mpc8xx: remove netta, netta2, netphone board support

These boards are old enough and have no maintainers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

5 files changed, 0 insertions, 2026 deletions

diff --git a/include/configs/NETPHONE.h b/include/configs/NETPHONE.h
deleted file mode 100644
index 08cfc9e..0000000
--- a/include/configs/NETPHONE.h
+++ /dev/null
@@ -1,701 +0,0 @@
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Pantelis Antoniou, Intracom S.A., panto@intracom.gr
- * U-Boot port on NetTA4 board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#if !defined(CONFIG_NETPHONE_VERSION) || CONFIG_NETPHONE_VERSION > 2
-#error Unsupported CONFIG_NETPHONE version
-#endif
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC870		1	/* This is a MPC885 CPU		*/
-#define CONFIG_NETPHONE		1	/* ...on a NetPhone board	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-/* #define CONFIG_XIN		 10000000 */
-#define CONFIG_XIN		 50000000
-/* #define MPC8XX_HZ		120000000 */
-#define MPC8XX_HZ		 66666666
-
-#define CONFIG_8xx_GCLK_FREQ	MPC8XX_HZ
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#undef	CONFIG_CLOCKS_IN_MHZ	/* clocks NOT passsed to Linux in MHz */
-
-#define CONFIG_PREBOOT	"echo;"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"tftpboot; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"	\
-	"bootm"
-
-#define CONFIG_SOURCE
-#define CONFIG_LOADS_ECHO	0	/* echo off for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-#define CONFIG_BOARD_SPECIFIC_LED	/* version has board specific leds */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_NISDOMAIN
-
-#undef CONFIG_MAC_PARTITION
-#undef CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-#define	FEC_ENET		1	/* eth.c needs it that way... */
-#undef CONFIG_SYS_DISCOVER_PHY
-#define CONFIG_MII		1
-#define CONFIG_MII_INIT		1
-#define CONFIG_RMII		1	/* use RMII interface */
-
-#define CONFIG_ETHER_ON_FEC1	1
-#define CONFIG_FEC1_PHY		8	/* phy address of FEC */
-#define CONFIG_FEC1_PHY_NORXERR 1
-
-#define CONFIG_ETHER_ON_FEC2	1
-#define CONFIG_FEC2_PHY		4
-#define CONFIG_FEC2_PHY_NORXERR 1
-
-#define CONFIG_ENV_OVERWRITE	1	/* allow modification of vendor params */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_CDP
-
-
-#define CONFIG_BOARD_EARLY_INIT_F	1
-#define CONFIG_MISC_INIT_R
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_SYS_HUSH_PARSER	1
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0300000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0700000	/* 3 ... 7 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x3000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#if defined(DEBUG)
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-#if CONFIG_NETPHONE_VERSION == 2
-#define CONFIG_SYS_FLASH_BASE4		0x40080000
-#endif
-
-#define CONFIG_SYS_RESET_ADDRESS   0x80000000
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#if CONFIG_NETPHONE_VERSION == 1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#elif CONFIG_NETPHONE_VERSION == 2
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#endif
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SECT_SIZE	0x10000
-
-#define	CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x60000)
-#define	CONFIG_ENV_SIZE		0x4000
-
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_SYS_FLASH_BASE + 0x70000)
-#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- */
-
-#if CONFIG_XIN == 10000000
-
-#if MPC8XX_HZ == 120000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 100000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 50000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 25000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 40000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 75000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#else
-#error unsupported CPU freq for XIN = 10MHz
-#endif
-
-#elif CONFIG_XIN == 50000000
-
-#if MPC8XX_HZ == 120000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 100000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ ==  66666666
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#else
-#error unsupported CPU freq for XIN = 50MHz
-#endif
-
-#else
-
-#error unsupported XIN freq
-#endif
-
-
-/*
- *-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- *
- * Note: When TBS == 0 the timebase is independent of current cpu clock.
- */
-
-#define SCCR_MASK	SCCR_EBDF11
-#if MPC8XX_HZ > 66666666
-#define CONFIG_SYS_SCCR	(/* SCCR_TBS	| */ SCCR_CRQEN | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00 | SCCR_EBDF01)
-#else
-#define CONFIG_SYS_SCCR	(/* SCCR_TBS	| */ SCCR_CRQEN | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#endif
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define	CONFIG_SYS_DER	0x2002000F*/
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_BI | OR_SCY_5_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-#if CONFIG_NETPHONE_VERSION == 2
-
-#define FLASH_BASE4_PRELIM	0x40080000	/* FLASH bank #1	*/
-
-#define CONFIG_SYS_OR4_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR4_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR4_PRELIM	((FLASH_BASE4_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-#endif
-
-/*
- * BR3 and OR3 (SDRAM)
- *
- */
-#define SDRAM_BASE3_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define	SDRAM_MAX_SIZE		(256 << 20)	/* max 256MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	(OR_CSNT_SAM | OR_G5LS)
-
-#define CONFIG_SYS_OR3_PRELIM	((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM)
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V)
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_MAMR_PTA		 234
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_LAST_STAGE_INIT		/* needed to reset the damn phys */
-
-/****************************************************************/
-
-#define DSP_SIZE	0x00010000	/* 64K */
-#define NAND_SIZE	0x00010000	/* 64K */
-
-#define DSP_BASE	0xF1000000
-#define NAND_BASE	0xF1010000
-
-/*****************************************************************************/
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP
-
-/*****************************************************************************/
-
-#if CONFIG_NETPHONE_VERSION == 1
-#define STATUS_LED_BIT		0x00000008		/* bit 28 */
-#elif CONFIG_NETPHONE_VERSION == 2
-#define STATUS_LED_BIT		0x00000080		/* bit 24 */
-#endif
-
-#define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 2)
-#define STATUS_LED_STATE	STATUS_LED_BLINKING
-
-#define STATUS_LED_ACTIVE	0		/* LED on for bit == 0	*/
-#define STATUS_LED_BOOT		0		/* LED 0 used for boot status */
-
-#ifndef __ASSEMBLY__
-
-/* LEDs */
-
-/* led_id_t is unsigned int mask */
-typedef unsigned int led_id_t;
-
-#define __led_toggle(_msk) \
-	do { \
-		((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat ^= (_msk); \
-	} while(0)
-
-#define __led_set(_msk, _st) \
-	do { \
-		if ((_st)) \
-			((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat |= (_msk); \
-		else \
-			((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat &= ~(_msk); \
-	} while(0)
-
-#define __led_init(msk, st) __led_set(msk, st)
-
-#endif
-
-/***********************************************************************************************************
-
- ----------------------------------------------------------------------------------------------
-
-   (V1) version 1 of the board
-   (V2) version 2 of the board
-
- ----------------------------------------------------------------------------------------------
-
-   Pin definitions:
-
- +------+----------------+--------+------------------------------------------------------------
- |  #   | Name           | Type   | Comment
- +------+----------------+--------+------------------------------------------------------------
- | PA3  | SPIEN_MAX      | Output | MAX serial to uart chip select
- | PA7  | DSP_INT        | Output | DSP interrupt
- | PA10 | DSP_RESET      | Output | DSP reset
- | PA14 | USBOE          | Output | USB (1)
- | PA15 | USBRXD         | Output | USB (1)
- | PB19 | BT_RTS         | Output | Bluetooth (0)
- | PB23 | BT_CTS         | Output | Bluetooth (0)
- | PB26 | SPIEN_SEP      | Output | Serial EEPROM chip select
- | PB27 | SPICS_DISP     | Output | Display chip select
- | PB28 | SPI_RXD_3V     | Input  | SPI Data Rx
- | PB29 | SPI_TXD        | Output | SPI Data Tx
- | PB30 | SPI_CLK        | Output | SPI Clock
- | PC10 | DISPA0         | Output | Display A0
- | PC11 | BACKLIGHT      | Output | Display backlit
- | PC12 | SPI2RXD        | Input  | (V1) 2nd SPI RXD
- |      | IO_RESET       | Output | (V2) General I/O reset
- | PC13 | SPI2TXD        | Output | (V1) 2nd SPI TXD (V1)
- |      | HOOK           | Input  | (V2) Hook input interrupt
- | PC15 | SPI2CLK        | Output | (V1) 2nd SPI CLK
- |      | F_RY_BY        | Input  | (V2) NAND F_RY_BY
- | PE17 | F_ALE          | Output | NAND F_ALE
- | PE18 | F_CLE          | Output | NAND F_CLE
- | PE20 | F_CE           | Output | NAND F_CE
- | PE24 | SPICS_SCOUT    | Output | (V1) Codec chip select
- |      | LED            | Output | (V2) LED
- | PE27 | SPICS_ER       | Output | External serial register CS
- | PE28 | LEDIO1         | Output | (V1) LED
- |      | BKBR1          | Input  | (V2) Keyboard input scan
- | PE29 | LEDIO2         | Output | (V1) LED hook for A (TA2)
- |      | BKBR2          | Input  | (V2) Keyboard input scan
- | PE30 | LEDIO3         | Output | (V1) LED hook for A (TA2)
- |      | BKBR3          | Input  | (V2) Keyboard input scan
- | PE31 | F_RY_BY        | Input  | (V1) NAND F_RY_BY
- |      | BKBR4          | Input  | (V2) Keyboard input scan
- +------+----------------+--------+---------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
-   Serial register input:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- |    0 | BKBR1          | (V1) Keyboard input scan
- |    1 | BKBR3          | (V1) Keyboard input scan
- |    2 | BKBR4          | (V1) Keyboard input scan
- |    3 | BKBR2          | (V1) Keyboard input scan
- |    4 | HOOK           | (V1) Hook switch
- |    5 | BT_LINK        | (V1) Bluetooth link status
- |    6 | HOST_WAKE      | (V1) Bluetooth host wake up
- |    7 | OK_ETH         | (V1) Cisco inline power OK status
- +------+----------------+------------------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
-   Serial register output:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- |    0 | KEY1           | Keyboard output scan
- |    1 | KEY2           | Keyboard output scan
- |    2 | KEY3           | Keyboard output scan
- |    3 | KEY4           | Keyboard output scan
- |    4 | KEY5           | Keyboard output scan
- |    5 | KEY6           | Keyboard output scan
- |    6 | KEY7           | Keyboard output scan
- |    7 | BT_WAKE        | Bluetooth wake up
- +------+----------------+------------------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
- Chip selects:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | CS0  | CS0            | Boot flash
- | CS1  | CS_FLASH       | NAND flash
- | CS2  | CS_DSP         | DSP
- | CS3  | DCS_DRAM       | DRAM
- | CS4  | CS_FLASH2      | (V2) 2nd flash
- +------+----------------+------------------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
- Interrupts:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | IRQ1 | IRQ_DSP        | DSP interrupt
- | IRQ3 | S_INTER        | DUSLIC ???
- | IRQ4 | F_RY_BY        | NAND
- | IRQ7 | IRQ_MAX        | MAX 3100 interrupt
- +------+----------------+------------------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
- Interrupts on PCMCIA pins:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | IP_A0| PHY1_LINK      | Link status changed for #1 Ethernet interface
- | IP_A1| PHY2_LINK      | Link status changed for #2 Ethernet interface
- | IP_A2| RMII1_MDINT    | PHY interrupt for #1
- | IP_A3| RMII2_MDINT    | PHY interrupt for #2
- | IP_A5| HOST_WAKE      | (V2) Bluetooth host wake
- | IP_A6| OK_ETH         | (V2) Cisco inline power OK
- +------+----------------+------------------------------------------------------------
-
-*************************************************************************************************/
-
-#define CONFIG_SED156X			1	/* use SED156X */
-#define CONFIG_SED156X_PG12864Q		1	/* type of display used */
-
-/* serial interfacing macros */
-
-#define SED156X_SPI_RXD_PORT	(((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
-#define SED156X_SPI_RXD_MASK	0x00000008
-
-#define SED156X_SPI_TXD_PORT	(((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
-#define SED156X_SPI_TXD_MASK	0x00000004
-
-#define SED156X_SPI_CLK_PORT	(((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
-#define SED156X_SPI_CLK_MASK	0x00000002
-
-#define SED156X_CS_PORT		(((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
-#define SED156X_CS_MASK		0x00000010
-
-#define SED156X_A0_PORT		(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat)
-#define SED156X_A0_MASK		0x0020
-
-/*************************************************************************************************/
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV		1
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE	1
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE	1
-
-/*************************************************************************************************/
-
-/* use board specific hardware */
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_SHOW_ACTIVITY
-
-/*************************************************************************************************/
-
-/* phone console configuration */
-
-#define PHONE_CONSOLE_POLL_HZ		(CONFIG_SYS_HZ/200)	/* poll every 5ms */
-
-/*************************************************************************************************/
-
-#define CONFIG_CDP_DEVICE_ID		20
-#define CONFIG_CDP_DEVICE_ID_PREFIX	"NP"	/* netphone */
-#define CONFIG_CDP_PORT_ID		"eth%d"
-#define CONFIG_CDP_CAPABILITIES		0x00000010
-#define CONFIG_CDP_VERSION		"u-boot" " " U_BOOT_DATE " " U_BOOT_TIME
-#define CONFIG_CDP_PLATFORM		"Intracom NetPhone"
-#define CONFIG_CDP_TRIGGER		0x20020001
-#define CONFIG_CDP_POWER_CONSUMPTION	4300	/* 90 mA @ 48V */
-#define CONFIG_CDP_APPLIANCE_VLAN_TYPE	0x01	/* ipphone */
-
-/*************************************************************************************************/
-
-#define CONFIG_AUTO_COMPLETE	1
-
-/*************************************************************************************************/
-
-#define CONFIG_CRC32_VERIFY	1
-
-/*************************************************************************************************/
-
-#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE	1
-
-/*************************************************************************************************/
-#endif	/* __CONFIG_H */
diff --git a/include/configs/NETTA.h b/include/configs/NETTA.h
deleted file mode 100644
index 800a922..0000000
--- a/include/configs/NETTA.h
+++ /dev/null
@@ -1,666 +0,0 @@
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Pantelis Antoniou, Intracom S.A., panto@intracom.gr
- * U-Boot port on NetTA4 board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC885		1	/* This is a MPC885 CPU		*/
-#define CONFIG_NETTA		1	/* ...on a NetTA board		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-/* #define CONFIG_XIN		 10000000 */
-#define CONFIG_XIN		 50000000
-#define MPC8XX_HZ		120000000
-/* #define MPC8XX_HZ		100000000 */
-/* #define MPC8XX_HZ		 50000000 */
-/* #define MPC8XX_HZ		 80000000 */
-
-#define CONFIG_8xx_GCLK_FREQ	MPC8XX_HZ
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#undef	CONFIG_CLOCKS_IN_MHZ	/* clocks NOT passsed to Linux in MHz */
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"tftpboot; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"	\
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	0	/* echo off for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-#define CONFIG_HW_WATCHDOG
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_NISDOMAIN
-
-
-#undef CONFIG_MAC_PARTITION
-#undef CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-#define	FEC_ENET		1	/* eth.c needs it that way... */
-#undef  CONFIG_SYS_DISCOVER_PHY		/* do not discover phys */
-#define CONFIG_MII		1
-#define CONFIG_MII_INIT		1
-#define CONFIG_RMII		1	/* use RMII interface */
-
-#if defined(CONFIG_NETTA_ISDN)
-#define CONFIG_ETHER_ON_FEC1	1
-#define CONFIG_FEC1_PHY		1	/* phy address of FEC1 */
-#define CONFIG_FEC1_PHY_NORXERR 1
-#undef  CONFIG_ETHER_ON_FEC2
-#else
-#define CONFIG_ETHER_ON_FEC1	1
-#define CONFIG_FEC1_PHY		8	/* phy address of FEC1 */
-#define CONFIG_FEC1_PHY_NORXERR 1
-#define CONFIG_ETHER_ON_FEC2	1
-#define CONFIG_FEC2_PHY		1	/* phy address of FEC2 */
-#define CONFIG_FEC2_PHY_NORXERR 1
-#endif
-
-#define CONFIG_ENV_OVERWRITE	1	/* allow modification of vendor params */
-
-/* POST support */
-#define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
-				 CONFIG_SYS_POST_CODEC	   | \
-				 CONFIG_SYS_POST_DSP	   )
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_CDP
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_PING
-
-
-#define CONFIG_BOARD_EARLY_INIT_F	1
-#define CONFIG_MISC_INIT_R
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_SYS_HUSH_PARSER	1
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0300000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0700000	/* 3 ... 7 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x3000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#if defined(DEBUG)
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SECT_SIZE	0x10000
-
-#define	CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x60000)
-#define	CONFIG_ENV_SIZE		0x4000
-
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_SYS_FLASH_BASE + 0x70000)
-#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- */
-
-#if CONFIG_XIN == 10000000
-
-#if MPC8XX_HZ == 120000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 100000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 50000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 25000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 40000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 75000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#else
-#error unsupported CPU freq for XIN = 10MHz
-#endif
-
-#elif CONFIG_XIN == 50000000
-
-#if MPC8XX_HZ == 120000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 100000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ ==  80000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ ==  50000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#else
-#error unsupported CPU freq for XIN = 50MHz
-#endif
-
-#else
-
-#error unsupported XIN freq
-#endif
-
-
-/*
- *-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- *
- * Note: When TBS == 0 the timebase is independent of current cpu clock.
- */
-
-#define SCCR_MASK	SCCR_EBDF11
-#if MPC8XX_HZ > 66666666
-#define CONFIG_SYS_SCCR	(/* SCCR_TBS	| */ SCCR_CRQEN | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL111 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00 | SCCR_EBDF01)
-#else
-#define CONFIG_SYS_SCCR	(/* SCCR_TBS	| */ SCCR_CRQEN | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL111 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#endif
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define	CONFIG_SYS_DER	0x2002000F*/
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_BI | OR_SCY_5_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-/*
- * BR3 and OR3 (SDRAM)
- *
- */
-#define SDRAM_BASE3_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define	SDRAM_MAX_SIZE		(256 << 20)	/* max 256MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	(OR_CSNT_SAM | OR_G5LS)
-
-#define CONFIG_SYS_OR3_PRELIM	((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM)
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V)
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#if   MPC8XX_HZ == 120000000
-#define CONFIG_SYS_MAMR_PTA		 234
-#elif MPC8XX_HZ == 100000000
-#define CONFIG_SYS_MAMR_PTA		 195
-#elif MPC8XX_HZ ==  80000000
-#define CONFIG_SYS_MAMR_PTA		 156
-#elif MPC8XX_HZ ==  50000000
-#define CONFIG_SYS_MAMR_PTA		  98
-#else
-#error Unknown frequency
-#endif
-
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_LAST_STAGE_INIT		/* needed to reset the damn phys */
-
-/***********************************************************************************************************
-
-   Pin definitions:
-
- +------+----------------+--------+------------------------------------------------------------
- |  #   | Name           | Type   | Comment
- +------+----------------+--------+------------------------------------------------------------
- | PA3  | OK_ETH_3V      | Input  | CISCO Ethernet power OK
- |      |                |        | (NetRoute: FEC1, TA: FEC2) (0=power OK)
- | PA6  | P_VCCD1        | Output | TPS2211A PCMCIA
- | PA7  | DCL1_3V        | Periph | IDL1 PCM clock
- | PA8  | DSP_DR1        | Periph | IDL1 PCM Data Rx
- | PA9  | L1TXDA         | Periph | IDL1 PCM Data Tx
- | PA10 | P_VCCD0        | Output | TPS2211A PCMCIA
- | PA12 | P_SHDN         | Output | TPS2211A PCMCIA
- | PA13 | ETH_LOOP       | Output | CISCO Loopback remote power
- |      |                |        | (NetRoute: FEC1, TA: FEC2) (1=NORMAL)
- | PA14 | P_VPPD0        | Output | TPS2211A PCMCIA
- | PA15 | P_VPPD1        | Output | TPS2211A PCMCIA
- | PB14 | SPIEN_FXO      | Output | SPI CS for FXO daughter-board
- | PB15 | SPIEN_S1       | Output | SPI CS for S-interface 1 (NetRoute only)
- | PB16 | DREQ1          | Output | D channel request for S-interface chip 1.
- | PB17 | L1ST3          | Periph | IDL1 timeslot enable signal for PPC
- | PB18 | L1ST2          | Periph | IDL1 timeslot enable signal for PPC
- | PB19 | SPIEN_S2       | Output | SPI CS for S-interface 2 (NetRoute only)
- | PB20 | SPIEN_SEEPROM  | Output | SPI CS for serial eeprom
- | PB21 | LEDIO          | Output | Led mode indication for PHY
- | PB22 | UART_CTS       | Input  | UART CTS
- | PB23 | UART_RTS       | Output | UART RTS
- | PB24 | UART_RX        | Periph | UART Data Rx
- | PB25 | UART_TX        | Periph | UART Data Tx
- | PB26 | RMII-MDC       | Periph | Free for future use (MII mgt clock)
- | PB27 | RMII-MDIO      | Periph | Free for future use (MII mgt data)
- | PB28 | SPI_RXD_3V     | Input  | SPI Data Rx
- | PB29 | SPI_TXD        | Output | SPI Data Tx
- | PB30 | SPI_CLK        | Output | SPI Clock
- | PB31 | RMII1-REFCLK   | Periph | RMII reference clock for FEC1
- | PC4  | PHY1_LINK      | Input  | PHY link state FEC1 (interrupt)
- | PC5  | PHY2_LINK      | Input  | PHY link state FEC2 (interrupt)
- | PC6  | RMII1-MDINT    | Input  | PHY prog interrupt FEC1 (interrupt)
- | PC7  | RMII2-MDINT    | Input  | PHY prog interrupt FEC1 (interrupt)
- | PC8  | P_OC           | Input  | TPS2211A PCMCIA overcurrent (interrupt) (1=OK)
- | PC9  | COM_HOOK1      | Input  | Codec interrupt chip #1 (interrupt)
- | PC10 | COM_HOOK2      | Input  | Codec interrupt chip #2 (interrupt)
- | PC11 | COM_HOOK4      | Input  | Codec interrupt chip #4 (interrupt)
- | PC12 | COM_HOOK3      | Input  | Codec interrupt chip #3 (interrupt)
- | PC13 | F_RY_BY        | Input  | NAND ready signal (interrupt)
- | PC14 | FAN_OK         | Input  | Fan status signal (interrupt) (1=OK)
- | PC15 | PC15_DIRECT0   | Periph | PCMCIA DMA request.
- | PD3  | F_ALE          | Output | NAND
- | PD4  | F_CLE          | Output | NAND
- | PD5  | F_CE           | Output | NAND
- | PD6  | DSP_INT        | Output | DSP debug interrupt
- | PD7  | DSP_RESET      | Output | DSP reset
- | PD8  | RMII_MDC       | Periph | MII mgt clock
- | PD9  | SPIEN_C1       | Output | SPI CS for codec #1
- | PD10 | SPIEN_C2       | Output | SPI CS for codec #2
- | PD11 | SPIEN_C3       | Output | SPI CS for codec #3
- | PD12 | FSC2           | Periph | IDL2 frame sync
- | PD13 | DGRANT2        | Input  | D channel grant from S #2
- | PD14 | SPIEN_C4       | Output | SPI CS for codec #4
- | PD15 | TP700          | Output | Testpoint for software debugging
- | PE14 | RMII2-TXD0     | Periph | FEC2 transmit data
- | PE15 | RMII2-TXD1     | Periph | FEC2 transmit data
- | PE16 | RMII2-REFCLK   | Periph | TA: RMII ref clock for
- |      | DCL2           | Periph | NetRoute: PCM clock #2
- | PE17 | TP703          | Output | Testpoint for software debugging
- | PE18 | DGRANT1        | Input  |  D channel grant from S #1
- | PE19 | RMII2-TXEN     | Periph | TA: FEC2 tx enable
- |      | PCM2OUT        | Periph | NetRoute: Tx data for IDL2
- | PE20 | FSC1           | Periph | IDL1 frame sync
- | PE21 | RMII2-RXD0     | Periph | FEC2 receive data
- | PE22 | RMII2-RXD1     | Periph | FEC2 receive data
- | PE23 | L1ST1          | Periph | IDL1 timeslot enable signal for PPC
- | PE24 | U-N1           | Output | Select user/network for S #1 (0=user)
- | PE25 | U-N2           | Output | Select user/network for S #2 (0=user)
- | PE26 | RMII2-RXDV     | Periph | FEC2 valid
- | PE27 | DREQ2          | Output | D channel request for S #2.
- | PE28 | FPGA_DONE      | Input  | FPGA done signal
- | PE29 | FPGA_INIT      | Output | FPGA init signal
- | PE30 | UDOUT2_3V      | Input  | IDL2 PCM input
- | PE31 |                |        | Free
- +------+----------------+--------+---------------------------------------------------
-
- Chip selects:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | CS0  | CS0            | Boot flash
- | CS1  | CS_FLASH       | NAND flash
- | CS2  | CS_DSP         | DSP
- | CS3  | DCS_DRAM       | DRAM
- | CS4  | CS_ER1         | External output register
- +------+----------------+------------------------------------------------------------
-
- Interrupts:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | IRQ1 | UINTER_3V      | S interrupt chips interrupt (common)
- | IRQ3 | IRQ_DSP        | DSP interrupt
- | IRQ4 | IRQ_DSP1       | Extra DSP interrupt
- +------+----------------+------------------------------------------------------------
-
-*************************************************************************************************/
-
-#define DSP_SIZE	0x00010000	/* 64K */
-#define NAND_SIZE	0x00010000	/* 64K */
-#define ER_SIZE		0x00010000	/* 64K */
-#define DUMMY_SIZE	0x00010000	/* 64K */
-
-#define DSP_BASE	0xF1000000
-#define NAND_BASE	0xF1010000
-#define ER_BASE		0xF1020000
-#define DUMMY_BASE	0xF1FF0000
-
-/*****************************************************************************/
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP
-#define CONFIG_SYS_DIRECT_NAND_TFTP
-
-/*****************************************************************************/
-
-#if 1
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#endif
-
-/*************************************************************************************************/
-
-#define CONFIG_CDP_DEVICE_ID		20
-#define CONFIG_CDP_DEVICE_ID_PREFIX	"NT"	/* netta */
-#define CONFIG_CDP_PORT_ID		"eth%d"
-#define CONFIG_CDP_CAPABILITIES		0x00000010
-#define CONFIG_CDP_VERSION		"u-boot 1.0" " " U_BOOT_DATE " " U_BOOT_TIME
-#define CONFIG_CDP_PLATFORM		"Intracom NetTA"
-#define CONFIG_CDP_TRIGGER		0x20020001
-#define CONFIG_CDP_POWER_CONSUMPTION	4300	/* 90 mA @ 48V */
-#define CONFIG_CDP_APPLIANCE_VLAN_TYPE	0x01	/* ipphone? */
-
-/*************************************************************************************************/
-
-#define CONFIG_AUTO_COMPLETE	1
-
-/*************************************************************************************************/
-
-#define CONFIG_CRC32_VERIFY	1
-
-/*************************************************************************************************/
-
-#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE	1
-
-/*************************************************************************************************/
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/NETTA2.h b/include/configs/NETTA2.h
deleted file mode 100644
index 55ae4b5..0000000
--- a/include/configs/NETTA2.h
+++ /dev/null
@@ -1,654 +0,0 @@
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Pantelis Antoniou, Intracom S.A., panto@intracom.gr
- * U-Boot port on NetTA4 board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#if !defined(CONFIG_NETTA2_VERSION) || CONFIG_NETTA2_VERSION > 2
-#error Unsupported CONFIG_NETTA2 version
-#endif
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC870		1	/* This is a MPC885 CPU		*/
-#define CONFIG_NETTA2		1	/* ...on a NetTA2 board		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-/* #define CONFIG_XIN		 10000000 */
-#define CONFIG_XIN		 50000000
-/* #define MPC8XX_HZ		120000000 */
-#define MPC8XX_HZ		 66666666
-
-#define CONFIG_8xx_GCLK_FREQ	MPC8XX_HZ
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#undef	CONFIG_CLOCKS_IN_MHZ	/* clocks NOT passsed to Linux in MHz */
-
-#define CONFIG_PREBOOT	"echo;"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"tftpboot; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#define CONFIG_SOURCE
-#define CONFIG_LOADS_ECHO	0	/* echo off for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
-
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-#define CONFIG_BOARD_SPECIFIC_LED	/* version has board specific leds */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_NISDOMAIN
-
-
-#undef CONFIG_MAC_PARTITION
-#undef CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-#define	FEC_ENET		1	/* eth.c needs it that way... */
-#undef CONFIG_SYS_DISCOVER_PHY
-#define CONFIG_MII		1
-#define CONFIG_MII_INIT		1
-#define CONFIG_RMII		1	/* use RMII interface */
-
-#define CONFIG_ETHER_ON_FEC1	1
-#define CONFIG_FEC1_PHY		8	/* phy address of FEC */
-#define CONFIG_FEC1_PHY_NORXERR 1
-
-#define CONFIG_ETHER_ON_FEC2	1
-#define CONFIG_FEC2_PHY		4
-#define CONFIG_FEC2_PHY_NORXERR 1
-
-#define CONFIG_ENV_OVERWRITE	1	/* allow modification of vendor params */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_CDP
-
-
-#define CONFIG_BOARD_EARLY_INIT_F	1
-#define CONFIG_MISC_INIT_R
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_SYS_HUSH_PARSER	1
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0300000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0700000	/* 3 ... 7 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x3000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#if defined(DEBUG)
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-#if CONFIG_NETTA2_VERSION == 2
-#define CONFIG_SYS_FLASH_BASE4		0x40080000
-#endif
-
-#define CONFIG_SYS_RESET_ADDRESS   0x80000000
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#if CONFIG_NETTA2_VERSION == 1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#elif CONFIG_NETTA2_VERSION == 2
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#endif
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SECT_SIZE	0x10000
-
-#define	CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x60000)
-#define CONFIG_ENV_OFFSET		0
-#define	CONFIG_ENV_SIZE		0x4000
-
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_SYS_FLASH_BASE + 0x70000)
-#define CONFIG_ENV_OFFSET_REDUND	0
-#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef	CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- */
-
-#if CONFIG_XIN == 10000000
-
-#if MPC8XX_HZ == 120000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 100000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 50000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 25000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 40000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 75000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#else
-#error unsupported CPU freq for XIN = 10MHz
-#endif
-
-#elif CONFIG_XIN == 50000000
-
-#if MPC8XX_HZ == 120000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ == 100000000
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#elif MPC8XX_HZ ==  66666666
-#define CONFIG_SYS_PLPRCR	((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
-			 (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
-			 PLPRCR_TEXPS)
-#else
-#error unsupported CPU freq for XIN = 50MHz
-#endif
-
-#else
-
-#error unsupported XIN freq
-#endif
-
-
-/*
- *-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- *
- * Note: When TBS == 0 the timebase is independent of current cpu clock.
- */
-
-#define SCCR_MASK	SCCR_EBDF11
-#if MPC8XX_HZ > 66666666
-#define CONFIG_SYS_SCCR	(/* SCCR_TBS     | */ SCCR_CRQEN | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00 | SCCR_EBDF01)
-#else
-#define CONFIG_SYS_SCCR	(/* SCCR_TBS     | */ SCCR_CRQEN | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#endif
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define	CONFIG_SYS_DER	0x2002000F*/
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_BI | OR_SCY_5_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-#if CONFIG_NETTA2_VERSION == 2
-
-#define FLASH_BASE4_PRELIM	0x40080000	/* FLASH bank #1	*/
-
-#define CONFIG_SYS_OR4_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR4_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR4_PRELIM	((FLASH_BASE4_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-#endif
-
-/*
- * BR3 and OR3 (SDRAM)
- *
- */
-#define SDRAM_BASE3_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define	SDRAM_MAX_SIZE		(256 << 20)	/* max 256MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	(OR_CSNT_SAM | OR_G5LS)
-
-#define CONFIG_SYS_OR3_PRELIM	((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM)
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V)
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_MAMR_PTA		 234
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_LAST_STAGE_INIT		/* needed to reset the damn phys */
-
-/****************************************************************/
-
-#define DSP_SIZE	0x00010000	/* 64K */
-#define NAND_SIZE	0x00010000	/* 64K */
-
-#define DSP_BASE	0xF1000000
-#define NAND_BASE	0xF1010000
-
-/*****************************************************************************/
-
-#define CONFIG_SYS_DIRECT_FLASH_TFTP
-
-/*****************************************************************************/
-
-#if CONFIG_NETTA2_VERSION == 1
-#define STATUS_LED_BIT		0x00000008		/* bit 28 */
-#elif CONFIG_NETTA2_VERSION == 2
-#define STATUS_LED_BIT		0x00000080		/* bit 24 */
-#endif
-
-#define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 2)
-#define STATUS_LED_STATE	STATUS_LED_BLINKING
-
-#define STATUS_LED_ACTIVE	0		/* LED on for bit == 0	*/
-#define STATUS_LED_BOOT		0		/* LED 0 used for boot status */
-
-#ifndef __ASSEMBLY__
-
-/* LEDs */
-
-/* led_id_t is unsigned int mask */
-typedef unsigned int led_id_t;
-
-#define __led_toggle(_msk) \
-	do { \
-		((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat ^= (_msk); \
-	} while(0)
-
-#define __led_set(_msk, _st) \
-	do { \
-		if ((_st)) \
-			((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat |= (_msk); \
-		else \
-			((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat &= ~(_msk); \
-	} while(0)
-
-#define __led_init(msk, st) __led_set(msk, st)
-
-#endif
-
-/***********************************************************************************************************
-
- ----------------------------------------------------------------------------------------------
-
-   (V1) version 1 of the board
-   (V2) version 2 of the board
-
- ----------------------------------------------------------------------------------------------
-
-   Pin definitions:
-
- +------+----------------+--------+------------------------------------------------------------
- |  #   | Name           | Type   | Comment
- +------+----------------+--------+------------------------------------------------------------
- | PA3  | SPIEN_MAX      | Output | MAX serial to uart chip select
- | PA7  | DSP_INT        | Output | DSP interrupt
- | PA10 | DSP_RESET      | Output | DSP reset
- | PA14 | USBOE          | Output | USB (1)
- | PA15 | USBRXD         | Output | USB (1)
- | PB19 | BT_RTS         | Output | Bluetooth (0)
- | PB23 | BT_CTS         | Output | Bluetooth (0)
- | PB26 | SPIEN_SEP      | Output | Serial EEPROM chip select
- | PB27 | SPICS_DISP     | Output | Display chip select
- | PB28 | SPI_RXD_3V     | Input  | SPI Data Rx
- | PB29 | SPI_TXD        | Output | SPI Data Tx
- | PB30 | SPI_CLK        | Output | SPI Clock
- | PC10 | DISPA0         | Output | Display A0
- | PC11 | BACKLIGHT      | Output | Display backlit
- | PC12 | SPI2RXD        | Input  | (V1) 2nd SPI RXD
- |      | IO_RESET       | Output | (V2) General I/O reset
- | PC13 | SPI2TXD        | Output | (V1) 2nd SPI TXD (V1)
- |      | HOOK           | Input  | (V2) Hook input interrupt
- | PC15 | SPI2CLK        | Output | (V1) 2nd SPI CLK
- |      | F_RY_BY        | Input  | (V2) NAND F_RY_BY
- | PE17 | F_ALE          | Output | NAND F_ALE
- | PE18 | F_CLE          | Output | NAND F_CLE
- | PE20 | F_CE           | Output | NAND F_CE
- | PE24 | SPICS_SCOUT    | Output | (V1) Codec chip select
- |      | LED            | Output | (V2) LED
- | PE27 | SPICS_ER       | Output | External serial register CS
- | PE28 | LEDIO1         | Output | (V1) LED
- |      | BKBR1          | Input  | (V2) Keyboard input scan
- | PE29 | LEDIO2         | Output | (V1) LED hook for A (TA2)
- |      | BKBR2          | Input  | (V2) Keyboard input scan
- | PE30 | LEDIO3         | Output | (V1) LED hook for A (TA2)
- |      | BKBR3          | Input  | (V2) Keyboard input scan
- | PE31 | F_RY_BY        | Input  | (V1) NAND F_RY_BY
- |      | BKBR4          | Input  | (V2) Keyboard input scan
- +------+----------------+--------+---------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
-   Serial register input:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- |    4 | HOOK           | Hook switch
- |    5 | BT_LINK        | Bluetooth link status
- |    6 | HOST_WAKE      | Bluetooth host wake up
- |    7 | OK_ETH         | Cisco inline power OK status
- +------+----------------+------------------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
- Chip selects:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | CS0  | CS0            | Boot flash
- | CS1  | CS_FLASH       | NAND flash
- | CS2  | CS_DSP         | DSP
- | CS3  | DCS_DRAM       | DRAM
- | CS4  | CS_FLASH2      | (V2) 2nd flash
- +------+----------------+------------------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
- Interrupts:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | IRQ1 | IRQ_DSP        | DSP interrupt
- | IRQ3 | S_INTER        | DUSLIC ???
- | IRQ4 | F_RY_BY        | NAND
- | IRQ7 | IRQ_MAX        | MAX 3100 interrupt
- +------+----------------+------------------------------------------------------------
-
- ----------------------------------------------------------------------------------------------
-
- Interrupts on PCMCIA pins:
-
- +------+----------------+------------------------------------------------------------
- |  #   | Name           | Comment
- +------+----------------+------------------------------------------------------------
- | IP_A0| PHY1_LINK      | Link status changed for #1 Ethernet interface
- | IP_A1| PHY2_LINK      | Link status changed for #2 Ethernet interface
- | IP_A2| RMII1_MDINT    | PHY interrupt for #1
- | IP_A3| RMII2_MDINT    | PHY interrupt for #2
- | IP_A5| HOST_WAKE      | (V2) Bluetooth host wake
- | IP_A6| OK_ETH         | (V2) Cisco inline power OK
- +------+----------------+------------------------------------------------------------
-
-**************************************************************************************************/
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV		1
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE	1
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE	1
-
-/*************************************************************************************************/
-
-/* use board specific hardware */
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-#define CONFIG_HW_WATCHDOG
-
-/*************************************************************************************************/
-
-#define CONFIG_CDP_DEVICE_ID		20
-#define CONFIG_CDP_DEVICE_ID_PREFIX	"NT"	/* netta2 */
-#define CONFIG_CDP_PORT_ID		"eth%d"
-#define CONFIG_CDP_CAPABILITIES		0x00000010
-#define CONFIG_CDP_VERSION		"u-boot" " " U_BOOT_DATE " " U_BOOT_TIME
-#define CONFIG_CDP_PLATFORM		"Intracom NetTA2"
-#define CONFIG_CDP_TRIGGER		0x20020001
-#define CONFIG_CDP_POWER_CONSUMPTION	4300	/* 90 mA @ 48V */
-#define CONFIG_CDP_APPLIANCE_VLAN_TYPE	0x01	/* ipphone ? */
-
-/*************************************************************************************************/
-
-#define CONFIG_AUTO_COMPLETE	1
-
-/*************************************************************************************************/
-
-#define CONFIG_CRC32_VERIFY	1
-
-/*************************************************************************************************/
-
-#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE	1
-
-/*************************************************************************************************/
-#endif	/* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index b0f6b92..b1f325b 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -41,8 +41,6 @@
 # define CONFIG_PCMCIA_SLOT_B
 #elif defined(CONFIG_ATC)		/* The ATC use SLOT_A	*/
 # define CONFIG_PCMCIA_SLOT_A
-#elif defined(CONFIG_NETTA)
-# define CONFIG_PCMCIA_SLOT_A
 #elif defined(CONFIG_UC100)		/* The UC100 use SLOT_B	        */
 # define CONFIG_PCMCIA_SLOT_B
 #else
diff --git a/include/status_led.h b/include/status_led.h
index 61eb66a..0eb91b8 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -231,9 +231,6 @@ void status_led_set  (int led, int state);
 
 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
 
-/*****  NetPhone   ********************************************************/
-#elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2)
-/* XXX empty just to avoid the error */
 /*****  STx XTc    ********************************************************/
 #elif defined(CONFIG_STXXTC)
 /* XXX empty just to avoid the error */