mpc8xx: remove spc1920 board support

This board is old enough and has no maintainer.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

1 files changed, 0 insertions, 405 deletions

diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h
deleted file mode 100644
index 127de00..0000000
--- a/include/configs/spc1920.h
+++ /dev/null
@@ -1,405 +0,0 @@
-/*
- * (C) Copyright 2006
- * Markus Klotzbuecher, DENX Software Engineering, mk@denx.de
- *
- * Configuation settings for the SPC1920 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __H
-#define __CONFIG_H
-
-#define CONFIG_SPC1920			1	/* SPC1920 board */
-#define CONFIG_MPC885			1	/* MPC885 CPU */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-#define	CONFIG_8xx_CONS_SMC1		/* Console is on SMC1 */
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-
-#define CONFIG_MII
-#define CONFIG_MII_INIT		1
-#undef CONFIG_ETHER_ON_FEC1
-#define CONFIG_ETHER_ON_FEC2
-#define FEC_ENET
-#define CONFIG_FEC2_PHY		1
-
-#define CONFIG_BAUDRATE		19200
-
-/* use PLD CLK4 instead of brg */
-#define CONFIG_SYS_SPC1920_SMC1_CLK4
-
-#define CONFIG_8xx_OSCLK		10000000 /* 10 MHz oscillator on EXTCLK  */
-#define CONFIG_8xx_CPUCLK_DEFAULT	50000000
-#define CONFIG_SYS_8xx_CPUCLK_MIN		40000000
-#define CONFIG_SYS_8xx_CPUCLK_MAX		133000000
-
-#define CONFIG_SYS_RESET_ADDRESS		0xC0000000
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_LAST_STAGE_INIT
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_NFSBOOTCOMMAND							\
-    "dhcp;"									\
-    "setenv bootargs root=/dev/nfs rw nfsroot=$rootpath "			\
-    "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;"		\
-    "bootm"
-
-#define CONFIG_BOOTCOMMAND							\
-    "setenv bootargs root=/dev/mtdblock2 rw mtdparts=phys:1280K(ROM)ro,-(root) "\
-    "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;"		\
-    "bootm fe080000"
-
-#undef CONFIG_BOOTARGS
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-#define CONFIG_BZIP2	 /* include support for bzip2 compressed images */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#define CONFIG_SYS_HUSH_PARSER
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size	*/
-#define	CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x00100000
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 2400, 4800, 9600, 19200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 KB for monitor	*/
-
-#ifdef CONFIG_BZIP2
-#define	CONFIG_SYS_MALLOC_LEN		(2500 << 10)	/* Reserve ~2.5 MB for malloc()	*/
-#else
-#define	CONFIG_SYS_MALLOC_LEN		(384 << 10)	/* Reserve 384 kB for malloc()	*/
-#endif /* CONFIG_BZIP2 */
-
-#define	CONFIG_SYS_ALLOC_DPRAM		1	/* use allocation routines	*/
-
-/*
- * Flash
- */
-/*-----------------------------------------------------------------------
- * Flash organisation
- */
-#define CONFIG_SYS_FLASH_BASE          0xFE000000
-#define CONFIG_SYS_FLASH_CFI                           /* The flash is CFI compatible  */
-#define CONFIG_FLASH_CFI_DRIVER                    /* Use common CFI driver        */
-#define CONFIG_SYS_MAX_FLASH_BANKS     1               /* Max number of flash banks    */
-#define CONFIG_SYS_MAX_FLASH_SECT      128             /* Max num of sects on one chip */
-
-/* Environment is in flash */
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE       0x40000         /* We use one complete sector   */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-
-#define CONFIG_ENV_OVERWRITE
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-
-#ifdef CONFIG_CMD_DATE
-# define CONFIG_RTC_DS3231
-# define CONFIG_SYS_I2C_RTC_ADDR      0x68
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C configuration
- */
-#if defined(CONFIG_CMD_I2C)
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL         0x00000020      /* PB 26 */
-#define PB_SDA         0x00000010      /* PB 27 */
-
-#define I2C_INIT       (immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE     (immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE   (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ       ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-		       else    immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-		       else    immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY      udelay(2)       /* 1/4 I2C clock duration */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR      (SIUMCR_FRC)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-/* #define CONFIG_SYS_SCCR	SCCR_TBS */
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * DER - Debug Enable Register
- *-----------------------------------------------------------------------
- * Set to zero to prevent the processor from entering debug mode
- */
-#define CONFIG_SYS_DER		 0
-
-
-/* Because of the way the 860 starts up and assigns CS0 the entire
- * address space, we have to set the memory controller differently.
- * Normally, you write the option register first, and then enable the
- * chip select by writing the base register.  For CS0, you must write
- * the base register first, followed by the option register.
- */
-
-
-/*
- * Init Memory Controller:
- */
-
-/* BR0 and OR0 (FLASH) */
-#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0 */
-
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_6_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-
-/*
- * SDRAM CS1 UPMB
- */
-#define	CONFIG_SYS_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE_PRELIM CONFIG_SYS_SDRAM_BASE
-#define SDRAM_MAX_SIZE	0x4000000 /* max 64 MB */
-
-#define CONFIG_SYS_PRELIM_OR1_AM	0xF0000000
-/* #define CONFIG_SYS_OR1_TIMING  OR_CSNT_SAM/\*  | OR_G5LS /\\* *\\/ *\/ */
-#define SDRAM_TIMING	OR_SCY_0_CLK	/* SDRAM-Timing */
-
-#define CONFIG_SYS_OR1_PRELIM	(CONFIG_SYS_PRELIM_OR1_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING)
-#define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V)
-
-/* #define CONFIG_SYS_OR1_FINAL   ((CONFIG_SYS_OR1_AM & OR_AM_MSK) | CONFIG_SYS_OR1_TIMING) */
-/* #define CONFIG_SYS_BR1_FINAL   ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V) */
-
-#define CONFIG_SYS_PTB_PER_CLK	((4096 * 16 * 1000) / (4 * 64))
-#define CONFIG_SYS_PTA_PER_CLK 195
-#define CONFIG_SYS_MBMR_PTB	195
-#define CONFIG_SYS_MPTPR	MPTPR_PTP_DIV16
-#define CONFIG_SYS_MAR		0x88
-
-#define CONFIG_SYS_MBMR_8COL  ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \
-			MBMR_AMB_TYPE_0 | \
-			MBMR_G0CLB_A10 | \
-			MBMR_DSB_1_CYCL | \
-			MBMR_RLFB_1X | \
-			MBMR_WLFB_1X | \
-			MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */
-
-#define CONFIG_SYS_MBMR_9COL  ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \
-			MBMR_AMB_TYPE_1 | \
-			MBMR_G0CLB_A10 | \
-			MBMR_DSB_1_CYCL | \
-			MBMR_RLFB_1X | \
-			MBMR_WLFB_1X | \
-			MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */
-
-
-/*
- * DSP Host Port Interface CS3
- */
-#define CONFIG_SYS_SPC1920_HPI_BASE   0x90000000
-#define CONFIG_SYS_PRELIM_OR3_AM      0xF8000000
-
-#define CONFIG_SYS_OR3         (CONFIG_SYS_PRELIM_OR3_AM | \
-				       OR_G5LS | \
-				       OR_SCY_0_CLK | \
-				       OR_BI)
-
-#define CONFIG_SYS_BR3 ((CONFIG_SYS_SPC1920_HPI_BASE & BR_BA_MSK) | \
-					       BR_MS_UPMA | \
-					       BR_PS_16 | \
-					       BR_V)
-
-#define CONFIG_SYS_MAMR (MAMR_GPL_A4DIS | \
-		MAMR_RLFA_5X | \
-		MAMR_WLFA_5X)
-
-#define CONFIG_SPC1920_HPI_TEST
-
-#ifdef CONFIG_SPC1920_HPI_TEST
-#define HPI_REG(x)             (*((volatile u16 *) (CONFIG_SYS_SPC1920_HPI_BASE + x)))
-#define HPI_HPIC_1             HPI_REG(0)
-#define HPI_HPIC_2             HPI_REG(2)
-#define HPI_HPIA_1             HPI_REG(0x2000008)
-#define HPI_HPIA_2             HPI_REG(0x2000008 + 2)
-#define HPI_HPID_INC_1         HPI_REG(0x1000004)
-#define HPI_HPID_INC_2         HPI_REG(0x1000004 + 2)
-#define HPI_HPID_NOINC_1       HPI_REG(0x300000c)
-#define HPI_HPID_NOINC_2       HPI_REG(0x300000c + 2)
-#endif /* CONFIG_SPC1920_HPI_TEST */
-
-/*
- * Ramtron FM18L08 FRAM 32KB on CS4
- */
-#define CONFIG_SYS_SPC1920_FRAM_BASE	0x80100000
-#define CONFIG_SYS_PRELIM_OR4_AM	0xffff8000
-#define CONFIG_SYS_OR4		(CONFIG_SYS_PRELIM_OR4_AM | \
-					OR_ACS_DIV2 | \
-					OR_BI | \
-					OR_SCY_4_CLK | \
-					OR_TRLX)
-
-#define CONFIG_SYS_BR4 ((CONFIG_SYS_SPC1920_FRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
-
-/*
- * PLD CS5
- */
-#define CONFIG_SYS_SPC1920_PLD_BASE	0x80000000
-#define CONFIG_SYS_PRELIM_OR5_AM	0xffff8000
-
-#define CONFIG_SYS_OR5_PRELIM		(CONFIG_SYS_PRELIM_OR5_AM | \
-					OR_CSNT_SAM | \
-					OR_ACS_DIV1 | \
-					OR_BI | \
-					OR_SCY_0_CLK | \
-					OR_TRLX)
-
-#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_SPC1920_PLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
-
-#endif	/* __CONFIG_H */