_8BIT_SRAM + +/* + * NAND flash + * BU Value + * BxAP : 0x048ff240 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000 + * B0CR : 0xff09a000 - BAS = ff0 - 100 11 01 0000000000000 + * B2CR : 0xe709a000 - BAS = e70 - 100 11 01 0000000000000 +*/ +#define EBC_BXAP_NAND \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED + +/* + * NOR flash + * BU Value + * BxAP : 0x048ff240 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000 + * B0CR : 0xff09a000 - BAS = ff0 - 100 11 01 0000000000000 + * B2CR : 0xe709a000 - BAS = e70 - 100 11 01 0000000000000 +*/ +#define EBC_BXAP_NOR \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED + +/* + * FPGA + * BU value : + * B1AP = 0x05895240 - 0 00001011 0 00 10 01 01 01 001 0 0 1 0 00000 + * B1CR = 0xe201a000 - BAS = e20 - 000 11 01 00000000000000 + */ +#define EBC_BXAP_FPGA \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(11) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(10) | EBC_BXAP_OEN_ENCODE(1) | \ + EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1) | \ + EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_RW | \ + EBC_BXAP_PEN_DISABLED + +#define EBC_BXCR_8BIT_SRAM_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFFE00000) | EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_32BIT_SRAM_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFFC00000) | EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT + +#define EBC_BXCR_NAND_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFF000000) | EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_16BIT_SRAM_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFFE00000) | EBC_BXCR_BS_2MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_NOR_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFF000000) | EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_NOR_CS1 \ + EBC_BXCR_BAS_ENCODE(0xE0000000) | EBC_BXCR_BS_128MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_NAND_CS1 \ + EBC_BXCR_BAS_ENCODE(0xE0000000) | EBC_BXCR_BS_128MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_NAND_CS2 \ + EBC_BXCR_BAS_ENCODE(0xC0000000) | EBC_BXCR_BS_128MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_SRAM_CS2 \ + EBC_BXCR_BAS_ENCODE(0xC0000000) | EBC_BXCR_BS_4MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT + +#define EBC_BXCR_LARGE_FLASH_CS2 \ + EBC_BXCR_BAS_ENCODE(0xE7000000) | EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_FPGA_CS3 \ + EBC_BXCR_BAS_ENCODE(0xE2000000) | EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +/***************************************************************************** + * UBOOT initiated board specific function calls + ****************************************************************************/ + +int board_early_init_f(void) +{ + int computed_boot_device = BOOT_DEVICE_UNKNOWN; + + /* + * Initialise EBC + */ + early_init_EBC(); + + /* + * Determine which boot device was selected + */ + computed_boot_device = bootdevice_selected(); + + /* + * Reinit EBC based on selected boot device + */ + early_reinit_EBC(computed_boot_device); + + /* + * Setup for UIC on 460SX redwood board + */ + early_init_UIC(); + + return 0; +} + +int checkboard(void) +{ + char *s = getenv("serial#"); + + printf("Board: Redwood - AMCC 460SX Reference Board"); + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + return 0; +} + +static void early_init_EBC(void) +{ + /* + * Initialize EBC CONFIG - + * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC + * default value : + * 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000 + */ + mtebc(xbcfg, EBC_CFG_LE_UNLOCK | + EBC_CFG_PTD_ENABLE | + EBC_CFG_RTC_16PERCLK | + EBC_CFG_ATC_PREVIOUS | + EBC_CFG_DTC_PREVIOUS | + EBC_CFG_CTC_PREVIOUS | + EBC_CFG_OEO_PREVIOUS | + EBC_CFG_EMC_DEFAULT | EBC_CFG_PME_DISABLE | EBC_CFG_PR_16); + + /* + * PART 1 : Initialize EBC Bank 3 + * ============================== + * Bank1 is always associated to the EPLD. + * It has to be initialized prior to other banks settings computation + * since some board registers values may be needed to determine the + * boot type + */ + mtebc(pb1ap, EBC_BXAP_FPGA); + mtebc(pb1cr, EBC_BXCR_FPGA_CS3); + +} + +static int bootdevice_selected(void) +{ + unsigned long sdr0_pinstp; + unsigned long bootstrap_settings; + int computed_boot_device = BOOT_DEVICE_UNKNOWN; + + /* + * Determine which boot device was selected + * ================================================= + * + * Read Pin Strap Register in PPC460SX + * Result can either be : + * - Boot strap = boot from EBC 8bits => Small Flash + * - Boot strap = boot from PCI + * - Boot strap = IIC + * In case of boot from IIC, read Serial Device Strap Register1 + * + * Result can either be : + * - Boot from EBC - EBC Bus Width = 8bits => Small Flash + * - Boot from EBC - EBC Bus Width = 16bits => Large Flash or SRAM + * - Boot from PCI + */ + + /* Read Pin Strap Register in PPC460SX */ + mfsdr(SDR0_PINSTP, sdr0_pinstp); + bootstrap_settings = sdr0_pinstp & SDR0_PSTRP0_BOOTSTRAP_MASK; + + switch (bootstrap_settings) { + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS0: + /* + * Boot from SRAM, 8bit width + */ + computed_boot_device = BOOT_FROM_8BIT_SRAM; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS1: + /* + * Boot from SRAM, 32bit width + */ + computed_boot_device = BOOT_FROM_32BIT_SRAM; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS2: + /* + * Boot from NAND, 8bit width + */ + computed_boot_device = BOOT_FROM_8BIT_NAND; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS4: + /* + * Boot from SRAM, 16bit width + * Boot setting in IIC EEPROM 0x50 + */ + computed_boot_device = BOOT_FROM_16BIT_SRAM; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS5: + /* + * Boot from NOR, 16bit width + * Boot setting in IIC EEPROM 0x54 + */ + computed_boot_device = BOOT_FROM_16BIT_NOR; + break; + default: + /* should not be */ + computed_boot_device = BOOT_DEVICE_UNKNOWN; + break; + } + + return computed_boot_device; +} + +static void early_reinit_EBC(int computed_boot_device) +{ + /* + * Compute EBC settings depending on selected boot device + * ====================================================== + * + * Resulting EBC init will be among following configurations : + * + * - Boot from EBC 8bits => boot from Small Flash selected + * EBC-CS0 = Small Flash + * EBC-CS2 = Large Flash and SRAM + * + * - Boot from EBC 16bits => boot from Large Flash or SRAM + * EBC-CS0 = Large Flash or SRAM + * EBC-CS2 = Small Flash + * + * - Boot from PCI + * EBC-CS0 = not initialized to avoid address contention + * EBC-CS2 = same as boot from Small Flash selected + */ + + unsigned long ebc0_cs0_bxap_value = 0, ebc0_cs0_bxcr_value = 0; + unsigned long ebc0_cs1_bxap_value = 0, ebc0_cs1_bxcr_value = 0; + unsigned long ebc0_cs2_bxap_value = 0, ebc0_cs2_bxcr_value = 0; + + switch (computed_boot_device) { + /*-------------------------------------------------------------------*/ + case BOOT_FROM_8BIT_SRAM: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_8BIT_SRAM; + ebc0_cs0_bxcr_value = EBC_BXCR_8BIT_SRAM_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_NAND; + ebc0_cs2_bxcr_value = EBC_BXCR_NAND_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_16BIT_SRAM: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_16BIT_SRAM; + ebc0_cs0_bxcr_value = EBC_BXCR_16BIT_SRAM_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_NAND; + ebc0_cs2_bxcr_value = EBC_BXCR_NAND_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_32BIT_SRAM: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_32BIT_SRAM; + ebc0_cs0_bxcr_value = EBC_BXCR_32BIT_SRAM_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_NAND; + ebc0_cs2_bxcr_value = EBC_BXCR_NAND_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_16BIT_NOR: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_NOR; + ebc0_cs0_bxcr_value = EBC_BXCR_NOR_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NAND; + ebc0_cs1_bxcr_value = EBC_BXCR_NAND_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_32BIT_SRAM; + ebc0_cs2_bxcr_value = EBC_BXCR_SRAM_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_8BIT_NAND: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_NAND; + ebc0_cs0_bxcr_value = EBC_BXCR_NAND_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_32BIT_SRAM; + ebc0_cs2_bxcr_value = EBC_BXCR_SRAM_CS2; + break; + + /*-------------------------------------------------------------------*/ + default: + /*-------------------------------------------------------------------*/ + /* BOOT_DEVICE_UNKNOWN */ + break; + } + + mtebc(pb0ap, ebc0_cs0_bxap_value); + mtebc(pb0cr, ebc0_cs0_bxcr_value); + mtebc(pb1ap, ebc0_cs1_bxap_value); + mtebc(pb1cr, ebc0_cs1_bxcr_value); + mtebc(pb2ap, ebc0_cs2_bxap_value); + mtebc(pb2cr, ebc0_cs2_bxcr_value); +} + +static void early_init_UIC(void) +{ + /* + * Initialise UIC registers. Clear all interrupts. Disable all + * interrupts. + * Set critical interrupt values. Set interrupt polarities. Set + * interrupt trigger levels. Make bit 0 High priority. Clear all + * interrupts again. + */ + mtdcr(uic3sr, 0xffffffff); /* Clear all interrupts */ + mtdcr(uic3er, 0x00000000); /* disable all interrupts */ + mtdcr(uic3cr, 0x00000000); /* Set Critical / Non Critical + * interrupts */ + mtdcr(uic3pr, 0xffffffff); /* Set Interrupt Polarities */ + mtdcr(uic3tr, 0x001fffff); /* Set Interrupt Trigger Levels */ + mtdcr(uic3vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic3sr, 0xffffffff); /* clear all interrupts */ + + mtdcr(uic2sr, 0xffffffff); /* Clear all interrupts */ + mtdcr(uic2er, 0x00000000); /* disable all interrupts */ + mtdcr(uic2cr, 0x00000000); /* Set Critical / Non Critical + * interrupts */ + mtdcr(uic2pr, 0xebebebff); /* Set Interrupt Polarities */ + mtdcr(uic2tr, 0x74747400); /* Set Interrupt Trigger Levels */ + mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic2sr, 0xffffffff); /* clear all interrupts */ + + mtdcr(uic1sr, 0xffffffff); /* Clear all interrupts */ + mtdcr(uic1er, 0x00000000); /* disable all interrupts */ + mtdcr(uic1cr, 0x00000000); /* Set Critical / Non Critical + * interrupts */ + mtdcr(uic1pr, 0xffffffff); /* Set Interrupt Polarities */ + mtdcr(uic1tr, 0x001fc0ff); /* Set Interrupt Trigger Levels */ + mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic1sr, 0xffffffff); /* clear all interrupts */ + + mtdcr(uic0sr, 0xffffffff); /* Clear all interrupts */ + mtdcr(uic0er, 0x00000000); /* disable all interrupts excepted + * cascade to be checked */ + mtdcr(uic0cr, 0x00104001); /* Set Critical / Non Critical + * interrupts */ + mtdcr(uic0pr, 0xffffffff); /* Set Interrupt Polarities */ + mtdcr(uic0tr, 0x000f003c); /* Set Interrupt Trigger Levels */ + mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic0sr, 0xffffffff); /* clear all interrupts */ + +} diff --git a/board/amcc/redwood/redwood.h b/board/amcc/redwood/redwood.h new file mode 100644 index 0000000..89b87e6 --- /dev/null +++ b/board/amcc/redwood/redwood.h @@ -0,0 +1,50 @@ +/* + * (C) Copyright 2008 + * Feng Kan, Applied Micro Circuit Corp., fkan@amcc.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __REDWOOD_H_ +#define __REDWOOD_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +/*----------------------------------------------------------------------------+ +| Defines ++----------------------------------------------------------------------------*/ +/* Pin Straps Reg */ +#define SDR0_PSTRP0 0x0040 +#define SDR0_PSTRP0_BOOTSTRAP_MASK 0xE0000000 /* Strap Bits */ + +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS1 0x20000000 /* Default strap settings 1 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS2 0x40000000 /* Default strap settings 2 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS3 0x60000000 /* Default strap settings 3 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS4 0x80000000 /* Default strap settings 4 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS5 0xA0000000 /* Default strap settings 5 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS6 0xC0000000 /* Default strap settings 6 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS7 0xE0000000 /* Default strap settings 7 */ + +#ifdef __cplusplus +} +#endif +#endif /* __REDWOOD_H_ */ diff --git a/board/amcc/redwood/u-boot.lds b/board/amcc/redwood/u-boot.lds new file mode 100644 index 0000000..2104cc2 --- /dev/null +++ b/board/amcc/redwood/u-boot.lds @@ -0,0 +1,147 @@ +/* + * (C) Copyright 2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/ppc4xx/start.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/ppc4xx/start.o (.text) + board/amcc/redwood/init.o (.text) + +/* . = env_offset;*/ +/* common/environment.o(.text)*/ + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c index b833092..d7d2aa2 100644 --- a/board/amcc/sequoia/sequoia.c +++ b/board/amcc/sequoia/sequoia.c @@ -25,12 +25,11 @@ #include <common.h> #include <libfdt.h> #include <fdt_support.h> -#include <ppc440.h> +#include <ppc4xx.h> #include <asm/gpio.h> #include <asm/processor.h> #include <asm/io.h> #include <asm/bitops.h> -#include <asm/ppc4xx-intvec.h> DECLARE_GLOBAL_DATA_PTR; @@ -335,7 +334,7 @@ int checkboard(void) */ void sequoia_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev) { - pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIR2); + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2); } #endif diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c index b6c3065..fdd82e7 100644 --- a/board/amcc/taishan/taishan.c +++ b/board/amcc/taishan/taishan.c @@ -119,36 +119,48 @@ int board_early_init_f (void) /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - mtdcr (uic0er, 0x00000000); /* disable all */ - mtdcr (uic0cr, 0x00000009); /* SMI & UIC1 crit are critical */ - mtdcr (uic0pr, 0xfffffe13); /* per ref-board manual */ - mtdcr (uic0tr, 0x01c00008); /* per ref-board manual */ - mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - + /* + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic1er, 0x00000000); /* disable all */ - mtdcr (uic1cr, 0x00000000); /* all non-critical */ - mtdcr (uic1pr, 0xffffe0ff); /* per ref-board manual */ - mtdcr (uic1tr, 0x00ffc000); /* per ref-board manual */ + mtdcr (uic1cr, 0x00000009); /* SMI & UIC1 crit are critical */ + mtdcr (uic1pr, 0xfffffe13); /* per ref-board manual */ + mtdcr (uic1tr, 0x01c00008); /* per ref-board manual */ mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uic2er, 0x00000000); /* disable all */ mtdcr (uic2cr, 0x00000000); /* all non-critical */ - mtdcr (uic2pr, 0xffffffff); /* per ref-board manual */ - mtdcr (uic2tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic2pr, 0xffffe0ff); /* per ref-board manual */ + mtdcr (uic2tr, 0x00ffc000); /* per ref-board manual */ mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic2sr, 0xffffffff); /* clear all */ - mtdcr (uicb0sr, 0xfc000000); /* clear all */ - mtdcr (uicb0er, 0x00000000); /* disable all */ - mtdcr (uicb0cr, 0x00000000); /* all non-critical */ - mtdcr (uicb0pr, 0xfc000000); /* */ - mtdcr (uicb0tr, 0x00000000); /* */ - mtdcr (uicb0vr, 0x00000001); /* */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + mtdcr (uic3er, 0x00000000); /* disable all */ + mtdcr (uic3cr, 0x00000000); /* all non-critical */ + mtdcr (uic3pr, 0xffffffff); /* per ref-board manual */ + mtdcr (uic3tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic3vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + + mtdcr (uic0sr, 0xfc000000); /* clear all */ + mtdcr (uic0er, 0x00000000); /* disable all */ + mtdcr (uic0cr, 0x00000000); /* all non-critical */ + mtdcr (uic0pr, 0xfc000000); /* */ + mtdcr (uic0tr, 0x00000000); /* */ + mtdcr (uic0vr, 0x00000001); /* */ /* Enable two GPIO 10~11 and TraceA signal */ mfsdr(sdr_pfc0,reg); diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c index 6608893..84c3938 100644 --- a/board/amcc/yucca/yucca.c +++ b/board/amcc/yucca/yucca.c @@ -677,7 +677,7 @@ int is_pci_host(struct pci_controller *hose) return 1; } -int yucca_pcie_card_present(int port) +static int yucca_pcie_card_present(int port) { u16 reg; @@ -879,10 +879,6 @@ void pcie_setup_hoses(int busno) int misc_init_f (void) { uint reg; -#if defined(CONFIG_STRESS) - uint i ; - uint disp; -#endif out16(FPGA_REG10, (in16(FPGA_REG10) & ~(FPGA_REG10_AUTO_NEG_DIS|FPGA_REG10_RESET_ETH)) | @@ -897,67 +893,23 @@ int misc_init_f (void) /* minimal init for PCIe */ /* pci express 0 Endpoint Mode */ - mfsdr(SDR0_PE0DLPSET, reg); + mfsdr(SDRN_PESDR_DLPSET(0), reg); reg &= (~0x00400000); - mtsdr(SDR0_PE0DLPSET, reg); + mtsdr(SDRN_PESDR_DLPSET(0), reg); /* pci express 1 Rootpoint Mode */ - mfsdr(SDR0_PE1DLPSET, reg); + mfsdr(SDRN_PESDR_DLPSET(1), reg); reg |= 0x00400000; - mtsdr(SDR0_PE1DLPSET, reg); + mtsdr(SDRN_PESDR_DLPSET(1), reg); /* pci express 2 Rootpoint Mode */ - mfsdr(SDR0_PE2DLPSET, reg); + mfsdr(SDRN_PESDR_DLPSET(2), reg); reg |= 0x00400000; - mtsdr(SDR0_PE2DLPSET, reg); + mtsdr(SDRN_PESDR_DLPSET(2), reg); out16(FPGA_REG1C,(in16 (FPGA_REG1C) & ~FPGA_REG1C_PE0_ROOTPOINT & ~FPGA_REG1C_PE1_ENDPOINT & ~FPGA_REG1C_PE2_ENDPOINT)); -#if defined(CONFIG_STRESS) - /* - * all this setting done by linux only needed by stress an charac. test - * procedure - * PCIe 1 Rootpoint PCIe2 Endpoint - * PCIe 0 FIR Pre-emphasis Filter Coefficients & Transmit Driver - * Power Level - */ - for (i = 0, disp = 0; i < 8; i++, disp += 3) { - mfsdr(SDR0_PE0HSSSET1L0 + disp, reg); - reg |= 0x33000000; - mtsdr(SDR0_PE0HSSSET1L0 + disp, reg); - } - - /* - * PCIe 1 FIR Pre-emphasis Filter Coefficients & Transmit Driver - * Power Level - */ - for (i = 0, disp = 0; i < 4; i++, disp += 3) { - mfsdr(SDR0_PE1HSSSET1L0 + disp, reg); - reg |= 0x33000000; - mtsdr(SDR0_PE1HSSSET1L0 + disp, reg); - } - - /* - * PCIE 2 FIR Pre-emphasis Filter Coefficients & Transmit Driver - * Power Level - */ - for (i = 0, disp = 0; i < 4; i++, disp += 3) { - mfsdr(SDR0_PE2HSSSET1L0 + disp, reg); - reg |= 0x33000000; - mtsdr(SDR0_PE2HSSSET1L0 + disp, reg); - } - - reg = 0x21242222; - mtsdr(SDR0_PE2UTLSET1, reg); - reg = 0x11000000; - mtsdr(SDR0_PE2UTLSET2, reg); - /* pci express 1 Endpoint Mode */ - reg = 0x00004000; - mtsdr(SDR0_PE2DLPSET, reg); - - mtsdr(SDR0_UART1, 0x2080005a); /* patch for TG */ -#endif return 0; } diff --git a/board/korat/korat.c b/board/korat/korat.c index 51874ea..0d90fb3 100644 --- a/board/korat/korat.c +++ b/board/korat/korat.c @@ -33,7 +33,7 @@ #include <asm/bitops.h> #include <asm/gpio.h> #include <asm/io.h> -#include <asm/ppc4xx-intvec.h> +#include <asm/ppc4xx-uic.h> #include <asm/processor.h> DECLARE_GLOBAL_DATA_PTR; @@ -575,7 +575,7 @@ int checkboard(void) */ void korat_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev) { - pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIR2); + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2); } #endif diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c index 131a62d..cc491d0 100644 --- a/board/prodrive/alpr/alpr.c +++ b/board/prodrive/alpr/alpr.c @@ -48,36 +48,48 @@ int board_early_init_f (void) /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - mtdcr (uic0er, 0x00000000); /* disable all */ - mtdcr (uic0cr, 0x00000009); /* SMI & UIC1 crit are critical */ - mtdcr (uic0pr, 0xfffffe03); /* per manual */ - mtdcr (uic0tr, 0x01c00000); /* per manual */ - mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - + /* + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic1er, 0x00000000); /* disable all */ - mtdcr (uic1cr, 0x00000000); /* all non-critical */ - mtdcr (uic1pr, 0xffffe0ff); /* per ref-board manual */ - mtdcr (uic1tr, 0x00ffc000); /* per ref-board manual */ + mtdcr (uic1cr, 0x00000009); /* SMI & UIC1 crit are critical */ + mtdcr (uic1pr, 0xfffffe03); /* per manual */ + mtdcr (uic1tr, 0x01c00000); /* per manual */ mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uic2er, 0x00000000); /* disable all */ mtdcr (uic2cr, 0x00000000); /* all non-critical */ - mtdcr (uic2pr, 0xffffffff); /* per ref-board manual */ - mtdcr (uic2tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic2pr, 0xffffe0ff); /* per ref-board manual */ + mtdcr (uic2tr, 0x00ffc000); /* per ref-board manual */ mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic2sr, 0xffffffff); /* clear all */ - mtdcr (uicb0sr, 0xfc000000); /* clear all */ - mtdcr (uicb0er, 0x00000000); /* disable all */ - mtdcr (uicb0cr, 0x00000000); /* all non-critical */ - mtdcr (uicb0pr, 0xfc000000); /* */ - mtdcr (uicb0tr, 0x00000000); /* */ - mtdcr (uicb0vr, 0x00000001); /* */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + mtdcr (uic3er, 0x00000000); /* disable all */ + mtdcr (uic3cr, 0x00000000); /* all non-critical */ + mtdcr (uic3pr, 0xffffffff); /* per ref-board manual */ + mtdcr (uic3tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic3vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + + mtdcr (uic0sr, 0xfc000000); /* clear all */ + mtdcr (uic0er, 0x00000000); /* disable all */ + mtdcr (uic0cr, 0x00000000); /* all non-critical */ + mtdcr (uic0pr, 0xfc000000); /* */ + mtdcr (uic0tr, 0x00000000); /* */ + mtdcr (uic0vr, 0x00000001); /* */ /* Setup shutdown/SSD empty interrupt as inputs */ out32(GPIO0_TCR, in32(GPIO0_TCR) & ~(CFG_GPIO_SHUTDOWN | CFG_GPIO_SSD_EMPTY)); diff --git a/board/sandburst/karef/karef.c b/board/sandburst/karef/karef.c index 2d71d3b..72ce976 100644 --- a/board/sandburst/karef/karef.c +++ b/board/sandburst/karef/karef.c @@ -195,36 +195,48 @@ int board_early_init_f (void) /*--------------------------------------------------------------------+ * Setup the interrupt controller polarities, triggers, etc. +-------------------------------------------------------------------*/ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - mtdcr (uic0er, 0x00000000); /* disable all */ - mtdcr (uic0cr, 0x00000000); /* all non- critical */ - mtdcr (uic0pr, 0xfffffe03); /* polarity */ - mtdcr (uic0tr, 0x01c00000); /* trigger edge vs level */ - mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - + /* + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic1er, 0x00000000); /* disable all */ - mtdcr (uic1cr, 0x00000000); /* all non-critical */ - mtdcr (uic1pr, 0xffffc8ff); /* polarity */ - mtdcr (uic1tr, 0x00ff0000); /* trigger edge vs level */ + mtdcr (uic1cr, 0x00000000); /* all non- critical */ + mtdcr (uic1pr, 0xfffffe03); /* polarity */ + mtdcr (uic1tr, 0x01c00000); /* trigger edge vs level */ mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uic2er, 0x00000000); /* disable all */ mtdcr (uic2cr, 0x00000000); /* all non-critical */ - mtdcr (uic2pr, 0xffff83ff); /* polarity */ - mtdcr (uic2tr, 0x00ff8c0f); /* trigger edge vs level */ + mtdcr (uic2pr, 0xffffc8ff); /* polarity */ + mtdcr (uic2tr, 0x00ff0000); /* trigger edge vs level */ mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic2sr, 0xffffffff); /* clear all */ - mtdcr (uicb0sr, 0xfc000000); /* clear all */ - mtdcr (uicb0er, 0x00000000); /* disable all */ - mtdcr (uicb0cr, 0x00000000); /* all non-critical */ - mtdcr (uicb0pr, 0xfc000000); - mtdcr (uicb0tr, 0x00000000); - mtdcr (uicb0vr, 0x00000001); + mtdcr (uic3sr, 0xffffffff); /* clear all */ + mtdcr (uic3er, 0x00000000); /* disable all */ + mtdcr (uic3cr, 0x00000000); /* all non-critical */ + mtdcr (uic3pr, 0xffff83ff); /* polarity */ + mtdcr (uic3tr, 0x00ff8c0f); /* trigger edge vs level */ + mtdcr (uic3vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + + mtdcr (uic0sr, 0xfc000000); /* clear all */ + mtdcr (uic0er, 0x00000000); /* disable all */ + mtdcr (uic0cr, 0x00000000); /* all non-critical */ + mtdcr (uic0pr, 0xfc000000); + mtdcr (uic0tr, 0x00000000); + mtdcr (uic0vr, 0x00000001); fpga_init(); diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c index 66cdfb1..c38850d 100644 --- a/board/sandburst/metrobox/metrobox.c +++ b/board/sandburst/metrobox/metrobox.c @@ -185,36 +185,48 @@ int board_early_init_f (void) /*--------------------------------------------------------------------+ * Setup the interrupt controller polarities, triggers, etc. +-------------------------------------------------------------------*/ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - mtdcr (uic0er, 0x00000000); /* disable all */ - mtdcr (uic0cr, 0x00000000); /* all non- critical */ - mtdcr (uic0pr, 0xfffffe03); /* polarity */ - mtdcr (uic0tr, 0x01c00000); /* trigger edge vs level */ - mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - + /* + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic1er, 0x00000000); /* disable all */ - mtdcr (uic1cr, 0x00000000); /* all non-critical */ - mtdcr (uic1pr, 0xffffc8ff); /* polarity */ - mtdcr (uic1tr, 0x00ff0000); /* trigger edge vs level */ + mtdcr (uic1cr, 0x00000000); /* all non- critical */ + mtdcr (uic1pr, 0xfffffe03); /* polarity */ + mtdcr (uic1tr, 0x01c00000); /* trigger edge vs level */ mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uic2er, 0x00000000); /* disable all */ mtdcr (uic2cr, 0x00000000); /* all non-critical */ - mtdcr (uic2pr, 0xffff83ff); /* polarity */ - mtdcr (uic2tr, 0x00ff8c0f); /* trigger edge vs level */ + mtdcr (uic2pr, 0xffffc8ff); /* polarity */ + mtdcr (uic2tr, 0x00ff0000); /* trigger edge vs level */ mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic2sr, 0xffffffff); /* clear all */ - mtdcr (uicb0sr, 0xfc000000); /* clear all */ - mtdcr (uicb0er, 0x00000000); /* disable all */ - mtdcr (uicb0cr, 0x00000000); /* all non-critical */ - mtdcr (uicb0pr, 0xfc000000); - mtdcr (uicb0tr, 0x00000000); - mtdcr (uicb0vr, 0x00000001); + mtdcr (uic3sr, 0xffffffff); /* clear all */ + mtdcr (uic3er, 0x00000000); /* disable all */ + mtdcr (uic3cr, 0x00000000); /* all non-critical */ + mtdcr (uic3pr, 0xffff83ff); /* polarity */ + mtdcr (uic3tr, 0x00ff8c0f); /* trigger edge vs level */ + mtdcr (uic3vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + + mtdcr (uic0sr, 0xfc000000); /* clear all */ + mtdcr (uic0er, 0x00000000); /* disable all */ + mtdcr (uic0cr, 0x00000000); /* all non-critical */ + mtdcr (uic0pr, 0xfc000000); + mtdcr (uic0tr, 0x00000000); + mtdcr (uic0vr, 0x00000001); fpga_init(); diff --git a/board/xpedite1k/xpedite1k.c b/board/xpedite1k/xpedite1k.c index bc7e3bd..c94a345 100644 --- a/board/xpedite1k/xpedite1k.c +++ b/board/xpedite1k/xpedite1k.c @@ -59,36 +59,48 @@ int board_early_init_f(void) /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - mtdcr (uic0er, 0x00000000); /* disable all */ - mtdcr (uic0cr, 0x00000003); /* SMI & UIC1 crit are critical */ - mtdcr (uic0pr, 0xfffffe00); /* per ref-board manual */ - mtdcr (uic0tr, 0x01c00000); /* per ref-board manual */ - mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */ - mtdcr (uic0sr, 0xffffffff); /* clear all */ - + /* + * Because of the interrupt handling rework to handle 440GX interrupts + * with the common code, we needed to change names of the UIC registers. + * Here the new relationship: + * + * U-Boot name 440GX name + * ----------------------- + * UIC0 UICB0 + * UIC1 UIC0 + * UIC2 UIC1 + * UIC3 UIC2 + */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic1er, 0x00000000); /* disable all */ - mtdcr (uic1cr, 0x00000000); /* all non-critical */ - mtdcr (uic1pr, 0xffffc0ff); /* per ref-board manual */ - mtdcr (uic1tr, 0x00ff8000); /* per ref-board manual */ + mtdcr (uic1cr, 0x00000003); /* SMI & UIC1 crit are critical */ + mtdcr (uic1pr, 0xfffffe00); /* per ref-board manual */ + mtdcr (uic1tr, 0x01c00000); /* per ref-board manual */ mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic1sr, 0xffffffff); /* clear all */ mtdcr (uic2sr, 0xffffffff); /* clear all */ mtdcr (uic2er, 0x00000000); /* disable all */ mtdcr (uic2cr, 0x00000000); /* all non-critical */ - mtdcr (uic2pr, 0xffffffff); /* per ref-board manual */ - mtdcr (uic2tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic2pr, 0xffffc0ff); /* per ref-board manual */ + mtdcr (uic2tr, 0x00ff8000); /* per ref-board manual */ mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */ mtdcr (uic2sr, 0xffffffff); /* clear all */ - mtdcr (uicb0sr, 0xfc000000); /* clear all */ - mtdcr (uicb0er, 0x00000000); /* disable all */ - mtdcr (uicb0cr, 0x00000000); /* all non-critical */ - mtdcr (uicb0pr, 0xfc000000); /* */ - mtdcr (uicb0tr, 0x00000000); /* */ - mtdcr (uicb0vr, 0x00000001); /* */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + mtdcr (uic3er, 0x00000000); /* disable all */ + mtdcr (uic3cr, 0x00000000); /* all non-critical */ + mtdcr (uic3pr, 0xffffffff); /* per ref-board manual */ + mtdcr (uic3tr, 0x00ff8c0f); /* per ref-board manual */ + mtdcr (uic3vr, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr (uic3sr, 0xffffffff); /* clear all */ + + mtdcr (uic0sr, 0xfc000000); /* clear all */ + mtdcr (uic0er, 0x00000000); /* disable all */ + mtdcr (uic0cr, 0x00000000); /* all non-critical */ + mtdcr (uic0pr, 0xfc000000); /* */ + mtdcr (uic0tr, 0x00000000); /* */ + mtdcr (uic0vr, 0x00000001); /* */ LED0_ON(); diff --git a/common/cmd_reginfo.c b/common/cmd_reginfo.c index 0657e4b..c0a1459 100644 --- a/common/cmd_reginfo.c +++ b/common/cmd_reginfo.c @@ -93,11 +93,10 @@ int do_reginfo (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) #elif defined (CONFIG_405GP) printf ("\n405GP registers; MSR=%08x\n",mfmsr()); printf ("\nUniversal Interrupt Controller Regs\n" - "uicsr uicsrs uicer uiccr uicpr uictr uicmsr uicvr uicvcr" + "uicsr uicer uiccr uicpr uictr uicmsr uicvr uicvcr" "\n" - "%08x %08x %08x %08x %08x %08x %08x %08x %08x\n", + "%08x %08x %08x %08x %08x %08x %08x %08x\n", mfdcr(uicsr), - mfdcr(uicsrs), mfdcr(uicer), mfdcr(uiccr), mfdcr(uicpr), diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index a27e276..ec1765e 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -50,9 +50,19 @@ #include "ecc.h" -#if defined(CONFIG_SPD_EEPROM) && \ - (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT)) +#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) + +#define PPC4xx_IBM_DDR2_DUMP_REGISTER(mnemonic) \ + do { \ + u32 data; \ + mfsdram(SDRAM_##mnemonic, data); \ + printf("%20s[%02x] = 0x%08X\n", \ + "SDRAM_" #mnemonic, SDRAM_##mnemonic, data); \ + } while (0) + +static inline void ppc4xx_ibm_ddr2_register_dump(void); + +#if defined(CONFIG_SPD_EEPROM) /*-----------------------------------------------------------------------------+ * Defines @@ -257,7 +267,6 @@ static void test(void); #else static void DQS_calibration_process(void); #endif -static void ppc440sp_sdram_register_dump(void); int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); void dcbz_area(u32 start_address, u32 num_bytes); @@ -607,7 +616,7 @@ phys_size_t initdram(int board_type) remove_tlb(0, dram_size); program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE); - ppc440sp_sdram_register_dump(); + ppc4xx_ibm_ddr2_register_dump(); /* * Clear potential errors resulting from auto-calibration. @@ -2760,7 +2769,7 @@ calibration_loop: printf("\nERROR: Cannot determine a common read delay for the " "DIMM(s) installed.\n"); debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__); - ppc440sp_sdram_register_dump(); + ppc4xx_ibm_ddr2_register_dump(); spd_ddr_init_hang (); } @@ -2946,169 +2955,8 @@ static void test(void) } #endif -#if defined(DEBUG) -static void ppc440sp_sdram_register_dump(void) -{ - unsigned int sdram_reg; - unsigned int sdram_data; - unsigned int dcr_data; - - printf("\n Register Dump:\n"); - sdram_reg = SDRAM_MCSTAT; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MCSTAT = 0x%08X", sdram_data); - sdram_reg = SDRAM_MCOPT1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MCOPT1 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MCOPT2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MCOPT2 = 0x%08X", sdram_data); - sdram_reg = SDRAM_MODT0; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT0 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MODT1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT1 = 0x%08X", sdram_data); - sdram_reg = SDRAM_MODT2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT2 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MODT3; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT3 = 0x%08X", sdram_data); - sdram_reg = SDRAM_CODT; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_CODT = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_VVPR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_VVPR = 0x%08X", sdram_data); - sdram_reg = SDRAM_OPARS; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_OPARS = 0x%08X\n", sdram_data); - /* - * OPAR2 is only used as a trigger register. - * No data is contained in this register, and reading or writing - * to is can cause bad things to happen (hangs). Just skip it - * and report NA - * sdram_reg = SDRAM_OPAR2; - * mfsdram(sdram_reg, sdram_data); - * printf(" SDRAM_OPAR2 = 0x%08X\n", sdram_data); - */ - printf(" SDRAM_OPART = N/A "); - sdram_reg = SDRAM_RTR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RTR = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MB0CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB0CF = 0x%08X", sdram_data); - sdram_reg = SDRAM_MB1CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB1CF = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MB2CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB2CF = 0x%08X", sdram_data); - sdram_reg = SDRAM_MB3CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB3CF = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR0; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR0 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR1 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR2 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR3; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR3 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR4; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR4 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR5; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR5 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR6; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR6 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR7; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR7 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR8; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR8 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR9; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR9 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR10; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR10 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR11; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR11 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR12; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR12 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR13; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR13 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR14; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR14 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR15; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR15 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_RQDC; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RQDC = 0x%08X", sdram_data); - sdram_reg = SDRAM_RFDC; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RFDC = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_RDCC; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RDCC = 0x%08X", sdram_data); - sdram_reg = SDRAM_DLCR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_DLCR = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_CLKTR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_CLKTR = 0x%08X", sdram_data); - sdram_reg = SDRAM_WRDTR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_WRDTR = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_SDTR1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_SDTR1 = 0x%08X", sdram_data); - sdram_reg = SDRAM_SDTR2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_SDTR2 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_SDTR3; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_SDTR3 = 0x%08X", sdram_data); - sdram_reg = SDRAM_MMODE; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MMODE = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MEMODE; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MEMODE = 0x%08X", sdram_data); - sdram_reg = SDRAM_ECCCR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_ECCCR = 0x%08X\n\n", sdram_data); - - dcr_data = mfdcr(SDRAM_R0BAS); - printf(" MQ0_B0BAS = 0x%08X", dcr_data); - dcr_data = mfdcr(SDRAM_R1BAS); - printf(" MQ1_B0BAS = 0x%08X\n", dcr_data); - dcr_data = mfdcr(SDRAM_R2BAS); - printf(" MQ2_B0BAS = 0x%08X", dcr_data); - dcr_data = mfdcr(SDRAM_R3BAS); - printf(" MQ3_B0BAS = 0x%08X\n", dcr_data); -} -#else /* !defined(DEBUG) */ -static void ppc440sp_sdram_register_dump(void) -{ -} -#endif /* defined(DEBUG) */ -#elif defined(CONFIG_405EX) +#else /* CONFIG_SPD_EEPROM */ + /*----------------------------------------------------------------------------- * Function: initdram * Description: Configures the PPC405EX(r) DDR1/DDR2 SDRAM memory @@ -3222,8 +3070,96 @@ phys_size_t initdram(int board_type) #if defined(CONFIG_DDR_ECC) ecc_init(CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20); #endif /* defined(CONFIG_DDR_ECC) */ + + ppc4xx_ibm_ddr2_register_dump(); #endif /* !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ return (CFG_MBYTES_SDRAM << 20); } -#endif /* defined(CONFIG_SPD_EEPROM) && defined(CONFIG_440SP) || ... */ +#endif /* CONFIG_SPD_EEPROM */ + +static inline void ppc4xx_ibm_ddr2_register_dump(void) +{ +#if defined(DEBUG) + printf("\nPPC4xx IBM DDR2 Register Dump:\n"); + +#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT)) + PPC4xx_IBM_DDR2_DUMP_REGISTER(R0BAS); + PPC4xx_IBM_DDR2_DUMP_REGISTER(R1BAS); + PPC4xx_IBM_DDR2_DUMP_REGISTER(R2BAS); + PPC4xx_IBM_DDR2_DUMP_REGISTER(R3BAS); +#endif /* (defined(CONFIG_440SP) || ... */ +#if defined(CONFIG_405EX) + PPC4xx_IBM_DDR2_DUMP_REGISTER(BESR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(BEARL); + PPC4xx_IBM_DDR2_DUMP_REGISTER(BEARH); + PPC4xx_IBM_DDR2_DUMP_REGISTER(WMIRQ); + PPC4xx_IBM_DDR2_DUMP_REGISTER(PLBOPT); + PPC4xx_IBM_DDR2_DUMP_REGISTER(PUABA); +#endif /* defined(CONFIG_405EX) */ + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB0CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB1CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB2CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB3CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MCSTAT); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MCOPT1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MCOPT2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT0); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT3); + PPC4xx_IBM_DDR2_DUMP_REGISTER(CODT); +#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT)) + PPC4xx_IBM_DDR2_DUMP_REGISTER(VVPR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(OPARS); + /* + * OPART is only used as a trigger register. + * + * No data is contained in this register, and reading or writing + * to is can cause bad things to happen (hangs). Just skip it and + * report "N/A". + */ + printf("%20s = N/A\n", "SDRAM_OPART"); +#endif /* defined(CONFIG_440SP) || ... */ + PPC4xx_IBM_DDR2_DUMP_REGISTER(RTR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR0); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR3); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR4); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR5); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR6); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR7); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR8); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR9); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR10); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR11); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR12); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR13); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR14); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR15); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RQDC); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RFDC); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RDCC); + PPC4xx_IBM_DDR2_DUMP_REGISTER(DLCR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(CLKTR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(WRDTR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR3); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MMODE); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MEMODE); + PPC4xx_IBM_DDR2_DUMP_REGISTER(ECCCR); +#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT)) + PPC4xx_IBM_DDR2_DUMP_REGISTER(CID); +#endif /* defined(CONFIG_440SP) || ... */ + PPC4xx_IBM_DDR2_DUMP_REGISTER(RID); + PPC4xx_IBM_DDR2_DUMP_REGISTER(FCSR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RTSR); +#endif /* defined(DEBUG) */ +} + +#endif /* CONFIG_SDRAM_PPC4xx_IBM_DDR2 */ diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 4e863dc..8a38335 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -90,7 +90,6 @@ #include <405_mal.h> #include <miiphy.h> #include <malloc.h> -#include <asm/ppc4xx-intvec.h> /* * Only compile for platform with AMCC EMAC ethernet controller and @@ -122,11 +121,65 @@ * Defines for MAL/EMAC interrupt conditions as reported in the UIC (Universal * Interrupt Controller). *-----------------------------------------------------------------------------*/ -#define MAL_UIC_ERR ( UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE) -#define MAL_UIC_DEF (UIC_MAL_RXEOB | MAL_UIC_ERR) -#define EMAC_UIC_DEF UIC_ENET -#define EMAC_UIC_DEF1 UIC_ENET1 -#define SEL_UIC_DEF(p) (p ? UIC_ENET1 : UIC_ENET ) +#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev) * VECNUM_ETH1_OFFS)) + +#if defined(CONFIG_HAS_ETH3) +#if !defined(CONFIG_440GX) +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1)) || \ + UIC_MASK(ETH_IRQ_NUM(2)) || UIC_MASK(ETH_IRQ_NUM(3))) +#else +/* Unfortunately 440GX spreads EMAC interrupts on multiple UIC's */ +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1))) +#define UIC_ETHxB (UIC_MASK(ETH_IRQ_NUM(2)) || UIC_MASK(ETH_IRQ_NUM(3))) +#endif /* !defined(CONFIG_440GX) */ +#elif defined(CONFIG_HAS_ETH2) +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1)) || \ + UIC_MASK(ETH_IRQ_NUM(2))) +#elif defined(CONFIG_HAS_ETH1) +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1))) +#else +#define UIC_ETHx UIC_MASK(ETH_IRQ_NUM(0)) +#endif + +/* + * Define a default version for UIC_ETHxB for non 440GX so that we can + * use common code for all 4xx variants + */ +#if !defined(UIC_ETHxB) +#define UIC_ETHxB 0 +#endif + +#define UIC_MAL_SERR UIC_MASK(VECNUM_MAL_SERR) +#define UIC_MAL_TXDE UIC_MASK(VECNUM_MAL_TXDE) +#define UIC_MAL_RXDE UIC_MASK(VECNUM_MAL_RXDE) +#define UIC_MAL_TXEOB UIC_MASK(VECNUM_MAL_TXEOB) +#define UIC_MAL_RXEOB UIC_MASK(VECNUM_MAL_RXEOB) + +#define MAL_UIC_ERR (UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE) +#define MAL_UIC_DEF (UIC_MAL_RXEOB | MAL_UIC_ERR) + +/* + * We have 3 different interrupt types: + * - MAL interrupts indicating successful transfer + * - MAL error interrupts indicating MAL related errors + * - EMAC interrupts indicating EMAC related errors + * + * All those interrupts can be on different UIC's, but since + * now at least all interrupts from one type are on the same + * UIC. Only exception is 440GX where the EMAC interrupts are + * spread over two UIC's! + */ +#if defined(CONFIG_440GX) +#define UIC_BASE_MAL UIC1_DCR_BASE +#define UIC_BASE_MAL_ERR UIC2_DCR_BASE +#define UIC_BASE_EMAC UIC2_DCR_BASE +#define UIC_BASE_EMAC_B UIC3_DCR_BASE +#else +#define UIC_BASE_MAL (UIC0_DCR_BASE + (UIC_NR(VECNUM_MAL_TXEOB) * 0x10)) +#define UIC_BASE_MAL_ERR (UIC0_DCR_BASE + (UIC_NR(VECNUM_MAL_SERR) * 0x10)) +#define UIC_BASE_EMAC (UIC0_DCR_BASE + (UIC_NR(ETH_IRQ_NUM(0)) * 0x10)) +#define UIC_BASE_EMAC_B (UIC0_DCR_BASE + (UIC_NR(ETH_IRQ_NUM(0)) * 0x10)) +#endif #undef INFO_4XX_ENET @@ -166,9 +219,6 @@ /*-----------------------------------------------------------------------------+ * Global variables. TX and RX descriptors and buffers. *-----------------------------------------------------------------------------*/ -/* IER globals */ -static uint32_t mal_ier; - #if !defined(CONFIG_NET_MULTI) struct eth_device *emac0_dev = NULL; #endif @@ -200,12 +250,6 @@ struct eth_device *emac0_dev = NULL; #define CONFIG_EMAC_NR_START 0 #endif -#if defined(CONFIG_405EX) || defined(CONFIG_440EPX) -#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev))) -#else -#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev) * 2)) -#endif - #define MAL_RX_DESC_SIZE 2048 #define MAL_TX_DESC_SIZE 2048 #define MAL_ALLOC_SIZE (MAL_TX_DESC_SIZE + MAL_RX_DESC_SIZE) @@ -465,30 +509,88 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) #if defined(CONFIG_405EX) int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) { - u32 gmiifer = 0; + u32 rgmiifer = 0; /* - * Right now only 2*RGMII is supported. Please extend when needed. - * sr - 2007-09-19 + * The 405EX(r)'s RGMII bridge can operate in one of several + * modes, only one of which (2 x RGMII) allows the + * simultaneous use of both EMACs on the 405EX. */ - switch (1) { - case 1: + + switch (CONFIG_EMAC_PHY_MODE) { + + case EMAC_PHY_MODE_NONE: + /* No ports */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_NONE_RGMII: + /* 1 x RGMII port on channel 0 */ + rgmiifer |= RGMII_FER_RGMII << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_RGMII; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_RGMII_NONE: + /* 1 x RGMII port on channel 1 */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_RGMII << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_RGMII; + break; + case EMAC_PHY_MODE_RGMII_RGMII: /* 2 x RGMII ports */ - out_be32((void *)RGMII_FER, 0x00000055); + rgmiifer |= RGMII_FER_RGMII << 0; + rgmiifer |= RGMII_FER_RGMII << 4; + out_be32((void *)RGMII_FER, rgmiifer); bis->bi_phymode[0] = BI_PHYMODE_RGMII; bis->bi_phymode[1] = BI_PHYMODE_RGMII; break; - case 2: - /* 2 x SMII ports */ + case EMAC_PHY_MODE_NONE_GMII: + /* 1 x GMII port on channel 0 */ + rgmiifer |= RGMII_FER_GMII << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_GMII; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_NONE_MII: + /* 1 x MII port on channel 0 */ + rgmiifer |= RGMII_FER_MII << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_MII; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_GMII_NONE: + /* 1 x GMII port on channel 1 */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_GMII << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_GMII; + break; + case EMAC_PHY_MODE_MII_NONE: + /* 1 x MII port on channel 1 */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_MII << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_MII; break; default: break; } /* Ensure we setup mdio for this devnum and ONLY this devnum */ - gmiifer = in_be32((void *)RGMII_FER); - gmiifer |= (1 << (19-devnum)); - out_be32((void *)RGMII_FER, gmiifer); + rgmiifer = in_be32((void *)RGMII_FER); + rgmiifer |= (1 << (19-devnum)); + out_be32((void *)RGMII_FER, rgmiifer); return ((int)0x0); } @@ -1377,59 +1479,17 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr, } } - -#if defined (CONFIG_440) || defined(CONFIG_405EX) - -#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) -/* - * Hack: On 440SP all enet irq sources are located on UIC1 - * Needs some cleanup. --sr - */ -#define UIC0MSR uic1msr -#define UIC0SR uic1sr -#define UIC1MSR uic1msr -#define UIC1SR uic1sr -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) -/* - * Hack: On 460EX/GT all enet irq sources are located on UIC2 - * Needs some cleanup. --ag - */ -#define UIC0MSR uic2msr -#define UIC0SR uic2sr -#define UIC1MSR uic2msr -#define UIC1SR uic2sr -#else -#define UIC0MSR uic0msr -#define UIC0SR uic0sr -#define UIC1MSR uic1msr -#define UIC1SR uic1sr -#endif - -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_405EX) -#define UICMSR_ETHX uic0msr -#define UICSR_ETHX uic0sr -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) -#define UICMSR_ETHX uic2msr -#define UICSR_ETHX uic2sr -#else -#define UICMSR_ETHX uic1msr -#define UICSR_ETHX uic1sr -#endif - int enetInt (struct eth_device *dev) { int serviced; int rc = -1; /* default to not us */ - unsigned long mal_isr; - unsigned long emac_isr = 0; - unsigned long mal_rx_eob; - unsigned long my_uic0msr, my_uic1msr; - unsigned long my_uicmsr_ethx; - -#if defined(CONFIG_440GX) - unsigned long my_uic2msr; -#endif + u32 mal_isr; + u32 emac_isr = 0; + u32 mal_eob; + u32 uic_mal; + u32 uic_mal_err; + u32 uic_emac; + u32 uic_emac_b; EMAC_4XX_HW_PST hw_p; /* @@ -1448,256 +1508,79 @@ int enetInt (struct eth_device *dev) do { serviced = 0; - my_uic0msr = mfdcr (UIC0MSR); - my_uic1msr = mfdcr (UIC1MSR); -#if defined(CONFIG_440GX) - my_uic2msr = mfdcr (uic2msr); -#endif - my_uicmsr_ethx = mfdcr (UICMSR_ETHX); + uic_mal = mfdcr(UIC_BASE_MAL + UIC_MSR); + uic_mal_err = mfdcr(UIC_BASE_MAL_ERR + UIC_MSR); + uic_emac = mfdcr(UIC_BASE_EMAC + UIC_MSR); + uic_emac_b = mfdcr(UIC_BASE_EMAC_B + UIC_MSR); - if (!(my_uic0msr & (UIC_MRE | UIC_MTE)) - && !(my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE)) - && !(my_uicmsr_ethx & (UIC_ETH0 | UIC_ETH1))) { - /* not for us */ - return (rc); - } -#if defined (CONFIG_440GX) - if (!(my_uic0msr & (UIC_MRE | UIC_MTE)) - && !(my_uic2msr & (UIC_ETH2 | UIC_ETH3))) { + if (!(uic_mal & (UIC_MAL_RXEOB | UIC_MAL_TXEOB)) + && !(uic_mal_err & (UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE)) + && !(uic_emac & UIC_ETHx) && !(uic_emac_b & UIC_ETHxB)) { /* not for us */ return (rc); } -#endif + /* get and clear controller status interrupts */ - /* look at Mal and EMAC interrupts */ - if ((my_uic0msr & (UIC_MRE | UIC_MTE)) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - /* we have a MAL interrupt */ - mal_isr = mfdcr (malesr); - /* look for mal error */ - if (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE)) { - mal_err (dev, mal_isr, my_uic1msr, MAL_UIC_DEF, MAL_UIC_ERR); - serviced = 1; - rc = 0; - } - } + /* look at MAL and EMAC error interrupts */ + if (uic_mal_err & (UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE)) { + /* we have a MAL error interrupt */ + mal_isr = mfdcr(malesr); + mal_err(dev, mal_isr, uic_mal_err, + MAL_UIC_DEF, MAL_UIC_ERR); - /* port by port dispatch of emac interrupts */ - if (hw_p->devnum == 0) { - if (UIC_ETH0 & my_uicmsr_ethx) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (UICSR_ETHX, UIC_ETH0); /* Clear */ - return (rc); /* we had errors so get out */ - } - } + /* clear MAL error interrupt status bits */ + mtdcr(UIC_BASE_MAL_ERR + UIC_SR, + UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE); -#if !defined(CONFIG_440SP) - if (hw_p->devnum == 1) { - if (UIC_ETH1 & my_uicmsr_ethx) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (UICSR_ETHX, UIC_ETH1); /* Clear */ - return (rc); /* we had errors so get out */ - } - } -#if defined (CONFIG_440GX) - if (hw_p->devnum == 2) { - if (UIC_ETH2 & my_uic2msr) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (uic2sr, UIC_ETH2); - return (rc); /* we had errors so get out */ - } + return -1; } - if (hw_p->devnum == 3) { - if (UIC_ETH3 & my_uic2msr) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (uic2sr, UIC_ETH3); - return (rc); /* we had errors so get out */ - } - } -#endif /* CONFIG_440GX */ -#endif /* !CONFIG_440SP */ + /* look for EMAC errors */ + if ((uic_emac & UIC_ETHx) || (uic_emac_b & UIC_ETHxB)) { + emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); + emac_err(dev, emac_isr); - /* handle MAX TX EOB interrupt from a tx */ - if (my_uic0msr & UIC_MTE) { - mal_rx_eob = mfdcr (maltxeobisr); - mtdcr (maltxeobisr, mal_rx_eob); - mtdcr (UIC0SR, UIC_MTE); - } - /* handle MAL RX EOB interupt from a receive */ - /* check for EOB on valid channels */ - if (my_uic0msr & UIC_MRE) { - mal_rx_eob = mfdcr (malrxeobisr); - if ((mal_rx_eob & - (0x80000000 >> (hw_p->devnum * MAL_RX_CHAN_MUL))) - != 0) { /* call emac routine for channel x */ - /* clear EOB - mtdcr(malrxeobisr, mal_rx_eob); */ - enet_rcv (dev, emac_isr); - /* indicate that we serviced an interrupt */ - serviced = 1; - rc = 0; - } - } + /* clear EMAC error interrupt status bits */ + mtdcr(UIC_BASE_EMAC + UIC_SR, UIC_ETHx); + mtdcr(UIC_BASE_EMAC_B + UIC_SR, UIC_ETHxB); - mtdcr (UIC0SR, UIC_MRE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - switch (hw_p->devnum) { - case 0: - mtdcr (UICSR_ETHX, UIC_ETH0); - break; - case 1: - mtdcr (UICSR_ETHX, UIC_ETH1); - break; -#if defined (CONFIG_440GX) - case 2: - mtdcr (uic2sr, UIC_ETH2); - break; - case 3: - mtdcr (uic2sr, UIC_ETH3); - break; -#endif /* CONFIG_440GX */ - default: - break; + return -1; } - } while (serviced); - - return (rc); -} - -#else /* CONFIG_440 */ - -int enetInt (struct eth_device *dev) -{ - int serviced; - int rc = -1; /* default to not us */ - unsigned long mal_isr; - unsigned long emac_isr = 0; - unsigned long mal_rx_eob; - unsigned long my_uicmsr; - - EMAC_4XX_HW_PST hw_p; - - /* - * Because the mal is generic, we need to get the current - * eth device - */ -#if defined(CONFIG_NET_MULTI) - dev = eth_get_dev(); -#else - dev = emac0_dev; -#endif - - hw_p = dev->priv; - - /* enter loop that stays in interrupt code until nothing to service */ - do { - serviced = 0; - my_uicmsr = mfdcr (uicmsr); - - if ((my_uicmsr & (MAL_UIC_DEF | EMAC_UIC_DEF)) == 0) { /* not for us */ - return (rc); - } - /* get and clear controller status interrupts */ - /* look at Mal and EMAC interrupts */ - if ((MAL_UIC_DEF & my_uicmsr) != 0) { /* we have a MAL interrupt */ - mal_isr = mfdcr (malesr); - /* look for mal error */ - if ((my_uicmsr & MAL_UIC_ERR) != 0) { - mal_err (dev, mal_isr, my_uicmsr, MAL_UIC_DEF, MAL_UIC_ERR); - serviced = 1; - rc = 0; - } + /* handle MAX TX EOB interrupt from a tx */ + if (uic_mal & UIC_MAL_TXEOB) { + /* clear MAL interrupt status bits */ + mal_eob = mfdcr(maltxeobisr); + mtdcr(maltxeobisr, mal_eob); + mtdcr(UIC_BASE_MAL + UIC_SR, UIC_MAL_TXEOB); + + /* indicate that we serviced an interrupt */ + serviced = 1; + rc = 0; } - /* port by port dispatch of emac interrupts */ + /* handle MAL RX EOB interupt from a receive */ + /* check for EOB on valid channels */ + if (uic_mal & UIC_MAL_RXEOB) { + mal_eob = mfdcr(malrxeobisr); + if (mal_eob & + (0x80000000 >> (hw_p->devnum * MAL_RX_CHAN_MUL))) { + /* push packet to upper layer */ + enet_rcv(dev, emac_isr); - if ((SEL_UIC_DEF(hw_p->devnum) & my_uicmsr) != 0) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if (((hw_p->emac_ier & emac_isr) != 0) || ((MAL_UIC_ERR & my_uicmsr) != 0)) { - mtdcr (uicsr, MAL_UIC_DEF | SEL_UIC_DEF(hw_p->devnum)); /* Clear */ - return (rc); /* we had errors so get out */ - } + /* clear MAL interrupt status bits */ + mtdcr(UIC_BASE_MAL + UIC_SR, UIC_MAL_RXEOB); - /* handle MAX TX EOB interrupt from a tx */ - if (my_uicmsr & UIC_MAL_TXEOB) { - mal_rx_eob = mfdcr (maltxeobisr); - mtdcr (maltxeobisr, mal_rx_eob); - mtdcr (uicsr, UIC_MAL_TXEOB); - } - /* handle MAL RX EOB interupt from a receive */ - /* check for EOB on valid channels */ - if (my_uicmsr & UIC_MAL_RXEOB) - { - mal_rx_eob = mfdcr (malrxeobisr); - if ((mal_rx_eob & (0x80000000 >> hw_p->devnum)) != 0) { /* call emac routine for channel x */ - /* clear EOB - mtdcr(malrxeobisr, mal_rx_eob); */ - enet_rcv (dev, emac_isr); /* indicate that we serviced an interrupt */ serviced = 1; rc = 0; } } - mtdcr (uicsr, MAL_UIC_DEF|EMAC_UIC_DEF|EMAC_UIC_DEF1); /* Clear */ -#if defined(CONFIG_405EZ) - mtsdr (sdricintstat, SDR_ICRX_STAT | SDR_ICTX0_STAT | SDR_ICTX1_STAT); -#endif /* defined(CONFIG_405EZ) */ - } - while (serviced); + } while (serviced); return (rc); } -#endif /* CONFIG_440 */ - /*-----------------------------------------------------------------------------+ * MAL Error Routine *-----------------------------------------------------------------------------*/ @@ -1883,6 +1766,7 @@ int ppc_4xx_eth_initialize (bd_t * bis) EMAC_4XX_HW_PST hw = NULL; u8 ethaddr[4 + CONFIG_EMAC_NR_START][6]; u32 hw_addr[4]; + u32 mal_ier; #if defined(CONFIG_440GX) unsigned long pfc1; @@ -2020,19 +1904,19 @@ int ppc_4xx_eth_initialize (bd_t * bis) mtdcr (malier, mal_ier); /* install MAL interrupt handler */ - irq_install_handler (VECNUM_MS, + irq_install_handler (VECNUM_MAL_SERR, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_MTE, + irq_install_handler (VECNUM_MAL_TXEOB, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_MRE, + irq_install_handler (VECNUM_MAL_RXEOB, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_TXDE, + irq_install_handler (VECNUM_MAL_TXDE, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_RXDE, + irq_install_handler (VECNUM_MAL_RXDE, (interrupt_handler_t *) enetInt, dev); virgin = 1; diff --git a/cpu/ppc4xx/4xx_uart.c b/cpu/ppc4xx/4xx_uart.c index a7587d4..766e586 100644 --- a/cpu/ppc4xx/4xx_uart.c +++ b/cpu/ppc4xx/4xx_uart.c @@ -46,7 +46,7 @@ #include <asm/processor.h> #include <asm/io.h> #include <watchdog.h> -#include <asm/ppc4xx-intvec.h> +#include <ppc4xx.h> #ifdef CONFIG_SERIAL_MULTI #include <serial.h> diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c index 39f439d..ef32bc6 100644 --- a/cpu/ppc4xx/cpu.c +++ b/cpu/ppc4xx/cpu.c @@ -184,6 +184,19 @@ static char *bootstrap_str[] = { static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'G', 'F', 'H' }; #endif +#if defined(CONFIG_460SX) +#define SDR0_PINSTP_SHIFT 29 +static char *bootstrap_str[] = { + "EBC (8 bits)", + "EBC (16 bits)", + "EBC (32 bits)", + "NAND (8 bits)", + "I2C (Addr 0x54)", /* A8 */ + "I2C (Addr 0x52)", /* A4 */ +}; +static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'G' }; +#endif + #if defined(CONFIG_405EZ) #define SDR0_PINSTP_SHIFT 28 static char *bootstrap_str[] = { @@ -509,6 +522,26 @@ int checkcpu (void) strcpy(addstr, "Security/Kasumi support"); break; + case PVR_460SX_RA: + puts("SX Rev. A"); + strcpy(addstr, "Security support"); + break; + + case PVR_460SX_RA_V1: + puts("SX Rev. A"); + strcpy(addstr, "No Security support"); + break; + + case PVR_460GX_RA: + puts("GX Rev. A"); + strcpy(addstr, "Security support"); + break; + + case PVR_460GX_RA_V1: + puts("GX Rev. A"); + strcpy(addstr, "No Security support"); + break; + default: printf (" UNKNOWN (PVR=%08x)", pvr); break; diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c index ac64279..e2d0402 100644 --- a/cpu/ppc4xx/cpu_init.c +++ b/cpu/ppc4xx/cpu_init.c @@ -138,9 +138,10 @@ void reconfigure_pll(u32 new_cpu_freq) void cpu_init_f (void) { -#if defined(CONFIG_WATCHDOG) || defined(CONFIG_460EX) +#if defined(CONFIG_WATCHDOG) || defined(CONFIG_440GX) || defined(CONFIG_460EX) u32 val; #endif + reconfigure_pll(CFG_PLL_RECONFIG); #if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && !defined(CFG_4xx_GPIO_TABLE) @@ -273,6 +274,18 @@ cpu_init_f (void) reset_4xx_watchdog(); #endif /* CONFIG_WATCHDOG */ +#if defined(CONFIG_440GX) + /* Take the GX out of compatibility mode + * Travis Sawyer, 9 Mar 2004 + * NOTE: 440gx user manual inconsistency here + * Compatibility mode and Ethernet Clock select are not + * correct in the manual + */ + mfsdr(sdr_mfr, val); + val &= ~0x10000000; + mtsdr(sdr_mfr,val); +#endif /* CONFIG_440GX */ + #if defined(CONFIG_460EX) /* * Set SDR0_AHB_CFG[A2P_INCR4] (bit 24) and diff --git a/cpu/ppc4xx/interrupts.c b/cpu/ppc4xx/interrupts.c index 8620e2b..8215dc6 100644 --- a/cpu/ppc4xx/interrupts.c +++ b/cpu/ppc4xx/interrupts.c @@ -34,27 +34,22 @@ #include <ppc4xx.h> #include <ppc_asm.tmpl> #include <commproc.h> -#include <asm/ppc4xx-intvec.h> -DECLARE_GLOBAL_DATA_PTR; - -/* - * Define the number of UIC's - */ -#if defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) -#define UIC_MAX 4 -#elif defined(CONFIG_440GX) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_405EX) -#define UIC_MAX 3 -#elif defined(CONFIG_440GP) || defined(CONFIG_440SP) || \ - defined(CONFIG_440EP) || defined(CONFIG_440GR) -#define UIC_MAX 2 +#if (UIC_MAX > 3) +#define UICB0_ALL (UIC_MASK(VECNUM_UIC1CI) | UIC_MASK(VECNUM_UIC1NCI) | \ + UIC_MASK(VECNUM_UIC2CI) | UIC_MASK(VECNUM_UIC2NCI) | \ + UIC_MASK(VECNUM_UIC3CI) | UIC_MASK(VECNUM_UIC3NCI)) +#elif (UIC_MAX > 2) +#define UICB0_ALL (UIC_MASK(VECNUM_UIC1CI) | UIC_MASK(VECNUM_UIC1NCI) | \ + UIC_MASK(VECNUM_UIC2CI) | UIC_MASK(VECNUM_UIC2NCI)) +#elif (UIC_MAX > 1) +#define UICB0_ALL (UIC_MASK(VECNUM_UIC1CI) | UIC_MASK(VECNUM_UIC1NCI)) #else -#define UIC_MAX 1 +#define UICB0_ALL 0 #endif +DECLARE_GLOBAL_DATA_PTR; + /* * CPM interrupt vector functions. */ @@ -69,10 +64,6 @@ static struct irq_action irq_vecs[UIC_MAX * 32]; u32 get_dcr(u16); void set_dcr(u16, u32); -#if (UIC_MAX > 1) && !defined(CONFIG_440GX) -static void uic_cascade_interrupt(void *para); -#endif - #if defined(CONFIG_440) /* SPRN changed in 440 */ @@ -156,37 +147,19 @@ int interrupt_init_cpu (unsigned *decrementer_count) */ set_evpr(0x00000000); -#if !defined(CONFIG_440GX) #if (UIC_MAX > 1) /* Install the UIC1 handlers */ - irq_install_handler(VECNUM_UIC1NC, uic_cascade_interrupt, 0); - irq_install_handler(VECNUM_UIC1C, uic_cascade_interrupt, 0); + irq_install_handler(VECNUM_UIC1NCI, (void *)(void *)external_interrupt, 0); + irq_install_handler(VECNUM_UIC1CI, (void *)(void *)external_interrupt, 0); #endif #if (UIC_MAX > 2) - irq_install_handler(VECNUM_UIC2NC, uic_cascade_interrupt, 0); - irq_install_handler(VECNUM_UIC2C, uic_cascade_interrupt, 0); + irq_install_handler(VECNUM_UIC2NCI, (void *)(void *)external_interrupt, 0); + irq_install_handler(VECNUM_UIC2CI, (void *)(void *)external_interrupt, 0); #endif #if (UIC_MAX > 3) - irq_install_handler(VECNUM_UIC3NC, uic_cascade_interrupt, 0); - irq_install_handler(VECNUM_UIC3C, uic_cascade_interrupt, 0); + irq_install_handler(VECNUM_UIC3NCI, (void *)(void *)external_interrupt, 0); + irq_install_handler(VECNUM_UIC3CI, (void *)(void *)external_interrupt, 0); #endif -#else /* !defined(CONFIG_440GX) */ - /* Take the GX out of compatibility mode - * Travis Sawyer, 9 Mar 2004 - * NOTE: 440gx user manual inconsistency here - * Compatibility mode and Ethernet Clock select are not - * correct in the manual - */ - mfsdr(sdr_mfr, val); - val &= ~0x10000000; - mtsdr(sdr_mfr,val); - - /* Enable UIC interrupts via UIC Base Enable Register */ - mtdcr(uicb0sr, UICB0_ALL); - mtdcr(uicb0er, 0x54000000); - /* None are critical */ - mtdcr(uicb0cr, 0); -#endif /* !defined(CONFIG_440GX) */ return (0); } @@ -217,8 +190,7 @@ static void uic_interrupt(u32 uic_base, int vec_base) (*irq_vecs[vec].handler)(irq_vecs[vec].arg); } else { set_dcr(uic_base + UIC_ER, - get_dcr(uic_base + UIC_ER) & - ~(0x80000000 >> (vec & 0x1f))); + get_dcr(uic_base + UIC_ER) & ~UIC_MASK(vec)); printf("Masking bogus interrupt vector %d" " (UIC_BASE=0x%x)\n", vec, uic_base); } @@ -227,7 +199,7 @@ static void uic_interrupt(u32 uic_base, int vec_base) * After servicing the interrupt, we have to remove the * status indicator */ - set_dcr(uic_base + UIC_SR, (0x80000000 >> (vec & 0x1f))); + set_dcr(uic_base + UIC_SR, UIC_MASK(vec)); } /* @@ -238,27 +210,6 @@ static void uic_interrupt(u32 uic_base, int vec_base) } } -#if (UIC_MAX > 1) && !defined(CONFIG_440GX) -static void uic_cascade_interrupt(void *para) -{ - external_interrupt(para); -} -#endif - -#if defined(CONFIG_440) -#if defined(CONFIG_440GX) -/* 440GX uses base uic register */ -#define UIC_BMSR uicb0msr -#define UIC_BSR uicb0sr -#else -#define UIC_BMSR uic0msr -#define UIC_BSR uic0sr -#endif -#else /* CONFIG_440 */ -#define UIC_BMSR uicmsr -#define UIC_BSR uicsr -#endif /* CONFIG_440 */ - /* * Handle external interrupts */ @@ -269,36 +220,30 @@ void external_interrupt(struct pt_regs *regs) /* * Read masked interrupt status register to determine interrupt source */ - uic_msr = mfdcr(UIC_BMSR); + uic_msr = mfdcr(uic0msr); #if (UIC_MAX > 1) - if ((UICB0_UIC1CI & uic_msr) || (UICB0_UIC1NCI & uic_msr)) + if ((UIC_MASK(VECNUM_UIC1CI) & uic_msr) || + (UIC_MASK(VECNUM_UIC1NCI) & uic_msr)) uic_interrupt(UIC1_DCR_BASE, 32); #endif #if (UIC_MAX > 2) - if ((UICB0_UIC2CI & uic_msr) || (UICB0_UIC2NCI & uic_msr)) + if ((UIC_MASK(VECNUM_UIC2CI) & uic_msr) || + (UIC_MASK(VECNUM_UIC2NCI) & uic_msr)) uic_interrupt(UIC2_DCR_BASE, 64); #endif #if (UIC_MAX > 3) - if ((UICB0_UIC3CI & uic_msr) || (UICB0_UIC3NCI & uic_msr)) + if ((UIC_MASK(VECNUM_UIC3CI) & uic_msr) || + (UIC_MASK(VECNUM_UIC3NCI) & uic_msr)) uic_interrupt(UIC3_DCR_BASE, 96); #endif -#if defined(CONFIG_440) -#if !defined(CONFIG_440GX) if (uic_msr & ~(UICB0_ALL)) uic_interrupt(UIC0_DCR_BASE, 0); -#else - if ((UICB0_UIC0CI & uic_msr) || (UICB0_UIC0NCI & uic_msr)) - uic_interrupt(UIC0_DCR_BASE, 0); -#endif -#else /* CONFIG_440 */ - uic_interrupt(UIC0_DCR_BASE, 0); -#endif /* CONFIG_440 */ - mtdcr(UIC_BSR, uic_msr); + mtdcr(uic0sr, uic_msr); return; } @@ -308,8 +253,6 @@ void external_interrupt(struct pt_regs *regs) */ void irq_install_handler(int vec, interrupt_handler_t * handler, void *arg) { - int i; - /* * Print warning when replacing with a different irq vector */ @@ -320,20 +263,19 @@ void irq_install_handler(int vec, interrupt_handler_t * handler, void *arg) irq_vecs[vec].handler = handler; irq_vecs[vec].arg = arg; - i = vec & 0x1f; if ((vec >= 0) && (vec < 32)) - mtdcr(uicer, mfdcr(uicer) | (0x80000000 >> i)); + mtdcr(uicer, mfdcr(uicer) | UIC_MASK(vec)); #if (UIC_MAX > 1) else if ((vec >= 32) && (vec < 64)) - mtdcr(uic1er, mfdcr(uic1er) | (0x80000000 >> i)); + mtdcr(uic1er, mfdcr(uic1er) | UIC_MASK(vec)); #endif #if (UIC_MAX > 2) else if ((vec >= 64) && (vec < 96)) - mtdcr(uic2er, mfdcr(uic2er) | (0x80000000 >> i)); + mtdcr(uic2er, mfdcr(uic2er) | UIC_MASK(vec)); #endif #if (UIC_MAX > 3) else if (vec >= 96) - mtdcr(uic3er, mfdcr(uic3er) | (0x80000000 >> i)); + mtdcr(uic3er, mfdcr(uic3er) | UIC_MASK(vec)); #endif debug("Install interrupt for vector %d ==> %p\n", vec, handler); @@ -341,25 +283,22 @@ void irq_install_handler(int vec, interrupt_handler_t * handler, void *arg) void irq_free_handler (int vec) { - int i; - debug("Free interrupt for vector %d ==> %p\n", vec, irq_vecs[vec].handler); - i = vec & 0x1f; if ((vec >= 0) && (vec < 32)) - mtdcr(uicer, mfdcr(uicer) & ~(0x80000000 >> i)); + mtdcr(uicer, mfdcr(uicer) & ~UIC_MASK(vec)); #if (UIC_MAX > 1) else if ((vec >= 32) && (vec < 64)) - mtdcr(uic1er, mfdcr(uic1er) & ~(0x80000000 >> i)); + mtdcr(uic1er, mfdcr(uic1er) & ~UIC_MASK(vec)); #endif #if (UIC_MAX > 2) else if ((vec >= 64) && (vec < 96)) - mtdcr(uic2er, mfdcr(uic2er) & ~(0x80000000 >> i)); + mtdcr(uic2er, mfdcr(uic2er) & ~UIC_MASK(vec)); #endif #if (UIC_MAX > 3) else if (vec >= 96) - mtdcr(uic3er, mfdcr(uic3er) & ~(0x80000000 >> i)); + mtdcr(uic3er, mfdcr(uic3er) & ~UIC_MASK(vec)); #endif irq_vecs[vec].handler = NULL; diff --git a/cpu/ppc4xx/iop480_uart.c b/cpu/ppc4xx/iop480_uart.c index 3af0767..0e3423f 100644 --- a/cpu/ppc4xx/iop480_uart.c +++ b/cpu/ppc4xx/iop480_uart.c @@ -26,7 +26,6 @@ #include <asm/processor.h> #include <asm/io.h> #include <watchdog.h> -#include <asm/ppc4xx-intvec.h> #ifdef CONFIG_SERIAL_MULTI #include <serial.h> diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c index 34bd721..b86b6de 100644 --- a/cpu/ppc4xx/speed.c +++ b/cpu/ppc4xx/speed.c @@ -205,7 +205,8 @@ ulong get_PCI_freq (void) #elif defined(CONFIG_440) -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) static u8 pll_fwdv_multi_bits[] = { /* values for: 1 - 16 */ 0x00, 0x01, 0x0f, 0x04, 0x09, 0x0a, 0x0d, 0x0e, 0x03, 0x0c, diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 426bf3c..97411bd 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -677,7 +677,8 @@ _start: /* not all PPC's have internal SRAM usable as L2-cache */ #if defined(CONFIG_440GX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) mtdcr l2_cache_cfg,r0 /* Ensure L2 Cache is off */ #endif @@ -720,6 +721,19 @@ _start: lis r1,0x4000 /* BAS = 8000_0000 */ ori r1,r1,0x4580 /* 16k */ mtdcr isram0_sb0cr,r1 +#elif defined(CONFIG_460SX) + lis r1,0x0000 /* BAS = 0000_0000 */ + ori r1,r1,0x0B84 /* first 128k */ + mtdcr isram0_sb0cr,r1 + lis r1,0x0001 + ori r1,r1,0x0B84 /* second 128k */ + mtdcr isram0_sb1cr,r1 + lis r1, 0x0002 + ori r1,r1, 0x0B84 /* third 128k */ + mtdcr isram0_sb2cr,r1 + lis r1, 0x0003 + ori r1,r1, 0x0B84 /* fourth 128k */ + mtdcr isram0_sb3cr,r1 #elif defined(CONFIG_440GP) ori r1,r1,0x0380 /* 8k rw */ mtdcr isram0_sb0cr,r1 @@ -1415,7 +1429,8 @@ relocate_code: #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) /* * On some 440er platforms the cache is enabled in the first TLB (Boot-CS) * to speed up the boot process. Now this cache needs to be disabled. diff --git a/cpu/ppc4xx/usbdev.c b/cpu/ppc4xx/usbdev.c index d71ba77..faf7f08 100644 --- a/cpu/ppc4xx/usbdev.c +++ b/cpu/ppc4xx/usbdev.c @@ -6,8 +6,8 @@ #if (defined(CONFIG_440EP) || defined(CONFIG_440EPX)) && defined(CONFIG_CMD_USB) #include <usb.h> +#include <asm/ppc4xx-uic.h> #include "usbdev.h" -#include <asm/ppc4xx-intvec.h> #define USB_DT_DEVICE 0x01 #define USB_DT_CONFIG 0x02 @@ -197,7 +197,7 @@ void usb_dev_init() /*enable interrupts */ *(unsigned char *)USB2D0_INTRUSBE_8 = 0x0f; - irq_install_handler(VECNUM_HSB2D, (interrupt_handler_t *) usbInt, + irq_install_handler(VECNUM_USBDEV, (interrupt_handler_t *) usbInt, NULL); } #else diff --git a/include/asm-ppc/ppc4xx-ebc.h b/include/asm-ppc/ppc4xx-ebc.h new file mode 100644 index 0000000..d180e04 --- /dev/null +++ b/include/asm-ppc/ppc4xx-ebc.h @@ -0,0 +1,156 @@ +/* + * (C) Copyright 2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _PPC4xx_EBC_H_ +#define _PPC4xx_EBC_H_ + +/* + * Currently there are two register layout versions for the + * IBM EBC core used on 4xx PPC's: + */ +#if defined(CONFIG_405CR) || defined(CONFIG_405GP) || \ + defined(CONFIG_405EP) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define CONFIG_EBC_PPC4xx_IBM_VER1 +#endif + +/* Bank Configuration Register */ +#define EBC_BXCR_BAS_MASK PPC_REG_VAL(11, 0xFFF) +#define EBC_BXCR_BAS_ENCODE(n) (((static_cast(u32, n)) & EBC_BXCR_BAS_MASK)) +#define EBC_BXCR_BS_MASK PPC_REG_VAL(14, 0x7) +#define EBC_BXCR_BS_1MB PPC_REG_VAL(14, 0x0) +#define EBC_BXCR_BS_2MB PPC_REG_VAL(14, 0x1) +#define EBC_BXCR_BS_4MB PPC_REG_VAL(14, 0x2) +#define EBC_BXCR_BS_8MB PPC_REG_VAL(14, 0x3) +#define EBC_BXCR_BS_16MB PPC_REG_VAL(14, 0x4) +#define EBC_BXCR_BS_32MB PPC_REG_VAL(14, 0x5) +#define EBC_BXCR_BS_64MB PPC_REG_VAL(14, 0x6) +#define EBC_BXCR_BS_128MB PPC_REG_VAL(14, 0x7) +#define EBC_BXCR_BU_MASK PPC_REG_VAL(16, 0x3) +#define EBC_BXCR_BU_NONE PPC_REG_VAL(16, 0x0) +#define EBC_BXCR_BU_R PPC_REG_VAL(16, 0x1) +#define EBC_BXCR_BU_W PPC_REG_VAL(16, 0x2) +#define EBC_BXCR_BU_RW PPC_REG_VAL(16, 0x3) +#define EBC_BXCR_BW_MASK PPC_REG_VAL(18, 0x3) +#define EBC_BXCR_BW_8BIT PPC_REG_VAL(18, 0x0) +#define EBC_BXCR_BW_16BIT PPC_REG_VAL(18, 0x1) +#if defined(CONFIG_EBC_PPC4xx_IBM_VER1) +#define EBC_BXCR_BW_32BIT PPC_REG_VAL(18, 0x2) +#else +#define EBC_BXCR_BW_32BIT PPC_REG_VAL(18, 0x3) +#endif + +/* Bank Access Parameter Register */ +#define EBC_BXAP_BME_ENABLED PPC_REG_VAL(0, 0x1) +#define EBC_BXAP_BME_DISABLED PPC_REG_VAL(0, 0x0) +#define EBC_BXAP_TWT_ENCODE(n) PPC_REG_VAL(8, (static_cast(u32, n)) & 0xFF) +#define EBC_BXAP_FWT_ENCODE(n) PPC_REG_VAL(5, (static_cast(u32, n)) & 0x1F) +#define EBC_BXAP_BWT_ENCODE(n) PPC_REG_VAL(8, (static_cast(u32, n)) & 0x7) +#define EBC_BXAP_BCE_DISABLE PPC_REG_VAL(9, 0x0) +#define EBC_BXAP_BCE_ENABLE PPC_REG_VAL(9, 0x1) +#define EBC_BXAP_BCT_MASK PPC_REG_VAL(11, 0x3) +#define EBC_BXAP_BCT_2TRANS PPC_REG_VAL(11, 0x0) +#define EBC_BXAP_BCT_4TRANS PPC_REG_VAL(11, 0x1) +#define EBC_BXAP_BCT_8TRANS PPC_REG_VAL(11, 0x2) +#define EBC_BXAP_BCT_16TRANS PPC_REG_VAL(11, 0x3) +#define EBC_BXAP_CSN_ENCODE(n) PPC_REG_VAL(13, (static_cast(u32, n)) & 0x3) +#define EBC_BXAP_OEN_ENCODE(n) PPC_REG_VAL(15, (static_cast(u32, n)) & 0x3) +#define EBC_BXAP_WBN_ENCODE(n) PPC_REG_VAL(17, (static_cast(u32, n)) & 0x3) +#define EBC_BXAP_WBF_ENCODE(n) PPC_REG_VAL(19, (static_cast(u32, n)) & 0x3) +#define EBC_BXAP_TH_ENCODE(n) PPC_REG_VAL(22, (static_cast(u32, n)) & 0x7) +#define EBC_BXAP_RE_ENABLED PPC_REG_VAL(23, 0x1) +#define EBC_BXAP_RE_DISABLED PPC_REG_VAL(23, 0x0) +#define EBC_BXAP_SOR_DELAYED PPC_REG_VAL(24, 0x0) +#define EBC_BXAP_SOR_NONDELAYED PPC_REG_VAL(24, 0x1) +#define EBC_BXAP_BEM_WRITEONLY PPC_REG_VAL(25, 0x0) +#define EBC_BXAP_BEM_RW PPC_REG_VAL(25, 0x1) +#define EBC_BXAP_PEN_DISABLED PPC_REG_VAL(26, 0x0) +#define EBC_BXAP_PEN_ENABLED PPC_REG_VAL(26, 0x1) + +/* Common fields in EBC0_CFG register */ +#define EBC_CFG_PTD_MASK PPC_REG_VAL(1, 0x1) +#define EBC_CFG_PTD_ENABLE PPC_REG_VAL(1, 0x0) +#define EBC_CFG_PTD_DISABLE PPC_REG_VAL(1, 0x1) +#define EBC_CFG_RTC_MASK PPC_REG_VAL(4, 0x7) +#define EBC_CFG_RTC_16PERCLK PPC_REG_VAL(4, 0x0) +#define EBC_CFG_RTC_32PERCLK PPC_REG_VAL(4, 0x1) +#define EBC_CFG_RTC_64PERCLK PPC_REG_VAL(4, 0x2) +#define EBC_CFG_RTC_128PERCLK PPC_REG_VAL(4, 0x3) +#define EBC_CFG_RTC_256PERCLK PPC_REG_VAL(4, 0x4) +#define EBC_CFG_RTC_512PERCLK PPC_REG_VAL(4, 0x5) +#define EBC_CFG_RTC_1024PERCLK PPC_REG_VAL(4, 0x6) +#define EBC_CFG_RTC_2048PERCLK PPC_REG_VAL(4, 0x7) +#define EBC_CFG_PME_MASK PPC_REG_VAL(14, 0x1) +#define EBC_CFG_PME_DISABLE PPC_REG_VAL(14, 0x0) +#define EBC_CFG_PME_ENABLE PPC_REG_VAL(14, 0x1) +#define EBC_CFG_PMT_MASK PPC_REG_VAL(19, 0x1F) +#define EBC_CFG_PMT_ENCODE(n) PPC_REG_VAL(19, (static_cast(u32, n)) & 0x1F) + +/* Now the two versions of the other bits */ +#if defined(CONFIG_EBC_PPC4xx_IBM_VER1) +#define EBC_CFG_EBTC_MASK PPC_REG_VAL(0, 0x1) +#define EBC_CFG_EBTC_HI PPC_REG_VAL(0, 0x0) +#define EBC_CFG_EBTC_DRIVEN PPC_REG_VAL(0, 0x1) +#define EBC_CFG_EMPH_MASK PPC_REG_VAL(6, 0x3) +#define EBC_CFG_EMPH_ENCODE(n) PPC_REG_VAL(6, (static_cast(u32, n)) & 0x3) +#define EBC_CFG_EMPL_MASK PPC_REG_VAL(8, 0x3) +#define EBC_CFG_EMPL_ENCODE(n) PPC_REG_VAL(8, (static_cast(u32, n)) & 0x3) +#define EBC_CFG_CSTC_MASK PPC_REG_VAL(9, 0x1) +#define EBC_CFG_CSTC_HI PPC_REG_VAL(9, 0x0) +#define EBC_CFG_CSTC_DRIVEN PPC_REG_VAL(9, 0x1) +#define EBC_CFG_BPR_MASK PPC_REG_VAL(11, 0x3) +#define EBC_CFG_BPR_1DW PPC_REG_VAL(11, 0x0) +#define EBC_CFG_BPR_2DW PPC_REG_VAL(11, 0x1) +#define EBC_CFG_BPR_4DW PPC_REG_VAL(11, 0x2) +#define EBC_CFG_EMS_MASK PPC_REG_VAL(13, 0x3) +#define EBC_CFG_EMS_8BIT PPC_REG_VAL(13, 0x0) +#define EBC_CFG_EMS_16BIT PPC_REG_VAL(13, 0x1) +#define EBC_CFG_EMS_32BIT PPC_REG_VAL(13, 0x2) +#else +#define EBC_CFG_LE_MASK PPC_REG_VAL(0, 0x1) +#define EBC_CFG_LE_UNLOCK PPC_REG_VAL(0, 0x0) +#define EBC_CFG_LE_LOCK PPC_REG_VAL(0, 0x1) +#define EBC_CFG_ATC_MASK PPC_REG_VAL(5, 0x1) +#define EBC_CFG_ATC_HI PPC_REG_VAL(5, 0x0) +#define EBC_CFG_ATC_PREVIOUS PPC_REG_VAL(5, 0x1) +#define EBC_CFG_DTC_MASK PPC_REG_VAL(6, 0x1) +#define EBC_CFG_DTC_HI PPC_REG_VAL(6, 0x0) +#define EBC_CFG_DTC_PREVIOUS PPC_REG_VAL(6, 0x1) +#define EBC_CFG_CTC_MASK PPC_REG_VAL(7, 0x1) +#define EBC_CFG_CTC_HI PPC_REG_VAL(7, 0x0) +#define EBC_CFG_CTC_PREVIOUS PPC_REG_VAL(7, 0x1) +#define EBC_CFG_OEO_MASK PPC_REG_VAL(8, 0x1) +#define EBC_CFG_OEO_HI PPC_REG_VAL(8, 0x0) +#define EBC_CFG_OEO_PREVIOUS PPC_REG_VAL(8, 0x1) +#define EBC_CFG_EMC_MASK PPC_REG_VAL(9, 0x1) +#define EBC_CFG_EMC_NONDEFAULT PPC_REG_VAL(9, 0x0) +#define EBC_CFG_EMC_DEFAULT PPC_REG_VAL(9, 0x1) +#define EBC_CFG_PR_MASK PPC_REG_VAL(21, 0x3) +#define EBC_CFG_PR_16 PPC_REG_VAL(21, 0x0) +#define EBC_CFG_PR_32 PPC_REG_VAL(21, 0x1) +#define EBC_CFG_PR_64 PPC_REG_VAL(21, 0x2) +#define EBC_CFG_PR_128 PPC_REG_VAL(21, 0x3) +#endif + +#endif /* _PPC4xx_EBC_H_ */ diff --git a/include/asm-ppc/ppc4xx-intvec.h b/include/asm-ppc/ppc4xx-intvec.h deleted file mode 100644 index 5b45de4..0000000 --- a/include/asm-ppc/ppc4xx-intvec.h +++ /dev/null @@ -1,474 +0,0 @@ -/* -* Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com> -* -* See file CREDITS for list of people who contributed to this -* project. -* -* This program is free software; you can redistribute it and/or -* modify it under the terms of the GNU General Public License as -* published by the Free Software Foundation; either version 2 of -* the License, or (at your option) any later version. -* -* This program is distributed in the hope that it will be useful, -* but WITHOUT ANY WARRANTY; without even the implied warranty of -* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -* GNU General Public License for more details. -* -* You should have received a copy of the GNU General Public License -* along with this program; if not, write to the Free Software -* Foundation, Inc., 59 Temple Place, Suite 330, Boston, -* MA 02111-1307 USA -*/ - -/* - * Interrupt vector number definitions to ease the - * 405 -- 440 porting pain ;-) - * - * NOTE: They're not all here yet ... update as needed. - * - */ - -#ifndef _VECNUMS_H_ -#define _VECNUMS_H_ - -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART 0 */ -#define VECNUM_U1 1 /* UART 1 */ -#define VECNUM_IIC0 2 /* IIC */ -#define VECNUM_KRD 3 /* Kasumi Ready for data */ -#define VECNUM_KDA 4 /* Kasumi Data Available */ -#define VECNUM_PCRW 5 /* PCI command register write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_IIC1 7 /* IIC */ -#define VECNUM_SPI 8 /* SPI */ -#define VECNUM_EPCISER 9 /* External PCI SERR */ -#define VECNUM_MTE 10 /* MAL TXEOB */ -#define VECNUM_MRE 11 /* MAL RXEOB */ -#define VECNUM_D0 12 /* DMA channel 0 */ -#define VECNUM_D1 13 /* DMA channel 1 */ -#define VECNUM_D2 14 /* DMA channel 2 */ -#define VECNUM_D3 15 /* DMA channel 3 */ -#define VECNUM_UD0 16 /* UDMA irq 0 */ -#define VECNUM_UD1 17 /* UDMA irq 1 */ -#define VECNUM_UD2 18 /* UDMA irq 2 */ -#define VECNUM_UD3 19 /* UDMA irq 3 */ -#define VECNUM_HSB2D 20 /* USB2.0 Device */ -#define VECNUM_USBDEV 20 /* USB 1.1/USB 2.0 Device */ -#define VECNUM_OHCI1 21 /* USB2.0 Host OHCI irq 1 */ -#define VECNUM_OHCI2 22 /* USB2.0 Host OHCI irq 2 */ -#define VECNUM_EIP94 23 /* Security EIP94 */ -#define VECNUM_ETH0 24 /* Emac 0 */ -#define VECNUM_ETH1 25 /* Emac 1 */ -#define VECNUM_EHCI 26 /* USB2.0 Host EHCI */ -#define VECNUM_EIR4 27 /* External interrupt 4 */ -#define VECNUM_UIC2NC 28 /* UIC2 non-critical interrupt */ -#define VECNUM_UIC2C 29 /* UIC2 critical interrupt */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_MS (32 + 0) /* MAL SERR */ -#define VECNUM_MTDE (32 + 1) /* MAL TXDE */ -#define VECNUM_MRDE (32 + 2) /* MAL RXDE */ -#define VECNUM_U2 (32 + 3) /* UART 2 */ -#define VECNUM_U3 (32 + 4) /* UART 3 */ -#define VECNUM_EBCO (32 + 5) /* EBCO interrupt status */ -#define VECNUM_NDFC (32 + 6) /* NDFC */ -#define VECNUM_KSLE (32 + 7) /* KASUMI slave error */ -#define VECNUM_CT5 (32 + 8) /* GPT compare timer 5 */ -#define VECNUM_CT6 (32 + 9) /* GPT compare timer 6 */ -#define VECNUM_PLB34I0 (32 + 10) /* PLB3X4X MIRQ0 */ -#define VECNUM_PLB34I1 (32 + 11) /* PLB3X4X MIRQ1 */ -#define VECNUM_PLB34I2 (32 + 12) /* PLB3X4X MIRQ2 */ -#define VECNUM_PLB34I3 (32 + 13) /* PLB3X4X MIRQ3 */ -#define VECNUM_PLB34I4 (32 + 14) /* PLB3X4X MIRQ4 */ -#define VECNUM_PLB34I5 (32 + 15) /* PLB3X4X MIRQ5 */ -#define VECNUM_CT0 (32 + 16) /* GPT compare timer 0 */ -#define VECNUM_CT1 (32 + 17) /* GPT compare timer 1 */ -#define VECNUM_EIR7 (32 + 18) /* External interrupt 7 */ -#define VECNUM_EIR8 (32 + 19) /* External interrupt 8 */ -#define VECNUM_EIR9 (32 + 20) /* External interrupt 9 */ -#define VECNUM_CT2 (32 + 21) /* GPT compare timer 2 */ -#define VECNUM_CT3 (32 + 22) /* GPT compare timer 3 */ -#define VECNUM_CT4 (32 + 23) /* GPT compare timer 4 */ -#define VECNUM_SRE (32 + 24) /* Serial ROM error */ -#define VECNUM_GPTDC (32 + 25) /* GPT decrementer pulse */ -#define VECNUM_RSVD0 (32 + 26) /* Reserved */ -#define VECNUM_EPCIPER (32 + 27) /* External PCI PERR */ -#define VECNUM_EIR0 (32 + 28) /* External interrupt 0 */ -#define VECNUM_EWU0 (32 + 29) /* Ethernet 0 wakeup */ -#define VECNUM_EIR1 (32 + 30) /* External interrupt 1 */ -#define VECNUM_EWU1 (32 + 31) /* Ethernet 1 wakeup */ - -#define VECNUM_TXDE VECNUM_MTDE -#define VECNUM_RXDE VECNUM_MRDE - -/* UIC 2 */ -#define VECNUM_EIR5 (64 + 0) /* External interrupt 5 */ -#define VECNUM_EIR6 (64 + 1) /* External interrupt 6 */ -#define VECNUM_OPB (64 + 2) /* OPB to PLB bridge int stat */ -#define VECNUM_EIR2 (64 + 3) /* External interrupt 2 */ -#define VECNUM_EIR3 (64 + 4) /* External interrupt 3 */ -#define VECNUM_DDR2 (64 + 5) /* DDR2 sdram */ -#define VECNUM_MCTX0 (64 + 6) /* MAl intp coalescence TX0 */ -#define VECNUM_MCTX1 (64 + 7) /* MAl intp coalescence TX1 */ -#define VECNUM_MCTR0 (64 + 8) /* MAl intp coalescence TR0 */ -#define VECNUM_MCTR1 (64 + 9) /* MAl intp coalescence TR1 */ - -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) - -/* UIC 0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_IIC0 2 /* IIC0 */ -#define VECNUM_IIC1 3 /* IIC1 */ -#define VECNUM_PIM 4 /* PCI inbound message */ -#define VECNUM_PCRW 5 /* PCI command reg write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_MSI0 8 /* PCI MSI level 0 */ -#define VECNUM_EIR0 9 /* External interrupt 0 */ -#define VECNUM_UIC2NC 10 /* UIC2 non-critical interrupt */ -#define VECNUM_UIC2C 11 /* UIC2 critical interrupt */ -#define VECNUM_D0 12 /* DMA channel 0 */ -#define VECNUM_D1 13 /* DMA channel 1 */ -#define VECNUM_D2 14 /* DMA channel 2 */ -#define VECNUM_D3 15 /* DMA channel 3 */ -#define VECNUM_UIC3NC 16 /* UIC3 non-critical interrupt */ -#define VECNUM_UIC3C 17 /* UIC3 critical interrupt */ -#define VECNUM_EIR1 9 /* External interrupt 1 */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_EIR2 (32 + 0) /* External interrupt 0 */ -#define VECNUM_U0 (32 + 1) /* UART0 */ -#define VECNUM_EIR3 (32 + 20) /* External interrupt 3 */ -#define VECNUM_EIR4 (32 + 21) /* External interrupt 4 */ -#define VECNUM_EIR5 (32 + 26) /* External interrupt 5 */ -#define VECNUM_EIR6 (32 + 27) /* External interrupt 6 */ -#define VECNUM_U2 (32 + 28) /* UART2 */ -#define VECNUM_U3 (32 + 29) /* UART3 */ -#define VECNUM_EIR7 (32 + 30) /* External interrupt 7 */ -#define VECNUM_EIR8 (32 + 31) /* External interrupt 8 */ - -/* UIC 2 */ -#define VECNUM_EIR9 (64 + 2) /* External interrupt 9 */ -#define VECNUM_MS (64 + 3) /* MAL SERR */ -#define VECNUM_TXDE (64 + 4) /* MAL TXDE */ -#define VECNUM_RXDE (64 + 5) /* MAL RXDE */ -#define VECNUM_MTE (64 + 6) /* MAL TXEOB */ -#define VECNUM_MRE (64 + 7) /* MAL RXEOB */ -#define VECNUM_ETH0 (64 + 16) /* Ethernet 0 */ -#define VECNUM_ETH1 (64 + 17) /* Ethernet 1 */ -#define VECNUM_ETH2 (64 + 18) /* Ethernet 2 */ -#define VECNUM_ETH3 (64 + 19) /* Ethernet 3 */ -#define VECNUM_EWU0 (64 + 20) /* Emac 0 wakeup */ -#define VECNUM_EWU1 (64 + 21) /* Emac 1 wakeup */ -#define VECNUM_EWU2 (64 + 22) /* Emac 2 wakeup */ -#define VECNUM_EWU3 (64 + 23) /* Emac 3 wakeup */ -#define VECNUM_EIR10 (64 + 24) /* External interrupt 10 */ -#define VECNUM_EIR11 (64 + 25) /* External interrupt 11 */ - -/* UIC 3 */ -#define VECNUM_EIR12 (96 + 20) /* External interrupt 20 */ -#define VECNUM_EIR13 (96 + 21) /* External interrupt 21 */ -#define VECNUM_EIR14 (96 + 22) /* External interrupt 22 */ -#define VECNUM_EIR15 (96 + 23) /* External interrupt 23 */ -#define VECNUM_PCIEMSI0 (96 + 24) /* PCI Express MSI level 0 */ -#define VECNUM_PCIEMSI1 (96 + 25) /* PCI Express MSI level 1 */ -#define VECNUM_PCIEMSI2 (96 + 26) /* PCI Express MSI level 2 */ -#define VECNUM_PCIEMSI3 (96 + 27) /* PCI Express MSI level 3 */ -#define VECNUM_PCIEMSI4 (96 + 28) /* PCI Express MSI level 4 */ -#define VECNUM_PCIEMSI5 (96 + 29) /* PCI Express MSI level 5 */ -#define VECNUM_PCIEMSI6 (96 + 30) /* PCI Express MSI level 6 */ -#define VECNUM_PCIEMSI7 (96 + 31) /* PCI Express MSI level 7 */ - -#elif defined(CONFIG_440SPE) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_IIC0 2 /* IIC0 */ -#define VECNUM_IIC1 3 /* IIC1 */ -#define VECNUM_PIM 4 /* PCI inbound message */ -#define VECNUM_PCRW 5 /* PCI command reg write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_MSI0 7 /* PCI MSI level 0 */ -#define VECNUM_MSI1 8 /* PCI MSI level 0 */ -#define VECNUM_MSI2 9 /* PCI MSI level 0 */ -#define VECNUM_UIC2NC 10 /* UIC2 non-critical interrupt */ -#define VECNUM_UIC2C 11 /* UIC2 critical interrupt */ -#define VECNUM_D0 12 /* DMA channel 0 */ -#define VECNUM_D1 13 /* DMA channel 1 */ -#define VECNUM_D2 14 /* DMA channel 2 */ -#define VECNUM_D3 15 /* DMA channel 3 */ -#define VECNUM_UIC3NC 16 /* UIC3 non-critical interrupt */ -#define VECNUM_UIC3C 17 /* UIC3 critical interrupt */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_MS (32 + 1 ) /* MAL SERR */ -#define VECNUM_TXDE (32 + 2 ) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 3 ) /* MAL RXDE */ -#define VECNUM_MTE (32 + 6 ) /* MAL Tx EOB */ -#define VECNUM_MRE (32 + 7 ) /* MAL Rx EOB */ -#define VECNUM_CT0 (32 + 12 ) /* GPT compare timer 0 */ -#define VECNUM_CT1 (32 + 13 ) /* GPT compare timer 1 */ -#define VECNUM_CT2 (32 + 14 ) /* GPT compare timer 2 */ -#define VECNUM_CT3 (32 + 15 ) /* GPT compare timer 3 */ -#define VECNUM_CT4 (32 + 16 ) /* GPT compare timer 4 */ -#define VECNUM_ETH0 (32 + 28) /* Ethernet interrupt status */ -#define VECNUM_EWU0 (32 + 29) /* Emac wakeup */ - -/* UIC 2 */ -#define VECNUM_EIR5 (64 + 24) /* External interrupt 5 */ -#define VECNUM_EIR4 (64 + 25) /* External interrupt 4 */ -#define VECNUM_EIR3 (64 + 26) /* External interrupt 3 */ -#define VECNUM_EIR2 (64 + 27) /* External interrupt 2 */ -#define VECNUM_EIR1 (64 + 28) /* External interrupt 1 */ -#define VECNUM_EIR0 (64 + 29) /* External interrupt 0 */ - -#elif defined(CONFIG_440SP) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_IIC0 2 /* IIC0 */ -#define VECNUM_IIC1 3 /* IIC1 */ -#define VECNUM_PIM 4 /* PCI inbound message */ -#define VECNUM_PCRW 5 /* PCI command reg write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_EIR0 (32 + 0) /* External interrupt 0 */ -#define VECNUM_MS (32 + 1) /* MAL SERR */ -#define VECNUM_TXDE (32 + 2) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 3) /* MAL RXDE */ -#define VECNUM_MTE (32 + 6) /* MAL Tx EOB */ -#define VECNUM_MRE (32 + 7) /* MAL Rx EOB */ -#define VECNUM_CT0 (32 + 12) /* GPT compare timer 0 */ -#define VECNUM_CT1 (32 + 13) /* GPT compare timer 1 */ -#define VECNUM_CT2 (32 + 14) /* GPT compare timer 2 */ -#define VECNUM_CT3 (32 + 15) /* GPT compare timer 3 */ -#define VECNUM_CT4 (32 + 16) /* GPT compare timer 4 */ -#define VECNUM_ETH0 (32 + 28) /* Ethernet interrupt status */ -#define VECNUM_EWU0 (32 + 29) /* Emac wakeup */ - -#elif defined(CONFIG_440) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_IIC0 2 /* IIC0 */ -#define VECNUM_IIC1 3 /* IIC1 */ -#define VECNUM_PIM 4 /* PCI inbound message */ -#define VECNUM_PCRW 5 /* PCI command reg write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_MSI0 7 /* PCI MSI level 0 */ -#define VECNUM_MSI1 8 /* PCI MSI level 0 */ -#define VECNUM_MSI2 9 /* PCI MSI level 0 */ -#define VECNUM_MTE 10 /* MAL TXEOB */ -#define VECNUM_MRE 11 /* MAL RXEOB */ -#define VECNUM_D0 12 /* DMA channel 0 */ -#define VECNUM_D1 13 /* DMA channel 1 */ -#define VECNUM_D2 14 /* DMA channel 2 */ -#define VECNUM_D3 15 /* DMA channel 3 */ -#define VECNUM_CT0 18 /* GPT compare timer 0 */ -#define VECNUM_CT1 19 /* GPT compare timer 1 */ -#define VECNUM_CT2 20 /* GPT compare timer 2 */ -#define VECNUM_CT3 21 /* GPT compare timer 3 */ -#define VECNUM_CT4 22 /* GPT compare timer 4 */ -#define VECNUM_EIR0 23 /* External interrupt 0 */ -#define VECNUM_EIR1 24 /* External interrupt 1 */ -#define VECNUM_EIR2 25 /* External interrupt 2 */ -#define VECNUM_EIR3 26 /* External interrupt 3 */ -#define VECNUM_EIR4 27 /* External interrupt 4 */ -#define VECNUM_EIR5 28 /* External interrupt 5 */ -#define VECNUM_EIR6 29 /* External interrupt 6 */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_MS (32 + 0 ) /* MAL SERR */ -#define VECNUM_TXDE (32 + 1 ) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 2 ) /* MAL RXDE */ -#define VECNUM_USBDEV (32 + 23) /* USB 1.1/USB 2.0 Device */ -#define VECNUM_ETH0 (32 + 28) /* Ethernet 0 interrupt status */ -#define VECNUM_EWU0 (32 + 29) /* Ethernet 0 wakeup */ - -#else /* !defined(CONFIG_440) */ - -#if defined(CONFIG_405EZ) -#define VECNUM_D0 0 /* DMA channel 0 */ -#define VECNUM_D1 1 /* DMA channel 1 */ -#define VECNUM_D2 2 /* DMA channel 2 */ -#define VECNUM_D3 3 /* DMA channel 3 */ -#define VECNUM_1588 4 /* IEEE 1588 network synchronization */ -#define VECNUM_U0 5 /* UART0 */ -#define VECNUM_U1 6 /* UART1 */ -#define VECNUM_CAN0 7 /* CAN 0 */ -#define VECNUM_CAN1 8 /* CAN 1 */ -#define VECNUM_SPI 9 /* SPI */ -#define VECNUM_IIC0 10 /* I2C */ -#define VECNUM_CHT0 11 /* Chameleon timer high pri interrupt */ -#define VECNUM_CHT1 12 /* Chameleon timer high pri interrupt */ -#define VECNUM_USBH1 13 /* USB Host 1 */ -#define VECNUM_USBH2 14 /* USB Host 2 */ -#define VECNUM_USBDEV 15 /* USB Device */ -#define VECNUM_ETH0 16 /* 10/100 Ethernet interrupt status */ -#define VECNUM_EWU0 17 /* Ethernet wakeup sequence detected */ - -#define VECNUM_MADMAL 18 /* Logical OR of following MadMAL int */ -#define VECNUM_MS 18 /* MAL_SERR_INT */ -#define VECNUM_TXDE 18 /* MAL_TXDE_INT */ -#define VECNUM_RXDE 18 /* MAL_RXDE_INT */ - -#define VECNUM_MTE 19 /* MAL TXEOB */ -#define VECNUM_MTE1 20 /* MAL TXEOB1 */ -#define VECNUM_MRE 21 /* MAL RXEOB */ -#define VECNUM_NAND 22 /* NAND Flash controller */ -#define VECNUM_ADC 23 /* ADC */ -#define VECNUM_DAC 24 /* DAC */ -#define VECNUM_OPB2PLB 25 /* OPB to PLB bridge interrupt */ -#define VECNUM_RESERVED0 26 /* Reserved */ -#define VECNUM_EIR0 27 /* External interrupt 0 */ -#define VECNUM_EIR1 28 /* External interrupt 1 */ -#define VECNUM_EIR2 29 /* External interrupt 2 */ -#define VECNUM_EIR3 30 /* External interrupt 3 */ -#define VECNUM_EIR4 31 /* External interrupt 4 */ - -#elif defined(CONFIG_405EX) - -/* UIC 0 */ -#define VECNUM_U0 00 -#define VECNUM_U1 01 -#define VECNUM_IIC0 02 -#define VECNUM_PKA 03 -#define VECNUM_TRNG 04 -#define VECNUM_EBM 05 -#define VECNUM_BGI 06 -#define VECNUM_IIC1 07 -#define VECNUM_SPI 08 -#define VECNUM_EIR0 09 -#define VECNUM_MTE 10 /* MAL Tx EOB */ -#define VECNUM_MRE 11 /* MAL Rx EOB */ -#define VECNUM_DMA0 12 -#define VECNUM_DMA1 13 -#define VECNUM_DMA2 14 -#define VECNUM_DMA3 15 -#define VECNUM_PCIE0AL 16 -#define VECNUM_PCIE0VPD 17 -#define VECNUM_RPCIE0HRST 18 -#define VECNUM_FPCIE0HRST 19 -#define VECNUM_PCIE0TCR 20 -#define VECNUM_PCIEMSI0 21 -#define VECNUM_PCIEMSI1 22 -#define VECNUM_SECURITY 23 -#define VECNUM_ETH0 24 -#define VECNUM_ETH1 25 -#define VECNUM_PCIEMSI2 26 -#define VECNUM_EIR4 27 -#define VECNUM_UIC2NC 28 -#define VECNUM_UIC2C 29 -#define VECNUM_UIC1NC 30 -#define VECNUM_UIC1C 31 - -/* UIC 1 */ -#define VECNUM_MS (32 + 00) /* MAL SERR */ -#define VECNUM_TXDE (32 + 01) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 02) /* MAL RXDE */ -#define VECNUM_PCIE0BMVC0 (32 + 03) -#define VECNUM_PCIE0DCRERR (32 + 04) -#define VECNUM_EBC (32 + 05) -#define VECNUM_NDFC (32 + 06) -#define VECNUM_PCEI1DCRERR (32 + 07) -#define VECNUM_CT8 (32 + 08) -#define VECNUM_CT9 (32 + 09) -#define VECNUM_PCIE1AL (32 + 10) -#define VECNUM_PCIE1VPD (32 + 11) -#define VECNUM_RPCE1HRST (32 + 12) -#define VECNUM_FPCE1HRST (32 + 13) -#define VECNUM_PCIE1TCR (32 + 14) -#define VECNUM_PCIE1VC0 (32 + 15) -#define VECNUM_CT3 (32 + 16) -#define VECNUM_CT4 (32 + 17) -#define VECNUM_EIR7 (32 + 18) -#define VECNUM_EIR8 (32 + 19) -#define VECNUM_EIR9 (32 + 20) -#define VECNUM_CT5 (32 + 21) -#define VECNUM_CT6 (32 + 22) -#define VECNUM_CT7 (32 + 23) -#define VECNUM_SROM (32 + 24) /* SERIAL ROM */ -#define VECNUM_GPTDECPULS (32 + 25) /* GPT Decrement pulse */ -#define VECNUM_EIR2 (32 + 26) -#define VECNUM_EIR5 (32 + 27) -#define VECNUM_EIR6 (32 + 28) -#define VECNUM_EMAC0WAKE (32 + 29) -#define VECNUM_EIR1 (32 + 30) -#define VECNUM_EMAC1WAKE (32 + 31) - -/* UIC 2 */ -#define VECNUM_PCIE0INTA (64 + 00) /* PCIE0 INTA */ -#define VECNUM_PCIE0INTB (64 + 01) /* PCIE0 INTB */ -#define VECNUM_PCIE0INTC (64 + 02) /* PCIE0 INTC */ -#define VECNUM_PCIE0INTD (64 + 03) /* PCIE0 INTD */ -#define VECNUM_EIR3 (64 + 04) /* External IRQ 3 */ -#define VECNUM_DDRMCUE (64 + 05) -#define VECNUM_DDRMCCE (64 + 06) -#define VECNUM_MALINTCOATX0 (64 + 07) /* Interrupt coalecence TX0 */ -#define VECNUM_MALINTCOATX1 (64 + 08) /* Interrupt coalecence TX1 */ -#define VECNUM_MALINTCOARX0 (64 + 09) /* Interrupt coalecence RX0 */ -#define VECNUM_MALINTCOARX1 (64 + 10) /* Interrupt coalecence RX1 */ -#define VECNUM_PCIE1INTA (64 + 11) /* PCIE0 INTA */ -#define VECNUM_PCIE1INTB (64 + 12) /* PCIE0 INTB */ -#define VECNUM_PCIE1INTC (64 + 13) /* PCIE0 INTC */ -#define VECNUM_PCIE1INTD (64 + 14) /* PCIE0 INTD */ -#define VECNUM_RPCIEMSI2 (64 + 15) /* MSI level 2 */ -#define VECNUM_PCIEMSI3 (64 + 16) /* MSI level 2 */ -#define VECNUM_PCIEMSI4 (64 + 17) /* MSI level 2 */ -#define VECNUM_PCIEMSI5 (64 + 18) /* MSI level 2 */ -#define VECNUM_PCIEMSI6 (64 + 19) /* MSI level 2 */ -#define VECNUM_PCIEMSI7 (64 + 20) /* MSI level 2 */ -#define VECNUM_PCIEMSI8 (64 + 21) /* MSI level 2 */ -#define VECNUM_PCIEMSI9 (64 + 22) /* MSI level 2 */ -#define VECNUM_PCIEMSI10 (64 + 23) /* MSI level 2 */ -#define VECNUM_PCIEMSI11 (64 + 24) /* MSI level 2 */ -#define VECNUM_PCIEMSI12 (64 + 25) /* MSI level 2 */ -#define VECNUM_PCIEMSI13 (64 + 26) /* MSI level 2 */ -#define VECNUM_PCIEMSI14 (64 + 27) /* MSI level 2 */ -#define VECNUM_PCIEMSI15 (64 + 28) /* MSI level 2 */ -#define VECNUM_PLB4XAHB (64 + 29) /* PLBxAHB bridge */ -#define VECNUM_USBWAKE (64 + 30) /* USB wakup */ -#define VECNUM_USBOTG (64 + 31) /* USB OTG */ - -#else /* !CONFIG_405EZ */ - -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_D0 5 /* DMA channel 0 */ -#define VECNUM_D1 6 /* DMA channel 1 */ -#define VECNUM_D2 7 /* DMA channel 2 */ -#define VECNUM_D3 8 /* DMA channel 3 */ -#define VECNUM_EWU0 9 /* Ethernet wakeup */ -#define VECNUM_MS 10 /* MAL SERR */ -#define VECNUM_MTE 11 /* MAL TXEOB */ -#define VECNUM_MRE 12 /* MAL RXEOB */ -#define VECNUM_TXDE 13 /* MAL TXDE */ -#define VECNUM_RXDE 14 /* MAL RXDE */ -#define VECNUM_ETH0 15 /* Ethernet interrupt status */ -#define VECNUM_EIR0 25 /* External interrupt 0 */ -#define VECNUM_EIR1 26 /* External interrupt 1 */ -#define VECNUM_EIR2 27 /* External interrupt 2 */ -#define VECNUM_EIR3 28 /* External interrupt 3 */ -#define VECNUM_EIR4 29 /* External interrupt 4 */ -#define VECNUM_EIR5 30 /* External interrupt 5 */ -#define VECNUM_EIR6 31 /* External interrupt 6 */ -#endif /* defined(CONFIG_405EZ) */ - -#endif /* defined(CONFIG_440) */ - -#endif /* _VECNUMS_H_ */ diff --git a/include/asm-ppc/ppc4xx-sdram.h b/include/asm-ppc/ppc4xx-sdram.h index e151f0c..df787b3 100644 --- a/include/asm-ppc/ppc4xx-sdram.h +++ b/include/asm-ppc/ppc4xx-sdram.h @@ -282,7 +282,8 @@ * Memory Bank 0-7 configuration */ #if defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) #define SDRAM_RXBAS_SDBA_MASK 0xFFE00000 /* Base address */ #define SDRAM_RXBAS_SDBA_ENCODE(n) ((u32)(((phys_size_t)(n) >> 2) & 0xFFE00000)) #define SDRAM_RXBAS_SDBA_DECODE(n) ((((phys_size_t)(n)) & 0xFFE00000) << 2) @@ -353,7 +354,19 @@ /* * Memory controller registers */ +#define SDRAM_BESR 0x00 /* PLB bus error status (read/clear) */ +#define SDRAM_BESRT 0x01 /* PLB bus error status (test/set) */ +#define SDRAM_BEARL 0x02 /* PLB bus error address low */ +#define SDRAM_BEARH 0x03 /* PLB bus error address high */ +#define SDRAM_WMIRQ 0x06 /* PLB write master interrupt (read/clear) */ +#define SDRAM_WMIRQT 0x07 /* PLB write master interrupt (test/set) */ +#define SDRAM_PLBOPT 0x08 /* PLB slave options */ +#define SDRAM_PUABA 0x09 /* PLB upper address base */ +#ifndef CONFIG_405EX #define SDRAM_MCSTAT 0x14 /* memory controller status */ +#else +#define SDRAM_MCSTAT 0x1F /* memory controller status */ +#endif #define SDRAM_MCOPT1 0x20 /* memory controller options 1 */ #define SDRAM_MCOPT2 0x21 /* memory controller options 2 */ #define SDRAM_MODT0 0x22 /* on die termination for bank 0 */ @@ -398,9 +411,35 @@ #define SDRAM_MMODE 0x88 /* memory mode */ #define SDRAM_MEMODE 0x89 /* memory extended mode */ #define SDRAM_ECCCR 0x98 /* ECC error status */ +#define SDRAM_ECCES SDRAM_ECCCR #define SDRAM_CID 0xA4 /* core ID */ +#ifndef CONFIG_405EX #define SDRAM_RID 0xA8 /* revision ID */ +#endif +#define SDRAM_FCSR 0xB0 /* feedback calibration status */ #define SDRAM_RTSR 0xB1 /* run time status tracking */ +#ifdef CONFIG_405EX +#define SDRAM_RID 0xF8 /* revision ID */ +#endif + +/* + * Memory Controller Bus Error Status + */ +#define SDRAM_BESR_MASK PPC_REG_VAL(7, 0xFF) +#define SDRAM_BESR_M0ID_MASK PPC_REG_VAL(3, 0xF) +#define SDRAM_BESR_M0ID_ICU PPC_REG_VAL(3, 0x0) +#define SDRAM_BESR_M0ID_PCIE0 PPC_REG_VAL(3, 0x1) +#define SDRAM_BESR_M0ID_PCIE1 PPC_REG_VAL(3, 0x2) +#define SDRAM_BESR_M0ID_DMA PPC_REG_VAL(3, 0x3) +#define SDRAM_BESR_M0ID_DCU PPC_REG_VAL(3, 0x4) +#define SDRAM_BESR_M0ID_OPB PPC_REG_VAL(3, 0x5) +#define SDRAM_BESR_M0ID_MAL PPC_REG_VAL(3, 0x6) +#define SDRAM_BESR_M0ID_SEC PPC_REG_VAL(3, 0x7) +#define SDRAM_BESR_M0ET_MASK PPC_REG_VAL(6, 0x7) +#define SDRAM_BESR_M0ET_NONE PPC_REG_VAL(6, 0x0) +#define SDRAM_BESR_M0ET_ECC PPC_REG_VAL(6, 0x1) +#define SDRAM_BESR_M0RW_WRITE PPC_REG_VAL(7, 0) +#define SDRAM_BESR_M0RW_READ PPC_REG_VAL(8, 1) /* * Memory Controller Status @@ -523,7 +562,7 @@ * SDRAM Delay Line Calibration Register */ #define SDRAM_DLCR_DCLM_MASK 0x80000000 -#define SDRAM_DLCR_DCLM_MANUEL 0x80000000 +#define SDRAM_DLCR_DCLM_MANUAL 0x80000000 #define SDRAM_DLCR_DCLM_AUTO 0x00000000 #define SDRAM_DLCR_DLCR_MASK 0x08000000 #define SDRAM_DLCR_DLCR_CALIBRATE 0x08000000 @@ -539,59 +578,234 @@ #define SDRAM_DLCR_DLCV_DECODE(n) ((((u32)(n))>>0)&0x1FF) /* + * SDRAM Memory On Die Terimination Control Register + */ +#define SDRAM_MODT_ODTON_DISABLE PPC_REG_VAL(0, 0) +#define SDRAM_MODT_ODTON_ENABLE PPC_REG_VAL(0, 1) +#define SDRAM_MODT_EB1W_DISABLE PPC_REG_VAL(1, 0) +#define SDRAM_MODT_EB1W_ENABLE PPC_REG_VAL(1, 1) +#define SDRAM_MODT_EB1R_DISABLE PPC_REG_VAL(2, 0) +#define SDRAM_MODT_EB1R_ENABLE PPC_REG_VAL(2, 1) +#define SDRAM_MODT_EB0W_DISABLE PPC_REG_VAL(7, 0) +#define SDRAM_MODT_EB0W_ENABLE PPC_REG_VAL(7, 1) +#define SDRAM_MODT_EB0R_DISABLE PPC_REG_VAL(8, 0) +#define SDRAM_MODT_EB0R_ENABLE PPC_REG_VAL(8, 1) + +/* * SDRAM Controller On Die Termination Register */ -#define SDRAM_CODT_ODT_ON 0x80000000 -#define SDRAM_CODT_ODT_OFF 0x00000000 -#define SDRAM_CODT_DQS_VOLTAGE_DDR_MASK 0x00000020 -#define SDRAM_CODT_DQS_2_5_V_DDR1 0x00000000 -#define SDRAM_CODT_DQS_1_8_V_DDR2 0x00000020 -#define SDRAM_CODT_DQS_MASK 0x00000010 -#define SDRAM_CODT_DQS_DIFFERENTIAL 0x00000000 -#define SDRAM_CODT_DQS_SINGLE_END 0x00000010 -#define SDRAM_CODT_CKSE_DIFFERENTIAL 0x00000000 -#define SDRAM_CODT_CKSE_SINGLE_END 0x00000008 -#define SDRAM_CODT_FEEBBACK_RCV_SINGLE_END 0x00000004 -#define SDRAM_CODT_FEEBBACK_DRV_SINGLE_END 0x00000002 -#define SDRAM_CODT_IO_HIZ 0x00000000 -#define SDRAM_CODT_IO_NMODE 0x00000001 +#define SDRAM_CODT_ODT_ON PPC_REG_VAL(0, 1) +#define SDRAM_CODT_ODT_OFF PPC_REG_VAL(0, 0) +#define SDRAM_CODT_RK1W_ON PPC_REG_VAL(1, 1) +#define SDRAM_CODT_RK1W_OFF PPC_REG_VAL(1, 0) +#define SDRAM_CODT_RK1R_ON PPC_REG_VAL(2, 1) +#define SDRAM_CODT_RK1R_OFF PPC_REG_VAL(2, 0) +#define SDRAM_CODT_RK0W_ON PPC_REG_VAL(7, 1) +#define SDRAM_CODT_RK0W_OFF PPC_REG_VAL(7, 0) +#define SDRAM_CODT_RK0R_ON PPC_REG_VAL(8, 1) +#define SDRAM_CODT_RK0R_OFF PPC_REG_VAL(8, 0) +#define SDRAM_CODT_ODTSH_NORMAL PPC_REG_VAL(10, 0) +#define SDRAM_CODT_ODTSH_REMOVE_ONE_AT_END PPC_REG_VAL(10, 1) +#define SDRAM_CODT_ODTSH_ADD_ONE_AT_START PPC_REG_VAL(10, 2) +#define SDRAM_CODT_ODTSH_SHIFT_ONE_EARLIER PPC_REG_VAL(10, 3) +#define SDRAM_CODT_CODTZ_75OHM PPC_REG_VAL(11, 0) +#define SDRAM_CODT_CKEG_ON PPC_REG_VAL(12, 1) +#define SDRAM_CODT_CKEG_OFF PPC_REG_VAL(12, 0) +#define SDRAM_CODT_CTLG_ON PPC_REG_VAL(13, 1) +#define SDRAM_CODT_CTLG_OFF PPC_REG_VAL(13, 0) +#define SDRAM_CODT_FBDG_ON PPC_REG_VAL(14, 1) +#define SDRAM_CODT_FBDG_OFF PPC_REG_VAL(14, 0) +#define SDRAM_CODT_FBRG_ON PPC_REG_VAL(15, 1) +#define SDRAM_CODT_FBRG_OFF PPC_REG_VAL(15, 0) +#define SDRAM_CODT_CKLZ_36OHM PPC_REG_VAL(18, 1) +#define SDRAM_CODT_CKLZ_18OHM PPC_REG_VAL(18, 0) +#define SDRAM_CODT_DQS_VOLTAGE_DDR_MASK PPC_REG_VAL(26, 1) +#define SDRAM_CODT_DQS_2_5_V_DDR1 PPC_REG_VAL(26, 0) +#define SDRAM_CODT_DQS_1_8_V_DDR2 PPC_REG_VAL(26, 1) +#define SDRAM_CODT_DQS_MASK PPC_REG_VAL(27, 1) +#define SDRAM_CODT_DQS_DIFFERENTIAL PPC_REG_VAL(27, 0) +#define SDRAM_CODT_DQS_SINGLE_END PPC_REG_VAL(27, 1) +#define SDRAM_CODT_CKSE_DIFFERENTIAL PPC_REG_VAL(28, 0) +#define SDRAM_CODT_CKSE_SINGLE_END PPC_REG_VAL(28, 1) +#define SDRAM_CODT_FEEBBACK_RCV_SINGLE_END PPC_REG_VAL(29, 1) +#define SDRAM_CODT_FEEBBACK_DRV_SINGLE_END PPC_REG_VAL(30, 1) +#define SDRAM_CODT_IO_HIZ PPC_REG_VAL(31, 0) +#define SDRAM_CODT_IO_NMODE PPC_REG_VAL(31, 1) /* - * SDRAM Mode Register + * SDRAM Initialization Preload Register */ -#define SDRAM_MMODE_WR_MASK 0x00000E00 -#define SDRAM_MMODE_WR_DDR1 0x00000000 -#define SDRAM_MMODE_WR_DDR2_3_CYC 0x00000400 -#define SDRAM_MMODE_WR_DDR2_4_CYC 0x00000600 -#define SDRAM_MMODE_WR_DDR2_5_CYC 0x00000800 -#define SDRAM_MMODE_WR_DDR2_6_CYC 0x00000A00 -#define SDRAM_MMODE_DCL_MASK 0x00000070 -#define SDRAM_MMODE_DCL_DDR1_2_0_CLK 0x00000020 -#define SDRAM_MMODE_DCL_DDR1_2_5_CLK 0x00000060 -#define SDRAM_MMODE_DCL_DDR1_3_0_CLK 0x00000030 -#define SDRAM_MMODE_DCL_DDR2_2_0_CLK 0x00000020 -#define SDRAM_MMODE_DCL_DDR2_3_0_CLK 0x00000030 -#define SDRAM_MMODE_DCL_DDR2_4_0_CLK 0x00000040 -#define SDRAM_MMODE_DCL_DDR2_5_0_CLK 0x00000050 -#define SDRAM_MMODE_DCL_DDR2_6_0_CLK 0x00000060 -#define SDRAM_MMODE_DCL_DDR2_7_0_CLK 0x00000070 +#define SDRAM_INITPLR_ENABLE PPC_REG_VAL(0, 1) +#define SDRAM_INITPLR_DISABLE PPC_REG_VAL(0, 0) +#define SDRAM_INITPLR_IMWT_MASK PPC_REG_VAL(8, 0xFF) +#define SDRAM_INITPLR_IMWT_ENCODE(n) PPC_REG_VAL(8, \ + (static_cast(u32, \ + n)) \ + & 0xFF) +#define SDRAM_INITPLR_ICMD_MASK PPC_REG_VAL(12, 0x7) +#define SDRAM_INITPLR_ICMD_ENCODE(n) PPC_REG_VAL(12, \ + (static_cast(u32, \ + n)) \ + & 0x7) +#define SDRAM_INITPLR_IBA_MASK PPC_REG_VAL(15, 0x7) +#define SDRAM_INITPLR_IBA_ENCODE(n) PPC_REG_VAL(15, \ + (static_cast(u32, \ + n)) \ + & 0x7) +#define SDRAM_INITPLR_IMA_MASK PPC_REG_VAL(31, 0x7FFF) +#define SDRAM_INITPLR_IMA_ENCODE(n) PPC_REG_VAL(31, \ + (static_cast(u32, \ + n)) \ + & 0x7FFF) /* - * SDRAM Extended Mode Register + * JEDEC DDR Initialization Commands */ -#define SDRAM_MEMODE_DIC_MASK 0x00000002 -#define SDRAM_MEMODE_DIC_NORMAL 0x00000000 -#define SDRAM_MEMODE_DIC_WEAK 0x00000002 -#define SDRAM_MEMODE_DLL_MASK 0x00000001 -#define SDRAM_MEMODE_DLL_DISABLE 0x00000001 -#define SDRAM_MEMODE_DLL_ENABLE 0x00000000 -#define SDRAM_MEMODE_RTT_MASK 0x00000044 -#define SDRAM_MEMODE_RTT_DISABLED 0x00000000 -#define SDRAM_MEMODE_RTT_75OHM 0x00000004 -#define SDRAM_MEMODE_RTT_150OHM 0x00000040 -#define SDRAM_MEMODE_DQS_MASK 0x00000400 -#define SDRAM_MEMODE_DQS_DISABLE 0x00000400 -#define SDRAM_MEMODE_DQS_ENABLE 0x00000000 +#define JEDEC_CMD_NOP 7 +#define JEDEC_CMD_PRECHARGE 2 +#define JEDEC_CMD_REFRESH 1 +#define JEDEC_CMD_EMR 0 +#define JEDEC_CMD_READ 5 +#define JEDEC_CMD_WRITE 4 + +/* + * JEDEC Precharge Command Memory Address Arguments + */ +#define JEDEC_MA_PRECHARGE_ONE (0 << 10) +#define JEDEC_MA_PRECHARGE_ALL (1 << 10) + +/* + * JEDEC DDR EMR Command Bank Address Arguments + */ +#define JEDEC_BA_MR 0 +#define JEDEC_BA_EMR 1 +#define JEDEC_BA_EMR2 2 +#define JEDEC_BA_EMR3 3 + +/* + * JEDEC DDR Mode Register + */ +#define JEDEC_MA_MR_PDMODE_FAST_EXIT (0 << 12) +#define JEDEC_MA_MR_PDMODE_SLOW_EXIT (1 << 12) +#define JEDEC_MA_MR_WR_MASK (0x7 << 9) +#define JEDEC_MA_MR_WR_DDR1 (0x0 << 9) +#define JEDEC_MA_MR_WR_DDR2_2_CYC (0x1 << 9) +#define JEDEC_MA_MR_WR_DDR2_3_CYC (0x2 << 9) +#define JEDEC_MA_MR_WR_DDR2_4_CYC (0x3 << 9) +#define JEDEC_MA_MR_WR_DDR2_5_CYC (0x4 << 9) +#define JEDEC_MA_MR_WR_DDR2_6_CYC (0x5 << 9) +#define JEDEC_MA_MR_DLL_RESET (1 << 8) +#define JEDEC_MA_MR_MODE_NORMAL (0 << 8) +#define JEDEC_MA_MR_MODE_TEST (1 << 8) +#define JEDEC_MA_MR_CL_MASK (0x7 << 4) +#define JEDEC_MA_MR_CL_DDR1_2_0_CLK (0x2 << 4) +#define JEDEC_MA_MR_CL_DDR1_2_5_CLK (0x6 << 4) +#define JEDEC_MA_MR_CL_DDR1_3_0_CLK (0x3 << 4) +#define JEDEC_MA_MR_CL_DDR2_2_0_CLK (0x2 << 4) +#define JEDEC_MA_MR_CL_DDR2_3_0_CLK (0x3 << 4) +#define JEDEC_MA_MR_CL_DDR2_4_0_CLK (0x4 << 4) +#define JEDEC_MA_MR_CL_DDR2_5_0_CLK (0x5 << 4) +#define JEDEC_MA_MR_CL_DDR2_6_0_CLK (0x6 << 4) +#define JEDEC_MA_MR_CL_DDR2_7_0_CLK (0x7 << 4) +#define JEDEC_MA_MR_BTYP_SEQUENTIAL (0 << 3) +#define JEDEC_MA_MR_BTYP_INTERLEAVED (1 << 3) +#define JEDEC_MA_MR_BLEN_MASK (0x7 << 0) +#define JEDEC_MA_MR_BLEN_4 (2 << 0) +#define JEDEC_MA_MR_BLEN_8 (3 << 0) + +/* + * JEDEC DDR Extended Mode Register + */ +#define JEDEC_MA_EMR_OUTPUT_MASK (1 << 12) +#define JEDEC_MA_EMR_OUTPUT_ENABLE (0 << 12) +#define JEDEC_MA_EMR_OUTPUT_DISABLE (1 << 12) +#define JEDEC_MA_EMR_RQDS_MASK (1 << 11) +#define JEDEC_MA_EMR_RDQS_DISABLE (0 << 11) +#define JEDEC_MA_EMR_RDQS_ENABLE (1 << 11) +#define JEDEC_MA_EMR_DQS_MASK (1 << 10) +#define JEDEC_MA_EMR_DQS_DISABLE (1 << 10) +#define JEDEC_MA_EMR_DQS_ENABLE (0 << 10) +#define JEDEC_MA_EMR_OCD_MASK (0x7 << 7) +#define JEDEC_MA_EMR_OCD_EXIT (0 << 7) +#define JEDEC_MA_EMR_OCD_ENTER (7 << 7) +#define JEDEC_MA_EMR_AL_DDR1_0_CYC (0 << 3) +#define JEDEC_MA_EMR_AL_DDR2_1_CYC (1 << 3) +#define JEDEC_MA_EMR_AL_DDR2_2_CYC (2 << 3) +#define JEDEC_MA_EMR_AL_DDR2_3_CYC (3 << 3) +#define JEDEC_MA_EMR_AL_DDR2_4_CYC (4 << 3) +#define JEDEC_MA_EMR_RTT_MASK (0x11 << 2) +#define JEDEC_MA_EMR_RTT_DISABLED (0x00 << 2) +#define JEDEC_MA_EMR_RTT_75OHM (0x01 << 2) +#define JEDEC_MA_EMR_RTT_150OHM (0x10 << 2) +#define JEDEC_MA_EMR_RTT_50OHM (0x11 << 2) +#define JEDEC_MA_EMR_ODS_MASK (1 << 1) +#define JEDEC_MA_EMR_ODS_NORMAL (0 << 1) +#define JEDEC_MA_EMR_ODS_WEAK (1 << 1) +#define JEDEC_MA_EMR_DLL_MASK (1 << 0) +#define JEDEC_MA_EMR_DLL_ENABLE (0 << 0) +#define JEDEC_MA_EMR_DLL_DISABLE (1 << 0) + +/* + * JEDEC DDR Extended Mode Register 2 + */ +#define JEDEC_MA_EMR2_TEMP_COMMERCIAL (0 << 7) +#define JEDEC_MA_EMR2_TEMP_INDUSTRIAL (1 << 7) + +/* + * SDRAM Mode Register (Corresponds 1:1 w/ JEDEC Mode Register) + */ +#define SDRAM_MMODE_WR_MASK JEDEC_MA_MR_WR_MASK +#define SDRAM_MMODE_WR_DDR1 JEDEC_MA_MR_WR_DDR1 +#define SDRAM_MMODE_WR_DDR2_2_CYC JEDEC_MA_MR_WR_DDR2_2_CYC +#define SDRAM_MMODE_WR_DDR2_3_CYC JEDEC_MA_MR_WR_DDR2_3_CYC +#define SDRAM_MMODE_WR_DDR2_4_CYC JEDEC_MA_MR_WR_DDR2_4_CYC +#define SDRAM_MMODE_WR_DDR2_5_CYC JEDEC_MA_MR_WR_DDR2_5_CYC +#define SDRAM_MMODE_WR_DDR2_6_CYC JEDEC_MA_MR_WR_DDR2_6_CYC +#define SDRAM_MMODE_DCL_MASK JEDEC_MA_MR_CL_MASK +#define SDRAM_MMODE_DCL_DDR1_2_0_CLK JEDEC_MA_MR_CL_DDR1_2_0_CLK +#define SDRAM_MMODE_DCL_DDR1_2_5_CLK JEDEC_MA_MR_CL_DDR1_2_5_CLK +#define SDRAM_MMODE_DCL_DDR1_3_0_CLK JEDEC_MA_MR_CL_DDR1_3_0_CLK +#define SDRAM_MMODE_DCL_DDR2_2_0_CLK JEDEC_MA_MR_CL_DDR2_2_0_CLK +#define SDRAM_MMODE_DCL_DDR2_3_0_CLK JEDEC_MA_MR_CL_DDR2_3_0_CLK +#define SDRAM_MMODE_DCL_DDR2_4_0_CLK JEDEC_MA_MR_CL_DDR2_4_0_CLK +#define SDRAM_MMODE_DCL_DDR2_5_0_CLK JEDEC_MA_MR_CL_DDR2_5_0_CLK +#define SDRAM_MMODE_DCL_DDR2_6_0_CLK JEDEC_MA_MR_CL_DDR2_6_0_CLK +#define SDRAM_MMODE_DCL_DDR2_7_0_CLK JEDEC_MA_MR_CL_DDR2_7_0_CLK +#define SDRAM_MMODE_BTYP_SEQUENTIAL JEDEC_MA_MR_BTYP_SEQUENTIAL +#define SDRAM_MMODE_BTYP_INTERLEAVED JEDEC_MA_MR_BTYP_INTERLEAVED +#define SDRAM_MMODE_BLEN_MASK JEDEC_MA_MR_BLEN_MASK +#define SDRAM_MMODE_BLEN_4 JEDEC_MA_MR_BLEN_4 +#define SDRAM_MMODE_BLEN_8 JEDEC_MA_MR_BLEN_8 + +/* + * SDRAM Extended Mode Register (Corresponds 1:1 w/ JEDEC Extended + * Mode Register) + */ +#define SDRAM_MEMODE_QOFF_MASK JEDEC_MA_EMR_OUTPUT_MASK +#define SDRAM_MEMODE_QOFF_DISABLE JEDEC_MA_EMR_OUTPUT_DISABLE +#define SDRAM_MEMODE_QOFF_ENABLE JEDEC_MA_EMR_OUTPUT_ENABLE +#define SDRAM_MEMODE_RDQS_MASK JEDEC_MA_EMR_RQDS_MASK +#define SDRAM_MEMODE_RDQS_DISABLE JEDEC_MA_EMR_RDQS_DISABLE +#define SDRAM_MEMODE_RDQS_ENABLE JEDEC_MA_EMR_RDQS_ENABLE +#define SDRAM_MEMODE_DQS_MASK JEDEC_MA_EMR_DQS_MASK +#define SDRAM_MEMODE_DQS_DISABLE JEDEC_MA_EMR_DQS_DISABLE +#define SDRAM_MEMODE_DQS_ENABLE JEDEC_MA_EMR_DQS_ENABLE +#define SDRAM_MEMODE_AL_DDR1_0_CYC JEDEC_MA_EMR_AL_DDR1_0_CYC +#define SDRAM_MEMODE_AL_DDR2_1_CYC JEDEC_MA_EMR_AL_DDR2_1_CYC +#define SDRAM_MEMODE_AL_DDR2_2_CYC JEDEC_MA_EMR_AL_DDR2_2_CYC +#define SDRAM_MEMODE_AL_DDR2_3_CYC JEDEC_MA_EMR_AL_DDR2_3_CYC +#define SDRAM_MEMODE_AL_DDR2_4_CYC JEDEC_MA_EMR_AL_DDR2_4_CYC +#define SDRAM_MEMODE_RTT_MASK JEDEC_MA_EMR_RTT_MASK +#define SDRAM_MEMODE_RTT_DISABLED JEDEC_MA_EMR_RTT_DISABLED +#define SDRAM_MEMODE_RTT_75OHM JEDEC_MA_EMR_RTT_75OHM +#define SDRAM_MEMODE_RTT_150OHM JEDEC_MA_EMR_RTT_150OHM +#define SDRAM_MEMODE_RTT_50OHM JEDEC_MA_EMR_RTT_50OHM +#define SDRAM_MEMODE_DIC_MASK JEDEC_MA_EMR_ODS_MASK +#define SDRAM_MEMODE_DIC_NORMAL JEDEC_MA_EMR_ODS_NORMAL +#define SDRAM_MEMODE_DIC_WEAK JEDEC_MA_EMR_ODS_WEAK +#define SDRAM_MEMODE_DLL_MASK JEDEC_MA_EMR_DLL_MASK +#define SDRAM_MEMODE_DLL_DISABLE JEDEC_MA_EMR_DLL_DISABLE +#define SDRAM_MEMODE_DLL_ENABLE JEDEC_MA_EMR_DLL_ENABLE /* * SDRAM Clock Timing Register @@ -684,6 +898,24 @@ #define SDRAM_SDTR3_RFC_ENCODE(n) ((((u32)(n))&0x3F)<<0) /* + * ECC Error Status + */ +#define SDRAM_ECCES_MASK PPC_REG_VAL(21, 0x3FFFFF) +#define SDRAM_ECCES_BNCE_MASK PPC_REG_VAL(15, 0xFFFF) +#define SDRAM_ECCES_BNCE_ENCODE(lane) PPC_REG_VAL(((lane) & 0xF), 1) +#define SDRAM_ECCES_CKBER_MASK PPC_REG_VAL(17, 0x3) +#define SDRAM_ECCES_CKBER_NONE PPC_REG_VAL(17, 0) +#define SDRAM_ECCES_CKBER_16_ECC_0_3 PPC_REG_VAL(17, 2) +#define SDRAM_ECCES_CKBER_32_ECC_0_3 PPC_REG_VAL(17, 1) +#define SDRAM_ECCES_CKBER_32_ECC_4_8 PPC_REG_VAL(17, 2) +#define SDRAM_ECCES_CKBER_32_ECC_0_8 PPC_REG_VAL(17, 3) +#define SDRAM_ECCES_CE PPC_REG_VAL(18, 1) +#define SDRAM_ECCES_UE PPC_REG_VAL(19, 1) +#define SDRAM_ECCES_BKNER_MASK PPC_REG_VAL(21, 0x3) +#define SDRAM_ECCES_BK0ER PPC_REG_VAL(20, 1) +#define SDRAM_ECCES_BK1ER PPC_REG_VAL(21, 1) + +/* * Memory Bank 0-1 configuration */ #define SDRAM_BXCF_M_AM_MASK 0x00000F00 /* Addressing mode */ diff --git a/include/asm-ppc/ppc4xx-uic.h b/include/asm-ppc/ppc4xx-uic.h new file mode 100644 index 0000000..d50c363 --- /dev/null +++ b/include/asm-ppc/ppc4xx-uic.h @@ -0,0 +1,314 @@ +/* + * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com> + * + * (C) Copyright 2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _PPC4xx_UIC_H_ +#define _PPC4xx_UIC_H_ + +/* + * Define the number of UIC's + */ +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) +#define UIC_MAX 4 +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) +#define UIC_MAX 3 +#elif defined(CONFIG_440GP) || defined(CONFIG_440SP) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) +#define UIC_MAX 2 +#else +#define UIC_MAX 1 +#endif + +/* + * UIC register + */ +#define UIC_SR 0x0 /* UIC status */ +#define UIC_ER 0x2 /* UIC enable */ +#define UIC_CR 0x3 /* UIC critical */ +#define UIC_PR 0x4 /* UIC polarity */ +#define UIC_TR 0x5 /* UIC triggering */ +#define UIC_MSR 0x6 /* UIC masked status */ +#define UIC_VR 0x7 /* UIC vector */ +#define UIC_VCR 0x8 /* UIC vector configuration */ + +/* + * On 440GX we use the UICB0 as UIC0. Its the root UIC where all other UIC's + * are cascaded on. With this trick we can use the common UIC code for 440GX + * too. + */ +#if defined(CONFIG_440GX) +#define UIC0_DCR_BASE 0x200 +#define UIC1_DCR_BASE 0xc0 +#define UIC2_DCR_BASE 0xd0 +#define UIC3_DCR_BASE 0x210 +#else +#define UIC0_DCR_BASE 0xc0 +#define UIC1_DCR_BASE 0xd0 +#define UIC2_DCR_BASE 0xe0 +#define UIC3_DCR_BASE 0xf0 +#endif + +#define uic0sr (UIC0_DCR_BASE+0x0) /* UIC0 status */ +#define uic0er (UIC0_DCR_BASE+0x2) /* UIC0 enable */ +#define uic0cr (UIC0_DCR_BASE+0x3) /* UIC0 critical */ +#define uic0pr (UIC0_DCR_BASE+0x4) /* UIC0 polarity */ +#define uic0tr (UIC0_DCR_BASE+0x5) /* UIC0 triggering */ +#define uic0msr (UIC0_DCR_BASE+0x6) /* UIC0 masked status */ +#define uic0vr (UIC0_DCR_BASE+0x7) /* UIC0 vector */ +#define uic0vcr (UIC0_DCR_BASE+0x8) /* UIC0 vector configuration */ + +#define uic1sr (UIC1_DCR_BASE+0x0) /* UIC1 status */ +#define uic1er (UIC1_DCR_BASE+0x2) /* UIC1 enable */ +#define uic1cr (UIC1_DCR_BASE+0x3) /* UIC1 critical */ +#define uic1pr (UIC1_DCR_BASE+0x4) /* UIC1 polarity */ +#define uic1tr (UIC1_DCR_BASE+0x5) /* UIC1 triggering */ +#define uic1msr (UIC1_DCR_BASE+0x6) /* UIC1 masked status */ +#define uic1vr (UIC1_DCR_BASE+0x7) /* UIC1 vector */ +#define uic1vcr (UIC1_DCR_BASE+0x8) /* UIC1 vector configuration */ + +#define uic2sr (UIC2_DCR_BASE+0x0) /* UIC2 status-Read Clear */ +#define uic2srs (UIC2_DCR_BASE+0x1) /* UIC2 status-Read Set */ +#define uic2er (UIC2_DCR_BASE+0x2) /* UIC2 enable */ +#define uic2cr (UIC2_DCR_BASE+0x3) /* UIC2 critical */ +#define uic2pr (UIC2_DCR_BASE+0x4) /* UIC2 polarity */ +#define uic2tr (UIC2_DCR_BASE+0x5) /* UIC2 triggering */ +#define uic2msr (UIC2_DCR_BASE+0x6) /* UIC2 masked status */ +#define uic2vr (UIC2_DCR_BASE+0x7) /* UIC2 vector */ +#define uic2vcr (UIC2_DCR_BASE+0x8) /* UIC2 vector configuration */ + +#define uic3sr (UIC3_DCR_BASE+0x0) /* UIC3 status-Read Clear */ +#define uic3srs (UIC3_DCR_BASE+0x1) /* UIC3 status-Read Set */ +#define uic3er (UIC3_DCR_BASE+0x2) /* UIC3 enable */ +#define uic3cr (UIC3_DCR_BASE+0x3) /* UIC3 critical */ +#define uic3pr (UIC3_DCR_BASE+0x4) /* UIC3 polarity */ +#define uic3tr (UIC3_DCR_BASE+0x5) /* UIC3 triggering */ +#define uic3msr (UIC3_DCR_BASE+0x6) /* UIC3 masked status */ +#define uic3vr (UIC3_DCR_BASE+0x7) /* UIC3 vector */ +#define uic3vcr (UIC3_DCR_BASE+0x8) /* UIC3 vector configuration */ + +/* The following is for compatibility with 405 code */ +#define uicsr uic0sr +#define uicer uic0er +#define uiccr uic0cr +#define uicpr uic0pr +#define uictr uic0tr +#define uicmsr uic0msr +#define uicvr uic0vr +#define uicvcr uic0vcr + +/* + * Now the interrupt vector definitions. They are different for most of + * the 4xx variants, so we need some more #ifdef's here. No mask + * definitions anymore here. For this please use the UIC_MASK macro below. + * + * Note: Please only define the interrupts really used in U-Boot here. + * Those are the cascading and EMAC/MAL related interrupt. + */ + +#if defined(CONFIG_405EP) || defined(CONFIG_405GP) +#define VECNUM_MAL_SERR 10 +#define VECNUM_MAL_TXEOB 11 +#define VECNUM_MAL_RXEOB 12 +#define VECNUM_MAL_TXDE 13 +#define VECNUM_MAL_RXDE 14 +#define VECNUM_ETH0 15 +#define VECNUM_ETH1_OFFS 2 +#define VECNUM_EIRQ6 29 +#endif /* defined(CONFIG_405EP) */ + +#if defined(CONFIG_405EZ) +#define VECNUM_USBDEV 15 +#define VECNUM_ETH0 16 +#define VECNUM_MAL_SERR 18 +#define VECNUM_MAL_TXDE 18 +#define VECNUM_MAL_RXDE 18 +#define VECNUM_MAL_TXEOB 19 +#define VECNUM_MAL_RXEOB 21 +#endif /* CONFIG_405EX */ + +#if defined(CONFIG_405EX) +/* UIC 0 */ +#define VECNUM_MAL_TXEOB 10 +#define VECNUM_MAL_RXEOB 11 +#define VECNUM_ETH0 24 +#define VECNUM_ETH1_OFFS 1 +#define VECNUM_UIC2NCI 28 +#define VECNUM_UIC2CI 29 +#define VECNUM_UIC1NCI 30 +#define VECNUM_UIC1CI 31 + +/* UIC 1 */ +#define VECNUM_MAL_SERR (32 + 0) +#define VECNUM_MAL_TXDE (32 + 1) +#define VECNUM_MAL_RXDE (32 + 2) +#endif /* CONFIG_405EX */ + +#if defined(CONFIG_440GP) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) +/* UIC 0 */ +#define VECNUM_MAL_TXEOB 10 +#define VECNUM_MAL_RXEOB 11 +#define VECNUM_UIC1NCI 30 +#define VECNUM_UIC1CI 31 + +/* UIC 1 */ +#define VECNUM_MAL_SERR (32 + 0) +#define VECNUM_MAL_TXDE (32 + 1) +#define VECNUM_MAL_RXDE (32 + 2) +#define VECNUM_USBDEV (32 + 23) +#define VECNUM_ETH0 (32 + 28) +#define VECNUM_ETH1_OFFS 2 +#endif /* CONFIG_440GP */ + +#if defined(CONFIG_440GX) +/* UICB 0 (440GX only) */ +/* + * All those defines below are off-by-one, so that the common UIC code + * can be used. So VECNUM_UIC1CI refers to VECNUM_UIC0CI etc. + */ +#define VECNUM_UIC1CI 0 +#define VECNUM_UIC1NCI 1 +#define VECNUM_UIC2CI 2 +#define VECNUM_UIC2NCI 3 +#define VECNUM_UIC3CI 4 +#define VECNUM_UIC3NCI 5 + +/* UIC 0, used as UIC1 on 440GX because of UICB0 */ +#define VECNUM_MAL_TXEOB (32 + 10) +#define VECNUM_MAL_RXEOB (32 + 11) + +/* UIC 1, used as UIC2 on 440GX because of UICB0 */ +#define VECNUM_MAL_SERR (64 + 0) +#define VECNUM_MAL_TXDE (64 + 1) +#define VECNUM_MAL_RXDE (64 + 2) +#define VECNUM_ETH0 (64 + 28) +#define VECNUM_ETH1_OFFS 2 +#endif /* CONFIG_440GX */ + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +/* UIC 0 */ +#define VECNUM_MAL_TXEOB 10 +#define VECNUM_MAL_RXEOB 11 +#define VECNUM_USBDEV 20 +#define VECNUM_ETH0 24 +#define VECNUM_ETH1_OFFS 1 +#define VECNUM_UIC2NCI 28 +#define VECNUM_UIC2CI 29 +#define VECNUM_UIC1NCI 30 +#define VECNUM_UIC1CI 31 + +/* UIC 1 */ +#define VECNUM_MAL_SERR (32 + 0) +#define VECNUM_MAL_TXDE (32 + 1) +#define VECNUM_MAL_RXDE (32 + 2) + +/* UIC 2 */ +#define VECNUM_EIRQ2 (64 + 3) +#endif /* CONFIG_440EPX */ + +#if defined(CONFIG_440SP) +/* UIC 0 */ +#define VECNUM_UIC1NCI 30 +#define VECNUM_UIC1CI 31 + +/* UIC 1 */ +#define VECNUM_MAL_SERR (32 + 1) +#define VECNUM_MAL_TXDE (32 + 2) +#define VECNUM_MAL_RXDE (32 + 3) +#define VECNUM_MAL_TXEOB (32 + 6) +#define VECNUM_MAL_RXEOB (32 + 7) +#define VECNUM_ETH0 (32 + 28) +#endif /* CONFIG_440SP */ + +#if defined(CONFIG_440SPE) +/* UIC 0 */ +#define VECNUM_UIC2NCI 10 +#define VECNUM_UIC2CI 11 +#define VECNUM_UIC3NCI 16 +#define VECNUM_UIC3CI 17 +#define VECNUM_UIC1NCI 30 +#define VECNUM_UIC1CI 31 + +/* UIC 1 */ +#define VECNUM_MAL_SERR (32 + 1) +#define VECNUM_MAL_TXDE (32 + 2) +#define VECNUM_MAL_RXDE (32 + 3) +#define VECNUM_MAL_TXEOB (32 + 6) +#define VECNUM_MAL_RXEOB (32 + 7) +#define VECNUM_ETH0 (32 + 28) +#endif /* CONFIG_440SPE */ + +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +/* UIC 0 */ +#define VECNUM_UIC2NCI 10 +#define VECNUM_UIC2CI 11 +#define VECNUM_UIC3NCI 16 +#define VECNUM_UIC3CI 17 +#define VECNUM_UIC1NCI 30 +#define VECNUM_UIC1CI 31 + +/* UIC 2 */ +#define VECNUM_MAL_SERR (64 + 3) +#define VECNUM_MAL_TXDE (64 + 4) +#define VECNUM_MAL_RXDE (64 + 5) +#define VECNUM_MAL_TXEOB (64 + 6) +#define VECNUM_MAL_RXEOB (64 + 7) +#define VECNUM_ETH0 (64 + 16) +#define VECNUM_ETH1_OFFS 1 +#endif /* CONFIG_460EX */ + +#if defined(CONFIG_460SX) +/* UIC 0 */ +#define VECNUM_UIC2NCI 10 +#define VECNUM_UIC2CI 11 +#define VECNUM_UIC3NCI 16 +#define VECNUM_UIC3CI 17 +#define VECNUM_ETH0 19 +#define VECNUM_ETH1_OFFS 1 +#define VECNUM_UIC1NCI 30 +#define VECNUM_UIC1CI 31 + +/* UIC 1 */ +#define VECNUM_MAL_SERR (32 + 1) +#define VECNUM_MAL_TXDE (32 + 2) +#define VECNUM_MAL_RXDE (32 + 3) +#define VECNUM_MAL_TXEOB (32 + 6) +#define VECNUM_MAL_RXEOB (32 + 7) +#endif /* CONFIG_460EX */ + +#if !defined(VECNUM_ETH1_OFFS) +#define VECNUM_ETH1_OFFS 1 +#endif + +/* + * Mask definitions (used for example in 4xx_enet.c) + */ +#define UIC_MASK(vec) (0x80000000 >> ((vec) & 0x1f)) +/* UIC_NR won't work for 440GX because of its specific UIC DCR addresses */ +#define UIC_NR(vec) ((vec) >> 5) + +#endif /* _PPC4xx_UIC_H_ */ diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index e617868..b214844 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -830,6 +830,10 @@ #define PVR_460EX_RA 0x130218A3 /* 460EX rev A without Security Engine */ #define PVR_460GT_SE_RA 0x130218A0 /* 460GT rev A with Security Engine */ #define PVR_460GT_RA 0x130218A1 /* 460GT rev A without Security Engine */ +#define PVR_460SX_RA 0x13541800 /* 460SX rev A */ +#define PVR_460SX_RA_V1 0x13541801 /* 460SX rev A Variant 1 Security disabled */ +#define PVR_460GX_RA 0x13541802 /* 460GX rev A */ +#define PVR_460GX_RA_V1 0x13541803 /* 460GX rev A Variant 1 Security disabled */ #define PVR_601 0x00010000 #define PVR_602 0x00050000 #define PVR_603 0x00030000 diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 8ea1ac3..9bcbfe3 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -407,7 +407,7 @@ /* * define UIC_EXT0 ... UIC_EXT6 if external interrupt is active high */ -#define CFG_UIC0_POLARITY (0xFFFFFF80 | UIC_EXT6) +#define CFG_UIC0_POLARITY (0xFFFFFF80 | UIC_MASK(VECNUM_EIRQ6)) /*----------------------------------------------------------------------- * FPGA stuff diff --git a/include/configs/katmai.h b/include/configs/katmai.h index f07e470..047ec9e 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -54,7 +54,6 @@ #include "amcc-common.h" #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ #undef CONFIG_SHOW_BOOT_PROGRESS /*----------------------------------------------------------------------- diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 9c1a3a4..dc246fd 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -233,39 +233,124 @@ #define CFG_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE #define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE #define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE -#define CFG_SDRAM0_MCOPT1 0x04322000 +#define CFG_SDRAM0_MCOPT1 (SDRAM_MCOPT1_PMU_OPEN | \ + SDRAM_MCOPT1_8_BANKS | \ + SDRAM_MCOPT1_DDR2_TYPE | \ + SDRAM_MCOPT1_QDEP | \ + SDRAM_MCOPT1_DCOO_DISABLED) #define CFG_SDRAM0_MCOPT2 0x00000000 -#define CFG_SDRAM0_MODT0 0x01800000 +#define CFG_SDRAM0_MODT0 (SDRAM_MODT_EB0W_ENABLE | \ + SDRAM_MODT_EB0R_ENABLE) #define CFG_SDRAM0_MODT1 0x00000000 -#define CFG_SDRAM0_CODT 0x0080f837 -#define CFG_SDRAM0_RTR 0x06180000 -#define CFG_SDRAM0_INITPLR0 0xa8380000 -#define CFG_SDRAM0_INITPLR1 0x81900400 -#define CFG_SDRAM0_INITPLR2 0x81020000 -#define CFG_SDRAM0_INITPLR3 0x81030000 -#define CFG_SDRAM0_INITPLR4 0x81010404 -#define CFG_SDRAM0_INITPLR5 0x81000542 -#define CFG_SDRAM0_INITPLR6 0x81900400 -#define CFG_SDRAM0_INITPLR7 0x8D080000 -#define CFG_SDRAM0_INITPLR8 0x8D080000 -#define CFG_SDRAM0_INITPLR9 0x8D080000 -#define CFG_SDRAM0_INITPLR10 0x8D080000 -#define CFG_SDRAM0_INITPLR11 0x81000442 -#define CFG_SDRAM0_INITPLR12 0x81010780 -#define CFG_SDRAM0_INITPLR13 0x81010400 -#define CFG_SDRAM0_INITPLR14 0x00000000 -#define CFG_SDRAM0_INITPLR15 0x00000000 -#define CFG_SDRAM0_RQDC 0x80000038 -#define CFG_SDRAM0_RFDC 0x00000209 -#define CFG_SDRAM0_RDCC 0x40000000 -#define CFG_SDRAM0_DLCR 0x030000a5 -#define CFG_SDRAM0_CLKTR 0x80000000 +#define CFG_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \ + SDRAM_CODT_CKLZ_36OHM | \ + SDRAM_CODT_DQS_1_8_V_DDR2 | \ + SDRAM_CODT_IO_NMODE) +#define CFG_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560) +#define CFG_SDRAM0_INITPLR0 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(80) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP)) +#define CFG_SDRAM0_INITPLR1 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(3) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL)) +#define CFG_SDRAM0_INITPLR2 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(2) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL)) +#define CFG_SDRAM0_INITPLR3 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(2) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3) | \ + SDRAM_INITPLR_IMA_ENCODE(0)) +#define CFG_SDRAM0_INITPLR4 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(2) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_DISABLE | \ + JEDEC_MA_EMR_RTT_75OHM)) +#define CFG_SDRAM0_INITPLR5 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(2) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \ + JEDEC_MA_MR_CL_DDR2_4_0_CLK | \ + JEDEC_MA_MR_BLEN_4 | \ + JEDEC_MA_MR_DLL_RESET)) +#define CFG_SDRAM0_INITPLR6 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(3) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \ + SDRAM_INITPLR_IBA_ENCODE(0x0) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL)) +#define CFG_SDRAM0_INITPLR7 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(26) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) +#define CFG_SDRAM0_INITPLR8 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(26) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) +#define CFG_SDRAM0_INITPLR9 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(26) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) +#define CFG_SDRAM0_INITPLR10 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(26) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) +#define CFG_SDRAM0_INITPLR11 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(2) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \ + JEDEC_MA_MR_CL_DDR2_4_0_CLK | \ + JEDEC_MA_MR_BLEN_4)) +#define CFG_SDRAM0_INITPLR12 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(2) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_ENTER | \ + JEDEC_MA_EMR_RDQS_DISABLE | \ + JEDEC_MA_EMR_DQS_DISABLE | \ + JEDEC_MA_EMR_RTT_DISABLED | \ + JEDEC_MA_EMR_ODS_NORMAL)) +#define CFG_SDRAM0_INITPLR13 (SDRAM_INITPLR_ENABLE | \ + SDRAM_INITPLR_IMWT_ENCODE(2) | \ + SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ + SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ + SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_EXIT | \ + JEDEC_MA_EMR_RDQS_DISABLE | \ + JEDEC_MA_EMR_DQS_DISABLE | \ + JEDEC_MA_EMR_RTT_DISABLED | \ + JEDEC_MA_EMR_ODS_NORMAL)) +#define CFG_SDRAM0_INITPLR14 (SDRAM_INITPLR_DISABLE) +#define CFG_SDRAM0_INITPLR15 (SDRAM_INITPLR_DISABLE) +#define CFG_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \ + SDRAM_RQDC_RQFD_ENCODE(56)) +#define CFG_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(521) +#define CFG_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2) +#define CFG_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \ + SDRAM_DLCR_DLCS_CONT_DONE | \ + SDRAM_DLCR_DLCV_ENCODE(165)) +#define CFG_SDRAM0_CLKTR (SDRAM_CLKTR_CLKP_180_DEG_ADV) #define CFG_SDRAM0_WRDTR 0x00000000 -#define CFG_SDRAM0_SDTR1 0x80201000 -#define CFG_SDRAM0_SDTR2 0x32204232 -#define CFG_SDRAM0_SDTR3 0x080b0d1a -#define CFG_SDRAM0_MMODE 0x00000442 -#define CFG_SDRAM0_MEMODE 0x00000404 +#define CFG_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \ + SDRAM_SDTR1_RTW_2_CLK | \ + SDRAM_SDTR1_RTRO_1_CLK) +#define CFG_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \ + SDRAM_SDTR2_WTR_2_CLK | \ + SDRAM_SDTR2_XSNR_32_CLK | \ + SDRAM_SDTR2_WPC_4_CLK | \ + SDRAM_SDTR2_RPC_2_CLK | \ + SDRAM_SDTR2_RP_3_CLK | \ + SDRAM_SDTR2_RRD_2_CLK) +#define CFG_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \ + SDRAM_SDTR3_RC_ENCODE(11) | \ + SDRAM_SDTR3_XCS | \ + SDRAM_SDTR3_RFC_ENCODE(26)) +#define CFG_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \ + SDRAM_MMODE_DCL_DDR2_4_0_CLK | \ + SDRAM_MMODE_BLEN_4) +#define CFG_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_DISABLE | \ + SDRAM_MEMODE_RTT_75OHM) /*----------------------------------------------------------------------- * I2C @@ -290,6 +375,7 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 65b240e..ab92ae4 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -223,6 +223,7 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII #define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ diff --git a/include/configs/redwood.h b/include/configs/redwood.h new file mode 100644 index 0000000..32ed574 --- /dev/null +++ b/include/configs/redwood.h @@ -0,0 +1,186 @@ +/* + * Configuration for AMCC 460SX Ref (redwood) + * + * (C) Copyright 2008 + * Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_440 1 /* ... PPC460 family */ +#define CONFIG_460SX 1 /* ... PPC460 family */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +/*----------------------------------------------------------------------- + * Include common defines/options for all AMCC boards + *----------------------------------------------------------------------*/ +#define CONFIG_HOSTNAME redwood + +#include "amcc-common.h" + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ +#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ +#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ + +#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ + +#define CFG_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ +#define CFG_PCIE0_MEMBASE 0x90000000 /* mapped PCIe memory */ +#define CFG_PCIE1_MEMBASE 0xa0000000 /* mapped PCIe memory */ +#define CFG_PCIE_MEMSIZE 0x01000000 + +#define CFG_PCIE0_XCFGBASE 0xb0000000 +#define CFG_PCIE1_XCFGBASE 0xb2000000 +#define CFG_PCIE2_XCFGBASE 0xb4000000 +#define CFG_PCIE0_CFGBASE 0xb6000000 +#define CFG_PCIE1_CFGBASE 0xb8000000 +#define CFG_PCIE2_CFGBASE 0xba000000 + +/* PCIe mapped UTL registers */ +#define CFG_PCIE0_REGBASE 0xd0000000 +#define CFG_PCIE1_REGBASE 0xd0010000 +#define CFG_PCIE2_REGBASE 0xd0020000 + +/* System RAM mapped to PCI space */ +#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024) + +#define CFG_FPGA_BASE 0xe2000000 /* epld */ +#define CFG_OPER_FLASH 0xe7000000 /* SRAM - OPER Flash */ + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in internal SRAM) + *----------------------------------------------------------------------*/ +#define CFG_TEMP_STACK_OCM 1 +#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE +#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ + +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ +#define CONFIG_DDR_ECC 1 /* with ECC support */ + +#define CFG_SPD_MAX_DIMMS 2 + +/* SPD i2c spd addresses */ +#define SPD_EEPROM_ADDRESS {IIC0_DIMM0_ADDR, IIC0_DIMM1_ADDR} +#define IIC0_DIMM0_ADDR 0x53 +#define IIC0_DIMM1_ADDR 0x52 + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CFG_I2C_SPEED 400000 /* I2C speed */ + +#define IIC0_BOOTPROM_ADDR 0x50 +#define IIC0_ALT_BOOTPROM_ADDR 0x54 + +/* Don't probe these addrs */ +#define CFG_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54} + +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#undef CFG_ENV_IS_IN_NVRAM /* ... not in NVRAM */ +#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ +#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ + "kernel_addr=fc000000\0" \ + "fdt_addr=fc1e0000\0" \ + "ramdisk_addr=fc200000\0" \ + "" + +/*----------------------------------------------------------------------------+ +| Commands in addition to amcc-common.h ++----------------------------------------------------------------------------*/ +#define CONFIG_CMD_SDRAM + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 1000 +#define CONFIG_M88E1141_PHY 1 /* Enable phy */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ +#define CONFIG_PHY1_ADDR 1 /* PHY address, See schematics */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CFG_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */ + +#define CFG_MAX_FLASH_BANKS 3 /* number of banks */ +#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CFG_ENV_ADDR 0xfffa0000 +#define CFG_ENV_SIZE 0x10000 /* Size of Environment vars */ +#endif /* CFG_ENV_IS_IN_FLASH */ + +/*---------------------------------------------------------------------------*/ + +#endif /* __CONFIG_H */ diff --git a/include/ppc405.h b/include/ppc405.h index 2231a5f..f19b67f 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -119,367 +119,6 @@ #define dmasgc (DMA_DCR_BASE+0x23) /* DMA scatter/gather command register */ #define dmaadr (DMA_DCR_BASE+0x24) /* DMA address decode register */ -/****************************************************************************** - * Universal interrupt controller - ******************************************************************************/ -#define UIC_SR 0x0 /* UIC status */ -#define UIC_ER 0x2 /* UIC enable */ -#define UIC_CR 0x3 /* UIC critical */ -#define UIC_PR 0x4 /* UIC polarity */ -#define UIC_TR 0x5 /* UIC triggering */ -#define UIC_MSR 0x6 /* UIC masked status */ -#define UIC_VR 0x7 /* UIC vector */ -#define UIC_VCR 0x8 /* UIC vector configuration */ - -#define UIC_DCR_BASE 0xc0 -#define UIC0_DCR_BASE UIC_DCR_BASE -#define uicsr (UIC_DCR_BASE+0x0) /* UIC status */ -#define uicsrs (UIC_DCR_BASE+0x1) /* UIC status set */ -#define uicer (UIC_DCR_BASE+0x2) /* UIC enable */ -#define uiccr (UIC_DCR_BASE+0x3) /* UIC critical */ -#define uicpr (UIC_DCR_BASE+0x4) /* UIC polarity */ -#define uictr (UIC_DCR_BASE+0x5) /* UIC triggering */ -#define uicmsr (UIC_DCR_BASE+0x6) /* UIC masked status */ -#define uicvr (UIC_DCR_BASE+0x7) /* UIC vector */ -#define uicvcr (UIC_DCR_BASE+0x8) /* UIC vector configuration */ - -#if defined(CONFIG_405EX) -#define uic0sr uicsr /* UIC status */ -#define uic0srs uicsrs /* UIC status set */ -#define uic0er uicer /* UIC enable */ -#define uic0cr uiccr /* UIC critical */ -#define uic0pr uicpr /* UIC polarity */ -#define uic0tr uictr /* UIC triggering */ -#define uic0msr uicmsr /* UIC masked status */ -#define uic0vr uicvr /* UIC vector */ -#define uic0vcr uicvcr /* UIC vector configuration*/ - -#define UIC_DCR_BASE1 0xd0 -#define UIC1_DCR_BASE 0xd0 -#define uic1sr (UIC_DCR_BASE1+0x0) /* UIC status */ -#define uic1srs (UIC_DCR_BASE1+0x1) /* UIC status set */ -#define uic1er (UIC_DCR_BASE1+0x2) /* UIC enable */ -#define uic1cr (UIC_DCR_BASE1+0x3) /* UIC critical */ -#define uic1pr (UIC_DCR_BASE1+0x4) /* UIC polarity */ -#define uic1tr (UIC_DCR_BASE1+0x5) /* UIC triggering */ -#define uic1msr (UIC_DCR_BASE1+0x6) /* UIC masked status */ -#define uic1vr (UIC_DCR_BASE1+0x7) /* UIC vector */ -#define uic1vcr (UIC_DCR_BASE1+0x8) /* UIC vector configuration*/ - -#define UIC_DCR_BASE2 0xe0 -#define UIC2_DCR_BASE 0xe0 -#define uic2sr (UIC_DCR_BASE2+0x0) /* UIC status */ -#define uic2srs (UIC_DCR_BASE2+0x1) /* UIC status set */ -#define uic2er (UIC_DCR_BASE2+0x2) /* UIC enable */ -#define uic2cr (UIC_DCR_BASE2+0x3) /* UIC critical */ -#define uic2pr (UIC_DCR_BASE2+0x4) /* UIC polarity */ -#define uic2tr (UIC_DCR_BASE2+0x5) /* UIC triggering */ -#define uic2msr (UIC_DCR_BASE2+0x6) /* UIC masked status */ -#define uic2vr (UIC_DCR_BASE2+0x7) /* UIC vector */ -#define uic2vcr (UIC_DCR_BASE2+0x8) /* UIC vector configuration*/ -#endif - -/*-----------------------------------------------------------------------------+ -| Universal interrupt controller interrupts -+-----------------------------------------------------------------------------*/ -#if defined(CONFIG_405EZ) -#define UIC_DMA0 0x80000000 /* DMA chan. 0 */ -#define UIC_DMA1 0x40000000 /* DMA chan. 1 */ -#define UIC_DMA2 0x20000000 /* DMA chan. 2 */ -#define UIC_DMA3 0x10000000 /* DMA chan. 3 */ -#define UIC_1588 0x08000000 /* IEEE 1588 network synchronization */ -#define UIC_UART0 0x04000000 /* UART 0 */ -#define UIC_UART1 0x02000000 /* UART 1 */ -#define UIC_CAN0 0x01000000 /* CAN 0 */ -#define UIC_CAN1 0x00800000 /* CAN 1 */ -#define UIC_SPI 0x00400000 /* SPI */ -#define UIC_IIC 0x00200000 /* IIC */ -#define UIC_CHT0 0x00100000 /* Chameleon timer high pri interrupt */ -#define UIC_CHT1 0x00080000 /* Chameleon timer high pri interrupt */ -#define UIC_USBH1 0x00040000 /* USB Host 1 */ -#define UIC_USBH2 0x00020000 /* USB Host 2 */ -#define UIC_USBDEV 0x00010000 /* USB Device */ -#define UIC_ENET 0x00008000 /* Ethernet interrupt status */ -#define UIC_ENET1 0x00008000 /* dummy define */ -#define UIC_EMAC_WAKE 0x00004000 /* EMAC wake up */ - -#define UIC_MADMAL 0x00002000 /* Logical OR of following MadMAL int */ -#define UIC_MAL_SERR 0x00002000 /* MAL SERR */ -#define UIC_MAL_TXDE 0x00002000 /* MAL TXDE */ -#define UIC_MAL_RXDE 0x00002000 /* MAL RXDE */ - -#define UIC_MAL_TXEOB 0x00001000 /* MAL TXEOB */ -#define UIC_MAL_TXEOB1 0x00000800 /* MAL TXEOB1 */ -#define UIC_MAL_RXEOB 0x00000400 /* MAL RXEOB */ -#define UIC_NAND 0x00000200 /* NAND Flash controller */ -#define UIC_ADC 0x00000100 /* ADC */ -#define UIC_DAC 0x00000080 /* DAC */ -#define UIC_OPB2PLB 0x00000040 /* OPB to PLB bridge interrupt */ -#define UIC_RESERVED0 0x00000020 /* Reserved */ -#define UIC_EXT0 0x00000010 /* External interrupt 0 */ -#define UIC_EXT1 0x00000008 /* External interrupt 1 */ -#define UIC_EXT2 0x00000004 /* External interrupt 2 */ -#define UIC_EXT3 0x00000002 /* External interrupt 3 */ -#define UIC_EXT4 0x00000001 /* External interrupt 4 */ - -#elif defined(CONFIG_405EX) - -/* UIC 0 */ -#define UIC_U0 0x80000000 /* */ -#define UIC_U1 0x40000000 /* */ -#define UIC_IIC0 0x20000000 /* */ -#define UIC_PKA 0x10000000 /* */ -#define UIC_TRNG 0x08000000 /* */ -#define UIC_EBM 0x04000000 /* */ -#define UIC_BGI 0x02000000 /* */ -#define UIC_IIC1 0x01000000 /* */ -#define UIC_SPI 0x00800000 /* */ -#define UIC_EIRQ0 0x00400000 /**/ -#define UIC_MTE 0x00200000 /*MAL Tx EOB */ -#define UIC_MRE 0x00100000 /*MAL Rx EOB */ -#define UIC_DMA0 0x00080000 /* */ -#define UIC_DMA1 0x00040000 /* */ -#define UIC_DMA2 0x00020000 /* */ -#define UIC_DMA3 0x00010000 /* */ -#define UIC_PCIE0AL 0x00008000 /* */ -#define UIC_PCIE0VPD 0x00004000 /* */ -#define UIC_RPCIE0HRST 0x00002000 /* */ -#define UIC_FPCIE0HRST 0x00001000 /* */ -#define UIC_PCIE0TCR 0x00000800 /* */ -#define UIC_PCIEMSI0 0x00000400 /* */ -#define UIC_PCIEMSI1 0x00000200 /* */ -#define UIC_SECURITY 0x00000100 /* */ -#define UIC_ENET 0x00000080 /* */ -#define UIC_ENET1 0x00000040 /* */ -#define UIC_PCIEMSI2 0x00000020 /* */ -#define UIC_EIRQ4 0x00000010 /**/ -#define UICB0_UIC2NCI 0x00000008 /* */ -#define UICB0_UIC2CI 0x00000004 /* */ -#define UICB0_UIC1NCI 0x00000002 /* */ -#define UICB0_UIC1CI 0x00000001 /* */ - -#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI | \ - UICB0_UIC1CI | UICB0_UIC2NCI) - -#define UIC_MAL_TXEOB UIC_MTE/* MAL TXEOB */ -#define UIC_MAL_RXEOB UIC_MRE/* MAL RXEOB */ -/* UIC 1 */ -#define UIC_MS 0x80000000 /* MAL SERR */ -#define UIC_MTDE 0x40000000 /* MAL TXDE */ -#define UIC_MRDE 0x20000000 /* MAL RXDE */ -#define UIC_PCIE0BMVC0 0x10000000 /* */ -#define UIC_PCIE0DCRERR 0x08000000 /* */ -#define UIC_EBC 0x04000000 /* */ -#define UIC_NDFC 0x02000000 /* */ -#define UIC_PCEI1DCRERR 0x01000000 /* */ -#define UIC_GPTCMPT8 0x00800000 /* */ -#define UIC_GPTCMPT9 0x00400000 /* */ -#define UIC_PCIE1AL 0x00200000 /* */ -#define UIC_PCIE1VPD 0x00100000 /* */ -#define UIC_RPCE1HRST 0x00080000 /* */ -#define UIC_FPCE1HRST 0x00040000 /* */ -#define UIC_PCIE1TCR 0x00020000 /* */ -#define UIC_PCIE1VC0 0x00010000 /* */ -#define UIC_GPTCMPT3 0x00008000 /* */ -#define UIC_GPTCMPT4 0x00004000 /* */ -#define UIC_EIRQ7 0x00002000 /* */ -#define UIC_EIRQ8 0x00001000 /* */ -#define UIC_EIRQ9 0x00000800 /* */ -#define UIC_GPTCMP5 0x00000400 /* */ -#define UIC_GPTCMP6 0x00000200 /* */ -#define UIC_GPTCMP7 0x00000100 /* */ -#define UIC_SROM 0x00000080 /* SERIAL ROM*/ -#define UIC_GPTDECPULS 0x00000040 /* GPT Decrement pulse*/ -#define UIC_EIRQ2 0x00000020 /* */ -#define UIC_EIRQ5 0x00000010 /* */ -#define UIC_EIRQ6 0x00000008 /* */ -#define UIC_EMAC0WAKE 0x00000004 /* */ -#define UIC_EIRQ1 0x00000002 /* */ -#define UIC_EMAC1WAKE 0x00000001 /* */ -#define UIC_MAL_SERR UIC_MS /* MAL SERR */ -#define UIC_MAL_TXDE UIC_MTDE /* MAL TXDE */ -#define UIC_MAL_RXDE UIC_MRDE /* MAL RXDE */ -/* UIC 2 */ -#define UIC_PCIE0INTA 0x80000000 /* PCIE0 INTA*/ -#define UIC_PCIE0INTB 0x40000000 /* PCIE0 INTB*/ -#define UIC_PCIE0INTC 0x20000000 /* PCIE0 INTC*/ -#define UIC_PCIE0INTD 0x10000000 /* PCIE0 INTD*/ -#define UIC_EIRQ3 0x08000000 /* External IRQ 3*/ -#define UIC_DDRMCUE 0x04000000 /* */ -#define UIC_DDRMCCE 0x02000000 /* */ -#define UIC_MALINTCOATX0 0x01000000 /* Interrupt coalecence TX0*/ -#define UIC_MALINTCOATX1 0x00800000 /* Interrupt coalecence TX1*/ -#define UIC_MALINTCOARX0 0x00400000 /* Interrupt coalecence RX0*/ -#define UIC_MALINTCOARX1 0x00200000 /* Interrupt coalecence RX1*/ -#define UIC_PCIE1INTA 0x00100000 /* PCIE0 INTA*/ -#define UIC_PCIE1INTB 0x00080000 /* PCIE0 INTB*/ -#define UIC_PCIE1INTC 0x00040000 /* PCIE0 INTC*/ -#define UIC_PCIE1INTD 0x00020000 /* PCIE0 INTD*/ -#define UIC_RPCIEMSI2 0x00010000 /* MSI level 2 Note this looks same as uic0-26*/ -#define UIC_PCIEMSI3 0x00008000 /* MSI level 2*/ -#define UIC_PCIEMSI4 0x00004000 /* MSI level 2*/ -#define UIC_PCIEMSI5 0x00002000 /* MSI level 2*/ -#define UIC_PCIEMSI6 0x00001000 /* MSI level 2*/ -#define UIC_PCIEMSI7 0x00000800 /* MSI level 2*/ -#define UIC_PCIEMSI8 0x00000400 /* MSI level 2*/ -#define UIC_PCIEMSI9 0x00000200 /* MSI level 2*/ -#define UIC_PCIEMSI10 0x00000100 /* MSI level 2*/ -#define UIC_PCIEMSI11 0x00000080 /* MSI level 2*/ -#define UIC_PCIEMSI12 0x00000040 /* MSI level 2*/ -#define UIC_PCIEMSI13 0x00000020 /* MSI level 2*/ -#define UIC_PCIEMSI14 0x00000010 /* MSI level 2*/ -#define UIC_PCIEMSI15 0x00000008 /* MSI level 2*/ -#define UIC_PLB4XAHB 0x00000004 /* PLBxAHB bridge*/ -#define UIC_USBWAKE 0x00000002 /* USB wakup*/ -#define UIC_USBOTG 0x00000001 /* USB OTG*/ -#define UIC_ETH0 UIC_ENET -#define UIC_ETH1 UIC_ENET1 - -#else /* !defined(CONFIG_405EZ) */ - -#define UIC_UART0 0x80000000 /* UART 0 */ -#define UIC_UART1 0x40000000 /* UART 1 */ -#define UIC_IIC 0x20000000 /* IIC */ -#define UIC_EXT_MAST 0x10000000 /* External Master */ -#define UIC_PCI 0x08000000 /* PCI write to command reg */ -#define UIC_DMA0 0x04000000 /* DMA chan. 0 */ -#define UIC_DMA1 0x02000000 /* DMA chan. 1 */ -#define UIC_DMA2 0x01000000 /* DMA chan. 2 */ -#define UIC_DMA3 0x00800000 /* DMA chan. 3 */ -#define UIC_EMAC_WAKE 0x00400000 /* EMAC wake up */ -#define UIC_MAL_SERR 0x00200000 /* MAL SERR */ -#define UIC_MAL_TXEOB 0x00100000 /* MAL TXEOB */ -#define UIC_MAL_RXEOB 0x00080000 /* MAL RXEOB */ -#define UIC_MAL_TXDE 0x00040000 /* MAL TXDE */ -#define UIC_MAL_RXDE 0x00020000 /* MAL RXDE */ -#define UIC_ENET 0x00010000 /* Ethernet0 */ -#define UIC_ENET1 0x00004000 /* Ethernet1 on 405EP */ -#define UIC_ECC_CE 0x00004000 /* ECC Correctable Error on 405GP */ -#define UIC_EXT_PCI_SERR 0x00008000 /* External PCI SERR# */ -#define UIC_PCI_PM 0x00002000 /* PCI Power Management */ -#define UIC_EXT0 0x00000040 /* External interrupt 0 */ -#define UIC_EXT1 0x00000020 /* External interrupt 1 */ -#define UIC_EXT2 0x00000010 /* External interrupt 2 */ -#define UIC_EXT3 0x00000008 /* External interrupt 3 */ -#define UIC_EXT4 0x00000004 /* External interrupt 4 */ -#define UIC_EXT5 0x00000002 /* External interrupt 5 */ -#define UIC_EXT6 0x00000001 /* External interrupt 6 */ -#endif /* defined(CONFIG_405EZ) */ - -/****************************************************************************** - * External Bus Controller (EBC) - *****************************************************************************/ - -/* Bank Configuration Register */ -#define EBC_BXCR_BAS_MASK PPC_REG_VAL(11, 0xFFF) -#define EBC_BXCR_BAS_ENCODE(n) (((static_cast(unsigned long, n)) & \ - EBC_BXCR_BAS_MASK) << 0) -#define EBC_BXCR_BS_MASK PPC_REG_VAL(14, 0x7) -#define EBC_BXCR_BS_1MB PPC_REG_VAL(14, 0x0) -#define EBC_BXCR_BS_2MB PPC_REG_VAL(14, 0x1) -#define EBC_BXCR_BS_4MB PPC_REG_VAL(14, 0x2) -#define EBC_BXCR_BS_8MB PPC_REG_VAL(14, 0x3) -#define EBC_BXCR_BS_16MB PPC_REG_VAL(14, 0x4) -#define EBC_BXCR_BS_32MB PPC_REG_VAL(14, 0x5) -#define EBC_BXCR_BS_64MB PPC_REG_VAL(14, 0x6) -#define EBC_BXCR_BS_128MB PPC_REG_VAL(14, 0x7) -#define EBC_BXCR_BU_MASK PPC_REG_VAL(16, 0x3) -#define EBC_BXCR_BU_NONE PPC_REG_VAL(16, 0x0) -#define EBC_BXCR_BU_R PPC_REG_VAL(16, 0x1) -#define EBC_BXCR_BU_W PPC_REG_VAL(16, 0x2) -#define EBC_BXCR_BU_RW PPC_REG_VAL(16, 0x3) -#define EBC_BXCR_BW_MASK PPC_REG_VAL(18, 0x3) -#define EBC_BXCR_BW_8BIT PPC_REG_VAL(18, 0x0) -#define EBC_BXCR_BW_16BIT PPC_REG_VAL(18, 0x1) -#define EBC_BXCR_BW_32BIT PPC_REG_VAL(18, 0x3) - -/* Bank Access Parameter Register */ -#define EBC_BXAP_BME_ENABLED PPC_REG_VAL(0, 0x1) -#define EBC_BXAP_BME_DISABLED PPC_REG_VAL(0, 0x0) -#define EBC_BXAP_TWT_ENCODE(n) PPC_REG_VAL(8, \ - (static_cast(unsigned long, n)) \ - & 0xFF) -#define EBC_BXAP_FWT_ENCODE(n) PPC_REG_VAL(5, \ - (static_cast(unsigned long, n)) \ - & 0x1F) -#define EBC_BXAP_BWT_ENCODE(n) PPC_REG_VAL(8, \ - (static_cast(unsigned long, n)) \ - & 0x7) -#define EBC_BXAP_BCE_DISABLE PPC_REG_VAL(9, 0x0) -#define EBC_BXAP_BCE_ENABLE PPC_REG_VAL(9, 0x1) -#define EBC_BXAP_BCT_MASK PPC_REG_VAL(11, 0x3) -#define EBC_BXAP_BCT_2TRANS PPC_REG_VAL(11, 0x0) -#define EBC_BXAP_BCT_4TRANS PPC_REG_VAL(11, 0x1) -#define EBC_BXAP_BCT_8TRANS PPC_REG_VAL(11, 0x2) -#define EBC_BXAP_BCT_16TRANS PPC_REG_VAL(11, 0x3) -#define EBC_BXAP_CSN_ENCODE(n) PPC_REG_VAL(13, \ - (static_cast(unsigned long, n)) \ - & 0x3) -#define EBC_BXAP_OEN_ENCODE(n) PPC_REG_VAL(15, \ - (static_cast(unsigned long, n)) \ - & 0x3) -#define EBC_BXAP_WBN_ENCODE(n) PPC_REG_VAL(17, \ - (static_cast(unsigned long, n)) \ - & 0x3) -#define EBC_BXAP_WBF_ENCODE(n) PPC_REG_VAL(19, \ - (static_cast(unsigned long, n)) \ - & 0x3) -#define EBC_BXAP_TH_ENCODE(n) PPC_REG_VAL(22, \ - (static_cast(unsigned long, n)) \ - & 0x7) -#define EBC_BXAP_RE_ENABLED PPC_REG_VAL(23, 0x1) -#define EBC_BXAP_RE_DISABLED PPC_REG_VAL(23, 0x0) -#define EBC_BXAP_SOR_DELAYED PPC_REG_VAL(24, 0x0) -#define EBC_BXAP_SOR_NONDELAYED PPC_REG_VAL(24, 0x1) -#define EBC_BXAP_BEM_WRITEONLY PPC_REG_VAL(25, 0x0) -#define EBC_BXAP_BEM_RW PPC_REG_VAL(25, 0x1) -#define EBC_BXAP_PEN_DISABLED PPC_REG_VAL(26, 0x0) -#define EBC_BXAP_PEN_ENABLED PPC_REG_VAL(26, 0x1) - -/* Configuration Register */ -#define EBC_CFG_LE_MASK PPC_REG_VAL(0, 0x1) -#define EBC_CFG_LE_UNLOCK PPC_REG_VAL(0, 0x0) -#define EBC_CFG_LE_LOCK PPC_REG_VAL(0, 0x1) -#define EBC_CFG_PTD_MASK PPC_REG_VAL(1, 0x1) -#define EBC_CFG_PTD_ENABLE PPC_REG_VAL(1, 0x0) -#define EBC_CFG_PTD_DISABLE PPC_REG_VAL(1, 0x1) -#define EBC_CFG_RTC_MASK PPC_REG_VAL(4, 0x7) -#define EBC_CFG_RTC_16PERCLK PPC_REG_VAL(4, 0x0) -#define EBC_CFG_RTC_32PERCLK PPC_REG_VAL(4, 0x1) -#define EBC_CFG_RTC_64PERCLK PPC_REG_VAL(4, 0x2) -#define EBC_CFG_RTC_128PERCLK PPC_REG_VAL(4, 0x3) -#define EBC_CFG_RTC_256PERCLK PPC_REG_VAL(4, 0x4) -#define EBC_CFG_RTC_512PERCLK PPC_REG_VAL(4, 0x5) -#define EBC_CFG_RTC_1024PERCLK PPC_REG_VAL(4, 0x6) -#define EBC_CFG_RTC_2048PERCLK PPC_REG_VAL(4, 0x7) -#define EBC_CFG_ATC_MASK PPC_REG_VAL(5, 0x1) -#define EBC_CFG_ATC_HI PPC_REG_VAL(5, 0x0) -#define EBC_CFG_ATC_PREVIOUS PPC_REG_VAL(5, 0x1) -#define EBC_CFG_DTC_MASK PPC_REG_VAL(6, 0x1) -#define EBC_CFG_DTC_HI PPC_REG_VAL(6, 0x0) -#define EBC_CFG_DTC_PREVIOUS PPC_REG_VAL(6, 0x1) -#define EBC_CFG_CTC_MASK PPC_REG_VAL(7, 0x1) -#define EBC_CFG_CTC_HI PPC_REG_VAL(7, 0x0) -#define EBC_CFG_CTC_PREVIOUS PPC_REG_VAL(7, 0x1) -#define EBC_CFG_OEO_MASK PPC_REG_VAL(8, 0x1) -#define EBC_CFG_OEO_DISABLE PPC_REG_VAL(8, 0x0) -#define EBC_CFG_OEO_ENABLE PPC_REG_VAL(8, 0x1) -#define EBC_CFG_EMC_MASK PPC_REG_VAL(9, 0x1) -#define EBC_CFG_EMC_NONDEFAULT PPC_REG_VAL(9, 0x0) -#define EBC_CFG_EMC_DEFAULT PPC_REG_VAL(9, 0x1) -#define EBC_CFG_PME_MASK PPC_REG_VAL(14, 0x1) -#define EBC_CFG_PME_DISABLE PPC_REG_VAL(14, 0x0) -#define EBC_CFG_PME_ENABLE PPC_REG_VAL(14, 0x1) -#define EBC_CFG_PMT_MASK PPC_REG_VAL(19, 0x1F) -#define EBC_CFG_PMT_ENCODE(n) PPC_REG_VAL(19, \ - (static_cast(unsigned long, n)) \ - & 0x1F) -#define EBC_CFG_PR_MASK PPC_REG_VAL(21, 0x3) -#define EBC_CFG_PR_16 PPC_REG_VAL(21, 0x0) -#define EBC_CFG_PR_32 PPC_REG_VAL(21, 0x1) -#define EBC_CFG_PR_64 PPC_REG_VAL(21, 0x2) -#define EBC_CFG_PR_128 PPC_REG_VAL(21, 0x3) - #ifndef CONFIG_405EP /****************************************************************************** * Decompression Controller @@ -1254,6 +893,42 @@ #if defined(CONFIG_405EX) #define SDR0_SRST 0x0200 +/* + * Software Reset Register + */ +#define SDR0_SRST_BGO PPC_REG_VAL(0, 1) +#define SDR0_SRST_PLB4 PPC_REG_VAL(1, 1) +#define SDR0_SRST_EBC PPC_REG_VAL(2, 1) +#define SDR0_SRST_OPB PPC_REG_VAL(3, 1) +#define SDR0_SRST_UART0 PPC_REG_VAL(4, 1) +#define SDR0_SRST_UART1 PPC_REG_VAL(5, 1) +#define SDR0_SRST_IIC0 PPC_REG_VAL(6, 1) +#define SDR0_SRST_BGI PPC_REG_VAL(7, 1) +#define SDR0_SRST_GPIO PPC_REG_VAL(8, 1) +#define SDR0_SRST_GPT PPC_REG_VAL(9, 1) +#define SDR0_SRST_DMC PPC_REG_VAL(10, 1) +#define SDR0_SRST_RGMII PPC_REG_VAL(11, 1) +#define SDR0_SRST_EMAC0 PPC_REG_VAL(12, 1) +#define SDR0_SRST_EMAC1 PPC_REG_VAL(13, 1) +#define SDR0_SRST_CPM PPC_REG_VAL(14, 1) +#define SDR0_SRST_EPLL PPC_REG_VAL(15, 1) +#define SDR0_SRST_UIC PPC_REG_VAL(16, 1) +#define SDR0_SRST_UPRST PPC_REG_VAL(17, 1) +#define SDR0_SRST_IIC1 PPC_REG_VAL(18, 1) +#define SDR0_SRST_SCP PPC_REG_VAL(19, 1) +#define SDR0_SRST_UHRST PPC_REG_VAL(20, 1) +#define SDR0_SRST_DMA PPC_REG_VAL(21, 1) +#define SDR0_SRST_DMAC PPC_REG_VAL(22, 1) +#define SDR0_SRST_MAL PPC_REG_VAL(23, 1) +#define SDR0_SRST_EBM PPC_REG_VAL(24, 1) +#define SDR0_SRST_GPTR PPC_REG_VAL(25, 1) +#define SDR0_SRST_PE0 PPC_REG_VAL(26, 1) +#define SDR0_SRST_PE1 PPC_REG_VAL(27, 1) +#define SDR0_SRST_CRYP PPC_REG_VAL(28, 1) +#define SDR0_SRST_PKP PPC_REG_VAL(29, 1) +#define SDR0_SRST_AHB PPC_REG_VAL(30, 1) +#define SDR0_SRST_NDFC PPC_REG_VAL(31, 1) + #define sdr_uart0 0x0120 /* UART0 Config */ #define sdr_uart1 0x0121 /* UART1 Config */ #define sdr_mfr 0x4300 /* SDR0_MFR reg */ diff --git a/include/ppc440.h b/include/ppc440.h index c581f1b..92db15f 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -77,7 +77,6 @@ #define tbl 0x11c /* time base lower (supervisor)*/ #define tbu 0x11d /* time base upper (supervisor)*/ #define pir 0x11e /* processor id register */ -/*#define pvr 0x11f processor version register */ #define dbsr 0x130 /* debug status register */ #define dbcr0 0x134 /* debug control register 0 */ #define dbcr1 0x135 /* debug control register 1 */ @@ -268,86 +267,6 @@ #define sdr_sdstp6 0x4005 #define sdr_sdstp7 0x4007 -/****************************************************************************** - * PCI express defines - ******************************************************************************/ -#define SDR0_PE0UTLSET1 0x00000300 /* PE0 Upper transaction layer conf setting */ -#define SDR0_PE0UTLSET2 0x00000301 /* PE0 Upper transaction layer conf setting 2 */ -#define SDR0_PE0DLPSET 0x00000302 /* PE0 Data link & logical physical configuration */ -#define SDR0_PE0LOOP 0x00000303 /* PE0 Loopback interface status */ -#define SDR0_PE0RCSSET 0x00000304 /* PE0 Reset, clock & shutdown setting */ -#define SDR0_PE0RCSSTS 0x00000305 /* PE0 Reset, clock & shutdown status */ -#define SDR0_PE0HSSSET1L0 0x00000306 /* PE0 HSS Control Setting 1: Lane 0 */ -#define SDR0_PE0HSSSET2L0 0x00000307 /* PE0 HSS Control Setting 2: Lane 0 */ -#define SDR0_PE0HSSSTSL0 0x00000308 /* PE0 HSS Control Status : Lane 0 */ -#define SDR0_PE0HSSSET1L1 0x00000309 /* PE0 HSS Control Setting 1: Lane 1 */ -#define SDR0_PE0HSSSET2L1 0x0000030A /* PE0 HSS Control Setting 2: Lane 1 */ -#define SDR0_PE0HSSSTSL1 0x0000030B /* PE0 HSS Control Status : Lane 1 */ -#define SDR0_PE0HSSSET1L2 0x0000030C /* PE0 HSS Control Setting 1: Lane 2 */ -#define SDR0_PE0HSSSET2L2 0x0000030D /* PE0 HSS Control Setting 2: Lane 2 */ -#define SDR0_PE0HSSSTSL2 0x0000030E /* PE0 HSS Control Status : Lane 2 */ -#define SDR0_PE0HSSSET1L3 0x0000030F /* PE0 HSS Control Setting 1: Lane 3 */ -#define SDR0_PE0HSSSET2L3 0x00000310 /* PE0 HSS Control Setting 2: Lane 3 */ -#define SDR0_PE0HSSSTSL3 0x00000311 /* PE0 HSS Control Status : Lane 3 */ -#define SDR0_PE0HSSSET1L4 0x00000312 /* PE0 HSS Control Setting 1: Lane 4 */ -#define SDR0_PE0HSSSET2L4 0x00000313 /* PE0 HSS Control Setting 2: Lane 4 */ -#define SDR0_PE0HSSSTSL4 0x00000314 /* PE0 HSS Control Status : Lane 4 */ -#define SDR0_PE0HSSSET1L5 0x00000315 /* PE0 HSS Control Setting 1: Lane 5 */ -#define SDR0_PE0HSSSET2L5 0x00000316 /* PE0 HSS Control Setting 2: Lane 5 */ -#define SDR0_PE0HSSSTSL5 0x00000317 /* PE0 HSS Control Status : Lane 5 */ -#define SDR0_PE0HSSSET1L6 0x00000318 /* PE0 HSS Control Setting 1: Lane 6 */ -#define SDR0_PE0HSSSET2L6 0x00000319 /* PE0 HSS Control Setting 2: Lane 6 */ -#define SDR0_PE0HSSSTSL6 0x0000031A /* PE0 HSS Control Status : Lane 6 */ -#define SDR0_PE0HSSSET1L7 0x0000031B /* PE0 HSS Control Setting 1: Lane 7 */ -#define SDR0_PE0HSSSET2L7 0x0000031C /* PE0 HSS Control Setting 2: Lane 7 */ -#define SDR0_PE0HSSSTSL7 0x0000031D /* PE0 HSS Control Status : Lane 7 */ -#define SDR0_PE0HSSSEREN 0x0000031E /* PE0 Serdes Transmitter Enable */ -#define SDR0_PE0LANEABCD 0x0000031F /* PE0 Lanes ABCD affectation */ -#define SDR0_PE0LANEEFGH 0x00000320 /* PE0 Lanes EFGH affectation */ - -#define SDR0_PE1UTLSET1 0x00000340 /* PE1 Upper transaction layer conf setting */ -#define SDR0_PE1UTLSET2 0x00000341 /* PE1 Upper transaction layer conf setting 2 */ -#define SDR0_PE1DLPSET 0x00000342 /* PE1 Data link & logical physical configuration */ -#define SDR0_PE1LOOP 0x00000343 /* PE1 Loopback interface status */ -#define SDR0_PE1RCSSET 0x00000344 /* PE1 Reset, clock & shutdown setting */ -#define SDR0_PE1RCSSTS 0x00000345 /* PE1 Reset, clock & shutdown status */ -#define SDR0_PE1HSSSET1L0 0x00000346 /* PE1 HSS Control Setting 1: Lane 0 */ -#define SDR0_PE1HSSSET2L0 0x00000347 /* PE1 HSS Control Setting 2: Lane 0 */ -#define SDR0_PE1HSSSTSL0 0x00000348 /* PE1 HSS Control Status : Lane 0 */ -#define SDR0_PE1HSSSET1L1 0x00000349 /* PE1 HSS Control Setting 1: Lane 1 */ -#define SDR0_PE1HSSSET2L1 0x0000034A /* PE1 HSS Control Setting 2: Lane 1 */ -#define SDR0_PE1HSSSTSL1 0x0000034B /* PE1 HSS Control Status : Lane 1 */ -#define SDR0_PE1HSSSET1L2 0x0000034C /* PE1 HSS Control Setting 1: Lane 2 */ -#define SDR0_PE1HSSSET2L2 0x0000034D /* PE1 HSS Control Setting 2: Lane 2 */ -#define SDR0_PE1HSSSTSL2 0x0000034E /* PE1 HSS Control Status : Lane 2 */ -#define SDR0_PE1HSSSET1L3 0x0000034F /* PE1 HSS Control Setting 1: Lane 3 */ -#define SDR0_PE1HSSSET2L3 0x00000350 /* PE1 HSS Control Setting 2: Lane 3 */ -#define SDR0_PE1HSSSTSL3 0x00000351 /* PE1 HSS Control Status : Lane 3 */ -#define SDR0_PE1HSSSEREN 0x00000352 /* PE1 Serdes Transmitter Enable */ -#define SDR0_PE1LANEABCD 0x00000353 /* PE1 Lanes ABCD affectation */ -#define SDR0_PE2UTLSET1 0x00000370 /* PE2 Upper transaction layer conf setting */ -#define SDR0_PE2UTLSET2 0x00000371 /* PE2 Upper transaction layer conf setting 2 */ -#define SDR0_PE2DLPSET 0x00000372 /* PE2 Data link & logical physical configuration */ -#define SDR0_PE2LOOP 0x00000373 /* PE2 Loopback interface status */ -#define SDR0_PE2RCSSET 0x00000374 /* PE2 Reset, clock & shutdown setting */ -#define SDR0_PE2RCSSTS 0x00000375 /* PE2 Reset, clock & shutdown status */ -#define SDR0_PE2HSSSET1L0 0x00000376 /* PE2 HSS Control Setting 1: Lane 0 */ -#define SDR0_PE2HSSSET2L0 0x00000377 /* PE2 HSS Control Setting 2: Lane 0 */ -#define SDR0_PE2HSSSTSL0 0x00000378 /* PE2 HSS Control Status : Lane 0 */ -#define SDR0_PE2HSSSET1L1 0x00000379 /* PE2 HSS Control Setting 1: Lane 1 */ -#define SDR0_PE2HSSSET2L1 0x0000037A /* PE2 HSS Control Setting 2: Lane 1 */ -#define SDR0_PE2HSSSTSL1 0x0000037B /* PE2 HSS Control Status : Lane 1 */ -#define SDR0_PE2HSSSET1L2 0x0000037C /* PE2 HSS Control Setting 1: Lane 2 */ -#define SDR0_PE2HSSSET2L2 0x0000037D /* PE2 HSS Control Setting 2: Lane 2 */ -#define SDR0_PE2HSSSTSL2 0x0000037E /* PE2 HSS Control Status : Lane 2 */ -#define SDR0_PE2HSSSET1L3 0x0000037F /* PE2 HSS Control Setting 1: Lane 3 */ -#define SDR0_PE2HSSSET2L3 0x00000380 /* PE2 HSS Control Setting 2: Lane 3 */ -#define SDR0_PE2HSSSTSL3 0x00000381 /* PE2 HSS Control Status : Lane 3 */ -#define SDR0_PE2HSSSEREN 0x00000382 /* PE2 Serdes Transmitter Enable */ -#define SDR0_PE2LANEABCD 0x00000383 /* PE2 Lanes ABCD affectation */ -#define SDR0_PEGPLLSET1 0x000003A0 /* PE Pll LC Tank Setting1 */ -#define SDR0_PEGPLLSET2 0x000003A1 /* PE Pll LC Tank Setting2 */ -#define SDR0_PEGPLLSTS 0x000003A2 /* PE Pll LC Tank Status */ #endif /* CONFIG_440SPE */ /*----------------------------------------------------------------------------- @@ -749,7 +668,8 @@ +----------------------------------------------------------------------------*/ #if defined (CONFIG_440GX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) #define L2_CACHE_BASE 0x030 #define l2_cache_cfg (L2_CACHE_BASE+0x00) /* L2 Cache Config */ #define l2_cache_cmd (L2_CACHE_BASE+0x01) /* L2 Cache Command */ @@ -837,7 +757,8 @@ /*----------------------------------------------------------------------------- | Clocking, Power Management and Chip Control +----------------------------------------------------------------------------*/ -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) #define CNTRL_DCR_BASE 0x160 #else #define CNTRL_DCR_BASE 0x0b0 @@ -863,193 +784,6 @@ #define cntrl1 (CNTRL_DCR_BASE+0x3a) /* Control 1 register */ /*----------------------------------------------------------------------------- - | Universal interrupt controller - +----------------------------------------------------------------------------*/ -#define UIC_SR 0x0 /* UIC status */ -#define UIC_ER 0x2 /* UIC enable */ -#define UIC_CR 0x3 /* UIC critical */ -#define UIC_PR 0x4 /* UIC polarity */ -#define UIC_TR 0x5 /* UIC triggering */ -#define UIC_MSR 0x6 /* UIC masked status */ -#define UIC_VR 0x7 /* UIC vector */ -#define UIC_VCR 0x8 /* UIC vector configuration */ - -#define UIC0_DCR_BASE 0xc0 -#define uic0sr (UIC0_DCR_BASE+0x0) /* UIC0 status */ -#define uic0er (UIC0_DCR_BASE+0x2) /* UIC0 enable */ -#define uic0cr (UIC0_DCR_BASE+0x3) /* UIC0 critical */ -#define uic0pr (UIC0_DCR_BASE+0x4) /* UIC0 polarity */ -#define uic0tr (UIC0_DCR_BASE+0x5) /* UIC0 triggering */ -#define uic0msr (UIC0_DCR_BASE+0x6) /* UIC0 masked status */ -#define uic0vr (UIC0_DCR_BASE+0x7) /* UIC0 vector */ -#define uic0vcr (UIC0_DCR_BASE+0x8) /* UIC0 vector configuration */ - -#define UIC1_DCR_BASE 0xd0 -#define uic1sr (UIC1_DCR_BASE+0x0) /* UIC1 status */ -#define uic1er (UIC1_DCR_BASE+0x2) /* UIC1 enable */ -#define uic1cr (UIC1_DCR_BASE+0x3) /* UIC1 critical */ -#define uic1pr (UIC1_DCR_BASE+0x4) /* UIC1 polarity */ -#define uic1tr (UIC1_DCR_BASE+0x5) /* UIC1 triggering */ -#define uic1msr (UIC1_DCR_BASE+0x6) /* UIC1 masked status */ -#define uic1vr (UIC1_DCR_BASE+0x7) /* UIC1 vector */ -#define uic1vcr (UIC1_DCR_BASE+0x8) /* UIC1 vector configuration */ - -#if defined(CONFIG_440SPE) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) -#define UIC2_DCR_BASE 0xe0 -#define uic2sr (UIC2_DCR_BASE+0x0) /* UIC2 status-Read Clear */ -#define uic2srs (UIC2_DCR_BASE+0x1) /* UIC2 status-Read Set */ -#define uic2er (UIC2_DCR_BASE+0x2) /* UIC2 enable */ -#define uic2cr (UIC2_DCR_BASE+0x3) /* UIC2 critical */ -#define uic2pr (UIC2_DCR_BASE+0x4) /* UIC2 polarity */ -#define uic2tr (UIC2_DCR_BASE+0x5) /* UIC2 triggering */ -#define uic2msr (UIC2_DCR_BASE+0x6) /* UIC2 masked status */ -#define uic2vr (UIC2_DCR_BASE+0x7) /* UIC2 vector */ -#define uic2vcr (UIC2_DCR_BASE+0x8) /* UIC2 vector configuration */ - -#define UIC3_DCR_BASE 0xf0 -#define uic3sr (UIC3_DCR_BASE+0x0) /* UIC3 status-Read Clear */ -#define uic3srs (UIC3_DCR_BASE+0x1) /* UIC3 status-Read Set */ -#define uic3er (UIC3_DCR_BASE+0x2) /* UIC3 enable */ -#define uic3cr (UIC3_DCR_BASE+0x3) /* UIC3 critical */ -#define uic3pr (UIC3_DCR_BASE+0x4) /* UIC3 polarity */ -#define uic3tr (UIC3_DCR_BASE+0x5) /* UIC3 triggering */ -#define uic3msr (UIC3_DCR_BASE+0x6) /* UIC3 masked status */ -#define uic3vr (UIC3_DCR_BASE+0x7) /* UIC3 vector */ -#define uic3vcr (UIC3_DCR_BASE+0x8) /* UIC3 vector configuration */ -#endif /* CONFIG_440SPE */ - -#if defined(CONFIG_440GX) -#define UIC2_DCR_BASE 0x210 -#define uic2sr (UIC2_DCR_BASE+0x0) /* UIC2 status */ -#define uic2er (UIC2_DCR_BASE+0x2) /* UIC2 enable */ -#define uic2cr (UIC2_DCR_BASE+0x3) /* UIC2 critical */ -#define uic2pr (UIC2_DCR_BASE+0x4) /* UIC2 polarity */ -#define uic2tr (UIC2_DCR_BASE+0x5) /* UIC2 triggering */ -#define uic2msr (UIC2_DCR_BASE+0x6) /* UIC2 masked status */ -#define uic2vr (UIC2_DCR_BASE+0x7) /* UIC2 vector */ -#define uic2vcr (UIC2_DCR_BASE+0x8) /* UIC2 vector configuration */ - - -#define UIC_DCR_BASE 0x200 -#define uicb0sr (UIC_DCR_BASE+0x0) /* UIC Base Status Register */ -#define uicb0er (UIC_DCR_BASE+0x2) /* UIC Base enable */ -#define uicb0cr (UIC_DCR_BASE+0x3) /* UIC Base critical */ -#define uicb0pr (UIC_DCR_BASE+0x4) /* UIC Base polarity */ -#define uicb0tr (UIC_DCR_BASE+0x5) /* UIC Base triggering */ -#define uicb0msr (UIC_DCR_BASE+0x6) /* UIC Base masked status */ -#define uicb0vr (UIC_DCR_BASE+0x7) /* UIC Base vector */ -#define uicb0vcr (UIC_DCR_BASE+0x8) /* UIC Base vector configuration */ -#endif /* CONFIG_440GX */ - -/* The following is for compatibility with 405 code */ -#define uicsr uic0sr -#define uicer uic0er -#define uiccr uic0cr -#define uicpr uic0pr -#define uictr uic0tr -#define uicmsr uic0msr -#define uicvr uic0vr -#define uicvcr uic0vcr - -#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) -/*----------------------------------------------------------------------------+ -| Clock / Power-on-reset DCR's. -+----------------------------------------------------------------------------*/ -#define CPR0_CLKUPD 0x20 -#define CPR0_CLKUPD_BSY_MASK 0x80000000 -#define CPR0_CLKUPD_BSY_COMPLETED 0x00000000 -#define CPR0_CLKUPD_BSY_BUSY 0x80000000 -#define CPR0_CLKUPD_CUI_MASK 0x80000000 -#define CPR0_CLKUPD_CUI_DISABLE 0x00000000 -#define CPR0_CLKUPD_CUI_ENABLE 0x80000000 -#define CPR0_CLKUPD_CUD_MASK 0x40000000 -#define CPR0_CLKUPD_CUD_DISABLE 0x00000000 -#define CPR0_CLKUPD_CUD_ENABLE 0x40000000 - -#define CPR0_PLLC 0x40 -#define CPR0_PLLC_RST_MASK 0x80000000 -#define CPR0_PLLC_RST_PLLLOCKED 0x00000000 -#define CPR0_PLLC_RST_PLLRESET 0x80000000 -#define CPR0_PLLC_ENG_MASK 0x40000000 -#define CPR0_PLLC_ENG_DISABLE 0x00000000 -#define CPR0_PLLC_ENG_ENABLE 0x40000000 -#define CPR0_PLLC_ENG_ENCODE(n) ((((unsigned long)(n))&0x01)<<30) -#define CPR0_PLLC_ENG_DECODE(n) ((((unsigned long)(n))>>30)&0x01) -#define CPR0_PLLC_SRC_MASK 0x20000000 -#define CPR0_PLLC_SRC_PLLOUTA 0x00000000 -#define CPR0_PLLC_SRC_PLLOUTB 0x20000000 -#define CPR0_PLLC_SRC_ENCODE(n) ((((unsigned long)(n))&0x01)<<29) -#define CPR0_PLLC_SRC_DECODE(n) ((((unsigned long)(n))>>29)&0x01) -#define CPR0_PLLC_SEL_MASK 0x07000000 -#define CPR0_PLLC_SEL_PLLOUT 0x00000000 -#define CPR0_PLLC_SEL_CPU 0x01000000 -#define CPR0_PLLC_SEL_EBC 0x05000000 -#define CPR0_PLLC_SEL_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) -#define CPR0_PLLC_SEL_DECODE(n) ((((unsigned long)(n))>>24)&0x07) -#define CPR0_PLLC_TUNE_MASK 0x000003FF -#define CPR0_PLLC_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) -#define CPR0_PLLC_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF) - -#define CPR0_PLLD 0x60 -#define CPR0_PLLD_FBDV_MASK 0x1F000000 -#define CPR0_PLLD_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) -#define CPR0_PLLD_FBDV_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x1F)+1) -#define CPR0_PLLD_FWDVA_MASK 0x000F0000 -#define CPR0_PLLD_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<16) -#define CPR0_PLLD_FWDVA_DECODE(n) ((((((unsigned long)(n))>>16)-1)&0x0F)+1) -#define CPR0_PLLD_FWDVB_MASK 0x00000700 -#define CPR0_PLLD_FWDVB_ENCODE(n) ((((unsigned long)(n))&0x07)<<8) -#define CPR0_PLLD_FWDVB_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x07)+1) -#define CPR0_PLLD_LFBDV_MASK 0x0000003F -#define CPR0_PLLD_LFBDV_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0) -#define CPR0_PLLD_LFBDV_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x3F)+1) - -#define CPR0_PRIMAD 0x80 -#define CPR0_PRIMAD_PRADV0_MASK 0x07000000 -#define CPR0_PRIMAD_PRADV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) -#define CPR0_PRIMAD_PRADV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) - -#define CPR0_PRIMBD 0xA0 -#define CPR0_PRIMBD_PRBDV0_MASK 0x07000000 -#define CPR0_PRIMBD_PRBDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) -#define CPR0_PRIMBD_PRBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) - -#define CPR0_OPBD 0xC0 -#define CPR0_OPBD_OPBDV0_MASK 0x03000000 -#define CPR0_OPBD_OPBDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) -#define CPR0_OPBD_OPBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) - -#define CPR0_PERD 0xE0 -#if !defined(CONFIG_440EPX) -#define CPR0_PERD_PERDV0_MASK 0x03000000 -#define CPR0_PERD_PERDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) -#define CPR0_PERD_PERDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) -#endif - -#define CPR0_MALD 0x100 -#define CPR0_MALD_MALDV0_MASK 0x03000000 -#define CPR0_MALD_MALDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) -#define CPR0_MALD_MALDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) - -#define CPR0_ICFG 0x140 -#define CPR0_ICFG_RLI_MASK 0x80000000 -#define CPR0_ICFG_RLI_RESETCPR 0x00000000 -#define CPR0_ICFG_RLI_PRESERVECPR 0x80000000 -#define CPR0_ICFG_ICS_MASK 0x00000007 -#define CPR0_ICFG_ICS_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0) -#define CPR0_ICFG_ICS_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x3F)+1) - -/************************/ -/* IIC defines */ -/************************/ -#define IIC0_MMIO_BASE 0xA0000400 -#define IIC1_MMIO_BASE 0xA0000500 - -#endif /* CONFIG_440SP */ - -/*----------------------------------------------------------------------------- | DMA +----------------------------------------------------------------------------*/ #if defined(CONFIG_460EX) || defined(CONFIG_460GT) @@ -1136,708 +870,6 @@ #define malrcbs24 (MAL_DCR_BASE+0x78) /* RX 24 Channel buffer size reg */ #endif /* CONFIG_440GX */ - -/*---------------------------------------------------------------------------+ -| Universal interrupt controller 0 interrupts (UIC0) -+---------------------------------------------------------------------------*/ -#if defined(CONFIG_440SP) -#define UIC_U0 0x80000000 /* UART 0 */ -#define UIC_U1 0x40000000 /* UART 1 */ -#define UIC_IIC0 0x20000000 /* IIC */ -#define UIC_IIC1 0x10000000 /* IIC */ -#define UIC_PIM 0x08000000 /* PCI0 inbound message */ -#define UIC_PCRW 0x04000000 /* PCI0 command write register */ -#define UIC_PPM 0x02000000 /* PCI0 power management */ -#define UIC_PVPD 0x01000000 /* PCI0 VPD Access */ -#define UIC_MSI0 0x00800000 /* PCI0 MSI level 0 */ -#define UIC_P1IM 0x00400000 /* PCI1 Inbound Message */ -#define UIC_P1CRW 0x00200000 /* PCI1 command write register */ -#define UIC_P1PM 0x00100000 /* PCI1 power management */ -#define UIC_P1VPD 0x00080000 /* PCI1 VPD Access */ -#define UIC_P1MSI0 0x00040000 /* PCI1 MSI level 0 */ -#define UIC_P2IM 0x00020000 /* PCI2 inbound message */ -#define UIC_P2CRW 0x00010000 /* PCI2 command register write */ -#define UIC_P2PM 0x00008000 /* PCI2 power management */ -#define UIC_P2VPD 0x00004000 /* PCI2 VPD access */ -#define UIC_P2MSI0 0x00002000 /* PCI2 MSI level 0 */ -#define UIC_D0CPF 0x00001000 /* DMA0 command pointer */ -#define UIC_D0CSF 0x00000800 /* DMA0 command status */ -#define UIC_D1CPF 0x00000400 /* DMA1 command pointer */ -#define UIC_D1CSF 0x00000200 /* DMA1 command status */ -#define UIC_I2OID 0x00000100 /* I2O inbound doorbell */ -#define UIC_I2OPLF 0x00000080 /* I2O inbound post list */ -#define UIC_I2O0LL 0x00000040 /* I2O0 low latency PLB write */ -#define UIC_I2O1LL 0x00000020 /* I2O1 low latency PLB write */ -#define UIC_I2O0HB 0x00000010 /* I2O0 high bandwidth PLB write */ -#define UIC_I2O1HB 0x00000008 /* I2O1 high bandwidth PLB write */ -#define UIC_GPTCT 0x00000004 /* GPT count timer */ -#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ -#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ -#elif defined(CONFIG_440GX) || defined(CONFIG_440EP) -#define UIC_U0 0x80000000 /* UART 0 */ -#define UIC_U1 0x40000000 /* UART 1 */ -#define UIC_IIC0 0x20000000 /* IIC */ -#define UIC_IIC1 0x10000000 /* IIC */ -#define UIC_PIM 0x08000000 /* PCI inbound message */ -#define UIC_PCRW 0x04000000 /* PCI command register write */ -#define UIC_PPM 0x02000000 /* PCI power management */ -#define UIC_MSI0 0x01000000 /* PCI MSI level 0 */ -#define UIC_MSI1 0x00800000 /* PCI MSI level 1 */ -#define UIC_MSI2 0x00400000 /* PCI MSI level 2 */ -#define UIC_MTE 0x00200000 /* MAL TXEOB */ -#define UIC_MRE 0x00100000 /* MAL RXEOB */ -#define UIC_D0 0x00080000 /* DMA channel 0 */ -#define UIC_D1 0x00040000 /* DMA channel 1 */ -#define UIC_D2 0x00020000 /* DMA channel 2 */ -#define UIC_D3 0x00010000 /* DMA channel 3 */ -#define UIC_RSVD0 0x00008000 /* Reserved */ -#define UIC_RSVD1 0x00004000 /* Reserved */ -#define UIC_CT0 0x00002000 /* GPT compare timer 0 */ -#define UIC_CT1 0x00001000 /* GPT compare timer 1 */ -#define UIC_CT2 0x00000800 /* GPT compare timer 2 */ -#define UIC_CT3 0x00000400 /* GPT compare timer 3 */ -#define UIC_CT4 0x00000200 /* GPT compare timer 4 */ -#define UIC_EIR0 0x00000100 /* External interrupt 0 */ -#define UIC_EIR1 0x00000080 /* External interrupt 1 */ -#define UIC_EIR2 0x00000040 /* External interrupt 2 */ -#define UIC_EIR3 0x00000020 /* External interrupt 3 */ -#define UIC_EIR4 0x00000010 /* External interrupt 4 */ -#define UIC_EIR5 0x00000008 /* External interrupt 5 */ -#define UIC_EIR6 0x00000004 /* External interrupt 6 */ -#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ -#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ - -#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) - -#define UIC_U0 0x80000000 /* UART 0 */ -#define UIC_U1 0x40000000 /* UART 1 */ -#define UIC_IIC0 0x20000000 /* IIC */ -#define UIC_KRD 0x10000000 /* Kasumi Ready for data */ -#define UIC_KDA 0x08000000 /* Kasumi Data Available */ -#define UIC_PCRW 0x04000000 /* PCI command register write */ -#define UIC_PPM 0x02000000 /* PCI power management */ -#define UIC_IIC1 0x01000000 /* IIC */ -#define UIC_SPI 0x00800000 /* SPI */ -#define UIC_EPCISER 0x00400000 /* External PCI SERR */ -#define UIC_MTE 0x00200000 /* MAL TXEOB */ -#define UIC_MRE 0x00100000 /* MAL RXEOB */ -#define UIC_D0 0x00080000 /* DMA channel 0 */ -#define UIC_D1 0x00040000 /* DMA channel 1 */ -#define UIC_D2 0x00020000 /* DMA channel 2 */ -#define UIC_D3 0x00010000 /* DMA channel 3 */ -#define UIC_UD0 0x00008000 /* UDMA irq 0 */ -#define UIC_UD1 0x00004000 /* UDMA irq 1 */ -#define UIC_UD2 0x00002000 /* UDMA irq 2 */ -#define UIC_UD3 0x00001000 /* UDMA irq 3 */ -#define UIC_HSB2D 0x00000800 /* USB2.0 Device */ -#define UIC_OHCI1 0x00000400 /* USB2.0 Host OHCI irq 1 */ -#define UIC_OHCI2 0x00000200 /* USB2.0 Host OHCI irq 2 */ -#define UIC_EIP94 0x00000100 /* Security EIP94 */ -#define UIC_ETH0 0x00000080 /* Emac 0 */ -#define UIC_ETH1 0x00000040 /* Emac 1 */ -#define UIC_EHCI 0x00000020 /* USB2.0 Host EHCI */ -#define UIC_EIR4 0x00000010 /* External interrupt 4 */ -#define UIC_UIC2NC 0x00000008 /* UIC2 non-critical interrupt */ -#define UIC_UIC2C 0x00000004 /* UIC2 critical interrupt */ -#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ -#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ - -/* For compatibility with 405 code */ -#define UIC_MAL_TXEOB UIC_MTE -#define UIC_MAL_RXEOB UIC_MRE - -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) - -#define UIC_RSVD0 0x80000000 /* N/A - unused */ -#define UIC_U1 0x40000000 /* UART 1 */ -#define UIC_IIC0 0x20000000 /* IIC */ -#define UIC_IIC1 0x10000000 /* IIC */ -#define UIC_PIM 0x08000000 /* PCI inbound message */ -#define UIC_PCRW 0x04000000 /* PCI command register write */ -#define UIC_PPM 0x02000000 /* PCI power management */ -#define UIC_PCIVPD 0x01000000 /* PCI VPD */ -#define UIC_MSI0 0x00800000 /* PCI MSI level 0 */ -#define UIC_EIR0 0x00400000 /* External interrupt 0 */ -#define UIC_UIC2NC 0x00200000 /* UIC2 non-critical interrupt */ -#define UIC_UIC2C 0x00100000 /* UIC2 critical interrupt */ -#define UIC_D0 0x00080000 /* DMA channel 0 */ -#define UIC_D1 0x00040000 /* DMA channel 1 */ -#define UIC_D2 0x00020000 /* DMA channel 2 */ -#define UIC_D3 0x00010000 /* DMA channel 3 */ -#define UIC_UIC3NC 0x00008000 /* UIC3 non-critical interrupt */ -#define UIC_UIC3C 0x00004000 /* UIC3 critical interrupt */ -#define UIC_EIR1 0x00002000 /* External interrupt 1 */ -#define UIC_TRNGDA 0x00001000 /* TRNG data available */ -#define UIC_PKAR1 0x00000800 /* PKA ready (PKA[1]) */ -#define UIC_D1CPFF 0x00000400 /* DMA1 cp fifo full */ -#define UIC_D1CSNS 0x00000200 /* DMA1 cs fifo needs service */ -#define UIC_I2OID 0x00000100 /* I2O inbound door bell */ -#define UIC_I2OLNE 0x00000080 /* I2O Inbound Post List FIFO Not Empty */ -#define UIC_I20R0LL 0x00000040 /* I2O Region 0 Low Latency PLB Write */ -#define UIC_I2OR1LL 0x00000020 /* I2O Region 1 Low Latency PLB Write */ -#define UIC_I20R0HB 0x00000010 /* I2O Region 0 High Bandwidth PLB Write */ -#define UIC_I2OR1HB 0x00000008 /* I2O Region 1 High Bandwidth PLB Write */ -#define UIC_EIP94 0x00000004 /* Security EIP94 */ -#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ -#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ - -#elif !defined(CONFIG_440SPE) -#define UIC_U0 0x80000000 /* UART 0 */ -#define UIC_U1 0x40000000 /* UART 1 */ -#define UIC_IIC0 0x20000000 /* IIC */ -#define UIC_IIC1 0x10000000 /* IIC */ -#define UIC_PIM 0x08000000 /* PCI inbound message */ -#define UIC_PCRW 0x04000000 /* PCI command register write */ -#define UIC_PPM 0x02000000 /* PCI power management */ -#define UIC_MSI0 0x01000000 /* PCI MSI level 0 */ -#define UIC_MSI1 0x00800000 /* PCI MSI level 1 */ -#define UIC_MSI2 0x00400000 /* PCI MSI level 2 */ -#define UIC_MTE 0x00200000 /* MAL TXEOB */ -#define UIC_MRE 0x00100000 /* MAL RXEOB */ -#define UIC_D0 0x00080000 /* DMA channel 0 */ -#define UIC_D1 0x00040000 /* DMA channel 1 */ -#define UIC_D2 0x00020000 /* DMA channel 2 */ -#define UIC_D3 0x00010000 /* DMA channel 3 */ -#define UIC_RSVD0 0x00008000 /* Reserved */ -#define UIC_RSVD1 0x00004000 /* Reserved */ -#define UIC_CT0 0x00002000 /* GPT compare timer 0 */ -#define UIC_CT1 0x00001000 /* GPT compare timer 1 */ -#define UIC_CT2 0x00000800 /* GPT compare timer 2 */ -#define UIC_CT3 0x00000400 /* GPT compare timer 3 */ -#define UIC_CT4 0x00000200 /* GPT compare timer 4 */ -#define UIC_EIR0 0x00000100 /* External interrupt 0 */ -#define UIC_EIR1 0x00000080 /* External interrupt 1 */ -#define UIC_EIR2 0x00000040 /* External interrupt 2 */ -#define UIC_EIR3 0x00000020 /* External interrupt 3 */ -#define UIC_EIR4 0x00000010 /* External interrupt 4 */ -#define UIC_EIR5 0x00000008 /* External interrupt 5 */ -#define UIC_EIR6 0x00000004 /* External interrupt 6 */ -#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ -#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ -#endif /* CONFIG_440GX */ - -/* For compatibility with 405 code */ -#define UIC_MAL_TXEOB UIC_MTE -#define UIC_MAL_RXEOB UIC_MRE - -/*---------------------------------------------------------------------------+ -| Universal interrupt controller 1 interrupts (UIC1) -+---------------------------------------------------------------------------*/ -#if defined(CONFIG_440SP) -#define UIC_EIR0 0x80000000 /* External interrupt 0 */ -#define UIC_MS 0x40000000 /* MAL SERR */ -#define UIC_MTDE 0x20000000 /* MAL TXDE */ -#define UIC_MRDE 0x10000000 /* MAL RXDE */ -#define UIC_DECE 0x08000000 /* DDR SDRAM correctible error */ -#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ -#define UIC_MTE 0x02000000 /* MAL TXEOB */ -#define UIC_MRE 0x01000000 /* MAL RXEOB */ -#define UIC_P0MSI1 0x00800000 /* PCI0 MSI level 1 */ -#define UIC_P1MSI1 0x00400000 /* PCI1 MSI level 1 */ -#define UIC_P2MSI1 0x00200000 /* PCI2 MSI level 1 */ -#define UIC_L2C 0x00100000 /* L2 cache */ -#define UIC_CT0 0x00080000 /* GPT compare timer 0 */ -#define UIC_CT1 0x00040000 /* GPT compare timer 1 */ -#define UIC_CT2 0x00020000 /* GPT compare timer 2 */ -#define UIC_CT3 0x00010000 /* GPT compare timer 3 */ -#define UIC_CT4 0x00008000 /* GPT compare timer 4 */ -#define UIC_EIR1 0x00004000 /* External interrupt 1 */ -#define UIC_EIR2 0x00002000 /* External interrupt 2 */ -#define UIC_EIR3 0x00001000 /* External interrupt 3 */ -#define UIC_EIR4 0x00000800 /* External interrupt 4 */ -#define UIC_EIR5 0x00000400 /* External interrupt 5 */ -#define UIC_DMAE 0x00000200 /* DMA error */ -#define UIC_I2OE 0x00000100 /* I2O error */ -#define UIC_SRE 0x00000080 /* Serial ROM error */ -#define UIC_P0AE 0x00000040 /* PCI0 asynchronous error */ -#define UIC_P1AE 0x00000020 /* PCI1 asynchronous error */ -#define UIC_P2AE 0x00000010 /* PCI2 asynchronous error */ -#define UIC_ETH0 0x00000008 /* Ethernet 0 */ -#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ -#define UIC_ETH1 0x00000002 /* Reserved */ -#define UIC_XOR 0x00000001 /* XOR */ -#elif defined(CONFIG_440GX) || defined(CONFIG_440EP) -#define UIC_MS 0x80000000 /* MAL SERR */ -#define UIC_MTDE 0x40000000 /* MAL TXDE */ -#define UIC_MRDE 0x20000000 /* MAL RXDE */ -#define UIC_DEUE 0x10000000 /* DDR SDRAM ECC uncorrectible error*/ -#define UIC_DECE 0x08000000 /* DDR SDRAM correctible error */ -#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ -#define UIC_EBMI 0x02000000 /* EBMI interrupt status */ -#define UIC_OPB 0x01000000 /* OPB to PLB bridge interrupt stat */ -#define UIC_MSI3 0x00800000 /* PCI MSI level 3 */ -#define UIC_MSI4 0x00400000 /* PCI MSI level 4 */ -#define UIC_MSI5 0x00200000 /* PCI MSI level 5 */ -#define UIC_MSI6 0x00100000 /* PCI MSI level 6 */ -#define UIC_MSI7 0x00080000 /* PCI MSI level 7 */ -#define UIC_MSI8 0x00040000 /* PCI MSI level 8 */ -#define UIC_MSI9 0x00020000 /* PCI MSI level 9 */ -#define UIC_MSI10 0x00010000 /* PCI MSI level 10 */ -#define UIC_MSI11 0x00008000 /* PCI MSI level 11 */ -#define UIC_PPMI 0x00004000 /* PPM interrupt status */ -#define UIC_EIR7 0x00002000 /* External interrupt 7 */ -#define UIC_EIR8 0x00001000 /* External interrupt 8 */ -#define UIC_EIR9 0x00000800 /* External interrupt 9 */ -#define UIC_EIR10 0x00000400 /* External interrupt 10 */ -#define UIC_EIR11 0x00000200 /* External interrupt 11 */ -#define UIC_EIR12 0x00000100 /* External interrupt 12 */ -#define UIC_SRE 0x00000080 /* Serial ROM error */ -#define UIC_RSVD2 0x00000040 /* Reserved */ -#define UIC_RSVD3 0x00000020 /* Reserved */ -#define UIC_PAE 0x00000010 /* PCI asynchronous error */ -#define UIC_ETH0 0x00000008 /* Ethernet 0 */ -#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ -#define UIC_ETH1 0x00000002 /* Ethernet 1 */ -#define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */ - -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) - -#define UIC_EIR2 0x80000000 /* External interrupt 2 */ -#define UIC_U0 0x40000000 /* UART 0 */ -#define UIC_SPI 0x20000000 /* SPI */ -#define UIC_TRNGAL 0x10000000 /* TRNG alarm */ -#define UIC_DEUE 0x08000000 /* DDR SDRAM ECC correct/uncorrectable error */ -#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ -#define UIC_NDFC 0x02000000 /* NDFC */ -#define UIC_EIPPKPSE 0x01000000 /* EIPPKP slave error */ -#define UIC_P0MSI1 0x00800000 /* PCI0 MSI level 1 */ -#define UIC_P0MSI2 0x00400000 /* PCI0 MSI level 2 */ -#define UIC_P0MSI3 0x00200000 /* PCI0 MSI level 3 */ -#define UIC_L2C 0x00100000 /* L2 cache */ -#define UIC_CT0 0x00080000 /* GPT compare timer 0 */ -#define UIC_CT1 0x00040000 /* GPT compare timer 1 */ -#define UIC_CT2 0x00020000 /* GPT compare timer 2 */ -#define UIC_CT3 0x00010000 /* GPT compare timer 3 */ -#define UIC_CT4 0x00008000 /* GPT compare timer 4 */ -#define UIC_CT5 0x00004000 /* GPT compare timer 5 */ -#define UIC_CT6 0x00002000 /* GPT compare timer 6 */ -#define UIC_GPTDC 0x00001000 /* GPT decrementer pulse */ -#define UIC_EIR3 0x00000800 /* External interrupt 3 */ -#define UIC_EIR4 0x00000400 /* External interrupt 4 */ -#define UIC_DMAE 0x00000200 /* DMA error */ -#define UIC_I2OE 0x00000100 /* I2O error */ -#define UIC_SRE 0x00000080 /* Serial ROM error */ -#define UIC_P0AE 0x00000040 /* PCI0 asynchronous error */ -#define UIC_EIR5 0x00000020 /* External interrupt 5 */ -#define UIC_EIR6 0x00000010 /* External interrupt 6 */ -#define UIC_U2 0x00000008 /* UART 2 */ -#define UIC_U3 0x00000004 /* UART 3 */ -#define UIC_EIR7 0x00000002 /* External interrupt 7 */ -#define UIC_EIR8 0x00000001 /* External interrupt 8 */ - -#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) - -#define UIC_MS 0x80000000 /* MAL SERR */ -#define UIC_MTDE 0x40000000 /* MAL TXDE */ -#define UIC_MRDE 0x20000000 /* MAL RXDE */ -#define UIC_U2 0x10000000 /* UART 2 */ -#define UIC_U3 0x08000000 /* UART 3 */ -#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ -#define UIC_NDFC 0x02000000 /* NDFC */ -#define UIC_KSLE 0x01000000 /* KASUMI slave error */ -#define UIC_CT5 0x00800000 /* GPT compare timer 5 */ -#define UIC_CT6 0x00400000 /* GPT compare timer 6 */ -#define UIC_PLB34I0 0x00200000 /* PLB3X4X MIRQ0 */ -#define UIC_PLB34I1 0x00100000 /* PLB3X4X MIRQ1 */ -#define UIC_PLB34I2 0x00080000 /* PLB3X4X MIRQ2 */ -#define UIC_PLB34I3 0x00040000 /* PLB3X4X MIRQ3 */ -#define UIC_PLB34I4 0x00020000 /* PLB3X4X MIRQ4 */ -#define UIC_PLB34I5 0x00010000 /* PLB3X4X MIRQ5 */ -#define UIC_CT0 0x00008000 /* GPT compare timer 0 */ -#define UIC_CT1 0x00004000 /* GPT compare timer 1 */ -#define UIC_EIR7 0x00002000 /* External interrupt 7 */ -#define UIC_EIR8 0x00001000 /* External interrupt 8 */ -#define UIC_EIR9 0x00000800 /* External interrupt 9 */ -#define UIC_CT2 0x00000400 /* GPT compare timer 2 */ -#define UIC_CT3 0x00000200 /* GPT compare timer 3 */ -#define UIC_CT4 0x00000100 /* GPT compare timer 4 */ -#define UIC_SRE 0x00000080 /* Serial ROM error */ -#define UIC_GPTDC 0x00000040 /* GPT decrementer pulse */ -#define UIC_RSVD0 0x00000020 /* Reserved */ -#define UIC_EPCIPER 0x00000010 /* External PCI PERR */ -#define UIC_EIR0 0x00000008 /* External interrupt 0 */ -#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ -#define UIC_EIR1 0x00000002 /* External interrupt 1 */ -#define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */ - -/* For compatibility with 405 code */ -#define UIC_MAL_SERR UIC_MS -#define UIC_MAL_TXDE UIC_MTDE -#define UIC_MAL_RXDE UIC_MRDE -#define UIC_ENET UIC_ETH0 - -#elif !defined(CONFIG_440SPE) -#define UIC_MS 0x80000000 /* MAL SERR */ -#define UIC_MTDE 0x40000000 /* MAL TXDE */ -#define UIC_MRDE 0x20000000 /* MAL RXDE */ -#define UIC_DEUE 0x10000000 /* DDR SDRAM ECC uncorrectible error*/ -#define UIC_DECE 0x08000000 /* DDR SDRAM correctible error */ -#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ -#define UIC_EBMI 0x02000000 /* EBMI interrupt status */ -#define UIC_OPB 0x01000000 /* OPB to PLB bridge interrupt stat */ -#define UIC_MSI3 0x00800000 /* PCI MSI level 3 */ -#define UIC_MSI4 0x00400000 /* PCI MSI level 4 */ -#define UIC_MSI5 0x00200000 /* PCI MSI level 5 */ -#define UIC_MSI6 0x00100000 /* PCI MSI level 6 */ -#define UIC_MSI7 0x00080000 /* PCI MSI level 7 */ -#define UIC_MSI8 0x00040000 /* PCI MSI level 8 */ -#define UIC_MSI9 0x00020000 /* PCI MSI level 9 */ -#define UIC_MSI10 0x00010000 /* PCI MSI level 10 */ -#define UIC_MSI11 0x00008000 /* PCI MSI level 11 */ -#define UIC_PPMI 0x00004000 /* PPM interrupt status */ -#define UIC_EIR7 0x00002000 /* External interrupt 7 */ -#define UIC_EIR8 0x00001000 /* External interrupt 8 */ -#define UIC_EIR9 0x00000800 /* External interrupt 9 */ -#define UIC_EIR10 0x00000400 /* External interrupt 10 */ -#define UIC_EIR11 0x00000200 /* External interrupt 11 */ -#define UIC_EIR12 0x00000100 /* External interrupt 12 */ -#define UIC_SRE 0x00000080 /* Serial ROM error */ -#define UIC_RSVD2 0x00000040 /* Reserved */ -#define UIC_RSVD3 0x00000020 /* Reserved */ -#define UIC_PAE 0x00000010 /* PCI asynchronous error */ -#define UIC_ETH0 0x00000008 /* Ethernet 0 */ -#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ -#define UIC_ETH1 0x00000002 /* Ethernet 1 */ -#define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */ -#endif /* CONFIG_440SP */ - -/* For compatibility with 405 code */ -#define UIC_MAL_SERR UIC_MS -#define UIC_MAL_TXDE UIC_MTDE -#define UIC_MAL_RXDE UIC_MRDE -#define UIC_ENET UIC_ETH0 - -/*---------------------------------------------------------------------------+ -| Universal interrupt controller 2 interrupts (UIC2) -+---------------------------------------------------------------------------*/ -#if defined(CONFIG_440GX) -#define UIC_ETH2 0x80000000 /* Ethernet 2 */ -#define UIC_EWU2 0x40000000 /* Ethernet 2 wakeup */ -#define UIC_ETH3 0x20000000 /* Ethernet 3 */ -#define UIC_EWU3 0x10000000 /* Ethernet 3 wakeup */ -#define UIC_TAH0 0x08000000 /* TAH 0 */ -#define UIC_TAH1 0x04000000 /* TAH 1 */ -#define UIC_IMUOBFQ 0x02000000 /* IMU outbound free queue */ -#define UIC_IMUIBPQ 0x01000000 /* IMU inbound post queue */ -#define UIC_IMUIRQDB 0x00800000 /* IMU irq doorbell */ -#define UIC_IMUIBDB 0x00400000 /* IMU inbound doorbell */ -#define UIC_IMUMSG0 0x00200000 /* IMU inbound message 0 */ -#define UIC_IMUMSG1 0x00100000 /* IMU inbound message 1 */ -#define UIC_IMUTO 0x00080000 /* IMU timeout */ -#define UIC_MSI12 0x00040000 /* PCI MSI level 12 */ -#define UIC_MSI13 0x00020000 /* PCI MSI level 13 */ -#define UIC_MSI14 0x00010000 /* PCI MSI level 14 */ -#define UIC_MSI15 0x00008000 /* PCI MSI level 15 */ -#define UIC_EIR13 0x00004000 /* External interrupt 13 */ -#define UIC_EIR14 0x00002000 /* External interrupt 14 */ -#define UIC_EIR15 0x00001000 /* External interrupt 15 */ -#define UIC_EIR16 0x00000800 /* External interrupt 16 */ -#define UIC_EIR17 0x00000400 /* External interrupt 17 */ -#define UIC_PCIVPD 0x00000200 /* PCI VPD */ -#define UIC_L2C 0x00000100 /* L2 Cache */ -#define UIC_ETH2PCS 0x00000080 /* Ethernet 2 PCS */ -#define UIC_ETH3PCS 0x00000040 /* Ethernet 3 PCS */ -#define UIC_RSVD26 0x00000020 /* Reserved */ -#define UIC_RSVD27 0x00000010 /* Reserved */ -#define UIC_RSVD28 0x00000008 /* Reserved */ -#define UIC_RSVD29 0x00000004 /* Reserved */ -#define UIC_RSVD30 0x00000002 /* Reserved */ -#define UIC_RSVD31 0x00000001 /* Reserved */ - -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) - -#define UIC_TAH0 0x80000000 /* TAHOE 0 */ -#define UIC_TAH1 0x40000000 /* TAHOE 1 */ -#define UIC_EIR9 0x20000000 /* External interrupt 9 */ -#define UIC_MS 0x10000000 /* MAL SERR */ -#define UIC_MTDE 0x08000000 /* MAL TXDE */ -#define UIC_MRDE 0x04000000 /* MAL RXDE */ -#define UIC_MTE 0x02000000 /* MAL TXEOB */ -#define UIC_MRE 0x01000000 /* MAL RXEOB */ -#define UIC_MCTX0 0x00800000 /* MAL interrupt coalescence TX0 */ -#define UIC_MCTX1 0x00400000 /* MAL interrupt coalescence TX1 */ -#define UIC_MCTX2 0x00200000 /* MAL interrupt coalescence TX2 */ -#define UIC_MCTX3 0x00100000 /* MAL interrupt coalescence TX3 */ -#define UIC_MCTR0 0x00080000 /* MAL interrupt coalescence TR0 */ -#define UIC_MCTR1 0x00040000 /* MAL interrupt coalescence TR1 */ -#define UIC_MCTR2 0x00020000 /* MAL interrupt coalescence TR2 */ -#define UIC_MCTR3 0x00010000 /* MAL interrupt coalescence TR3 */ -#define UIC_ETH0 0x00008000 /* Ethernet 0 */ -#define UIC_ETH1 0x00004000 /* Ethernet 1 */ -#define UIC_ETH2 0x00002000 /* Ethernet 2 */ -#define UIC_ETH3 0x00001000 /* Ethernet 3 */ -#define UIC_EWU0 0x00000800 /* Ethernet 0 wakeup */ -#define UIC_EWU1 0x00000400 /* Ethernet 1 wakeup */ -#define UIC_EWU2 0x00000200 /* Ethernet 2 wakeup */ -#define UIC_EWU3 0x00000100 /* Ethernet 3 wakeup */ -#define UIC_EIR10 0x00000080 /* External interrupt 10 */ -#define UIC_EIR11 0x00000040 /* External interrupt 11 */ -#define UIC_RSVD2 0x00000020 /* Reserved */ -#define UIC_PLB4XAHB 0x00000010 /* PLB4XAHB / AHBARB error */ -#define UIC_OTG 0x00000008 /* USB2.0 OTG */ -#define UIC_EHCI 0x00000004 /* USB2.0 Host EHCI */ -#define UIC_OHCI 0x00000002 /* USB2.0 Host OHCI */ -#define UIC_OHCISMI 0x00000001 /* USB2.0 Host OHCI SMI */ - -#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* UIC2 */ - -#define UIC_EIR5 0x80000000 /* External interrupt 5 */ -#define UIC_EIR6 0x40000000 /* External interrupt 6 */ -#define UIC_OPB 0x20000000 /* OPB to PLB bridge interrupt stat */ -#define UIC_EIR2 0x10000000 /* External interrupt 2 */ -#define UIC_EIR3 0x08000000 /* External interrupt 3 */ -#define UIC_DDR2 0x04000000 /* DDR2 sdram */ -#define UIC_MCTX0 0x02000000 /* MAl intp coalescence TX0 */ -#define UIC_MCTX1 0x01000000 /* MAl intp coalescence TX1 */ -#define UIC_MCTR0 0x00800000 /* MAl intp coalescence TR0 */ -#define UIC_MCTR1 0x00400000 /* MAl intp coalescence TR1 */ - -#endif /* CONFIG_440GX */ - -/*---------------------------------------------------------------------------+ -| Universal interrupt controller Base 0 interrupts (UICB0) -+---------------------------------------------------------------------------*/ -#if defined(CONFIG_440GX) -#define UICB0_UIC0CI 0x80000000 /* UIC0 Critical Interrupt */ -#define UICB0_UIC0NCI 0x40000000 /* UIC0 Noncritical Interrupt */ -#define UICB0_UIC1CI 0x20000000 /* UIC1 Critical Interrupt */ -#define UICB0_UIC1NCI 0x10000000 /* UIC1 Noncritical Interrupt */ -#define UICB0_UIC2CI 0x08000000 /* UIC2 Critical Interrupt */ -#define UICB0_UIC2NCI 0x04000000 /* UIC2 Noncritical Interrupt */ - -#define UICB0_ALL (UICB0_UIC0CI | UICB0_UIC0NCI | UICB0_UIC1CI | \ - UICB0_UIC1NCI | UICB0_UIC2CI | UICB0_UIC2NCI) - -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) - -#define UICB0_UIC1NCI 0x00000002 /* UIC1 Noncritical Interrupt */ -#define UICB0_UIC1CI 0x00000001 /* UIC1 Critical Interrupt */ -#define UICB0_UIC2NCI 0x00200000 /* UIC2 Noncritical Interrupt */ -#define UICB0_UIC2CI 0x00100000 /* UIC2 Critical Interrupt */ -#define UICB0_UIC3NCI 0x00008000 /* UIC3 Noncritical Interrupt */ -#define UICB0_UIC3CI 0x00004000 /* UIC3 Critical Interrupt */ - -#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI | UICB0_UIC2CI | \ - UICB0_UIC2NCI | UICB0_UIC3CI | UICB0_UIC3NCI) - -#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) - -#define UICB0_UIC1CI 0x00000001 /* UIC1 Critical Interrupt */ -#define UICB0_UIC1NCI 0x00000002 /* UIC1 Noncritical Interrupt */ -#define UICB0_UIC2CI 0x00000004 /* UIC2 Critical Interrupt */ -#define UICB0_UIC2NCI 0x00000008 /* UIC2 Noncritical Interrupt */ - -#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI | \ - UICB0_UIC1CI | UICB0_UIC2NCI) - -#elif defined(CONFIG_440GP) || defined(CONFIG_440SP) || \ - defined(CONFIG_440EP) || defined(CONFIG_440GR) - -#define UICB0_UIC1CI 0x00000001 /* UIC1 Critical Interrupt */ -#define UICB0_UIC1NCI 0x00000002 /* UIC1 Noncritical Interrupt */ - -#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI) - -#endif /* CONFIG_440GX */ -/*---------------------------------------------------------------------------+ -| Universal interrupt controller interrupts -+---------------------------------------------------------------------------*/ -#if defined(CONFIG_440SPE) -/*#define UICB0_UIC0CI 0x80000000*/ /* UIC0 Critical Interrupt */ -/*#define UICB0_UIC0NCI 0x40000000*/ /* UIC0 Noncritical Interrupt */ -#define UICB0_UIC1CI 0x00000002 /* UIC1 Critical Interrupt */ -#define UICB0_UIC1NCI 0x00000001 /* UIC1 Noncritical Interrupt */ -#define UICB0_UIC2CI 0x00200000 /* UIC2 Critical Interrupt */ -#define UICB0_UIC2NCI 0x00100000 /* UIC2 Noncritical Interrupt */ -#define UICB0_UIC3CI 0x00008000 /* UIC3 Critical Interrupt */ -#define UICB0_UIC3NCI 0x00004000 /* UIC3 Noncritical Interrupt */ - -#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI | UICB0_UIC2CI | \ - UICB0_UIC2NCI | UICB0_UIC3CI | UICB0_UIC3NCI) -/*---------------------------------------------------------------------------+ -| Universal interrupt controller 0 interrupts (UIC0) -+---------------------------------------------------------------------------*/ -#define UIC_U0 0x80000000 /* UART 0 */ -#define UIC_U1 0x40000000 /* UART 1 */ -#define UIC_IIC0 0x20000000 /* IIC */ -#define UIC_IIC1 0x10000000 /* IIC */ -#define UIC_PIM 0x08000000 /* PCI inbound message */ -#define UIC_PCRW 0x04000000 /* PCI command register write */ -#define UIC_PPM 0x02000000 /* PCI power management */ -#define UIC_PVPDA 0x01000000 /* PCIx 0 vpd access */ -#define UIC_MSI0 0x00800000 /* PCIx MSI level 0 */ -#define UIC_EIR15 0x00400000 /* External intp 15 */ -#define UIC_PEMSI0 0x00080000 /* PCIe MSI level 0 */ -#define UIC_PEMSI1 0x00040000 /* PCIe MSI level 1 */ -#define UIC_PEMSI2 0x00020000 /* PCIe MSI level 2 */ -#define UIC_PEMSI3 0x00010000 /* PCIe MSI level 3 */ -#define UIC_EIR14 0x00002000 /* External interrupt 14 */ -#define UIC_D0CPFF 0x00001000 /* DMA0 cp fifo full */ -#define UIC_D0CSNS 0x00000800 /* DMA0 cs fifo needs service */ -#define UIC_D1CPFF 0x00000400 /* DMA1 cp fifo full */ -#define UIC_D1CSNS 0x00000200 /* DMA1 cs fifo needs service */ -#define UIC_I2OID 0x00000100 /* I2O inbound door bell */ -#define UIC_I2OLNE 0x00000080 /* I2O Inbound Post List FIFO Not Empty */ -#define UIC_I20R0LL 0x00000040 /* I2O Region 0 Low Latency PLB Write */ -#define UIC_I2OR1LL 0x00000020 /* I2O Region 1 Low Latency PLB Write */ -#define UIC_I20R0HB 0x00000010 /* I2O Region 0 High Bandwidth PLB Write */ -#define UIC_I2OR1HB 0x00000008 /* I2O Region 1 High Bandwidth PLB Write */ -#define UIC_CPTCNT 0x00000004 /* GPT Count Timer */ -/*---------------------------------------------------------------------------+ -| Universal interrupt controller 1 interrupts (UIC1) -+---------------------------------------------------------------------------*/ -#define UIC_EIR13 0x80000000 /* externei intp 13 */ -#define UIC_MS 0x40000000 /* MAL SERR */ -#define UIC_MTDE 0x20000000 /* MAL TXDE */ -#define UIC_MRDE 0x10000000 /* MAL RXDE */ -#define UIC_DEUE 0x08000000 /* DDR SDRAM ECC correct/uncorrectable error */ -#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ -#define UIC_MTE 0x02000000 /* MAL TXEOB */ -#define UIC_MRE 0x01000000 /* MAL RXEOB */ -#define UIC_MSI1 0x00800000 /* PCI MSI level 1 */ -#define UIC_MSI2 0x00400000 /* PCI MSI level 2 */ -#define UIC_MSI3 0x00200000 /* PCI MSI level 3 */ -#define UIC_L2C 0x00100000 /* L2 cache */ -#define UIC_CT0 0x00080000 /* GPT compare timer 0 */ -#define UIC_CT1 0x00040000 /* GPT compare timer 1 */ -#define UIC_CT2 0x00020000 /* GPT compare timer 2 */ -#define UIC_CT3 0x00010000 /* GPT compare timer 3 */ -#define UIC_CT4 0x00008000 /* GPT compare timer 4 */ -#define UIC_EIR12 0x00004000 /* External interrupt 12 */ -#define UIC_EIR11 0x00002000 /* External interrupt 11 */ -#define UIC_EIR10 0x00001000 /* External interrupt 10 */ -#define UIC_EIR9 0x00000800 /* External interrupt 9 */ -#define UIC_EIR8 0x00000400 /* External interrupt 8 */ -#define UIC_DMAE 0x00000200 /* dma error */ -#define UIC_I2OE 0x00000100 /* i2o error */ -#define UIC_SRE 0x00000080 /* Serial ROM error */ -#define UIC_PCIXAE 0x00000040 /* Pcix0 async error */ -#define UIC_EIR7 0x00000020 /* External interrupt 7 */ -#define UIC_EIR6 0x00000010 /* External interrupt 6 */ -#define UIC_ETH0 0x00000008 /* Ethernet 0 */ -#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ -#define UIC_ETH1 0x00000002 /* reserved */ -#define UIC_XOR 0x00000001 /* xor */ - -/*---------------------------------------------------------------------------+ -| Universal interrupt controller 2 interrupts (UIC2) -+---------------------------------------------------------------------------*/ -#define UIC_PEOAL 0x80000000 /* PE0 AL */ -#define UIC_PEOVA 0x40000000 /* PE0 VPD access */ -#define UIC_PEOHRR 0x20000000 /* PE0 Host reset request rising */ -#define UIC_PE0HRF 0x10000000 /* PE0 Host reset request falling */ -#define UIC_PE0TCR 0x08000000 /* PE0 TCR */ -#define UIC_PE0BVCO 0x04000000 /* PE0 Busmaster VCO */ -#define UIC_PE0DCRE 0x02000000 /* PE0 DCR error */ -#define UIC_PE1AL 0x00800000 /* PE1 AL */ -#define UIC_PE1VA 0x00400000 /* PE1 VPD access */ -#define UIC_PE1HRR 0x00200000 /* PE1 Host reset request rising */ -#define UIC_PE1HRF 0x00100000 /* PE1 Host reset request falling */ -#define UIC_PE1TCR 0x00080000 /* PE1 TCR */ -#define UIC_PE1BVCO 0x00040000 /* PE1 Busmaster VCO */ -#define UIC_PE1DCRE 0x00020000 /* PE1 DCR error */ -#define UIC_PE2AL 0x00008000 /* PE2 AL */ -#define UIC_PE2VA 0x00004000 /* PE2 VPD access */ -#define UIC_PE2HRR 0x00002000 /* PE2 Host reset request rising */ -#define UIC_PE2HRF 0x00001000 /* PE2 Host reset request falling */ -#define UIC_PE2TCR 0x00000800 /* PE2 TCR */ -#define UIC_PE2BVCO 0x00000400 /* PE2 Busmaster VCO */ -#define UIC_PE2DCRE 0x00000200 /* PE2 DCR error */ -#define UIC_EIR5 0x00000080 /* External interrupt 5 */ -#define UIC_EIR4 0x00000040 /* External interrupt 4 */ -#define UIC_EIR3 0x00000020 /* External interrupt 3 */ -#define UIC_EIR2 0x00000010 /* External interrupt 2 */ -#define UIC_EIR1 0x00000008 /* External interrupt 1 */ -#define UIC_EIR0 0x00000004 /* External interrupt 0 */ -#endif /* CONFIG_440SPE */ - -/*-----------------------------------------------------------------------------+ -| External Bus Controller Bit Settings -+-----------------------------------------------------------------------------*/ -#define EBC_CFGADDR_MASK 0x0000003F - -#define EBC_BXCR_BAS_ENCODE(n) ((((unsigned long)(n))&0xFFF00000)<<0) -#define EBC_BXCR_BS_MASK 0x000E0000 -#define EBC_BXCR_BS_1MB 0x00000000 -#define EBC_BXCR_BS_2MB 0x00020000 -#define EBC_BXCR_BS_4MB 0x00040000 -#define EBC_BXCR_BS_8MB 0x00060000 -#define EBC_BXCR_BS_16MB 0x00080000 -#define EBC_BXCR_BS_32MB 0x000A0000 -#define EBC_BXCR_BS_64MB 0x000C0000 -#define EBC_BXCR_BS_128MB 0x000E0000 -#define EBC_BXCR_BU_MASK 0x00018000 -#define EBC_BXCR_BU_R 0x00008000 -#define EBC_BXCR_BU_W 0x00010000 -#define EBC_BXCR_BU_RW 0x00018000 -#define EBC_BXCR_BW_MASK 0x00006000 -#define EBC_BXCR_BW_8BIT 0x00000000 -#define EBC_BXCR_BW_16BIT 0x00002000 -#define EBC_BXCR_BW_32BIT 0x00006000 -#define EBC_BXAP_BME_ENABLED 0x80000000 -#define EBC_BXAP_BME_DISABLED 0x00000000 -#define EBC_BXAP_TWT_ENCODE(n) ((((unsigned long)(n))&0xFF)<<23) -#define EBC_BXAP_BCE_DISABLE 0x00000000 -#define EBC_BXAP_BCE_ENABLE 0x00400000 -#define EBC_BXAP_BCT_MASK 0x00300000 -#define EBC_BXAP_BCT_2TRANS 0x00000000 -#define EBC_BXAP_BCT_4TRANS 0x00100000 -#define EBC_BXAP_BCT_8TRANS 0x00200000 -#define EBC_BXAP_BCT_16TRANS 0x00300000 -#define EBC_BXAP_CSN_ENCODE(n) ((((unsigned long)(n))&0x3)<<18) -#define EBC_BXAP_OEN_ENCODE(n) ((((unsigned long)(n))&0x3)<<16) -#define EBC_BXAP_WBN_ENCODE(n) ((((unsigned long)(n))&0x3)<<14) -#define EBC_BXAP_WBF_ENCODE(n) ((((unsigned long)(n))&0x3)<<12) -#define EBC_BXAP_TH_ENCODE(n) ((((unsigned long)(n))&0x7)<<9) -#define EBC_BXAP_RE_ENABLED 0x00000100 -#define EBC_BXAP_RE_DISABLED 0x00000000 -#define EBC_BXAP_SOR_DELAYED 0x00000000 -#define EBC_BXAP_SOR_NONDELAYED 0x00000080 -#define EBC_BXAP_BEM_WRITEONLY 0x00000000 -#define EBC_BXAP_BEM_RW 0x00000040 -#define EBC_BXAP_PEN_DISABLED 0x00000000 - -#define EBC_CFG_LE_MASK 0x80000000 -#define EBC_CFG_LE_UNLOCK 0x00000000 -#define EBC_CFG_LE_LOCK 0x80000000 -#define EBC_CFG_PTD_MASK 0x40000000 -#define EBC_CFG_PTD_ENABLE 0x00000000 -#define EBC_CFG_PTD_DISABLE 0x40000000 -#define EBC_CFG_RTC_MASK 0x38000000 -#define EBC_CFG_RTC_16PERCLK 0x00000000 -#define EBC_CFG_RTC_32PERCLK 0x08000000 -#define EBC_CFG_RTC_64PERCLK 0x10000000 -#define EBC_CFG_RTC_128PERCLK 0x18000000 -#define EBC_CFG_RTC_256PERCLK 0x20000000 -#define EBC_CFG_RTC_512PERCLK 0x28000000 -#define EBC_CFG_RTC_1024PERCLK 0x30000000 -#define EBC_CFG_RTC_2048PERCLK 0x38000000 -#define EBC_CFG_ATC_MASK 0x04000000 -#define EBC_CFG_ATC_HI 0x00000000 -#define EBC_CFG_ATC_PREVIOUS 0x04000000 -#define EBC_CFG_DTC_MASK 0x02000000 -#define EBC_CFG_DTC_HI 0x00000000 -#define EBC_CFG_DTC_PREVIOUS 0x02000000 -#define EBC_CFG_CTC_MASK 0x01000000 -#define EBC_CFG_CTC_HI 0x00000000 -#define EBC_CFG_CTC_PREVIOUS 0x01000000 -#define EBC_CFG_OEO_MASK 0x00800000 -#define EBC_CFG_OEO_HI 0x00000000 -#define EBC_CFG_OEO_PREVIOUS 0x00800000 -#define EBC_CFG_EMC_MASK 0x00400000 -#define EBC_CFG_EMC_NONDEFAULT 0x00000000 -#define EBC_CFG_EMC_DEFAULT 0x00400000 -#define EBC_CFG_PME_MASK 0x00200000 -#define EBC_CFG_PME_DISABLE 0x00000000 -#define EBC_CFG_PME_ENABLE 0x00200000 -#define EBC_CFG_PMT_MASK 0x001F0000 -#define EBC_CFG_PMT_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12) -#define EBC_CFG_PR_MASK 0x0000C000 -#define EBC_CFG_PR_16 0x00000000 -#define EBC_CFG_PR_32 0x00004000 -#define EBC_CFG_PR_64 0x00008000 -#define EBC_CFG_PR_128 0x0000C000 - /*-----------------------------------------------------------------------------+ | SDR0 Bit Settings +-----------------------------------------------------------------------------*/ @@ -1855,7 +887,7 @@ #define SDR0_DDR0_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x2FF) #endif -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_460SX) #define SDR0_CP440 0x0180 #define SDR0_CP440_ERPN_MASK 0x30000000 #define SDR0_CP440_ERPN_MASK_HI 0x3000 @@ -2793,7 +1825,8 @@ /*-----------------------------------------------------------------------------+ | Clocking +-----------------------------------------------------------------------------*/ -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) #define PLLSYS0_FWD_DIV_A_MASK 0x000000f0 /* Fwd Div A */ #define PLLSYS0_FWD_DIV_B_MASK 0x0000000f /* Fwd Div B */ #define PLLSYS0_FB_DIV_MASK 0x0000ff00 /* Feedback divisor */ @@ -2873,118 +1906,10 @@ #endif /* CONFIG_440GX */ #if defined (CONFIG_440EPX) || defined (CONFIG_440GRX) -/*--------------------------------------*/ -#define CPR0_PLLC 0x40 -#define CPR0_PLLC_RST_MASK 0x80000000 -#define CPR0_PLLC_RST_PLLLOCKED 0x00000000 -#define CPR0_PLLC_RST_PLLRESET 0x80000000 -#define CPR0_PLLC_ENG_MASK 0x40000000 -#define CPR0_PLLC_ENG_DISABLE 0x00000000 -#define CPR0_PLLC_ENG_ENABLE 0x40000000 -#define CPR0_PLLC_ENG_ENCODE(n) ((((unsigned long)(n))&0x01)<<30) -#define CPR0_PLLC_ENG_DECODE(n) ((((unsigned long)(n))>>30)&0x01) -#define CPR0_PLLC_SRC_MASK 0x20000000 -#define CPR0_PLLC_SRC_PLLOUTA 0x00000000 -#define CPR0_PLLC_SRC_PLLOUTB 0x20000000 -#define CPR0_PLLC_SRC_ENCODE(n) ((((unsigned long)(n))&0x01)<<29) -#define CPR0_PLLC_SRC_DECODE(n) ((((unsigned long)(n))>>29)&0x01) -#define CPR0_PLLC_SEL_MASK 0x07000000 -#define CPR0_PLLC_SEL_PLL 0x00000000 -#define CPR0_PLLC_SEL_CPU 0x01000000 -#define CPR0_PLLC_SEL_PER 0x05000000 -#define CPR0_PLLC_SEL_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) -#define CPR0_PLLC_SEL_DECODE(n) ((((unsigned long)(n))>>24)&0x07) -#define CPR0_PLLC_TUNE_MASK 0x000003FF -#define CPR0_PLLC_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) -#define CPR0_PLLC_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF) -/*--------------------------------------*/ -#define CPR0_PLLD 0x60 -#define CPR0_PLLD_FBDV_MASK 0x1F000000 -#define CPR0_PLLD_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) -#define CPR0_PLLD_FBDV_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x1F)+1) -#define CPR0_PLLD_FWDVA_MASK 0x000F0000 -#define CPR0_PLLD_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<16) -#define CPR0_PLLD_FWDVA_DECODE(n) ((((((unsigned long)(n))>>16)-1)&0x0F)+1) -#define CPR0_PLLD_FWDVB_MASK 0x00000700 -#define CPR0_PLLD_FWDVB_ENCODE(n) ((((unsigned long)(n))&0x07)<<8) -#define CPR0_PLLD_FWDVB_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x07)+1) -#define CPR0_PLLD_LFBDV_MASK 0x0000003F -#define CPR0_PLLD_LFBDV_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0) -#define CPR0_PLLD_LFBDV_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x3F)+1) -/*--------------------------------------*/ -#define CPR0_PRIMAD 0x80 -#define CPR0_PRIMAD_PRADV0_MASK 0x07000000 -#define CPR0_PRIMAD_PRADV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) -#define CPR0_PRIMAD_PRADV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) -/*--------------------------------------*/ -#define CPR0_PRIMBD 0xA0 -#define CPR0_PRIMBD_PRBDV0_MASK 0x07000000 -#define CPR0_PRIMBD_PRBDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) -#define CPR0_PRIMBD_PRBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) -/*--------------------------------------*/ -#if 0 -#define CPR0_CPM0_ER 0xB0 /* CPM Enable Register */ -#define CPR0_CPM0_FR 0xB1 /* CPM Force Register */ -#define CPR0_CPM0_SR 0xB2 /* CPM Status Register */ -#define CPR0_CPM0_IIC0 0x80000000 /* Inter-Intergrated Circuit0 */ -#define CPR0_CPM0_IIC1 0x40000000 /* Inter-Intergrated Circuit1 */ -#define CPR0_CPM0_PCI 0x20000000 /* Peripheral Component Interconnect */ -#define CPR0_CPM0_USB1H 0x08000000 /* USB1.1 Host */ -#define CPR0_CPM0_FPU 0x04000000 /* PPC440 FPU */ -#define CPR0_CPM0_CPU 0x02000000 /* PPC440x5 Processor Core */ -#define CPR0_CPM0_DMA 0x01000000 /* Direct Memory Access Controller */ -#define CPR0_CPM0_BGO 0x00800000 /* PLB to OPB Bridge */ -#define CPR0_CPM0_BGI 0x00400000 /* OPB to PLB Bridge */ -#define CPR0_CPM0_EBC 0x00200000 /* External Bus Controller */ -#define CPR0_CPM0_NDFC 0x00100000 /* Nand Flash Controller */ -#define CPR0_CPM0_MADMAL 0x00080000 /* DDR SDRAM Controller or MADMAL ??? */ -#define CPR0_CPM0_DMC 0x00080000 /* DDR SDRAM Controller or MADMAL ??? */ -#define CPR0_CPM0_PLB4 0x00040000 /* PLB4 Arbiter */ -#define CPR0_CPM0_PLB4x3x 0x00020000 /* PLB4 to PLB3 */ -#define CPR0_CPM0_PLB3x4x 0x00010000 /* PLB3 to PLB4 */ -#define CPR0_CPM0_PLB3 0x00008000 /* PLB3 Arbiter */ -#define CPR0_CPM0_PPM 0x00002000 /* PLB Performance Monitor */ -#define CPR0_CPM0_UIC1 0x00001000 /* Universal Interrupt Controller 1 */ -#define CPR0_CPM0_GPIO 0x00000800 /* General Purpose IO */ -#define CPR0_CPM0_GPT 0x00000400 /* General Purpose Timer */ -#define CPR0_CPM0_UART0 0x00000200 /* Universal Asynchronous Rcver/Xmitter 0 */ -#define CPR0_CPM0_UART1 0x00000100 /* Universal Asynchronous Rcver/Xmitter 1 */ -#define CPR0_CPM0_UIC0 0x00000080 /* Universal Interrupt Controller 0 */ -#define CPR0_CPM0_TMRCLK 0x00000040 /* CPU Timer */ -#define CPR0_CPM0_EMC0 0x00000020 /* Ethernet 0 */ -#define CPR0_CPM0_EMC1 0x00000010 /* Ethernet 1 */ -#define CPR0_CPM0_UART2 0x00000008 /* Universal Asynchronous Rcver/Xmitter 2 */ -#define CPR0_CPM0_UART3 0x00000004 /* Universal Asynchronous Rcver/Xmitter 3 */ -#define CPR0_CPM0_USB2D 0x00000002 /* USB2.0 Device */ -#define CPR0_CPM0_USB2H 0x00000001 /* USB2.0 Host */ +#define CPR0_ICFG_RLI_MASK 0x80000000 +#define CPR0_SPCID_SPCIDV0_MASK 0x03000000 +#define CPR0_PERD_PERDV0_MASK 0x07000000 #endif -/*--------------------------------------*/ -#define CPR0_OPBD 0xC0 -#define CPR0_OPBD_OPBDV0_MASK 0x03000000 -#define CPR0_OPBD_OPBDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) -#define CPR0_OPBD_OPBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) -/*--------------------------------------*/ -#define CPR0_PERD 0xE0 -#define CPR0_PERD_PERDV0_MASK 0x07000000 -#define CPR0_PERD_PERDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) -#define CPR0_PERD_PERDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) -/*--------------------------------------*/ -#define CPR0_MALD 0x100 -#define CPR0_MALD_MALDV0_MASK 0x03000000 -#define CPR0_MALD_MALDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) -#define CPR0_MALD_MALDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) -/*--------------------------------------*/ -#define CPR0_SPCID 0x120 -#define CPR0_SPCID_SPCIDV0_MASK 0x03000000 -#define CPR0_SPCID_SPCIDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) -#define CPR0_SPCID_SPCIDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) -/*--------------------------------------*/ -#define CPR0_ICFG 0x140 -#define CPR0_ICFG_RLI_MASK 0x80000000 -#define CPR0_ICFG_RLI_RESETCPR 0x00000000 -#define CPR0_ICFG_RLI_PRESERVECPR 0x80000000 -#define CPR0_ICFG_ICS_MASK 0x00000007 -#endif /* defined (CONFIG_440EPX) || defined (CONFIG_440GRX) */ /*----------------------------------------------------------------------------- | IIC Register Offsets @@ -3006,20 +1931,6 @@ #define IICDIRECTCNTL 0x10 /*----------------------------------------------------------------------------- -| UART Register Offsets -'----------------------------------------------------------------------------*/ -#define DATA_REG 0x00 -#define DL_LSB 0x00 -#define DL_MSB 0x01 -#define INT_ENABLE 0x01 -#define FIFO_CONTROL 0x02 -#define LINE_CONTROL 0x03 -#define MODEM_CONTROL 0x04 -#define LINE_STATUS 0x05 -#define MODEM_STATUS 0x06 -#define SCRATCH 0x07 - -/*----------------------------------------------------------------------------- | PCI Internal Registers et. al. (accessed via plb) +----------------------------------------------------------------------------*/ #define PCIX0_CFGADR (CFG_PCI_BASE + 0x0ec00000) @@ -3145,7 +2056,8 @@ * GPIO macro register defines ******************************************************************************/ #if defined(CONFIG_440GP) || defined(CONFIG_440GX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460SX) #define GPIO0_BASE (CFG_PERIPHERAL_BASE+0x00000700) #define GPIO0_OR (GPIO0_BASE+0x0) diff --git a/include/ppc4xx.h b/include/ppc4xx.h index 0a8479f..d593b07 100644 --- a/include/ppc4xx.h +++ b/include/ppc4xx.h @@ -41,7 +41,8 @@ #if defined(CONFIG_405EX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) #define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */ #endif @@ -52,6 +53,8 @@ #endif #include <asm/ppc4xx-sdram.h> +#include <asm/ppc4xx-ebc.h> +#include <asm/ppc4xx-uic.h> /* * Macro for generating register field mnemonics diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h index 4c97b36..b74c6fc 100644 --- a/include/ppc4xx_enet.h +++ b/include/ppc4xx_enet.h @@ -153,6 +153,20 @@ typedef struct emac_4xx_hw_st { #define SDR0_PFC1_EM_1000 (0x00200000) #endif +/* + * XMII bridge configurations for those systems (e.g. 405EX(r)) that do + * not have a pin function control (PFC) register to otherwise determine + * the bridge configuration. + */ +#define EMAC_PHY_MODE_NONE 0 +#define EMAC_PHY_MODE_NONE_RGMII 1 +#define EMAC_PHY_MODE_RGMII_NONE 2 +#define EMAC_PHY_MODE_RGMII_RGMII 3 +#define EMAC_PHY_MODE_NONE_GMII 4 +#define EMAC_PHY_MODE_GMII_NONE 5 +#define EMAC_PHY_MODE_NONE_MII 6 +#define EMAC_PHY_MODE_MII_NONE 7 + /* ZMII Bridge Register addresses */ #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ @@ -218,12 +232,12 @@ typedef struct emac_4xx_hw_st { #endif /* RGMII Function Enable (FER) Register Bit Definitions */ -/* Note: for EMAC 2 and 3 only, 440GX only */ #define RGMII_FER_DIS (0x00) #define RGMII_FER_RTBI (0x04) #define RGMII_FER_RGMII (0x05) #define RGMII_FER_TBI (0x06) #define RGMII_FER_GMII (0x07) +#define RGMII_FER_MII (RGMII_FER_GMII) #define RGMII_FER_V(__x) ((__x - 2) * 4) |