powerpc/85xx: Add basic support for P1010RDB

Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.

P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
	32Mbyte 16bit NOR flash
	32Mbyte SLC NAND Flash
	64KB CPLD device(GPCM interface)
SPI Flash:
	128 Mbit SPI Flash memory
SD/MMC:
	connector to interface with the SD memory card
SATA:
	1 internal SATA connect to 2.5. 160G SATA2 HDD
	1 eSATA connector to rear panel
USB 2.0:
	x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
	x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
	eTSEC1: Connected to RGMII PHY VSC8641XKO
	eTSEC2: Connected to SGMII PHY VSC8221
	eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
	Two DB-9 female connectors for Field bus interface
UART:
	supports two UARTs up to 115200 bps for console
TDM:
	2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
	SPI SLIC
I2C:
	Serial EEprom
	Real time clock
	256 Kbit M24256 I2C EEPROM
PCIe:
	PCIe and mPCIe connectors.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

1 files changed, 706 insertions, 0 deletions

diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
new file mode 100644
index 0000000..3304ea3
--- /dev/null
+++ b/include/configs/P1010RDB.h
@@ -0,0 +1,706 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * P010 RDB board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#ifdef CONFIG_36BIT
+#define CONFIG_PHYS_64BIT
+#endif
+
+#ifdef CONFIG_P1010RDB
+#define CONFIG_P1010
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RAMBOOT_SDCARD
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x1107fffc
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE		0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE			/* BOOKE */
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_MPC85xx
+#define CONFIG_FSL_IFC			/* Enable IFC Support */
+#define CONFIG_SYS_HAS_SERDES		/* common SERDES init code */
+
+#define CONFIG_PCI			/* Enable PCI/PCIE */
+#if defined(CONFIG_PCI)
+#define CONFIG_PCIE1			/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2			/* PCIE controler 2 (slot 2) */
+#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET		/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+
+#define CONFIG_E1000			/*  E1000 pci Ethernet card*/
+
+/*
+ * PCI Windows
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME		"mini PCIe Slot"
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xfffc00000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc00000
+#endif
+
+/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME		"PCIe Slot"
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xfffc10000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
+#endif
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+#define CONFIG_TSEC_ENET
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_DDR_CLK_FREQ	66666666 /* DDRCLK on P1010 RDB */
+#define CONFIG_SYS_CLK_FREQ	66666666 /* SYSCLK for P1010 RDB */
+
+#ifndef CONFIG_SDCARD
+#define CONFIG_MISC_INIT_R
+#endif
+
+#define CONFIG_HWCONFIG
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP			1
+#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x1fffffff
+#define CONFIG_PANIC_HANG		/* do not reset board on panic */
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+#define CONFIG_DDR_RAW_TIMING
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_SPD_BUS_NUM		1
+#define SPD_EEPROM_ADDRESS		0x52
+
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_sdram_size(void);
+#endif
+#define CONFIG_SYS_SDRAM_SIZE		get_sdram_size() /* DDR size */
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	1
+
+/* DDR3 Controller Settings */
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000003f
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014302
+#define CONFIG_SYS_DDR_CS0_CONFIG_2	0x00000000
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_INIT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_INIT_EXT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_MODE_CONTROL	0x00000000
+
+#define CONFIG_SYS_DDR_ZQ_CONTROL	0x89080600
+#define CONFIG_SYS_DDR_SR_CNTR		0x00000000
+#define CONFIG_SYS_DDR_RCW_1		0x00000000
+#define CONFIG_SYS_DDR_RCW_2		0x00000000
+#define CONFIG_SYS_DDR_CONTROL		0x470C0000	/* Type = DDR3  */
+#define CONFIG_SYS_DDR_CONTROL_2	0x04401010
+#define CONFIG_SYS_DDR_TIMING_4		0x00000001
+#define CONFIG_SYS_DDR_TIMING_5		0x03402400
+
+#define CONFIG_SYS_DDR_TIMING_3_800	0x00020000
+#define CONFIG_SYS_DDR_TIMING_0_800	0x00330004
+#define CONFIG_SYS_DDR_TIMING_1_800	0x6f6B4644
+#define CONFIG_SYS_DDR_TIMING_2_800	0x0FA888CF
+#define CONFIG_SYS_DDR_CLK_CTRL_800	0x03000000
+#define CONFIG_SYS_DDR_MODE_1_800	0x40461520
+#define CONFIG_SYS_DDR_MODE_2_800	0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL_800	0x0C300100
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_800	0x8655A608
+
+/* settings for DDR3 at 667MT/s */
+#define CONFIG_SYS_DDR_TIMING_3_667		0x00010000
+#define CONFIG_SYS_DDR_TIMING_0_667		0x00110004
+#define CONFIG_SYS_DDR_TIMING_1_667		0x5d59e544
+#define CONFIG_SYS_DDR_TIMING_2_667		0x0FA890CD
+#define CONFIG_SYS_DDR_CLK_CTRL_667		0x03000000
+#define CONFIG_SYS_DDR_MODE_1_667		0x00441210
+#define CONFIG_SYS_DDR_MODE_2_667		0x00000000
+#define CONFIG_SYS_DDR_INTERVAL_667		0x0a280000
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_667	0x8675F608
+
+#define CONFIG_SYS_CCSRBAR			0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW		CONFIG_SYS_CCSRBAR
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000	0x3fff_ffff	DDR			1G cacheable
+ * 0x8000_0000  0xbfff_ffff	PCI Express Mem		1.5G non-cacheable
+ * 0xffc0_0000  0xffc3_ffff	PCI IO range		256k non-cacheable
+ *
+ * Localbus non-cacheable
+ * 0xff80_0000	0xff8f_ffff	NAND Flash		1M non-cacheable
+ * 0xffb0_0000	0xffbf_ffff	Board CPLD		1M non-cacheable
+ * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
+ * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
+ */
+
+/* In case of SD card boot, IFC interface is not available because of muxing */
+#ifdef CONFIG_SDCARD
+#define CONFIG_SYS_NO_FLASH
+#else
+/*
+ * IFC Definitions
+ */
+/* NOR Flash on IFC */
+#define CONFIG_SYS_FLASH_BASE		0xee000000
+#define CONFIG_SYS_MAX_FLASH_SECT	256	/* 32M */
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_NOR_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(32*1024*1024)
+#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(7)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_FTIM0	FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5)
+#define CONFIG_SYS_NOR_FTIM1	FTIM1_NOR_TACO(0x1e) | \
+				FTIM1_NOR_TRAD_NOR(0x0f)
+#define CONFIG_SYS_NOR_FTIM2	FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWP(0x1c)
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+/* CFI for NOR Flash */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+/* NAND Flash on IFC */
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS	0xfff800000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8	\
+				| CSPR_MSEL_NAND	\
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
+				| CSOR_NAND_RAL_2	/* RAL = 2 Bytes */ \
+				| CSOR_NAND_PGS_512	/* Page Size = 512b */ \
+				| CSOR_NAND_SPRZ_16	/* Spare size = 16 */ \
+				| CSOR_NAND_PB(32))	/* 32 Pages Per Block */
+
+/* NAND Flash Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		FTIM0_NAND_TCCST(0x01) | \
+					FTIM0_NAND_TWP(0x0C)   | \
+					FTIM0_NAND_TWCHT(0x04) | \
+					FTIM0_NAND_TWH(0x05)
+#define CONFIG_SYS_NAND_FTIM1		FTIM1_NAND_TADLE(0x1d) | \
+					FTIM1_NAND_TWBE(0x1d)  | \
+					FTIM1_NAND_TRR(0x07)   | \
+					FTIM1_NAND_TRP(0x0c)
+#define CONFIG_SYS_NAND_FTIM2		FTIM2_NAND_TRAD(0x0c) | \
+					FTIM2_NAND_TREH(0x05) | \
+					FTIM2_NAND_TWHRE(0x0f)
+#define CONFIG_SYS_NAND_FTIM3		FTIM3_NAND_TWW(0x04)
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+
+/* Set up IFC registers for boot location NOR/NAND */
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE		0xffb00000
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CPLD_BASE_PHYS	0xfffb00000ull
+#else
+#define CONFIG_SYS_CPLD_BASE_PHYS	CONFIG_SYS_CPLD_BASE
+#endif
+
+#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK3		IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR3		0x0
+/* CPLD Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
+					FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3		0x0
+#endif	/* CONFIG_SDCARD */
+
+#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) || \
+    defined(CONFIG_RAMBOOT_NAND)
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F	/* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000 /* stack in RAM */
+#define CONFIG_SYS_INIT_RAM_END		0x00004000 /* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END \
+						- GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon*/
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc*/
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX	1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+#define CONFIG_FSL_I2C			/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C			/* I2C with hardware support */
+#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED		400000 /* I2C speed and slave address*/
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+
+/* I2C EEPROM */
+#undef CONFIG_ID_EEPROM
+/* enable read and write access to EEPROM */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/* RTC */
+#define CONFIG_RTC_PT7C4338
+#define CONFIG_SYS_I2C_RTC_ADDR	0x68
+
+#define CONFIG_CMD_I2C
+
+/*
+ * SPI interface will not be available in case of NAND boot SPI CS0 will be
+ * used for SLIC
+ */
+/* eSPI - Enhanced SPI */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED		10000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+
+#if defined(CONFIG_TSEC_ENET)
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+#define CONFIG_MII			/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_TSEC1	1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define CONFIG_TSEC2	1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+#define CONFIG_TSEC3	1
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+
+#define TSEC1_PHY_ADDR		1
+#define TSEC2_PHY_ADDR		0
+#define TSEC3_PHY_ADDR		2
+
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC3_PHYIDX		0
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+
+/* TBI PHY configuration for SGMII mode */
+#define CONFIG_TSEC_TBICR_SETTINGS ( \
+		TBICR_PHY_RESET \
+		| TBICR_ANEG_ENABLE \
+		| TBICR_FULL_DUPLEX \
+		| TBICR_SPEED1_SET \
+		)
+
+#endif	/* CONFIG_TSEC_ENET */
+
+
+/* SATA */
+#define CONFIG_FSL_SATA
+#define CONFIG_LIBATA
+
+#ifdef CONFIG_FSL_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
+
+#define CONFIG_CMD_SATA
+#define CONFIG_LBA48
+#endif /* #ifdef CONFIG_FSL_SATA  */
+
+/*  SD interface will only be available in case of SD boot */
+#ifdef CONFIG_SDCARD
+#define CONFIG_MMC
+#define CONFIG_DEF_HWCONFIG		esdhc
+#endif
+
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FSL_ESDHC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#endif
+
+#define CONFIG_HAS_FSL_DR_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB)
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#endif
+#endif
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_SDCARD)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SIZE			0x2000
+#elif defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS	0
+#define CONFIG_ENV_SPI_CS	0
+#define CONFIG_ENV_SPI_MAX_HZ	10000000
+#define CONFIG_ENV_SPI_MODE	0
+#define CONFIG_ENV_OFFSET	0x100000	/* 1MB */
+#define CONFIG_ENV_SECT_SIZE	0x10000
+#define CONFIG_ENV_SIZE		0x2000
+#else
+#define CONFIG_ENV_IS_NOWHERE		/* Store ENV in memory only */
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE			0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR	0xfff80000
+#else
+#define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
+		 || defined(CONFIG_FSL_SATA)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+						/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* dec freq: 1ms ticks */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20) /* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#endif
+
+#define CONFIG_HOSTNAME		P1010RDB
+#define CONFIG_ROOTPATH		/opt/nfsroot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	u-boot.bin/* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE		115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=" MK_STR(CONFIG_DEF_HWCONFIG)  "\0"	\
+	"netdev=eth0\0"						\
+	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+	"loadaddr=1000000\0"			\
+	"consoledev=ttyS0\0"				\
+	"ramdiskaddr=2000000\0"			\
+	"ramdiskfile=rootfs.ext2.gz.uboot\0"		\
+	"fdtaddr=c00000\0"				\
+	"fdtfile=p1010rdb.dtb\0"		\
+	"bdev=sda1\0"	\
+	"hwconfig=usb1:dr_mode=host,phy_type=utmi\0"	\
+	"othbootargs=ramdisk_size=600000\0" \
+	"usbfatboot=setenv bootargs root=/dev/ram rw "	\
+	"console=$consoledev,$baudrate $othbootargs; "	\
+	"usb start;"			\
+	"fatload usb 0:2 $loadaddr $bootfile;"		\
+	"fatload usb 0:2 $fdtaddr $fdtfile;"	\
+	"fatload usb 0:2 $ramdiskaddr $ramdiskfile;"	\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr\0"		\
+	"usbext2boot=setenv bootargs root=/dev/ram rw "	\
+	"console=$consoledev,$baudrate $othbootargs; "	\
+	"usb start;"			\
+	"ext2load usb 0:4 $loadaddr $bootfile;"		\
+	"ext2load usb 0:4 $fdtaddr $fdtfile;"	\
+	"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"	\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr\0"		\
+
+#define CONFIG_RAMBOOTCOMMAND		\
+	"setenv bootargs root=/dev/ram rw "	\
+	"console=$consoledev,$baudrate $othbootargs; "	\
+	"tftp $ramdiskaddr $ramdiskfile;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#endif	/* __CONFIG_H */