powerpc: remove MBX and MBX860T boards support

Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove board/mbx8xx/*
 - Remove include/configs/{MBX.h,MBX860T.h}
 - Clean-up if defined(CONFIG_MBX)
 - Move the entries from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

4 files changed, 0 insertions, 724 deletions

diff --git a/include/common.h b/include/common.h
index cbd3c9e..580615b 100644
--- a/include/common.h
+++ b/include/common.h
@@ -511,13 +511,6 @@ void rpxclassic_init (void);
 
 void rpxlite_init (void);
 
-#ifdef CONFIG_MBX
-/* $(BOARD)/mbx8xx.c */
-void	mbx_init (void);
-void	board_serial_init (void);
-void	board_ether_init (void);
-#endif
-
 #ifdef CONFIG_HERMES
 /* $(BOARD)/hermes.c */
 void hermes_start_lxt980 (int speed);
diff --git a/include/commproc.h b/include/commproc.h
index 12b9421..62468c3 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -12,10 +12,6 @@
  * CPM capabilities.  I (or someone else) will add definitions as they
  * are needed.  -- Dan
  *
- * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
- * bytes of the DP RAM and relocates the I2C parameter area to the
- * IDMA1 space.  The remaining DP RAM is available for buffer descriptors
- * or other use.
  */
 #ifndef __CPM_8XX__
 #define __CPM_8XX__
@@ -135,7 +131,6 @@ typedef struct cpm_buf_desc {
 #define PROFF_SMC2	((uint)0x0380)
 
 /* Define enough so I can at least use the serial port as a UART.
- * The MBX uses SMC1 as the host serial port.
  */
 typedef struct smc_uart {
 	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
@@ -888,33 +883,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00003E00)
 #endif	/* CONFIG_LWMON */
 
-/***  MBX  ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.  The TCLK and RCLK seem unique
- * to the MBX860 board.  Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PC_ENET_TENA	((ushort)0x0001)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-#endif	/* CONFIG_MBX */
-
 /***  KM8XX  *********************************************************/
 
 /* The KM8XX Service Module uses SCC3 for Ethernet */
diff --git a/include/configs/MBX.h b/include/configs/MBX.h
deleted file mode 100644
index 96edd44..0000000
--- a/include/configs/MBX.h
+++ /dev/null
@@ -1,290 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Configuation settings for the MBX8xx board.
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- */
-/*
- * Changed 2002-10-01
- * Added PCMCIA defines mostly taken from other U-Boot boards that
- * have PCMCIA already working.  If you find any bugs, incorrect assumptions
- * feel free to fix them yourself and submit a patch.
- * Rod Boyce <rod_boyce@stratexnet.com.
- */
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
-#define CONFIG_MBX		1	/* ...on an MBX module		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xfe000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-/* Define this to use the PCI bus */
-#undef CONFIG_USE_PCI
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-#define CONFIG_8xx_GCLK_FREQ    (50000000UL)
-#if 1
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-#define CONFIG_BOOTCOMMAND	"bootm 20000" /* autoboot command	*/
-
-#define CONFIG_BOOTARGS		"root=/dev/nfs rw "			\
-				"nfsroot=10.0.0.2:/opt/eldk/ppc_8xx "	\
-				"nfsaddrs=10.0.0.99:10.0.0.2"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE   /* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_IDE
-
-
-#define CONFIG_DOS_PARTITION
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#undef	CONFIG_SYS_HUSH_PARSER			/* Hush parse for U-Boot	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Physical memory map as defined by the MBX PGM
- */
-#define CONFIG_SYS_IMMR		0xFA200000 /* Internal Memory Mapped Register*/
-#define CONFIG_SYS_NVRAM_BASE		0xFA000000 /* NVRAM			     */
-#define CONFIG_SYS_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
-#define CONFIG_SYS_CSR_BASE		0xFA100000 /* Control/Status Registers	     */
-#define CONFIG_SYS_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces	     */
-#define CONFIG_SYS_PCIMEM_OR		0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers	     */
-#define CONFIG_SYS_PCIBRIDGE_OR	0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2f00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD		(CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xfe000000
-#ifdef	DEBUG
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#endif
-#undef	CONFIG_SYS_MONITOR_BASE	/* 0x200000	   to run U-Boot from RAM */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE		0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-/* #define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC11 | SIUMCR_SEME | SIUMCR_BSC )
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR	SCCR_TBS
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-#define CONFIG_SYS_PCMCIA_INTERRUPT	SIU_LEVEL6
-
-#define CONFIG_PCMCIA_SLOT_A	1
-
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- * Debug Entry Mode
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/MBX860T.h b/include/configs/MBX860T.h
deleted file mode 100644
index 74f44df..0000000
--- a/include/configs/MBX860T.h
+++ /dev/null
@@ -1,395 +0,0 @@
- /*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T MBX board.
-  * Copied from the FADS stuff, which was originally copied from the MBX stuff!
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  * Rob Taylor coverted it back to MBX
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#include <mpc8xx_irq.h>
-
-#define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_MBX		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xfe000000
-
-#define CONFIG_8xx_CPUCLOCK	40
-#define CONFIG_8xx_BUSCLOCK	(CONFIG_8xx_CPUCLOCK)
-#define TARGET_SYSTEM_FREQUENCY 40
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#define CONFIG_BAUDRATE		9600
-
-#define MPC8XX_FACT	10				/* Multiply by 10		*/
-#define MPC8XX_XIN	40000000		/* 50 MHz in	*/
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_8xx_BOOTDELAY	-1	/* autoboot disabled		*/
-#define CONFIG_8xx_TFTP_MODE
-#else
-#define CONFIG_8xx_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#undef	CONFIG_8xx_TFTP_MODE
-#endif
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_DRAM_SPEED	(CONFIG_8xx_BUSCLOCK)	/* MHz		*/
-#define CONFIG_BOOTCOMMAND	"bootm FE020000"	/* autoboot command */
-#define CONFIG_BOOTARGS		" "
-/*
- * Miscellaneous configurable options
- */
-#undef	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0800000	/* 4 ... 8 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR			0xFFA00000
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-#define CONFIG_SYS_NVRAM_BASE		0xFA000000 /* NVRAM                          */
-#define CONFIG_SYS_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
-#define CONFIG_SYS_CSR_BASE		0xFA100000 /* Control/Status Registers       */
-#define CONFIG_SYS_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces      */
-#define CONFIG_SYS_PCIMEM_OR		0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers       */
-#define CONFIG_SYS_PCIBRIDGE_OR	0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2f00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD		(CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-/*0xFE000000*/
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_HWINFO_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	4	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE		0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR	SCCR_TBS
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-
-#define BCSR_ADDR		((uint) 0xFF010000)
-#define BCSR_SIZE		((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM	0xFE000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0xFF010000	/* FLASH bank #0	*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFFF00000	/* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM	(0xFE000000 | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	0xFFC00000 | OR_ACS_DIV4
-#define CONFIG_SYS_BR1_PRELIM	(0x00000000 | BR_MS_UPMA | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA		97		/* start with divider for 100 MHz	*/
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR		0x13821000
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR		((uint)0xff020000)
-#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
-
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
-#define	BCSR1			((uint) (BCSR_ADDR + 0x04))
-#define	BCSR2			((uint) (BCSR_ADDR + 0x08))
-#define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
-#define	BCSR4			((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB       ((uint)0x80000000)
-#define BCSR0_IP        ((uint)0x40000000)
-#define BCSR0_BDIS      ((uint)0x10000000)
-#define BCSR0_BPS_MASK  ((uint)0x0C000000)
-#define BCSR0_ISB_MASK  ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN           ((uint)0x80000000)
-#define BCSR1_DRAM_EN            ((uint)0x40000000)
-#define BCSR1_ETHEN              ((uint)0x20000000)
-#define BCSR1_IRDEN              ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN            ((uint)0x02000000)
-#define BCSR1_RS232EN_1          ((uint)0x01000000)
-#define BCSR1_PCCEN              ((uint)0x00800000)
-#define BCSR1_PCCVCC0            ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
-#define BCSR1_RS232EN_2          ((uint)0x00040000)
-#define BCSR1_SDRAM_EN           ((uint)0x00020000)
-#define BCSR1_PCCVCC1            ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT      (23)
-#define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK       ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK          ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0            ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
-#define BCSR3_BREVN1             ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK        ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP            ((uint)0x80000000)
-#define BCSR4_TFPLDL             ((uint)0x40000000)
-#define BCSR4_TPSQEL             ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN             ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#define BCSR4_USB_SPEED          ((uint)0x04000000)
-#define BCSR4_VCCO               ((uint)0x02000000)
-#define BCSR4_VIDEO_ON           ((uint)0x00800000)
-#define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
-#define BCSR4_VIDEO_RST          ((uint)0x00200000)
-#define BCSR4_MODEM_EN           ((uint)0x00100000)
-#define BCSR4_DATA_VOICE         ((uint)0x00080000)
-
-#define CONFIG_DRAM_40MHZ		1
-
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-#define CONFIG_CMD_NET
-/*
- * MPC8xx CPM Options
- */
-#define CONFIG_SCC_ENET 1
-#define CONFIG_SCC1_ENET 1
-#define CONFIG_FEC_ENET 1
-#undef  CONFIG_CPM_IIC
-#undef  CONFIG_UCODE_PATCH
-
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS    2
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#endif	/* __CONFIG_H */