mpc8260: remove MPC8266ADS board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rune Torgersen <runet@innovsys.com>

1 files changed, 0 insertions, 563 deletions

diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h
deleted file mode 100644
index 8d9c8fb..0000000
--- a/include/configs/MPC8266ADS.h
+++ /dev/null
@@ -1,563 +0,0 @@
-/*
- * (C) Copyright 2001
- * Stuart Hughes <stuarth@lineo.com>
- * This file is based on similar values for other boards found in other
- * U-Boot config files, and some that I found in the mpc8260ads manual.
- *
- * Note: my board is a PILOT rev.
- * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Config header file for a MPC8266ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
- */
-
-/* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
-   !!								      !!
-   !!  This configuration requires JP3 to be in position 1-2 to work  !!
-   !!  To make it work for the default, the CONFIG_SYS_TEXT_BASE define in	      !!
-   !!  board/mpc8266ads/config.mk must be changed from 0xfe000000 to  !!
-   !!  0xfff00000						      !!
-   !!  The CONFIG_SYS_HRCW_MASTER define below must also be changed to match !!
-   !!								      !!
-   !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8266ADS	1	/* ...on motorola ADS board	*/
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define	CONFIG_SYS_TEXT_BASE	0xfe000000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
-#define CONFIG_RESET_PHY_R	1	/* Call reset_phy()		*/
-
-/* allow serial and ethaddr to be overwritten */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#undef	CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#define CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef	CONFIG_CONS_NONE		/* define if console on something else */
-#define CONFIG_CONS_INDEX	1	/* which serial channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC   */
-#define CONFIG_ETHER_ON_FCC		/* define if ether on FCC   */
-#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_INDEX	2	/* which channel for ether  */
-#define CONFIG_MII			/* MII PHY management		*/
-#define CONFIG_BITBANGMII		/* bit-bang MII PHY management	*/
-/*
- * Port pins used for bit-banged MII communictions (if applicable).
- */
-#define MDIO_PORT	2	/* Port C */
-#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ( \
-				(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE	MDIO_DECLARE
-
-#define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
-#define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
-#define MDIO_READ	((iop->pdat &  0x00400000) != 0)
-
-#define MDIO(bit)	if(bit) iop->pdat |=  0x00400000; \
-			else	iop->pdat &= ~0x00400000
-
-#define MDC(bit)	if(bit) iop->pdat |=  0x00200000; \
-			else	iop->pdat &= ~0x00200000
-
-#define MIIDELAY	udelay(1)
-
-#if (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Half duplex
- */
-# define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	0
-# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif	/* CONFIG_ETHER_INDEX */
-
-/* other options */
-#define CONFIG_HARD_I2C		1	/* To enable I2C support	*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* PCI */
-#define CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_PNP
-#define CONFIG_PCI_BOOTDELAY 0
-#undef CONFIG_PCI_SCAN_SHOW
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS	0x50
-
-#define CONFIG_8260_CLKIN	66000000	/* in Hz */
-#define CONFIG_BAUDRATE		115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-/* Commands we want, that are not part of default set */
-#define CONFIG_CMD_ASKENV	/* ask for env variable		*/
-#define CONFIG_CMD_CACHE	/* icache, dcache		*/
-#define CONFIG_CMD_DHCP		/* DHCP Support			*/
-#define CONFIG_CMD_DIAG		/* Diagnostics			*/
-#define CONFIG_CMD_IMMAP	/* IMMR dump support		*/
-#define CONFIG_CMD_IRQ		/* irqinfo			*/
-#define CONFIG_CMD_MII		/* MII support			*/
-#define CONFIG_CMD_PCI		/* pciinfo			*/
-#define CONFIG_CMD_PING		/* ping support			*/
-#define CONFIG_CMD_PORTIO	/* Port I/O			*/
-#define CONFIG_CMD_REGINFO	/* Register dump		*/
-#define CONFIG_CMD_SAVES	/* save S record dump		*/
-#define CONFIG_CMD_SDRAM	/* SDRAM DIMM SPD info printout */
-
-/* Commands from default set we don't need */
-#undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
-#undef CONFIG_CMD_SETGETDCR	/* DCR support on 4xx		*/
-
-/* Define a command string that is automatically executed when no character
- * is read on the console interface withing "Boot Delay" after reset.
- */
-#undef	CONFIG_BOOT_ROOT_INITRD		/* Use ram disk for the root file system */
-#define CONFIG_BOOT_ROOT_NFS		/* Use a NFS mounted root file system */
-
-#ifdef CONFIG_BOOT_ROOT_INITRD
-#define CONFIG_BOOTCOMMAND \
-	"version;" \
-	"echo;" \
-	"bootp;" \
-	"setenv bootargs root=/dev/ram0 rw " \
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
-	"bootm"
-#endif /* CONFIG_BOOT_ROOT_INITRD */
-
-#ifdef CONFIG_BOOT_ROOT_NFS
-#define CONFIG_BOOTCOMMAND \
-	"version;" \
-	"echo;" \
-	"bootp;" \
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
-	"bootm"
-#endif /* CONFIG_BOOT_ROOT_NFS */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-
-#if defined(CONFIG_CMD_KGDB)
-#undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
-#undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX	2	/* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
-#endif
-
-#undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE	256			/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16			/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
-
-#undef CONFIG_CLOCKS_IN_MHZ		/* clocks passsed to Linux in MHz */
-					/* for versions < 2.4.5-pre5	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_SYS_FLASH_BASE		0xFE000000
-#define FLASH_BASE		0xFE000000
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	32	/* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_SIZE		8
-#define CONFIG_SYS_FLASH_ERASE_TOUT	8000	/* Timeout for Flash Erase (in ms)    */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	5	/* Timeout for Flash Write (in ms)    */
-
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-
-/* this is stuff came out of the Motorola docs */
-/* Only change this if you also change the Hardware configuration Word */
-#define CONFIG_SYS_DEFAULT_IMMR	0x0F010000
-
-/* Set IMMR to 0xF0000000 or above to boot Linux  */
-#define CONFIG_SYS_IMMR		0xF0000000
-#define CONFIG_SYS_BCSR		0xF8000000
-#define CONFIG_SYS_PCI_INT		0xF8200000	/* PCI interrupt controller */
-
-/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes
- */
-/*#define CONFIG_VERY_BIG_RAM	1*/
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)?  This will normally auto-configure via the SPD.
-*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_SIZE 16
-
-#define SDRAM_SPD_ADDR 0x50
-
-/*-----------------------------------------------------------------------
- * BR2,BR3 - Base Register
- *     Ref: Section 10.3.1 on page 10-14
- * OR2,OR3 - Option Register
- *     Ref: Section 10.3.2 on page 10-16
- *-----------------------------------------------------------------------
- */
-
-/* Bank 2,3 - SDRAM DIMM
- */
-
-/* The BR2 is configured as follows:
- *
- *     - Base address of 0x00000000
- *     - 64 bit port size (60x bus only)
- *     - Data errors checking is disabled
- *     - Read and write access
- *     - SDRAM 60x bus
- *     - Access are handled by the memory controller according to MSEL
- *     - Not used for atomic operations
- *     - No data pipelining is done
- *     - Valid
- */
-#define CONFIG_SYS_BR2_PRELIM	((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
-			 BRx_PS_64			|\
-			 BRx_MS_SDRAM_P			|\
-			 BRx_V)
-
-#define CONFIG_SYS_BR3_PRELIM	((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
-			 BRx_PS_64			|\
-			 BRx_MS_SDRAM_P			|\
-			 BRx_V)
-
-/* With a 64 MB DIMM, the OR2 is configured as follows:
- *
- *     - 64 MB
- *     - 4 internal banks per device
- *     - Row start address bit is A8 with PSDMR[PBI] = 0
- *     - 12 row address lines
- *     - Back-to-back page mode
- *     - Internal bank interleaving within save device enabled
- */
-#if (CONFIG_SYS_SDRAM_SIZE == 64)
-#define CONFIG_SYS_OR2_PRELIM	(MEG_TO_AM(CONFIG_SYS_SDRAM_SIZE)	|\
-			 ORxS_BPD_4			|\
-			 ORxS_ROWST_PBI0_A8		|\
-			 ORxS_NUMR_12)
-#elif (CONFIG_SYS_SDRAM_SIZE == 16)
-#define CONFIG_SYS_OR2_PRELIM	(0xFF000C80)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-/*-----------------------------------------------------------------------
- * PSDMR - 60x Bus SDRAM Mode Register
- *     Ref: Section 10.3.3 on page 10-21
- *-----------------------------------------------------------------------
- */
-
-#if (CONFIG_SYS_SDRAM_SIZE == 64)
-/* With a 64 MB DIMM, the PSDMR is configured as follows:
- *
- *     - Bank Based Interleaving,
- *     - Refresh Enable,
- *     - Address Multiplexing where A5 is output on A14 pin
- *	 (A6 on A15, and so on),
- *     - use address pins A14-A16 as bank select,
- *     - A9 is output on SDA10 during an ACTIVATE command,
- *     - earliest timing for ACTIVATE command after REFRESH command is 7 clocks,
- *     - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command
- *	 is 3 clocks,
- *     - earliest timing for READ/WRITE command after ACTIVATE command is
- *	 2 clocks,
- *     - earliest timing for PRECHARGE after last data was read is 1 clock,
- *     - earliest timing for PRECHARGE after last data was written is 1 clock,
- *     - CAS Latency is 2.
- */
-#define CONFIG_SYS_PSDMR	(PSDMR_RFEN	      |\
-			 PSDMR_SDAM_A14_IS_A5 |\
-			 PSDMR_BSMA_A14_A16   |\
-			 PSDMR_SDA10_PBI0_A9  |\
-			 PSDMR_RFRC_7_CLK     |\
-			 PSDMR_PRETOACT_3W    |\
-			 PSDMR_ACTTORW_2W     |\
-			 PSDMR_LDOTOPRE_1C    |\
-			 PSDMR_WRC_1C	      |\
-			 PSDMR_CL_2)
-#elif (CONFIG_SYS_SDRAM_SIZE == 16)
-/* With a 16 MB DIMM, the PSDMR is configured as follows:
- *
- *   configuration parameters found in Motorola documentation
- */
-#define CONFIG_SYS_PSDMR	(0x016EB452)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-#define RS232EN_1		0x02000002
-#define RS232EN_2		0x01000001
-#define FETHIEN			0x08000008
-#define FETH_RST		0x04000004
-
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Use this HRCW for booting from address 0xfe00000 (JP3 in setting 1-2)  */
-/* 0x0EB2B645 */
-#define CONFIG_SYS_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP )				|\
-			 ( HRCW_L2CPC10 | HRCW_DPPC11 | HRCW_ISB010 )		|\
-			 ( HRCW_BMS | HRCW_MMR11 | HRCW_LBPC01 | HRCW_APPC10 )	|\
-			 ( HRCW_CS10PC01 | HRCW_MODCK_H0101 )			\
-			)
-
-/* Use this HRCW for booting from address 0xfff0000 (JP3 in setting 2-3)  */
-/* #define CONFIG_SYS_HRCW_MASTER 0x0cb23645 */
-
-/* This value should actually be situated in the first 256 bytes of the FLASH
-	which on the standard MPC8266ADS board is at address 0xFF800000
-	The linker script places it at 0xFFF00000 instead.
-
-	It still works, however, as long as the ADS board jumper JP3 is set to
-	position 2-3 so the board is using the BCSR as Hardware Configuration Word
-
-	If you want to use the one defined here instead, ust copy the first 256 bytes from
-	0xfff00000 to 0xff800000  (for 8MB flash)
-
-	- Rune
-
-*/
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#  define CONFIG_ENV_IS_IN_FLASH	1
-#    define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE + 0x40000)
-#    define CONFIG_ENV_SECT_SIZE	0x40000
-#else
-#  define CONFIG_ENV_IS_IN_NVRAM	1
-#  define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#  define CONFIG_ENV_SIZE		0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPU */
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers			 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-/*#define CONFIG_SYS_HID0_INIT		0 */
-#define CONFIG_SYS_HID0_INIT	(HID0_ICE  |\
-			 HID0_DCE  |\
-			 HID0_ICFI |\
-			 HID0_DCI  |\
-			 HID0_IFEM |\
-			 HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL		(HID0_ICE | HID0_IFEM | HID0_ABE )
-
-#define CONFIG_SYS_HID2		0
-
-#define CONFIG_SYS_SYPCR		0xFFFFFFC3
-#define CONFIG_SYS_BCR			0x004C0000
-#define CONFIG_SYS_SIUMCR		0x4E64C000
-#define CONFIG_SYS_SCCR		0x00000000
-
-/*	local bus memory map
- *
- *	0x00000000-0x03FFFFFF	 64MB	SDRAM
- *	0x80000000-0x9FFFFFFF	512MB	outbound prefetchable PCI memory window
- *	0xA0000000-0xBFFFFFFF	512MB	outbound non-prefetchable PCI memory window
- *	0xF0000000-0xF001FFFF	128KB	MPC8266 internal memory
- *	0xF4000000-0xF7FFFFFF	 64MB	outbound PCI I/O window
- *	0xF8000000-0xF8007FFF	 32KB	BCSR
- *	0xF8100000-0xF8107FFF	 32KB	ATM UNI
- *	0xF8200000-0xF8207FFF	 32KB	PCI interrupt controller
- *	0xF8300000-0xF8307FFF	 32KB	EEPROM
- *	0xFE000000-0xFFFFFFFF	 32MB	flash
- */
-#define CONFIG_SYS_BR0_PRELIM	0xFE001801		/* flash */
-#define CONFIG_SYS_OR0_PRELIM	0xFE000836
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_BCSR | 0x1801)	/* BCSR */
-#define CONFIG_SYS_OR1_PRELIM	0xFFFF8010
-#define CONFIG_SYS_BR4_PRELIM	0xF8300801		/* EEPROM */
-#define CONFIG_SYS_OR4_PRELIM	0xFFFF8846
-#define CONFIG_SYS_BR5_PRELIM	0xF8100801		/* PM5350 ATM UNI */
-#define CONFIG_SYS_OR5_PRELIM	0xFFFF8E36
-#define CONFIG_SYS_BR8_PRELIM	(CONFIG_SYS_PCI_INT | 0x1801)	/* PCI interrupt controller */
-#define CONFIG_SYS_OR8_PRELIM	0xFFFF8010
-
-#define CONFIG_SYS_RMR			0x0001
-#define CONFIG_SYS_TMCNTSC		(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-#define CONFIG_SYS_PISCR		(PISCR_PS|PISCR_PTF|PISCR_PTE)
-#define CONFIG_SYS_RCCR		0
-#define CONFIG_SYS_MPTPR		0x00001900
-#define CONFIG_SYS_PSRT		0x00000021
-
-/* This address must not exist */
-#define CONFIG_SYS_RESET_ADDRESS	0xFCFFFF00
-
-/* PCI Memory map (if different from default map */
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE		/* Local base */
-#define CONFIG_SYS_PCI_SLV_MEM_BUS		0x00000000		/* PCI base */
-#define CONFIG_SYS_PICMR0_MASK_ATTRIB	(PICMR_MASK_512MB | PICMR_ENABLE | \
-				 PICMR_PREFETCH_EN)
-
-/*
- * These are the windows that allow the CPU to access PCI address space.
- * All three PCI master windows, which allow the CPU to access PCI
- * prefetch, non prefetch, and IO space (see below), must all fit within
- * these windows.
- */
-
-/* PCIBR0 */
-#define CONFIG_SYS_PCI_MSTR0_LOCAL		0x80000000		/* Local base */
-#define CONFIG_SYS_PCIMSK0_MASK		PCIMSK_1GB		/* Size of window */
-/* PCIBR1 */
-#define CONFIG_SYS_PCI_MSTR1_LOCAL		0xF4000000		/* Local base */
-#define CONFIG_SYS_PCIMSK1_MASK		PCIMSK_64MB		/* Size of window */
-
-/*
- * Master window that allows the CPU to access PCI Memory (prefetch).
- * This window will be setup with the first set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL	0x80000000			/* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEM_BUS	0x80000000			/* PCI base   */
-#define CONFIG_SYS_CPU_PCI_MEM_START	PCI_MSTR_MEM_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEM_SIZE	0x20000000			/* 512MB */
-#define CONFIG_SYS_POCMR0_MASK_ATTRIB	(POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)
-
-/*
- * Master window that allows the CPU to access PCI Memory (non-prefetch).
- * This window will be setup with the second set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL    0xA0000000			/* Local base */
-#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS	    0xA0000000			/* PCI base   */
-#define CONFIG_SYS_CPU_PCI_MEMIO_START	    PCI_MSTR_MEMIO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE	    0x20000000			/* 512MB */
-#define CONFIG_SYS_POCMR1_MASK_ATTRIB	    (POCMR_MASK_512MB | POCMR_ENABLE)
-
-/*
- * Master window that allows the CPU to access PCI IO space.
- * This window will be setup with the third set of Outbound ATU registers
- * in the bridge.
- */
-
-#define CONFIG_SYS_PCI_MSTR_IO_LOCAL	    0xF4000000			/* Local base */
-#define CONFIG_SYS_PCI_MSTR_IO_BUS	    0xF4000000			/* PCI base   */
-#define CONFIG_SYS_CPU_PCI_IO_START	    PCI_MSTR_IO_LOCAL
-#define CONFIG_SYS_PCI_MSTR_IO_SIZE	    0x04000000			/* 64MB */
-#define CONFIG_SYS_POCMR2_MASK_ATTRIB	    (POCMR_MASK_64MB | POCMR_ENABLE | POCMR_PCI_IO)
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		""
-#define MTDPARTS_DEFAULT	""
-*/
-
-#endif /* __CONFIG_H */