diff options
36 files changed, 2323 insertions, 36 deletions
diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c index c7dad66..2b15a64 100644 --- a/arch/arm/cpu/armv7/am33xx/board.c +++ b/arch/arm/cpu/armv7/am33xx/board.c @@ -36,11 +36,15 @@ DECLARE_GLOBAL_DATA_PTR; -static const struct gpio_bank gpio_bank_am33xx[4] = { +static const struct gpio_bank gpio_bank_am33xx[] = { { (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX }, { (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX }, { (void *)AM33XX_GPIO2_BASE, METHOD_GPIO_24XX }, { (void *)AM33XX_GPIO3_BASE, METHOD_GPIO_24XX }, +#ifdef CONFIG_AM43XX + { (void *)AM33XX_GPIO4_BASE, METHOD_GPIO_24XX }, + { (void *)AM33XX_GPIO5_BASE, METHOD_GPIO_24XX }, +#endif }; const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx; diff --git a/arch/arm/cpu/armv7/am33xx/clock_am43xx.c b/arch/arm/cpu/armv7/am33xx/clock_am43xx.c index 97c00b4..440cf8b 100644 --- a/arch/arm/cpu/armv7/am33xx/clock_am43xx.c +++ b/arch/arm/cpu/armv7/am33xx/clock_am43xx.c @@ -94,6 +94,8 @@ void enable_basic_clocks(void) &cmper->gpio1clkctrl, &cmper->gpio2clkctrl, &cmper->gpio3clkctrl, + &cmper->gpio4clkctrl, + &cmper->gpio5clkctrl, &cmper->i2c1clkctrl, &cmper->emiffwclkctrl, &cmper->emifclkctrl, diff --git a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c index ef14f47..9b5a47b 100644 --- a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c +++ b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c @@ -211,11 +211,8 @@ static u32 pll_dco_freq_sel(u32 clkout_dco) static u32 pll_sigma_delta_val(u32 clkout_dco) { u32 sig_val = 0; - float frac_div; - frac_div = (float) clkout_dco / 250; - frac_div = frac_div + 0.90; - sig_val = (int)frac_div; + sig_val = (clkout_dco + 225) / 250; sig_val = sig_val << 24; return sig_val; diff --git a/arch/arm/cpu/armv7/omap4/hw_data.c b/arch/arm/cpu/armv7/omap4/hw_data.c index 4dec73e..029533c 100644 --- a/arch/arm/cpu/armv7/omap4/hw_data.c +++ b/arch/arm/cpu/armv7/omap4/hw_data.c @@ -172,6 +172,20 @@ struct dplls omap4430_dplls_es1 = { .ddr = NULL }; +struct dplls omap4430_dplls_es20 = { + .mpu = mpu_dpll_params_1200mhz, + .core = core_dpll_params_es2_1600mhz_ddr200mhz, + .per = per_dpll_params_1536mhz, + .iva = iva_dpll_params_1862mhz, +#ifdef CONFIG_SYS_OMAP_ABE_SYSCK + .abe = abe_dpll_params_sysclk_196608khz, +#else + .abe = &abe_dpll_params_32k_196608khz, +#endif + .usb = usb_dpll_params_1920mhz, + .ddr = NULL +}; + struct dplls omap4430_dplls = { .mpu = mpu_dpll_params_1200mhz, .core = core_dpll_params_1600mhz, @@ -413,6 +427,10 @@ void hw_data_init(void) break; case OMAP4430_ES2_0: + *dplls_data = &omap4430_dplls_es20; + *omap_vcores = &omap4430_volts; + break; + case OMAP4430_ES2_1: case OMAP4430_ES2_2: case OMAP4430_ES2_3: diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c index ff32807..7292161 100644 --- a/arch/arm/cpu/armv7/omap5/prcm-regs.c +++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c @@ -432,7 +432,7 @@ struct omap_sys_ctrl_regs const dra7xx_ctrl = { .control_srcomp_code_latch = 0x4A002E84, .control_ddr_control_ext_0 = 0x4A002E88, .control_padconf_core_base = 0x4A003400, - .control_std_fuse_opp_vdd_mpu_2 = 0x4A003B24, + .control_std_fuse_opp_vdd_mpu_2 = 0x4A003B20, .control_port_emif1_sdram_config = 0x4AE0C110, .control_port_emif1_lpddr2_nvm_config = 0x4AE0C114, .control_port_emif2_sdram_config = 0x4AE0C118, diff --git a/arch/arm/include/asm/arch-am33xx/cpu.h b/arch/arm/include/asm/arch-am33xx/cpu.h index 9febfa2..97e8702 100644 --- a/arch/arm/include/asm/arch-am33xx/cpu.h +++ b/arch/arm/include/asm/arch-am33xx/cpu.h @@ -171,7 +171,8 @@ struct cm_wkuppll { unsigned int resv11[1]; unsigned int wkup_uart0ctrl; /* offset 0xB4 */ unsigned int wkup_i2c0ctrl; /* offset 0xB8 */ - unsigned int resv12[7]; + unsigned int wkup_adctscctrl; /* offset 0xBC */ + unsigned int resv12[6]; unsigned int divm6dpllcore; /* offset 0xD8 */ }; @@ -221,7 +222,8 @@ struct cm_perpll { unsigned int tpccclkctrl; /* offset 0xBC */ unsigned int dcan0clkctrl; /* offset 0xC0 */ unsigned int dcan1clkctrl; /* offset 0xC4 */ - unsigned int resv6[2]; + unsigned int resv6; + unsigned int epwmss1clkctrl; /* offset 0xCC */ unsigned int emiffwclkctrl; /* offset 0xD0 */ unsigned int epwmss0clkctrl; /* offset 0xD4 */ unsigned int epwmss2clkctrl; /* offset 0xD8 */ @@ -351,7 +353,11 @@ struct cm_perpll { unsigned int gpio2clkctrl; /* offset 0x480 */ unsigned int resv20; unsigned int gpio3clkctrl; /* offset 0x488 */ - unsigned int resv21[7]; + unsigned int resv41; + unsigned int gpio4clkctrl; /* offset 0x490 */ + unsigned int resv42; + unsigned int gpio5clkctrl; /* offset 0x498 */ + unsigned int resv21[3]; unsigned int i2c1clkctrl; /* offset 0x4A8 */ unsigned int resv22; diff --git a/arch/arm/include/asm/arch-am33xx/ddr_defs.h b/arch/arm/include/asm/arch-am33xx/ddr_defs.h index fbe599d..4d89952 100644 --- a/arch/arm/include/asm/arch-am33xx/ddr_defs.h +++ b/arch/arm/include/asm/arch-am33xx/ddr_defs.h @@ -58,6 +58,22 @@ #define MT41J128MJT125_PHY_FIFO_WE 0x100 #define MT41J128MJT125_IOCTRL_VALUE 0x18B +/* Micron MT41K128M16JT-187E */ +#define MT41K128MJT187E_EMIF_READ_LATENCY 0x06 +#define MT41K128MJT187E_EMIF_TIM1 0x0888B3DB +#define MT41K128MJT187E_EMIF_TIM2 0x36337FDA +#define MT41K128MJT187E_EMIF_TIM3 0x501F830F +#define MT41K128MJT187E_EMIF_SDCFG 0x61C04AB2 +#define MT41K128MJT187E_EMIF_SDREF 0x0000093B +#define MT41K128MJT187E_ZQ_CFG 0x50074BE4 +#define MT41K128MJT187E_RATIO 0x40 +#define MT41K128MJT187E_INVERT_CLKOUT 0x1 +#define MT41K128MJT187E_RD_DQS 0x3B +#define MT41K128MJT187E_WR_DQS 0x85 +#define MT41K128MJT187E_PHY_WR_DATA 0xC1 +#define MT41K128MJT187E_PHY_FIFO_WE 0x100 +#define MT41K128MJT187E_IOCTRL_VALUE 0x18B + /* Micron MT41J64M16JT-125 */ #define MT41J64MJT125_EMIF_SDCFG 0x61C04A32 diff --git a/arch/arm/include/asm/arch-am33xx/gpio.h b/arch/arm/include/asm/arch-am33xx/gpio.h index a1ffd49..220603d 100644 --- a/arch/arm/include/asm/arch-am33xx/gpio.h +++ b/arch/arm/include/asm/arch-am33xx/gpio.h @@ -12,8 +12,8 @@ #define AM33XX_GPIO1_BASE 0x4804C000 #define AM33XX_GPIO2_BASE 0x481AC000 #define AM33XX_GPIO3_BASE 0x481AE000 - -#define GPIO_22 22 +#define AM33XX_GPIO4_BASE 0x48320000 +#define AM33XX_GPIO5_BASE 0x48322000 /* GPIO CTRL register */ #define GPIO_CTRL_DISABLEMODULE_SHIFT 0 diff --git a/board/BuR/common/bur_common.h b/board/BuR/common/bur_common.h new file mode 100644 index 0000000..15225b0 --- /dev/null +++ b/board/BuR/common/bur_common.h @@ -0,0 +1,22 @@ +/* + * bur_comon.h + * + * common board information header for B&R boards + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _BUR_COMMON_H_ +#define _BUR_COMMON_H_ + +void blink(u32 blinks, u32 intervall, u32 pin); +void pmicsetup(u32 mpupll); +void enable_uart0_pin_mux(void); +void enable_i2c0_pin_mux(void); +void enable_board_pin_mux(void); +int board_eth_init(bd_t *bis); + +#endif diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c new file mode 100644 index 0000000..6d187ea --- /dev/null +++ b/board/BuR/common/common.c @@ -0,0 +1,216 @@ +/* + * common.c + * + * common board functions for B&R boards + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + * + */ + +#include <common.h> +#include <errno.h> +#include <spl.h> +#include <asm/arch/cpu.h> +#include <asm/arch/hardware.h> +#include <asm/arch/omap.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <asm/arch/sys_proto.h> +#include <asm/io.h> +#include <asm/gpio.h> +#include <i2c.h> +#include <miiphy.h> +#include <cpsw.h> +#include <power/tps65217.h> +#include "bur_common.h" + +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; +/* --------------------------------------------------------------------------*/ +void blink(u32 blinks, u32 intervall, u32 pin) +{ + gpio_direction_output(pin, 0); + int val = 0; + + do { + val ^= 0x01; + gpio_set_value(pin, val); + mdelay(intervall); + } while (blinks--); + + gpio_set_value(pin, 0); +} +#ifdef CONFIG_SPL_BUILD +void pmicsetup(u32 mpupll) +{ + int mpu_vdd; + int usb_cur_lim; + + /* setup I2C */ + enable_i2c0_pin_mux(); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); + + if (i2c_probe(TPS65217_CHIP_PM)) { + puts("PMIC (0x24) not found! skip further initalization.\n"); + return; + } + + /* Get the frequency which is defined by device fuses */ + dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); + printf("detected max. frequency: %d - ", dpll_mpu_opp100.m); + + if (0 != mpupll) { + dpll_mpu_opp100.m = MPUPLL_M_1000; + printf("retuning MPU-PLL to: %d MHz.\n", dpll_mpu_opp100.m); + } else { + puts("ok.\n"); + } + /* + * Increase USB current limit to 1300mA or 1800mA and set + * the MPU voltage controller as needed. + */ + if (dpll_mpu_opp100.m == MPUPLL_M_1000) { + usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA; + mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV; + } else { + usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA; + mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV; + } + + if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH, + usb_cur_lim, TPS65217_USB_INPUT_CUR_LIMIT_MASK)) + puts("tps65217_reg_write failure\n"); + + /* Set DCDC3 (CORE) voltage to 1.125V */ + if (tps65217_voltage_update(TPS65217_DEFDCDC3, + TPS65217_DCDC_VOLT_SEL_1125MV)) { + puts("tps65217_voltage_update failure\n"); + return; + } + + /* Set CORE Frequencies to OPP100 */ + do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); + + /* Set DCDC2 (MPU) voltage */ + if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) { + puts("tps65217_voltage_update failure\n"); + return; + } + + /* Set LDO3 to 1.8V */ + if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, + TPS65217_DEFLS1, + TPS65217_LDO_VOLTAGE_OUT_1_8, + TPS65217_LDO_MASK)) + puts("tps65217_reg_write failure\n"); + /* Set LDO4 to 3.3V */ + if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, + TPS65217_DEFLS2, + TPS65217_LDO_VOLTAGE_OUT_3_3, + TPS65217_LDO_MASK)) + puts("tps65217_reg_write failure\n"); + + /* Set MPU Frequency to what we detected now that voltages are set */ + do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100); +} + +void set_uart_mux_conf(void) +{ + enable_uart0_pin_mux(); +} + +void set_mux_conf_regs(void) +{ + enable_board_pin_mux(); +} + +#endif /* CONFIG_SPL_BUILD */ + +#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ + (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) +static void cpsw_control(int enabled) +{ + /* VTP can be added here */ + return; +} + +/* describing port offsets of TI's CPSW block */ +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x208, + .sliver_reg_ofs = 0xd80, + .phy_id = 0, + }, + { + .slave_reg_ofs = 0x308, + .sliver_reg_ofs = 0xdc0, + .phy_id = 1, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = CPSW_MDIO_BASE, + .cpsw_base = CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x800, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0xd00, + .ale_entries = 1024, + .host_port_reg_ofs = 0x108, + .hw_stats_reg_ofs = 0x900, + .bd_ram_ofs = 0x2000, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_2, +}; +#endif /* CONFIG_DRIVER_TI_CPSW, ... */ + +#if defined(CONFIG_DRIVER_TI_CPSW) + +int board_eth_init(bd_t *bis) +{ + int rv = 0; + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + + /* try reading mac address from efuse */ + mac_lo = readl(&cdev->macid0l); + mac_hi = readl(&cdev->macid0h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + +#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ + (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) + if (!getenv("ethaddr")) { + printf("<ethaddr> not set. Validating first E-fuse MAC ... "); + + if (is_valid_ether_addr(mac_addr)) { + printf("using: %02X:%02X:%02X:%02X:%02X:%02X.\n", + mac_addr[0], mac_addr[1], mac_addr[2], + mac_addr[3], mac_addr[4], mac_addr[5] + ); + eth_setenv_enetaddr("ethaddr", mac_addr); + } + } + writel(MII_MODE_ENABLE, &cdev->miisel); + cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII; + cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII; + + rv = cpsw_register(&cpsw_data); + if (rv < 0) { + printf("Error %d registering CPSW switch\n", rv); + return 0; + } +#endif /* CONFIG_DRIVER_TI_CPSW, ... */ + return rv; +} +#endif /* CONFIG_DRIVER_TI_CPSW */ diff --git a/board/BuR/kwb/Makefile b/board/BuR/kwb/Makefile new file mode 100644 index 0000000..7b04b26 --- /dev/null +++ b/board/BuR/kwb/Makefile @@ -0,0 +1,12 @@ +# +# Makefile +# +# Copyright (C) 2014 Hannes Petermaier <oe5hpm@oevsv.at> - +# Bernecker & Rainer Industrielektronik GmbH - http://www.br-automation.com/ +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-$(CONFIG_SPL_BUILD) += mux.o +obj-y += ../common/common.o +obj-y += board.o diff --git a/board/BuR/kwb/board.c b/board/BuR/kwb/board.c new file mode 100644 index 0000000..8aa16bc --- /dev/null +++ b/board/BuR/kwb/board.c @@ -0,0 +1,240 @@ +/* + * board.c + * + * Board functions for B&R KWB Board + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + * + */ +#include <common.h> +#include <errno.h> +#include <spl.h> +#include <asm/arch/cpu.h> +#include <asm/arch/hardware.h> +#include <asm/arch/omap.h> +#include <asm/arch/ddr_defs.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/mem.h> +#include <asm/io.h> +#include <asm/emif.h> +#include <asm/gpio.h> +#include <i2c.h> +#include <power/tps65217.h> +#include "../common/bur_common.h" + +/* -------------------------------------------------------------------------*/ +/* -- defines for used GPIO Hardware -- */ +#define KEY (0+4) +#define LCD_PWR (0+5) +#define PUSH_KEY (0+31) +#define USB2SD_NRST (32+29) +#define USB2SD_PWR (96+13) +/* -------------------------------------------------------------------------*/ +/* -- PSOC Resetcontroller Register defines -- */ + +/* I2C Address of controller */ +#define RSTCTRL_ADDR 0x75 +/* Register for CTRL-word */ +#define RSTCTRL_CTRLREG 0x01 +/* Register for giving some information to VxWorks OS */ +#define RSTCTRL_SCRATCHREG 0x04 + +/* -- defines for RSTCTRL_CTRLREG -- */ +#define RSTCTRL_FORCE_PWR_NEN 0x0404 + +#if defined(CONFIG_SPL_BUILD) +/* TODO: check ram-timing ! */ +static const struct ddr_data ddr3_data = { + .datardsratio0 = MT41K256M16HA125E_RD_DQS, + .datawdsratio0 = MT41K256M16HA125E_WR_DQS, + .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE, + .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA, +}; +static const struct cmd_control ddr3_cmd_ctrl_data = { + .cmd0csratio = MT41K256M16HA125E_RATIO, + .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT, + + .cmd1csratio = MT41K256M16HA125E_RATIO, + .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT, + + .cmd2csratio = MT41K256M16HA125E_RATIO, + .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT, +}; +static struct emif_regs ddr3_emif_reg_data = { + .sdram_config = MT41K256M16HA125E_EMIF_SDCFG, + .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF, + .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1, + .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2, + .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3, + .zq_config = MT41K256M16HA125E_ZQ_CFG, + .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY, +}; + +static const struct ctrl_ioregs ddr3_ioregs = { + .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, +}; + +#define OSC (V_OSCK/1000000) +const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1}; + +void am33xx_spl_board_init(void) +{ + unsigned int oldspeed; + unsigned short buf; + + struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER; + struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP; + /* + * enable additional clocks of modules which are accessed later from + * VxWorks OS + */ + u32 *const clk_domains[] = { 0 }; + + u32 *const clk_modules_kwbspecific[] = { + &cmwkup->wkup_adctscctrl, + &cmper->spi1clkctrl, + &cmper->dcan0clkctrl, + &cmper->dcan1clkctrl, + &cmper->epwmss0clkctrl, + &cmper->epwmss1clkctrl, + &cmper->epwmss2clkctrl, + 0 + }; + do_enable_clocks(clk_domains, clk_modules_kwbspecific, 1); + + /* power-OFF LCD-Display */ + gpio_direction_output(LCD_PWR, 0); + + /* setup I2C */ + enable_i2c0_pin_mux(); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); + + /* power-ON 3V3 via Resetcontroller */ + oldspeed = i2c_get_bus_speed(); + if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) { + buf = RSTCTRL_FORCE_PWR_NEN; + i2c_write(RSTCTRL_ADDR, RSTCTRL_CTRLREG, 1, + (uint8_t *)&buf, sizeof(buf)); + i2c_set_bus_speed(oldspeed); + } else { + puts("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n"); + } + +#if defined(CONFIG_AM335X_USB0) + /* power on USB2SD Controller */ + gpio_direction_output(USB2SD_PWR, 1); + mdelay(1); + /* give a reset Pulse to USB2SD Controller */ + gpio_direction_output(USB2SD_NRST, 0); + mdelay(1); + gpio_set_value(USB2SD_NRST, 1); +#endif + pmicsetup(0); +} + +const struct dpll_params *get_dpll_ddr_params(void) +{ + return &dpll_ddr3; +} + +void sdram_init(void) +{ + config_ddr(400, &ddr3_ioregs, + &ddr3_data, + &ddr3_cmd_ctrl_data, + &ddr3_emif_reg_data, 0); +} +#endif /* CONFIG_SPL_BUILD */ +/* + * Basic board specific setup. Pinmux has been handled already. + */ +int board_init(void) +{ + gpmc_init(); + return 0; +} + +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + const unsigned int ton = 250; + const unsigned int toff = 1000; + unsigned int cnt = 3; + unsigned short buf = 0xAAAA; + unsigned int oldspeed; + + tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, + TPS65217_WLEDCTRL2, 0x32, 0xFF); /* 50% dimlevel */ + + if (gpio_get_value(KEY)) { + do { + /* turn on light */ + tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, + TPS65217_WLEDCTRL1, 0x09, 0xFF); + mdelay(ton); + /* turn off light */ + tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, + TPS65217_WLEDCTRL1, 0x01, 0xFF); + mdelay(toff); + cnt--; + if (!gpio_get_value(KEY) && + gpio_get_value(PUSH_KEY) && 1 == cnt) { + puts("updating from USB ...\n"); + setenv("bootcmd", "run usbupdate"); + break; + } else if (!gpio_get_value(KEY)) { + break; + } + } while (cnt); + } + + switch (cnt) { + case 0: + puts("3 blinks ... entering BOOT mode.\n"); + buf = 0x0000; + break; + case 1: + puts("2 blinks ... entering DIAGNOSE mode.\n"); + buf = 0x0F0F; + break; + case 2: + puts("1 blinks ... entering SERVICE mode.\n"); + buf = 0xB4B4; + break; + case 3: + puts("0 blinks ... entering RUN mode.\n"); + buf = 0x0404; + break; + } + mdelay(ton); + /* turn on light */ + tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, + TPS65217_WLEDCTRL1, 0x09, 0xFF); + /* write bootinfo into scratchregister of resetcontroller */ + oldspeed = i2c_get_bus_speed(); + if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) { + i2c_write(RSTCTRL_ADDR, RSTCTRL_SCRATCHREG, 1, + (uint8_t *)&buf, sizeof(buf)); + i2c_set_bus_speed(oldspeed); + } else { + puts("ERROR: i2c_set_bus_speed failed! (scratchregister)\n"); + } + /* + * reset VBAR registers to its reset location, VxWorks 6.9.3.2 does + * expect that vectors are there, original u-boot moves them to _start + */ + __asm__("ldr r0,=0x20000"); + __asm__("mcr p15, 0, r0, c12, c0, 0"); /* Set VBAR */ + + return 0; +} +#endif /* CONFIG_BOARD_LATE_INIT */ diff --git a/board/BuR/kwb/mux.c b/board/BuR/kwb/mux.c new file mode 100644 index 0000000..1a5ffd5 --- /dev/null +++ b/board/BuR/kwb/mux.c @@ -0,0 +1,195 @@ +/* + * mux.c + * + * Pinmux Setting for B&R LEIT Board(s) + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/hardware.h> +#include <asm/arch/mux.h> +#include <asm/io.h> +#include <i2c.h> + +static struct module_pin_mux usb0_pin_mux[] = { + {OFFSET(usb0_id), (MODE(0) | RXACTIVE)}, + /* USB0 DrvBus Receiver disable (from romcode 0x20) */ + {OFFSET(usb0_drvvbus), (MODE(0))}, + /* USB1 DrvBus as GPIO due to HW-Workaround */ + {OFFSET(usb1_drvvbus), (MODE(7))}, + {-1}, +}; +static struct module_pin_mux spi1_pin_mux[] = { + /* SPI1_SCLK */ + {OFFSET(mcasp0_aclkx), MODE(3) | PULLUDEN | RXACTIVE}, + /* SPI1_D0 */ + {OFFSET(mcasp0_fsx), MODE(3) | PULLUDEN | RXACTIVE}, + /* SPI1_D1 */ + {OFFSET(mcasp0_axr0), MODE(3) | PULLUDEN | RXACTIVE}, + /* SPI1_CS0 */ + {OFFSET(mcasp0_ahclkr), MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE}, + {-1}, +}; + +static struct module_pin_mux dcan0_pin_mux[] = { + /* DCAN0 TX */ + {OFFSET(uart1_ctsn), MODE(2) | PULLUDEN | PULLUP_EN}, + /* DCAN0 RX */ + {OFFSET(uart1_rtsn), MODE(2) | RXACTIVE}, + {-1}, +}; + +static struct module_pin_mux dcan1_pin_mux[] = { + /* DCAN1 TX */ + {OFFSET(uart1_rxd), MODE(2) | PULLUDEN | PULLUP_EN}, + /* DCAN1 RX */ + {OFFSET(uart1_txd), MODE(2) | RXACTIVE}, + {-1}, +}; + +static struct module_pin_mux gpios[] = { + /* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */ + {OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS)}, + /* GPIO0_4 (SPI D1) - TA602 */ + {OFFSET(spi0_d1), (MODE(7) | PULLUDDIS | RXACTIVE)}, + /* GPIO0_5 (SPI CS0) - DISPLAY_ON_OFF */ + {OFFSET(spi0_cs0), (MODE(7) | PULLUDDIS)}, + /* GPIO0_7 (PWW0 OUT) - CAN TERM */ + {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDDIS | RXACTIVE)}, + /* GPIO0_19 (DMA_INTR0) - CLKOUT SYS */ + {OFFSET(xdma_event_intr0), (MODE(7) | RXACTIVE)}, + /* GPIO0_20 (DMA_INTR1) - SPI1 nCS1 */ + {OFFSET(xdma_event_intr1), (MODE(7) | PULLUDEN | PULLUP_EN)}, + /* GPIO0_30 (GPMC_WAIT0) - TA601 */ + {OFFSET(gpmc_wait0), (MODE(7) | PULLUDDIS | RXACTIVE)}, + /* GPIO0_31 (GPMC_nWP) - SW601 PushButton */ + {OFFSET(gpmc_wpn), (MODE(7) | PULLUDDIS | RXACTIVE)}, + /* GPIO1_28 (GPMC_nWE) - FRAM_nWP */ + {OFFSET(gpmc_be1n), (MODE(7) | PULLUDDIS)}, + /* GPIO2_0 (GPMC_nCS3) - VBAT_OK */ + {OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) }, + /* GPIO2_2 (GPMC_nADV_ALE) - DCOK */ + {OFFSET(gpmc_advn_ale), (MODE(7) | PULLUDDIS | RXACTIVE)}, + /* GPIO2_4 (GPMC_nWE) - TST_BAST */ + {OFFSET(gpmc_wen), (MODE(7) | PULLUDDIS)}, + /* GPIO3_18 (MCASP0_ACLKR) - SW601 CNTup, mapped to Counter eQEB0A_in */ + {OFFSET(mcasp0_aclkr), (MODE(1) | PULLUDDIS | RXACTIVE)}, + /* GPIO3_19 (MCASP0_FSR) - SW601 CNTdown, mapped to Counter eQEB0B_in */ + {OFFSET(mcasp0_fsr), (MODE(1) | PULLUDDIS | RXACTIVE)}, + /* GPIO3_20 (MCASP0_AXR1) - SW601 CNTdown, map to Counter eQEB0_index */ + {OFFSET(mcasp0_axr1), (MODE(1) | PULLUDDIS | RXACTIVE)}, + {-1}, +}; + +static struct module_pin_mux uart0_pin_mux[] = { + /* UART0_CTS */ + {OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* UART0_RXD */ + {OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* UART0_TXD */ + {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, + {-1}, +}; + +static struct module_pin_mux i2c0_pin_mux[] = { + /* I2C_DATA */ + {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)}, + /* I2C_SCLK */ + {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)}, + {-1}, +}; + +static struct module_pin_mux mii1_pin_mux[] = { + {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */ + {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */ + {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */ + {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */ + {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */ + {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */ + {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */ + {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */ + {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */ + {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */ + {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */ + {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */ + {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */ + {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */ + {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ + {-1}, +}; + +static struct module_pin_mux mmc1_pin_mux[] = { + {OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT3 */ + {OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT2 */ + {OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT1 */ + {OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT0 */ + {OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CLK */ + {OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CMD */ + {OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)}, /* MMC1_WP */ + {OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */ + + {-1}, +}; + +static struct module_pin_mux lcd_pin_mux[] = { + {OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)}, /* LCD-Data(0) */ + {OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)}, /* LCD-Data(1) */ + {OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)}, /* LCD-Data(2) */ + {OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)}, /* LCD-Data(3) */ + {OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)}, /* LCD-Data(4) */ + {OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)}, /* LCD-Data(5) */ + {OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)}, /* LCD-Data(6) */ + {OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)}, /* LCD-Data(7) */ + {OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)}, /* LCD-Data(8) */ + {OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)}, /* LCD-Data(9) */ + {OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)}, /* LCD-Data(10) */ + {OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)}, /* LCD-Data(11) */ + {OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)}, /* LCD-Data(12) */ + {OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)}, /* LCD-Data(13) */ + {OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)}, /* LCD-Data(14) */ + {OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)}, /* LCD-Data(15) */ + + {OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)}, /* LCD-Data(16) */ + {OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)}, /* LCD-Data(17) */ + {OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)}, /* LCD-Data(18) */ + {OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)}, /* LCD-Data(19) */ + {OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)}, /* LCD-Data(20) */ + {OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)}, /* LCD-Data(21) */ + {OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)}, /* LCD-Data(22) */ + {OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)}, /* LCD-Data(23) */ + + {OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)}, /* LCD-VSync */ + {OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)}, /* LCD-HSync */ + {OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */ + {OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)}, /* LCD-CLK */ + + {-1}, +}; + +void enable_uart0_pin_mux(void) +{ + configure_module_pin_mux(uart0_pin_mux); +} + +void enable_i2c0_pin_mux(void) +{ + configure_module_pin_mux(i2c0_pin_mux); +} + +void enable_board_pin_mux(void) +{ + configure_module_pin_mux(i2c0_pin_mux); + configure_module_pin_mux(mii1_pin_mux); + configure_module_pin_mux(usb0_pin_mux); + configure_module_pin_mux(spi1_pin_mux); + configure_module_pin_mux(dcan0_pin_mux); + configure_module_pin_mux(dcan1_pin_mux); + configure_module_pin_mux(mmc1_pin_mux); + configure_module_pin_mux(lcd_pin_mux); + configure_module_pin_mux(gpios); +} diff --git a/board/BuR/tseries/Makefile b/board/BuR/tseries/Makefile new file mode 100644 index 0000000..ec0d27a --- /dev/null +++ b/board/BuR/tseries/Makefile @@ -0,0 +1,14 @@ +# +# Makefile +# +# Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> +# Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifeq ($(CONFIG_SPL_BUILD),y) +obj-y := mux.o +endif +obj-y += ../common/common.o +obj-y += board.o diff --git a/board/BuR/tseries/board.c b/board/BuR/tseries/board.c new file mode 100644 index 0000000..f0510e5 --- /dev/null +++ b/board/BuR/tseries/board.c @@ -0,0 +1,147 @@ +/* + * board.c + * + * Board functions for B&R LEIT Board + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + * + */ + +#include <common.h> +#include <errno.h> +#include <spl.h> +#include <asm/arch/cpu.h> +#include <asm/arch/hardware.h> +#include <asm/arch/omap.h> +#include <asm/arch/ddr_defs.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/mem.h> +#include <asm/io.h> +#include <asm/emif.h> +#include <asm/gpio.h> +#include <i2c.h> +#include <power/tps65217.h> +#include "../common/bur_common.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* --------------------------------------------------------------------------*/ +/* -- defines for GPIO -- */ +#define ETHLED_ORANGE (96+16) /* GPIO3_16 */ +#define REPSWITCH (0+20) /* GPIO0_20 */ + + +#if defined(CONFIG_SPL_BUILD) +/* TODO: check ram-timing ! */ +static const struct ddr_data ddr3_data = { + .datardsratio0 = MT41K256M16HA125E_RD_DQS, + .datawdsratio0 = MT41K256M16HA125E_WR_DQS, + .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE, + .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA, +}; + +static const struct cmd_control ddr3_cmd_ctrl_data = { + .cmd0csratio = MT41K256M16HA125E_RATIO, + .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT, + + .cmd1csratio = MT41K256M16HA125E_RATIO, + .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT, + + .cmd2csratio = MT41K256M16HA125E_RATIO, + .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT, +}; + +static struct emif_regs ddr3_emif_reg_data = { + .sdram_config = MT41K256M16HA125E_EMIF_SDCFG, + .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF, + .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1, + .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2, + .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3, + .zq_config = MT41K256M16HA125E_ZQ_CFG, + .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY, +}; + +static const struct ctrl_ioregs ddr3_ioregs = { + .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE, + .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE, +}; + +#ifdef CONFIG_SPL_OS_BOOT +/* + * called from spl_nand.c + * return 0 for loading linux, return 1 for loading u-boot + */ +int spl_start_uboot(void) +{ + if (0 == gpio_get_value(REPSWITCH)) { + blink(5, 125, ETHLED_ORANGE); + mdelay(1000); + printf("SPL: entering u-boot instead kernel image.\n"); + return 1; + } + return 0; +} +#endif /* CONFIG_SPL_OS_BOOT */ + +#define OSC (V_OSCK/1000000) +static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1}; + +void am33xx_spl_board_init(void) +{ + pmicsetup(1000); +} + +const struct dpll_params *get_dpll_ddr_params(void) +{ + return &dpll_ddr3; +} + +void sdram_init(void) +{ + config_ddr(400, &ddr3_ioregs, + &ddr3_data, + &ddr3_cmd_ctrl_data, + &ddr3_emif_reg_data, 0); +} +#endif /* CONFIG_SPL_BUILD */ + +/* Basic board specific setup. Pinmux has been handled already. */ +int board_init(void) +{ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + gpmc_init(); + return 0; +} + +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + gpio_direction_output(ETHLED_ORANGE, 0); + + if (0 == gpio_get_value(REPSWITCH)) { + printf("\n\n\n" + "!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n" + "!!!!!!! recovery switch activated !!!!!!!\n" + "!!!!!!! running usbupdate !!!!!!!\n" + "!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n\n\n"); + setenv("bootcmd", "sleep 2; run netupdate;"); + } + + printf("turning on display power+backlight ... "); + tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL1, + 0x09, TPS65217_MASK_ALL_BITS); /* 200 Hz, ON */ + tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL2, + 0x62, TPS65217_MASK_ALL_BITS); /* 100% */ + printf("ok.\n"); + + return 0; +} +#endif /* CONFIG_BOARD_LATE_INIT */ diff --git a/board/BuR/tseries/mux.c b/board/BuR/tseries/mux.c new file mode 100644 index 0000000..3c76e96 --- /dev/null +++ b/board/BuR/tseries/mux.c @@ -0,0 +1,225 @@ +/* + * mux.c + * + * Pinmux Setting for B&R LEIT Board(s) + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/hardware.h> +#include <asm/arch/mux.h> +#include <asm/io.h> +#include <i2c.h> + +static struct module_pin_mux uart0_pin_mux[] = { + /* UART0_CTS */ + {OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* UART0_RXD */ + {OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* UART0_TXD */ + {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, + {-1}, +}; +#ifdef CONFIG_MMC +static struct module_pin_mux mmc1_pin_mux[] = { + {OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT3 */ + {OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT2 */ + {OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT1 */ + {OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT0 */ + {OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CLK */ + {OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* MMC1_CMD */ + {OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)}, /* MMC1_WP */ + {OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */ + {-1}, +}; +#endif +static struct module_pin_mux i2c0_pin_mux[] = { + /* I2C_DATA */ + {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)}, + /* I2C_SCLK */ + {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)}, + {-1}, +}; + +static struct module_pin_mux spi0_pin_mux[] = { + /* SPI0_SCLK */ + {OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)}, + /* SPI0_D0 */ + {OFFSET(spi0_d0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)}, + /* SPI0_D1 */ + {OFFSET(spi0_d1), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)}, + /* SPI0_CS0 */ + {OFFSET(spi0_cs0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)}, + {-1}, +}; + +static struct module_pin_mux mii1_pin_mux[] = { + {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */ + {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */ + {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */ + {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */ + {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */ + {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */ + {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */ + {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */ + {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */ + {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */ + {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */ + {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */ + {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */ + {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */ + {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ + {-1}, +}; + +static struct module_pin_mux mii2_pin_mux[] = { + {OFFSET(gpmc_a0), MODE(1)}, /* MII2_TXEN */ + {OFFSET(gpmc_a1), MODE(1) | RXACTIVE}, /* MII2_RXDV */ + {OFFSET(gpmc_a2), MODE(1)}, /* MII2_TXD3 */ + {OFFSET(gpmc_a3), MODE(1)}, /* MII2_TXD2 */ + {OFFSET(gpmc_a4), MODE(1)}, /* MII2_TXD1 */ + {OFFSET(gpmc_a5), MODE(1)}, /* MII2_TXD0 */ + {OFFSET(gpmc_a6), MODE(1) | RXACTIVE}, /* MII2_TXCLK */ + {OFFSET(gpmc_a7), MODE(1) | RXACTIVE}, /* MII2_RXCLK */ + {OFFSET(gpmc_a8), MODE(1) | RXACTIVE}, /* MII2_RXD3 */ + {OFFSET(gpmc_a9), MODE(1) | RXACTIVE}, /* MII2_RXD2 */ + {OFFSET(gpmc_a10), MODE(1) | RXACTIVE}, /* MII2_RXD1 */ + {OFFSET(gpmc_a11), MODE(1) | RXACTIVE}, /* MII2_RXD0 */ + {OFFSET(gpmc_wpn), (MODE(1) | RXACTIVE)},/* MII2_RXERR */ + /* + * MII2_CRS is shared with + * NAND_WAIT0 + */ + {OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */ + {-1}, +}; +#ifdef CONFIG_NAND +static struct module_pin_mux nand_pin_mux[] = { + {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */ + {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */ + {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */ + {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */ + {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */ + {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */ + {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */ + {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */ + {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */ + {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */ + {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */ + {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */ + {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */ + {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */ + {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */ + {-1}, +}; +#endif +static struct module_pin_mux gpIOs[] = { + /* GPIO0_6 (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */ + {OFFSET(spi0_cs1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* TIMER5 (MMC0_DAT3) - TIMER5 (Buzzer) */ + {OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)}, + /* TIMER6 (MMC0_DAT2) - PWM_BACK_3V3, later used as MODE3 for PWM */ + {OFFSET(mmc0_dat2), (MODE(7) | PULLUDEN | RXACTIVE)}, + /* GPIO2_28 (MMC0_DAT1) - MII_nNAND */ + {OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)}, + /* GPIO2_29 (MMC0_DAT0) - NAND_1n0 */ + {OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)}, + /* GPIO2_30 (MMC0_CLK) - nRESET (PHY) */ + {OFFSET(mmc0_clk), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* GPIO3_18 (MCASP0_ACLKR) - CPLD JTAG TDI */ + {OFFSET(mcasp0_aclkr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* GPIO3_19 (MCASP0_FSR) - CPLD JTAG TMS */ + {OFFSET(mcasp0_fsr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* GPIO3_20 (MCASP0_AXR1) - CPLD JTAG TCK */ + {OFFSET(mcasp0_axr1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* GPIO3_21 (MCASP0_AHCLKX) - CPLD JTAG TDO */ + {OFFSET(mcasp0_ahclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* GPIO2_0 (GPMC_nCS3) - DCOK */ + {OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) }, + /* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */ + {OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS | RXACTIVE) }, + /* + * GPIO0_7 (PWW0 OUT) + * DISPLAY_ONOFF (Backlight Enable at LVDS Versions) + */ + {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN | RXACTIVE)}, + /* GPIO0_19 (DMA_INTR0) - ISPLAY_MODE (CPLD) */ + {OFFSET(xdma_event_intr0), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, + /* GPIO0_20 (DMA_INTR1) - REP-Switch */ + {OFFSET(xdma_event_intr1), (MODE(7) | PULLUP_EN | RXACTIVE)}, + /* GPIO3_14 (MCASP0_ACLKX) - frei / PP709 */ + {OFFSET(mcasp0_aclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) }, + /* GPIO3_15 (MCASP0_FSX) - PMIC_nRESET */ + {OFFSET(mcasp0_fsx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) }, + /* GPIO3_16 (MCASP0_AXR0) - ETH1_LEDY */ + {OFFSET(mcasp0_axr0), (MODE(7) | PULLUDDIS) }, + /* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */ + {OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) }, + + {-1}, +}; + +static struct module_pin_mux lcd_pin_mux[] = { + {OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)}, /* LCD-Data(0) */ + {OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)}, /* LCD-Data(1) */ + {OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)}, /* LCD-Data(2) */ + {OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)}, /* LCD-Data(3) */ + {OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)}, /* LCD-Data(4) */ + {OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)}, /* LCD-Data(5) */ + {OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)}, /* LCD-Data(6) */ + {OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)}, /* LCD-Data(7) */ + {OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)}, /* LCD-Data(8) */ + {OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)}, /* LCD-Data(9) */ + {OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)}, /* LCD-Data(10) */ + {OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)}, /* LCD-Data(11) */ + {OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)}, /* LCD-Data(12) */ + {OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)}, /* LCD-Data(13) */ + {OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)}, /* LCD-Data(14) */ + {OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)}, /* LCD-Data(15) */ + + {OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)}, /* LCD-Data(16) */ + {OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)}, /* LCD-Data(17) */ + {OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)}, /* LCD-Data(18) */ + {OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)}, /* LCD-Data(19) */ + {OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)}, /* LCD-Data(20) */ + {OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)}, /* LCD-Data(21) */ + {OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)}, /* LCD-Data(22) */ + {OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)}, /* LCD-Data(23) */ + + {OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)}, /* LCD-VSync */ + {OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)}, /* LCD-HSync */ + {OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */ + {OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)}, /* LCD-CLK */ + + {-1}, +}; + +void enable_uart0_pin_mux(void) +{ + configure_module_pin_mux(uart0_pin_mux); +} + +void enable_i2c0_pin_mux(void) +{ + configure_module_pin_mux(i2c0_pin_mux); +} + +void enable_board_pin_mux(void) +{ + configure_module_pin_mux(i2c0_pin_mux); + configure_module_pin_mux(mii1_pin_mux); + configure_module_pin_mux(mii2_pin_mux); +#ifdef CONFIG_NAND + configure_module_pin_mux(nand_pin_mux); +#elif defined(CONFIG_MMC) + configure_module_pin_mux(mmc1_pin_mux); +#endif + configure_module_pin_mux(spi0_pin_mux); + configure_module_pin_mux(lcd_pin_mux); + configure_module_pin_mux(gpIOs); +} diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h index 703dbec..17c122c 100644 --- a/board/htkw/mcx/mcx.h +++ b/board/htkw/mcx/mcx.h @@ -325,8 +325,6 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(SYS_32K), (IEN | PTD | EN | M4)) \ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) \ MUX_VAL(CP(SYS_NIRQ), (IEN | PTD | EN | M4)) \ - MUX_VAL(CP(SYS_NRESWARM), (IEN | PTU | DIS | M4)) \ - /* SYS_nRESWARM */\ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) \ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) \ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) \ diff --git a/board/silica/pengwyn/Makefile b/board/silica/pengwyn/Makefile new file mode 100644 index 0000000..c8b4f9a --- /dev/null +++ b/board/silica/pengwyn/Makefile @@ -0,0 +1,13 @@ +# +# Makefile +# +# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ +# +# SPDX-License-Identifier: GPL-2.0+ +# + +ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_NOR_BOOT),y) +obj-y := mux.o +endif + +obj-y += board.o diff --git a/board/silica/pengwyn/board.c b/board/silica/pengwyn/board.c new file mode 100644 index 0000000..a553129 --- /dev/null +++ b/board/silica/pengwyn/board.c @@ -0,0 +1,207 @@ +/* + * board.c + * + * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/arch/cpu.h> +#include <asm/arch/hardware.h> +#include <asm/arch/ddr_defs.h> +#include <asm/arch/clock.h> +#include <asm/arch/sys_proto.h> +#include <i2c.h> +#include <phy.h> +#include <cpsw.h> +#include "board.h" + +DECLARE_GLOBAL_DATA_PTR; + +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; + +#if defined(CONFIG_SPL_BUILD) + +/* DDR3 RAM timings */ +static const struct ddr_data ddr3_data = { + .datardsratio0 = MT41K128MJT187E_RD_DQS, + .datawdsratio0 = MT41K128MJT187E_WR_DQS, + .datafwsratio0 = MT41K128MJT187E_PHY_FIFO_WE, + .datawrsratio0 = MT41K128MJT187E_PHY_WR_DATA, +}; + +static const struct cmd_control ddr3_cmd_ctrl_data = { + .cmd0csratio = MT41K128MJT187E_RATIO, + .cmd0iclkout = MT41K128MJT187E_INVERT_CLKOUT, + .cmd1csratio = MT41K128MJT187E_RATIO, + .cmd1iclkout = MT41K128MJT187E_INVERT_CLKOUT, + .cmd2csratio = MT41K128MJT187E_RATIO, + .cmd2iclkout = MT41K128MJT187E_INVERT_CLKOUT, +}; + +static struct emif_regs ddr3_emif_reg_data = { + .sdram_config = MT41K128MJT187E_EMIF_SDCFG, + .ref_ctrl = MT41K128MJT187E_EMIF_SDREF, + .sdram_tim1 = MT41K128MJT187E_EMIF_TIM1, + .sdram_tim2 = MT41K128MJT187E_EMIF_TIM2, + .sdram_tim3 = MT41K128MJT187E_EMIF_TIM3, + .zq_config = MT41K128MJT187E_ZQ_CFG, + .emif_ddr_phy_ctlr_1 = MT41K128MJT187E_EMIF_READ_LATENCY | + PHY_EN_DYN_PWRDN, +}; + +const struct ctrl_ioregs ddr3_ioregs = { + .cm0ioctl = MT41K128MJT187E_IOCTRL_VALUE, + .cm1ioctl = MT41K128MJT187E_IOCTRL_VALUE, + .cm2ioctl = MT41K128MJT187E_IOCTRL_VALUE, + .dt0ioctl = MT41K128MJT187E_IOCTRL_VALUE, + .dt1ioctl = MT41K128MJT187E_IOCTRL_VALUE, +}; + +#ifdef CONFIG_SPL_OS_BOOT +int spl_start_uboot(void) +{ + /* break into full u-boot on 'c' */ + return serial_tstc() && serial_getc() == 'c'; +} +#endif + +#define OSC (V_OSCK/1000000) +const struct dpll_params dpll_ddr_266 = { + 266, OSC-1, 1, -1, -1, -1, -1}; +const struct dpll_params dpll_ddr_303 = { + 303, OSC-1, 1, -1, -1, -1, -1}; +const struct dpll_params dpll_ddr_400 = { + 400, OSC-1, 1, -1, -1, -1, -1}; + +void am33xx_spl_board_init(void) +{ + /* + * The pengwyn board uses the TPS650250 PMIC without I2C + * interface and will output the following fixed voltages: + * DCDC1=3V3 (IO) DCDC2=1V5 (DDR) DCDC3=1V26 (Vmpu) + * VLDO1=1V8 (IO) VLDO2=1V8(IO) + * Vcore=1V1 is fixed, generated by TPS62231 + */ + + /* Get the frequency */ + dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); + + /* Set CORE Frequencies to OPP100 */ + do_setup_dpll(&dpll_core_regs, &dpll_core_opp100); + + /* 720MHz cpu, this might change on newer board revisions */ + dpll_mpu_opp100.m = MPUPLL_M_720; + do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100); +} + +const struct dpll_params *get_dpll_ddr_params(void) +{ + /* future configs can return other clock settings */ + return &dpll_ddr_303; +} + +void set_uart_mux_conf(void) +{ + enable_uart0_pin_mux(); +} + +void set_mux_conf_regs(void) +{ + enable_board_pin_mux(); +} + +void sdram_init(void) +{ + config_ddr(303, &ddr3_ioregs, &ddr3_data, + &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0); +} +#endif /* if CONFIG_SPL_BUILD */ + +/* + * Basic board specific setup. Pinmux has been handled already. + */ +int board_init(void) +{ + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + gpmc_init(); + return 0; +} + +#ifdef CONFIG_DRIVER_TI_CPSW +static void cpsw_control(int enabled) +{ + /* VTP can be added here */ + return; +} + +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x208, + .sliver_reg_ofs = 0xd80, + .phy_id = 0, + .phy_if = PHY_INTERFACE_MODE_MII, + }, + { + .slave_reg_ofs = 0x308, + .sliver_reg_ofs = 0xdc0, + .phy_id = 1, + .phy_if = PHY_INTERFACE_MODE_MII, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = CPSW_MDIO_BASE, + .cpsw_base = CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x800, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0xd00, + .ale_entries = 1024, + .host_port_reg_ofs = 0x108, + .hw_stats_reg_ofs = 0x900, + .bd_ram_ofs = 0x2000, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_2, +}; + +int board_eth_init(bd_t *bis) +{ + int rv, n = 0; + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + + if (!eth_getenv_enetaddr("ethaddr", mac_addr)) { + printf("<ethaddr> not set. Reading from E-fuse\n"); + /* try reading mac address from efuse */ + mac_lo = readl(&cdev->macid0l); + mac_hi = readl(&cdev->macid0h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("ethaddr", mac_addr); + else + return n; + } + + writel(MII_MODE_ENABLE, &cdev->miisel); + + rv = cpsw_register(&cpsw_data); + if (rv < 0) + printf("Error %d registering CPSW switch\n", rv); + else + n += rv; + return n; +} +#endif /* if CONFIG_DRIVER_TI_CPSW */ diff --git a/board/silica/pengwyn/board.h b/board/silica/pengwyn/board.h new file mode 100644 index 0000000..05addf6 --- /dev/null +++ b/board/silica/pengwyn/board.h @@ -0,0 +1,15 @@ +/* + * board.h + * + * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +void enable_uart0_pin_mux(void); +void enable_board_pin_mux(void); + +#endif diff --git a/board/silica/pengwyn/mux.c b/board/silica/pengwyn/mux.c new file mode 100644 index 0000000..c8be440 --- /dev/null +++ b/board/silica/pengwyn/mux.c @@ -0,0 +1,98 @@ +/* + * mux.c + * + * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/hardware.h> +#include <asm/arch/mux.h> +#include <asm/io.h> +#include "board.h" + +/* UART0 pins E15(rx),E16(tx) [E17(rts),E18(cts)] */ +static struct module_pin_mux uart0_pin_mux[] = { + {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */ + {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */ + {-1}, +}; + +/* unused: UART1 pins D15(tx),D16(rx),D17(cts),D18(rts) */ + +/* I2C pins C16(scl)/C17(sda) */ +static struct module_pin_mux i2c0_pin_mux[] = { + {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | + PULLUDEN | SLEWCTRL)}, /* I2C0_DATA */ + {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | + PULLUDEN | SLEWCTRL)}, /* I2C0_SCLK */ + {-1}, +}; + +/* MMC0 pins */ +static struct module_pin_mux mmc0_pin_mux[] = { + {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */ + {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */ + {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */ + {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */ + {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */ + {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */ + {OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */ + {-1}, +}; + +/* MII pins */ +static struct module_pin_mux mii1_pin_mux[] = { + {OFFSET(mii1_rxerr), MODE(0) | RXACTIVE}, /* MII1_RXERR */ + {OFFSET(mii1_txen), MODE(0)}, /* MII1_TXEN */ + {OFFSET(mii1_rxdv), MODE(0) | RXACTIVE}, /* MII1_RXDV */ + {OFFSET(mii1_txd3), MODE(0)}, /* MII1_TXD3 */ + {OFFSET(mii1_txd2), MODE(0)}, /* MII1_TXD2 */ + {OFFSET(mii1_txd1), MODE(0)}, /* MII1_TXD1 */ + {OFFSET(mii1_txd0), MODE(0)}, /* MII1_TXD0 */ + {OFFSET(mii1_txclk), MODE(0) | RXACTIVE}, /* MII1_TXCLK */ + {OFFSET(mii1_rxclk), MODE(0) | RXACTIVE}, /* MII1_RXCLK */ + {OFFSET(mii1_rxd3), MODE(0) | RXACTIVE}, /* MII1_RXD3 */ + {OFFSET(mii1_rxd2), MODE(0) | RXACTIVE}, /* MII1_RXD2 */ + {OFFSET(mii1_rxd1), MODE(0) | RXACTIVE}, /* MII1_RXD1 */ + {OFFSET(mii1_rxd0), MODE(0) | RXACTIVE}, /* MII1_RXD0 */ + {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */ + {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ + {-1}, +}; + +/* NAND pins */ +static struct module_pin_mux nand_pin_mux[] = { + {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */ + {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */ + {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */ + {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */ + {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */ + {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */ + {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */ + {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */ + {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */ + {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */ + {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */ + {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */ + {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */ + {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */ + {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */ + {-1}, +}; + +void enable_uart0_pin_mux(void) +{ + configure_module_pin_mux(uart0_pin_mux); +} + +void enable_board_pin_mux() +{ + configure_module_pin_mux(i2c0_pin_mux); + configure_module_pin_mux(uart0_pin_mux); + configure_module_pin_mux(mii1_pin_mux); + configure_module_pin_mux(mmc0_pin_mux); + configure_module_pin_mux(nand_pin_mux); +} diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c index 4e6846a..95fd137 100644 --- a/board/ti/am43xx/board.c +++ b/board/ti/am43xx/board.c @@ -346,14 +346,14 @@ static void enable_vtt_regulator(void) u32 temp; /* enable module */ - writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO0_BASE + OMAP_GPIO_CTRL); - - /* enable output for GPIO0_22 */ - writel(GPIO_SETDATAOUT(GPIO_22), - AM33XX_GPIO0_BASE + OMAP_GPIO_SETDATAOUT); - temp = readl(AM33XX_GPIO0_BASE + OMAP_GPIO_OE); - temp = temp & ~(GPIO_OE_ENABLE(GPIO_22)); - writel(temp, AM33XX_GPIO0_BASE + OMAP_GPIO_OE); + writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO5_BASE + OMAP_GPIO_CTRL); + + /* enable output for GPIO5_7 */ + writel(GPIO_SETDATAOUT(7), + AM33XX_GPIO5_BASE + OMAP_GPIO_SETDATAOUT); + temp = readl(AM33XX_GPIO5_BASE + OMAP_GPIO_OE); + temp = temp & ~(GPIO_OE_ENABLE(7)); + writel(temp, AM33XX_GPIO5_BASE + OMAP_GPIO_OE); } void sdram_init(void) diff --git a/board/ti/am43xx/mux.c b/board/ti/am43xx/mux.c index 810b194..51f7fd6 100644 --- a/board/ti/am43xx/mux.c +++ b/board/ti/am43xx/mux.c @@ -33,8 +33,8 @@ static struct module_pin_mux i2c0_pin_mux[] = { {-1}, }; -static struct module_pin_mux gpio0_22_pin_mux[] = { - {OFFSET(ddr_ba2), (MODE(9) | PULLUP_EN)}, /* GPIO0_22 */ +static struct module_pin_mux gpio5_7_pin_mux[] = { + {OFFSET(spi0_cs0), (MODE(7) | PULLUP_EN)}, /* GPIO5_7 */ {-1}, }; @@ -49,7 +49,7 @@ void enable_board_pin_mux(void) configure_module_pin_mux(i2c0_pin_mux); if (board_is_gpevm()) - configure_module_pin_mux(gpio0_22_pin_mux); + configure_module_pin_mux(gpio5_7_pin_mux); } void enable_i2c0_pin_mux(void) @@ -256,6 +256,11 @@ Active arm armv7 am33xx phytec pcm051 Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <r.meier@siemens.com> Active arm armv7 am33xx siemens pxm2 pxm2 - Roger Meier <r.meier@siemens.com> Active arm armv7 am33xx siemens rut rut - Roger Meier <r.meier@siemens.com> +Active arm armv7 am33xx silica pengwyn pengwyn - Lothar Felten <lothar.felten@gmail.com> +Active arm armv7 am33xx BuR tseries tseries_nand tseries:SERIAL1,CONS_INDEX=1,NAND Hannes Petermaier <hannes.petermaier@br-automation.com> +Active arm armv7 am33xx BuR tseries tseries_mmc tseries:SERIAL1,CONS_INDEX=1,EMMC_BOOT Hannes Petermaier <hannes.petermaier@br-automation.com> +Active arm armv7 am33xx BuR tseries tseries_spi tseries:SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT Hannes Petermaier <hannes.petermaier@br-automation.com> +Active arm armv7 am33xx BuR kwb kwb kwb:SERIAL1,CONS_INDEX=1 Hannes Petermaier <hannes.petermaier@br-automation.com> Active arm armv7 am33xx ti am335x am335x_boneblack am335x_evm:SERIAL1,CONS_INDEX=1,EMMC_BOOT Tom Rini <trini@ti.com> Active arm armv7 am33xx ti am335x am335x_evm am335x_evm:SERIAL1,CONS_INDEX=1,NAND Tom Rini <trini@ti.com> Active arm armv7 am33xx ti am335x am335x_evm_nor am335x_evm:SERIAL1,CONS_INDEX=1,NAND,NOR Tom Rini <trini@ti.com> diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 73a9adb..59a8f36 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -20,6 +20,7 @@ #define MACH_TYPE_TIAM335EVM 3589 /* Until the next sync */ #define CONFIG_MACH_TYPE MACH_TYPE_TIAM335EVM +#define CONFIG_BOARD_LATE_INIT /* Clock Defines */ #define V_OSCK 24000000 /* Clock output from T2 */ @@ -31,6 +32,12 @@ /* Always 128 KiB env size */ #define CONFIG_ENV_SIZE (128 << 10) +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + #ifdef CONFIG_NAND #define NANDARGS \ "mtdids=" MTDIDS_DEFAULT "\0" \ @@ -64,6 +71,9 @@ "bootfile=zImage\0" \ "fdtfile=undefined\0" \ "console=ttyO0,115200n8\0" \ + "partitions=" \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \ "optargs=\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 ro\0" \ @@ -295,6 +305,9 @@ #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT) /* disable host part of MUSB in SPL */ #undef CONFIG_MUSB_HOST +/* disable EFI partitions and partition UUID support */ +#undef CONFIG_PARTITION_UUIDS +#undef CONFIG_EFI_PARTITION /* * Disable CPSW SPL support so we fit within the 101KiB limit. */ diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h index d3c4756..9b4716f 100644 --- a/include/configs/am43xx_evm.h +++ b/include/configs/am43xx_evm.h @@ -84,6 +84,12 @@ #define CONFIG_OMAP_USB_PHY #define CONFIG_AM437X_USB2PHY2_HOST +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + #ifndef CONFIG_SPL_BUILD #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x80200000\0" \ @@ -95,6 +101,9 @@ "bootdir=/boot\0" \ "bootfile=zImage\0" \ "console=ttyO0,115200n8\0" \ + "partitions=" \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \ "optargs=\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h new file mode 100644 index 0000000..1f57bd2 --- /dev/null +++ b/include/configs/bur_am335x_common.h @@ -0,0 +1,197 @@ +/* + * bur_am335x_common.h + * + * common parts used by B&R AM335x based boards + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __BUR_AM335X_COMMON_H__ +#define __BUR_AM335X_COMMON_H__ +/* ------------------------------------------------------------------------- */ +#define CONFIG_AM33XX +#define CONFIG_OMAP +#define CONFIG_OMAP_COMMON +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_SYS_CACHELINE_SIZE 64 +#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ + +/* Timer information */ +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ + +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_POWER_TPS65217 + +#define CONFIG_SYS_NO_FLASH /* have no NOR-flash */ + +#include <asm/arch/omap.h> + +/* NS16550 Configuration */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK 48000000 +#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ +#define CONFIG_BAUDRATE 115200 + +/* Network defines */ +#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ +#define CONFIG_CMD_DHCP +#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 4 +#define CONFIG_CMD_PING +#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */ +#define CONFIG_MII /* Required in net/eth.c */ +#define CONFIG_SPL_ETH_SUPPORT +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 1 +#define CONFIG_PHY_NATSEMI +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */ +#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" + +/* + * SPL related defines. The Public RAM memory map the ROM defines the + * area between 0x402F0400 and 0x4030B800 as a download area and + * 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also + * supports X-MODEM loading via UART, and we leverage this and then use + * Y-MODEM to load u-boot.img, when booted over UART. + */ +#define CONFIG_SPL_TEXT_BASE 0x402F0400 +#define CONFIG_SPL_MAX_SIZE (0x4030B800 - CONFIG_SPL_TEXT_BASE) + +/* + * Since SPL did pll and ddr initialization for us, + * we don't need to do it twice. + */ +#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT) +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif /* !CONFIG_SPL_BUILD, ... */ +/* + * Our DDR memory always starts at 0x80000000 and U-Boot shall have + * relocated itself to higher in memory by the time this value is used. + */ +#define CONFIG_SYS_LOAD_ADDR 0x80000000 +/* + * ---------------------------------------------------------------------------- + * DDR information. We say (for simplicity) that we have 1 bank, + * always, even when we have more. We always start at 0x80000000, + * and we place the initial stack pointer in our SRAM. + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ + GENERATED_GBL_DATA_SIZE) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX + +/* GPIO */ +#define CONFIG_OMAP_GPIO +#define CONFIG_CMD_GPIO +/* + * ---------------------------------------------------------------------------- + * The following are general good-enough settings for U-Boot. We set a + * large malloc pool as we generally have a lot of DDR, and we opt for + * function over binary size in the main portion of U-Boot as this is + * generally easily constrained later if needed. We enable the config + * options that give us information in the environment about what board + * we are on so we do not need to rely on the command prompt. We set a + * console baudrate of 115200 and use the default baud rate table. + */ +#define CONFIG_SYS_MALLOC_LEN (1024 << 10) +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# " +#define CONFIG_SYS_CONSOLE_INFO_QUIET +#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */ + +/* As stated above, the following choices are optional. */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_VERSION_VARIABLE + +/* We set the max number of command args high to avoid HUSH bugs. */ +#define CONFIG_SYS_MAXARGS 64 + +/* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 512 +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\ + sizeof(CONFIG_SYS_PROMPT) + 16) +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* + * For commands to use, we take the default list and add a few other + * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH + * prior to this include, in order to skip a few commands. When we do + * have flash, if we expect these commands they must be enabled in that + * config. If desired, a specific list of desired commands can be used + * instead. + */ +#include <config_cmd_default.h> +/* undefine commands, which we do not need */ +#undef CONFIG_CMD_EDITENV +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_ITEST +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_NFS +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_XIMG +#undef CONFIG_CMD_CRC32 +/* define command we need always */ +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_SOURCE + +/* + * Our platforms make use of SPL to initalize the hardware (primarily + * memory) enough for full U-Boot to be loaded. We also support Falcon + * Mode so that the Linux kernel can be booted directly from SPL + * instead, if desired. We make use of the general SPL framework found + * under common/spl/. Given our generally common memory map, we set a + * number of related defaults and sizes here. + */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +/* + * Place the image at the start of the ROM defined image space. + * We limit our size to the ROM-defined downloaded image area, and use the + * rest of the space for stack. We load U-Boot itself into memory at + * 0x80800000 for legacy reasons (to not conflict with older SPLs). We + * have our BSS be placed 1MiB after this, to allow for the default + * Linux kernel address of 0x80008000 to work, in the Falcon Mode case. + * We have the SPL malloc pool at the end of the BSS area. + * + * ---------------------------------------------------------------------------- + */ +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#undef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0x80800000 +#define CONFIG_SPL_BSS_START_ADDR 0x80A00000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ + CONFIG_SPL_BSS_MAX_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN + +/* General parts of the framework, required. */ +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_YMODEM_SUPPORT +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#endif /* ! __BUR_AM335X_COMMON_H__ */ diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index 7729a02..08c67f5 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -45,13 +45,6 @@ #define CONFIG_MISC_INIT_R #define CONFIG_OF_LIBFDT 1 -/* - * The early kernel mapping on ARM currently only maps from the base of DRAM - * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000. - * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000, - * so that leaves DRAM base to DRAM base + 0x4000 available. - */ -#define CONFIG_SYS_BOOTMAPSZ 0x4000 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_SETUP_MEMORY_TAGS diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index 86574c8..c67cf60 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -34,8 +34,19 @@ #define CONFIG_SYS_OMAP_ABE_SYSCK +/* Define the default GPT table for eMMC */ +#define PARTS_DEFAULT \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}" + #include <configs/ti_omap5_common.h> +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + /* CPSW Ethernet */ #define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ #define CONFIG_CMD_DHCP diff --git a/include/configs/kwb.h b/include/configs/kwb.h new file mode 100644 index 0000000..0f631c0 --- /dev/null +++ b/include/configs/kwb.h @@ -0,0 +1,128 @@ +/* + * kwb.h + * + * specific parts for B&R KWB Motherboard + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_KWB_H__ +#define __CONFIG_KWB_H__ + +#include <configs/bur_am335x_common.h> +/* ------------------------------------------------------------------------- */ +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_POWER_TPS65217 + +#define CONFIG_MACH_TYPE 3589 +/* I2C IP block */ +#define CONFIG_SYS_OMAP24_I2C_SPEED_PSOC 20000 + +/* GPIO */ +#define CONFIG_SPL_GPIO_SUPPORT + +/* MMC/SD IP block */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_OMAP_HSMMC +#define CONFIG_CMD_MMC +#define CONFIG_SUPPORT_EMMC_BOOT +/* RAW SD card / eMMC locations. */ +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SPL_MMC_SUPPORT + +#undef CONFIG_SPL_OS_BOOT +#ifdef CONFIG_SPL_OS_BOOT +#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 + +/* RAW SD card / eMMC */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ + +#endif /* CONFIG_SPL_OS_BOOT */ + +/* Always 128 KiB env size */ +#define CONFIG_ENV_SIZE (128 << 10) + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=0\0" \ + "loadaddr=0x80100000\0" \ + "bootfile=arimg\0" \ + "usbboot=echo Booting from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 ${loadaddr} ${bootfile}; " \ + "usb stop; " \ + "go ${loadaddr};\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload 0; " \ + "dhcp; " \ + "tftp ${loadaddr} arimg; " \ + "go ${loadaddr}\0" \ + "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 0x80000000 updateubootusb.img; " \ + "source;\0" \ + "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ + "setenv autoload 0; " \ + "dhcp;" \ + "tftp 0x80000000 updateUBOOT.img;" \ + "source;\0" +#endif /* !CONFIG_SPL_BUILD*/ + +#define CONFIG_BOOTCOMMAND \ + "run usbupdate;" +#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */ + +/* undefine command which we not need here */ +#undef CONFIG_BOOTM_LINUX +#undef CONFIG_BOOTM_NETBSD +#undef CONFIG_BOOTM_PLAN9 +#undef CONFIG_BOOTM_RTEMS +#undef CONFIG_GZIP +#undef CONFIG_ZLIB +#undef CONFIG_CMD_CRC32 + +/* USB configuration */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +/* attention! not only for gadget, enables also highspeed in hostmode */ +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_HOST + +#ifdef CONFIG_MUSB_HOST +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif /* CONFIG_MUSB_HOST */ + +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_PART 2 +#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +/* + * Common filesystems support. When we have removable storage we + * enabled a number of useful commands and support. + */ +#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_FS_GENERIC +#endif /* CONFIG_MMC, ... */ + +#endif /* ! __CONFIG_TSERIES_H__ */ diff --git a/include/configs/mcx.h b/include/configs/mcx.h index dcd29ce..7c5c2f4 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -98,6 +98,7 @@ /* EHCI */ #define CONFIG_USB_STORAGE +#define CONFIG_OMAP3_GPIO_2 #define CONFIG_OMAP3_GPIO_5 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP @@ -263,10 +264,9 @@ "${mtdparts} " \ "vram=6M omapfb.vram=1:2M,2:2M,3:2M " \ "omapdss.def_disp=lcd;" \ - "bootm 0x82000000 0x84000000\0" - -#define CONFIG_BOOTCOMMAND \ - "run nandboot" + "bootm 0x82000000 0x84000000\0" \ + "bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;" \ + "then source 82000000;else run nandboot;fi\0" #define CONFIG_AUTO_COMPLETE #define CONFIG_CMDLINE_EDITING @@ -395,6 +395,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 256 #define CONFIG_SYS_NAND_ECCBYTES 3 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW +#define CONFIG_SPL_NAND_SOFTECC #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h new file mode 100644 index 0000000..5a55556 --- /dev/null +++ b/include/configs/pengwyn.h @@ -0,0 +1,208 @@ +/* + * pengwyn.h + * + * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com> + * + * based on am335x_evm.h, Copyright (C) 2011 Texas Instruments Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_PENGWYN_H +#define __CONFIG_PENGWYN_H + +#define CONFIG_NAND +#define CONFIG_SERIAL1 +#define CONFIG_CONS_INDEX 1 + +#include <configs/ti_am335x_common.h> + +/* Clock Defines */ +#define V_OSCK 24000000 +#define V_SCLK V_OSCK + +/* set env size */ +#define CONFIG_ENV_SIZE 0x4000 + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x80200000\0" \ + "fdtaddr=0x80F80000\0" \ + "bootpart=0:2\0" \ + "bootdir=/boot\0" \ + "bootfile=zImage\0" \ + "fdtfile=am335x-pengwyn.dtb\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 ro\0" \ + "mmcrootfstype=ext4 rootwait\0" \ + "rootpath=/export/rootfs\0" \ + "nfsopts=nolock\0" \ + "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \ + "::off\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ + "ip=dhcp\0" \ + "bootenv=uEnv.txt\0" \ + "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ + "importbootenv=echo Importing environment from mmc ...; " \ + "env import -t $loadaddr $filesize\0" \ + "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ + "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ + "mmcloados=run mmcargs; " \ + "bootz ${loadaddr} - ${fdtaddr};\0" \ + "mmcboot=mmc dev ${mmcdev}; " \ + "if mmc rescan; then " \ + "echo SD/MMC found on device ${mmcdev};" \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run loadimage; then " \ + "run loadfdt;" \ + "run mmcloados;" \ + "fi;" \ + "fi;\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload no; " \ + "dhcp; " \ + "tftp ${loadaddr} ${bootfile}; " \ + "tftp ${fdtaddr} ${fdtfile}; " \ + "run netargs; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "nandargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${nandroot} " \ + "rootfstype=${nandrootfstype}\0" \ + "nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \ + "nandrootfstype=ubifs rootwait=1\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nand read ${fdtaddr} u-boot-spl-os; " \ + "nand read ${loadaddr} kernel; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" +#endif + +#define CONFIG_BOOTCOMMAND \ + "run mmcboot;" \ + "run nandboot;" + +/* NS16550 Configuration: primary UART via FDTI */ +#define CONFIG_SYS_NS16550_COM1 0x44e09000 +#define CONFIG_BAUDRATE 115200 + +/* I2C Configuration */ +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_CMD_EEPROM +#define CONFIG_ENV_EEPROM_IS_ON_I2C +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_MULTI_EEPROMS + +/* SPL */ +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_YMODEM_SUPPORT + +/* General network SPL */ +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" + +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_NAND_OMAP_ELM +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 +#define CONFIG_SYS_NAND_ONFI_DETECTION +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define GPMC_NAND_ECC_LP_x8_LAYOUT 1 +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \ + "128k(SPL.backup1)," \ + "128k(SPL.backup2)," \ + "128k(SPL.backup3),1792k(u-boot)," \ + "128k(u-boot-spl-os)," \ + "128k(u-boot-env),5m(kernel),-(rootfs)" +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */ +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ + +/* + * USB configuration. We enable MUSB support, both for host and for + * gadget. We set USB0 as peripheral and USB1 as host, based on the + * board schematic and physical port wired to each. Then for host we + * add mass storage support. + */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_GADGET +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_VBUS_DRAW 2 +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST + +#if defined(CONFIG_MUSB_HOST) +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_SPL_BUILD) +/* disable host part of MUSB in SPL */ +#undef CONFIG_MUSB_HOST +/* Disable CPSW SPL support so we fit within the 101KiB limit. */ +#undef CONFIG_SPL_ETH_SUPPORT +#endif + +/* Network */ +#define CONFIG_CMD_MII +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 1 +#define CONFIG_PHY_RESET 1 +#define CONFIG_PHY_NATSEMI + +/* CPSW support */ +#define CONFIG_SPL_ETH_SUPPORT + +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#endif /* ! __CONFIG_PENGWYN_H */ diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h index 9abfe82..9c04c23 100644 --- a/include/configs/tao3530.h +++ b/include/configs/tao3530.h @@ -83,6 +83,13 @@ #define CONFIG_OMAP_HSMMC #define CONFIG_DOS_PARTITION +/* GPIO banks */ +#define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */ +#define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */ +#define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */ +#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ +#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ + /* commands to include */ #include <config_cmd_default.h> diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index 91f97dd..7e9ca01 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -13,7 +13,6 @@ #define __CONFIG_TI_AM335X_COMMON_H__ #define CONFIG_AM33XX -#define CONFIG_BOARD_LATE_INIT #define CONFIG_ARCH_CPU_INIT #define CONFIG_SYS_CACHELINE_SIZE 64 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h index 2f0e4c0..bcb5eab 100644 --- a/include/configs/ti_omap4_common.h +++ b/include/configs/ti_omap4_common.h @@ -163,4 +163,10 @@ #define CONFIG_SPL_NAND_AM33XX_BCH /* ELM support */ #endif +#ifdef CONFIG_SPL_BUILD +/* No need for i2c in SPL mode as we will use SRI2C for PMIC access on OMAP4 */ +#undef CONFIG_SYS_I2C +#undef CONFIG_SYS_I2C_OMAP24XX +#endif + #endif /* __CONFIG_TI_OMAP4_COMMON_H */ diff --git a/include/configs/tseries.h b/include/configs/tseries.h new file mode 100644 index 0000000..8fb87ac --- /dev/null +++ b/include/configs/tseries.h @@ -0,0 +1,265 @@ +/* + * tseries.h + * + * specific parts for B&R T-Series Motherboard + * + * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_TSERIES_H__ +#define __CONFIG_TSERIES_H__ + +#include <configs/bur_am335x_common.h> +/* ------------------------------------------------------------------------- */ +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_POWER_TPS65217 + +/* Support both device trees and ATAGs. */ +#define CONFIG_OF_LIBFDT +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_CMD_BOOTZ +/*#define CONFIG_MACH_TYPE 3589*/ +#define CONFIG_MACH_TYPE 0xFFFFFFFF /* TODO: check with kernel*/ + +/* MMC/SD IP block */ +#if defined(CONFIG_EMMC_BOOT) + #define CONFIG_MMC + #define CONFIG_GENERIC_MMC + #define CONFIG_OMAP_HSMMC + #define CONFIG_CMD_MMC + #define CONFIG_SUPPORT_EMMC_BOOT +/* RAW SD card / eMMC locations. */ + #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */ + #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ + #define CONFIG_SPL_MMC_SUPPORT +#endif /* CONFIG_EMMC_BOOT */ + +/* + * When we have SPI or NAND flash we expect to be making use of mtdparts, + * both for ease of use in U-Boot and for passing information on to + * the Linux kernel. + */ +#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND) +#define CONFIG_MTD_DEVICE /* Required for mtdparts */ +#define CONFIG_CMD_MTDPARTS +#endif /* CONFIG_SPI_BOOT, ... */ + +#undef CONFIG_SPL_OS_BOOT +#ifdef CONFIG_SPL_OS_BOOT +#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 + +/* RAW SD card / eMMC */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ + +/* NAND */ +#ifdef CONFIG_NAND +#define CONFIG_CMD_SPL_NAND_OFS 0x080000 /* end of u-boot */ +#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x140000 +#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000 +#endif /* CONFIG_NAND */ +#endif /* CONFIG_SPL_OS_BOOT */ + +#ifdef CONFIG_NAND +#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */ +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 +#endif /* CONFIG_NAND */ + +/* Always 128 KiB env size */ +#define CONFIG_ENV_SIZE (128 << 10) + +#ifdef CONFIG_NAND +#define NANDARGS \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "nandargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${nandroot} " \ + "rootfstype=${nandrootfstype}\0" \ + "nandroot=ubi0:rootfs rw ubi.mtd=8,2048\0" \ + "nandrootfstype=ubifs rootwait=1\0" \ + "nandimgsize=0x500000\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nand read ${loadaddr} kernel ${nandimgsize}; " \ + "bootz ${loadaddr}\0" +#else +#define NANDARGS "" +#endif /* CONFIG_NAND */ + +#ifdef CONFIG_MMC +#define MMCARGS \ + "silent=1\0" +#else +#define MMCARGS "" +#endif /* CONFIG_MMC */ + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=0\0" \ + "loadaddr=0x80200000\0" \ + "bootfile=zImage\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "rootpath=/tftpboot/tseries/rootfs-small\0" \ + "nfsopts=nolock\0" \ + "netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ + "ip=dhcp\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload no; " \ + "dhcp; " \ + "tftp ${loadaddr} ${bootfile}; " \ + "run netargs; " \ + "bootm ${loadaddr}\0" \ + "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 0x80000000 updateubootusb.img; " \ + "source;\0" \ + "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ + "setenv autoload 0; " \ + "dhcp;" \ + "tftp 0x80000000 updateUBOOT.img;" \ + "source;\0" \ + NANDARGS \ + MMCARGS +#endif /* !CONFIG_SPL_BUILD*/ + +#define CONFIG_BOOTCOMMAND \ + "run mmcboot1;" +#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */ + +#ifdef CONFIG_NAND +/* + * GPMC block. We support 1 device and the physical address to + * access CS0 at is 0x8000000. + */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x8000000 +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_CMD_NAND +/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */ +#define CONFIG_NAND_OMAP_ELM +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW +#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \ + "128k(SPL)," \ + "128k(SPL.backup1)," \ + "128k(SPL.backup2)," \ + "128k(SPL.backup3)," \ + "512k(u-boot)," \ + "128k(u-boot-spl-os)," \ + "128k(u-boot-env)," \ + "5m(kernel),"\ + "-(rootfs)" +#endif /* CONFIG_NAND */ + +/* USB configuration */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +/* attention! not only for gadget, enables also highspeed in hostmode */ +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_HOST +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST + +#ifdef CONFIG_MUSB_HOST +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif /* CONFIG_MUSB_HOST */ + +#if defined(CONFIG_SPI_BOOT) +/* McSPI IP block */ +#define CONFIG_SPI +#define CONFIG_OMAP3_SPI +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SF_DEFAULT_SPEED 24000000 + +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */ +#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */ +#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */ + +#elif defined(CONFIG_EMMC_BOOT) +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_PART 2 +#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#elif defined(CONFIG_NAND) +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x120000 /* TODO: Adresse definieren */ +#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE +#else +#error "no storage for Environment defined!" +#endif +/* + * Common filesystems support. When we have removable storage we + * enabled a number of useful commands and support. + */ +#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_FS_GENERIC +#endif /* CONFIG_MMC, ... */ + +#endif /* ! __CONFIG_TSERIES_H__ */ |