powerpc/mpc85xx: Remove P1023 RDS support

Since P1023RDS is no longer supported/manufactured by Freescale,
we clean up P1023RDS related code.
Since P1023RDB is still supported by Freescale,
we keep P1023RDB releated code.

Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

1 files changed, 0 insertions, 479 deletions

diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h
deleted file mode 100644
index ac75b9c..0000000
--- a/include/configs/P1023RDS.h
+++ /dev/null
@@ -1,479 +0,0 @@
-/*
- * Copyright 2010-2012 Freescale Semiconductor, Inc.
- *
- * Authors:  Roy Zang <tie-fei.zang@freescale.com>
- *	     Chunhe Lan <b25806@freescale.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * p1023rds board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xeff40000
-#endif
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE		/* BOOKE */
-#define CONFIG_E500		/* BOOKE e500 family */
-#define CONFIG_P1023
-#define CONFIG_P1023RDS
-#define CONFIG_MP		/* support multiple processors */
-
-#define CONFIG_FSL_ELBC		/* Has Enhanced localbus controller */
-#define CONFIG_PCI		/* Enable PCI/PCIE */
-#define CONFIG_PCIE1		/* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2		/* PCIE controler 2 (slot 2) */
-#define CONFIG_PCIE3		/* PCIE controler 3 (slot 3) */
-#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
-#define CONFIG_FSL_LAW		/* Use common FSL init code */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	66666666
-#define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-#define CONFIG_HWCONFIG
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x1fffffff	/* fix me, only 1G */
-#define CONFIG_PANIC_HANG	/* do not reset board on panic */
-
-#define CONFIG_SYS_LBC_LBCR	0x00000000	/* Implement conversion of
-						addresses in the LBC */
-
-/* DDR Setup */
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	2
-
-/* These are used when DDR doesn't use SPD.  */
-#define CONFIG_SYS_SDRAM_SIZE		2048u	/* DDR is 2GB */
-
-/* Default settings for "stable" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000003F
-#define CONFIG_SYS_DDR_CS1_BNDS		0x0040007F
-#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014302
-#define CONFIG_SYS_DDR_CS1_CONFIG	0x80014302
-#define CONFIG_SYS_DDR_TIMING_3		0x00020000
-#define CONFIG_SYS_DDR_TIMING_0		0x40110104
-#define CONFIG_SYS_DDR_TIMING_1		0x5C59E544
-#define CONFIG_SYS_DDR_TIMING_2		0x0fA888CA
-#define CONFIG_SYS_DDR_MODE_1		0x00441210
-#define CONFIG_SYS_DDR_MODE_2		0x00000000
-#define CONFIG_SYS_DDR_MODE_CTRL	0x00000000
-#define CONFIG_SYS_DDR_INTERVAL		0x0A280100
-#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL		0x01800000
-#define CONFIG_SYS_DDR_TIMING_4		0x00000001
-#define CONFIG_SYS_DDR_TIMING_5		0x01401400
-#define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
-#define CONFIG_SYS_DDR_WRLVL_CNTL	0x8675F605
-#define CONFIG_SYS_DDR_CONTROL	0xC70C0008 /* Type = DDR3: No Interleaving */
-#define CONFIG_SYS_DDR_CONTROL2		0x24401010
-#define CONFIG_SYS_DDR_CDR1		0x00000000
-#define CONFIG_SYS_DDR_CDR2		0x00000000
-
-#define CONFIG_SYS_DDR_ERR_INT_EN	0x00000000
-#define CONFIG_SYS_DDR_ERR_DIS		0x00000000
-#define CONFIG_SYS_DDR_SBE		0x00000000
-
-/* Settings that differ for "performance" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS_PERF	0x0000007F /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_BNDS_PERF	0x00000000 /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_CONFIG_PERF	0x80014302
-#define CONFIG_SYS_DDR_TIMING_1_PERF	0x5C58E544
-#define CONFIG_SYS_DDR_TIMING_2_PERF	0x0FA888CA
-/* Type = DDR3: cs0-cs1 interleaving */
-#define CONFIG_SYS_DDR_CONTROL_PERF	0xC70C4008
-#define CONFIG_SYS_DDR_CDR_1		0x00000000
-#define CONFIG_SYS_DDR_CDR_2		0x00000000
-
-
-/*
- * Memory map
- *
- * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
- * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
- * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
- * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
- *
- * Localbus non-cacheable
- * 0xe000_0000	0xe003_ffff	BCSR			256K BCSR
- * 0xee00_0000	0xefff_ffff	NOR flash		32M NOR flash
- * 0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M
- * 0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
- * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
- * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_BCSR_BASE		0xe0000000 /* start of on board FPGA */
-#define CONFIG_SYS_BCSR_BASE_PHYS	CONFIG_SYS_BCSR_BASE
-
-#define CONFIG_SYS_FLASH_BASE		0xee000000 /* start of FLASH 32M */
-
-#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
-		| BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM	0xfe000ff7
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#if defined(CONFIG_SYS_SPL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F	/* call board_early_init_f function */
-#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_END	0x00004000	/* End of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-	(CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */
-
-#ifndef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE		0xffa00000
-#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
-#else
-#define CONFIG_SYS_NAND_BASE		0xfff00000
-#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
-#endif
-
-#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE}
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 * 1024)
-
-/* NAND boot: 4K NAND loader config */
-#define CONFIG_SYS_NAND_SPL_SIZE	0x1000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	((768 << 10) + CONFIG_SYS_NAND_SPL_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_DST	(0x11000000 - CONFIG_SYS_NAND_SPL_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_START	0x11000000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(0)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC	0x00010000
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP	(CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
-				| BR_PS_8		/* Port Size = 8bit */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM  (0xFFF80000		/* length 32K */ \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-
-#define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM  CONFIG_FLASH_OR_PRELIM	/* NOR Options */
-/* chip select 1 - BCSR */
-#define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
-				| BR_MS_GPCM | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR1_PRELIM  (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
-				| OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
-				| OR_GPCM_EAD)
-
-/* Serial Port
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX		1
-#undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x51
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x51
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-#define CONFIG_SYS_EEPROM_BUS_NUM	0
-
-#define CONFIG_CMD_I2C
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_ATMEL
-
-#define CONFIG_HARD_SPI
-#define CONFIG_FSL_ESPI
-
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED		10000000
-#define CONFIG_SF_DEFAULT_MODE		0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 3, Slot 1, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME		"Slot 3"
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
-#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 2, direct to uli, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME		"Slot 2"
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 1, Slot 2, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME		"Slot 1"
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-#if defined(CONFIG_PCI)
-#define CONFIG_E1000		/* Defind e1000 pci Ethernet card */
-#define CONFIG_PCI_PNP		/* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#endif	/* CONFIG_PCI */
-
-/*
- * Environment
- */
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x4000)
-#define CONFIG_ENV_SIZE		0x2000
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_LOADS_ECHO		/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#endif
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(16 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_UBOOTPATH	(u-boot.bin) /* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		1000000
-
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE	115200
-
-/* Qman/Bman */
-#define CONFIG_SYS_DPAA_QBMAN		/* support Q/Bman */
-#define CONFIG_SYS_QMAN_MEM_BASE	0xff000000
-#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
-#define CONFIG_SYS_BMAN_MEM_BASE	0xff200000
-#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
-
-/* For FM */
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHY_MARVELL
-#endif
-
-/* Default address of microcode for the Linux Fman driver */
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x2
-#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x7
-
-#define CONFIG_SYS_TBIPA_VALUE	8
-#define CONFIG_MII		/* MII PHY management */
-#define CONFIG_ETHPRIME		"FM1@DTSEC1"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS	\
-	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
-
-#endif	/* __CONFIG_H */