* Cleanup lowboot code for MPC5200

* Minor code cleanup (coding style)

* Patch by Reinhard Meyer, 30 Dec 2003:
  - cpu/mpc5xxx/fec.c: added CONFIG_PHY_ADDR, added CONFIG_PHY_TYPE,
  - added CONFIG_PHY_ADDR to include/configs/IceCube.h,
  - turned debug print of PHY registers into a function (called in two places)
  - added support for EMK MPC5200 based modules

* Fix MPC8xx PLPRCR_MFD_SHIFT typo

* Add support for TQM866M modules

* Fixes for TQM855M with 4 MB flash (Am29DL163 = _no_ mirror bit flash)

* Fix a few compiler warnings

16 files changed, 758 insertions, 163 deletions

diff --git a/include/asm-m68k/ptrace.h b/include/asm-m68k/ptrace.h
index 343a9f4..8205518 100644
--- a/include/asm-m68k/ptrace.h
+++ b/include/asm-m68k/ptrace.h
@@ -105,4 +105,3 @@ struct pt_regs {
 #define PT_FPSCR (PT_FPR0 + 2*32 + 1)
 
 #endif
-
diff --git a/include/asm-m68k/u-boot.h b/include/asm-m68k/u-boot.h
index eaf1de7..b414490 100644
--- a/include/asm-m68k/u-boot.h
+++ b/include/asm-m68k/u-boot.h
@@ -39,9 +39,9 @@ typedef struct bd_info {
 	unsigned long	bi_sramstart;	/* start of SRAM memory */
 	unsigned long	bi_sramsize;	/* size	 of SRAM memory */
 	unsigned long	bi_bootflags;	/* boot / reboot flag (for LynxOS) */
-        unsigned long   bi_boot_params; /* where this board expects params */
+	unsigned long	bi_boot_params; /* where this board expects params */
 	unsigned long	bi_ip_addr;	/* IP Address */
-	unsigned char	bi_enetaddr[6];	/* Ethernet adress */
+	unsigned char	bi_enetaddr[6]; /* Ethernet adress */
 	unsigned short	bi_ethspeed;	/* Ethernet speed in Mbps */
 	unsigned long	bi_intfreq;	/* Internal Freq, in MHz */
 	unsigned long	bi_busfreq;	/* Bus Freq, in MHz */
@@ -56,11 +56,11 @@ typedef struct bd_info {
  *
  * Keep it *SMALL* and remember to set CFG_INIT_DATA_SIZE > sizeof(init_data_t)
  */
-typedef	struct	init_data {
+typedef struct	init_data {
 	unsigned long	cpu_clk;	/* VCOOUT = CPU clock in Hz!		*/
 	unsigned long	env_addr;	/* Address  of Environment struct	*/
 	unsigned long	env_valid;	/* Checksum of Environment valid?	*/
-	unsigned long	relocated;	/* Relocat. offset when running in RAM 	*/
+	unsigned long	relocated;	/* Relocat. offset when running in RAM	*/
 	unsigned long	have_console;	/* serial_init() was called		*/
 #ifdef CONFIG_LCD
 	unsigned long	lcd_base;	/* Base address of LCD frambuffer mem	*/
diff --git a/include/asm-mips/addrspace.h b/include/asm-mips/addrspace.h
index 1fd00cc..845dd7c 100644
--- a/include/asm-mips/addrspace.h
+++ b/include/asm-mips/addrspace.h
@@ -14,21 +14,21 @@
 /*
  * Memory segments (32bit kernel mode addresses)
  */
-#define KUSEG                   0x00000000
-#define KSEG0                   0x80000000
-#define KSEG1                   0xa0000000
-#define KSEG2                   0xc0000000
-#define KSEG3                   0xe0000000
+#define KUSEG			0x00000000
+#define KSEG0			0x80000000
+#define KSEG1			0xa0000000
+#define KSEG2			0xc0000000
+#define KSEG3			0xe0000000
 
-#define K0BASE  KSEG0
+#define K0BASE	KSEG0
 
 /*
  * Returns the kernel segment base of a given address
  */
 #ifndef __ASSEMBLY__
-#define KSEGX(a)                (((unsigned long)(a)) & 0xe0000000)
+#define KSEGX(a)		(((unsigned long)(a)) & 0xe0000000)
 #else
-#define KSEGX(a)                ((a) & 0xe0000000)
+#define KSEGX(a)		((a) & 0xe0000000)
 #endif
 
 /*
@@ -40,8 +40,8 @@
 #define PHYSADDR(a)		((a) & 0x1fffffff)
 #endif
 
-/* 
- * Returns the uncached address of a sdram address 
+/*
+ * Returns the uncached address of a sdram address
  */
 #ifndef __ASSEMBLY__
 #ifdef CONFIG_AU1X00
@@ -49,7 +49,7 @@
    cannot access physical memory directly from core */
 #define UNCACHED_SDRAM(a) (((unsigned long)(a)) | 0x20000000)
 #else	/* !CONFIG_AU1X00 */
-#define UNCACHED_SDRAM(a) PHYSADDR(a) 
+#define UNCACHED_SDRAM(a) PHYSADDR(a)
 #endif	/* CONFIG_AU1X00 */
 #endif	/* __ASSEMBLY__ */
 /*
@@ -70,13 +70,13 @@
 /*
  * Memory segments (64bit kernel mode addresses)
  */
-#define XKUSEG                  0x0000000000000000
-#define XKSSEG                  0x4000000000000000
-#define XKPHYS                  0x8000000000000000
-#define XKSEG                   0xc000000000000000
-#define CKSEG0                  0xffffffff80000000
-#define CKSEG1                  0xffffffffa0000000
-#define CKSSEG                  0xffffffffc0000000
-#define CKSEG3                  0xffffffffe0000000
+#define XKUSEG			0x0000000000000000
+#define XKSSEG			0x4000000000000000
+#define XKPHYS			0x8000000000000000
+#define XKSEG			0xc000000000000000
+#define CKSEG0			0xffffffff80000000
+#define CKSEG1			0xffffffffa0000000
+#define CKSSEG			0xffffffffc0000000
+#define CKSEG3			0xffffffffe0000000
 
 #endif /* __ASM_MIPS_ADDRSPACE_H */
diff --git a/include/common.h b/include/common.h
index ece5d64..73a5a2e 100644
--- a/include/common.h
+++ b/include/common.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2002
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -49,11 +49,11 @@ typedef volatile unsigned char	vu_char;
 #ifdef CONFIG_MPC860T
 #define CONFIG_MPC86x 1
 #endif
-#if defined(CONFIG_MPC866P) || \
-    defined(CONFIG_MPC866T) || \
-    defined(CONFIG_MPC859T) || \
-    defined(CONFIG_MPC859DSL) || \
-    defined(CONFIG_MPC852T)
+#if defined(CONFIG_MPC852)	|| defined(CONFIG_MPC852T)	|| \
+    defined(CONFIG_MPC859)	|| defined(CONFIG_MPC859T)	|| \
+    defined(CONFIG_MPC859DSL)	|| \
+    defined(CONFIG_MPC866)	|| defined(CONFIG_MPC866T)	|| \
+    defined(CONFIG_MPC866P)
 #define CONFIG_MPC866_et_al 1
 #define CONFIG_MPC86x 1
 #endif
@@ -100,7 +100,7 @@ typedef	void (interrupt_handler_t)(void *);
  */
 #if defined(CONFIG_TQM823M) || defined(CONFIG_TQM850M) || \
     defined(CONFIG_TQM855M) || defined(CONFIG_TQM860M) || \
-    defined(CONFIG_TQM862M)
+    defined(CONFIG_TQM862M) || defined(CONFIG_TQM866M)
 # ifndef CONFIG_TQM8xxM
 #  define CONFIG_TQM8xxM
 # endif
diff --git a/include/commproc.h b/include/commproc.h
index 3da804f..8bab522 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -2,6 +2,9 @@
  * MPC8xx Communication Processor Module.
  * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
  *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
  * This file contains structures and information for the communication
  * processor channels.  Some CPM control and status is available
  * throught the MPC8xx internal memory map.  See immap.h for details.
@@ -1430,11 +1433,12 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00002600)
 #endif	/* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
 
-/***  TQM855L/M, TQM860L/M, TQM862L/M  ********************************/
+/***  TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M  *********************/
 
 #if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
     defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
-    defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M)
+    defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
+    defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
 
 # ifdef CONFIG_SCC1_ENET	/* use SCC for 10Mbps Ethernet	*/
 
diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h
index 2f0a875..194f62f 100644
--- a/include/configs/IceCube.h
+++ b/include/configs/IceCube.h
@@ -215,6 +215,7 @@
  */
 #define CONFIG_MPC5XXX_FEC	1
 #define CONFIG_FEC_10MBIT 1 /* Workaround for FEC 100Mbit problem */
+#define CONFIG_PHY_ADDR		0x00
 
 /*
  * GPIO configuration
diff --git a/include/configs/MVBLUE.h b/include/configs/MVBLUE.h
index 6965e1c..32f9e91 100644
--- a/include/configs/MVBLUE.h
+++ b/include/configs/MVBLUE.h
@@ -53,7 +53,7 @@
 #define ERR_LED(code)
 #endif
 
-#undef DEBUG 
+#undef DEBUG
 
 #define CONFIG_MPC824X		1
 #define CONFIG_MPC8245		1
@@ -71,14 +71,14 @@
 #define CONFIG_BOOT_RETRY_TIME	-1
 
 #define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT		"autoboot in %d seconds (stop with 's')...\n\0"
-#define CONFIG_AUTOBOOT_STOP_STR	"s\0"
+#define CONFIG_AUTOBOOT_PROMPT		"autoboot in %d seconds (stop with 's')...\n"
+#define CONFIG_AUTOBOOT_STOP_STR	"s"
 #define CONFIG_ZERO_BOOTDELAY_CHECK
 #define CONFIG_RESET_TO_RETRY		60
 
 #define CONFIG_COMMANDS		( CFG_CMD_ASKENV | CFG_CMD_BOOTD | CFG_CMD_CACHE | CFG_CMD_DHCP	| \
-							  CFG_CMD_ECHO	 | CFG_CMD_ENV   | CFG_CMD_FLASH | CFG_CMD_IMI	| \
-							  CFG_CMD_IRQ	 | CFG_CMD_NET	 | CFG_CMD_PCI	 | CFG_CMD_RUN   )  
+				  CFG_CMD_ECHO	 | CFG_CMD_ENV   | CFG_CMD_FLASH | CFG_CMD_IMI	| \
+				  CFG_CMD_IRQ	 | CFG_CMD_NET	 | CFG_CMD_PCI	 | CFG_CMD_RUN   )
 
 
 #define CONFIG_BOOTP_MASK   ( 0xffffffff )
@@ -103,19 +103,19 @@
 
 #define CONFIG_NFSBOOTCOMMAND  	"bootp; run nfsargs addcons;bootm"
 
-#define CONFIG_EXTRA_ENV_SETTINGS                   \
-	"console_nr=0\0"								\
-    "dhcp_client_id=mvBOX-XP\0"                     \
-    "dhcp_vendor-class-identifier=mvBOX\0"          \
-    "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0" 	\
-    "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0" 	\
-    "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0" 	\
-    "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0" 								\
-	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "				\
-			"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off\0"			\
-	"addcons=setenv bootargs $(bootargs) console=ttyS$(console_nr),$(baudrate)N8\0"	\
+#define CONFIG_EXTRA_ENV_SETTINGS			\
+	"console_nr=0\0"				\
+    "dhcp_client_id=mvBOX-XP\0"				\
+    "dhcp_vendor-class-identifier=mvBOX\0"		\
+    "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0"	\
+    "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0"	\
+    "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0"	\
+    "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0"	\
+	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+			"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off\0"	\
+	"addcons=setenv bootargs $(bootargs) console=ttyS$(console_nr),$(baudrate)N8\0" \
     "mv_version=" MV_VERSION "\0"	\
-	"bootretry=30\0"			
+	"bootretry=30\0"
 
 #define CONFIG_OVERWRITE_ETHADDR_ONCE
 
@@ -124,11 +124,11 @@
  *-----------------------------------------------------------------------
  */
 
-#define CONFIG_PCI      	
+#define CONFIG_PCI
 #define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
 
-#define CONFIG_NET_MULTI	
+#define CONFIG_NET_MULTI
 #define CONFIG_NET_RETRY_COUNT 5
 
 #define CONFIG_TULIP
@@ -144,8 +144,8 @@
  */
 #define CFG_SDRAM_BASE	    0x00000000
 
-#define CFG_FLASH_BASE      0xFFF00000  
-#define CFG_MONITOR_BASE    TEXT_BASE    
+#define CFG_FLASH_BASE      0xFFF00000
+#define CFG_MONITOR_BASE    TEXT_BASE
 
 #define CFG_RESET_ADDRESS   0xFFF00100
 #define CFG_EUMB_ADDR	    0xFC000000
@@ -196,7 +196,7 @@
  * For the detail description refer to the MPC8240 user's manual.
  */
 
-#define CONFIG_SYS_CLK_FREQ  33000000	
+#define CONFIG_SYS_CLK_FREQ  33000000
 #define CFG_HZ		     	 10000
 
 /* Bit-field values for MCCR1.  */
@@ -205,17 +205,17 @@
 
 /* Bit-field values for MCCR2.  */
 #define CFG_TSWAIT      0x5
-#define CFG_REFINT      430   
+#define CFG_REFINT      430
 
 /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.  */
-#define CFG_BSTOPRE     121 
+#define CFG_BSTOPRE     121
 
 /* Bit-field values for MCCR3.  */
 #define CFG_REFREC      8
 
 /* Bit-field values for MCCR4.  */
-#define CFG_PRETOACT    3  
-#define CFG_ACTTOPRE    5     
+#define CFG_PRETOACT    3
+#define CFG_ACTTOPRE    5
 #define CFG_ACTORW      3
 #define CFG_SDMODE_CAS_LAT  3
 #define CFG_REGISTERD_TYPE_BUFFER 1
@@ -292,7 +292,7 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#undef  CFG_FLASH_PROTECTION    
+#undef  CFG_FLASH_PROTECTION
 #define CFG_MAX_FLASH_BANKS		1	/* Max number of flash banks		*/
 #define CFG_MAX_FLASH_SECT		63	/* Max number of sectors per flash	*/
 
@@ -300,11 +300,11 @@
 #define CFG_FLASH_WRITE_TOUT	1000
 
 
-#define CFG_ENV_IS_IN_FLASH	    
+#define CFG_ENV_IS_IN_FLASH
 
 #define CFG_ENV_OFFSET		0x00010000
-#define CFG_ENV_SIZE        0x00010000 
-#define CFG_ENV_SECT_SIZE	0x00010000 
+#define CFG_ENV_SIZE		0x00010000
+#define CFG_ENV_SECT_SIZE	0x00010000
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
diff --git a/include/configs/QS860T.h b/include/configs/QS860T.h
index 92eccd3..8d29a31 100644
--- a/include/configs/QS860T.h
+++ b/include/configs/QS860T.h
@@ -47,7 +47,6 @@
 #define CONFIG_ENV_OVERWRITE	1	/* allow overwrite MAC address */
 
 
-
 /*
  * High Level Configuration Options
  * (easy to change)
@@ -368,7 +367,6 @@ CONFIG_SPI
 /* #define CFG_BR5		0xE4000000 */
 
 
-
 /*
  * BR6 and OR6 (Expansion bus)
  * Base address = 0xE800_0000 - 0xEBFF_FFFF
@@ -381,7 +379,6 @@ CONFIG_SPI
 /* #define CFG_BR6		0xE8000000 */
 
 
-
 /*
  * BR7 and OR7 (Expansion bus)
  * Base address = 0xEC00_0000 - 0xEFFF_FFFF
@@ -394,7 +391,6 @@ CONFIG_SPI
 /* #define CFG_BR7		0xE8000000 */
 
 
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h
index 21daa2d..624beed 100644
--- a/include/configs/TOP5200.h
+++ b/include/configs/TOP5200.h
@@ -1,16 +1,17 @@
 /*
  * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.

- *

- * modified for TOP5200 by Reinhard Meyer, www.emk-elektronik.de

- * TOP5200 differences from IceCube:

- * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks

- *   bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins

- * 1 SDRAM/DDRAM Bank up to 256 MB

- * local VPD I2C Bus is software driven and uses

- *   GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL

- * FLASH is located at 0x80000000

- * Internal regs are at 0xfff00000

+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de
+ *
+ * TOP5200 differences from IceCube:
+ * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks
+ *   bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins
+ * 1 SDRAM/DDRAM Bank up to 256 MB
+ * local VPD I2C Bus is software driven and uses
+ *   GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL
+ * FLASH is re-located at 0xff000000
+ * Internal regs are at 0xf0000000
  * Reset jumps to 0x00000100
  *
  * See file CREDITS for list of people who contributed to this
@@ -44,7 +45,7 @@
 #define CONFIG_MPC5200		1	/* More exactly a MPC5200 */
 #define CONFIG_TOP5200		1	/* ... on TOP5200 board - we need this for FEC.C */
 
-#define CFG_MPC5XXX_CLKIN	33333333 /* ... running at 33MHz */
+#define CFG_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
 
 #define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
 #define BOOTFLAG_WARM		0x02	/* Software reboot	     */
@@ -98,17 +99,48 @@
 #include <cmd_confdefs.h>
 
 /*
+ * low boot
+ */
+#if (TEXT_BASE == 0xFF000000)		/* Boot low with 16 MB Flash */
+#   define CFG_LOWBOOT		1
+#   define CFG_LOWBOOT16	1
+#endif
+
+/*
  * Autobooting
  */
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* autoboot command */
-#define CONFIG_BOOTARGS		"root=/dev/ram rw"
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=$(serverip):$(rootpath)\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs $(bootargs) "				\
+		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
+		":$(hostname):$(netdev):off panic=1\0"			\
+	"flash_nfs=run nfsargs addip;"					\
+		"bootm $(kernel_addr)\0"				\
+	"flash_self=run ramargs addip;"					\
+		"bootm $(kernel_addr) $(ramdisk_addr)\0"		\
+	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0"	\
+	"rootpath=/opt/eldk/ppc_82xx\0"					\
+	"bootfile=/tftpboot/MPC5200/uImage\0"				\
+	""
+
+#define CONFIG_BOOTCOMMAND	"run flash_self"
 
 /*
  * IPB Bus clocking configuration.
  */
 #undef CFG_IPBSPEED_133   		/* define for 133MHz speed */
-

+
 /*
  * I2C configuration
  */
@@ -120,21 +152,21 @@
 
 #define CFG_I2C_EEPROM_ADDR_LEN 2
 #define CFG_EEPROM_SIZE 0x2000
-

+
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_MISC_INIT_R
-

+
 #undef	CONFIG_HARD_I2C			/* I2C with hardware support */
 #define	CONFIG_SOFT_I2C		1
-

+
 #if defined (CONFIG_SOFT_I2C)
 #  define SDA0			0x40
 #  define SCL0			0x80
-#  define GPIOE0		*((volatile uchar*)(CFG_MBAR+0x0c00))

-#  define DDR0			*((volatile uchar*)(CFG_MBAR+0x0c08))

-#  define DVO0			*((volatile uchar*)(CFG_MBAR+0x0c0c))

-#  define DVI0			*((volatile uchar*)(CFG_MBAR+0x0c20))

-#  define ODE0			*((volatile uchar*)(CFG_MBAR+0x0c04))

+#  define GPIOE0		*((volatile uchar*)(CFG_MBAR+0x0c00))
+#  define DDR0			*((volatile uchar*)(CFG_MBAR+0x0c08))
+#  define DVO0			*((volatile uchar*)(CFG_MBAR+0x0c0c))
+#  define DVI0			*((volatile uchar*)(CFG_MBAR+0x0c20))
+#  define ODE0			*((volatile uchar*)(CFG_MBAR+0x0c04))
 #  define I2C_INIT		{GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);}
 #  define I2C_READ		((DVI0&SDA0)?1:0)
 #  define I2C_SDA(x)	{if(x)DVO0|=SDA0;else DVO0&=~SDA0;}
@@ -145,12 +177,12 @@
 #  define CFG_I2C_SPEED		100000
 #  define CFG_I2C_SLAVE		0x7F
 #endif
-

-#if defined (CONFIG_HARD_I2C)

+
+#if defined (CONFIG_HARD_I2C)
 #  define CFG_I2C_MODULE	2		/* Select I2C module #1 or #2 */
 #  define CFG_I2C_SPEED		100000	/* 100 kHz */
 #  define CFG_I2C_SLAVE		0x7F
-#endif

+#endif
 
 /*
  * Flash configuration, expect one 16 Megabyte Bank at most
@@ -158,7 +190,7 @@
 #define CFG_FLASH_BASE		0xff000000
 #define CFG_FLASH_SIZE		0x01000000
 #define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0)

+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0)
 
 #define CFG_MAX_FLASH_SECT	256	/* max num of sects on one chip */
 
@@ -167,32 +199,32 @@
 
 #undef CONFIG_FLASH_16BIT	/* Flash is 8-bit */
 
-/*

- * DRAM configuration - will be read from VPD later... TODO!

- */

-#if 0

-/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */

-#define	CFG_DRAM_DDR		0

-#define CFG_DRAM_EMODE		0

-#define CFG_DRAM_MODE		0x008D

-#define CFG_DRAM_CONTROL	0x514F0000

-#define CFG_DRAM_CONFIG1	0xC2233A00

-#define CFG_DRAM_CONFIG2	0x88B70004

-#define	CFG_DRAM_TAP_DEL	0x08

-#define CFG_DRAM_RAM_SIZE	0x19

-#endif

-#if 1

-/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */

-#define	CFG_DRAM_DDR		0

-#define CFG_DRAM_EMODE		0

-#define CFG_DRAM_MODE		0x00CD

-#define CFG_DRAM_CONTROL	0x514F0000

-#define CFG_DRAM_CONFIG1	0xD2333A00

-#define CFG_DRAM_CONFIG2	0x8AD70004

-#define	CFG_DRAM_TAP_DEL	0x08

-#define CFG_DRAM_RAM_SIZE	0x19

-#endif

-

+/*
+ * DRAM configuration - will be read from VPD later... TODO!
+ */
+#if 0
+/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */
+#define	CFG_DRAM_DDR		0
+#define CFG_DRAM_EMODE		0
+#define CFG_DRAM_MODE		0x008D
+#define CFG_DRAM_CONTROL	0x514F0000
+#define CFG_DRAM_CONFIG1	0xC2233A00
+#define CFG_DRAM_CONFIG2	0x88B70004
+#define	CFG_DRAM_TAP_DEL	0x08
+#define CFG_DRAM_RAM_SIZE	0x19
+#endif
+#if 1
+/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */
+#define	CFG_DRAM_DDR		0
+#define CFG_DRAM_EMODE		0
+#define CFG_DRAM_MODE		0x00CD
+#define CFG_DRAM_CONTROL	0x514F0000
+#define CFG_DRAM_CONFIG1	0xD2333A00
+#define CFG_DRAM_CONFIG2	0x8AD70004
+#define	CFG_DRAM_TAP_DEL	0x08
+#define CFG_DRAM_RAM_SIZE	0x19
+#endif
+
 /*
  * Environment settings
  */
@@ -201,17 +233,17 @@
 #define CFG_ENV_SIZE		0x0700
 #define CFG_I2C_EEPROM_ADDR 0x57
 
-/*

- * VPD settings

- */

+/*
+ * VPD settings
+ */
 #define CFG_FACT_OFFSET		0x1800
 #define CFG_FACT_SIZE		0x0800
 #define CFG_I2C_FACT_ADDR	0x57
-

+
 /*
- * Memory map

- *

- * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000

+ * Memory map
+ *
+ * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000
  */
 #define CFG_MBAR			0xf0000000	/* DO NOT CHANGE this */
 #define CFG_SDRAM_BASE		0x00000000
@@ -240,12 +272,12 @@
  */
 #define CONFIG_MPC5XXX_FEC	1
 #define CONFIG_FEC_10MBIT	1		/* Workaround for FEC 100Mbit problem */
-#define	CONFIG_PHY_ADDR		0x1f

+#define	CONFIG_PHY_ADDR		0x1f
 #define	CONFIG_PHY_TYPE		0x79c874
 /*
- * GPIO configuration:

- * PSC1,2,3 predefined as UART

- * PCI disabled

+ * GPIO configuration:
+ * PSC1,2,3 predefined as UART
+ * PCI disabled
  * Ethernet 100 with MD
  */
 #define CFG_GPS_PORT_CONFIG	0x00058444
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index e926d93..cb4a16a 100644
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2003
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -83,6 +83,39 @@
 
 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 
+/* enable I2C and select the hardware/software driver */
+#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
+
+#define CFG_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
+#define CFG_I2C_SLAVE		0xFE
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL		0x00000020	/* PB 26 */
+#define PB_SDA		0x00000010	/* PB 27 */
+
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
+#endif	/* CONFIG_SOFT_I2C */
+
+#define CFG_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C64	*/
+#define CFG_I2C_EEPROM_ADDR_LEN	2		/* two byte address	*/
+#if 0
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* takes up to 10 msec	*/
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CFG_EEPROM_PAGE_WRITE_BITS	5
+#endif
+
 #define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
 
 #define CONFIG_MAC_PARTITION
@@ -93,6 +126,7 @@
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_ASKENV	| \
 				CFG_CMD_DHCP	| \
+				CFG_CMD_EEPROM	| \
 				CFG_CMD_IDE	| \
 				CFG_CMD_DATE	)
 
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
new file mode 100644
index 0000000..0219836
--- /dev/null
+++ b/include/configs/TQM866M.h
@@ -0,0 +1,526 @@
+/*
+ * (C) Copyright 2000-2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC866		1	/* This is a MPC866 CPU		*/
+#define CONFIG_TQM866M		1	/* ...on a TQM8xxM module	*/
+
+#define	CFG_8XX_XIN	10000000 /* XXX XXX XXX */
+
+#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#undef	CONFIG_8xx_CONS_SMC2
+#undef	CONFIG_8xx_CONS_NONE
+
+#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
+
+#define	CONFIG_BOOTCOUNT_LIMIT
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define CONFIG_BOARD_TYPES	1	/* support board types		*/
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=$(serverip):$(rootpath)\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs $(bootargs) "				\
+		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
+		":$(hostname):$(netdev):off panic=1\0"			\
+	"flash_nfs=run nfsargs addip;"					\
+		"bootm $(kernel_addr)\0"				\
+	"flash_self=run ramargs addip;"					\
+		"bootm $(kernel_addr) $(ramdisk_addr)\0"		\
+	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0"	\
+	"rootpath=/opt/eldk/ppc_8xx\0"					\
+	"bootfile=/tftpboot/TQM855M/uImage\0"				\
+	"kernel_addr=40080000\0"					\
+	"ramdisk_addr=40180000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
+
+#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
+
+/* enable I2C and select the hardware/software driver */
+#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
+
+#define CFG_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
+#define CFG_I2C_SLAVE		0xFE
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL		0x00000020	/* PB 26 */
+#define PB_SDA		0x00000010	/* PB 27 */
+
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
+#endif	/* CONFIG_SOFT_I2C */
+
+#define CFG_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C256	*/
+#define CFG_I2C_EEPROM_ADDR_LEN	2		/* two byte address	*/
+#define CFG_EEPROM_PAGE_WRITE_BITS	4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
+
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_ASKENV	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_DATE	)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
+
+#if 0
+#define	CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
+#endif
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE		256	/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS		16	/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/
+
+#define	CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0x40000000
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define	CFG_ENV_IS_IN_FLASH	1
+#define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
+#define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
+#define CFG_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
+#define CFG_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#ifndef	CONFIG_CAN_DRIVER
+#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#else	/* we must activate GPL5 in the SIUMCR for CAN */
+#define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#endif	/* CONFIG_CAN_DRIVER */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ * set PLL multiplication factor
+ */
+#if defined(CONFIG_133MHz)
+    /* for 133 MHz, we use a 10 MHz clock:
+     * MFN = 0x09, MFD = 0x1D, S = 0, MFI = 13
+     */
+#define CFG_PLPRCR							\
+		( 9 << PLPRCR_MFN_SHIFT | 0x1D << PLPRCR_MFD_SHIFT  |	\
+		  0 << PLPRCR_S_SHIFT	| 0x0D << PLPRCR_MFI_SHIFT  |	\
+		  PLPRCR_TEXPS )
+#elif defined(CONFIG_80MHz) /* for  80 MHz, we use a 16 MHz clock *  5 */
+#define CFG_PLPRCR							\
+		( (5-1)<<PLPRCR_MFI_SHIFT | PLPRCR_TEXPS )
+#else			/* up to 66 MHz we use a 1:1 clock */
+#define CFG_PLPRCR	( PLPRCR_SPLSS | PLPRCR_TEXPS )
+#endif	/* CONFIG_??MHz */
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+#if defined(CONFIG_133MHz)  /* for 133 MHz, we use a 10 MHz clock * 13 */
+#define CFG_SCCR	(/* SCCR_TBS  | */ \
+			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+			 SCCR_DFALCD00)
+#elif defined(CONFIG_80MHz) /* for  80 MHz, we use a 16 MHz clock *  5 */
+#define CFG_SCCR	(/* SCCR_TBS  | */ \
+			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+			 SCCR_DFALCD00)
+#else			/* up to 66 MHz we use a 1:1 clock */
+#define CFG_SCCR	(SCCR_TBS     | \
+			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+			 SCCR_DFALCD00)
+#endif	/* CONFIG_??MHz */
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
+#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
+
+#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
+#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#define CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O			*/
+#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers	*/
+#define CFG_ATA_ALT_OFFSET	0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER	0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
+
+/*
+ * FLASH timing:
+ */
+#if defined(CONFIG_133MHz)
+/* 133 MHz CPU - 66 MHz bus: */
+#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
+				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
+#elif defined(CONFIG_100MHz)
+/* 100 MHz CPU - 50 MHz bus: */
+#elif defined(CONFIG_80MHz)
+/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
+				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
+#elif defined(CONFIG_66MHz)
+/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
+				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
+#else		/*   50 MHz */
+/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
+				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
+#endif	/*CONFIG_??MHz */
+
+#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+#define CFG_OR1_REMAP	CFG_OR0_REMAP
+#define CFG_OR1_PRELIM	CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
+#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
+#define	SDRAM_MAX_SIZE		(256 << 20)	/* max 256 MB per bank	*/
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
+#define CFG_OR_TIMING_SDRAM	0x00000A00
+
+#define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#ifndef	CONFIG_CAN_DRIVER
+#define	CFG_OR3_PRELIM	CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
+#define	CFG_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
+#define CFG_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
+#define CFG_OR3_CAN		(CFG_CAN_OR_AM | OR_G5LA | OR_BI)
+#define CFG_BR3_CAN		((CFG_CAN_BASE & BR_BA_MSK) | \
+					BR_PS_8 | BR_MS_UPMB | BR_V )
+#endif	/* CONFIG_CAN_DRIVER */
+
+/*
+ * Memory Periodic Timer Prescaler
+ *
+ * The Divider for PTA (refresh timer) configuration is based on an
+ * example SDRAM configuration (64 MBit, one bank). The adjustment to
+ * the number of chip selects (NCS) and the actually needed refresh
+ * rate is done by setting MPTPR.
+ *
+ * PTA is calculated from
+ *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
+ *
+ *	gclk	  CPU clock (not bus clock!)
+ *	Trefresh  Refresh cycle * 4 (four word bursts used)
+ *
+ * 4096  Rows from SDRAM example configuration
+ * 1000  factor s -> ms
+ *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
+ *    4  Number of refresh cycles per period
+ *   64  Refresh cycle in ms per number of rows
+ * --------------------------------------------
+ * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
+ *
+ * 50 MHz => 50.000.000 / Divider =  98
+ * 66 Mhz => 66.000.000 / Divider = 129
+ * 80 Mhz => 80.000.000 / Divider = 156
+ */
+#if   defined(CONFIG_133MHz)
+#define CFG_MAMR_PTA		129
+#elif defined(CONFIG_100MHz)
+#define CFG_MAMR_PTA		 98
+#elif defined(CONFIG_80MHz)
+#define CFG_MAMR_PTA		156
+#elif defined(CONFIG_66MHz)
+#define CFG_MAMR_PTA		129
+#else		/*   50 MHz */
+#define CFG_MAMR_PTA		 98
+#endif	/*CONFIG_??MHz */
+
+/*
+ * For 16 MBit, refresh rates could be 31.3 us
+ * (= 64 ms / 2K = 125 / quad bursts).
+ * For a simpler initialization, 15.6 us is used instead.
+ *
+ * #define CFG_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
+ * #define CFG_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
+ */
+#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
+#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#define CONFIG_SCC1_ENET
+#define CONFIG_FEC_ENET
+#define CONFIG_ETHPRIME		"SCC ETHERNET"
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/dbau1x00.h b/include/configs/dbau1x00.h
index 6f647f2..d78b727 100644
--- a/include/configs/dbau1x00.h
+++ b/include/configs/dbau1x00.h
@@ -30,24 +30,24 @@
 
 #define CONFIG_MIPS32		1  /* MIPS32 CPU core	*/
 #define CONFIG_DBAU1X00		1
-#define CONFIG_AU1X00           1  /* alchemy series cpu */
+#define CONFIG_AU1X00		1  /* alchemy series cpu */
 
 #ifdef CONFIG_DBAU1000
 /* Also known as Merlot */
-#define CONFIG_AU1000           1
+#define CONFIG_AU1000		1
 #else
 #ifdef CONFIG_DBAU1100
-#define CONFIG_AU1100           1
+#define CONFIG_AU1100		1
 #else
 #ifdef CONFIG_DBAU1500
-#define CONFIG_AU1500           1
-#else  
+#define CONFIG_AU1500		1
+#else
 #error "No valid board set"
 #endif
 #endif
 #endif
 
-#define CONFIG_ETHADDR          DE:AD:BE:EF:01:01    /* Ethernet address */
+#define CONFIG_ETHADDR		DE:AD:BE:EF:01:01    /* Ethernet address */
 
 #define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds	*/
 
@@ -158,7 +158,7 @@
 
 #define CFG_ATA_BASE_ADDR       CFG_PCMCIA_MEM_ADDR
 
-/* Offset for data I/O                  */
+/* Offset for data I/O			*/
 #define CFG_ATA_DATA_OFFSET     8
 
 /* Offset for normal register accesses  */
diff --git a/include/dataflash.h b/include/dataflash.h
index c404016..650454e 100644
--- a/include/dataflash.h
+++ b/include/dataflash.h
@@ -91,7 +91,6 @@ typedef struct _AT91S_DataFlash {
 } AT91S_DataFlash, *AT91PS_DataFlash;
 
 
-
 typedef struct _AT91S_DATAFLASH_INFO {
 
 	AT91S_DataflashDesc Desc;
diff --git a/include/flash.h b/include/flash.h
index 800fb4d..a0c9cad 100644
--- a/include/flash.h
+++ b/include/flash.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000, 2001
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -165,10 +165,13 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
 
 #define AMD_ID_DL640	0x227E227E	/* 29DL640D ID (64 M, dual boot sectors)*/
 #define AMD_ID_MIRROR	0x227E227E	/* 1st ID word for MirrorBit family */
-#define AMD_ID_LV640U_2	0x220C220C	/* 2d ID word for AM29LV640M at 0x38 */
-#define AMD_ID_LV640U_3	0x22012201	/* 3d ID word for AM29LV640M at 0x3c */
-#define AMD_ID_LV128U_2 0x22122212	/* 2d ID word for AM29LV128M at 0x38 */
-#define AMD_ID_LV128U_3 0x22002200	/* 3d ID word for AM29LV128M at 0x3c */
+#define AMD_ID_LV640U_2	0x220C220C	/* 2d ID word for AM29LV640M  at 0x38 */
+#define AMD_ID_LV640U_3	0x22012201	/* 3d ID word for AM29LV640M  at 0x3c */
+#define AMD_ID_LV128U_2 0x22122212	/* 2d ID word for AM29LV128M  at 0x38 */
+#define AMD_ID_LV128U_3 0x22002200	/* 3d ID word for AM29LV128M  at 0x3c */
+
+#define AMD_ID_LV320B_2	0x221A221A	/* 2d ID word for AM29LV320MB at 0x38 */
+#define AMD_ID_LV320B_3 0x22002200	/* 3d ID word for AM29LV320MB at 0x3c */
 
 #define AMD_ID_LV640U	0x22D722D7	/* 29LV640U ID (64 M, uniform sectors)	*/
 
@@ -322,13 +325,15 @@ extern int flash_real_protect(flash_info_t *info, long sector, int prot);
 #define FLASH_28F320C3B 0x009F		/* Intel 28F320C3B ( 32M = 2M x 16 )	*/
 #define FLASH_28F640C3T 0x00A0		/* Intel 28F640C3T ( 64M = 4M x 16 )	*/
 #define FLASH_28F640C3B 0x00A1		/* Intel 28F640C3B ( 64M = 4M x 16 )	*/
-#define FLASH_AMLV320U	0x00A2		/* AMD 29LV128M    ( 128M = 8M x 16 )	*/
+#define FLASH_AMLV320U	0x00A2		/* AMD 29LV320M    ( 32M = 2M x 16 )	*/
 #define FLASH_AMLV640U	0x00A4		/* AMD 29LV640M    ( 64M = 4M x 16 )	*/
 #define FLASH_AMLV128U	0x00A6		/* AMD 29LV128M	   ( 128M = 8M x 16 )	*/
+#define FLASH_AMLV320B  0x00A7		/* AMD 29LV320MB   ( 32M = 2M x 16 )	*/
+#define FLASH_AMLV320T	0x00A8		/* AMD 29LV320MT   ( 32M = 2M x 16 )	*/
 /* Intel 28F256L18T 256M = 128K x 255 + 32k x 4	*/
-#define FLASH_28F256L18T 0x00A8
-#define FLASH_AMDL163T	0x00A2		/* AMD AM29DL163T (2M x 16 )			*/
-#define FLASH_AMDL163B	0x00A3
+#define FLASH_28F256L18T 0x00B0
+#define FLASH_AMDL163T	0x00B2		/* AMD AM29DL163T (2M x 16 )			*/
+#define FLASH_AMDL163B	0x00B3
 
 #define FLASH_UNKNOWN	0xFFFF		/* unknown flash type			*/
 
diff --git a/include/mpc8xx.h b/include/mpc8xx.h
index 4c0c73c..847c2b4 100644
--- a/include/mpc8xx.h
+++ b/include/mpc8xx.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -135,18 +135,18 @@
  * PLPRCR - PLL, Low-Power, and Reset Control Register			15-30
  */
 #ifdef CONFIG_MPC866_et_al
-#define PLPRCR_MF_MSK	0xffff001e	/* Multiplication factor + PDF bits	*/
-#define PLPRCR_MFN_MSK	0xf8000000	/* Multiplication factor numerator bits */
-#define PLPRCR_MFN_SHIFT 0x0000001b	/* Multiplication factor numerator shift*/
-#define PLPRCR_MFD_MSK	0x07c00000	/* Multiplication factor denominator bits */
-#define PLPRCR_MFD_SHIFT 0x00000017	/* Multiplication factor denominator shift*/
+#define PLPRCR_MF_MSK	0xFFFF001E	/* Multiplication factor + PDF bits	*/
+#define PLPRCR_MFN_MSK	0xF8000000	/* Multiplication factor numerator bits */
+#define PLPRCR_MFN_SHIFT	27	/* Multiplication factor numerator shift*/
+#define PLPRCR_MFD_MSK	0x07C00000	/* Multiplication factor denominator bits */
+#define PLPRCR_MFD_SHIFT	22	/* Multiplication factor denominator shift*/
 #define PLPRCR_S_MSK	0x00300000	/* Multiplication factor integer bits	*/
-#define PLPRCR_S_SHIFT	0x00000014	/* Multiplication factor integer shift	*/
-#define PLPRCR_MFI_MSK	0x000f0000	/* Multiplication factor integer bits	*/
-#define PLPRCR_MFI_SHIFT 0x00000010	/* Multiplication factor integer shift	*/
+#define PLPRCR_S_SHIFT		20	/* Multiplication factor integer shift	*/
+#define PLPRCR_MFI_MSK	0x000F0000	/* Multiplication factor integer bits	*/
+#define PLPRCR_MFI_SHIFT	16	/* Multiplication factor integer shift	*/
 #else
-#define PLPRCR_MF_MSK	0xfff00000	/* Multiplication factor bits		*/
-#define PLPRCR_MF_SHIFT 0x00000014	/* Multiplication factor shift value	*/
+#define PLPRCR_MF_MSK	0xFFF00000	/* Multiplication factor bits		*/
+#define PLPRCR_MF_SHIFT		20	/* Multiplication factor shift value	*/
 #endif
 #define PLPRCR_SPLSS	0x00008000	/* SPLL Lock Status Sticky bit		*/
 #define PLPRCR_TEXPS	0x00004000	/* TEXP Status				*/
@@ -166,8 +166,8 @@
 #define PLPRCR_LOLRE	0x00000040	/* Loss Of Lock Reset Enable		*/
 #define PLPRCR_FIOPD	0x00000020	/* Force I/O Pull Down			*/
 #ifdef CONFIG_MPC866_et_al
-#define PLPRCR_PDF_MSK	0x0000001e	/* Predivision Factor bits		*/
-#define PLPRCR_PDF_SHIFT 0x00000001	/* Predivision Factor shift value	*/
+#define PLPRCR_PDF_MSK	0x0000001E	/* Predivision Factor bits		*/
+#define PLPRCR_PDF_SHIFT	 1	/* Predivision Factor shift value	*/
 #define PLPRCR_DBRMO	0x00000001	/* DPLL BRM Order bit			*/
 #endif
 
diff --git a/include/pci_ids.h b/include/pci_ids.h
index a27d31c..a5d7ed5 100644
--- a/include/pci_ids.h
+++ b/include/pci_ids.h
@@ -1543,4 +1543,3 @@
 #define PCI_DEVICE_ID_SMI_710           0x0710
 #define PCI_DEVICE_ID_SMI_712           0x0712
 #define PCI_DEVICE_ID_SMI_810           0x0810
-