powerpc: manroland: remove uc100, uc101, mucmc52, hmi1001 support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>

5 files changed, 0 insertions, 1052 deletions

diff --git a/include/configs/hmi1001.h b/include/configs/hmi1001.h
deleted file mode 100644
index a1a88b5..0000000
--- a/include/configs/hmi1001.h
+++ /dev/null
@@ -1,339 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200		1	/* This is an MPC5200 CPU	*/
-#define CONFIG_HMI1001		1	/* HMI1001 board		*/
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz		*/
-
-#define CONFIG_BOARD_EARLY_INIT_R
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported			*/
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1	*/
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps	*/
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-#define CONFIG_DOS_PARTITION
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DISPLAY
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SNTP
-
-
-#define	CONFIG_TIMESTAMP	1	/* Print image info with timestamp */
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
-#   define CONFIG_SYS_LOWBOOT		1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_82xx\0"					\
-	""
-
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-#define CONFIG_MISC_INIT_R	1
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x58
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE		0xFF800000
-
-#define CONFIG_SYS_FLASH_SIZE		0x00800000 /* 8 MByte */
-#define CONFIG_SYS_MAX_FLASH_SECT	67	/* max num of sects on one chip */
-
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks
-					   (= chip selects) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SIZE		0x4000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_OFFSET_REDUND   (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND     (CONFIG_ENV_SIZE)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR		0xF0000000
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
-#define CONFIG_SYS_DISPLAY_BASE	0x80600000
-#define CONFIG_SYS_STATUS1_BASE	0x80600200
-#define CONFIG_SYS_STATUS2_BASE	0x80600300
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_DDR	 1
-#define SDRAM_MODE      0x018D0000
-#define SDRAM_EMODE     0x40090000
-#define SDRAM_CONTROL   0x714f0f00
-#define SDRAM_CONFIG1   0x73722930
-#define SDRAM_CONFIG2   0x47770000
-#define SDRAM_TAPDELAY  0x10000000
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
-
-#ifdef CONFIG_POST
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_POST_SIZE
-#else
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE
-#endif
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC	1
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR		0x00
-#define CONFIG_MII		1		/* MII PHY management		*/
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG	0x01051004
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/* Enable an alternate, more extensive memory test */
-#define CONFIG_SYS_ALT_MEMTEST
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL		HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG		0x0004FB00
-#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
-
-/* 8Mbit SRAM @0x80100000 */
-#define CONFIG_SYS_CS1_START		0x80100000
-#define CONFIG_SYS_CS1_SIZE		0x00100000
-#define CONFIG_SYS_CS1_CFG		0x19B00
-
-/* FRAM 32Kbyte @0x80700000 */
-#define CONFIG_SYS_CS2_START		0x80700000
-#define CONFIG_SYS_CS2_SIZE		0x00008000
-#define CONFIG_SYS_CS2_CFG		0x19800
-
-/* Display H1, Status Inputs, EPLD @0x80600000 */
-#define CONFIG_SYS_CS3_START		0x80600000
-#define CONFIG_SYS_CS3_SIZE		0x00100000
-#define CONFIG_SYS_CS3_CFG		0x00019800
-
-#define CONFIG_SYS_CS_BURST		0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE	0x33333333
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef  CONFIG_IDE_8xx_PCCARD		/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
-
-#define CONFIG_IDE_PREINIT	1
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)
-
-/* Interval between registers                                                */
-#define CONFIG_SYS_ATA_STRIDE          4
-
-#define CONFIG_ATAPI            1
-
-#define CONFIG_VIDEO_SMI_LYNXEM
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_LOGO
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define CONFIG_PCI		1
-#define CONFIG_PCI_PNP		1
-#define CONFIG_PCI_SCAN_SHOW	1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
-
-#define CONFIG_PCI_MEM_BUS	0x40000000
-#define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE	0x10000000
-
-#define CONFIG_PCI_IO_BUS	0x50000000
-#define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE	0x01000000
-
-#define CONFIG_SYS_ISA_IO		CONFIG_PCI_IO_BUS
-
-/*---------------------------------------------------------------------*/
-/* Display addresses						       */
-/*---------------------------------------------------------------------*/
-
-#define CONFIG_PDSP188x
-#define CONFIG_SYS_DISP_CHR_RAM	(CONFIG_SYS_DISPLAY_BASE + 0x38)
-#define CONFIG_SYS_DISP_CWORD		(CONFIG_SYS_DISPLAY_BASE + 0x30)
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/mucmc52.h b/include/configs/mucmc52.h
deleted file mode 100644
index ff75ead..0000000
--- a/include/configs/mucmc52.h
+++ /dev/null
@@ -1,126 +0,0 @@
-/*
- * (C) Copyright 2008-2009
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define	CONFIG_MUCMC52		1	/* MUCMC52 board	*/
-#define	CONFIG_HOSTNAME		mucmc52
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xFFF00000
-#endif
-
-#include "manroland/common.h"
-#include "manroland/mpc5200-common.h"
-
-#define	CONFIG_LAST_STAGE_INIT
-/*
- * Serial console configuration
- */
-#define	CONFIG_BAUDRATE		38400	/* ... at 38400 bps	*/
-
-#define	CONFIG_CMD_PCI
-
-/*
- * Flash configuration
- */
-#define	CONFIG_SYS_MAX_FLASH_SECT	67
-
-/*
- * Environment settings
- */
-#define	CONFIG_ENV_SECT_SIZE	0x20000
-
-/*
- * Memory map
- */
-#define	CONFIG_SYS_STATUS1_BASE	0x80600200
-#define	CONFIG_SYS_STATUS2_BASE	0x80600300
-#define	CONFIG_SYS_PMI_UNI_BASE	0x80800000
-#define	CONFIG_SYS_PMI_BROAD_BASE	0x80810000
-
-/*
- * GPIO configuration
- */
-#define	CONFIG_SYS_GPS_PORT_CONFIG	0x8D550644
-
-#define	CONFIG_SYS_MEMTEST_START	0x00100000
-#define	CONFIG_SYS_MEMTEST_END		0x00f00000
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000
-
-#define	CONFIG_SYS_BOOTCS_CFG		0x0004FB00
-
-/* 8Mbit SRAM @0x80100000 */
-#define	CONFIG_SYS_CS1_SIZE		0x00100000
-#define	CONFIG_SYS_CS1_CFG		0x00019B00
-
-#define CONFIG_SYS_SRAM_SIZE		CONFIG_SYS_CS1_SIZE
-
-/* FRAM 32Kbyte @0x80700000 */
-#define	CONFIG_SYS_CS2_START		0x80700000
-#define	CONFIG_SYS_CS2_SIZE		0x00008000
-#define	CONFIG_SYS_CS2_CFG		0x00019800
-
-/* Display H1, Status Inputs, EPLD @0x80600000 */
-#define	CONFIG_SYS_CS3_START		0x80600000
-#define	CONFIG_SYS_CS3_SIZE		0x00100000
-#define	CONFIG_SYS_CS3_CFG		0x00019800
-
-/* PMI Unicast 32Kbyte @0x80800000 */
-#define	CONFIG_SYS_CS6_START		CONFIG_SYS_PMI_UNI_BASE
-#define	CONFIG_SYS_CS6_SIZE		0x00008000
-#define	CONFIG_SYS_CS6_CFG		0xFFFFF930
-
-/* PMI Broadcast 32Kbyte @0x80810000 */
-#define	CONFIG_SYS_CS7_START		CONFIG_SYS_PMI_BROAD_BASE
-#define	CONFIG_SYS_CS7_SIZE		0x00008000
-#define	CONFIG_SYS_CS7_CFG		0xFF00F930
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-#define	CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 2 drives per IDE bus	*/
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define	CONFIG_PCI		1
-#define	CONFIG_PCI_PNP		1
-#define	CONFIG_PCI_SCAN_SHOW	1
-#define	CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
-
-#define	CONFIG_PCI_MEM_BUS	0x40000000
-#define	CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
-#define	CONFIG_PCI_MEM_SIZE	0x10000000
-
-#define	CONFIG_PCI_IO_BUS	0x50000000
-#define	CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
-#define	CONFIG_PCI_IO_SIZE	0x01000000
-
-#define	CONFIG_SYS_ISA_IO		CONFIG_PCI_IO_BUS
-
-/*---------------------------------------------------------------------*/
-/* Display addresses						       */
-/*---------------------------------------------------------------------*/
-
-#define	CONFIG_SYS_DISP_CHR_RAM	(CONFIG_SYS_DISPLAY_BASE + 0x38)
-#define	CONFIG_SYS_DISP_CWORD		(CONFIG_SYS_DISPLAY_BASE + 0x30)
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/uc100.h b/include/configs/uc100.h
deleted file mode 100644
index cad897f..0000000
--- a/include/configs/uc100.h
+++ /dev/null
@@ -1,482 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_MPC862		1       /* enable 862 since the         */
-#define CONFIG_MPC857		1       /* 857 is a variant of the 862  */
-
-#define CONFIG_UC100		1	/* ...on a UC100 module	        */
-
-#define	CONFIG_SYS_TEXT_BASE	0x40700000
-
-#define MPC8XX_FACT		4		/* Multiply by 4	*/
-#define MPC8XX_XIN		25000000	/* 25.0 MHz in		*/
-#define CONFIG_8xx_GCLK_FREQ	(MPC8XX_FACT * MPC8XX_XIN)
-				    /* define if cant' use get_gclk_freq */
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-
-#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/uc100/uImage\0"				\
-	"kernel_addr=40000000\0"					\
-	"ramdisk_addr=40100000\0"					\
-	"load=tftp 100000 /tftpboot/uc100/u-boot.bin\0"			\
-	"update=protect off 40700000 4073ffff;era 40700000 4073ffff;"	\
-		"cp.b 100000 40700000 ${filesize};"			\
-		"setenv filesize;saveenv\0"				\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#undef CONFIG_STATUS_LED                /* no status-led                */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_RTC_MPC8xx
-#define CONFIG_SYS_I2C_RTC_ADDR	0x51	/* PCF8563 RTC			*/
-#define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
-
-/*
- * Power On Self Test support
- */
-#define CONFIG_POST	      ( CONFIG_SYS_POST_CACHE		| \
-				CONFIG_SYS_POST_MEMORY		| \
-				CONFIG_SYS_POST_CPU		| \
-				CONFIG_SYS_POST_UART		| \
-				CONFIG_SYS_POST_SPR )
-#undef  CONFIG_POST
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SNTP
-
-#ifdef CONFIG_POST
-#define CONFIG_CMD_DIAG
-#endif
-
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#if 0
-#define	CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE+0x00700000) /* resetvec fff00100*/
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*-----------------------------------------------------------------------
- * Address accessed to reset the board - must not be mapped/assigned
- */
-#define CONFIG_SYS_RESET_ADDRESS       0x90000000
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_CFI				/* The flash is CFI compatible  */
-#define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver        */
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET	1		/* AMD RESET for STM 29W320DB!  */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector		*/
-#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_FRC | SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR	(((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) |	\
-				PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	0x00000000
-#define CONFIG_SYS_SCCR        (SCCR_EBDF11)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFF800000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(0x00000d24)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_BR1_PRELIM  0x00000081  /* Chip select for SDRAM (32 Bit, UPMA) */
-#define CONFIG_SYS_OR1_PRELIM  0xfc000a00
-#define CONFIG_SYS_BR2_PRELIM  0x80000001  /* Chip select for SRAM (32 Bit, GPCM) */
-#define CONFIG_SYS_OR2_PRELIM  0xfff00d24
-#define CONFIG_SYS_BR3_PRELIM  0x80600401  /* Chip select for Display (8 Bit, GPCM) */
-#define CONFIG_SYS_OR3_PRELIM  0xffff8f44
-#define CONFIG_SYS_BR4_PRELIM  0xc05108c1  /* Chip select for Interbus MPM (16 Bit, UPMB) */
-#define CONFIG_SYS_OR4_PRELIM  0xffff0300
-#define CONFIG_SYS_BR5_PRELIM  0xc0500401  /* Chip select for Interbus Status (8 Bit, GPCM) */
-#define CONFIG_SYS_OR5_PRELIM  0xffff8db0
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- *  50 MHz =>  50.000.000 / Divider =  98
- *  66 Mhz =>  66.000.000 / Divider = 129
- *  80 Mhz =>  80.000.000 / Divider = 156
- * 100 Mhz => 100.000.000 / Divider = 195
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define	CONFIG_SYS_MAMR_VAL	0x30904114	/* for SDRAM */
-#define	CONFIG_SYS_MBMR_VAL	0xff001111	/* for Interbus-MPM */
-
-/*-----------------------------------------------------------------------
- * I2C stuff
- */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	93000 /* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (24C164)
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x58	/* EEPROM AT24C164		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* takes up to 10 msec	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-
-#define	CONFIG_FEC_ENET		1	/* use FEC ethernet  */
-#define FEC_ENET
-#define CONFIG_MII
-#define CONFIG_MII_INIT		1
-#define CONFIG_SYS_DISCOVER_PHY	1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/uc101.h b/include/configs/uc101.h
deleted file mode 100644
index f93dea7..0000000
--- a/include/configs/uc101.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * (C) Copyright 2003-2009
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_UC101		1	/* UC101 board		*/
-#define CONFIG_HOSTNAME		uc101
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xFFF00000
-#endif
-#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc5xxx/u-boot-customlayout.lds"
-
-#include "manroland/common.h"
-#include "manroland/mpc5200-common.h"
-
-/*
- * Serial console configuration
- */
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_MAX_FLASH_SECT	140
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_SECT_SIZE	0x10000
-
-/*
- * Memory map
- */
-#define	CONFIG_SYS_IB_MASTER		0xc0510000	/* CS 6 */
-#define CONFIG_SYS_IB_EPLD		0xc0500000	/* CS 7 */
-
-/* SRAM */
-#define CONFIG_SYS_SRAM_SIZE	0x200000
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG	0x4d558044
-
-#define CONFIG_SYS_MEMTEST_START	0x00300000
-#define CONFIG_SYS_MEMTEST_END		0x00f00000
-
-#define CONFIG_SYS_LOAD_ADDR		0x300000
-
-#define CONFIG_SYS_BOOTCS_CFG		0x00045D00
-
-/* 8Mbit SRAM @0x80100000 */
-#define CONFIG_SYS_CS1_SIZE		0x00200000
-#define CONFIG_SYS_CS1_CFG		0x21D00
-
-/* Display H1, Status Inputs, EPLD @0x80600000 8 Bit */
-#define CONFIG_SYS_CS3_START		CONFIG_SYS_DISPLAY_BASE
-#define CONFIG_SYS_CS3_SIZE		0x00000100
-#define CONFIG_SYS_CS3_CFG		0x00081802
-
-/* Interbus Master 16 Bit */
-#define CONFIG_SYS_CS6_START		CONFIG_SYS_IB_MASTER
-#define CONFIG_SYS_CS6_SIZE		0x00010000
-#define CONFIG_SYS_CS6_CFG		0x00FF3500
-
-/* Interbus EPLD 8 Bit */
-#define CONFIG_SYS_CS7_START		CONFIG_SYS_IB_EPLD
-#define CONFIG_SYS_CS7_SIZE		0x00010000
-#define CONFIG_SYS_CS7_CFG		0x00081800
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 2 drives per IDE bus*/
-
-/*---------------------------------------------------------------------*/
-/* Display addresses						       */
-/*---------------------------------------------------------------------*/
-#define CONFIG_SYS_DISP_CHR_RAM	(CONFIG_SYS_DISPLAY_BASE + 0x38)
-#define CONFIG_SYS_DISP_CWORD		(CONFIG_SYS_DISPLAY_BASE + 0x30)
-
-#endif /* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 00065b2..2ff399b 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -33,8 +33,6 @@
 # define CONFIG_PCMCIA_SLOT_B
 #elif defined(CONFIG_ATC)		/* The ATC use SLOT_A	*/
 # define CONFIG_PCMCIA_SLOT_A
-#elif defined(CONFIG_UC100)		/* The UC100 use SLOT_B	        */
-# define CONFIG_PCMCIA_SLOT_B
 #else
 # error "PCMCIA Slot not configured"
 #endif