powerpc/85xx: Add support for new P102x/P2020 RDB style boards

The following boards share a common design but with minor variations
between them:

P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC

The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.

Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots

As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.

CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.

VSC firmware Address is defined by default in config file for eTSEC1.

SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.

Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below

'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>

2 files changed, 271 insertions, 0 deletions

diff --git a/nand_spl/board/freescale/p1_p2_rdb_pc/Makefile b/nand_spl/board/freescale/p1_p2_rdb_pc/Makefile
new file mode 100644
index 0000000..475cc49
--- /dev/null
+++ b/nand_spl/board/freescale/p1_p2_rdb_pc/Makefile
@@ -0,0 +1,137 @@
+#
+# (C) Copyright 2007
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# Copyright 2011 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+NAND_SPL := y
+CONFIG_SYS_TEXT_BASE_SPL := 0xfff00000
+PAD_TO := 0xff801000
+
+include $(TOPDIR)/config.mk
+
+nandobj	:= $(OBJTREE)/nand_spl/
+
+LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-nand_spl.lds
+LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \
+		$(LDFLAGS) $(LDFLAGS_FINAL)
+AFLAGS	+= -DCONFIG_NAND_SPL
+CFLAGS	+= -DCONFIG_NAND_SPL
+
+SOBJS	= start.o resetvec.o
+COBJS	= cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \
+	  nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(nandobj)board/$(BOARDDIR)
+
+ALL	= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all:	$(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl:	$(OBJS) $(nandobj)u-boot-nand_spl.lds
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \
+		-Map $(nandobj)u-boot-spl.map \
+		-o $(nandobj)u-boot-spl
+
+$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT)
+	$(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links for common files
+
+$(obj)cache.c:
+	@rm -f $(obj)cache.c
+	ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c
+
+$(obj)cpu_init_early.c:
+	@rm -f $(obj)cpu_init_early.c
+	ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_early.c $(obj)cpu_init_early.c
+
+$(obj)cpu_init_nand.c:
+	@rm -f $(obj)cpu_init_nand.c
+	ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_nand.c $(obj)cpu_init_nand.c
+
+$(obj)fsl_law.c:
+	@rm -f $(obj)fsl_law.c
+	ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c
+
+$(obj)law.c:
+	@rm -f $(obj)law.c
+	ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c
+
+$(obj)nand_boot_fsl_elbc.c:
+	@rm -f $(obj)nand_boot_fsl_elbc.c
+	ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \
+	       $(obj)nand_boot_fsl_elbc.c
+
+$(obj)ns16550.c:
+	@rm -f $(obj)ns16550.c
+	ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c
+
+$(obj)resetvec.S:
+	@rm -f $(obj)resetvec.S
+	ln -s $(SRCTREE)/$(CPUDIR)/resetvec.S $(obj)resetvec.S
+
+$(obj)fixed_ivor.S:
+	@rm -f $(obj)fixed_ivor.S
+	ln -sf $(SRCTREE)/$(CPUDIR)/fixed_ivor.S $(obj)fixed_ivor.S
+
+$(obj)start.S: $(obj)fixed_ivor.S
+	@rm -f $(obj)start.S
+	ln -sf $(SRCTREE)/$(CPUDIR)/start.S $(obj)start.S
+
+$(obj)tlb.c:
+	@rm -f $(obj)tlb.c
+	ln -sf $(SRCTREE)/$(CPUDIR)/tlb.c $(obj)tlb.c
+
+$(obj)tlb_table.c:
+	@rm -f $(obj)tlb_table.c
+	ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c
+
+ifneq ($(OBJTREE), $(SRCTREE))
+$(obj)nand_boot.c:
+	@rm -f $(obj)nand_boot.c
+	ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c
+endif
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c b/nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c
new file mode 100644
index 0000000..b9796ea
--- /dev/null
+++ b/nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+
+#define udelay(x) {int i, j; \
+			for (i = 0; i < x; i++) \
+				for (j = 0; j < 10000; j++) \
+					; }
+
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+void sdram_init(void)
+{
+	ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
+
+	out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
+	out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
+#if CONFIG_CHIP_SELECTS_PER_CTRL > 1
+	out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
+	out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
+#endif
+	out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+	out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+	out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+	out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+
+	out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL_2);
+	out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
+	out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
+
+	out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+	out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
+	out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
+
+	out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
+	out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
+	out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CONTROL);
+	out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CONTROL);
+
+	/* Set, but do not enable the memory */
+	out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN);
+
+	asm volatile("sync;isync");
+	udelay(500);
+
+	/* Let the controller go */
+	out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN);
+
+	set_next_law(0, CONFIG_SYS_SDRAM_SIZE_LAW, LAW_TRGT_IF_DDR_1);
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, bus_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#ifndef CONFIG_QE
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+#endif
+
+	/* initialize selected port with appropriate baud rate */
+	plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+	plat_ratio >>= 1;
+	bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+			bus_clk / 16 / CONFIG_BAUDRATE);
+
+	puts("\nNAND boot... ");
+
+#ifndef CONFIG_QE
+	/* init DDR3 reset signal */
+	out_be32(&pgpio->gpdir, 0x02000000);
+	out_be32(&pgpio->gpodr, 0x00200000);
+	out_be32(&pgpio->gpdat, 0x00000000);
+	udelay(1000);
+	out_be32(&pgpio->gpdat, 0x00200000);
+	udelay(1000);
+	out_be32(&pgpio->gpdir, 0x00000000);
+#endif
+
+	/* Initialize the DDR3 */
+	sdram_init();
+
+	/* copy code to RAM and jump to it - this should not return */
+	/* NOTE - code has to be copied out of NAND buffer before
+	 * other blocks can be read.
+	 */
+	relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0,
+			CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (c == '\n')
+		NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+	NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+	while (*str)
+		putc(*str++);
+}