diff options
| -rw-r--r-- | CHANGELOG | 248 | ||||
| -rw-r--r-- | Makefile | 18 | ||||
| -rw-r--r-- | drivers/ne2000.c | 10 |
3 files changed, 259 insertions, 17 deletions
@@ -1,3 +1,206 @@ +commit ff285ca07eda1ea4a8909848cc1cc604ec8fec9c +Author: Vlad Lungu <vlad@comsys.ro> +Date: Thu Oct 4 20:47:10 2007 +0300 + + Fix NE2000 driver: + + Fixed typo in ne2000.h, thinko re n2k_inb() usage, don't try + to do anything in eth_stop() if eth_init() was not called. + Simplified RX path in order to avoid timeouts on really really + fast NE2000 cards (read: qemu with internal tftp), NetLoop() is + clever enough to cope with 1 packet per eth_rx(). + + Signed-off-by: Vlad Lungu <vlad@comsys.ro> + +commit 5441f61a3d8b7034f19fc1361183e936198e6dbb +Author: Detlev Zundel <dzu@denx.de> +Date: Fri Oct 19 16:47:26 2007 +0200 + + Fix two typos. + + Signed-off-by: Detlev Zundel <dzu@denx.de> + +commit 281df457c1aa50d2752165d0c5c3282d4027b974 +Author: Tony Li <tony.li@freescale.com> +Date: Thu Oct 18 17:47:19 2007 +0800 + + mpc83xx: Add configure entry for MPC83xx ATM support + + Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into + Makfile and MAKEALL + + Signed-off-by: Tony Li <tony.li@freescale.com> + Signed-off-by: Kim Phillips <kim.phillips@freescale.com> + +commit d2646554f529a9577515eceb0ec5eceee18244ba +Author: Tony Li <tony.li@freescale.com> +Date: Thu Oct 18 17:44:38 2007 +0800 + + mpc83xx: pq-mds-pib.c typo error + + Correct to val8 from val. + + Signed-off-by: Tony Li <tony.li@freescale.com> + Signed-off-by: Kim Phillips <kim.phillips@freescale.com> + +commit 3e11ae80fec1ee12194940955431186abf6009c2 +Author: Stefan Roese <sr@denx.de> +Date: Wed Oct 17 15:40:19 2007 +0200 + + ppc4xx: Add 667/133 (CPU/PLB) frequency setup to Sequoia bootstrap command + + Signed-off-by: Stefan Roese <sr@denx.de> + +commit 7ee6ba1a056e4061ab4cfde30127e332e7957afd +Author: runet@innovsys.com <runet@innovsys.com> +Date: Tue Oct 16 14:50:40 2007 -0500 + + Make MPC8266ADS board compile again. + + Signed-off-by: Runet Torgersen <runet@innovsys.com> + +commit 2491167c245d8ebe6f2dbd8c4287aaa0d14fe93a +Author: Jon Loeliger <jdl@freescale.com> +Date: Mon Aug 27 12:41:03 2007 -0500 + + 86xx: Allow for fewer DDR slots per memory controller. + + As a direct correlation exists between DDR DIMM slots + and SPD EEPROM addresses used to configure them, use + the individually defined SPD_EEPROM_ADDRESS* values to + determine if a DDR DIMM slot should have its SPD + configuration read or not. + + Effectively, this now allows for 1 or 2 DIMM slots + per memory controller. + + Signed-off-by: Jon Loeliger <jdl@freescale.com> + +commit 4d4a945e189a2f384c66432316da2788a0ac1607 +Author: Rodolfo Giometti <giometti@enneenne.com> +Date: Mon Oct 15 11:59:17 2007 +0200 + + PXA USB OHCI: "usb stop" implementation. + + Some USB keys need to be switched off before loading the kernel + otherwise they can remain in an undefined status which prevents them + to be correctly recognized by the kernel. + + Signed-off-by: Rodolfo Giometti <giometti@linux.it> + +commit e2e93442e558cf1500e92861f99713b2f045ea22 +Author: Stefan Roese <sr@denx.de> +Date: Mon Oct 15 11:39:00 2007 +0200 + + ppc4xx: Fix bug in I2C bootstrap values for Sequoia/Rainier + + The I2C bootstrap values that can be setup via the "bootstrap" command, + were setup incorrect regarding the generation of the internal sync PCI + clock. The values for PLB clock == 133MHz were slighly incorrect and the + values for PLB clock == 166MHz were totally incorrect. This could + lead to a hangup upon booting while PCI configuration scan. + + This patch fixes this issue and configures valid PCI divisor values + for the sync PCI clock, with respect to the provided external async + PCI frequency. + + Here the values of the formula in the chapter 14.2 "PCI clocking" + from the 440EPx users manual: + + AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz + + 33MHz async PCI frequency: + PLB = 133: + => 32 <= 44.3 <= 65 (div = 3) + + PLB = 166: + => 32 <= 55.3 <= 65 (div = 3) + + 66MHz async PCI frequency: + PLB = 133: + => 65 <= 66.5 <= 132 (div = 2) + + PLB = 166: + => 65 <= 83 <= 132 (div = 2) + + Signed-off-by: Stefan Roese <sr@denx.de> + +commit 5a5958b7de70ae99f0e7cbd5c97ec1346e051587 +Author: Stefan Roese <sr@denx.de> +Date: Mon Oct 15 11:29:33 2007 +0200 + + ppc4xx: Fix incorrect 33/66MHz PCI clock log-message on Sequoia & Yosemite + + The BCSR status bit for the 66MHz PCI operation was correctly + addressed (MSB/LSB problem). Now the correct currently setup + PCI frequency is displayed upon bootup. + + This patch also fixes this problem on Rainier & Yellowstone, since these + boards use the same souce code as Sequoia & Yosemite do. + + Signed-off-by: Stefan Roese <sr@denx.de> + +commit da3aad55cbde80ab6e301aafa82a2c411aa53eff +Author: Martin Krause <martin.krause@tqs.de> +Date: Wed Sep 26 17:55:56 2007 +0200 + + TQM860M: adjust for doubled flash sector size. + + Adjust flash map to support the new S29GLxxN (N-Type) Flashes with + doubled sector size. + + Signed-off-by: Martin Krause <martin.krause@tqs.de> + +commit 9d29250e2e62f4bf20c7a20b4173d84c48f11f5d +Author: Jens Gehrlein <jens.gehrlein@tqs.de> +Date: Wed Sep 26 17:55:54 2007 +0200 + + TQM8xx: Fix CAN timing. + + Signed-off-by: Martin Krause <martin.krause@tqs.de> + +commit d43e489baf02afae49077791fb22332d240d8656 +Author: Martin Krause <martin.krause@tqs.de> +Date: Thu Sep 27 14:54:36 2007 +0200 + + TQM866M: fix SDRAM refresh + + At 133 MHz the current SDRAM refresh rate is too fast + (measured 4 * 1.17 us). + CFG_MAMR_PTA changes from 39 to 97. This result + in a refresh rate of 4 * 7.8 us at the default clock + 50 MHz. At 133 MHz the value will be then 4 * 2.9 us. + This is a compromise until a new method is found to + adjust the refresh rate. + + Signed-off-by: Martin Krause <martin.krause@tqs.de> + +commit 9ef57bbee1c67cc01da2026c242c4692db32be36 +Author: Martin Krause <martin.krause@tqs.de> +Date: Wed Sep 26 17:55:55 2007 +0200 + + TQM866M: adjust for doubled flash sector size. + + Adjust flash map to support the new S29GLxxN (N-Type) Flashes with + doubled sector size. + + Signed-off-by: Martin Krause <martin.krause@tqs.de> + +commit f8bf90461d9bad2e6fed31fcebaf235f60dd6763 +Author: Michal Simek <monstr@monstr.eu> +Date: Sun Oct 14 16:12:29 2007 +0200 + + [FIX] XUPV2P change command handling + and remove code violation + +commit 636400198228d96983c06657b17f760f5989958e +Author: Wolfgang Denk <wd@denx.de> +Date: Sun Oct 14 00:13:19 2007 +0200 + + Prepare for 1.3.0-rc3 release + + Signed-off-by: Wolfgang Denk <wd@denx.de> + commit 68f14f77ca5fe5f9cc025c8cae101671f628309f Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Date: Sat Sep 29 13:41:37 2007 +0200 @@ -109,6 +312,26 @@ Date: Mon Oct 1 09:51:50 2007 +0200 Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com> +commit 785c13477b77dcd2e6c5128fffcdb4e1943f4818 +Author: Timo Ketola <timo.ketola@exertus.fi> +Date: Mon Sep 24 14:50:32 2007 +0300 + + Bugfix: Use only one PTD for one endpoint + + Original isp116x-hcd code prepared multiple PTDs for longer than 16 + byte transfers for one endpoint. That is unnecessary because the + ISP116x is able to split long data from one PTD into multiple + transactions based on the buffer size of the endpoint. It also caused + serious problems if the endpoint NAKed some of the transactions. In + that case ISP116x wouldn't notice that the other PTDs were for the same + endpoint and would try the other PTDs possibly out of order. That would + break the whole transfer. + + This patch makes isp116x_submit_job to use one PTD for one transfer. + + Signed-off-by: Timo Ketola <timo.ketola@exertus.fi> + Signed-off-by: Markus Klotzbuecher <mk@denx.de> + commit 86ec86c04326c3913178a7679aa910de071da75d Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Date: Thu Sep 27 23:27:47 2007 +0200 @@ -331,6 +554,12 @@ Date: Mon Sep 10 17:13:49 2007 +0900 Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> +commit b49c90df6e7cfcfb8b862b8bbf8448dff5eed9a5 +Author: Michal Simek <monstr@monstr.eu> +Date: Sun Sep 16 20:51:57 2007 +0200 + + [FIX] remove files form repository + commit 67c31036acaaaa992fc346cc89db0909a7e733c4 Author: Wolfgang Denk <wd@denx.de> Date: Sun Sep 16 17:10:04 2007 +0200 @@ -478,6 +707,25 @@ Date: Sat Sep 15 11:55:42 2007 +0200 [1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/31805 +commit 991b089d1ce5ad945725e3657a8f106dfa02a38e +Author: Michal Simek <monstr@monstr.eu> +Date: Sat Sep 15 00:03:35 2007 +0200 + + Synchronize with U-BOOT mainline + +commit d7fee32b7e61fe11c64e371cde79faa4768e8350 +Author: Sam Sparks <SSparks@twacs.com> +Date: Fri Sep 14 11:14:42 2007 -0600 + + Update MPC8349ITX*_config to place config.tmp in right place. + + MPC834ITX*_config does not store config.tmp at the correct locatation, + causing MPC8349ITXGP to have the wrong TEXT_BASE. + + Signed-off-by: Sam Sparks <SSparks@twacs.com> + Signed-off-by: Grant Likely <grant.likely@secretlab.ca> + Signed-off-by: Kim Phillips <kim.phillips@freescale.com> + commit 6e7b7b6ea1b6d04dbe96242eb6a0c1c664c98e8c Author: Bartlomiej Sieka <tur@semihalf.com> Date: Thu Sep 13 18:21:48 2007 +0200 @@ -393,7 +393,7 @@ BC3450_config: unconfig cpci5200_config: unconfig @$(MKCONFIG) -a cpci5200 ppc mpc5xxx cpci5200 esd -hmi1001_config: unconfig +hmi1001_config: unconfig @$(MKCONFIG) hmi1001 ppc mpc5xxx hmi1001 Lite5200_config \ @@ -435,7 +435,7 @@ icecube_5100_config: unconfig } @$(MKCONFIG) -a IceCube ppc mpc5xxx icecube -jupiter_config: unconfig +jupiter_config: unconfig @$(MKCONFIG) jupiter ppc mpc5xxx jupiter v38b_config: unconfig @@ -640,9 +640,9 @@ TQM5200_STK100_config: unconfig { echo "TEXT_BASE = 0xFFF00000" >$(obj)board/tqm5200/config.tmp ; \ } @$(MKCONFIG) -n $@ -a TQM5200 ppc mpc5xxx tqm5200 -uc101_config: unconfig +uc101_config: unconfig @$(MKCONFIG) uc101 ppc mpc5xxx uc101 -motionpro_config: unconfig +motionpro_config: unconfig @$(MKCONFIG) motionpro ppc mpc5xxx motionpro @@ -930,7 +930,7 @@ RPXlite_DW_NVRAM_config \ RPXlite_DW_NVRAM_64_config \ RPXlite_DW_NVRAM_LCD_config \ RPXlite_DW_NVRAM_64_LCD_config \ -RPXlite_DW_config: unconfig +RPXlite_DW_config: unconfig @mkdir -p $(obj)include @ >$(obj)include/config.h @[ -z "$(findstring _64,$@)" ] || \ @@ -1793,7 +1793,7 @@ MPC832XEMDS_ATM_config: unconfig echo -n "...ATM..." ; \ echo "#define CONFIG_PQ_MDS_PIB 1" >>$(obj)include/config.h ; \ echo "#define CONFIG_PQ_MDS_PIB_ATM 1" >>$(obj)include/config.h ; \ - fi ; + fi ; @$(MKCONFIG) -a MPC832XEMDS ppc mpc83xx mpc832xemds freescale MPC8349EMDS_config: unconfig @@ -2001,13 +2001,13 @@ AmigaOneG3SE_config: unconfig BAB7xx_config: unconfig @$(MKCONFIG) $(@:_config=) ppc 74xx_7xx bab7xx eltec -CPCI750_config: unconfig +CPCI750_config: unconfig @$(MKCONFIG) CPCI750 ppc 74xx_7xx cpci750 esd -DB64360_config: unconfig +DB64360_config: unconfig @$(MKCONFIG) DB64360 ppc 74xx_7xx db64360 Marvell -DB64460_config: unconfig +DB64460_config: unconfig @$(MKCONFIG) DB64460 ppc 74xx_7xx db64460 Marvell ELPPC_config: unconfig diff --git a/drivers/ne2000.c b/drivers/ne2000.c index 0bfe74e..695a1dc 100644 --- a/drivers/ne2000.c +++ b/drivers/ne2000.c @@ -745,14 +745,12 @@ static void pcnet_reset_8390(void) PRINTK("nic base is %lx\n", nic_base); -#if 1 n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD); PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); PRINTK("cmd (at %lx) is %x\n", nic_base+ E8390_CMD, n2k_inb(E8390_CMD)); -#endif n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD); n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET); @@ -847,12 +845,9 @@ void uboot_push_packet_len(int len) { } plen[nrx] = len; dp83902a_recv(&pbuf[nrx*2000], len); -/*Just pass it to the upper layer*/ + + /*Just pass it to the upper layer*/ NetReceive(&pbuf[nrx*2000], plen[nrx]); -/*eth_rx() was gutted, so this is not needed anymore*/ -#if 0 - nrx++; -#endif } void uboot_push_tx_done(int key, int val) { @@ -949,5 +944,4 @@ int eth_send(volatile void *packet, int length) { } return 0; } - #endif |