Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

6 files changed, 829 insertions, 6 deletions

diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index da6e760..e776a46 100644
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -375,7 +375,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
 
 /* Serial Port - controlled on board with jumper J8
  * open - index 2
@@ -401,6 +401,25 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 
+/* Video */
+#define CONFIG_FSL_DIU_FB
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x180000)
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+/*
+ * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
+ * disable empty flash sector detection, which is I/O-intensive.
+ */
+#undef CONFIG_SYS_FLASH_EMPTY_INFO
+#endif
+
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
@@ -426,6 +445,11 @@ unsigned long get_board_ddr_clk(void);
 
 /* I2C bus multiplexer */
 #define I2C_MUX_CH_DEFAULT      0x8
+#define I2C_MUX_CH_DIU		0xC
+
+/* LDI/DVI Encoder for display */
+#define CONFIG_SYS_I2C_LDI_ADDR         0x38
+#define CONFIG_SYS_I2C_DVI_ADDR         0x75
 
 /*
  * RTC configuration
@@ -703,6 +727,7 @@ unsigned long get_board_ddr_clk(void);
 	"bank_intlv=cs0_cs1;"					\
 	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 	"netdev=eth0\0"						\
+	"video-mode=fslfb:1024x768-32@60,monitor=dvi\0"		\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
 	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
 	"tftpflash=tftpboot $loadaddr $uboot && "		\
diff --git a/include/configs/T1040RDB.h b/include/configs/T1040RDB.h
index fd010c0..395845b 100644
--- a/include/configs/T1040RDB.h
+++ b/include/configs/T1040RDB.h
@@ -147,7 +147,7 @@
 
 /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_DDR_RAW_TIMING
diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h
index 6d07805..68656e6 100644
--- a/include/configs/T1042RDB_PI.h
+++ b/include/configs/T1042RDB_PI.h
@@ -147,7 +147,7 @@
 
 /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_DDR_RAW_TIMING
diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 5b22d64..c6a30db 100644
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -242,7 +242,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
 					FTIM1_GPCM_TRAD(0x3f))
 #define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
-					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TCH(0x8) | \
 					FTIM2_GPCM_TWP(0x1f))
 #define CONFIG_SYS_CS3_FTIM3		0x0
 
diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
new file mode 100644
index 0000000..979843b
--- /dev/null
+++ b/include/configs/T208xRDB.h
@@ -0,0 +1,779 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+/*
+ * T2080 RDB/PCIe board configuration file
+ */
+
+#ifndef __T2080RDB_H
+#define __T2080RDB_H
+
+#define CONFIG_T2080RDB
+#define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
+#define CONFIG_MMC
+#define CONFIG_SPI_FLASH
+#define CONFIG_USB_EHCI
+#define CONFIG_FSL_SATA_V2
+
+/* High Level Configuration Options */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_BOOKE
+#define CONFIG_E500		/* BOOKE e500 family */
+#define CONFIG_E500MC		/* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV	/* Category E.HV supported */
+#define CONFIG_MP		/* support multiple processors */
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC	/* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC	CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC		/* Enable IFC Support */
+#define CONFIG_FSL_LAW		/* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xrdb/t2080_pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xrdb/t2080_rcw.cfg
+#endif
+
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xeff40000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB		/* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+
+#ifdef CONFIG_SYS_NO_FLASH
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS	0
+#define CONFIG_ENV_SPI_CS	0
+#define CONFIG_ENV_SPI_MAX_HZ	10000000
+#define CONFIG_ENV_SPI_MODE	0
+#define CONFIG_ENV_SIZE		0x2000	   /* 8KB */
+#define CONFIG_ENV_OFFSET	0x100000   /* 1MB */
+#define CONFIG_ENV_SECT_SIZE	0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV	0
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_OFFSET	(512 * 1658)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET	(2 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR		0xffe20000
+#define CONFIG_ENV_SIZE		0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE		0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	66660000
+#define CONFIG_DDR_CLK_FREQ	133330000
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR	 CONFIG_RAMBOOT_TEXT_BASE
+
+#define CONFIG_SYS_DCSRBAR	0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS	0xf00000000ull
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define CONFIG_SYS_SDRAM_SIZE	2048	/* for fixed parameter use */
+#define SPD_EEPROM_ADDRESS1	0x51
+#define SPD_EEPROM_ADDRESS2	0x52
+#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
+#define CTRL_INTLV_PREFERED	cacheline
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE		0xe8000000
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
+
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1A) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS }
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE	0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2_EXT	(0xf)
+#define CONFIG_SYS_CSPR2	(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK2	IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2	0x0
+
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
+					FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3		0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	 /* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */	    \
+				| CSOR_NAND_RAL_3	/* RAL = 2Byes */   \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */\
+				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */\
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)    | \
+					FTIM0_NAND_TWCHT(0x07)  | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)   | \
+					FTIM1_NAND_TRR(0x0e)    | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f)  | \
+					FTIM2_NAND_TREH(0x0a)   | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE	 CONFIG_SYS_TEXT_BASE
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+			((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+						GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
+#define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
+#define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
+#define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
+#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
+#define CONFIG_SYS_FSL_I2C_SPEED   100000
+#define CONFIG_SYS_FSL_I2C2_SPEED  100000
+#define CONFIG_SYS_FSL_I2C3_SPEED  100000
+#define CONFIG_SYS_FSL_I2C4_SPEED  100000
+#define I2C_MUX_PCA_ADDR_PRI	0x77 /* I2C bus multiplexer,primary */
+#define I2C_MUX_PCA_ADDR_SEC1	0x75 /* I2C bus multiplexer,secondary 1 */
+#define I2C_MUX_PCA_ADDR_SEC2	0x76 /* I2C bus multiplexer,secondary 2 */
+#define I2C_MUX_CH_DEFAULT	0x8
+
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
+#define CONFIG_SYS_SRIO1_MEM_SIZE	0x10000000 /* 256M */
+#define CONFIG_SYS_SRIO2_MEM_VIRT	0xb0000000
+#define CONFIG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
+#define CONFIG_SYS_SRIO2_MEM_SIZE	0x10000000 /* 256M */
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x80000 /* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000	/* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_BAR
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED	 10000000
+#define CONFIG_SF_DEFAULT_MODE	  0
+#endif
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI		/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		/* PCIE controler 1 */
+#define CONFIG_PCIE2		/* PCIE controler 2 */
+#define CONFIG_PCIE3		/* PCIE controler 3 */
+#define CONFIG_PCIE4		/* PCIE controler 4 */
+#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000      /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc30000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 4, Base address 203000 */
+#define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS	0xc40000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
+#define CONFIG_NET_MULTI
+#define CONFIG_E1000
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	18
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	18
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_DPAA_RMAN		/* RMan */
+#define CONFIG_SYS_INTERLAKEN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_CORTINA_FW_ADDR		0x120000
+
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 825KB (1650 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_CORTINA_FW_ADDR		(512 * 1808)
+
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_CORTINA_FW_ADDR		(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_CORTINA_FW_ADDR		0xFFE10000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_CORTINA_FW_ADDR		0xEFE00000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_CORTINA
+#define CONFIG_PHY_AQ1202
+#define CONFIG_PHY_REALTEK
+#define CONFIG_CORTINA_FW_LENGTH	0x40000
+#define RGMII_PHY1_ADDR		0x01  /* RealTek RTL8211E */
+#define RGMII_PHY2_ADDR		0x02
+#define CORTINA_PHY_ADDR1	0x0c  /* Cortina CS4315 */
+#define CORTINA_PHY_ADDR2	0x0d
+#define FM1_10GEC3_PHY_ADDR	0x00  /* Aquantia AQ1202 10G Base-T */
+#define FM1_10GEC4_PHY_ADDR	0x01
+#endif
+
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC3"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * SATA
+ */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_HAS_FSL_DR_USB
+#endif
+
+/*
+ * SDHC
+ */
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Environment
+ */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_BDI
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT	"=> "	  /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE	1024	  /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256	  /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH	 "/opt/nfsroot"
+#define CONFIG_BOOTFILE	 "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin"	/* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
+#define __USB_PHY_TYPE		utmi
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:"					\
+	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
+	"bank_intlv=auto;"					\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
+	"tftpflash=tftpboot $loadaddr $uboot && "		\
+	"protect off $ubootaddr +$filesize && "			\
+	"erase $ubootaddr +$filesize && "			\
+	"cp.b $loadaddr $ubootaddr $filesize && "		\
+	"protect on $ubootaddr +$filesize && "			\
+	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=t2080rdb/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=t2080rdb/t2080rdb.dtb\0"			\
+	"bdev=sda3\0"						\
+	"c=ffe\0"
+
+/*
+ * For emulation this causes u-boot to jump to the start of the
+ * proof point app code automatically
+ */
+#define CONFIG_PROOF_POINTS				\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"cpu 1 release 0x29000000 - - -;"		\
+	"cpu 2 release 0x29000000 - - -;"		\
+	"cpu 3 release 0x29000000 - - -;"		\
+	"cpu 4 release 0x29000000 - - -;"		\
+	"cpu 5 release 0x29000000 - - -;"		\
+	"cpu 6 release 0x29000000 - - -;"		\
+	"cpu 7 release 0x29000000 - - -;"		\
+	"go 0x29000000"
+
+#define CONFIG_HVBOOT				\
+	"setenv bootargs config-addr=0x60000000; "	\
+	"bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU				\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"cpu 1 release 0x01000000 - - -;"		\
+	"cpu 2 release 0x01000000 - - -;"		\
+	"cpu 3 release 0x01000000 - - -;"		\
+	"cpu 4 release 0x01000000 - - -;"		\
+	"cpu 5 release 0x01000000 - - -;"		\
+	"cpu 6 release 0x01000000 - - -;"		\
+	"cpu 7 release 0x01000000 - - -;"		\
+	"go 0x01000000"
+
+#define CONFIG_LINUX				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"setenv ramdiskaddr 0x02000000;"		\
+	"setenv fdtaddr 0x00c00000;"			\
+	"setenv loadaddr 0x1000000;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT					\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#undef CONFIG_CMD_USB
+#endif
+
+#endif	/* __T2080RDB_H */
diff --git a/include/fsl_usb.h b/include/fsl_usb.h
index 915774c..8b63cdd 100644
--- a/include/fsl_usb.h
+++ b/include/fsl_usb.h
@@ -52,13 +52,32 @@ struct ccsr_usb_phy {
 #define CONFIG_SYS_FSL_USB_PLLPRG2_MFI (5 << 16)
 #define CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN (1 << 21)
 #define CONFIG_SYS_FSL_USB_SYS_CLK_VALID (1 << 0)
+#define CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_EN (1 << 7)
+#define CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_MASK (3 << 4)
+
+#define INC_DCNT_THRESHOLD_25MV        (0 << 4)
+#define INC_DCNT_THRESHOLD_50MV        (1 << 4)
+#define DEC_DCNT_THRESHOLD_25MV        (2 << 4)
+#define DEC_DCNT_THRESHOLD_50MV        (3 << 4)
 #else
 struct ccsr_usb_phy {
-	u8	res0[0x18];
+	u32     config1;
+	u32     config2;
+	u32     config3;
+	u32     config4;
+	u32     config5;
+	u32     status1;
 	u32	usb_enable_override;
 	u8	res[0xe4];
 };
-#define	CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE	1
+#define CONFIG_SYS_FSL_USB_HS_DISCNCT_INC (3 << 22)
+#define CONFIG_SYS_FSL_USB_RX_AUTO_CAL_RD_WR_SEL (1 << 20)
+#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_WR_0 13
+#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_WR_3 16
+#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_RD_0 0
+#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_RD_3 3
+#define CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE 1
+#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_MASK 0x07
 #endif
 
 #endif /*_ASM_FSL_USB_H_ */