Merge branch 'master' of git://git.denx.de/u-boot-arm

10 files changed, 874 insertions, 51 deletions

diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h
index e0a3bae..7bf6336 100644
--- a/include/configs/da850evm.h
+++ b/include/configs/da850evm.h
@@ -26,6 +26,7 @@
 /*
  * Board
  */
+#define CONFIG_DRIVER_TI_EMAC
 
 /*
  * SoC Configuration
@@ -79,6 +80,43 @@
 #define CONFIG_SYS_I2C_SLAVE		10 /* Bogus, master-only in U-Boot */
 
 /*
+ * Flash & Environment
+ */
+#ifdef CONFIG_USE_NAND
+#undef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_IN_NAND		/* U-Boot env in NAND Flash  */
+#define CONFIG_ENV_OFFSET		0x0 /* Block 0--not used by bootcode */
+#define CONFIG_ENV_SIZE			(128 << 10)
+#define	CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+#define	CONFIG_SYS_NAND_PAGE_2K
+#define CONFIG_SYS_NAND_CS		3
+#define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
+#define CONFIG_SYS_CLE_MASK		0x10
+#define CONFIG_SYS_ALE_MASK		0x8
+#undef CONFIG_SYS_NAND_HW_ECC
+#define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
+#define NAND_MAX_CHIPS			1
+#define DEF_BOOTM			""
+#endif
+
+/*
+ * Network & Ethernet Configuration
+ */
+#ifdef CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM	0
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT	10
+#define CONFIG_NET_MULTI
+#endif
+
+/*
  * U-Boot general configuration
  */
 #define CONFIG_BOOTFILE		"uImage" /* Boot file name */
@@ -100,7 +138,7 @@
 /*
  * Linux Information
  */
-#define LINUX_BOOT_PARAM_ADDR	(CONFIG_SYS_MEMTEST_START + 0x100)
+#define LINUX_BOOT_PARAM_ADDR	(PHYS_SDRAM_1 + 0x100)
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_BOOTARGS		\
@@ -127,6 +165,20 @@
 #undef CONFIG_CMD_PING
 #endif
 
+#ifdef CONFIG_USE_NAND
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_NAND
+
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_LZO
+#define CONFIG_RBTREE
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#endif
+
 #if !defined(CONFIG_USE_NAND) && \
 	!defined(CONFIG_USE_NOR) && \
 	!defined(CONFIG_USE_SPIFLASH)
diff --git a/include/configs/igep0020.h b/include/configs/igep0020.h
new file mode 100644
index 0000000..34e8a57
--- /dev/null
+++ b/include/configs/igep0020.h
@@ -0,0 +1,228 @@
+/*
+ * (C) Copyright 2010
+ * ISEE 2007 SL, <www.iseebcn.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMV7		1	/* This is an ARM V7 CPU core */
+#define CONFIG_OMAP		1	/* in a TI OMAP core */
+#define CONFIG_OMAP34XX		1	/* which is a 34XX */
+#define CONFIG_OMAP3430		1	/* which is in a 3430 */
+#define CONFIG_OMAP3_IGEP0020	1	/* working with IGEP0020 */
+
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
+#include <asm/arch/cpu.h>
+#include <asm/arch/omap3.h>
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO		1
+#define CONFIG_DISPLAY_BOARDINFO	1
+
+/* Clock Defines */
+#define V_OSCK			26000000	/* Clock output from T2 */
+#define V_SCLK			(V_OSCK >> 1)
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS	1
+#define CONFIG_INITRD_TAG		1
+#define CONFIG_REVISION_TAG		1
+
+/*
+ * NS16550 Configuration
+ */
+
+#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK
+
+/* select serial console configuration */
+#define CONFIG_CONS_INDEX		3
+#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
+#define CONFIG_SERIAL3			3
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_MMC			1
+#define CONFIG_OMAP3_MMC		1
+#define CONFIG_DOS_PARTITION		1
+
+/* DDR  */
+#define CONFIG_OMAP3_NUMONYX_DDR	1
+
+/* USB */
+#define CONFIG_MUSB_UDC			1
+#define CONFIG_USB_OMAP3		1
+#define CONFIG_TWL4030_USB		1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE		1
+#define CONFIG_USB_TTY			1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID		0x0451
+#define CONFIG_USBD_PRODUCTID		0x5678
+#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME	"IGEP"
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
+#define CONFIG_CMD_FAT		/* FAT support			*/
+#define CONFIG_CMD_I2C		/* I2C serial bus support	*/
+#define CONFIG_CMD_MMC		/* MMC support			*/
+#define CONFIG_CMD_ONENAND	/* ONENAND support		*/
+#define CONFIG_CMD_NET		/* bootp, tftpboot, rarpboot	*/
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NFS		/* NFS support			*/
+#define CONFIG_CMD_MTDPARTS	/* Enable MTD parts commands	*/
+#define CONFIG_MTD_DEVICE
+
+#undef CONFIG_CMD_FLASH		/* flinfo, erase, protect	*/
+#undef CONFIG_CMD_IMLS		/* List all found images	*/
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_HARD_I2C			1
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_SLAVE		1
+#define CONFIG_SYS_I2C_BUS		0
+#define CONFIG_SYS_I2C_BUS_SELECT	1
+#define CONFIG_DRIVER_OMAP34XX_I2C	1
+
+/*
+ * TWL4030
+ */
+#define CONFIG_TWL4030_POWER		1
+
+/* Environment information */
+#define CONFIG_BOOTCOMMAND \
+	"mmc init 0 ; fatload mmc 0 0x80000000 setup.ini ; source \0"
+
+#define CONFIG_BOOTDELAY		3
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"usbtty=cdc_acm\0"
+
+#define CONFIG_AUTO_COMPLETE		1
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		"U-Boot # "
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)	/* memtest */
+								/* works on */
+#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
+					0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)	/* default */
+							/* load address */
+
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)
+
+/*
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV			2       /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ			1000
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
+
+/*
+ * Physical Memory Map
+ *
+ */
+#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
+#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 meg */
+#define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C		1
+
+/*
+ * FLASH and environment organization
+ */
+
+#define PISMO1_ONEN_SIZE		GPMC_SIZE_128M /* Configure the PISMO */
+
+#define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
+
+#define ONENAND_ENV_OFFSET		0x260000 /* environment starts here */
+
+#define CONFIG_ENV_IS_IN_ONENAND	1
+#define CONFIG_ENV_SIZE			(512 << 10) /* Total Size Environment */
+#define CONFIG_ENV_ADDR			ONENAND_ENV_OFFSET
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
+#define CONFIG_SYS_GBL_DATA_SIZE	128 /* bytes for initial data */
+
+/*
+ * SMSC911x Ethernet
+ */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_32_BIT
+#define CONFIG_SMC911X_BASE	0x2C000000
+#endif /* (CONFIG_CMD_NET) */
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/igep0030.h b/include/configs/igep0030.h
new file mode 100644
index 0000000..5e2e0ed
--- /dev/null
+++ b/include/configs/igep0030.h
@@ -0,0 +1,215 @@
+/*
+ * (C) Copyright 2010
+ * ISEE 2007 SL, <www.iseebcn.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMV7		1	/* This is an ARM V7 CPU core */
+#define CONFIG_OMAP		1	/* in a TI OMAP core */
+#define CONFIG_OMAP34XX		1	/* which is a 34XX */
+#define CONFIG_OMAP3430		1	/* which is in a 3430 */
+#define CONFIG_OMAP3_IGEP0030	1	/* working with IGEP0030 */
+
+#define CONFIG_SDRC	/* The chip has SDRC controller */
+
+#include <asm/arch/cpu.h>
+#include <asm/arch/omap3.h>
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO		1
+#define CONFIG_DISPLAY_BOARDINFO	1
+
+/* Clock Defines */
+#define V_OSCK			26000000	/* Clock output from T2 */
+#define V_SCLK			(V_OSCK >> 1)
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS	1
+#define CONFIG_INITRD_TAG		1
+#define CONFIG_REVISION_TAG		1
+
+/*
+ * NS16550 Configuration
+ */
+
+#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK
+
+/* select serial console configuration */
+#define CONFIG_CONS_INDEX		3
+#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
+#define CONFIG_SERIAL3			3
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_MMC			1
+#define CONFIG_OMAP3_MMC		1
+#define CONFIG_DOS_PARTITION		1
+
+/* DDR  */
+#define CONFIG_OMAP3_NUMONYX_DDR	1
+
+/* USB */
+#define CONFIG_MUSB_UDC			1
+#define CONFIG_USB_OMAP3		1
+#define CONFIG_TWL4030_USB		1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE		1
+#define CONFIG_USB_TTY			1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID		0x0451
+#define CONFIG_USBD_PRODUCTID		0x5678
+#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME	"IGEP"
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
+#define CONFIG_CMD_FAT		/* FAT support			*/
+#define CONFIG_CMD_I2C		/* I2C serial bus support	*/
+#define CONFIG_CMD_MMC		/* MMC support			*/
+#define CONFIG_CMD_ONENAND	/* ONENAND support		*/
+#define CONFIG_CMD_MTDPARTS	/* Enable MTD parts commands	*/
+#define CONFIG_MTD_DEVICE
+
+#undef CONFIG_CMD_NET		/* bootp, tftpboot, rarpboot	*/
+#undef CONFIG_CMD_FLASH		/* flinfo, erase, protect	*/
+#undef CONFIG_CMD_IMLS		/* List all found images	*/
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_HARD_I2C			1
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_SLAVE		1
+#define CONFIG_SYS_I2C_BUS		0
+#define CONFIG_SYS_I2C_BUS_SELECT	1
+#define CONFIG_DRIVER_OMAP34XX_I2C	1
+
+/*
+ * TWL4030
+ */
+#define CONFIG_TWL4030_POWER		1
+
+/* Environment information */
+#define CONFIG_BOOTCOMMAND \
+	"mmc init 0 ; fatload mmc 0 0x80000000 setup.ini ; source \0"
+
+#define CONFIG_BOOTDELAY		3
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"usbtty=cdc_acm\0"
+
+#define CONFIG_AUTO_COMPLETE		1
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		"U-Boot # "
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)	/* memtest */
+								/* works on */
+#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
+					0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)	/* default */
+							/* load address */
+
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)
+
+/*
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV			2       /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ			1000
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
+
+/*
+ * Physical Memory Map
+ *
+ */
+#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
+#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 meg */
+#define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C		1
+
+/*
+ * FLASH and environment organization
+ */
+
+#define PISMO1_ONEN_SIZE		GPMC_SIZE_128M /* Configure the PISMO */
+
+#define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
+
+#define ONENAND_ENV_OFFSET		0x260000 /* environment starts here */
+
+#define CONFIG_ENV_IS_IN_ONENAND	1
+#define CONFIG_ENV_SIZE			(512 << 10) /* Total Size Environment */
+#define CONFIG_ENV_ADDR			ONENAND_ENV_OFFSET
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
+#define CONFIG_SYS_GBL_DATA_SIZE	128 /* bytes for initial data */
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 1bd0f37..bbb1073 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -95,8 +95,9 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}
+#define CONFIG_GENERIC_MMC		1
 #define CONFIG_MMC			1
-#define CONFIG_OMAP3_MMC		1
+#define CONFIG_OMAP_HSMMC		1
 #define CONFIG_DOS_PARTITION		1
 
 /* DDR - I use Micron DDR */
@@ -111,11 +112,6 @@
 #define CONFIG_USB_DEVICE		1
 #define CONFIG_USB_TTY			1
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID		0x0451
-#define CONFIG_USBD_PRODUCTID		0x5678
-#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME	"Beagle"
 
 /* commands to include */
 #include <config_cmd_default.h>
@@ -189,6 +185,7 @@
 	"vram=12M\0" \
 	"dvimode=1024x768MR-16@60\0" \
 	"defaultdisplay=dvi\0" \
+	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"nandroot=/dev/mtdblock4 rw\0" \
@@ -209,10 +206,10 @@
 		"omapdss.def_disp=${defaultdisplay} " \
 		"root=${nandroot} " \
 		"rootfstype=${nandrootfstype}\0" \
-	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source ${loadaddr}\0" \
-	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+	"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"bootm ${loadaddr}\0" \
@@ -222,7 +219,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmc init; then " \
+	"if mmc rescan ${mmcdev}; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index a0e0f24..69f9126 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -87,8 +87,9 @@
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600, \
 					115200}
+#define CONFIG_GENERIC_MMC		1
 #define CONFIG_MMC			1
-#define CONFIG_OMAP3_MMC		1
+#define CONFIG_OMAP_HSMMC		1
 #define CONFIG_DOS_PARTITION		1
 
 /* DDR - I use Micron DDR */
@@ -97,6 +98,7 @@
 /* commands to include */
 #include <config_cmd_default.h>
 
+#define CONFIG_CMD_CACHE
 #define CONFIG_CMD_EXT2		/* EXT2 Support			*/
 #define CONFIG_CMD_FAT		/* FAT support			*/
 #define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
@@ -158,6 +160,7 @@
 	"vram=12M\0" \
 	"dvimode=1024x768MR-16@60\0" \
 	"defaultdisplay=dvi\0" \
+	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"nandroot=/dev/mtdblock4 rw\0" \
@@ -178,10 +181,10 @@
 		"omapdss.def_disp=${defaultdisplay} " \
 		"root=${nandroot} " \
 		"rootfstype=${nandrootfstype}\0" \
-	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source ${loadaddr}\0" \
-	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+	"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"bootm ${loadaddr}\0" \
@@ -191,7 +194,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmc init; then " \
+	"if mmc rescan ${mmcdev}; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -321,4 +324,7 @@ extern unsigned int boot_flash_type;
 
 #endif /* (CONFIG_CMD_NET) */
 
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		(LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+
 #endif				/* __CONFIG_H */
diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h
index a0d27a4..b52ca19 100644
--- a/include/configs/omap4_panda.h
+++ b/include/configs/omap4_panda.h
@@ -89,7 +89,6 @@
 #define CONFIG_SYS_NS16550_COM3		UART3_BASE
 
 #define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_ENV_OVERWRITE
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}
@@ -107,8 +106,9 @@
 #define CONFIG_TWL6030_POWER		1
 
 /* MMC */
+#define CONFIG_GENERIC_MMC		1
 #define CONFIG_MMC			1
-#define CONFIG_OMAP3_MMC		1
+#define CONFIG_OMAP_HSMMC		1
 #define CONFIG_SYS_MMC_SET_DEV		1
 #define CONFIG_DOS_PARTITION		1
 
@@ -120,11 +120,6 @@
 #define CONFIG_USB_DEVICE		1
 #define CONFIG_USB_TTY			1
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID		0x0451
-#define CONFIG_USBD_PRODUCTID		0x5678
-#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME	"OMAP4 Panda"
 
 /* Flash */
 #define CONFIG_SYS_NO_FLASH	1
@@ -144,18 +139,11 @@
 #undef CONFIG_CMD_IMLS		/* List all found images        */
 
 /*
- * Enabling relocation of u-boot by default
- * Relocation can be skipped if u-boot is copied to the TEXT_BASE
- */
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
-/*
  * Environment setup
  */
 
 #define CONFIG_BOOTDELAY	3
 
-/* allow overwriting serial config and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -163,7 +151,7 @@
 	"console=ttyS2,115200n8\0" \
 	"usbtty=cdc_acm\0" \
 	"vram=16M\0" \
-	"mmcdev=1\0" \
+	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"mmcargs=setenv bootargs console=${console} " \
@@ -179,7 +167,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmc init ${mmcdev}; then " \
+	"if mmc rescan ${mmcdev}; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -239,4 +227,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	1
 
+#define CONFIG_SYS_SDRAM_BASE		0x80000000
+#define CONFIG_SYS_INIT_SP_ADDR		(LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */
diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h
index d5439f9..174d73f 100644
--- a/include/configs/omap4_sdp4430.h
+++ b/include/configs/omap4_sdp4430.h
@@ -63,10 +63,10 @@
 
 /*
  * Size of malloc() pool
- * Total Size Environment - 256k
+ * Total Size Environment - 128k
  * Malloc - add 256k
  */
-#define CONFIG_ENV_SIZE			(256 << 10)
+#define CONFIG_ENV_SIZE			(128 << 10)
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (256 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
@@ -89,12 +89,9 @@
 #define CONFIG_CONS_INDEX		3
 #define CONFIG_SYS_NS16550_COM3		UART3_BASE
 
-#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_ENV_OVERWRITE
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}
-
 /* I2C  */
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED		100000
@@ -108,11 +105,17 @@
 #define CONFIG_TWL6030_POWER		1
 
 /* MMC */
+#define CONFIG_GENERIC_MMC		1
 #define CONFIG_MMC			1
-#define CONFIG_OMAP3_MMC		1
+#define CONFIG_OMAP_HSMMC		1
 #define CONFIG_SYS_MMC_SET_DEV		1
 #define CONFIG_DOS_PARTITION		1
 
+/* MMC ENV related defines */
+#define CONFIG_ENV_IS_IN_MMC		1
+#define CONFIG_SYS_MMC_ENV_DEV		1	/* SLOT2: eMMC(1) */
+#define CONFIG_ENV_OFFSET		0xE0000
+
 /* USB */
 #define CONFIG_MUSB_UDC			1
 #define CONFIG_USB_OMAP3		1
@@ -121,11 +124,6 @@
 #define CONFIG_USB_DEVICE		1
 #define CONFIG_USB_TTY			1
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
-/* Change these to suit your needs */
-#define CONFIG_USBD_VENDORID		0x0451
-#define CONFIG_USBD_PRODUCTID		0x5678
-#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME	"SDP4430"
 
 /* Flash */
 #define CONFIG_SYS_NO_FLASH	1
@@ -138,6 +136,7 @@
 #define CONFIG_CMD_FAT		/* FAT support                  */
 #define CONFIG_CMD_I2C		/* I2C serial bus support	*/
 #define CONFIG_CMD_MMC		/* MMC support                  */
+#define CONFIG_CMD_SAVEENV
 
 /* Disabled commands */
 #undef CONFIG_CMD_NET
@@ -145,18 +144,11 @@
 #undef CONFIG_CMD_IMLS		/* List all found images        */
 
 /*
- * Enabling relocation of u-boot by default
- * Relocation can be skipped if u-boot is copied to the TEXT_BASE
- */
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
-/*
  * Environment setup
  */
 
 #define CONFIG_BOOTDELAY	3
 
-/* allow overwriting serial config and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -164,7 +156,7 @@
 	"console=ttyS2,115200n8\0" \
 	"usbtty=cdc_acm\0" \
 	"vram=16M\0" \
-	"mmcdev=1\0" \
+	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"mmcargs=setenv bootargs console=${console} " \
@@ -180,7 +172,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmc init ${mmcdev}; then " \
+	"if mmc rescan ${mmcdev}; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -240,4 +232,7 @@
  */
 #define CONFIG_NR_DRAM_BANKS	1
 
+#define CONFIG_SYS_SDRAM_BASE		0x80000000
+#define CONFIG_SYS_INIT_SP_ADDR		(LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */
diff --git a/include/configs/qong.h b/include/configs/qong.h
index 7f284ef..f26ced1 100644
--- a/include/configs/qong.h
+++ b/include/configs/qong.h
@@ -66,8 +66,11 @@
 #define CONFIG_FSL_PMIC_MODE	(SPI_MODE_0 | SPI_CS_HIGH)
 
 /* FPGA */
+#define CONFIG_FPGA
 #define CONFIG_QONG_FPGA	1
 #define CONFIG_FPGA_BASE	(CS1_BASE)
+#define CONFIG_FPGA_LATTICE
+#define CONFIG_FPGA_COUNT	1
 
 #ifdef CONFIG_QONG_FPGA
 /* Ethernet */
@@ -86,6 +89,22 @@
 #define CONFIG_BMP_16BPP
 #define CONFIG_DISPLAY_COM57H5M10XRC
 
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI			/* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORT	2
+#define CONFIG_MXC_USB_PORTSC	(MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
+#define CONFIG_MXC_USB_FLAGS	MXC_EHCI_POWER_PINS_ENABLED
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_CMD_FAT
+#endif /* CONFIG_CMD_USB */
+
 /*
  * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
  * initial TFTP transfer, should the user wish one, significantly.
@@ -247,7 +266,7 @@ extern int qong_nand_rdy(void *chip);
 #define	CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x60000)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x80000)
 
 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
diff --git a/include/fpga.h b/include/fpga.h
index 84d7b9f..ac24f2b 100644
--- a/include/fpga.h
+++ b/include/fpga.h
@@ -61,6 +61,7 @@ typedef enum {			/* typedef fpga_type */
 	fpga_min_type,		/* range check value */
 	fpga_xilinx,		/* Xilinx Family) */
 	fpga_altera,		/* unimplemented */
+	fpga_lattice,		/* Lattice family */
 	fpga_undefined		/* invalid range check value */
 } fpga_type;			/* end, typedef fpga_type */
 
diff --git a/include/lattice.h b/include/lattice.h
new file mode 100755
index 0000000..33d2ac3
--- /dev/null
+++ b/include/lattice.h
@@ -0,0 +1,319 @@
+/*
+ * Porting to U-Boot:
+ *
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
+ *
+ * Lattice's ispVME Embedded Tool to load Lattice's FPGA:
+ *
+ * Lattice Semiconductor Corp. Copyright 2009
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef _VME_OPCODE_H
+#define _VME_OPCODE_H
+
+#define VME_VERSION_NUMBER "12.1"
+
+/* Maximum declarations. */
+
+#define VMEHEXMAX	60000L	/* The hex file is split 60K per file. */
+#define SCANMAX		64000L	/* The maximum SDR/SIR burst. */
+
+/*
+ *
+ * Supported JTAG state transitions.
+ *
+ */
+
+#define RESET		0x00
+#define IDLE		0x01
+#define IRPAUSE		0x02
+#define DRPAUSE		0x03
+#define SHIFTIR		0x04
+#define SHIFTDR		0x05
+/* 11/15/05 Nguyen changed to support DRCAPTURE*/
+#define DRCAPTURE	0x06
+
+/*
+ * Flow control register bit definitions.  A set bit indicates
+ * that the register currently exhibits the corresponding mode.
+ */
+
+#define INTEL_PRGM	0x0001	/* Intelligent programming is in effect. */
+#define CASCADE		0x0002	/* Currently splitting large SDR. */
+#define REPEATLOOP	0x0008	/* Currently executing a repeat loop. */
+#define SHIFTRIGHT	0x0080	/* The next data stream needs a right shift. */
+#define SHIFTLEFT	0x0100	/* The next data stream needs a left shift. */
+#define VERIFYUES	0x0200	/* Continue if fail is in effect. */
+
+/*
+ * DataType register bit definitions.  A set bit indicates
+ * that the register currently holds the corresponding type of data.
+ */
+
+#define EXPRESS		0x0001    /* Simultaneous program and verify. */
+#define SIR_DATA	0x0002    /* SIR is the active SVF command. */
+#define SDR_DATA	0x0004    /* SDR is the active SVF command. */
+#define COMPRESS	0x0008    /* Data is compressed. */
+#define TDI_DATA	0x0010    /* TDI data is present. */
+#define TDO_DATA	0x0020    /* TDO data is present. */
+#define MASK_DATA	0x0040    /* MASK data is present. */
+#define HEAP_IN		0x0080    /* Data is from the heap. */
+#define LHEAP_IN	0x0200    /* Data is from intel data buffer. */
+#define VARIABLE	0x0400    /* Data is from a declared variable. */
+#define CRC_DATA	0x0800	 /* CRC data is pressent. */
+#define CMASK_DATA	0x1000    /* CMASK data is pressent. */
+#define RMASK_DATA	0x2000	 /* RMASK data is pressent. */
+#define READ_DATA	0x4000    /* READ data is pressent. */
+#define DMASK_DATA	0x8000	 /* DMASK data is pressent. */
+
+/*
+ *
+ * Pin opcodes.
+ *
+ */
+
+#define signalENABLE	0x1C    /* ispENABLE pin. */
+#define signalTMS	0x1D    /* TMS pin. */
+#define signalTCK	0x1E    /* TCK pin. */
+#define signalTDI	0x1F    /* TDI pin. */
+#define signalTRST	0x20    /* TRST pin. */
+
+/*
+ *
+ * Supported vendors.
+ *
+ */
+
+#define VENDOR		0x56
+#define LATTICE		0x01
+#define ALTERA		0x02
+#define XILINX		0x03
+
+/*
+ * Opcode definitions.
+ *
+ * Note: opcodes must be unique.
+ */
+
+#define ENDDATA		0x00	/* The end of the current SDR data stream. */
+#define RUNTEST		0x01	/* The duration to stay at the stable state. */
+#define ENDDR		0x02	/* The stable state after SDR. */
+#define ENDIR		0x03	/* The stable state after SIR. */
+#define ENDSTATE	0x04	/* The stable state after RUNTEST. */
+#define TRST		0x05	/* Assert the TRST pin. */
+#define HIR		0x06	/*
+				 * The sum of the IR bits of the
+				 * leading devices.
+				 */
+#define TIR		0x07	/*
+				 * The sum of the IR bits of the trailing
+				 * devices.
+				 */
+#define HDR		0x08	/* The number of leading devices. */
+#define TDR		0x09	/* The number of trailing devices. */
+#define ispEN		0x0A	/* Assert the ispEN pin. */
+#define FREQUENCY	0x0B	/*
+				 * The maximum clock rate to run the JTAG state
+				 * machine.
+				 */
+#define STATE		0x10	/* Move to the next stable state. */
+#define SIR		0x11	/* The instruction stream follows. */
+#define SDR		0x12	/* The data stream follows. */
+#define TDI		0x13	/* The following data stream feeds into
+					the device. */
+#define TDO		0x14	/*
+				 * The following data stream is compared against
+				 * the device.
+				 */
+#define MASK		0x15	/* The following data stream is used as mask. */
+#define XSDR		0x16	/*
+				 * The following data stream is for simultaneous
+				 * program and verify.
+				 */
+#define XTDI		0x17	/* The following data stream is for shift in
+				 * only. It must be stored for the next
+				 * XSDR.
+				 */
+#define XTDO		0x18	/*
+				 * There is not data stream.  The data stream
+				 * was stored from the previous XTDI.
+				 */
+#define MEM		0x19	/*
+				 * The maximum memory needed to allocate in
+				 * order hold one row of data.
+				 */
+#define WAIT		0x1A	/* The duration of delay to observe. */
+#define TCK		0x1B	/* The number of TCK pulses. */
+#define SHR		0x23	/*
+				 * Set the flow control register for
+				 * right shift
+				 */
+#define SHL		0x24	/*
+				 * Set the flow control register for left shift.
+				 */
+#define HEAP		0x32	/* The memory size needed to hold one loop. */
+#define REPEAT		0x33	/* The beginning of the loop. */
+#define LEFTPAREN	0x35	/* The beginning of data following the loop. */
+#define VAR		0x55	/* Plac holder for loop data. */
+#define SEC		0x1C	/*
+				 * The delay time in seconds that must be
+				 * observed.
+				 */
+#define SMASK		0x1D	/* The mask for TDI data. */
+#define MAX_WAIT	0x1E	/* The absolute maximum wait time. */
+#define ON		0x1F	/* Assert the targeted pin. */
+#define OFF		0x20	/* Dis-assert the targeted pin. */
+#define SETFLOW		0x30	/* Change the flow control register. */
+#define RESETFLOW	0x31	/* Clear the flow control register. */
+
+#define CRC		0x47	/*
+				 * The following data stream is used for CRC
+				 * calculation.
+				 */
+#define CMASK		0x48	/*
+				 * The following data stream is used as mask
+				 * for CRC calculation.
+				 */
+#define RMASK		0x49	/*
+				 * The following data stream is used as mask
+				 * for read and save.
+				 */
+#define READ		0x50	/*
+				 * The following data stream is used for read
+				 * and save.
+				 */
+#define ENDLOOP		0x59	/* The end of the repeat loop. */
+#define SECUREHEAP	0x60	/* Used to secure the HEAP opcode. */
+#define VUES		0x61	/* Support continue if fail. */
+#define DMASK		0x62	/*
+				 * The following data stream is used for dynamic
+				 * I/O.
+				 */
+#define COMMENT		0x63	/* Support SVF comments in the VME file. */
+#define HEADER		0x64	/* Support header in VME file. */
+#define FILE_CRC	0x65	/* Support crc-protected VME file. */
+#define LCOUNT		0x66	/* Support intelligent programming. */
+#define LDELAY		0x67	/* Support intelligent programming. */
+#define LSDR		0x68	/* Support intelligent programming. */
+#define LHEAP		0x69	/*
+				 * Memory needed to hold intelligent data
+				 * buffer
+				 */
+#define CONTINUE	0x70	/* Allow continuation. */
+#define LVDS		0x71	/* Support LVDS. */
+#define ENDVME		0x7F	/* End of the VME file. */
+#define ENDFILE		0xFF	/* End of file. */
+
+/*
+ *
+ * ispVM Embedded Return Codes.
+ *
+ */
+
+#define VME_VERIFICATION_FAILURE	-1
+#define VME_FILE_READ_FAILURE		-2
+#define VME_VERSION_FAILURE		-3
+#define VME_INVALID_FILE		-4
+#define VME_ARGUMENT_FAILURE		-5
+#define VME_CRC_FAILURE			-6
+
+#define g_ucPinTDI	0x01
+#define g_ucPinTCK	0x02
+#define g_ucPinTMS	0x04
+#define g_ucPinENABLE	0x08
+#define g_ucPinTRST	0x10
+
+/*
+ *
+ * Type definitions.
+ *
+ */
+
+/* Support LVDS */
+typedef struct {
+	unsigned short usPositiveIndex;
+	unsigned short usNegativeIndex;
+	unsigned char  ucUpdate;
+} LVDSPair;
+
+typedef enum {
+	min_lattice_iface_type,		/* insert all new types after this */
+	lattice_jtag_mode,		/* jtag/tap  */
+	max_lattice_iface_type		/* insert all new types before this */
+} Lattice_iface;
+
+typedef enum {
+	min_lattice_type,
+	Lattice_XP2,			/* Lattice XP2 Family */
+	max_lattice_type		/* insert all new types before this */
+} Lattice_Family;
+
+typedef struct {
+	Lattice_Family	family;	/* part type */
+	Lattice_iface	iface;	/* interface type */
+	size_t		size;	/* bytes of data part can accept */
+	void		*iface_fns; /* interface function table */
+	void		*base;	/* base interface address */
+	int		cookie;	/* implementation specific cookie */
+	char		*desc;	/* description string */
+} Lattice_desc;			/* end, typedef Altera_desc */
+
+/* Lattice Model Type */
+#define CONFIG_SYS_XP2		CONFIG_SYS_FPGA_DEV(0x1)
+
+/* Board specific implementation specific function types */
+typedef void (*Lattice_jtag_init)(void);
+typedef void (*Lattice_jtag_set_tdi)(int v);
+typedef void (*Lattice_jtag_set_tms)(int v);
+typedef void (*Lattice_jtag_set_tck)(int v);
+typedef int (*Lattice_jtag_get_tdo)(void);
+
+typedef struct {
+	Lattice_jtag_init	jtag_init;
+	Lattice_jtag_set_tdi	jtag_set_tdi;
+	Lattice_jtag_set_tms	jtag_set_tms;
+	Lattice_jtag_set_tck	jtag_set_tck;
+	Lattice_jtag_get_tdo	jtag_get_tdo;
+} lattice_board_specific_func;
+
+void writePort(unsigned char pins, unsigned char value);
+unsigned char readPort(void);
+void sclock(void);
+void ispVMDelay(unsigned short int a_usMicroSecondDelay);
+void calibration(void);
+
+int lattice_load(Lattice_desc *desc, void *buf, size_t bsize);
+int lattice_dump(Lattice_desc *desc, void *buf, size_t bsize);
+int lattice_info(Lattice_desc *desc);
+
+void ispVMStart(void);
+void ispVMEnd(void);
+signed char ispVMCode(void);
+void ispVMDelay(unsigned short int a_usMicroSecondDelay);
+void ispVMCalculateCRC32(unsigned char a_ucData);
+unsigned char GetByte(void);
+void writePort(unsigned char pins, unsigned char value);
+unsigned char readPort(void);
+void sclock(void);
+#endif
+