summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--board/eNET/eNET.c17
-rw-r--r--board/eNET/eNET_start.S7
-rw-r--r--include/configs/eNET.h291
3 files changed, 129 insertions, 186 deletions
diff --git a/board/eNET/eNET.c b/board/eNET/eNET.c
index 8e11acf..e64a395 100644
--- a/board/eNET/eNET.c
+++ b/board/eNET/eNET.c
@@ -35,16 +35,6 @@
DECLARE_GLOBAL_DATA_PTR;
-#undef SC520_CDP_DEBUG
-
-#ifdef SC520_CDP_DEBUG
-#define PRINTF(fmt,args...) printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-unsigned long monitor_flash_len = CONFIG_SYS_MONITOR_LEN;
-
static void enet_timer_isr(void);
static void enet_toggle_run_led(void);
static void enet_setup_pars(void);
@@ -199,22 +189,23 @@ int last_stage_init(void)
outb(0x00, LED_LATCH_ADDRESS);
- register_timer_isr (enet_timer_isr);
+ register_timer_isr(enet_timer_isr);
printf("Serck Controls eNET\n");
return 0;
}
-ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
{
if (banknum == 0) { /* non-CFI boot flash */
info->portwidth = FLASH_CFI_8BIT;
info->chipwidth = FLASH_CFI_BY8;
info->interface = FLASH_CFI_X8;
return 1;
- } else
+ } else {
return 0;
+ }
}
int board_eth_init(bd_t *bis)
diff --git a/board/eNET/eNET_start.S b/board/eNET/eNET_start.S
index 137fe41..1b3d289 100644
--- a/board/eNET/eNET_start.S
+++ b/board/eNET/eNET_start.S
@@ -29,10 +29,3 @@ early_board_init:
/* No 32-bit board specific initialisation */
jmp early_board_init_ret
-.globl cpu_halt_asm
-cpu_halt_asm:
- movb $0x0f, %al
- movw $LED_LATCH_ADDRESS, %dx
- outb %al, %dx
- hlt
- jmp cpu_halt_asm
diff --git a/include/configs/eNET.h b/include/configs/eNET.h
index faeb52f..506f4c1 100644
--- a/include/configs/eNET.h
+++ b/include/configs/eNET.h
@@ -30,123 +30,113 @@
#define __CONFIG_H
/*
- * Stuff still to be dealt with -
- */
-#define CONFIG_RTC_MC146818
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0
-
-/*
* High Level Configuration Options
* (easy to change)
*/
-#define DEBUG_PARSER
-
-#define CONFIG_X86 1 /* Intel X86 CPU */
-#define CONFIG_SYS_SC520 1 /* AMD SC520 */
+#define CONFIG_X86
+#define CONFIG_SYS_SC520
#define CONFIG_SYS_SC520_SSI
-#define CONFIG_SHOW_BOOT_PROGRESS 1
-#define CONFIG_LAST_STAGE_INIT 1
+#define CONFIG_SHOW_BOOT_PROGRESS
+#define CONFIG_LAST_STAGE_INIT
-/*
- * If CONFIG_HW_WATCHDOG is not defined, the watchdog jumper on the
+/*-----------------------------------------------------------------------
+ * Watchdog Configuration
+ * NOTE: If CONFIG_HW_WATCHDOG is NOT defined, the watchdog jumper on the
* bottom (processor) board MUST be removed!
*/
#undef CONFIG_WATCHDOG
#define CONFIG_HW_WATCHDOG
- /*-----------------------------------------------------------------------
- * Serial Configuration
- */
+/*-----------------------------------------------------------------------
+ * Real Time Clock Configuration
+ */
+#define CONFIG_RTC_MC146818
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0
+
+/*-----------------------------------------------------------------------
+ * Serial Configuration
+ */
#define CONFIG_SERIAL_MULTI
-#define CONFIG_CONS_INDEX 1
+#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK 1843200
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 UART0_BASE
-#define CONFIG_SYS_NS16550_COM2 UART1_BASE
-#define CONFIG_SYS_NS16550_COM3 (0x1000 + UART0_BASE)
-#define CONFIG_SYS_NS16550_COM4 (0x1000 + UART1_BASE)
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK 1843200
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_SYS_BAUDRATE_TABLE {300, 600, 1200, 2400, 4800, \
+ 9600, 19200, 38400, 115200}
+#define CONFIG_SYS_NS16550_COM1 UART0_BASE
+#define CONFIG_SYS_NS16550_COM2 UART1_BASE
+#define CONFIG_SYS_NS16550_COM3 (0x1000 + UART0_BASE)
+#define CONFIG_SYS_NS16550_COM4 (0x1000 + UART1_BASE)
#define CONFIG_SYS_NS16550_PORT_MAPPED
- /*-----------------------------------------------------------------------
- * Video Configuration
- */
-#undef CONFIG_VIDEO /* No Video Hardware */
-#undef CONFIG_CFB_CONSOLE
-
-/*
- * Size of malloc() pool
+/*-----------------------------------------------------------------------
+ * Video Configuration
*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#undef CONFIG_VIDEO
+#undef CONFIG_CFB_CONSOLE
/*-----------------------------------------------------------------------
* Command line configuration.
*/
#include <config_cmd_default.h>
-#define CONFIG_CMD_BDI /* bdinfo */
-#define CONFIG_CMD_BOOTD /* bootd */
-#define CONFIG_CMD_CONSOLE /* coninfo */
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CONSOLE
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ECHO /* echo arguments */
-#define CONFIG_CMD_FLASH /* flinfo, erase, protect */
-#define CONFIG_CMD_FPGA /* FPGA configuration Support */
-#define CONFIG_CMD_IMI /* iminfo */
-#define CONFIG_CMD_IMLS /* List all found images */
-#define CONFIG_CMD_IRQ /* IRQ Information */
-#define CONFIG_CMD_ITEST /* Integer (and string) test */
-#define CONFIG_CMD_LOADB /* loadb */
-#define CONFIG_CMD_LOADS /* loads */
-#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
-#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/
-#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
-#undef CONFIG_CMD_NFS /* NFS support */
-#define CONFIG_CMD_PCI /* PCI support */
-#define CONFIG_CMD_PING /* ICMP echo support */
-#define CONFIG_CMD_RUN /* run command in env variable */
-#define CONFIG_CMD_SAVEENV /* saveenv */
-#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
-#define CONFIG_CMD_SOURCE /* "source" command Support */
-#define CONFIG_CMD_XIMG /* Load part of Multi Image */
-
-#define CONFIG_BOOTDELAY 15
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
-/* #define CONFIG_BOOTCOMMAND "bootm 38000000" */
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_IMLS
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ITEST
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SETGETDCR
+#define CONFIG_CMD_SOURCE
+#define CONFIG_CMD_XIMG
+
+#define CONFIG_BOOTDELAY 15
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#define CONFIG_KGDB_BAUDRATE 115200
+#define CONFIG_KGDB_SER_INDEX 2
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "boot > " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + \
- 16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "boot > "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + \
+ 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_HZ 1000 /* incrementer freq: 1kHz */
+#define CONFIG_SYS_MEMTEST_START 0x00100000
+#define CONFIG_SYS_MEMTEST_END 0x01000000
+#define CONFIG_SYS_LOAD_ADDR 0x100000
+#define CONFIG_SYS_HZ 1000
/*-----------------------------------------------------------------------
* SDRAM Configuration
*/
-#define CONFIG_SYS_SDRAM_DRCTMCTL 0x18
-#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_SYS_SDRAM_DRCTMCTL 0x18
+#define CONFIG_NR_DRAM_BANKS 4
/* CONFIG_SYS_SDRAM_DRCTMCTL Overrides the following*/
#undef CONFIG_SYS_SDRAM_PRECHARGE_DELAY
@@ -158,96 +148,78 @@
/*-----------------------------------------------------------------------
* CPU Features
*/
-#define CONFIG_SYS_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
-#define CONFIG_SYS_SC520_RESET /* use SC520 MMCR's to reset cpu */
-#define CONFIG_SYS_SC520_TIMER /* use SC520 swtimers */
-#undef CONFIG_SYS_GENERIC_TIMER /* use the i8254 PIT timers */
-#undef CONFIG_SYS_TSC_TIMER /* use the Pentium TSC timers */
-#define CONFIG_SYS_USE_SIO_UART 0 /* prefer the uarts on the SIO to those
- * in the SC520 on the CDP */
+#define CONFIG_SYS_SC520_HIGH_SPEED 0
+#define CONFIG_SYS_SC520_RESET
+#define CONFIG_SYS_SC520_TIMER
+#undef CONFIG_SYS_GENERIC_TIMER
#define CONFIG_SYS_PCAT_INTERRUPTS
-#define CONFIG_SYS_NUM_IRQS 16
+#define CONFIG_SYS_NUM_IRQS 16
/*-----------------------------------------------------------------------
- * Memory organization
+ * Memory organization:
+ * 32kB Stack
+ * 256kB Monitor
*/
-#define CONFIG_SYS_STACK_SIZE 0x8000 /* Size of bootloader stack */
-#define CONFIG_SYS_BL_START_FLASH 0x38040000 /* Address of relocated code */
-#define CONFIG_SYS_BL_START_RAM 0x03fd0000 /* Address of relocated code */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_FLASH_BASE 0x38000000 /* Boot Flash */
-#define CONFIG_SYS_FLASH_BASE_1 0x10000000 /* StrataFlash 1 */
-#define CONFIG_SYS_FLASH_BASE_2 0x11000000 /* StrataFlash 2 */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_STACK_SIZE 0x8000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
- /*-----------------------------------------------------------------------
- * FLASH configuration
- */
-#define CONFIG_FLASH_CFI_DRIVER /* Use the common driver */
+/*-----------------------------------------------------------------------
+ * FLASH configuration
+ * 512kB Boot Flash @ 0x38000000 (Monitor @ 38040000)
+ * 16MB StrataFlash #1 @ 0x10000000
+ * 16MB StrataFlash #2 @ 0x11000000
+ */
+#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_FLASH_CFI_LEGACY
-#define CONFIG_SYS_FLASH_CFI /* Flash is CFI conformant */
-#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \
- CONFIG_SYS_FLASH_BASE_1, \
- CONFIG_SYS_FLASH_BASE_2}
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_MAX_FLASH_BANKS 3
+#define CONFIG_SYS_FLASH_BASE 0x38000000
+#define CONFIG_SYS_FLASH_BASE_1 0x10000000
+#define CONFIG_SYS_FLASH_BASE_2 0x11000000
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \
+ CONFIG_SYS_FLASH_BASE_1, \
+ CONFIG_SYS_FLASH_BASE_2}
#define CONFIG_SYS_FLASH_EMPTY_INFO
#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
+#define CONFIG_SYS_MAX_FLASH_SECT 128
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
#define CONFIG_SYS_FLASH_LEGACY_512Kx8
-
- /*-----------------------------------------------------------------------
- * Environment configuration
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE_1
+#define CONFIG_SYS_FLASH_ERASE_TOUT 2000 /* ms */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 2000 /* ms */
+/*-----------------------------------------------------------------------
+ * Environment configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE_1
/* Redundant Copy */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE_1 + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SECT_SIZE
-
-
- /*-----------------------------------------------------------------------
- * PCI configuration
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_PNP /* pci plug-and-play */
-#define CONFIG_SYS_FIRST_PCI_IRQ 10
-#define CONFIG_SYS_SECOND_PCI_IRQ 9
-#define CONFIG_SYS_THIRD_PCI_IRQ 11
-#define CONFIG_SYS_FORTH_PCI_IRQ 15
-
- /*
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE_1 + \
+ CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SECT_SIZE
+
+/*-----------------------------------------------------------------------
+ * PCI configuration
+ */
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_SYS_FIRST_PCI_IRQ 10
+#define CONFIG_SYS_SECOND_PCI_IRQ 9
+#define CONFIG_SYS_THIRD_PCI_IRQ 11
+#define CONFIG_SYS_FORTH_PCI_IRQ 15
+
+/*-----------------------------------------------------------------------
* Network device (TRL8100B) support
*/
#define CONFIG_NET_MULTI
#define CONFIG_RTL8139
/*-----------------------------------------------------------------------
- * FPGA configuration
- */
-#define CONFIG_SYS_FPGA_PROGRAM_PIO_BIT 0x2000
-#define CONFIG_SYS_FPGA_INIT_PIO_BIT 0x4000
-#define CONFIG_SYS_FPGA_DONE_PIO_BIT 0x8000
-#define CONFIG_SYS_FPGA_PIO_DATA SC520_PIODATA31_16
-#define CONFIG_SYS_FPGA_PIO_DIRECTION SC520_PIODIR31_16
-#define CONFIG_SYS_FPGA_PIO_CLR SC520_PIOCLR31_16
-#define CONFIG_SYS_FPGA_PIO_SET SC520_PIOSET31_16
-#define CONFIG_SYS_FPGA_PROGRAM_BIT_DROP_TIME 1 /* milliseconds */
-#define CONFIG_SYS_FPGA_MAX_INIT_TIME 10 /* milliseconds */
-#define CONFIG_SYS_FPGA_MAX_FINALISE_TIME 10 /* milliseconds */
-#define CONFIG_SYS_FPGA_SSI_DATA_RATE 8333 /* kHz (33.3333MHz xtal) */
-
-/*-----------------------------------------------------------------------
* BOOTCS Control (for AM29LV040B-120JC)
*
* 000 0 00 0 000 11 0 011 }- 0x0033
@@ -614,17 +586,4 @@
*/
#define CONFIG_SYS_SC520_DPRAM_PAR 0x50018100
-#ifndef __ASSEMBLER__
-extern unsigned long ip;
-
-#define PRINTIP asm ("call 0\n" \
- "0:\n" \
- "pop %%eax\n" \
- "movl %%eax, %0\n" \
- :"=r"(ip) \
- : /* No Input Registers */ \
- :"%eax"); \
- printf("IP: 0x%08lx (File: %s, Line: %d)\n", ip, __FILE__, __LINE__);
-
-#endif
#endif /* __CONFIG_H */
generated by cgit v1.1 at 2024-11-10 09:36:58 +0000