powerpc: remove RPXClassic, RPXlite boards support

Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove board/RPXlite/*
 - Remove board/RPXClassic/*
 - Remove include/configs/RPXlite.h
 - Remove include/configs/RPXClassic.h
 - Clean-up defined(CONFIG_RPXCLASSIC)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

5 files changed, 1 insertions, 918 deletions

diff --git a/include/common.h b/include/common.h
index 580615b..baf361b 100644
--- a/include/common.h
+++ b/include/common.h
@@ -505,10 +505,6 @@ extern ssize_t spi_read	 (uchar *, int, uchar *, int);
 extern ssize_t spi_write (uchar *, int, uchar *, int);
 #endif
 
-#ifdef CONFIG_RPXCLASSIC
-void rpxclassic_init (void);
-#endif
-
 void rpxlite_init (void);
 
 #ifdef CONFIG_HERMES
diff --git a/include/commproc.h b/include/commproc.h
index 605aac2..29a3e61 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -954,41 +954,6 @@ typedef struct scc_enet {
 
 #endif /* CONFIG_QS860T */
 
-/***  RPXCLASSIC  *****************************************************/
-
-#ifdef CONFIG_RPXCLASSIC
-
-#ifdef CONFIG_FEC_ENET
-
-# define FEC_ENET				/* use FEC for EThernet */
-# undef SCC_ENET
-
-#else	/* ! CONFIG_FEC_ENET */
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PB_ENET_TENA	((uint)0x00001000)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-
-#endif	/* CONFIG_FEC_ENET */
-
-#endif	/* CONFIG_RPXCLASSIC */
-
 /***  RPXLITE  ********************************************************/
 
 #ifdef CONFIG_RPXLITE
diff --git a/include/configs/RPXClassic.h b/include/configs/RPXClassic.h
deleted file mode 100644
index 0f07d0c..0000000
--- a/include/configs/RPXClassic.h
+++ /dev/null
@@ -1,483 +0,0 @@
-/*
- * (C) Copyright 2000, 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
- * U-Boot port on RPXlite board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	RPXClassic_50MHz
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860           1
-#define CONFIG_RPXCLASSIC		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xff000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600	/* console baudrate = 9600bps	*/
-
-/* Define CONFIG_FEC_ENET to use Fast ethernet instead of ethernet on SCC1   */
-#define CONFIG_FEC_ENET
-#ifdef CONFIG_FEC_ENET
-#define CONFIG_SYS_DISCOVER_PHY        1
-#define CONFIG_MII              1
-#endif /* CONFIG_FEC_ENET */
-#define CONFIG_MISC_INIT_R
-
-/* Video console (graphic: Epson SED13806 on ECCX board, no keyboard         */
-#if 1
-#define CONFIG_VIDEO_SED13806
-#define CONFIG_NEC_NL6448BC20
-#define CONFIG_VIDEO_SED13806_16BPP
-
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
-#endif
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK 1
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"tftpboot; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_RESET_ADDRESS	0x80000000
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0040000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00C0000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFA200000
-
-/*-----------------------------------------------------------------------------
- * I2C Configuration
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_I2C_SPEED		50000
-#define CONFIG_SYS_I2C_SLAVE		0x34
-
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef  CONFIG_SYS_I2C_SOFT		/* I2C bit-banged		*/
-
-#if defined(CONFIG_SYS_I2C_SOFT)
-#define CONFIG_SYS_I2C			1
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT	1		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE	(iop->pdir |=  0x00000010)
-#define I2C_TRISTATE	(iop->pdir &= ~0x00000010)
-#define I2C_READ	((iop->pdat & 0x00000010) != 0)
-#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00000010; \
-			else    iop->pdat &= ~0x00000010
-#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00000020; \
-			else    iop->pdat &= ~0x00000020
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x34
-#endif
-
-# define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM X24C16		*/
-# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x3000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE	0xFF000000
-
-#if defined(DEBUG) || defined (CONFIG_VIDEO_SED13806) || defined(CONFIG_CMD_IDE)
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	0xFF000000
-/*%%% #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE */
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#if 0
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x20000	/*   Offset   of Environment Sector  */
-#define CONFIG_ENV_SECT_SIZE       0x8000
-#define	CONFIG_ENV_SIZE		0x8000	/* Total Size of Environment Sector  */
-#else
-#define CONFIG_ENV_IS_IN_NVRAM     1
-#define CONFIG_ENV_ADDR            0xfa000100
-#define CONFIG_ENV_SIZE            0x1000
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_MLRC10)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-/*%%%#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC |  RTCSC_ALR | RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_PLPRCR	( (4 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS | PLPRCR_SPLSS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF00
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_SCCR	(SCCR_COM00 | SCCR_TBS)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/* #define	CONFIG_SYS_DER	0x2002000F */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE_PRELIM	0xFE000000	/* FLASH base */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFE000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
-
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
-
-/*
- * BR1 and OR1 (SDRAM)
- *
- */
-#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM base	*/
-#define	SDRAM_MAX_SIZE		0x01000000	/* max 16 MB */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000E00
-
-#define CONFIG_SYS_OR1_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR1_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/* RPXLITE mem setting */
-#define	CONFIG_SYS_BR3_PRELIM	0xFA400001		/* BCSR */
-#define CONFIG_SYS_OR3_PRELIM	0xff7f8970
-#define	CONFIG_SYS_BR4_PRELIM	0xFA000401		/* NVRAM&SRAM */
-#define CONFIG_SYS_OR4_PRELIM	0xFFF80970
-
-/* ECCX CS settings                                                          */
-#define SED13806_OR             0xFFC00108     /* - 4 Mo
-						   - Burst inhibit
-						   - external TA             */
-#define SED13806_REG_ADDR       0xa0000000
-#define SED13806_ACCES          0x801           /* 16 bit access             */
-
-
-/* Global definitions for the ECCX board                                     */
-#define ECCX_CSR_ADDR           (0xfac00000)
-#define ECCX_CSR8_OFFSET        (0x8)
-#define ECCX_CSR11_OFFSET       (0xB)
-#define ECCX_CSR12_OFFSET       (0xC)
-
-#define ECCX_CSR8  (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR8_OFFSET)
-#define ECCX_CSR11 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR11_OFFSET)
-#define ECCX_CSR12 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR12_OFFSET)
-
-
-#define REG_GPIO_CTRL 0x008
-
-/* Definitions for CSR8                                                      */
-#define ECCX_ENEPSON            0x80    /* Bit 0:
-					   0= disable and reset SED1386
-					   1= enable SED1386                 */
-/* Bit 1:   0= SED1386 in Big Endian mode                                    */
-/*          1= SED1386 in little endian mode                                 */
-#define ECCX_LE                 0x40
-#define ECCX_BE                 0x00
-
-/* Bit 2,3: Selection                                                        */
-/*      00 = Disabled                                                        */
-/*      01 = CS2 is used for the SED1386                                     */
-/*      10 = CS5 is used for the SED1386                                     */
-/*      11 = reserved                                                        */
-#define ECCX_CS2                0x10
-#define ECCX_CS5                0x20
-
-/* Definitions for CSR12                                                     */
-#define ECCX_ID                 0x02
-#define ECCX_860                0x01
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA	58
-
-/*
- * Refresh clock Prescalar
- */
-#define CONFIG_SYS_MPTPR	MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 |	\
-			 MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
-
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-/* Configuration variable added by yooth. */
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-
-/*
- * BCSRx
- *
- * Board Status and Control Registers
- *
- */
-
-#define BCSR0 0xFA400000
-#define BCSR1 0xFA400001
-#define BCSR2 0xFA400002
-#define BCSR3 0xFA400003
-
-#define BCSR0_ENMONXCVR	0x01	/* Monitor XVCR Control */
-#define BCSR0_ENNVRAM	0x02	/* CS4# Control */
-#define BCSR0_LED5		0x04	/* LED5 control 0='on' 1='off' */
-#define BCSR0_LED4		0x08	/* LED4 control 0='on' 1='off' */
-#define BCSR0_FULLDPLX	0x10	/* Ethernet XCVR Control */
-#define BCSR0_COLTEST	0x20
-#define BCSR0_ETHLPBK	0x40
-#define BCSR0_ETHEN	0x80
-
-#define BCSR1_PCVCTL7	0x01	/* PC Slot B Control */
-#define BCSR1_PCVCTL6	0x02
-#define BCSR1_PCVCTL5	0x04
-#define BCSR1_PCVCTL4	0x08
-#define BCSR1_IPB5SEL	0x10
-
-#define BCSR2_MIIRST    0x80
-#define BCSR2_MIIPWRDWN 0x40
-#define BCSR2_MIICTL    0x08
-
-#define BCSR3_BWRTC		0x01	/* Real Time Clock Battery */
-#define BCSR3_BWNVR		0x02	/* NVRAM Battery */
-#define BCSR3_RDY_BSY	0x04	/* Flash Operation */
-#define BCSR3_RPXL		0x08	/* Reserved (reads back '1') */
-#define BCSR3_D27		0x10	/* Dip Switch settings */
-#define BCSR3_D26		0x20
-#define BCSR3_D25		0x40
-#define BCSR3_D24		0x80
-
-
-/*
- * Environment setting
- */
-
-/* #define CONFIG_ETHADDR	00:10:EC:00:2C:A2 */
-/* #define CONFIG_IPADDR	10.10.106.1 */
-/* #define CONFIG_SERVERIP	10.10.104.11 */
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/RPXlite.h b/include/configs/RPXlite.h
deleted file mode 100644
index a28230a..0000000
--- a/include/configs/RPXlite.h
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
- * U-Boot port on RPXlite board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	RPXLite_50MHz
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#undef CONFIG_MPC860
-#define CONFIG_MPC850		1	/* This is a MPC850 CPU		*/
-#define CONFIG_RPXLITE		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff00000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600	/* console baudrate = 9600bps	*/
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"bootp; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#define CONFIG_BZIP2		/* Include support for bzip2 compressed images  */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	40000	/* 40 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-/* Software (bit-bang) I2C driver configuration */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if (bit) \
-				immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else \
-				immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if (bit) \
-				immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else \
-				immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-/* M41T11 Serial Access Timekeeper(R) SRAM */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-/* play along with the linux driver */
-#define CONFIG_SYS_M41T11_BASE_YEAR 1900
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_RESET_ADDRESS	0x09900000
-
-#define	CONFIG_SYS_LOAD_ADDR		0x400000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFA200000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFFC00000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#ifdef CONFIG_BZIP2
-#define CONFIG_SYS_MALLOC_LEN		(4096 << 10)	/* Reserve ~4 MB for malloc()   */
-#else
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 KB for malloc()  */
-#endif /* CONFIG_BZIP2 */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	19	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_SYS_DIRECT_FLASH_TFTP
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SECT_SIZE	0x40000	/* We use one complete sector		*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-
-#define CONFIG_ENV_OVERWRITE
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_MLRC10)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-/*%%%#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_PLPRCR	( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF00
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_SCCR	(SCCR_COM11 | SCCR_TBS)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define	CONFIG_SYS_DER	0x2002000F*/
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE_PRELIM	0xFE000000	/* FLASH base */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFE000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
-
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
-
-/*
- * BR1 and OR1 (SDRAM)
- *
- */
-#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM base	*/
-#define	SDRAM_MAX_SIZE		0x01000000	/* max 16 MB */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000E00
-
-#define CONFIG_SYS_OR1_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR1_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/* RPXLITE mem setting */
-#define	CONFIG_SYS_BR3_PRELIM	0xFA400001		/* BCSR */
-#define CONFIG_SYS_OR3_PRELIM	0xFFFF8910
-#define	CONFIG_SYS_BR4_PRELIM	0xFA000401		/* NVRAM&SRAM */
-#define CONFIG_SYS_OR4_PRELIM	0xFFFE0970
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA	58
-
-/*
- * Refresh clock Prescalar
- */
-#define CONFIG_SYS_MPTPR	MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 |	\
-			 MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
-
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-/* Configuration variable added by yooth. */
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-
-/*
- * BCSRx
- *
- * Board Status and Control Registers
- *
- */
-
-#define BCSR0 0xFA400000
-#define BCSR1 0xFA400001
-#define BCSR2 0xFA400002
-#define BCSR3 0xFA400003
-
-#define BCSR0_ENMONXCVR	0x01	/* Monitor XVCR Control */
-#define BCSR0_ENNVRAM	0x02	/* CS4# Control */
-#define BCSR0_LED5	0x04	/* LED5 control 0='on' 1='off' */
-#define BCSR0_LED4	0x08	/* LED4 control 0='on' 1='off' */
-#define BCSR0_FULLDPLX	0x10	/* Ethernet XCVR Control */
-#define BCSR0_COLTEST	0x20
-#define BCSR0_ETHLPBK	0x40
-#define BCSR0_ETHEN	0x80
-
-#define BCSR1_PCVCTL7	0x01	/* PC Slot B Control */
-#define BCSR1_PCVCTL6	0x02
-#define BCSR1_PCVCTL5	0x04
-#define BCSR1_PCVCTL4	0x08
-#define BCSR1_IPB5SEL	0x10
-
-#define BCSR2_ENPA5HDR	0x08	/* USB Control */
-#define BCSR2_ENUSBCLK	0x10
-#define BCSR2_USBPWREN	0x20
-#define BCSR2_USBSPD	0x40
-#define BCSR2_USBSUSP	0x80
-
-#define BCSR3_BWRTC	0x01	/* Real Time Clock Battery */
-#define BCSR3_BWNVR	0x02	/* NVRAM Battery */
-#define BCSR3_RDY_BSY	0x04	/* Flash Operation */
-#define BCSR3_RPXL	0x08	/* Reserved (reads back '1') */
-#define BCSR3_D27	0x10	/* Dip Switch settings */
-#define BCSR3_D26	0x20
-#define BCSR3_D25	0x40
-#define BCSR3_D24	0x80
-
-#endif	/* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 1ad3e63..952a67c 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -22,7 +22,7 @@
 #if !defined(CONFIG_PCMCIA_SLOT_A) && !defined(CONFIG_PCMCIA_SLOT_B)
 
 					/* The RPX series use SLOT_B	*/
-#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
+#if defined(CONFIG_RPXLITE)
 # define CONFIG_PCMCIA_SLOT_B
 #elif defined(CONFIG_FADS)		/* The FADS series are a mess	*/
 # if defined(CONFIG_MPC86x) || defined(CONFIG_MPC821)