Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'

5 files changed, 0 insertions, 1063 deletions

diff --git a/include/configs/actux1.h b/include/configs/actux1.h
deleted file mode 100644
index 9b8bd78..0000000
--- a/include/configs/actux1.h
+++ /dev/null
@@ -1,226 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * Configuration settings for the AcTux-1 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_IXP425			1
-#define CONFIG_ACTUX1			1
-
-#define	CONFIG_MACH_TYPE		1479
-
-#define CONFIG_DISPLAY_CPUINFO		1
-#define CONFIG_DISPLAY_BOARDINFO	1
-
-#define CONFIG_IXP_SERIAL
-#define CONFIG_SYS_IXP425_CONSOLE		IXP425_UART2
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTDELAY		3
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_BOARD_EARLY_INIT_F	1
-#define CONFIG_SYS_LDSCRIPT	"board/actux1/u-boot.lds"
-
-/***************************************************************
- * U-boot generic defines start here.
- ***************************************************************/
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Command line configuration. */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_PCI_PNP
-#define CONFIG_IXP_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_CMD_PCI_ENUM
-#endif
-
-#define CONFIG_BOOTCOMMAND		"run boot_flash"
-/* enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG		1
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-#define CONFIG_REVISION_TAG		1
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_KGDB_BAUDRATE		230400
-#endif
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE			256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS			16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE			CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START		0x00400000
-#define CONFIG_SYS_MEMTEST_END			0x00800000
-
-/* timer clock - 2* OSC_IN system clock */
-#define CONFIG_IXP425_TIMER_CLK                 66666666
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR			0x00010000
-
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600,	\
-					  115200, 230400 }
-#define CONFIG_SERIAL_RTS_ACTIVE	1
-
-/* Expansion bus settings */
-#define CONFIG_SYS_EXP_CS0			0xbd113842
-
-/* SDRAM settings */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_SDRAM_BASE			0x00000000
-
-#ifdef CONFIG_RAM_32MB
-# define CONFIG_SYS_SDR_CONFIG			0x18
-# define PHYS_SDRAM_1_SIZE		0x02000000
-# define CONFIG_SYS_SDRAM_REFRESH_CNT		0x81a
-# define CONFIG_SYS_SDR_MODE_CONFIG		0x1
-# define CONFIG_SYS_DRAM_SIZE			0x02000000
-#else /* 16MB SDRAM */
-# define CONFIG_SYS_SDR_CONFIG			0x3A
-# define PHYS_SDRAM_1_SIZE		0x01000000
-# define CONFIG_SYS_SDRAM_REFRESH_CNT		0x81a
-# define CONFIG_SYS_SDR_MODE_CONFIG		0x1
-# define CONFIG_SYS_DRAM_SIZE			0x01000000
-#endif
-
-/* FLASH organization */
-#define CONFIG_SYS_TEXT_BASE		0x50000000
-#ifdef CONFIG_FLASH2X2
-# define CONFIG_SYS_MAX_FLASH_BANKS		2
-/* max number of sectors on one chip */
-# define CONFIG_SYS_MAX_FLASH_SECT		40
-# define PHYS_FLASH_1			0x50000000
-# define PHYS_FLASH_2			0x50200000
-# define CONFIG_SYS_FLASH_BANKS_LIST		{ PHYS_FLASH_1, PHYS_FLASH_2 }
-#endif
-#ifdef CONFIG_FLASH1X8
-# define CONFIG_SYS_MAX_FLASH_BANKS		1
-/* max number of sectors on one chip */
-# define CONFIG_SYS_MAX_FLASH_SECT		140
-# define PHYS_FLASH_1			0x50000000
-# define CONFIG_SYS_FLASH_BANKS_LIST		{ PHYS_FLASH_1 }
-#endif
-
-#define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN			(256 << 10)
-#define CONFIG_BOARD_SIZE_LIMIT			262144
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* no byte writes on IXP4xx */
-#define CONFIG_SYS_FLASH_CFI_WIDTH		FLASH_CFI_16BIT
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* Ethernet */
-
-/* include IXP4xx NPE support */
-#define CONFIG_IXP4XX_NPE		1
-/* NPE0 PHY address */
-#define	CONFIG_PHY_ADDR			0
-/* NPE1 PHY address (HW Release E only) */
-#define	CONFIG_PHY1_ADDR		1
-/* MII PHY management */
-#define CONFIG_MII			1
-/* Number of ethernet rx buffers & descriptors */
-#define CONFIG_SYS_RX_ETH_BUFFER		16
-#define CONFIG_RESET_PHY_R		1
-
-#define CONFIG_HAS_ETH1			1
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#undef  CONFIG_CMD_NFS
-
-/* BOOTP options */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE		32
-
-/*
- * environment organization:
- * one flash sector, embedded in uboot area (bottom bootblock flash)
- */
-#define	CONFIG_ENV_IS_IN_FLASH		1
-#define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_ADDR			(PHYS_FLASH_1 + 0x4000)
-#define CONFIG_SYS_USE_PPCENV			1
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"npe_ucode=50040000\0"						\
-	"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
-	"kerneladdr=50050000\0"						\
-	"kernelfile=actux1/uImage\0"					\
-	"rootfile=actux1/rootfs\0"					\
-	"rootaddr=50170000\0"						\
-	"loadaddr=10000\0"						\
-	"updateboot_ser=mw.b 10000 ff 40000;"				\
-	" loady ${loadaddr};"						\
-	" run eraseboot writeboot\0"					\
-	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} actux1/u-boot.bin;"				\
-	" run eraseboot writeboot\0"					\
-	"eraseboot=protect off 50000000 50003fff;"			\
-	" protect off 50006000 5003ffff;"				\
-	" erase 50000000 50003fff;"					\
-	" erase 50006000 5003ffff\0"					\
-	"writeboot=cp.b 10000 50000000 4000;"				\
-	" cp.b 16000 50006000 3a000\0"					\
-	"updateucode=loady;"						\
-	" era ${npe_ucode} +${filesize};"				\
-	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
-	"updateroot=tftp ${loadaddr} ${rootfile};"			\
-	" era ${rootaddr} +${filesize};"				\
-	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\
-	"updatekern=tftp ${loadaddr} ${kernelfile};"			\
-	" era ${kerneladdr} +${filesize};"				\
-	" cp.b ${loadaddr} ${kerneladdr} ${filesize}\0"			\
-	"flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \
-	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"	\
-	"boot_flash=run flashargs addtty addeth;"			\
-	" bootm ${kerneladdr}\0"					\
-	"boot_net=run netargs addtty addeth;"				\
-	" tftpboot ${loadaddr} ${kernelfile};"				\
-	" bootm\0"
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_INIT_SP_ADDR						\
-	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/actux2.h b/include/configs/actux2.h
deleted file mode 100644
index f0cbff7..0000000
--- a/include/configs/actux2.h
+++ /dev/null
@@ -1,206 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * Configuration settings for the AcTux-2 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_IXP425			1
-#define CONFIG_ACTUX2			1
-
-#define	CONFIG_MACH_TYPE		1480
-
-#define CONFIG_DISPLAY_CPUINFO		1
-#define CONFIG_DISPLAY_BOARDINFO	1
-
-#define CONFIG_IXP_SERIAL
-#define CONFIG_SYS_IXP425_CONSOLE		IXP425_UART2
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTDELAY		5
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_BOARD_EARLY_INIT_F	1
-#define CONFIG_SYS_LDSCRIPT	"board/actux2/u-boot.lds"
-
-/***************************************************************
- * U-boot generic defines start here.
- ***************************************************************/
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Command line configuration. */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#undef CONFIG_CMD_PCI
-#undef CONFIG_PCI
-
-#define CONFIG_BOOTCOMMAND		"run boot_flash"
-/* enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG		1
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-#define CONFIG_REVISION_TAG		1
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_KGDB_BAUDRATE		230400
-#endif
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE			256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS			16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE			CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START		0x00400000
-#define CONFIG_SYS_MEMTEST_END			0x00800000
-
-/* timer clock - 2* OSC_IN system clock */
-#define CONFIG_IXP425_TIMER_CLK                 66666666
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR			0x00010000
-
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, \
-					  115200, 230400 }
-#define CONFIG_SERIAL_RTS_ACTIVE	1
-
-/* Expansion bus settings */
-#define CONFIG_SYS_EXP_CS0			0xbd113042
-
-/* SDRAM settings */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_SDRAM_BASE			0x00000000
-
-/* 16MB SDRAM */
-#define CONFIG_SYS_SDR_CONFIG			0x3A
-#define PHYS_SDRAM_1_SIZE		0x01000000
-#define CONFIG_SYS_SDRAM_REFRESH_CNT		0x81a
-#define CONFIG_SYS_SDR_MODE_CONFIG		0x1
-#define CONFIG_SYS_DRAM_SIZE			0x01000000
-
-/* FLASH organization */
-#define CONFIG_SYS_TEXT_BASE		0x50000000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-/* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_SECT		140
-#define PHYS_FLASH_1			0x50000000
-#define CONFIG_SYS_FLASH_BANKS_LIST		{ PHYS_FLASH_1 }
-
-#define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN			(256 << 10)
-#define CONFIG_BOARD_SIZE_LIMIT			262144
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* no byte writes on IXP4xx */
-#define CONFIG_SYS_FLASH_CFI_WIDTH		FLASH_CFI_16BIT
-
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* Ethernet */
-
-/* include IXP4xx NPE support */
-#define CONFIG_IXP4XX_NPE		1
-/* NPE0 PHY address */
-#define	CONFIG_PHY_ADDR			0x00
-/* MII PHY management */
-#define CONFIG_MII			1
-/* fixed-speed switch without standard PHY registers on MII */
-#define CONFIG_MII_NPE0_FIXEDLINK       1
-#define CONFIG_MII_NPE0_SPEED           100
-#define CONFIG_MII_NPE0_FULLDUPLEX      1
-
-/* Number of ethernet rx buffers & descriptors */
-#define CONFIG_SYS_RX_ETH_BUFFER		16
-#define CONFIG_RESET_PHY_R		1
-/* ethernet switch connected to MII port */
-#define CONFIG_MII_ETHSWITCH		1
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#undef  CONFIG_CMD_NFS
-
-/* BOOTP options */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE		32
-
-/*
- * environment organization:
- * one flash sector, embedded in uboot area (bottom bootblock flash)
- */
-#define	CONFIG_ENV_IS_IN_FLASH		1
-#define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_ADDR			(PHYS_FLASH_1 + 0x4000)
-#define CONFIG_SYS_USE_PPCENV			1
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"npe_ucode=50040000\0"						\
-	"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
-	"kerneladdr=50050000\0"						\
-	"kernelfile=actux2/uImage\0"					\
-	"rootfile=actux2/rootfs\0"					\
-	"rootaddr=50170000\0"						\
-	"loadaddr=10000\0"						\
-	"updateboot_ser=mw.b 10000 ff 40000;"				\
-	" loady ${loadaddr};"						\
-	" run eraseboot writeboot\0"					\
-	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} actux2/u-boot.bin;"				\
-	" run eraseboot writeboot\0"					\
-	"eraseboot=protect off 50000000 50003fff;"			\
-	" protect off 50006000 5003ffff;"				\
-	" erase 50000000 50003fff;"					\
-	" erase 50006000 5003ffff\0"					\
-	"writeboot=cp.b 10000 50000000 4000;"				\
-	" cp.b 16000 50006000 3a000\0"					\
-	"updateucode=loady;"						\
-	" era ${npe_ucode} +${filesize};"				\
-	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
-	"updateroot=tftp ${loadaddr} ${rootfile};"			\
-	" era ${rootaddr} +${filesize};"				\
-	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\
-	"updatekern=tftp ${loadaddr} ${kernelfile};"			\
-	" era ${kerneladdr} +${filesize};"				\
-	" cp.b ${loadaddr} ${kerneladdr} ${filesize}\0"			\
-	"flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
-	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"	\
-	"boot_flash=run flashargs addtty addeth;"			\
-	" bootm ${kerneladdr}\0"					\
-	"boot_net=run netargs addtty addeth;"				\
-	" tftpboot ${loadaddr} ${kernelfile};"				\
-	" bootm\0"
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_INIT_SP_ADDR						\
-	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/actux3.h b/include/configs/actux3.h
deleted file mode 100644
index 7639107..0000000
--- a/include/configs/actux3.h
+++ /dev/null
@@ -1,205 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * Configuration settings for the AcTux-3 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_IXP425			1
-#define CONFIG_ACTUX3			1
-
-#define	CONFIG_MACH_TYPE		1481
-
-#define CONFIG_DISPLAY_CPUINFO		1
-#define CONFIG_DISPLAY_BOARDINFO	1
-
-#define CONFIG_IXP_SERIAL
-#define CONFIG_SYS_IXP425_CONSOLE		IXP425_UART2
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTDELAY		3
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_BOARD_EARLY_INIT_F	1
-#define CONFIG_SYS_LDSCRIPT	"board/actux3/u-boot.lds"
-
-/***************************************************************
- * U-boot generic defines start here.
- ***************************************************************/
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Command line configuration. */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-
-#define CONFIG_BOOTCOMMAND		"run boot_flash"
-/* enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG		1
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-#define CONFIG_REVISION_TAG		1
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_KGDB_BAUDRATE		230400
-#endif
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE			256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS			16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE			CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START		0x00400000
-#define CONFIG_SYS_MEMTEST_END			0x00800000
-
-/* timer clock - 2* OSC_IN system clock */
-#define CONFIG_IXP425_TIMER_CLK                 66666666
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR			0x00010000
-
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, \
-					  115200, 230400 }
-#define CONFIG_SERIAL_RTS_ACTIVE	1
-
-/* Expansion bus settings */
-#define CONFIG_SYS_EXP_CS0			0xbd113442
-
-/* SDRAM settings */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_SDRAM_BASE			0x00000000
-
-/* 16MB SDRAM */
-#define CONFIG_SYS_SDR_CONFIG			0x3A
-#define PHYS_SDRAM_1_SIZE		0x01000000
-#define CONFIG_SYS_SDRAM_REFRESH_CNT		0x81a
-#define CONFIG_SYS_SDR_MODE_CONFIG		0x1
-#define CONFIG_SYS_DRAM_SIZE			0x01000000
-
-/* FLASH organization */
-#define CONFIG_SYS_TEXT_BASE		0x50000000
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-/* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_SECT		140
-#define PHYS_FLASH_1			0x50000000
-#define CONFIG_SYS_FLASH_BANKS_LIST		{ PHYS_FLASH_1 }
-
-#define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN			(256 << 10)
-#define CONFIG_BOARD_SIZE_LIMIT			262144
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* no byte writes on IXP4xx */
-#define CONFIG_SYS_FLASH_CFI_WIDTH		FLASH_CFI_16BIT
-
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* Ethernet */
-
-/* include IXP4xx NPE support */
-#define CONFIG_IXP4XX_NPE		1
-
-/* NPE0 PHY address */
-#define	CONFIG_PHY_ADDR			0x10
-/* MII PHY management */
-#define CONFIG_MII			1
-/* fixed-speed switch without standard PHY registers on MII */
-#define CONFIG_MII_NPE0_FIXEDLINK       1
-#define CONFIG_MII_NPE0_SPEED           100
-#define CONFIG_MII_NPE0_FULLDUPLEX      1
-
-/* Number of ethernet rx buffers & descriptors */
-#define CONFIG_SYS_RX_ETH_BUFFER		16
-#define CONFIG_RESET_PHY_R		1
-/* ethernet switch connected to MII port */
-#define CONFIG_MII_ETHSWITCH		1
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#undef  CONFIG_CMD_NFS
-
-/* BOOTP options */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE		32
-
-/*
- * environment organization:
- * one flash sector, embedded in uboot area (bottom bootblock flash)
- */
-#define	CONFIG_ENV_IS_IN_FLASH		1
-#define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_ADDR			(PHYS_FLASH_1 + 0x4000)
-#define CONFIG_SYS_USE_PPCENV			1
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"npe_ucode=50040000\0"						\
-	"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
-	"kerneladdr=50050000\0"						\
-	"kernelfile=actux3/uImage\0"					\
-	"rootfile=actux3/rootfs\0"					\
-	"rootaddr=50170000\0"						\
-	"loadaddr=10000\0"						\
-	"updateboot_ser=mw.b 10000 ff 40000;"				\
-	" loady ${loadaddr};"						\
-	" run eraseboot writeboot\0"					\
-	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} actux3/u-boot.bin;"				\
-	" run eraseboot writeboot\0"					\
-	"eraseboot=protect off 50000000 50003fff;"			\
-	" protect off 50006000 5003ffff;"				\
-	" erase 50000000 50003fff;"					\
-	" erase 50006000 5003ffff\0"					\
-	"writeboot=cp.b 10000 50000000 4000;"				\
-	" cp.b 16000 50006000 3a000\0"					\
-	"updateucode=loady;"						\
-	" era ${npe_ucode} +${filesize};"				\
-	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
-	"updateroot=tftp ${loadaddr} ${rootfile};"			\
-	" era ${rootaddr} +${filesize};"				\
-	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\
-	"updatekern=tftp ${loadaddr} ${kernelfile};"			\
-	" era ${kerneladdr} +${filesize};"				\
-	" cp.b ${loadaddr} ${kerneladdr} ${filesize}\0"			\
-	"flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \
-	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"	\
-	"boot_flash=run flashargs addtty addeth;"			\
-	" bootm ${kerneladdr}\0"					\
-	"boot_net=run netargs addtty addeth;"				\
-	" tftpboot ${loadaddr} ${kernelfile};"				\
-	" bootm\0"
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_INIT_SP_ADDR						\
-	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/actux4.h b/include/configs/actux4.h
deleted file mode 100644
index 12bd98a..0000000
--- a/include/configs/actux4.h
+++ /dev/null
@@ -1,204 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * Configuration settings for the AcTux-4 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_IXP425			1
-#define CONFIG_ACTUX4			1
-
-#define	CONFIG_MACH_TYPE		1532
-
-#define CONFIG_DISPLAY_CPUINFO		1
-#define CONFIG_DISPLAY_BOARDINFO	1
-
-#define CONFIG_IXP_SERIAL
-#define CONFIG_SYS_IXP425_CONSOLE		IXP425_UART1
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTDELAY		3
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_BOARD_EARLY_INIT_F	1
-
-/***************************************************************
- * U-boot generic defines start here.
- ***************************************************************/
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Command line configuration */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-
-#define CONFIG_PCI
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_PCI_PNP
-#define CONFIG_IXP_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_CMD_PCI_ENUM
-#endif
-
-#define CONFIG_BOOTCOMMAND		"run boot_flash"
-/* enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG		1
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_KGDB_BAUDRATE		230400
-#endif
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE			256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS			16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE			CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START		0x00400000
-#define CONFIG_SYS_MEMTEST_END			0x00800000
-
-/* timer clock - 2* OSC_IN system clock */
-#define CONFIG_IXP425_TIMER_CLK                 66000000
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR			0x00010000
-
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, \
-					  115200, 230400 }
-#define CONFIG_SERIAL_RTS_ACTIVE	1
-
-/* Expansion bus settings */
-#define CONFIG_SYS_EXP_CS0			0xbd113003
-
-/* SDRAM settings */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_SDRAM_BASE			0x00000000
-
-/* 32MB SDRAM */
-#define CONFIG_SYS_SDR_CONFIG			0x18
-#define PHYS_SDRAM_1_SIZE		0x02000000
-#define CONFIG_SYS_SDRAM_REFRESH_CNT		0x81a
-#define CONFIG_SYS_SDR_MODE_CONFIG		0x1
-#define CONFIG_SYS_DRAM_SIZE			0x02000000
-
-/* FLASH organization */
-#define CONFIG_SYS_TEXT_BASE		0x50000000
-#define CONFIG_SYS_MAX_FLASH_BANKS		2
-/* max # of sectors per chip */
-#define CONFIG_SYS_MAX_FLASH_SECT		70
-#define PHYS_FLASH_1			0x50000000
-#define PHYS_FLASH_2			0x51000000
-#define CONFIG_SYS_FLASH_BANKS_LIST		{ PHYS_FLASH_1, PHYS_FLASH_2 }
-
-#define CONFIG_SYS_FLASH_BASE			PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN			(252 << 10)
-#define CONFIG_BOARD_SIZE_LIMIT			258048
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* board provides its own flash_init code */
-#define CONFIG_FLASH_CFI_LEGACY		1
-/* no byte writes on IXP4xx */
-#define CONFIG_SYS_FLASH_CFI_WIDTH		FLASH_CFI_16BIT
-/* SST 39VF020 etc. support */
-#define CONFIG_SYS_FLASH_LEGACY_256Kx8	1
-
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* Ethernet */
-
-/* include IXP4xx NPE support */
-#define CONFIG_IXP4XX_NPE		1
-
-/* NPE0 PHY address */
-#define	CONFIG_PHY_ADDR			0x1C
-/* MII PHY management */
-#define CONFIG_MII			1
-
-/* Number of ethernet rx buffers & descriptors */
-#define CONFIG_SYS_RX_ETH_BUFFER		16
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#undef  CONFIG_CMD_NFS
-
-/* BOOTP options */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE		32
-
-/* environment organization: one complete 4k flash sector */
-#define	CONFIG_ENV_IS_IN_FLASH		1
-#define CONFIG_ENV_SIZE			0x1000
-#define CONFIG_ENV_ADDR			(PHYS_FLASH_1 + 0x3f000)
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"npe_ucode=51000000\0"						\
-	"mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);"			\
-	"IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0"		\
-	"kerneladdr=51020000\0"						\
-	"kernelfile=actux4/uImage\0"					\
-	"rootfile=actux4/rootfs\0"					\
-	"rootaddr=51160000\0"						\
-	"loadaddr=10000\0"						\
-	"updateboot_ser=mw.b 10000 ff 40000;"				\
-	" loady ${loadaddr};"						\
-	" run eraseboot writeboot\0"					\
-	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} actux4/u-boot.bin;"					\
-	" run eraseboot writeboot\0"					\
-	"eraseboot=protect off 50000000 5003efff;"			\
-	" erase 50000000 +${filesize}\0"				\
-	"writeboot=cp.b 10000 50000000 ${filesize}\0"			\
-	"updateucode=loady;"						\
-	" era ${npe_ucode} +${filesize};"				\
-	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
-	"updateroot=tftp ${loadaddr} ${rootfile};"			\
-	" era ${rootaddr} +${filesize};"				\
-	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\
-	"updatekern=tftp ${loadaddr} ${kernelfile};"			\
-	" era ${kerneladdr} +${filesize};"				\
-	" cp.b ${loadaddr} ${kerneladdr} ${filesize}\0"			\
-	"flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
-	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"	\
-	"boot_flash=run flashargs addtty addeth;"			\
-	" bootm ${kerneladdr}\0"					\
-	"boot_net=run netargs addtty addeth;"				\
-	" tftpboot ${loadaddr} ${kernelfile};"				\
-	" bootm\0"
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_INIT_SP_ADDR						\
-	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/dvlhost.h b/include/configs/dvlhost.h
deleted file mode 100644
index 1af7f16..0000000
--- a/include/configs/dvlhost.h
+++ /dev/null
@@ -1,222 +0,0 @@
-/*
- * (C) Copyright 2009
- * Michael Schwingen, michael@schwingen.org
- *
- * Configuration settings for the
- * dLAN200 AV Wireless G ("dvlhost") board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_IXP425			1
-#define CONFIG_DVLHOST			1
-
-#define	CONFIG_MACH_TYPE		1343
-
-#define CONFIG_DISPLAY_CPUINFO		1
-#define CONFIG_DISPLAY_BOARDINFO	1
-
-#define CONFIG_IXP_SERIAL
-#define CONFIG_SYS_IXP425_CONSOLE	IXP425_UART2
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_BOOTDELAY		3
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_BOARD_EARLY_INIT_F	1
-#define CONFIG_SYS_LDSCRIPT	"board/dvlhost/u-boot.lds"
-
-/***************************************************************
- * U-boot generic defines start here.
- ***************************************************************/
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN			(CONFIG_ENV_SIZE + 128*1024)
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Command line configuration. */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_PCI
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_PCI_PNP
-#define CONFIG_IXP_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_CMD_PCI_ENUM
-#endif
-
-#define CONFIG_BOOTCOMMAND		"run boot_flash"
-/* enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG		1
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_KGDB_BAUDRATE		230400
-#endif
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE		256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS		16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START	0x00000000
-#define CONFIG_SYS_MEMTEST_END		0x01D80000
-
-/* timer clock - 2* OSC_IN system clock */
-#define CONFIG_IXP425_TIMER_CLK         66666666
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR		0x00010000
-
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
-					  115200, 230400 }
-#define CONFIG_SERIAL_RTS_ACTIVE	1
-
-/* Expansion bus settings */
-#define CONFIG_SYS_EXP_CS0		0xbd113442
-
-/* SDRAM settings */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x00000000
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-
-/* 32MB SDRAM: 2* 8Mx16, CL3 */
-#define CONFIG_SYS_SDR_CONFIG		0x18
-#define PHYS_SDRAM_1_SIZE		0x02000000
-#define CONFIG_SYS_SDRAM_REFRESH_CNT	0x800
-#define CONFIG_SYS_SDR_MODE_CONFIG	0x1
-#define CONFIG_SYS_DRAM_SIZE		PHYS_SDRAM_1_SIZE
-
-/* FLASH organization: one Spansion S29AL032D-04 Flash */
-#define CONFIG_SYS_TEXT_BASE		0x50000000
-#define CONFIG_SYS_MAX_FLASH_BANKS	1
-/* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_SECT	140
-#define PHYS_FLASH_1			0x50000000
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ PHYS_FLASH_1 }
-
-#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)
-#define CONFIG_BOARD_SIZE_LIMIT         262144
-
-/* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-/* no byte writes on IXP4xx */
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
-
-/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* Ethernet */
-
-/* include IXP4xx NPE support */
-#define CONFIG_IXP4XX_NPE		1
-
-/* NPE0 PHY: MII dLAN200 AVmodule, 100BaseT-FDX fixed */
-#define	CONFIG_PHY_ADDR			0x18
-/* NPE1 PHY: MII IP175 switch, port 5 is host port */
-#define	CONFIG_PHY1_ADDR		0x05
-/* MII PHY management */
-#define CONFIG_MII			1
-/* fixed-speed powerline modem without standard PHY registers on MII */
-#define CONFIG_MII_NPE0_FIXEDLINK       1
-#define CONFIG_MII_NPE0_SPEED           100
-#define CONFIG_MII_NPE0_FULLDUPLEX      1
-/* fixed-speed switch without standard PHY registers on MII */
-#define CONFIG_MII_NPE1_FIXEDLINK       1
-#define CONFIG_MII_NPE1_SPEED           100
-#define CONFIG_MII_NPE1_FULLDUPLEX      1
-
-/* Number of ethernet rx buffers & descriptors */
-#define CONFIG_SYS_RX_ETH_BUFFER	16
-#define CONFIG_RESET_PHY_R		1
-/* ethernet switch connected to MII port */
-#define CONFIG_MII_ETHSWITCH		1
-#define CONFIG_HAS_ETH1			1
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#undef  CONFIG_CMD_NFS
-
-/* BOOTP options */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE	32
-
-/*
- * environment organization:
- * one flash sector, embedded in uboot area (bottom bootblock flash)
- */
-#define	CONFIG_ENV_IS_IN_FLASH		1
-#define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_ADDR			(PHYS_FLASH_1 + 0x4000)
-#define CONFIG_SYS_USE_PPCENV		1
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"npe_ucode=50040000\0"						\
-	"ethprime=NPE1\0"						\
-	"ethrotate=no\0"						\
-	"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root),\0" \
-	"kerneladdr=50050000\0"						\
-	"kernelfile=dvlhost/uImage\0"					\
-	"rootfile=dvlhost/rootfs\0"					\
-	"rootaddr=50170000\0"						\
-	"loadaddr=10000\0"						\
-	"updateboot_ser=mw.b 10000 ff 40000;"				\
-	" loady ${loadaddr};"						\
-	" run eraseboot writeboot\0"					\
-	"updateboot_net=mw.b 10000 ff 40000;"				\
-	" tftp ${loadaddr} dvlhost/u-boot.bin;"				\
-	" run eraseboot writeboot\0"					\
-	"eraseboot=protect off 50000000 50003fff;"			\
-	" protect off 50006000 5003ffff;"				\
-	" erase 50000000 50003fff;"					\
-	" erase 50006000 5003ffff\0"					\
-	"writeboot=cp.b 10000 50000000 4000;"				\
-	" cp.b 16000 50006000 3a000\0"					\
-	"updateucode=loady;"						\
-	" era ${npe_ucode} +${filesize};"				\
-	" cp.b ${loadaddr} ${npe_ucode} ${filesize}\0"			\
-	"updateroot=tftp ${loadaddr} ${rootfile};"			\
-	" era ${rootaddr} +${filesize};"				\
-	" cp.b ${loadaddr} ${rootaddr} ${filesize}\0"			\
-	"updatekern=tftp ${loadaddr} ${kernelfile};"			\
-	" era ${kerneladdr} +${filesize};"				\
-	" cp.b ${loadaddr} ${kerneladdr} ${filesize}\0"			\
-	"flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3"	\
-	" rootfstype=squashfs,jffs2 init=/etc/preinit\0"		\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
-	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"	\
-	"boot_flash=run flashargs addtty addeth;"			\
-	" bootm ${kerneladdr}\0"					\
-	"boot_net=run netargs addtty addeth;"				\
-	" tftpboot ${loadaddr} ${kernelfile};"				\
-	" bootm\0"
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_INIT_SP_ADDR						\
-	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */