summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/freescale/mpc8572ds/ddr.c122
-rw-r--r--include/configs/MPC8572DS.h3
2 files changed, 96 insertions, 29 deletions
diff --git a/board/freescale/mpc8572ds/ddr.c b/board/freescale/mpc8572ds/ddr.c
index 435893a..d66ede2 100644
--- a/board/freescale/mpc8572ds/ddr.c
+++ b/board/freescale/mpc8572ds/ddr.c
@@ -39,42 +39,108 @@ void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
}
}
+typedef struct {
+ u32 datarate_mhz_low;
+ u32 datarate_mhz_high;
+ u32 n_ranks;
+ u32 clk_adjust;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2T;
+} board_specific_parameters_t;
+
+/* ranges for parameters:
+ * wr_data_delay = 0-6
+ * clk adjust = 0-8
+ * cpo 2-0x1E (30)
+ */
+
+
+/* XXX: these values need to be checked for all interleaving modes. */
+/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
+ * seem reliable, but errors will appear when memory intensive
+ * program is run. */
+/* XXX: Single rank at 800 MHz is OK. */
+const board_specific_parameters_t board_specific_parameters[][20] = {
+ {
+ /* memory controller 0 */
+ /* lo| hi| num| clk| cpo|wrdata|2T */
+ /* mhz| mhz|ranks|adjst| | delay| */
+ { 0, 333, 2, 6, 7, 3, 0},
+ {334, 400, 2, 6, 9, 3, 0},
+ {401, 549, 2, 6, 11, 3, 0},
+ {550, 680, 2, 1, 10, 5, 0},
+ {681, 850, 2, 1, 12, 5, 1},
+ { 0, 333, 1, 6, 7, 3, 0},
+ {334, 400, 1, 6, 9, 3, 0},
+ {401, 549, 1, 6, 11, 3, 0},
+ {550, 680, 1, 1, 10, 5, 0},
+ {681, 850, 1, 1, 12, 5, 0}
+ },
+
+ {
+ /* memory controller 1 */
+ /* lo| hi| num| clk| cpo|wrdata|2T */
+ /* mhz| mhz|ranks|adjst| | delay| */
+ { 0, 333, 2, 6, 7, 3, 0},
+ {334, 400, 2, 6, 9, 3, 0},
+ {401, 549, 2, 6, 11, 3, 0},
+ {550, 680, 2, 1, 11, 6, 0},
+ {681, 850, 2, 1, 13, 6, 1},
+ { 0, 333, 1, 6, 7, 3, 0},
+ {334, 400, 1, 6, 9, 3, 0},
+ {401, 549, 1, 6, 11, 3, 0},
+ {550, 680, 1, 1, 11, 6, 0},
+ {681, 850, 1, 1, 13, 6, 0}
+ }
+};
+
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
- /*
- * Factors to consider for clock adjust:
- * - number of chips on bus
- * - position of slot
- * - DDR1 vs. DDR2?
- * - ???
- *
- * This needs to be determined on a board-by-board basis.
- * 0110 3/4 cycle late
- * 0111 7/8 cycle late
- */
- popts->clk_adjust = 7;
+ const board_specific_parameters_t *pbsp =
+ &(board_specific_parameters[ctrl_num][0]);
+ u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+ sizeof(board_specific_parameters[0][0]);
+ u32 i;
+ ulong ddr_freq;
- /*
- * Factors to consider for CPO:
- * - frequency
- * - ddr1 vs. ddr2
+ /* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+ * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+ * there are two dimms in the controller, set odt_rd_cfg to 3 and
+ * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
*/
- popts->cpo_override = 10;
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i&1) { /* odd CS */
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 0;
+ } else { /* even CS */
+ if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 4;
+ } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+ popts->cs_local_opts[i].odt_rd_cfg = 3;
+ popts->cs_local_opts[i].odt_wr_cfg = 3;
+ }
+ }
+ }
- /*
- * Factors to consider for write data delay:
- * - number of DIMMs
- *
- * 1 = 1/4 clock delay
- * 2 = 1/2 clock delay
- * 3 = 3/4 clock delay
- * 4 = 1 clock delay
- * 5 = 5/4 clock delay
- * 6 = 3/2 clock delay
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
*/
- popts->write_data_delay = 5;
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ for (i = 0; i < num_params; i++) {
+ if (ddr_freq >= pbsp->datarate_mhz_low &&
+ ddr_freq <= pbsp->datarate_mhz_high &&
+ pdimm->n_ranks == pbsp->n_ranks) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay = pbsp->write_data_delay;
+ popts->twoT_en = pbsp->force_2T;
+ }
+ pbsp++;
+ }
/*
* Factors to consider for half-strength driver enable:
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index c2ed961..c2606fa 100644
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -61,7 +61,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
-#define CONFIG_ICS307_REFCLK_HZ 33333333 /* ICS307 clock chip ref freq */
+#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
#define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq
from ICS307 instead of switches */
@@ -549,6 +549,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "memctl_intlv_ctl=2\0" \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \