powerpc: remove rsdproto board support

Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/rsdproto/*
 - Remove include/configs/rsdproto.h
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

1 files changed, 0 insertions, 400 deletions

diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h
deleted file mode 100644
index 0621138..0000000
--- a/include/configs/rsdproto.h
+++ /dev/null
@@ -1,400 +0,0 @@
-/*
- * (C) Copyright 2000
- * Murray Jensen <Murray.Jensen@cmst.csiro.au>
- *
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Configuation settings for the R&S Protocol Board board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_RSD_PROTO	1	/* on a R&S Protocol Board      */
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define	CONFIG_SYS_TEXT_BASE	0xff000000
-#define	CONFIG_SYS_LDSCRIPT	"board/rsdproto/u-boot.lds"
-
-#define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#undef	CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#define	CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef	CONFIG_CONS_NONE		/* define if console on neither */
-#define CONFIG_CONS_INDEX	1	/* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ethernet on SCC	*/
-#define	CONFIG_ETHER_ON_FCC		/* define if ethernet on FCC	*/
-#undef	CONFIG_ETHER_NONE		/* define if ethernet on neither */
-#define CONFIG_ETHER_INDEX	2	/* which SCC/FCC channel for ethernet */
-
-#if (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	(0)
-# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_INDEX */
-
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* enable I2C */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x30
-
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#define CONFIG_8260_CLKIN	50000000	/* in Hz */
-
-#define CONFIG_BAUDRATE		115200
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#undef CONFIG_CMD_KGDB
-
-
-/* Define this if you want to boot from 0x00000100. If you don't define
- * this, you will need to program the bootloader to 0xfff00000, and
- * get the hardware reset config words at 0xfe000000. The simplest
- * way to do that is to program the bootloader at both addresses.
- * It is suggested that you just let U-Boot live at 0x00000000.
- */
-#define CONFIG_SYS_RSD_BOOT_LOW 1
-
-#define CONFIG_BOOTDELAY	5
-#define CONFIG_BOOTARGS		"devfs=mount root=ramfs"
-#define CONFIG_ETHADDR		08:00:3e:26:0a:5a
-#define CONFIG_NETMASK          255.255.0.0
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x01c00000	/* 4 ... 28 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define PHYS_SDRAM_60X		0x00000000 /* SDRAM (60x Bus) */
-#define PHYS_SDRAM_60X_SIZE	0x08000000 /* 128 MB */
-
-#define PHYS_SDRAM_LOCAL	0x40000000 /* SDRAM (Local Bus) */
-#define PHYS_SDRAM_LOCAL_SIZE	0x04000000 /* 64 MB */
-
-#define PHYS_DPRAM_PCI		0xE8000000 /* DPRAM PPC/PCI */
-#define PHYS_DPRAM_PCI_SIZE	0x00020000 /* 128 KB */
-
-/*#define PHYS_DPRAM_PCI_SEM	0x04020000 / * DPRAM PPC/PCI Semaphore */
-/*#define PHYS_DPRAM_PCI_SEM_SIZE	0x00000001 / * 1 Byte */
-
-#define PHYS_DPRAM_SHARC	0xE8100000 /* DPRAM PPC/Sharc */
-#define PHYS_DPRAM_SHARC_SIZE	0x00040000 /* 256 KB */
-
-/*#define PHYS_DPRAM_SHARC_SEM	0x04140000 / * DPRAM PPC/Sharc Semaphore */
-/*#define PHYS_DPRAM_SHARC_SEM_SIZE 0x00000001 / * 1 Byte */
-
-#define PHYS_VIRTEX_REGISTER    0xE8300000 /* FPGA implemented register */
-#define PHYS_VIRTEX_REGISTER_SIZE 0x00000100
-
-#define PHYS_USB		0x04200000 /* USB Controller (60x Bus) */
-#define PHYS_USB_SIZE		0x00000002 /* 2 Bytes */
-
-#define PHYS_IMMR		0xF0000000 /* Internal Memory Mapped Reg. */
-
-#define PHYS_FLASH		0xFF000000 /* Flash (60x Bus) */
-#define PHYS_FLASH_SIZE		0x01000000 /* 16 MB */
-
-#define CONFIG_SYS_IMMR		PHYS_IMMR
-
-/*-----------------------------------------------------------------------
- * Reset Address
- *
- * In order to reset the CPU, U-Boot jumps to a special address which
- * causes a machine check exception. The default address for this is
- * CONFIG_SYS_MONITOR_BASE - sizeof (ulong), which might not always work, eg. when
- * testing the monitor in RAM using a JTAG debugger.
- *
- * Just set CONFIG_SYS_RESET_ADDRESS to an address that you know is sure to
- * cause a bus error on your hardware.
- */
-#define CONFIG_SYS_RESET_ADDRESS	0x20000000
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-
-#if defined(CONFIG_SYS_RSD_BOOT_LOW)
-#  define  CONFIG_SYS_RSD_HRCW_BOOT_FLAGS  (HRCW_CIP | HRCW_BMS)
-#else
-#  define  CONFIG_SYS_RSD_HRCW_BOOT_FLAGS  (0)
-#endif /* defined(CONFIG_SYS_RSD_BOOT_LOW) */
-
-/* get the HRCW ISB field from CONFIG_SYS_IMMR */
-#define CONFIG_SYS_RSD_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\
-			    ((CONFIG_SYS_IMMR & 0x01000000) >> 7)  |\
-			    ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER	(HRCW_L2CPC10 | \
-			 HRCW_DPPC11 | \
-			 CONFIG_SYS_RSD_HRCW_IMMR |\
-			 HRCW_MMR00 | \
-			 HRCW_APPC10 | \
-			 HRCW_CS10PC00 | \
-			 HRCW_MODCK_H0000 |\
-			 CONFIG_SYS_RSD_HRCW_BOOT_FLAGS)
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1	0
-#define CONFIG_SYS_HRCW_SLAVE2	0
-#define CONFIG_SYS_HRCW_SLAVE3	0
-#define CONFIG_SYS_HRCW_SLAVE4	0
-#define CONFIG_SYS_HRCW_SLAVE5	0
-#define CONFIG_SYS_HRCW_SLAVE6	0
-#define CONFIG_SYS_HRCW_SLAVE7	0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependend.
- */
-#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_60X
-#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH
-/*#define	CONFIG_SYS_MONITOR_BASE	0x200000 */
-#define	CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_RAMBOOT
-#endif
-#define	CONFIG_SYS_MONITOR_LEN		(160 << 10)	/* Reserve 160 kB for Monitor	*/
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	63	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	12000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	3000	/* Timeout for Flash Write (in ms)	*/
-
-/* turn off NVRAM env feature */
-#undef CONFIG_NVRAM_ENV
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR	(PHYS_FLASH + 0x28000)	/* Addr of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x8000	/* Total Size of Environment Sector	*/
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPU			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers			 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT	(HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL	(HID0_ICE|HID0_IFEM|HID0_ABE|HID0_EMCP)
-#define CONFIG_SYS_HID2	0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR		0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration					 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR		0x100c0000
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				 4-31
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DPPC11 | SIUMCR_L2CPC10 | SIUMCR_APPC10 | \
-					 SIUMCR_CS10PC01 | SIUMCR_BCTLC01)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_PBME | SYPCR_LBME | \
-			 SYPCR_SWRI | SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control			 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC	(TMCNTSC_SEC | TMCNTSC_ALR | TMCNTSC_TCF | TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control					 9-8
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SCCR	0x00000000
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration				13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR	0
-
-/*
- * Init Memory Controller:
- */
-
-#define CONFIG_SYS_PSDMR	0x494D2452
-#define CONFIG_SYS_LSDMR	0x49492552
-
-/* Flash */
-#define CONFIG_SYS_BR0_PRELIM	(PHYS_FLASH | BRx_V)
-#define CONFIG_SYS_OR0_PRELIM	(P2SZ_TO_AM(PHYS_FLASH_SIZE) | \
-			 ORxG_BCTLD | \
-			 ORxG_SCY_5_CLK)
-
-/* DPRAM to the PCI BUS on the protocol board */
-#define CONFIG_SYS_BR1_PRELIM	(PHYS_DPRAM_PCI | BRx_V)
-#define CONFIG_SYS_OR1_PRELIM	(P2SZ_TO_AM(PHYS_DPRAM_PCI_SIZE) | \
-			 ORxG_ACS_DIV4)
-
-/* 60x Bus SDRAM */
-#define CONFIG_SYS_BR2_PRELIM	(PHYS_SDRAM_60X | BRx_MS_SDRAM_P | BRx_V)
-#define CONFIG_SYS_OR2_PRELIM	(ORxS_SIZE_TO_AM(PHYS_SDRAM_60X_SIZE) | \
-			 ORxS_BPD_4 | \
-			 ORxS_ROWST_PBI1_A2 | \
-			 ORxS_NUMR_13 | \
-			 ORxS_IBID)
-
-/* Virtex-FPGA - Register */
-#define CONFIG_SYS_BR3_PRELIM  (PHYS_VIRTEX_REGISTER | BRx_V)
-#define CONFIG_SYS_OR3_PRELIM  (ORxS_SIZE_TO_AM(PHYS_VIRTEX_REGISTER_SIZE) | \
-			 ORxG_SCY_1_CLK | \
-			 ORxG_ACS_DIV2 | \
-			 ORxG_CSNT )
-
-/* local bus SDRAM */
-#define CONFIG_SYS_BR4_PRELIM	(PHYS_SDRAM_LOCAL | BRx_PS_32 | BRx_MS_SDRAM_L | BRx_V)
-#define CONFIG_SYS_OR4_PRELIM	(ORxS_SIZE_TO_AM(PHYS_SDRAM_LOCAL_SIZE) | \
-			 ORxS_BPD_4 | \
-			 ORxS_ROWST_PBI1_A4 | \
-			 ORxS_NUMR_13)
-
-/* DPRAM to the Sharc-Bus on the protocol board */
-#define CONFIG_SYS_BR5_PRELIM	(PHYS_DPRAM_SHARC | BRx_V)
-#define CONFIG_SYS_OR5_PRELIM	(P2SZ_TO_AM(PHYS_DPRAM_SHARC_SIZE) | \
-			 ORxG_ACS_DIV4)
-
-#endif	/* __CONFIG_H */