powerpc/b4860qds: Added Support for B4860QDS

B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
  ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,  ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
  16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
  8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
  RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
  connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
  connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
  configuration reset source. The RCW source is set by appropriate
  DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
	- On-board eCWTAP controller with ETH and USB I/F
	- JTAG/COP 16-pin header for any external TAP controller
	- External JTAG source over AMC to support B2B configuration
	- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
	- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
  DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
  - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

1 files changed, 820 insertions, 0 deletions

diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
new file mode 100644
index 0000000..b09119a
--- /dev/null
+++ b/include/configs/B4860QDS.h
@@ -0,0 +1,820 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * B4860 QDS board configuration file
+ */
+#define CONFIG_B4860QDS
+#define CONFIG_PHYS_64BIT
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E6500
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_E500MC			/* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
+#define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
+#define CONFIG_MP			/* support multiple processors */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC			/* Enable IFC Support */
+#define CONFIG_PCI			/* Enable PCI/PCIE */
+#define CONFIG_PCIE1			/* PCIE controler 1 */
+#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
+
+#ifndef CONFIG_PPC_B4420
+#define CONFIG_SYS_SRIO
+#define CONFIG_SRIO1			/* SRIO port 1 */
+#define CONFIG_SRIO2			/* SRIO port 2 */
+#endif
+
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+
+/* I2C bus multiplexer */
+#define I2C_MUX_PCA_ADDR                0x77
+
+/* VSC Crossbar switches */
+#define CONFIG_VSC_CROSSBAR
+#define I2C_CH_DEFAULT                  0x8
+#define I2C_CH_VSC3316                  0xc
+#define I2C_CH_VSC3308                  0xd
+
+#define VSC3316_TX_ADDRESS              0x70
+#define VSC3316_RX_ADDRESS              0x71
+#define VSC3308_TX_ADDRESS              0x02
+#define VSC3308_RX_ADDRESS              0x03
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS              0
+#define CONFIG_ENV_SPI_CS               0
+#define CONFIG_ENV_SPI_MAX_HZ           10000000
+#define CONFIG_ENV_SPI_MODE             0
+#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE            0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV          0
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(512 * 1097)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+#else /* CONFIG_SYS_NO_FLASH */
+#define CONFIG_ENV_SIZE                0x2000
+#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk() /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
+#endif
+
+#if 0
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY	/* test POST memory test */
+#endif
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ *  Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR		0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_FSL_DDR3
+#define CONFIG_FSL_DDR_INTERACTIVE
+
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define SPD_EEPROM_ADDRESS1	0x51
+#define SPD_EEPROM_ADDRESS2	0x53
+
+#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
+#define CONFIG_SYS_SDRAM_SIZE	2048	/* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE	0xe0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+				+ 0x8000000) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128 * 1024 * 1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(4)
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x01) | \
+				FTIM0_NOR_TEADC(0x01) | \
+				FTIM0_NOR_TEAHC(0x20))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1A) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x01) | \
+				FTIM2_NOR_TCH(0x0E) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \
+					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
+#define CONFIG_FSL_QIXIS_V2
+#define QIXIS_BASE		0xffdf0000
+#ifdef CONFIG_PHYS_64BIT
+#define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)
+#else
+#define QIXIS_BASE_PHYS		QIXIS_BASE
+#endif
+#define QIXIS_LBMAP_SWITCH		0x01
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SHIFT		0
+#define QIXIS_LBMAP_DFLTBANK		0x00
+#define QIXIS_LBMAP_ALTBANK		0x02
+#define QIXIS_RST_CTL_RESET		0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+
+#define CONFIG_SYS_CSPR3_EXT	(0xf)
+#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK3	IFC_AMASK(4 * 1024)
+#define CONFIG_SYS_CSOR3	0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
+					FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3		0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
+				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
+#endif
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	0xfe0ec000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed in Hz */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x118000
+#define CONFIG_SYS_I2C2_OFFSET		0x119000
+
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS3231               1
+#define CONFIG_SYS_I2C_RTC_ADDR         0x68
+
+/*
+ * RapidIO
+ */
+#ifdef CONFIG_SYS_SRIO
+#ifdef CONFIG_SRIO1
+#define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_SRIO1_MEM_PHYS	0xa0000000
+#endif
+#define CONFIG_SYS_SRIO1_MEM_SIZE	0x10000000	/* 256M */
+#endif
+
+#ifdef CONFIG_SRIO2
+#define CONFIG_SYS_SRIO2_MEM_VIRT	0xb0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
+#else
+#define CONFIG_SYS_SRIO2_MEM_PHYS	0xb0000000
+#endif
+#define CONFIG_SYS_SRIO2_MEM_SIZE	0x10000000	/* 256M */
+#endif
+#endif
+
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000	/* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000	/* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED         10000000
+#define CONFIG_SF_DEFAULT_MODE          0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	25
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	25
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_TERANETICS
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x10
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x11
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif	/* CONFIG_PCI */
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR	0x10
+#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR	0x11
+#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR	4
+
+#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
+#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
+#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
+#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
+
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC1"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	"u-boot.bin"	/* U-Boot image on TFTP server*/
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE	115200
+
+#define __USB_PHY_TYPE	ulpi
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:ctlr_intlv=null,"		\
+	"bank_intlv=cs0_cs1;"					\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"			\
+	"tftpflash=tftpboot $loadaddr $uboot && "		\
+	"protect off $ubootaddr +$filesize && "			\
+	"erase $ubootaddr +$filesize && "			\
+	"cp.b $loadaddr $ubootaddr $filesize && "		\
+	"protect on $ubootaddr +$filesize && "			\
+	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=b4860qds/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=b4860qds/b4860qds.dtb\0"				\
+	"bdev=sda3\0"						\
+	"c=ffe\0"
+
+/* For emulation this causes u-boot to jump to the start of the proof point
+   app code automatically */
+#define CONFIG_PROOF_POINTS			\
+ "setenv bootargs root=/dev/$bdev rw "		\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "cpu 1 release 0x29000000 - - -;"		\
+ "cpu 2 release 0x29000000 - - -;"		\
+ "cpu 3 release 0x29000000 - - -;"		\
+ "cpu 4 release 0x29000000 - - -;"		\
+ "cpu 5 release 0x29000000 - - -;"		\
+ "cpu 6 release 0x29000000 - - -;"		\
+ "cpu 7 release 0x29000000 - - -;"		\
+ "go 0x29000000"
+
+#define CONFIG_HVBOOT	\
+ "setenv bootargs config-addr=0x60000000; "	\
+ "bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU				\
+ "setenv bootargs root=/dev/$bdev rw "		\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "cpu 1 release 0x01000000 - - -;"		\
+ "cpu 2 release 0x01000000 - - -;"		\
+ "cpu 3 release 0x01000000 - - -;"		\
+ "cpu 4 release 0x01000000 - - -;"		\
+ "cpu 5 release 0x01000000 - - -;"		\
+ "cpu 6 release 0x01000000 - - -;"		\
+ "cpu 7 release 0x01000000 - - -;"		\
+ "go 0x01000000"
+
+#define CONFIG_LINUX				\
+ "setenv bootargs root=/dev/ram rw "		\
+ "console=$consoledev,$baudrate $othbootargs;"	\
+ "setenv ramdiskaddr 0x02000000;"		\
+ "setenv fdtaddr 0x00c00000;"			\
+ "setenv loadaddr 0x1000000;"			\
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT					\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif	/* __CONFIG_H */