diff options
| -rw-r--r-- | drivers/video/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/video/ssd2828.c | 20 | ||||
| -rw-r--r-- | drivers/video/ssd2828.h | 11 |
3 files changed, 28 insertions, 7 deletions
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index ec14a37..d9d4afc 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -19,12 +19,14 @@ config VIDEO_LCD_SSD2828 config VIDEO_LCD_SSD2828_TX_CLK int "SSD2828 TX_CLK frequency (in MHz)" depends on VIDEO_LCD_SSD2828 + default 0 ---help--- The frequency of the crystal, which is clocking SSD2828. It may be anything in the 8MHz-30MHz range and the exact value should be retrieved from the board schematics. Or in the case of Allwinner hardware, it can be usually found as 'lcd_xtal_freq' variable in - FEX files. + FEX files. It can be also set to 0 for selecting PCLK from the + parallel LCD interface instead of TX_CLK as the PLL clock source. config VIDEO_LCD_SSD2828_RESET string "RESET pin of SSD2828" diff --git a/drivers/video/ssd2828.c b/drivers/video/ssd2828.c index be68d38..8b09082 100644 --- a/drivers/video/ssd2828.c +++ b/drivers/video/ssd2828.c @@ -340,7 +340,7 @@ static int ssd2828_configure_video_interface(const struct ssd2828_config *cfg, int ssd2828_init(const struct ssd2828_config *cfg, const struct ctfb_res_modes *mode) { - u32 lp_div, pll_freq_kbps, pll_config; + u32 lp_div, pll_freq_kbps, reference_freq_khz, pll_config; /* The LP clock speed is limited by 10MHz */ const u32 mipi_dsi_low_power_clk_khz = 10000; /* @@ -374,6 +374,20 @@ int ssd2828_init(const struct ssd2828_config *cfg, } /* + * Pick the reference clock for PLL. If we know the exact 'tx_clk' + * clock speed, then everything is good. If not, then we can fallback + * to 'pclk' (pixel clock from the parallel LCD interface). In the + * case of using this fallback, it is necessary to have parallel LCD + * already initialized and running at this point. + */ + reference_freq_khz = cfg->ssd2828_tx_clk_khz; + if (reference_freq_khz == 0) { + reference_freq_khz = mode->pixclock_khz; + /* Use 'pclk' as the reference clock for PLL */ + cfgr_reg |= SSD2828_CFGR_CSS; + } + + /* * Setup the parallel LCD timings in the appropriate registers. */ if (ssd2828_configure_video_interface(cfg, mode) != 0) { @@ -390,10 +404,10 @@ int ssd2828_init(const struct ssd2828_config *cfg, /* PLL Configuration Register */ pll_config = construct_pll_config( cfg->mipi_dsi_bitrate_per_data_lane_mbps * 1000, - cfg->ssd2828_tx_clk_khz); + reference_freq_khz); write_hw_register(cfg, SSD2828_PLCR, pll_config); - pll_freq_kbps = decode_pll_config(pll_config, cfg->ssd2828_tx_clk_khz); + pll_freq_kbps = decode_pll_config(pll_config, reference_freq_khz); lp_div = DIV_ROUND_UP(pll_freq_kbps, mipi_dsi_low_power_clk_khz * 8); /* VC Control Register */ diff --git a/drivers/video/ssd2828.h b/drivers/video/ssd2828.h index 14b96c5..1af6fa4 100644 --- a/drivers/video/ssd2828.h +++ b/drivers/video/ssd2828.h @@ -47,8 +47,12 @@ struct ssd2828_config { * to TX_CLK_XIO/TX_CLK_XIN pins), which is necessary at least for * clocking SPI after reset. The exact clock speed is not strictly, * defined, but the datasheet says that it must be somewhere in the - * 8MHz - 30MHz range (see "TX_CLK Timing" section). It is used as - * a reference clock for PLL and must be set correctly. + * 8MHz - 30MHz range (see "TX_CLK Timing" section). It can be also + * used as a reference clock for PLL. If the exact clock frequency + * is known, then it can be specified here. If it is unknown, or the + * information is not trustworthy, then it can be set to 0. + * + * If unsure, set to 0. */ int ssd2828_tx_clk_khz; @@ -115,7 +119,8 @@ struct ssd2828_config { * The right place to insert this function call is after the parallel LCD * interface is initialized and before turning on the backlight. This is * advised in the "Example for system sleep in and out" section of the - * SSD2828 datasheet. + * SSD2828 datasheet. And also SS2828 may use 'pclk' as the clock source + * for PLL, which means that the input signal must be already there. */ int ssd2828_init(const struct ssd2828_config *cfg, const struct ctfb_res_modes *mode); |