Merge with git://www.denx.de/git/u-boot.git

100 files changed, 6291 insertions, 840 deletions

diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index 9e0ee37..9adbba9 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -53,9 +53,13 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_NET_MULTI	1
+#undef  CONFIG_HAS_ETH1
+
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -144,40 +148,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h
index 62a2eaa..0321650 100644
--- a/include/configs/CATcenter.h
+++ b/include/configs/CATcenter.h
@@ -399,6 +399,8 @@
 #define CFG_ENV_ADDR_REDUND	0xFFFFA000
 #define CFG_ENV_SIZE_REDUND	0x2000
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 #define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
 #define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
 
diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h
index 08ef9b5..21cd9c1 100644
--- a/include/configs/CMS700.h
+++ b/include/configs/CMS700.h
@@ -90,8 +90,6 @@
 #define CONFIG_CMD_EEPROM
 
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
@@ -157,36 +155,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h
index 0a4e1e9..1b948f6 100644
--- a/include/configs/CPCI405.h
+++ b/include/configs/CPCI405.h
@@ -92,8 +92,6 @@
 
 #define CONFIG_SUPPORT_VFAT
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index ceeba6e..fb71c5f 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -114,8 +114,6 @@
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
 #endif
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 1aefbba..4994319 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -100,9 +100,6 @@
 
 #define CONFIG_SUPPORT_VFAT
 
-#define CFG_NAND_LEGACY
-
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h
index e2652e6..29f9292 100644
--- a/include/configs/CPCI405DT.h
+++ b/include/configs/CPCI405DT.h
@@ -111,8 +111,6 @@
 
 #undef  CONFIG_AUTO_UPDATE              /* autoupdate via compactflash  */
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/EB+MCF-EV123.h b/include/configs/EB+MCF-EV123.h
index a8697ec..dae5295 100644
--- a/include/configs/EB+MCF-EV123.h
+++ b/include/configs/EB+MCF-EV123.h
@@ -40,9 +40,8 @@
 
 #define CONFIG_MISC_INIT_R
 
-#define FEC_ENET
-#define CONFIG_ETHADDR 00:CF:52:82:EB:01
-
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE 9600
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
@@ -84,7 +83,39 @@
 #include <config_cmd_default.h>
 
 #undef CONFIG_CMD_LOADB
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:CF:52:82:EB:01
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
 
 #define CONFIG_BOOTDELAY	5
 #define CFG_PROMPT		"\nEV123 U-Boot> "
@@ -122,9 +153,6 @@
  */
 #define	CFG_MBAR		0x40000000
 
-#define	CFG_DISCOVER_PHY
-/* #define	CFG_ENET_BD_BASE	0x380000 */
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
@@ -151,6 +179,7 @@
 
 #define CFG_FLASH_BASE		0xFFE00000
 #define	CFG_INT_FLASH_BASE	0xF0000000
+#define CFG_INT_FLASH_ENABLE	0x21
 
 /* If M5282 port is fully implemented the monitor base will be behind
  * the vector table. */
diff --git a/include/configs/FADS823.h b/include/configs/FADS823.h
index a562b2f..f810af2 100644
--- a/include/configs/FADS823.h
+++ b/include/configs/FADS823.h
@@ -206,6 +206,7 @@
 #define	CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_OFFSET		0x00040000	/* Offset of Environment Sector */
 #define	CFG_ENV_SIZE		0x40000	/* Total Size of Environment Sector	*/
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
diff --git a/include/configs/FADS850SAR.h b/include/configs/FADS850SAR.h
index c8ce259..a09c0e0 100644
--- a/include/configs/FADS850SAR.h
+++ b/include/configs/FADS850SAR.h
@@ -156,6 +156,7 @@
 #define	CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_OFFSET		0x00040000	/* Offset of Environment Sector */
 #define	CFG_ENV_SIZE		0x40000	/* Total Size of Environment Sector	*/
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
diff --git a/include/configs/FPS850L.h b/include/configs/FPS850L.h
index 322158c..3b0ddb4 100644
--- a/include/configs/FPS850L.h
+++ b/include/configs/FPS850L.h
@@ -39,28 +39,44 @@
 #undef	CONFIG_8xx_CONS_SMC1
 #define	CONFIG_8xx_CONS_SMC2	1	/* Console is on SMC2		*/
 #undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		19200
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-#define CONFIG_BOOTCOMMAND	"bootm 40020000" /* autoboot command	*/
+#define CONFIG_BAUDRATE		115200
 
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define	CONFIG_BOOTCOUNT_LIMIT
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
 #define CONFIG_BOARD_TYPES	1	/* support board types		*/
 
-#define CONFIG_BOOTARGS		"root=/dev/nfs rw "			\
-				"nfsroot=10.0.0.2:/opt/eldk/ppc_8xx "	\
-				"nfsaddrs=10.0.0.99:10.0.0.2"
+#define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"flash_nfs=run nfsargs addip;"					\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip;"					\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
+	"rootpath=/opt/eldk/ppc_8xx\0"					\
+	"bootfile=/tftpboot/fps850L/uImage\0"				\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-
 /*
  * BOOTP options
  */
@@ -80,24 +96,32 @@
 #define CONFIG_BOOTP_NTPSERVER
 #define CONFIG_BOOTP_TIMEOFFSET
 
+#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
 
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 
-#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_CACHE
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
 
 
 /*
  * Miscellaneous configurable options
  */
 #define	CFG_LONGHELP			/* undef to save memory		*/
-#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CFG_HUSH_PARSER		1	/* Use the HUSH parser		*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
 #if defined(CONFIG_CMD_KGDB)
 #define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
diff --git a/include/configs/FPS860L.h b/include/configs/FPS860L.h
index f8698b5..6fec075 100644
--- a/include/configs/FPS860L.h
+++ b/include/configs/FPS860L.h
@@ -40,18 +40,37 @@
 #define	CONFIG_8xx_CONS_SMC2	1	/* Console is on SMC2		*/
 #undef	CONFIG_8xx_CONS_NONE
 #define CONFIG_BAUDRATE		115200
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
+
+#define	CONFIG_BOOTCOUNT_LIMIT
+
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-#define CONFIG_BOOTCOMMAND	"bootm 40040000" /* autoboot command	*/
 
 #define CONFIG_BOARD_TYPES	1	/* support board types		*/
 
-#define CONFIG_BOOTARGS		"root=/dev/nfs rw "			\
-				"nfsroot=10.0.0.2:/opt/eldk/ppc_8xx "	\
-				"nfsaddrs=10.0.0.99:10.0.0.2"
+#define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"flash_nfs=run nfsargs addip;"					\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip;"					\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
+	"rootpath=/opt/eldk/ppc_8xx\0"					\
+	"bootfile=/tftpboot/fps850L/uImage\0"				\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
@@ -79,11 +98,11 @@
 
 #define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
 
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
+
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
@@ -95,7 +114,14 @@
  * Miscellaneous configurable options
  */
 #define	CFG_LONGHELP			/* undef to save memory		*/
-#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CFG_HUSH_PARSER		1	/* Use the HUSH parser		*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
 #if defined(CONFIG_CMD_KGDB)
 #define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
diff --git a/include/configs/HH405.h b/include/configs/HH405.h
index 00f481c..8967b3f 100644
--- a/include/configs/HH405.h
+++ b/include/configs/HH405.h
@@ -141,8 +141,6 @@
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
 #undef CONFIG_AUTO_UPDATE_SHOW          /* use board show routine       */
 
-#define CFG_NAND_LEGACY
-
 #undef  CONFIG_BZIP2	 /* include support for bzip2 compressed images */
 #undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -209,36 +207,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index 661b895..1ff7108 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -147,38 +147,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
diff --git a/include/configs/ICU862.h b/include/configs/ICU862.h
index 27a5bc3..da54cef 100644
--- a/include/configs/ICU862.h
+++ b/include/configs/ICU862.h
@@ -234,6 +234,7 @@
 
 #define CFG_ENV_SECT_SIZE	0x40000	/* Total Size of Environment sector	*/
 #define	CFG_ENV_SIZE		0x4000	/* Used Size of Environment Sector	*/
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h
index 1a7167b..4c16d22 100644
--- a/include/configs/IceCube.h
+++ b/include/configs/IceCube.h
@@ -85,7 +85,6 @@
 
 /* USB */
 #define CONFIG_USB_OHCI_NEW
-#define ADD_USB_CMD             CFG_CMD_USB | CFG_CMD_FAT
 #define CONFIG_USB_STORAGE
 #define CFG_OHCI_BE_CONTROLLER
 #undef CFG_USB_OHCI_BOARD_INIT
@@ -179,12 +178,9 @@
 #endif /* CONFIG_MPC5200 */
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h
new file mode 100644
index 0000000..7f544c8
--- /dev/null
+++ b/include/configs/M5235EVB.h
@@ -0,0 +1,261 @@
+/*
+ * Configuation settings for the Freescale MCF5329 FireEngine board.
+ *
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5235EVB_H
+#define _M5235EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF523x		/* define processor family */
+#define CONFIG_M5235		/* define processor type */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT	5000	/* timeout in milliseconds, max timeout is 6.71sec */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+/* Timer */
+#define CONFIG_MCFTMR
+#undef CONFIG_MCFPIT
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C			/* I2C with hw support */
+#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		80000
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x00000300
+#define CFG_IMMR		CFG_MBAR
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#define CONFIG_BOOTFILE		"u-boot.bin"
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* FEC_ENET */
+
+#define CONFIG_HOSTNAME		M5235EVB
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
+
+#define CONFIG_PRAM		512	/* 512 KB */
+#define CFG_PROMPT		"-> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#if defined(CONFIG_KGDB)
+#	define CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#else
+#	define CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
+#define CFG_LOAD_ADDR		(CFG_SDRAM_BASE+0x20000)
+
+#define CFG_HZ			1000
+#define CFG_CLK			75000000
+#define CFG_CPU_CLK		CFG_CLK * 2
+
+#define CFG_MBAR		0x40000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL	0x21
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE - 0x10)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
+
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END		((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+
+#define CFG_BOOTPARAMS_LEN	64*1024
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x800000	/* Max size that the board might have */
+#ifdef NORFLASH_PS32BIT
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_32BIT
+#else
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#endif
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#endif
+
+#define CFG_FLASH_BASE		(CFG_CS0_BASE << 16)
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_IS_EMBEDDED	1
+#ifdef NORFLASH_PS32BIT
+#	define CFG_ENV_OFFSET		(0x8000)
+#	define CFG_ENV_SIZE		0x4000
+#	define CFG_ENV_SECT_SIZE	0x4000
+#else
+#	define CFG_ENV_OFFSET		(0x4000)
+#	define CFG_ENV_SIZE		0x2000
+#	define CFG_ENV_SECT_SIZE	0x2000
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16
+
+/*-----------------------------------------------------------------------
+ * Chipselect bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - Available
+ * CS2 - Available
+ * CS3 - Available
+ * CS4 - Available
+ * CS5 - Available
+ * CS6 - Available
+ * CS7 - Available
+ */
+#ifdef NORFLASH_PS32BIT
+#	define CFG_CS0_BASE	0xFFC0
+#	define CFG_CS0_MASK	0x003f0001
+#	define CFG_CS0_CTRL	0x1D00
+#else
+#	define CFG_CS0_BASE	0xFFE0
+#	define CFG_CS0_MASK	0x001f0001
+#	define CFG_CS0_CTRL	0x1D80
+#endif
+
+#endif				/* _M5329EVB_H */
diff --git a/include/configs/M5249EVB.h b/include/configs/M5249EVB.h
new file mode 100644
index 0000000..de7ea42
--- /dev/null
+++ b/include/configs/M5249EVB.h
@@ -0,0 +1,194 @@
+/*
+ * Configuation settings for the esd TASREG board.
+ *
+ * (C) Copyright 2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5249EVB_H
+#define _M5249EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF52x2			/* define processor family */
+#define CONFIG_M5249			/* define processor type */
+
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		19200
+#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef  CONFIG_WATCHDOG
+
+#undef CONFIG_MONITOR_IS_IN_RAM		/* no pre-loader required!!! ;-) */
+
+/*
+ * BOOTP options
+ */
+#undef CONFIG_BOOTP_BOOTFILESIZE
+#undef CONFIG_BOOTP_BOOTPATH
+#undef CONFIG_BOOTP_GATEWAY
+#undef CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_NET
+
+#define CFG_PROMPT		"=> "
+#define CFG_LONGHELP				/* undef to save memory		*/
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup	*/
+#define CONFIG_AUTO_COMPLETE	1	/* add autocompletion support	*/
+#define CONFIG_LOOPW		1	/* enable loopw command	*/
+#define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands	*/
+
+#define CFG_LOAD_ADDR		0x200000	/* default load address */
+
+#define CFG_MEMTEST_START	0x400
+#define CFG_MEMTEST_END		0x380000
+
+#define CFG_HZ			1000
+
+/*
+ * Clock configuration: enable only one of the following options
+ */
+
+#undef  CFG_PLL_BYPASS				/* bypass PLL for test purpose */
+#define CFG_FAST_CLK		1		/* MCF5249 can run at 140MHz   */
+#define	CFG_CLK			132025600	/* MCF5249 can run at 140MHz   */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CFG_MBAR		0x10000000	/* Register Base Addrs */
+#define	CFG_MBAR2		0x80000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x4000	/* Address of Environment Sector*/
+#define CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
+#define CFG_ENV_SECT_SIZE	0x2000 /* see README - env sector total size	*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_SIZE		16		/* SDRAM size in MB */
+#define CFG_FLASH_BASE		(CFG_CSAR0 << 16)
+
+#if 0 /* test-only */
+#define CONFIG_PRAM		512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
+#endif
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+
+#define CFG_MONITOR_LEN		0x20000
+#define CFG_MALLOC_LEN		(1 * 1024*1024)	/* Reserve 1 MB for malloc()	*/
+#define CFG_BOOTPARAMS_LEN	64*1024
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x1000000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+#	define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+
+/* CS0 - AMD Flash, address 0xffc00000 */
+#define	CFG_CSAR0		0xffe0
+#define	CFG_CSCR0		0x1980		/* WS=0110, AA=1, PS=10         */
+/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
+#define	CFG_CSMR0		0x003f0021	/* 4MB, AA=0, WP=0, C/I=1, V=1  */
+
+/* CS1 - FPGA, address 0xe0000000 */
+#define	CFG_CSAR1		0xe000
+#define	CFG_CSCR1		0x0d80		/* WS=0011, AA=1, PS=10         */
+#define	CFG_CSMR1		0x00010001	/* 128kB, AA=0, WP=0, C/I=0, V=1*/
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define	CFG_GPIO_FUNC		0x00000008	/* Set gpio pins: none          */
+#define	CFG_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54*/
+#define	CFG_GPIO_EN		0x00000008	/* Set gpio output enable       */
+#define	CFG_GPIO1_EN		0x00c70000	/* Set gpio output enable       */
+#define	CFG_GPIO_OUT		0x00000008	/* Set outputs to default state */
+#define	CFG_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
+#define CFG_GPIO1_LED		0x00400000	/* user led                     */
+
+#endif	/* M5249 */
diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h
new file mode 100644
index 0000000..48170e7
--- /dev/null
+++ b/include/configs/M5253EVBE.h
@@ -0,0 +1,212 @@
+/*
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * Hayden Fraser (Hayden.Fraser@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _M5253EVBE_H
+#define _M5253EVBE_H
+
+#define CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5253		/* define processor type */
+#define CONFIG_M5253EVBE	/* define board type */
+
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		19200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG		/* disable watchdog */
+
+#define CONFIG_BOOTDELAY	5
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#ifndef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#else
+#define CFG_ENV_ADDR		0xffe04000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#endif
+
+/*
+ * BOOTP options
+ */
+#undef CONFIG_BOOTP_BOOTFILESIZE
+#undef CONFIG_BOOTP_BOOTPATH
+#undef CONFIG_BOOTP_GATEWAY
+#undef CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_NET
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+
+/* ATA */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_IDE_RESET	1
+#define CONFIG_IDE_PREINIT	1
+#define CONFIG_ATAPI
+#undef CONFIG_LBA48
+
+#define CFG_IDE_MAXBUS		1
+#define CFG_IDE_MAXDEVICE	2
+
+#define CFG_ATA_BASE_ADDR	(CFG_MBAR2 + 0x800)
+#define CFG_ATA_IDE0_OFFSET	0
+
+#define CFG_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
+#define CFG_ATA_STRIDE		4	/* Interval between registers */
+#define _IO_BASE		0
+
+#define CFG_PROMPT		"=> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+
+#define CFG_LOAD_ADDR		0x00100000
+
+#define CFG_MEMTEST_START	0x400
+#define CFG_MEMTEST_END		0x380000
+
+#define CFG_HZ			1000
+
+#undef CFG_PLL_BYPASS		/* bypass PLL for test purpose */
+#define CFG_FAST_CLK
+#ifdef CFG_FAST_CLK
+#	define CFG_PLLCR	0x1243E054
+#	define CFG_CLK		140000000
+#else
+#	define CFG_PLLCR	0x135a4140
+#	define CFG_CLK		70000000
+#endif
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CFG_MBAR		0x10000000	/* Register Base Addrs */
+#define CFG_MBAR2		0x80000000	/* Module Base Addrs 2 */
+
+/*
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM */
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
+
+#ifdef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_MONITOR_BASE	0x20000
+#else
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#endif
+
+#define CFG_MONITOR_LEN		0x40000
+#define CFG_MALLOC_LEN		(256 << 10)
+#define CFG_BOOTPARAMS_LEN	(64*1024)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/* FLASH organization */
+#define CFG_FLASH_BASE		0xffe00000
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	35	/* max number of sectors on one chip */
+#define CFG_FLASH_ERASE_TOUT	1000
+
+#define CFG_FLASH_CFI		1
+#define CFG_FLASH_CFI_DRIVER	1
+#define CFG_FLASH_SIZE		0x200000
+#define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+
+/* Cache Configuration */
+#define CFG_CACHELINE_SIZE	16
+
+/* Port configuration */
+#define CFG_FECI2C		0xF0
+
+#define CFG_CSAR0		0xFFE0
+#define CFG_CSMR0		0x001F0021
+#define CFG_CSCR0		0x1D80
+
+#define CFG_CSAR1		0
+#define CFG_CSMR1		0
+#define CFG_CSCR1		0
+
+#define CFG_CSAR2		0
+#define CFG_CSMR2		0
+#define CFG_CSCR2		0
+
+#define CFG_CSAR3		0
+#define CFG_CSMR3		0
+#define CFG_CSCR3		0
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define CFG_GPIO_FUNC		0x00000008	/* Set gpio pins: none */
+#define CFG_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54 */
+#define CFG_GPIO_EN		0x00000008	/* Set gpio output enable */
+#define CFG_GPIO1_EN		0x00c70000	/* Set gpio output enable */
+#define CFG_GPIO_OUT		0x00000008	/* Set outputs to default state */
+#define CFG_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
+#define CFG_GPIO1_LED		0x00400000	/* user led */
+
+#endif				/* _M5253EVB_H */
diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h
index 885a882..798ec0c 100644
--- a/include/configs/M5271EVB.h
+++ b/include/configs/M5271EVB.h
@@ -31,7 +31,6 @@
 #ifndef _M5271EVB_H
 #define _M5271EVB_H
 
-#define DEBUG
 #undef DEBUG
 
 /*
@@ -41,29 +40,26 @@
 #define CONFIG_M5271		/* define processor type */
 #define CONFIG_M5271EVB		/* define board type */
 
-#define CONFIG_IPADDR		192.168.30.1
-#define CONFIG_SERVERIP		192.168.1.1
-#define CONFIG_ETHADDR		00:06:3b:01:41:55
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 
 #undef CONFIG_WATCHDOG		/* disable watchdog */
 
-#define CONFIG_BOOTDELAY	5
-
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
  */
 #ifndef CONFIG_MONITOR_IS_IN_RAM
 #define CFG_ENV_OFFSET		0x4000
-#define CFG_ENV_SECT_SIZE	0x2000
-#define CFG_ENV_IS_IN_FLASH	1
 #else
 #define CFG_ENV_ADDR		0xffe04000
+#endif
 #define CFG_ENV_SECT_SIZE	0x2000
 #define CFG_ENV_IS_IN_FLASH	1
-#endif
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*
  * BOOTP options
@@ -73,7 +69,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -81,22 +76,83 @@
 
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C		/* I2C with hw support */
+#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CFG_I2C_SPEED		80000
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x00000300
+#define CFG_IMMR		CFG_MBAR
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#define CONFIG_BOOTFILE		"u-boot.bin"
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_RETRY_COUNT	5
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* FEC_ENET */
+
+#define CONFIG_HOSTNAME		M5235EVB
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe2ffff;"		\
+	"era ffe00000 ffe2ffff;"				\
+	"cp.b ${loadaddr} 0 ${filesize};"	\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"=> "
-#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 
 #define CFG_LOAD_ADDR		0x00100000
 
@@ -114,16 +170,11 @@
 
 #define CFG_MBAR		0x40000000	/* Register Base Addrs */
 
-/* Enable FEC ethernet */
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT	5
-#define CFG_ENET_BD_BASE	0x480000
-
 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
 #define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
@@ -134,7 +185,7 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		16		/* SDRAM size in MB */
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 
 #ifdef	CONFIG_MONITOR_IS_IN_RAM
@@ -152,11 +203,11 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /* FLASH organization */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
 #define CFG_FLASH_ERASE_TOUT	1000
 
 #define CFG_FLASH_CFI		1
@@ -169,4 +220,4 @@
 /* Port configuration */
 #define CFG_FECI2C		0xF0
 
-#endif	/* _M5271EVB_H */
+#endif				/* _M5271EVB_H */
diff --git a/include/configs/M5272C3.h b/include/configs/M5272C3.h
index cc456dc..2b8734b 100644
--- a/include/configs/M5272C3.h
+++ b/include/configs/M5272C3.h
@@ -33,18 +33,20 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#define CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5272			/* define processor type */
+#define CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5272		/* define processor type */
 
-#define FEC_ENET
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
-#define CONFIG_WATCHDOG
+#undef CONFIG_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT 10000	/* timeout in milliseconds */
 
-#define CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
+#undef CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
 
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
@@ -60,7 +62,6 @@
 #define CFG_ENV_IS_IN_FLASH	1
 #endif
 
-
 /*
  * BOOTP options
  */
@@ -69,37 +70,82 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_MEMORY
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
-
 #define CONFIG_BOOTDELAY	5
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME		M5272C3
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"-> "
-#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 #define CFG_LOAD_ADDR		0x20000
-
 #define CFG_MEMTEST_START	0x400
 #define CFG_MEMTEST_END		0x380000
-
 #define CFG_HZ			1000
 #define CFG_CLK			66000000
 
@@ -108,20 +154,15 @@
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
-
 #define CFG_MBAR		0x10000000	/* Register Base Addrs */
-
 #define CFG_SCR			0x0003;
 #define CFG_SPR			0xffff;
 
-#define CFG_DISCOVER_PHY
-#define CFG_ENET_BD_BASE	0x380000
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
 #define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
@@ -132,7 +173,7 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		4		/* SDRAM size in MB */
+#define CFG_SDRAM_SIZE		4	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 
 #ifdef	CONFIG_MONITOR_IS_IN_RAM
@@ -150,13 +191,13 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
 #define CFG_FLASH_ERASE_TOUT	1000
 
 /*-----------------------------------------------------------------------
@@ -169,25 +210,18 @@
  */
 #define CFG_BR0_PRELIM		0xFFE00201
 #define CFG_OR0_PRELIM		0xFFE00014
-
 #define CFG_BR1_PRELIM		0
 #define CFG_OR1_PRELIM		0
-
 #define CFG_BR2_PRELIM		0x30000001
 #define CFG_OR2_PRELIM		0xFFF80000
-
 #define CFG_BR3_PRELIM		0
 #define CFG_OR3_PRELIM		0
-
 #define CFG_BR4_PRELIM		0
 #define CFG_OR4_PRELIM		0
-
 #define CFG_BR5_PRELIM		0
 #define CFG_OR5_PRELIM		0
-
 #define CFG_BR6_PRELIM		0
 #define CFG_OR6_PRELIM		0
-
 #define CFG_BR7_PRELIM		0x00000701
 #define CFG_OR7_PRELIM		0xFFC0007C
 
@@ -197,9 +231,8 @@
 #define CFG_PACNT		0x00000000
 #define CFG_PADDR		0x0000
 #define CFG_PADAT		0x0000
-#define CFG_PBCNT		0x55554155		/* Ethernet/UART configuration */
+#define CFG_PBCNT		0x55554155	/* Ethernet/UART configuration */
 #define CFG_PBDDR		0x0000
 #define CFG_PBDAT		0x0000
 #define CFG_PDCNT		0x00000000
-
-#endif	/* _M5272C3_H */
+#endif				/* _M5272C3_H */
diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h
index f2a7644..3c17c1e 100644
--- a/include/configs/M5282EVB.h
+++ b/include/configs/M5282EVB.h
@@ -33,15 +33,17 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#define	CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5282			/* define processor type */
+#define	CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5282		/* define processor type */
 
-#define FEC_ENET
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE 19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
-#define	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
+#undef	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
 
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
@@ -50,7 +52,6 @@
 #define CFG_ENV_SIZE		0x2000
 #define CFG_ENV_IS_IN_FLASH	1
 
-
 /*
  * BOOTP options
  */
@@ -59,29 +60,73 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 #define CONFIG_BOOTDELAY	5
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME		M5272C3
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"-> "
-#define	CFG_LONGHELP				/* undef to save memory		*/
+#define	CFG_LONGHELP		/* undef to save memory         */
 
 #if defined(CONFIG_CMD_KGDB)
-#define	CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define	CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 
 #define CFG_LOAD_ADDR		0x20000
 
@@ -91,6 +136,10 @@
 #define CFG_HZ			1000000
 #define	CFG_CLK			64000000
 
+/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
+
+#define CFG_MFD			0x02	/* PLL Multiplication Factor Devider */
+#define CFG_RFD			0x00	/* PLL Reduce Frecuency Devider */
 
 /*
  * Low Level Configuration Settings
@@ -99,15 +148,12 @@
  */
 #define	CFG_MBAR		0x40000000
 
-#undef	CFG_DISCOVER_PHY
-#define	CFG_ENET_BD_BASE	0x380000
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR       0x20000000
-#define CFG_INIT_RAM_END	0x10000		/* End of used area in internal SRAM	*/
-#define CFG_GBL_DATA_SIZE	64      	/* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM    */
+#define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
@@ -117,49 +163,88 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define	CFG_SDRAM_SIZE		4		/* SDRAM size in MB */
+#define	CFG_SDRAM_SIZE		8	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 #define	CFG_INT_FLASH_BASE	0xf0000000
+#define CFG_INT_FLASH_ENABLE	0x21
 
 /* If M5282 port is fully implemented the monitor base will be behind
  * the vector table. */
-/* #define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400) */
-#define CFG_MONITOR_BASE	0x20000
+#if (TEXT_BASE != CFG_INT_FLASH_BASE)
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#else
+#define CFG_MONITOR_BASE	(TEXT_BASE + 0x418)	/* 24 Byte for CFM-Config */
+#endif
 
 #define CFG_MONITOR_LEN		0x20000
 #define CFG_MALLOC_LEN		(256 << 10)
 #define CFG_BOOTPARAMS_LEN	64*1024
 
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define	CFG_MAX_FLASH_SECT	35
-#define	CFG_MAX_FLASH_BANKS	1
-#define	CFG_FLASH_ERASE_TOUT	10000000
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x1000000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+#	define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#endif
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	16
 
-
 /*-----------------------------------------------------------------------
  * Memory bank definitions
  */
-
-
+#define CFG_CS0_BASE		CFG_FLASH_BASE
+#define CFG_CS0_SIZE		2*1024*1024
+#define CFG_CS0_WIDTH		16
+#define CFG_CS0_RO 		0
+#define CFG_CS0_WS		6
+/*
+#define CFG_CS3_BASE		0xE0000000
+#define CFG_CS3_SIZE		1*1024*1024
+#define CFG_CS3_WIDTH		16
+#define CFG_CS3_RO 		0
+#define CFG_CS3_WS		6
+*/
 /*-----------------------------------------------------------------------
  * Port configuration
  */
+#define CFG_PACNT		0x0000000	/* Port A D[31:24] */
+#define CFG_PADDR		0x0000000
+#define CFG_PADAT		0x0000000
+
+#define CFG_PBCNT		0x0000000	/* Port B D[23:16] */
+#define CFG_PBDDR		0x0000000
+#define CFG_PBDAT		0x0000000
+
+#define CFG_PCCNT		0x0000000	/* Port C D[15:08] */
+#define CFG_PCDDR		0x0000000
+#define CFG_PCDAT		0x0000000
+
+#define CFG_PDCNT		0x0000000	/* Port D D[07:00] */
+#define CFG_PCDDR		0x0000000
+#define CFG_PCDAT		0x0000000
 
+#define CFG_PEHLPAR		0xC0
+#define CFG_PUAPAR		0x0F	/* UA0..UA3 = Uart 0 +1 */
+#define CFG_DDRUA		0x05
+#define CFG_PJPAR 		0xFF;
 
-#endif	/* _CONFIG_M5282EVB_H */
+#endif				/* _CONFIG_M5282EVB_H */
diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h
new file mode 100644
index 0000000..d3b1605
--- /dev/null
+++ b/include/configs/M5329EVB.h
@@ -0,0 +1,267 @@
+/*
+ * Configuation settings for the Freescale MCF5329 FireEngine board.
+ *
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5329EVB_H
+#define _M5329EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF532x		/* define processor family */
+#define CONFIG_M5329		/* define processor type */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT	5000	/* timeout in milliseconds, max timeout is 6.71sec */
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#ifdef NANDFLASH_SIZE
+#      define CONFIG_CMD_NAND
+#endif
+
+#define CFG_UNIFY_CACHE
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+#define CONFIG_MCFRTC
+#undef RTC_DEBUG
+
+/* Timer */
+#define CONFIG_MCFTMR
+#undef CONFIG_MCFPIT
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C			/* I2C with hw support */
+#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		80000
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x58000
+#define CFG_IMMR		CFG_MBAR
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#define CONFIG_UDP_CHECKSUM
+
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* FEC_ENET */
+
+#define CONFIG_HOSTNAME		M5329EVB
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"			\
+	"loadaddr=40010000\0"	\
+	"u-boot=u-boot.bin\0"	\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"	\
+	"prog=prot off 0 2ffff;"	\
+	"era 0 2ffff;"	\
+	"cp.b ${loadaddr} 0 ${filesize};"	\
+	"save\0"	\
+	""
+
+#define CONFIG_PRAM		512	/* 512 KB */
+#define CFG_PROMPT		"-> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#ifdef CONFIG_CMD_KGDB
+#	define CFG_CBSIZE	1024	/* Console I/O Buffer Size */
+#else
+#	define CFG_CBSIZE	256	/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE			(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
+#define CFG_LOAD_ADDR		0x40010000
+
+#define CFG_HZ			1000
+#define CFG_CLK			80000000
+#define CFG_CPU_CLK		CFG_CLK * 3
+
+#define CFG_MBAR		0xFC000000
+
+#define CFG_LATCH_ADDR		(CFG_CS1_BASE + 0x80000)
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x80000000
+#define CFG_INIT_RAM_END	0x8000	/* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL	0x221
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 0x10)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x40000000
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
+#define CFG_SDRAM_CFG1		0x53722730
+#define CFG_SDRAM_CFG2		0x56670000
+#define CFG_SDRAM_CTRL		0xE1092000
+#define CFG_SDRAM_EMOD		0x40010000
+#define CFG_SDRAM_MODE		0x018D0000
+
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END		((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+
+#define CFG_BOOTPARAMS_LEN	64*1024
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x800000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#endif
+
+#ifdef NANDFLASH_SIZE
+#	define CFG_MAX_NAND_DEVICE	1
+#	define CFG_NAND_BASE		(CFG_CS2_BASE << 16)
+#	define CFG_NAND_SIZE		1
+#	define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#	define NAND_MAX_CHIPS		1
+#	define NAND_ALLOW_ERASE_ALL	1
+#	define CONFIG_JFFS2_NAND	1
+#	define CONFIG_JFFS2_DEV		"nand0"
+#	define CONFIG_JFFS2_PART_SIZE	(CFG_CS2_MASK & ~1)
+#	define CONFIG_JFFS2_PART_OFFSET	0x00000000
+#endif
+
+#define CFG_FLASH_BASE		(CFG_CS0_BASE << 16)
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_IS_EMBEDDED	1
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16
+
+/*-----------------------------------------------------------------------
+ * Chipselect bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - CompactFlash and registers
+ * CS2 - NAND Flash 16, 32, or 64MB
+ * CS3 - Available
+ * CS4 - Available
+ * CS5 - Available
+ */
+#define CFG_CS0_BASE		0
+#define CFG_CS0_MASK		0x007f0001
+#define CFG_CS0_CTRL		0x00001fa0
+
+#define CFG_CS1_BASE		0x1000
+#define CFG_CS1_MASK		0x001f0001
+#define CFG_CS1_CTRL		0x002A3780
+
+#ifdef NANDFLASH_SIZE
+#define CFG_CS2_BASE		0x2000
+#define CFG_CS2_MASK		((NANDFLASH_SIZE << 20) | 1)
+#define CFG_CS2_CTRL		0x00001f60
+#endif
+
+#endif				/* _M5329EVB_H */
diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h
new file mode 100644
index 0000000..6f4859c
--- /dev/null
+++ b/include/configs/M54455EVB.h
@@ -0,0 +1,391 @@
+/*
+ * Configuation settings for the Freescale MCF54455 EVB board.
+ *
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _JAMICA54455_H
+#define _JAMICA54455_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF5445x		/* define processor family */
+#define CONFIG_M54455		/* define processor type */
+#define CONFIG_M54455EVB	/* M54455EVB board */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG
+
+#define CONFIG_TIMESTAMP	/* Print image info with timestamp */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+
+/* Network configuration */
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI	1
+#	define CONFIG_MII		1
+#	define CONFIG_CF_DOMII
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX	0
+#	define CFG_FEC1_PINMUX	0
+#	define CFG_FEC0_MIIBASE	CFG_FEC0_IOBASE
+#	define CFG_FEC1_MIIBASE	CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 50000
+#	define CONFIG_HAS_ETH1
+
+#	define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#	define CONFIG_BOOTARGS		"root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=physmap-flash.0:5M(kernel)ro,-(jffs2)"
+#	define CONFIG_ETHADDR		00:e0:0c:bc:e5:60
+#	define CONFIG_ETH1ADDR		00:e0:0c:bc:e5:61
+#	define CONFIG_ETHPRIME		"FEC0"
+#	define CONFIG_IPADDR		192.162.1.2
+#	define CONFIG_NETMASK		255.255.255.0
+#	define CONFIG_SERVERIP		192.162.1.1
+#	define CONFIG_GATEWAYIP		192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+#define CONFIG_HOSTNAME		M54455EVB
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"inpclk=" MK_STR(CFG_INPUT_CLKSRC) "\0"	\
+	"loadaddr=40010000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off 0 2ffff;"		\
+	"era 0 2ffff;"				\
+	"cp.b ${loadaddr} 0 ${filesize};"	\
+	"save\0"				\
+	""
+
+/* ATA configuration */
+#define CONFIG_ISO_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_IDE_RESET	1
+#define CONFIG_IDE_PREINIT	1
+#define CONFIG_ATAPI
+#undef CONFIG_LBA48
+
+#define CFG_IDE_MAXBUS		1
+#define CFG_IDE_MAXDEVICE	2
+
+#define CFG_ATA_BASE_ADDR	0x90000000
+#define CFG_ATA_IDE0_OFFSET	0
+
+#define CFG_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O                            */
+#define CFG_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers           */
+#define CFG_ATA_STRIDE		4	/* Interval between registers                 */
+#define _IO_BASE		0
+
+/* Realtime clock */
+#define CONFIG_MCFRTC
+#undef RTC_DEBUG
+#define CFG_RTC_OSCILLATOR	(32 * CFG_HZ)
+
+/* Timer */
+#define CONFIG_MCFTMR
+#undef CONFIG_MCFPIT
+
+/* I2c */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged               */
+#define CFG_I2C_SPEED		80000	/* I2C speed and slave address  */
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x58000
+#define CFG_IMMR		CFG_MBAR
+
+/* PCI */
+#define CONFIG_PCI		1
+
+#define CFG_PCI_MEM_BUS		0xA0000000
+#define CFG_PCI_MEM_PHYS	CFG_PCI_MEM_BUS
+#define CFG_PCI_MEM_SIZE	0x10000000
+
+#define CFG_PCI_IO_BUS		0xB1000000
+#define CFG_PCI_IO_PHYS		CFG_PCI_IO_BUS
+#define CFG_PCI_IO_SIZE		0x01000000
+
+#define CFG_PCI_CFG_BUS		0xB0000000
+#define CFG_PCI_CFG_PHYS	CFG_PCI_CFG_BUS
+#define CFG_PCI_CFG_SIZE	0x01000000
+
+/* FPGA - Spartan 2 */
+/* experiment
+#define CONFIG_FPGA		CFG_SPARTAN3
+#define CONFIG_FPGA_COUNT	1
+#define CFG_FPGA_PROG_FEEDBACK
+#define CFG_FPGA_CHECK_CTRLC
+*/
+
+/* Input, PCI, Flexbus, and VCO */
+#define CONFIG_EXTRA_CLOCK
+
+#define CONFIG_PRAM		512	/* 512 KB */
+
+#define CFG_PROMPT		"-> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE			1024	/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE			256	/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
+
+#define CFG_LOAD_ADDR		(CFG_SDRAM_BASE + 0x10000)
+
+#define CFG_HZ			1000
+
+#define CFG_MBAR		0xFC000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x80000000
+#define CFG_INIT_RAM_END	0x8000	/* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL	0x221
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 16)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x40000000
+#define CFG_SDRAM_BASE1		0x48000000
+#define CFG_SDRAM_SIZE		256	/* SDRAM size in MB */
+#define CFG_SDRAM_CFG1		0x65311610
+#define CFG_SDRAM_CFG2		0x59670000
+#define CFG_SDRAM_CTRL		0xEA0B2000
+#define CFG_SDRAM_EMOD		0x40010000
+#define CFG_SDRAM_MODE		0x00010033
+
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END		((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#define CFG_BOOTPARAMS_LEN	64*1024
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_OVERWRITE	1
+#undef CFG_ENV_IS_EMBEDDED
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#ifdef CFG_ATMEL_BOOT
+#	define CFG_FLASH_BASE		0
+#	define CFG_FLASH0_BASE		CFG_CS0_BASE
+#	define CFG_FLASH1_BASE		CFG_CS1_BASE
+#else
+#	define CFG_FLASH_BASE		CFG_FLASH0_BASE
+#	define CFG_FLASH0_BASE		CFG_CS1_BASE
+#	define CFG_FLASH1_BASE		CFG_CS0_BASE
+#endif
+
+/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system
+/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system
+   keep reset. */
+#undef CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x1000000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
+#	define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+#	define CFG_FLASH_BANKS_LIST	{ CFG_CS0_BASE, CFG_CS1_BASE }
+
+#else
+
+#	define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+
+#	define CFG_ATMEL_REGION		4
+#	define CFG_ATMEL_TOTALSECT	11
+#	define CFG_ATMEL_SECT		{1, 2, 1, 7}
+#	define CFG_ATMEL_SECTSZ		{0x4000, 0x2000, 0x8000, 0x10000}
+#	define CFG_INTEL_SECT		137
+
+/* max number of sectors on one chip */
+#	define CFG_MAX_FLASH_SECT	(CFG_ATMEL_TOTALSECT + CFG_INTEL_SECT)
+#	define CFG_FLASH_ERASE_TOUT	2000	/* Atmel needs longer timeout */
+#	define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
+#	define CFG_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
+#	define CFG_FLASH_UNLOCK_TOUT	100	/* Timeout for Flash Clear Lock Bits (in ms) */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+
+#endif
+
+/*
+ * This is setting for JFFS2 support in u-boot.
+ * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
+ */
+#ifdef CFG_ATMEL_BOOT
+#	define CONFIG_JFFS2_DEV		"nor0"
+#	define CONFIG_JFFS2_PART_SIZE	0x01000000
+#	define CONFIG_JFFS2_PART_OFFSET	CFG_FLASH1_BASE
+#else
+#	define CONFIG_JFFS2_DEV		"nor0"
+#	define CONFIG_JFFS2_PART_SIZE	(0x01000000 - 0x500000)
+#	define CONFIG_JFFS2_PART_OFFSET	(CFG_FLASH0_BASE + 0x500000)
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE		16
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - CompactFlash and registers
+ * CS2 - CPLD
+ * CS3 - FPGA
+ * CS4 - Available
+ * CS5 - Available
+ */
+
+#ifdef CFG_ATMEL_BOOT
+ /* Atmel Flash */
+#define CFG_CS0_BASE		0
+#define CFG_CS0_MASK		0x00070001
+#define CFG_CS0_CTRL		0x00001140
+/* Intel Flash */
+#define CFG_CS1_BASE		0x04000000
+#define CFG_CS1_MASK		0x01FF0001
+#define CFG_CS1_CTRL		0x003F3D60
+
+#define CFG_ATMEL_BASE		CFG_CS0_BASE
+#else
+/* Intel Flash */
+#define CFG_CS0_BASE		0
+#define CFG_CS0_MASK		0x01FF0001
+#define CFG_CS0_CTRL		0x003F3D60
+ /* Atmel Flash */
+#define CFG_CS1_BASE		0x04000000
+#define CFG_CS1_MASK		0x00070001
+#define CFG_CS1_CTRL		0x00001140
+
+#define CFG_ATMEL_BASE		CFG_CS1_BASE
+#endif
+
+/* CPLD */
+#define CFG_CS2_BASE		0x08000000
+#define CFG_CS2_MASK		0x00070001
+#define CFG_CS2_CTRL		0x003f1140
+
+/* FPGA */
+#define CFG_CS3_BASE		0x09000000
+#define CFG_CS3_MASK		0x00070001
+#define CFG_CS3_CTRL		0x00000020
+
+#endif				/* _JAMICA54455_H */
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h
index 81db96f..6568fe1 100644
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB.h
@@ -113,12 +113,12 @@
 				/* 0x03200064 */
 #if defined(CONFIG_DDR_2T_TIMING)
 #define CFG_SDRAM_CFG		( SDRAM_CFG_SREN \
-				| 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_2T_EN \
 				| SDRAM_CFG_DBW_32 )
 #else
 #define CFG_SDRAM_CFG		( SDRAM_CFG_SREN \
-				| 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_32_BE )
 				/* 0x43080000 */
 #endif
@@ -228,12 +228,9 @@
 #define CFG_LBLAWAR3_PRELIM	0x8000000E	/* 32KB  */
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8313@0"
 #define OF_SOC			"soc8313@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -310,6 +307,8 @@
 #define CONFIG_TSEC2_NAME	"TSEC1"
 #define TSEC1_PHY_ADDR			0x1c
 #define TSEC2_PHY_ADDR			4
+#define TSEC1_FLAGS			TSEC_GIGABIT
+#define TSEC2_FLAGS			TSEC_GIGABIT
 #define TSEC1_PHYIDX			0
 #define TSEC2_PHYIDX			0
 
@@ -507,6 +506,7 @@
 
 #define CONFIG_ETHADDR		00:E0:0C:00:95:01
 #define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETH1ADDR		00:E0:0C:00:95:02
 
 #define CONFIG_IPADDR		10.0.0.2
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
new file mode 100644
index 0000000..376973b
--- /dev/null
+++ b/include/configs/MPC8323ERDB.h
@@ -0,0 +1,583 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 family */
+#define CONFIG_QE		1	/* Has QE */
+#define CONFIG_MPC83XX		1	/* MPC83xx family */
+#define CONFIG_MPC832X		1	/* MPC832x CPU specific */
+
+#define CONFIG_PCI		1
+#define CONFIG_83XX_GENERIC_PCI	1
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN	66666667	/* in Hz */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+#endif
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CFG_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+	HRCWL_DDR_TO_SCB_CLK_2X1 |\
+	HRCWL_VCO_1X2 |\
+	HRCWL_CSB_TO_CLKIN_2X1 |\
+	HRCWL_CORE_TO_CSB_2_5X1 |\
+	HRCWL_CE_PLL_VCO_DIV_2 |\
+	HRCWL_CE_PLL_DIV_1X1 |\
+	HRCWL_CE_TO_PLL_1X3)
+
+#define CFG_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0X00000100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_BIG_ENDIAN |\
+	HRCWH_LALE_NORMAL)
+
+/*
+ * System IO Config
+ */
+#define CFG_SICRL		0x00000000
+
+#define CONFIG_BOARD_EARLY_INIT_F	/* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CFG_IMMR		0xE0000000
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE		0x00000000	/* DDR is system memory */
+#define CFG_SDRAM_BASE		CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE
+#define CFG_DDRCDR		0x73000002	/* DDR II voltage is 1.8V */
+
+#undef CONFIG_SPD_EEPROM
+#if defined(CONFIG_SPD_EEPROM)
+/* Determine DDR configuration from I2C interface
+ */
+#define SPD_EEPROM_ADDRESS	0x51	/* DDR SODIMM */
+#else
+/* Manually set up DDR parameters
+ */
+#define CFG_DDR_SIZE		64	/* MB */
+#define CFG_DDR_CS0_CONFIG	0x80840101
+#define CFG_DDR_TIMING_0	0x00220802
+#define CFG_DDR_TIMING_1	0x3935d322
+#define CFG_DDR_TIMING_2	0x0f9048ca
+#define CFG_DDR_TIMING_3	0x00000000
+#define CFG_DDR_CLK_CNTL	0x02000000
+#define CFG_DDR_MODE		0x44400232
+#define CFG_DDR_MODE2		0x8000c000
+#define CFG_DDR_INTERVAL	0x03200064
+#define CFG_DDR_CS0_BNDS	0x00000003
+#define CFG_DDR_SDRAM_CFG	0x43080000
+#define CFG_DDR_SDRAM_CFG2	0x00401000
+#endif
+
+/*
+ * Memory test
+ */
+#undef CFG_DRAM_TEST		/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00030000	/* memtest region */
+#define CFG_MEMTEST_END		0x03f00000
+
+/*
+ * The reserved memory
+ */
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef  CFG_RAMBOOT
+#endif
+
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0xE6000000	/* Initial RAM address */
+#define CFG_INIT_RAM_END	0x1000		/* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE	0x100		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CFG_LCRR		(LCRR_DBYP | LCRR_CLKDIV_2)
+#define CFG_LBC_LBCR		0x00000000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI		/* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER	/* use the CFI driver */
+#define CFG_FLASH_BASE		0xFE000000	/* FLASH base address */
+#define CFG_FLASH_SIZE		16	/* FLASH size is 16M */
+
+#define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE	/* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM	0x80000018	/* 32MB window size */
+
+#define CFG_BR0_PRELIM	(CFG_FLASH_BASE |	/* Flash Base address */ \
+			(2 << BR_PS_SHIFT) |	/* 16 bit port size */ \
+			BR_V)			/* valid */
+#define CFG_OR0_PRELIM		0xfe006ff7	/* 16MB Flash size */
+
+#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
+#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+
+/*
+ * SDRAM on the Local Bus
+ */
+#undef CFG_LB_SDRAM		/* The board has not SRDAM on local bus */
+
+#ifdef CFG_LB_SDRAM
+#define CFG_LBC_SDRAM_BASE	0xF0000000	/* SDRAM base address */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+
+#define CFG_LBLAWBAR2_PRELIM	CFG_LBC_SDRAM_BASE
+#define CFG_LBLAWAR2_PRELIM	0x80000019	/* 64MB */
+
+/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ *    port size = 32-bits = BR2[19:20] = 11
+ *    no parity checking = BR2[21:22] = 00
+ *    SDRAM for MSEL = BR2[24:26] = 011
+ *    Valid = BR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM	0xf0001861	/*Port size=32bit, MSEL=SDRAM */
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ *    64MB mask for AM, OR2[0:7] = 1111 1100
+ *                 XAM, OR2[17:18] = 11
+ *    9 columns OR2[19-21] = 010
+ *    13 rows   OR2[23-25] = 100
+ *    EAD set for extra time OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
+#define CFG_OR2_PRELIM	0xfc006901
+
+#define CFG_LBC_LSRT	0x32000000	/* LB sdram refresh timer, about 6us */
+#define CFG_LBC_MRTPR	0x20000000	/* LB refresh timer prescal, 266MHz/32 */
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON	0x0063b723
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_NORMAL)
+
+#endif
+
+/*
+ * Windows to access PIB via local bus
+ */
+#define CFG_LBLAWBAR3_PRELIM	0xf8008000	/* windows base 0xf8008000 */
+#define CFG_LBLAWAR3_PRELIM	0x8000000f	/* windows size 64KB */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1	(CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2	(CFG_IMMR+0x4600)
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+#define OF_CPU			"PowerPC,8323@0"
+#define OF_SOC			"soc8323@e0000000"
+#define OF_QE			"qe@e0100000"
+#define OF_TBCLK		(bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH		"/soc8323@e0000000/serial@4500"
+
+/* I2C */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CONFIG_FSL_I2C
+#define CFG_I2C_SPEED	400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE	0x7F
+#define CFG_I2C_NOPROBES	{0x51}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET	0x3000
+
+/*
+ * Config on-board RTC
+ */
+#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
+#define CFG_I2C_RTC_ADDR	0x68	/* at address 0x68 */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_MMIO_BASE	0x90000000
+#define CFG_PCI1_MMIO_PHYS	CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_IO_BASE		0xd0000000
+#define CFG_PCI1_IO_PHYS		CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE		0x04000000	/* 64M */
+
+#ifdef CONFIG_PCI
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */
+
+#endif	/* CONFIG_PCI */
+
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI	1
+#endif
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME		"Freescale GETH"
+
+#define CONFIG_UEC_ETH1		/* ETH3 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM	2	/* UCC3 */
+#define CFG_UEC1_RX_CLK		QE_CLK9
+#define CFG_UEC1_TX_CLK		QE_CLK10
+#define CFG_UEC1_ETH_TYPE	FAST_ETH
+#define CFG_UEC1_PHY_ADDR	4
+#define CFG_UEC1_INTERFACE_MODE	ENET_100_MII
+#endif
+
+#define CONFIG_UEC_ETH2		/* ETH4 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM	1	/* UCC2 */
+#define CFG_UEC2_RX_CLK		QE_CLK16
+#define CFG_UEC2_TX_CLK		QE_CLK3
+#define CFG_UEC2_ETH_TYPE	FAST_ETH
+#define CFG_UEC2_PHY_ADDR	0
+#define CFG_UEC2_INTERFACE_MODE	ENET_100_MII
+#endif
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+	#define CFG_ENV_IS_IN_FLASH	1
+	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+	#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+	#define CFG_ENV_SIZE		0x2000
+#else
+	#define CFG_NO_FLASH		1	/* Flash is not usable now */
+	#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
+	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+	#define CFG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ASKENV
+
+#if defined(CONFIG_PCI)
+	#define CONFIG_CMD_PCI
+#endif
+#if defined(CFG_RAMBOOT)
+	#undef CONFIG_CMD_ENV
+	#undef CONFIG_CMD_LOADS
+#endif
+
+#undef CONFIG_WATCHDOG		/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP		/* undef to save memory */
+#define CFG_LOAD_ADDR		0x2000000	/* default load address */
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt */
+
+#if (CONFIG_CMD_KGDB)
+	#define CFG_CBSIZE	1024	/* Console I/O Buffer Size */
+#else
+	#define CFG_CBSIZE	256	/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CFG_HID0_INIT		0x000000000
+#define CFG_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
+#define CFG_HID2		HID2_HBE
+
+/*
+ * Cache Config
+ */
+#define CFG_DCACHE_SIZE		16384
+#define CFG_CACHELINE_SIZE	32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value */
+#endif
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L	CFG_IBAT0L
+#define CFG_DBAT0U	CFG_IBAT0U
+
+/* IMMRBAR & PCI IO: cache-inhibit and guarded */
+#define CFG_IBAT1L	(CFG_IMMR | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT1U	(CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L	CFG_IBAT1L
+#define CFG_DBAT1U	CFG_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CFG_IBAT2L	(CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT2U	(CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L	(CFG_FLASH_BASE | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U	CFG_IBAT2U
+
+#define CFG_IBAT3L	(0)
+#define CFG_IBAT3U	(0)
+#define CFG_DBAT3L	CFG_IBAT3L
+#define CFG_DBAT3U	CFG_IBAT3U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CFG_IBAT4L	(CFG_INIT_RAM_ADDR | BATL_PP_10)
+#define CFG_IBAT4U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT4L	CFG_IBAT4L
+#define CFG_DBAT4U	CFG_IBAT4U
+
+#ifdef CONFIG_PCI
+/* PCI MEM space: cacheable */
+#define CFG_IBAT5L	(CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT5U	(CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT5L	CFG_IBAT5L
+#define CFG_DBAT5U	CFG_IBAT5U
+/* PCI MMIO space: cache-inhibit and guarded */
+#define CFG_IBAT6L	(CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT6U	(CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L	CFG_IBAT6L
+#define CFG_DBAT6U	CFG_IBAT6U
+#else
+#define CFG_IBAT5L	(0)
+#define CFG_IBAT5U	(0)
+#define CFG_IBAT6L	(0)
+#define CFG_IBAT6U	(0)
+#define CFG_DBAT5L	CFG_IBAT5L
+#define CFG_DBAT5U	CFG_IBAT5U
+#define CFG_DBAT6L	CFG_IBAT6L
+#define CFG_DBAT6U	CFG_IBAT6U
+#endif
+
+/* Nothing in BAT7 */
+#define CFG_IBAT7L	(0)
+#define CFG_IBAT7U	(0)
+#define CFG_DBAT7L	CFG_IBAT7L
+#define CFG_DBAT7U	CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+
+#if (CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ETHADDR	00:04:9f:ef:03:01
+#define CONFIG_HAS_ETH1				/* add support for "eth1addr" */
+#define CONFIG_ETH1ADDR	00:04:9f:ef:03:02
+
+#define CONFIG_IPADDR		10.0.0.2
+#define CONFIG_SERVERIP		10.0.0.1
+#define CONFIG_GATEWAYIP	10.0.0.1
+#define CONFIG_NETMASK		255.0.0.0
+#define CONFIG_NETDEV		eth1
+
+#define CONFIG_HOSTNAME		mpc8323erdb
+#define CONFIG_ROOTPATH		/nfsroot
+#define CONFIG_RAMDISKFILE	rootfs.ext2.gz.uboot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
+#define CONFIG_FDTFILE		mpc832x_rdb.dtb
+
+#define CONFIG_LOADADDR		200000	/* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY	-1	/* -1 disables auto-boot */
+#define CONFIG_BAUDRATE		115200
+
+#define XMK_STR(x)	#x
+#define MK_STR(x)	XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
+	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+	"tftpflash=tftp $loadaddr $uboot;"				\
+		"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+		"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+		"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+		"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+		"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+	"fdtaddr=400000\0"						\
+	"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"				\
+	"ramdiskaddr=1000000\0"						\
+	"ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0"			\
+	"console=ttyS0\0"						\
+	"setbootargs=setenv bootargs "					\
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath "	\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv rootdev /dev/nfs;"					\
+	"run setbootargs;"						\
+	"run setipargs;"						\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+	"setenv rootdev /dev/ram;"					\
+	"run setbootargs;"						\
+	"tftp $ramdiskaddr $ramdiskfile;"				\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index f62ca2c..c9c6d88 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -30,6 +30,8 @@
 #define CONFIG_MPC83XX		1	/* MPC83xx family */
 #define CONFIG_MPC832X		1	/* MPC832x CPU specific */
 #define CONFIG_MPC832XEMDS	1	/* MPC832XEMDS board specific */
+#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
+#undef CONFIG_PQ_MDS_PIB_ATM	/* QOC3 ATM card */
 
 /*
  * System Clock Setup
@@ -87,6 +89,7 @@
 #define CFG_SICRL		0x00000000
 
 #define CONFIG_BOARD_EARLY_INIT_F	/* call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
 
 /*
  * IMMR new address
@@ -315,12 +318,9 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8323@0"
 #define OF_SOC			"soc8323@e0000000"
 #define OF_QE			"qe@e0100000"
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 1567fcf..92555ba 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -339,12 +339,9 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8349@0"
 #define OF_SOC			"soc8349@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -440,6 +437,8 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -699,6 +698,7 @@
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_ETHADDR		00:04:9f:ef:23:33
 #define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETH1ADDR		00:E0:0C:00:7E:21
 #endif
 
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
index 121ff06..54cab52 100644
--- a/include/configs/MPC8349ITX.h
+++ b/include/configs/MPC8349ITX.h
@@ -289,18 +289,16 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 
+#define CONFIG_CONSOLE		ttyS0
 #define CONFIG_BAUDRATE		115200
 
 #define CFG_NS16550_COM1	(CFG_IMMR + 0x4500)
 #define CFG_NS16550_COM2	(CFG_IMMR + 0x4600)
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8349@0"
 #define OF_SOC			"soc8349@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -377,10 +375,12 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_TSEC1
 
 #ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME  "TSEC0"
 #define CFG_TSEC1_OFFSET	0x24000
 #define TSEC1_PHY_ADDR		0x1c	/* VSC8201 uses address 0x1c */
 #define TSEC1_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
 #endif
 
 #ifdef CONFIG_TSEC2
@@ -390,6 +390,7 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_UNKNOWN_TSEC	/* TSEC2 is proprietary */
 #define TSEC2_PHY_ADDR		4
 #define TSEC2_PHYIDX		0
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #endif
 
 #define CONFIG_ETHPRIME		"Freescale TSEC"
@@ -408,6 +409,7 @@ boards, we say we have two, but don't display a message if we find only one. */
   #define CFG_ENV_SIZE		0x2000
 #else
   #define CFG_NO_FLASH		/* Flash is not usable now */
+  #undef  CFG_FLASH_CFI_DRIVER
   #define CFG_ENV_IS_NOWHERE	/* Store ENV in memory only */
   #define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
   #define CFG_ENV_SIZE		0x2000
@@ -450,9 +452,7 @@ boards, we say we have two, but don't display a message if we find only one. */
     #define CONFIG_CMD_I2C
 #endif
 
-
 /* Watchdog */
-
 #undef CONFIG_WATCHDOG		/* watchdog disabled */
 
 /*
@@ -673,9 +673,10 @@ boards, we say we have two, but don't display a message if we find only one. */
 	" ip=" MK_STR(CONFIG_IPADDR) ":" MK_STR(CONFIG_SERVERIP) ":" 	\
 		MK_STR(CONFIG_GATEWAYIP) ":" MK_STR(CONFIG_NETMASK) ":" \
 		MK_STR(CONFIG_HOSTNAME) ":" MK_STR(CONFIG_NETDEV) ":off" \
-	" console=ttyS0," MK_STR(CONFIG_BAUDRATE)
+	" console=" MK_STR(CONFIG_CONSOLE) "," MK_STR(CONFIG_BAUDRATE)
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
+	"console=" MK_STR(CONFIG_CONSOLE) "\0" 				\
 	"netdev=" MK_STR(CONFIG_NETDEV) "\0" 				\
 	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" 				\
 	"tftpflash=tftpboot $loadaddr $uboot; " 			\
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index 4b32a14..41f062c 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -32,6 +32,8 @@
 #define CONFIG_MPC83XX		1 /* MPC83XX family */
 #define CONFIG_MPC8360		1 /* MPC8360 CPU specific */
 #define CONFIG_MPC8360EMDS	1 /* MPC8360EMDS board specific */
+#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
+#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */
 
 /*
  * System Clock Setup
@@ -88,6 +90,7 @@
 #define CFG_SICRL		0x40000000
 
 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
 
 /*
  * IMMR new address
@@ -309,13 +312,13 @@
 /*
  * CS4 on Local Bus, to PIB
  */
-#define CFG_BR4_PRELIM	0xf8008801 /* CS4 base address at 0xf8008000 */
+#define CFG_BR4_PRELIM	0xf8010801 /* CS4 base address at 0xf8010000 */
 #define CFG_OR4_PRELIM	0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
 
 /*
  * CS5 on Local Bus, to PIB
  */
-#define CFG_BR5_PRELIM	0xf8010801 /* CS5 base address at 0xf8010000 */
+#define CFG_BR5_PRELIM	0xf8008801 /* CS5 base address at 0xf8008000 */
 #define CFG_OR5_PRELIM	0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
 
 /*
@@ -348,10 +351,6 @@
 #define CONFIG_OF_HAS_BD_T	1
 #define CONFIG_OF_HAS_UBOOT_ENV	1
 
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8360@0"
 #define OF_SOC			"soc8360@e0000000"
 #define OF_QE			"qe@e0100000"
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 5a7c879..be603ac 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -301,9 +301,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8540@0"
 #define OF_SOC			"soc8540@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -374,6 +371,8 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 
 #if CONFIG_HAS_FEC
@@ -381,6 +380,7 @@
 #define CONFIG_MPC85XX_FEC_NAME		"FEC"
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
+#define FEC_FLAGS		0
 #endif
 
 /* Options are: TSEC[0-1], FEC */
@@ -489,6 +489,7 @@
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h
index 0ce25cf..e376c11 100644
--- a/include/configs/MPC8540EVAL.h
+++ b/include/configs/MPC8540EVAL.h
@@ -213,10 +213,13 @@
 #define CONFIG_NET_MULTI 	1
 #define CONFIG_MII		1	/* MII PHY management	*/
 #define CONFIG_TSEC1    1
+#define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME      "TSEC0"
 #define CONFIG_TSEC2	1
+#define CONFIG_HAS_ETH1
 #define CONFIG_TSEC2_NAME      "TSEC1"
 #define CONFIG_MPC85XX_FEC      1
+#define CONFIG_HAS_ETH2
 #define CONFIG_MPC85XX_FEC_NAME                "FEC"
 #define TSEC1_PHY_ADDR          7
 #define	TSEC2_PHY_ADDR		4
@@ -224,6 +227,10 @@
 #define TSEC1_PHYIDX            0
 #define TSEC2_PHYIDX            0
 #define FEC_PHYIDX              0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define FEC_FLAGS		0
+
 /* Options are: TSEC[0-1], FEC */
 #define CONFIG_ETHPRIME                "TSEC0"
 
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index 50d3b6b..4e061bd 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -312,9 +312,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8541@0"
 #define OF_SOC			"soc8541@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -350,6 +347,13 @@ extern unsigned long get_clock_freq(void);
 #define CFG_PCI2_IO_PHYS	0xe2100000
 #define CFG_PCI2_IO_SIZE	0x100000	/* 1M */
 
+#ifdef CONFIG_LEGACY
+#define BRIDGE_ID 17
+#define VIA_ID 2
+#else
+#define BRIDGE_ID 28
+#define VIA_ID 4
+#endif
 
 #if defined(CONFIG_PCI)
 
@@ -377,13 +381,12 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
-#define FEC_PHY_ADDR		3
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
-#define FEC_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -475,6 +478,7 @@ extern unsigned long get_clock_freq(void);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index d0f94a3..f580cca 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -34,14 +34,14 @@
 #define CONFIG_MPC8544		1
 #define CONFIG_MPC8544DS	1
 
-#undef CONFIG_PCI			/* Enable PCI/PCIE */
-#undef CONFIG_PCI1			/* PCI controller 1 */
-#undef CONFIG_PCIE1			/* PCIE controler 1 (slot 1) */
-#undef CONFIG_PCIE2			/* PCIE controler 2 (slot 2) */
-#undef CONFIG_PCIE3			/* PCIE controler 3 (ULI bridge) */
-#undef CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
-
-#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCI1		1	/* PCI controller 1 */
+#define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE3		1	/* PCIE controler 3 (ULI bridge) */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #undef CONFIG_DDR_DLL
@@ -52,6 +52,7 @@
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 
 #define CONFIG_DDR_ECC_CMD
+#define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
 /*
  * When initializing flash, if we cannot find the manufacturer ID,
@@ -70,7 +71,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
-#define CONFIG_L2_CACHE			/* toggle L2 cache 	*/
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
 #define CONFIG_BTB			/* toggle branch predition */
 #define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
 #define CONFIG_CLEAR_LAW0		/* Clear LAW0 in cpu_init_r */
@@ -86,13 +87,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_MEMTEST_START	0x00200000	/* memtest works on */
 #define CFG_MEMTEST_END		0x00400000
 #define CFG_ALT_MEMTEST
-#define CONFIG_PANIC_HANG 	/* do not reset board on panic */
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
 
 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
 #define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
@@ -180,6 +181,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_BR3_PRELIM		0xf8100801	/* port size 8bit */
 #define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
 
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xf8100000	/* PIXIS registers */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
@@ -251,9 +253,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8544@0"
 #define OF_SOC			"soc8544@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -281,7 +280,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xe1000000
-#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCI1_IO_SIZE	0x00010000	/* 64k */
 
 /* PCI view of System Memory */
 #define CFG_PCI_MEMORY_BUS	0x00000000
@@ -293,27 +292,27 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
 #define CFG_PCIE2_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCIE2_IO_BASE	0x00000000
-#define CFG_PCIE2_IO_PHYS	0xe2000000
-#define CFG_PCIE2_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCIE2_IO_PHYS	0xe1010000
+#define CFG_PCIE2_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 1, Slot 2,tgtid 2, Base address a000 */
 #define CFG_PCIE1_MEM_BASE	0xa0000000
 #define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE	0x08000000	/* 128M */
-#define CFG_PCIE1_MEM_BASE2	0xa8000000
-#define CFG_PCIE1_MEM_PHYS2	CFG_PCIE1_MEM_BASE2
-#define CFG_PCIE1_MEM_SIZE2	0x04000000	/* 64M */
-#define CFG_PCIE1_IO_BASE	0x00000000	/* reuse mem LAW */
-#define CFG_PCIE1_IO_PHYS	0xaf000000
-#define CFG_PCIE1_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCIE1_IO_BASE	0x00000000
+#define CFG_PCIE1_IO_PHYS	0xe1020000
+#define CFG_PCIE1_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 3, direct to uli, tgtid 3, Base address b000 */
 #define CFG_PCIE3_MEM_BASE	0xb0000000
 #define CFG_PCIE3_MEM_PHYS	CFG_PCIE3_MEM_BASE
-#define CFG_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCIE3_MEM_SIZE	0x00100000	/* 1M */
 #define CFG_PCIE3_IO_BASE	0x00000000
-#define CFG_PCIE3_IO_PHYS	0xe3000000
+#define CFG_PCIE3_IO_PHYS	0xb0100000	/* reuse mem LAW */
 #define CFG_PCIE3_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCIE3_MEM_BASE2	0xb0200000
+#define CFG_PCIE3_MEM_PHYS2	CFG_PCIE3_MEM_BASE2
+#define CFG_PCIE3_MEM_SIZE2	0x00200000	/* 1M */
 
 #if defined(CONFIG_PCI)
 
@@ -344,7 +343,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SATA_ULI5288
 #define CFG_SCSI_MAX_SCSI_ID	4
 #define CFG_SCSI_MAX_LUN	1
-#define CFG_SCSI_MAX_DEVICE 	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAX_DEVICE	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
 #define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
 #endif /* SCSCI */
 
@@ -354,7 +353,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #if defined(CONFIG_TSEC_ENET)
 
 #ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 	1
+#define CONFIG_NET_MULTI	1
 #endif
 
 #define CONFIG_MII		1	/* MII PHY management */
@@ -363,18 +362,19 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_TSEC1_NAME	"eTSEC1"
 #define CONFIG_TSEC3	1
 #define CONFIG_TSEC3_NAME	"eTSEC3"
-#undef CONFIG_MPC85XX_FEC
 
 #define TSEC1_PHY_ADDR		0
 #define TSEC3_PHY_ADDR		1
 
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
 #define TSEC1_PHYIDX		0
 #define TSEC3_PHYIDX		0
 
 #define CONFIG_ETHPRIME		"eTSEC1"
 
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-
 #endif	/* CONFIG_TSEC_ENET */
 
 /*
@@ -392,7 +392,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
-
 /*
  * BOOTP options
  */
@@ -415,6 +414,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
     #define CONFIG_CMD_PCI
     #define CONFIG_CMD_BEDBUG
     #define CONFIG_CMD_NET
+    #define CONFIG_CMD_SCSI
+    #define CONFIG_CMD_EXT2
 #endif
 
 
@@ -441,10 +442,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux*/
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
 
 /* Cache Configuration */
-#define CFG_DCACHE_SIZE	32768
+#define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
 #if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
@@ -469,6 +470,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	00:E0:0C:02:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR	00:E0:0C:02:01:FD
@@ -482,7 +484,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_HOSTNAME	8544ds_unknown
 #define CONFIG_ROOTPATH	/nfs/mpc85xx
-#define CONFIG_BOOTFILE	8544ds_tmt/uImage.uboot
+#define CONFIG_BOOTFILE	8544ds/uImage.uboot
+#define CONFIG_UBOOTPATH	8544ds/u-boot.bin	/* TFTP server */
 
 #define CONFIG_SERVERIP	192.168.0.1
 #define CONFIG_GATEWAYIP 192.168.0.1
@@ -491,7 +494,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
 
 #define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
-#undef	CONFIG_BOOTARGS	/* the boot command will set bootargs*/
+#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs*/
 
 #define CONFIG_BAUDRATE	115200
 
@@ -499,10 +502,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PCIE_ENV \
  "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
 	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
- "pcie1regs=setenv a e000a; run pciereg\0"	\
- "pcie2regs=setenv a e0009; run pciereg\0"	\
- "pcie3regs=setenv a e000b; run pciereg\0"	\
- "pcieerr=md ${a}020 1; md ${a}e00;"		\
+ "pcieerr=md ${a}020 1; md ${a}e00 e;"		\
 	"pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"	\
 	"pci d.w $b.0 56 1;"			\
 	"pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \
@@ -511,12 +511,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 	"pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \
 	"pci w $b.0 130 ffffffff\0" \
  "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"	\
- "pcie1err=setenv a e000a; run pcieerr\0"	\
- "pcie2err=setenv a e0009; run pcieerr\0"	\
- "pcie3err=setenv a e000b; run pcieerr\0"	\
- "pcie1errc=setenv a e000a; run pcieerrc\0"	\
- "pcie2errc=setenv a e0009; run pcieerrc\0"	\
- "pcie3errc=setenv a e000b; run pcieerrc\0"
+ "pcie1regs=setenv a e000a; run pciereg\0"	\
+ "pcie2regs=setenv a e0009; run pciereg\0"	\
+ "pcie3regs=setenv a e000b; run pciereg\0"	\
+ "pcie1cfg=setenv b 3; run pciecfg\0" \
+ "pcie2cfg=setenv b 5; run pciecfg\0" \
+ "pcie3cfg=setenv b 0; run pciecfg\0" \
+ "pcie1err=setenv a e000a; setenv b 3; run pcieerr\0"	\
+ "pcie2err=setenv a e0009; setenv b 5; run pcieerr\0"	\
+ "pcie3err=setenv a e000b; setenv b 0; run pcieerr\0"	\
+ "pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0"	\
+ "pcie2errc=setenv a e0009; setenv b 5; run pcieerrc\0"	\
+ "pcie3errc=setenv a e000b; setenv b 0; run pcieerrc\0"
 #else
 #define	PCIE_ENV ""
 #endif
@@ -524,14 +530,14 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #if defined(CONFIG_PCI1)
 #define PCI_ENV \
  "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
-	"echo e;md ${a}e00 9\0" 		\
+	"echo e;md ${a}e00 9\0"			\
  "pci1regs=setenv a e0008; run pcireg\0"	\
  "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
 	"pci d.w $b.0 56 1\0"			\
- "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
-	"pci w.w $b.0 56 ffff\0"		\
- "pci1err=setenv a e0008; run pcierr\0"		\
- "pci1errc=setenv a e0008; run pcierrc\0"
+ "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \
+	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0"		\
+ "pci1err=setenv a e0008; setenv b 7; run pcierr\0"		\
+ "pci1errc=setenv a e0008; setenv b 7; run pcierrc\0"
 #else
 #define	PCI_ENV ""
 #endif
@@ -551,25 +557,39 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define ENET_ENV ""
 #endif
 
-#define	CONFIG_EXTRA_ENV_SETTINGS		\
- "netdev=eth0\0"				\
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+ "netdev=eth0\0"						\
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+ "tftpflash=tftpboot $loadaddr $uboot; "			\
+	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+	"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
  "consoledev=ttyS0\0"				\
  "ramdiskaddr=2000000\0"			\
- "ramdiskfile=8544ds_tmt/ramdisk.uboot\0"	\
- "fdtaddr=400000\0"				\
- "fdtfile=8544ds_tmt/mpc8544ds.dtb\0"		\
- "eoi=mw e00400b0 0\0" 				\
- "iack=md e00400a0 1\0" 			\
+ "ramdiskfile=8544ds/ramdisk.uboot\0"		\
+ "dtbaddr=c00000\0"				\
+ "dtbfile=8544ds/mpc8544ds.dtb\0"		\
+ "bdev=sda3\0"					\
+ "eoi=mw e00400b0 0\0"				\
+ "iack=md e00400a0 1\0"				\
  "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
 	"md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
- "ddrregs=setenv a e0002; run ddrreg\0" 	\
+ "ddrregs=setenv a e0002; run ddrreg\0"		\
  "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
-	"md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0" 	\
- "guregs=setenv a e00e0; run gureg\0" 		\
+	"md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0"	\
+ "guregs=setenv a e00e0; run gureg\0"		\
  "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
- "ecmregs=setenv a e0001; run ecmreg\0" 	\
- PCIE_ENV 	\
- PCI_ENV 	\
+ "ecmregs=setenv a e0001; run ecmreg\0"		\
+ "lawregs=md e0000c08 4b\0" \
+ "lbcregs=md e0005000 36\0" \
+ "dma0regs=md e0021100 12\0" \
+ "dma1regs=md e0021180 12\0" \
+ "dma2regs=md e0021200 12\0" \
+ "dma3regs=md e0021280 12\0" \
+ PCIE_ENV	\
+ PCI_ENV	\
  ENET_ENV
 
 
@@ -579,23 +599,23 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
  "console=$consoledev,$baudrate $othbootargs;"	\
  "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr - $fdtaddr"
+ "tftp $dtbaddr $dtbfile;"		\
+ "bootm $loadaddr - $dtbaddr"
 
 
-#define CONFIG_RAMBOOTCOMMAND 		\
+#define CONFIG_RAMBOOTCOMMAND		\
  "setenv bootargs root=/dev/ram rw "	\
  "console=$consoledev,$baudrate $othbootargs;"	\
  "tftp $ramdiskaddr $ramdiskfile;"	\
  "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
+ "tftp $dtbaddr $dtbfile;"		\
+ "bootm $loadaddr $ramdiskaddr $dtbaddr"
 
-#define CONFIG_BOOTCOMMAND 		\
- "setenv bootargs root=/dev/sda3 rw "	\
+#define CONFIG_BOOTCOMMAND		\
+ "setenv bootargs root=/dev/$bdev rw "	\
  "console=$consoledev,$baudrate $othbootargs;"	\
  "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr - $fdtaddr"
+ "tftp $dtbaddr $dtbfile;"		\
+ "bootm $loadaddr - $dtbaddr"
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 2e84fc8..6083715 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -11,7 +11,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -36,8 +36,14 @@
 #define CONFIG_MPC8548		1	/* MPC8548 specific */
 #define CONFIG_MPC8548CDS	1	/* MPC8548CDS board specific */
 
-#define CONFIG_PCI
-#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_PCI		/* enable any pci type devices */
+#define CONFIG_PCI1		/* PCI controller 1 */
+#define CONFIG_PCIE1		/* PCIE controler 1 (slot 1) */
+#undef CONFIG_RIO
+#undef CONFIG_PCI2
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
@@ -46,6 +52,7 @@
 #define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+#define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
 
 /*
@@ -65,16 +72,16 @@ extern unsigned long get_clock_freq(void);
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
-#define CONFIG_L2_CACHE		    	    /* toggle L2 cache 	*/
-#define CONFIG_BTB			    /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+#define CONFIG_CLEAR_LAW0		/* Clear LAW0 in cpu_init_r */
 
 /*
  * Only possible on E500 Version 2 or newer cores.
  */
 #define CONFIG_ENABLE_36BIT_PHYS	1
 
-
 #define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
 
 #undef	CFG_DRAM_TEST			/* memory test, takes time */
@@ -85,10 +92,14 @@ extern unsigned long get_clock_freq(void);
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
 #define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
+#define CFG_PCI1_ADDR	(CFG_CCSRBAR+0x8000)
+#define CFG_PCI2_ADDR	(CFG_CCSRBAR+0x9000)
+#define CFG_PCIE1_ADDR	(CFG_CCSRBAR+0xa000)
+
 /*
  * DDR Setup
  */
@@ -106,7 +117,6 @@ extern unsigned long get_clock_freq(void);
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -124,9 +134,9 @@ extern unsigned long get_clock_freq(void);
  *    Use GPCM = BRx[24:26] = 000
  *    Valid = BRx[31] = 1
  *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
- * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
+ * 0	4    8	  12   16   20	 24   28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001	 BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001	 BR1
  *
  * OR0, OR1:
  *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
@@ -137,11 +147,12 @@ extern unsigned long get_clock_freq(void);
  *    TRLX = use relaxed timing = ORx[29] = 1
  *    EAD = use external address latch delay = OR[31] = 1
  *
- * 0    4    8    12   16   20   24   28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
+ * 0	4    8	  12   16   20	 24   28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65	 ORx
  */
 
-#define CFG_FLASH_BASE		0xff000000	/* start of FLASH 8M */
+#define CFG_BOOT_BLOCK		0xff000000	/* boot TLB block */
+#define CFG_FLASH_BASE		CFG_BOOT_BLOCK	/* start of FLASH 16M */
 
 #define CFG_BR0_PRELIM		0xff801001
 #define CFG_BR1_PRELIM		0xff001001
@@ -156,7 +167,7 @@ extern unsigned long get_clock_freq(void);
 #define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 
-#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
 
 #define CFG_FLASH_CFI_DRIVER
 #define CFG_FLASH_CFI
@@ -166,7 +177,12 @@ extern unsigned long get_clock_freq(void);
 /*
  * SDRAM on the Local Bus
  */
-#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
+#define CFG_LBC_CACHE_BASE	0xf0000000	/* Localbus cacheable */
+#define CFG_LBC_CACHE_SIZE	64
+#define CFG_LBC_NONCACHE_BASE	0xf8000000	/* Localbus non-cacheable */
+#define CFG_LBC_NONCACHE_SIZE	64
+
+#define CFG_LBC_SDRAM_BASE	CFG_LBC_CACHE_BASE	/* Localbus SDRAM */
 #define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
 
 /*
@@ -180,14 +196,14 @@ extern unsigned long get_clock_freq(void);
  *    SDRAM for MSEL = BR2[24:26] = 011
  *    Valid = BR[31] = 1
  *
- * 0    4    8    12   16   20   24   28
+ * 0	4    8	  12   16   20	 24   28
  * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
  *
  * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
  * FIXME: the top 17 bits of BR2.
  */
 
-#define CFG_BR2_PRELIM          0xf0001861
+#define CFG_BR2_PRELIM		0xf0001861
 
 /*
  * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
@@ -196,19 +212,19 @@ extern unsigned long get_clock_freq(void);
  *    64MB mask for AM, OR2[0:7] = 1111 1100
  *		   XAM, OR2[17:18] = 11
  *    9 columns OR2[19-21] = 010
- *    13 rows   OR2[23-25] = 100
+ *    13 rows	OR2[23-25] = 100
  *    EAD set for extra time OR[31] = 1
  *
- * 0    4    8    12   16   20   24   28
+ * 0	4    8	  12   16   20	 24   28
  * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
  */
 
 #define CFG_OR2_PRELIM		0xfc006901
 
-#define CFG_LBC_LCRR		0x00030004    /* LB clock ratio reg */
-#define CFG_LBC_LBCR		0x00000000    /* LB config reg */
-#define CFG_LBC_LSRT		0x20000000  /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR		0x00000000  /* LB refresh timer prescal*/
+#define CFG_LBC_LCRR		0x00030004	/* LB clock ratio reg */
+#define CFG_LBC_LBCR		0x00000000	/* LB config reg */
+#define CFG_LBC_LSRT		0x20000000	/* LB sdram refresh timer */
+#define CFG_LBC_MRTPR		0x00000000	/* LB refresh timer prescal*/
 
 /*
  * LSDMR masks
@@ -236,7 +252,7 @@ extern unsigned long get_clock_freq(void);
 /*
  * Common settings for all Local Bus SDRAM commands.
  * At run time, either BSMA1516 (for CPU 1.1)
- *                  or BSMA1617 (for CPU 1.0) (old)
+ *		    or BSMA1617 (for CPU 1.0) (old)
  * is OR'ed in too.
  */
 #define CFG_LBC_LSDMR_COMMON	( CFG_LBC_LSDMR_RFCR16		\
@@ -256,61 +272,63 @@ extern unsigned long get_clock_freq(void);
  *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
  *    port-size = 8-bits  = BR[19:20] = 01
  *    no parity checking  = BR[21:22] = 00
- *    GPMC for MSEL       = BR[24:26] = 000
- *    Valid               = BR[31]    = 1
+ *    GPMC for MSEL	  = BR[24:26] = 000
+ *    Valid		  = BR[31]    = 1
  *
- * 0    4    8    12   16   20   24   28
+ * 0	4    8	  12   16   20	 24   28
  * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
  *
  * For OR3, need:
- *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
+ *    1 MB mask for AM,	  OR[0:16]  = 1111 1111 1111 0000 0
  *    disable buffer ctrl OR[19]    = 0
- *    CSNT                OR[20]    = 1
- *    ACS                 OR[21:22] = 11
- *    XACS                OR[23]    = 1
+ *    CSNT		  OR[20]    = 1
+ *    ACS		  OR[21:22] = 11
+ *    XACS		  OR[23]    = 1
  *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
- *    SETA                OR[28]    = 0
- *    TRLX                OR[29]    = 1
- *    EHTR                OR[30]    = 1
- *    EAD extra time      OR[31]    = 1
+ *    SETA		  OR[28]    = 0
+ *    TRLX		  OR[29]    = 1
+ *    EHTR		  OR[30]    = 1
+ *    EAD extra time	  OR[31]    = 1
  *
- * 0    4    8    12   16   20   24   28
+ * 0	4    8	  12   16   20	 24   28
  * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
  */
 
 #define CADMUS_BASE_ADDR 0xf8000000
-#define CFG_BR3_PRELIM   0xf8000801
-#define CFG_OR3_PRELIM   0xfff00ff7
+#define CFG_BR3_PRELIM	 0xf8000801
+#define CFG_OR3_PRELIM	 0xfff00ff7
 
 #define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_LOCK	1
 #define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
-#define CFG_INIT_RAM_END    	0x4000	    /* End of used area in RAM */
+#define CFG_INIT_RAM_END	0x4000		/* End of used area in RAM */
+
+#define CFG_INIT_L2_ADDR	0xf8f80000	/* relocate boot L2SRAM */
 
-#define CFG_GBL_DATA_SIZE  	128	    /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN	    	(256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN	    	(128 * 1024)	/* Reserved for malloc */
+#define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
 
 /* Serial Port */
-#define CONFIG_CONS_INDEX     2
+#define CONFIG_CONS_INDEX	2
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_NS16550
 #define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_REG_SIZE	1
 #define CFG_NS16550_CLK		get_bus_freq(0)
 
-#define CFG_BAUDRATE_TABLE  \
+#define CFG_BAUDRATE_TABLE \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
 
 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
-#ifdef  CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2 "> "
 #endif
 
@@ -318,9 +336,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8548@0"
 #define OF_SOC			"soc8548@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -331,55 +346,74 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_EEPROM_ADDR	0x57
 #define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
 #define CFG_I2C_OFFSET		0x3000
 
 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
+#define CFG_PCI_PHYS		0x80000000	/* 1G PCI TLB */
+
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xe2000000
-#define CFG_PCI1_IO_SIZE	0x00800000	/* 8M */
+#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
 
-#define CFG_PCI2_MEM_BASE	0x90000000
+#ifdef CONFIG_PCI2
+#define CFG_PCI2_MEM_BASE	0xa0000000
 #define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI2_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCI2_IO_BASE	0x00000000
 #define CFG_PCI2_IO_PHYS	0xe2800000
-#define CFG_PCI2_IO_SIZE	0x00800000	/* 8M */
+#define CFG_PCI2_IO_SIZE	0x00100000	/* 1M */
+#endif
 
-#define CFG_PEX_MEM_BASE	0xa0000000
-#define CFG_PEX_MEM_PHYS	CFG_PEX_MEM_BASE
-#define CFG_PEX_MEM_SIZE	0x20000000	/* 512M */
-#define CFG_PEX_IO_BASE		0x00000000
-#define CFG_PEX_IO_PHYS		0xe3000000
-#define CFG_PEX_IO_SIZE		0x01000000	/* 16M */
+#ifdef CONFIG_PCIE1
+#define CFG_PCIE1_MEM_BASE	0xa0000000
+#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCIE1_IO_BASE	0x00000000
+#define CFG_PCIE1_IO_PHYS	0xe3000000
+#define CFG_PCIE1_IO_SIZE	0x00100000	/*   1M */
+#endif
 
+#ifdef CONFIG_RIO
 /*
  * RapidIO MMU
  */
 #define CFG_RIO_MEM_BASE	0xC0000000
 #define CFG_RIO_MEM_SIZE	0x20000000	/* 512M */
+#endif
+
+#ifdef CONFIG_LEGACY
+#define BRIDGE_ID 17
+#define VIA_ID 2
+#else
+#define BRIDGE_ID 28
+#define VIA_ID 4
+#endif
 
 #if defined(CONFIG_PCI)
 
 #define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
-#define CONFIG_85XX_PCI2
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS	0x00000000
+#define CFG_PCI_MEMORY_PHYS	0x00000000
+#define CFG_PCI_MEMORY_SIZE	0x80000000
 
 #endif	/* CONFIG_PCI */
 
@@ -387,7 +421,7 @@ extern unsigned long get_clock_freq(void);
 #if defined(CONFIG_TSEC_ENET)
 
 #ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 	1
+#define CONFIG_NET_MULTI	1
 #endif
 
 #define CONFIG_MII		1	/* MII PHY management */
@@ -397,7 +431,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_TSEC2_NAME	"eTSEC1"
 #define CONFIG_TSEC3	1
 #define CONFIG_TSEC3_NAME	"eTSEC2"
-#undef CONFIG_TSEC4
+#define CONFIG_TSEC4
 #define CONFIG_TSEC4_NAME	"eTSEC3"
 #undef CONFIG_MPC85XX_FEC
 
@@ -410,10 +444,14 @@ extern unsigned long get_clock_freq(void);
 #define TSEC2_PHYIDX		0
 #define TSEC3_PHYIDX		0
 #define TSEC4_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 
 /* Options are: eTSEC[0-3] */
 #define CONFIG_ETHPRIME		"eTSEC0"
-
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #endif	/* CONFIG_TSEC_ENET */
 
 /*
@@ -473,7 +511,7 @@ extern unsigned long get_clock_freq(void);
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux*/
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
 
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE	32768
@@ -501,58 +539,154 @@ extern unsigned long get_clock_freq(void);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR	 00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
+#define CONFIG_ETH1ADDR	 00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#define CONFIG_ETH2ADDR	 00:E0:0C:00:02:FD
 #define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
+#define CONFIG_ETH3ADDR	 00:E0:0C:00:03:FD
 #endif
 
-#define CONFIG_IPADDR    192.168.1.253
+#define CONFIG_IPADDR	 192.168.1.253
 
-#define CONFIG_HOSTNAME  unknown
-#define CONFIG_ROOTPATH  /nfsroot
-#define CONFIG_BOOTFILE  your.uImage
+#define CONFIG_HOSTNAME	 unknown
+#define CONFIG_ROOTPATH	 /nfsroot
+#define CONFIG_BOOTFILE	8548cds/uImage.uboot
+#define CONFIG_UBOOTPATH	8548cds/u-boot.bin	/* TFTP server */
 
-#define CONFIG_SERVERIP  192.168.1.1
+#define CONFIG_SERVERIP	 192.168.1.1
 #define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK   255.255.255.0
+#define CONFIG_NETMASK	 255.255.255.0
 
-#define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
+#define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
 
-#define CONFIG_BOOTDELAY 10       /* -1 disables auto-boot */
-#undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs*/
 
 #define CONFIG_BAUDRATE	115200
 
-#define	CONFIG_EXTRA_ENV_SETTINGS				        \
-   "netdev=eth0\0"                                                      \
-   "consoledev=ttyS1\0"                                                 \
-   "ramdiskaddr=600000\0"                                               \
-   "ramdiskfile=your.ramdisk.u-boot\0"					\
-   "fdtaddr=400000\0"							\
-   "fdtfile=your.fdt.dtb\0"
+#if defined(CONFIG_PCIE1)
+#define PCIE_ENV \
+ "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
+	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
+ "pcieerr=md ${a}020 1; md ${a}e00 e; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
+	"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \
+	"pci d $b.0 130 1\0" \
+ "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;" \
+	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;"\
+	"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \
+ "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
+ "pcie1regs=setenv a e000a; run pciereg\0" \
+ "pcie1cfg=setenv b 3; run pciecfg\0" \
+ "pcie1err=setenv a e000a; setenv b 3; run pcieerr\0" \
+ "pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0"
+#else
+#define	PCIE_ENV ""
+#endif
+
+#if defined(CONFIG_PCI1) || defined(CONFIG_PCI2)
+#define PCI_ENV \
+ "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
+	"echo e;md ${a}e00 9\0" \
+ "pcierr=md ${a}e00 8; pci d.b $b.0 7 1;pci d.w $b.0 1e 1;" \
+	"pci d.w $b.0 56 1\0" \
+ "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \
+	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0"
+#else
+#define	PCI_ENV ""
+#endif
 
+#if defined(CONFIG_PCI1)
+#define PCI_ENV1 \
+ "pci1regs=setenv a e0008; run pcireg\0" \
+ "pci1err=setenv a e0008; setenv b 0; run pcierr\0" \
+ "pci1errc=setenv a e0008; setenv b 0; run pcierrc\0"
+#else
+#define	PCI_ENV1 ""
+#endif
 
-#define CONFIG_NFSBOOTCOMMAND	                                        \
-   "setenv bootargs root=/dev/nfs rw "                                  \
-      "nfsroot=$serverip:$rootpath "                                    \
+#if defined(CONFIG_PCI2)
+#define PCI_ENV2 \
+ "pci2regs=setenv a e0009; run pcireg\0" \
+ "pci2err=setenv a e0009; setenv b 123; run pcierr\0"	\
+ "pci2errc=setenv a e0009; setenv b 123; run pcierrc\0"
+#else
+#define	PCI_ENV2 ""
+#endif
+
+#if defined(CONFIG_TSEC_ENET)
+#define ENET_ENV \
+ "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
+	"md ${a}098 2\0" \
+ "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \
+ "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \
+ "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
+	"echo mib;md ${a}680 31\0" \
+ "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
+ "enet1regs=setenv a e0024; run enetreg\0" \
+ "enet2regs=setenv a e0025; run enetreg\0" \
+ "enet3regs=setenv a e0026; run enetreg\0" \
+ "enet4regs=setenv a e0027; run enetreg\0"
+#else
+#define ENET_ENV ""
+#endif
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+ "netdev=eth0\0"						\
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+ "tftpflash=tftpboot $loadaddr $uboot; "			\
+	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+	"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+ "consoledev=ttyS1\0"				\
+ "ramdiskaddr=2000000\0"			\
+ "ramdiskfile=ramdisk.uboot\0"			\
+ "fdtaddr=c00000\0"				\
+ "fdtfile=mpc8548cds.dtb\0"			\
+ "eoi=mw e00400b0 0\0"				\
+ "iack=md e00400a0 1\0"				\
+ "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
+	"md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
+ "ddrregs=setenv a e0002; run ddrreg\0"		\
+ "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
+	"md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0"	\
+ "guregs=setenv a e00e0; run gureg\0"		\
+ "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
+ "ecmregs=setenv a e0001; run ecmreg\0" \
+ "lawregs=md e0000c08 4b\0" \
+ "lbcregs=md e0005000 36\0" \
+ "dma0regs=md e0021100 12\0" \
+ "dma1regs=md e0021180 12\0" \
+ "dma2regs=md e0021200 12\0" \
+ "dma3regs=md e0021280 12\0" \
+ PCIE_ENV \
+ PCI_ENV \
+ PCI_ENV1 \
+ PCI_ENV2 \
+ ENET_ENV
+
+#define CONFIG_NFSBOOTCOMMAND						\
+   "setenv bootargs root=/dev/nfs rw "					\
+      "nfsroot=$serverip:$rootpath "					\
       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-      "console=$consoledev,$baudrate $othbootargs;"                     \
-   "tftp $loadaddr $bootfile;"                                          \
+      "console=$consoledev,$baudrate $othbootargs;"			\
+   "tftp $loadaddr $bootfile;"						\
    "tftp $fdtaddr $fdtfile;"						\
    "bootm $loadaddr - $fdtaddr"
 
 
 #define CONFIG_RAMBOOTCOMMAND \
-   "setenv bootargs root=/dev/ram rw "                                  \
-      "console=$consoledev,$baudrate $othbootargs;"                     \
-   "tftp $ramdiskaddr $ramdiskfile;"                                    \
-   "tftp $loadaddr $bootfile;"                                          \
-   "bootm $loadaddr $ramdiskaddr"
+   "setenv bootargs root=/dev/ram rw "					\
+      "console=$consoledev,$baudrate $othbootargs;"			\
+   "tftp $ramdiskaddr $ramdiskfile;"					\
+   "tftp $loadaddr $bootfile;"						\
+   "tftp $fdtaddr $fdtfile;"						\
+   "bootm $loadaddr $ramdiskaddr $fdtaddr"
 
-#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
+#define CONFIG_BOOTCOMMAND	CONFIG_NFSBOOTCOMMAND
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index a3025bd..1d1b7c9 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -312,9 +312,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8555@0"
 #define OF_SOC			"soc8555@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -350,6 +347,13 @@ extern unsigned long get_clock_freq(void);
 #define CFG_PCI2_IO_PHYS	0xe2100000
 #define CFG_PCI2_IO_SIZE	0x00100000	/* 1M */
 
+#ifdef CONFIG_LEGACY
+#define BRIDGE_ID 17
+#define VIA_ID 2
+#else
+#define BRIDGE_ID 28
+#define VIA_ID 4
+#endif
 
 #if defined(CONFIG_PCI)
 
@@ -377,13 +381,12 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
-#define FEC_PHY_ADDR		3
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
-#define FEC_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -475,6 +478,7 @@ extern unsigned long get_clock_freq(void);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index c10e551..a8f362f 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -292,9 +292,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8560@0"
 #define OF_SOC			"soc8560@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -360,11 +357,12 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -521,6 +519,7 @@
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index eef168c..ba744e9 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -28,20 +28,21 @@
 
 /* High Level Configuration Options */
 #define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500			1	/* BOOKE e500 family */
+#define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48/68 */
 #define CONFIG_MPC8568		1	/* MPC8568 specific */
 #define CONFIG_MPC8568MDS	1	/* MPC8568MDS board specific */
 
-#undef CONFIG_PCI
+#define CONFIG_PCI
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_QE			/* Enable QE */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
 /*#define CONFIG_DDR_2T_TIMING		 Sets the 2T timing bit */
 
 /*#define CONFIG_DDR_ECC*/			/* only for ECC DDR module */
-/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/	/* 	 DDR controller or DMA? */
+/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 
 
@@ -62,9 +63,9 @@ extern unsigned long get_clock_freq(void);
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
-/*#define CONFIG_L2_CACHE*/		    	    /* toggle L2 cache 	*/
-#define CONFIG_BTB						/* toggle branch predition */
-#define CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+#define CONFIG_L2_CACHE				/* toggle L2 cache 	*/
+#define CONFIG_BTB				/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING			/* toggle addr streaming   */
 
 /*
  * Only possible on E500 Version 2 or newer cores.
@@ -292,11 +293,9 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8568@0"
 #define OF_SOC			"soc8568@e0000000"
+#define OF_QE			"qe@e0080000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
 #define OF_STDOUT_PATH		"/soc8568@e0000000/serial@4600"
 
@@ -306,11 +305,14 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CFG_I2C_EEPROM_ADDR	0x57
+#define CFG_I2C_EEPROM_ADDR	0x52
 #define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+#define CFG_I2C_NOPROBES        {{0,0x69}}	/* Don't probe these addrs */
 #define CFG_I2C_OFFSET		0x3000
+#define CFG_I2C2_OFFSET		0x3100
 
 /*
  * General PCI
@@ -318,7 +320,7 @@ extern unsigned long get_clock_freq(void);
  */
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xe2000000
 #define CFG_PCI1_IO_SIZE	0x00800000	/* 8M */
@@ -337,6 +339,44 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
 
+#ifdef CONFIG_QE
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#ifndef CONFIG_TSEC_ENET
+#define CONFIG_ETHPRIME         "FSL UEC0"
+#endif
+#define CONFIG_PHY_MODE_NEED_CHANGE
+#define CONFIG_eTSEC_MDIO_BUS
+
+#ifdef CONFIG_eTSEC_MDIO_BUS
+#define CONFIG_MIIM_ADDRESS 	0xE0024520
+#endif
+
+#define CONFIG_UEC_ETH1         /* GETH1 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM        0       /* UCC1 */
+#define CFG_UEC1_RX_CLK         QE_CLK_NONE
+#define CFG_UEC1_TX_CLK         QE_CLK16
+#define CFG_UEC1_ETH_TYPE       GIGA_ETH
+#define CFG_UEC1_PHY_ADDR       7
+#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+#define CONFIG_UEC_ETH2         /* GETH2 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM        1       /* UCC2 */
+#define CFG_UEC2_RX_CLK         QE_CLK_NONE
+#define CFG_UEC2_TX_CLK         QE_CLK16
+#define CFG_UEC2_ETH_TYPE       GIGA_ETH
+#define CFG_UEC2_PHY_ADDR       1
+#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
+#endif
+#endif /* CONFIG_QE */
+
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -345,21 +385,17 @@ extern unsigned long get_clock_freq(void);
 
 #endif	/* CONFIG_PCI */
 
-
-#if defined(CONFIG_TSEC_ENET)
-
 #ifndef CONFIG_NET_MULTI
 #define CONFIG_NET_MULTI 	1
 #endif
 
+#if defined(CONFIG_TSEC_ENET)
+
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_TSEC1	1
 #define CONFIG_TSEC1_NAME	"eTSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"eTSEC1"
-#undef  CONFIG_TSEC3
-#undef  CONFIG_TSEC4
-#undef  CONFIG_MPC85XX_FEC
 
 #define TSEC1_PHY_ADDR		2
 #define TSEC2_PHY_ADDR		3
@@ -367,7 +403,10 @@ extern unsigned long get_clock_freq(void);
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 
-/* Options are: eTSEC[0-3] */
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+
+/* Options are: eTSEC[0-1] */
 #define CONFIG_ETHPRIME		"eTSEC0"
 
 #endif	/* CONFIG_TSEC_ENET */
@@ -457,12 +496,15 @@ extern unsigned long get_clock_freq(void);
  */
 
 /* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
 #define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif
 
 #define CONFIG_IPADDR    192.168.1.253
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 64dcbd0..7d8a380 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -185,6 +185,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
 
 
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xf8100000      /* PIXIS registers */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
@@ -268,9 +269,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU		"PowerPC,8641@0"
 #define OF_SOC		"soc8641@f8000000"
 #define OF_TBCLK	(bd->bi_busfreq / 4)
@@ -417,6 +415,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define TSEC2_PHYIDX		0
 #define TSEC3_PHYIDX		0
 #define TSEC4_PHYIDX		0
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 
 #define CONFIG_ETHPRIME		"eTSEC1"
 
@@ -604,6 +606,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif
 
+#define CONFIG_HAS_ETH0		1
 #define CONFIG_HAS_ETH1		1
 #define CONFIG_HAS_ETH2		1
 #define CONFIG_HAS_ETH3		1
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 5470373..652210c 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -96,7 +96,6 @@
 #define CONFIG_SUPPORT_VFAT
 
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
-#define CONFIG_AUTO_UPDATE_SHOW 1       /* use board show routine       */
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -168,38 +167,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
 
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -276,11 +255,6 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
-#endif
-
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
@@ -306,9 +280,6 @@
 #define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 
-#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
-#define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
-
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
@@ -317,7 +288,7 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
-#if 1 /* test-only */
+
 /* CAT24WC08/16... */
 #define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
@@ -325,15 +296,6 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
 					/* last 4 bits of the address	*/
-#else
-/* CAT24WC32/64... */
-#define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
-#define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
-					/* 32 byte page write mode using*/
-					/* last 5 bits of the address	*/
-#endif
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index dbf9422..a6a1e73 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -270,15 +270,19 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 #define CONFIG_MPC85XX_FEC	1
 #define CONFIG_MPC85XX_FEC_NAME		"FEC"
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
+#define FEC_FLAGS		0
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
 
+#define CONFIG_HAS_ETH0
 #define	CONFIG_HAS_ETH1		1
 #define	CONFIG_HAS_ETH2		1
 
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
index 6bdfa5d..9a17e3d 100644
--- a/include/configs/PM856.h
+++ b/include/configs/PM856.h
@@ -262,11 +262,12 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 #endif  /* CONFIG_TSEC_ENET */
 
@@ -391,6 +392,7 @@
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:40:42:01:00:00
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:40:42:01:00:01
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
index dd1decd..8a74c4f 100644
--- a/include/configs/PPChameleonEVB.h
+++ b/include/configs/PPChameleonEVB.h
@@ -429,6 +429,8 @@
 #define CFG_ENV_ADDR_REDUND	0xFFFFA000
 #define CFG_ENV_SIZE_REDUND	0x2000
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 #endif	/* ENVIRONMENT_IN_EEPROM */
 
 
diff --git a/include/configs/R360MPI.h b/include/configs/R360MPI.h
index 516ec64..a98b4af 100644
--- a/include/configs/R360MPI.h
+++ b/include/configs/R360MPI.h
@@ -233,6 +233,7 @@
 #define	CFG_ENV_OFFSET		0x40000	/* Offset of Environment		*/
 #define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment sector	*/
 #define	CFG_ENV_SIZE		0x4000	/* Used Size of Environment sector	*/
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
diff --git a/include/configs/RRvision.h b/include/configs/RRvision.h
index 1e6e8c0..32e2285 100644
--- a/include/configs/RRvision.h
+++ b/include/configs/RRvision.h
@@ -235,6 +235,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h
index 2b2ae01..dccdf0c 100644
--- a/include/configs/TASREG.h
+++ b/include/configs/TASREG.h
@@ -43,6 +43,10 @@
 
 #define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
 
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 8360d8c..e0c9d81 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -131,8 +131,9 @@
 /* USB */
 #if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
 #define CONFIG_USB_OHCI_NEW
-#define ADD_USB_CMD		CFG_CMD_USB | CFG_CMD_FAT
 #define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_USB
 
 #undef CFG_USB_OHCI_BOARD_INIT
 #define CFG_USB_OHCI_CPU_INIT
@@ -140,8 +141,6 @@
 #define CFG_USB_OHCI_SLOT_NAME	"mpc5200"
 #define CFG_USB_OHCI_MAX_ROOT_PORTS	15
 
-#else
-#define ADD_USB_CMD		0
 #endif
 
 #ifndef CONFIG_CAM5200
@@ -702,11 +701,9 @@
  * Open firmware flat tree support
  *-----------------------------------------------------------------------
  */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
index 2bdcf2c..7a38010 100644
--- a/include/configs/TQM823L.h
+++ b/include/configs/TQM823L.h
@@ -70,8 +70,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM823L/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -205,6 +206,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h
index 58bc5d3..e8b6a80 100644
--- a/include/configs/TQM823M.h
+++ b/include/configs/TQM823M.h
@@ -70,8 +70,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM823M/uImage\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
+	"fdt_addr=40080000\0"						\
+	"kernel_addr=400A0000\0"					\
+	"ramdisk_addr=40280000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -202,6 +203,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index c3efb7b..0147252 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -28,9 +28,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define DEBUG
-#undef DEBUG
-
 /*
  * High Level Configuration Options
  */
@@ -256,6 +253,8 @@ extern int tqm834x_num_flash_banks;
 #define TSEC2_PHY_ADDR			1
 #define TSEC1_PHYIDX			0
 #define TSEC2_PHYIDX			0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME			"TSEC0"
@@ -502,6 +501,7 @@ extern int tqm834x_num_flash_banks;
  */
 
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR		D2:DA:5E:44:BC:29
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		1E:F3:40:21:92:53
diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h
index 74b16c7..beeca63 100644
--- a/include/configs/TQM850L.h
+++ b/include/configs/TQM850L.h
@@ -66,8 +66,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM850L/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -192,6 +193,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h
index e3936c3..d5609c1 100644
--- a/include/configs/TQM850M.h
+++ b/include/configs/TQM850M.h
@@ -64,8 +64,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM850M/uImage\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
+	"fdt_addr=40080000\0"						\
+	"kernel_addr=400A0000\0"					\
+	"ramdisk_addr=40280000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -191,6 +192,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h
index ae22b77..e35b5b2 100644
--- a/include/configs/TQM855L.h
+++ b/include/configs/TQM855L.h
@@ -69,8 +69,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM855L/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -196,6 +197,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index 5d54f87..cd5212e 100644
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -69,8 +69,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM855M/uImage\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
+	"fdt_addr=40080000\0"						\
+	"kernel_addr=400A0000\0"					\
+	"ramdisk_addr=40280000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -231,6 +232,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index d5ce3ba..2f23c50 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -94,7 +94,6 @@
  */
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
-#define CONFIG_ADD_RAM_INFO	1		/* print additional info*/
 
 #if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560)
 /* TQM8540 & 8560 need DLL-override */
@@ -266,8 +265,12 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
+#define FEC_FLAGS		0
+#define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
 
diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h
index 40c0940..d5838db 100644
--- a/include/configs/TQM860L.h
+++ b/include/configs/TQM860L.h
@@ -69,8 +69,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM860L/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -199,6 +200,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
index 481e3d0..684b86f 100644
--- a/include/configs/TQM860M.h
+++ b/include/configs/TQM860M.h
@@ -69,8 +69,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM860M/uImage\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
+	"fdt_addr=40080000\0"						\
+	"kernel_addr=400A0000\0"					\
+	"ramdisk_addr=40280000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -198,6 +199,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
index bb3b1cc..f09d3d1 100644
--- a/include/configs/TQM862L.h
+++ b/include/configs/TQM862L.h
@@ -72,8 +72,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM862L/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
+	"fdt_addr=40040000\0"						\
+	"kernel_addr=40060000\0"					\
+	"ramdisk_addr=40200000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -200,6 +201,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h
index d687d08..039aa3a 100644
--- a/include/configs/TQM862M.h
+++ b/include/configs/TQM862M.h
@@ -72,8 +72,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM862M/uImage\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
+	"fdt_addr=40080000\0"						\
+	"kernel_addr=400A0000\0"					\
+	"ramdisk_addr=40280000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -201,6 +202,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index ff00c13..0d77891 100644
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -81,8 +81,9 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"bootfile=/tftpboot/TQM866M/uImage\0"				\
-	"kernel_addr=40080000\0"					\
-	"ramdisk_addr=40180000\0"					\
+	"fdt_addr=40080000\0"						\
+	"kernel_addr=400A0000\0"					\
+	"ramdisk_addr=40280000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -241,6 +242,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h
index 34f0ebd..14848ab 100644
--- a/include/configs/VOH405.h
+++ b/include/configs/VOH405.h
@@ -153,38 +153,18 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h
index c1b3da8..656784a 100644
--- a/include/configs/WUH405.h
+++ b/include/configs/WUH405.h
@@ -145,38 +145,16 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h
index 89564a9..22eac1b 100644
--- a/include/configs/ads5121.h
+++ b/include/configs/ads5121.h
@@ -241,7 +241,6 @@
 #define CONFIG_NET_MULTI
 #define CONFIG_PHY_ADDR		0x1
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_ETHADDR		00:e0:5e:00:e5:14
 
 #if 0
 /*
@@ -267,22 +266,20 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
 #if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_PCI		\
-				| CFG_CMD_NET		\
-				| CFG_CMD_PING		\
-				)
-#else
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_NET		\
-				| CFG_CMD_PING		\
-	  			| CFG_CMD_MII		\
-				| CFG_CMD_I2C)
+#define CONFIG_CMD_PCI
 #endif
 
-#include <cmd_confdefs.h>
-
 /*
  * Watchdog timeout = CFG_WATCHDOG_VALUE * 65536 / IPS clock.
  * For example, when IPS is set to 66MHz and CFG_WATCHDOG_VALUE is set
@@ -299,7 +296,7 @@
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#ifdef CONFIG_CMD_KGDB
 	#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 	#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -321,7 +318,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#ifdef CONFIG_CMD_KGDB
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -337,7 +334,7 @@
 #define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02	/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#ifdef CONFIG_CMD_KGDB
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
@@ -348,18 +345,11 @@
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_HOSTNAME		ads5121
-#define CONFIG_ROOTPATH		/nfsroot/rootfs
 #define CONFIG_BOOTFILE		uImage
 
-#define CONFIG_IPADDR		192.168.160.77
-#define CONFIG_SERVERIP		192.168.1.1
-#define CONFIG_GATEWAYIP	192.168.1.1
-#define CONFIG_NETMASK		255.255.0.0
-
 #define CONFIG_LOADADDR		200000	/* default location for tftp and bootm */
 
-//#define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
-#define CONFIG_BOOTDELAY	-1
+#define CONFIG_BOOTDELAY	5	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS			/* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE		115200
@@ -383,9 +373,9 @@
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
 		"bootm\0"						\
-	"load=tftp 100000 /tftpboot/ads5121/u-boot.bin\0"		\
-	"update=protect off fff00000 fff3ffff; "			\
-		"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
+	"load=tftp 200000 /tftpboot/ads5121/u-boot.bin\0"		\
+	"update=protect off FFF00000 +${filesize};"			\
+		"era FFF00000 +${filesize};cp.b 200000 FFF00000 ${filesize}\0" \
 	"upd=run load;run update\0"					\
 	""
 
diff --git a/include/configs/at91rm9200dk.h b/include/configs/at91rm9200dk.h
index ecfa21d..a65c5f3 100644
--- a/include/configs/at91rm9200dk.h
+++ b/include/configs/at91rm9200dk.h
@@ -163,6 +163,11 @@
 #define CONFIG_NET_RETRY_COUNT		20
 #define CONFIG_AT91C_USE_RMII
 
+/* AC Characteristics */
+/* DLYBS = tCSS = 250ns min and DLYBCT = tCSH = 250ns */
+#define DATAFLASH_TCSS	(0xC << 16)
+#define DATAFLASH_TCHS	(0x1 << 24)
+
 #define CONFIG_HAS_DATAFLASH		1
 #define CFG_SPI_WRITE_TOUT		(5*CFG_HZ)
 #define CFG_MAX_DATAFLASH_BANKS 	2
diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h
index e1d8f74..75b153e 100644
--- a/include/configs/atstk1002.h
+++ b/include/configs/atstk1002.h
@@ -183,10 +183,9 @@
 #define CFG_LONGHELP			1
 
 #define CFG_MEMTEST_START						\
-	({ DECLARE_GLOBAL_DATA_PTR; gd->bd->bi_dram[0].start; })
+	({ gd->bd->bi_dram[0].start; })
 #define CFG_MEMTEST_END							\
 	({								\
-		DECLARE_GLOBAL_DATA_PTR;				\
 		gd->bd->bi_dram[0].start + gd->bd->bi_dram[0].size;	\
 	})
 #define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 19b29aa..14c5638 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -222,6 +222,8 @@
 #define CFG_SIMULATE_SPD_EEPROM	0xff	/* simulate spd eeprom on this address	*/
 #define SPD_EEPROM_ADDRESS	{CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51}
 #define CFG_MBYTES_SDRAM	(64)	/* 64MB fixed size for early-sdram-init */
+#define CONFIG_PROG_SDRAM_TLB
+#undef  CFG_DRAM_TEST
 
 /*-----------------------------------------------------------------------
  * I2C
diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h
index 7662856..d554348 100644
--- a/include/configs/cm5200.h
+++ b/include/configs/cm5200.h
@@ -31,31 +31,25 @@
 #define CONFIG_MPC5200		1	/* (more precisely an MPC5200 CPU) */
 #define CONFIG_CM5200		1	/* ... on CM5200 platform */
 
-
 /*
  * Supported commands
  */
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_ASKENV	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_ECHO	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_FLASH	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_DIAG	| \
-				CFG_CMD_REGINFO | \
-				CFG_CMD_SNTP	| \
-				CFG_CMD_BSP	| \
-				CFG_CMD_USB	| \
-				CFG_CMD_FAT	| \
-				CFG_CMD_JFFS2)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
 
 /*
  * Serial console configuration
@@ -65,7 +59,6 @@
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 #define CONFIG_SILENT_CONSOLE	1	/* needed to silence i2c_init() */
 
-
 /*
  * Ethernet configuration
  */
@@ -76,7 +69,6 @@
 #define CONFIG_MISC_INIT_R	1
 #define CONFIG_MAC_OFFSET	0x35	/* MAC address offset in I2C EEPROM */
 
-
 /*
  * POST support
  */
@@ -85,11 +77,9 @@
 /* List of I2C addresses to be verified by POST */
 #define I2C_ADDR_LIST		{ CFG_I2C_SLAVE, CFG_I2C_IO, CFG_I2C_EEPROM }
 
-
 /* display image timestamps */
 #define CONFIG_TIMESTAMP	1
 
-
 /*
  * Autobooting
  */
@@ -142,19 +132,16 @@
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_flash"
 
-
 /*
  * Low level configuration
  */
 
-
 /*
  * Clock configuration
  */
 #define CFG_MPC5XXX_CLKIN	33000000	/* SYS_XTAL_IN = 33MHz */
 #define CFG_IPBCLK_EQUALS_XLBCLK	1	/* IPB = 133MHz */
 
-
 /*
  * Memory map
  */
@@ -189,7 +176,7 @@
  */
 #define CFG_FLASH_CFI		1
 #define CFG_FLASH_CFI_DRIVER	1
-#define CFG_FLASH_BASE		0xfc000000	
+#define CFG_FLASH_BASE		0xfc000000
 /* we need these despite using CFI */
 #define CFG_MAX_FLASH_BANKS	1	/* max num of flash banks */
 #define CFG_MAX_FLASH_SECT	256	/* max num of sectors on one chip */
@@ -220,7 +207,6 @@
 #define CFG_CS_BURST		0x00000000
 #define CFG_CS_DEADCYCLE	0x00000001
 
-
 /*
  * SDRAM configuration
  * settings for k4s561632E-xx75, assuming XLB = 132 MHz
@@ -230,8 +216,6 @@
 #define SDRAM_CONFIG1	0xE2333900
 #define SDRAM_CONFIG2	0x8EE70000
 
-
-
 /*
  * MTD configuration
  */
@@ -243,7 +227,6 @@
 					"2m(kernel),27904k(rootfs),"	\
 					"-(config)"
 
-
 /*
  * I2C configuration
  */
@@ -254,13 +237,11 @@
 #define CFG_I2C_IO		0x38	/* PCA9554AD I2C I/O port address */
 #define CFG_I2C_EEPROM		0x53	/* I2C EEPROM device address */
 
-
 /*
  * RTC configuration
  */
 #define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
 
-
 /*
  * USB configuration
  */
@@ -289,7 +270,6 @@
 #define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
-
 /*
  * Pin multiplexing configuration
  */
@@ -307,7 +287,6 @@
  */
 #define CFG_GPS_PORT_CONFIG	0x10559C44
 
-
 /*
  * Miscellaneous configurable options
  */
@@ -327,7 +306,6 @@
 #define CFG_LOAD_ADDR		0x100000	/* default load address */
 #define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
 
-
 /*
  * Various low-level settings
  */
@@ -339,16 +317,14 @@
 
 #define CFG_XLB_PIPELINING	1	/* enable transaction pipeling */
 
-
 /*
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#ifdef CONFIG_CMD_KGDB
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
-
 /*
  * Flat Device Tree support
  */
diff --git a/include/configs/cmi_mpc5xx.h b/include/configs/cmi_mpc5xx.h
index cd92af2..a869364 100644
--- a/include/configs/cmi_mpc5xx.h
+++ b/include/configs/cmi_mpc5xx.h
@@ -59,6 +59,8 @@
  */
 #include <config_cmd_default.h>
 
+#undef	CONFIG_CMD_NET		/* disabeled - causes compile errors */
+
 #define CONFIG_CMD_MEMORY
 #define CONFIG_CMD_LOADB
 #define CONFIG_CMD_REGINFO
@@ -169,8 +171,9 @@
 #define	CFG_ENV_IS_IN_FLASH	1
 
 #ifdef	CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_OFFSET		0x00020000		/* Environment starts at this adress 	*/
-#define	CFG_ENV_SIZE		0x00010000		/* Set whole sector as env 		*/
+#define CFG_ENV_OFFSET		0x00020000	/* Environment starts at this adress 	*/
+#define	CFG_ENV_SIZE		0x00010000	/* Set whole sector as env 		*/
+#define	CFG_USE_PPCENV				/* Environment embedded in sect .ppcenv */
 #endif
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h
index 510524a..104d94e 100644
--- a/include/configs/cobra5272.h
+++ b/include/configs/cobra5272.h
@@ -65,8 +65,10 @@
  * Enable use of Ethernet
  * ---
  */
+#define CONFIG_MCFFEC
 
-#define FEC_ENET
+/* Enable Dma Timer */
+#define CONFIG_MCFTMR
 
 /* ---
  * Define baudrate for UART1 (console output, tftp, ...)
@@ -76,6 +78,8 @@
  * ---
  */
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
@@ -151,6 +155,26 @@
 #undef CONFIG_CMD_LOADB
 #undef CONFIG_CMD_MII
 
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 /*
  *-----------------------------------------------------------------------------
diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h
new file mode 100644
index 0000000..8ecd059
--- /dev/null
+++ b/include/configs/davinci_dvevm.h
@@ -0,0 +1,214 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * Define this to make U-Boot skip low level initialization when loaded
+ * by initial bootloader. Not required by NAND U-Boot version but IS
+ * required for a NOR version used to burn the real NOR U-Boot into
+ * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
+ * so it is NOT possible to build a U-Boot with both NAND and NOR routines.
+ * NOR U-Boot is loaded directly from Flash so it must perform all the
+ * low level initialization itself. NAND version is loaded by an initial
+ * bootloader (UBL in TI-ese) that performs such an initialization so it's
+ * skipped in NAND version. The third DaVinci boot mode loads a bootloader
+ * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
+ * performing low level init prior to loading. All that means we can NOT use
+ * NAND version to put U-Boot into NOR because it doesn't have NOR support and
+ * we can NOT use NOR version because it performs low level initialization
+ * effectively destroying itself in DDR memory. That's why a separate NOR
+ * version with this define is needed. It is loaded via UART, then one uses
+ * it to somehow download a proper NOR version built WITHOUT this define to
+ * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
+ * NOR support into the initial bootloader so it won't be needed but DaVinci
+ * static RAM might be too small for this (I have something like 2Kbytes left
+ * as of now, without NOR support) so this might've not happened...
+ *
+#define CONFIG_NOR_UART_BOOT
+ */
+
+/*=======*/
+/* Board */
+/*=======*/
+#define DV_EVM
+#define CFG_NAND_SMALLPAGE
+#define CFG_USE_NOR
+/*===================*/
+/* SoC Configuration */
+/*===================*/
+#define CONFIG_ARM926EJS			/* arm926ejs CPU core */
+#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
+#define CFG_TIMERBASE		0x01c21400	/* use timer 0 */
+#define CFG_HZ_CLOCK		27000000	/* Timer Input clock freq */
+#define CFG_HZ			1000
+/*====================================================*/
+/* EEPROM definitions for Atmel 24C256BN SEEPROM chip */
+/* on Sonata/DV_EVM board. No EEPROM on schmoogie.    */
+/*====================================================*/
+#define CFG_I2C_EEPROM_ADDR_LEN		2
+#define CFG_I2C_EEPROM_ADDR		0x50
+#define CFG_EEPROM_PAGE_WRITE_BITS	6
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	20
+/*=============*/
+/* Memory Info */
+/*=============*/
+#define CFG_MALLOC_LEN		(0x10000 + 128*1024)	/* malloc() len */
+#define CFG_GBL_DATA_SIZE	128		/* reserved for initial data */
+#define CFG_MEMTEST_START	0x80000000	/* memtest start address */
+#define CFG_MEMTEST_END		0x81000000	/* 16MB RAM test */
+#define CONFIG_NR_DRAM_BANKS	1		/* we have 1 bank of DRAM */
+#define CONFIG_STACKSIZE	(256*1024)	/* regular stack */
+#define PHYS_SDRAM_1		0x80000000	/* DDR Start */
+#define PHYS_SDRAM_1_SIZE	0x10000000	/* DDR size 256MB */
+#define DDR_8BANKS				/* 8-bank DDR2 (256MB) */
+/*====================*/
+/* Serial Driver info */
+/*====================*/
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	4		/* NS16550 register size */
+#define CFG_NS16550_COM1	0x01c20000	/* Base address of UART0 */
+#define CFG_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_CONS_INDEX	1		/* use UART0 for console */
+#define CONFIG_BAUDRATE		115200		/* Default baud rate */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+/*===================*/
+/* I2C Configuration */
+/*===================*/
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_DAVINCI_I2C
+#define CFG_I2C_SPEED		80000	/* 100Kbps won't work, silicon bug */
+#define CFG_I2C_SLAVE		10	/* Bogus, master-only in U-Boot */
+/*==================================*/
+/* Network & Ethernet Configuration */
+/*==================================*/
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT	10
+/*=====================*/
+/* Flash & Environment */
+/*=====================*/
+#ifdef CFG_USE_NAND
+#undef CFG_ENV_IS_IN_FLASH
+#define CFG_NO_FLASH
+#define CFG_ENV_IS_IN_NAND		/* U-Boot env in NAND Flash  */
+#ifdef CFG_NAND_SMALLPAGE
+#define CFG_ENV_SECT_SIZE	512	/* Env sector Size */
+#define CFG_ENV_SIZE		SZ_16K
+#else
+#define CFG_ENV_SECT_SIZE	2048	/* Env sector Size */
+#define CFG_ENV_SIZE		SZ_128K
+#endif
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
+#define CONFIG_SKIP_RELOCATE_UBOOT	/* to a proper address, init done */
+#define CFG_NAND_BASE		0x02000000
+#define CFG_NAND_HW_ECC
+#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
+#define NAND_MAX_CHIPS		1
+#define CFG_ENV_OFFSET		0x0	/* Block 0--not used by bootcode */
+#define DEF_BOOTM		""
+#elif defined(CFG_USE_NOR)
+#ifdef CONFIG_NOR_UART_BOOT
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
+#define CONFIG_SKIP_RELOCATE_UBOOT	/* to a proper address, init done */
+#else
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#endif
+#define CFG_ENV_IS_IN_FLASH
+#undef CFG_NO_FLASH
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_MAX_FLASH_BANKS	1		/* max number of flash banks */
+#define CFG_FLASH_SECT_SZ	0x10000		/* 64KB sect size AMD Flash */
+#define CFG_ENV_OFFSET		(CFG_FLASH_SECT_SZ*3)
+#define PHYS_FLASH_1		0x02000000	/* CS2 Base address 	 */
+#define CFG_FLASH_BASE		PHYS_FLASH_1	/* Flash Base for U-Boot */
+#define PHYS_FLASH_SIZE		0x2000000	/* Flash size 32MB 	 */
+#define CFG_MAX_FLASH_SECT	(PHYS_FLASH_SIZE/CFG_FLASH_SECT_SZ)
+#define CFG_ENV_SECT_SIZE	CFG_FLASH_SECT_SZ	/* Env sector Size */
+#endif
+/*==============================*/
+/* U-Boot general configuration */
+/*==============================*/
+#undef 	CONFIG_USE_IRQ			/* No IRQ/FIQ in U-Boot */
+#define CONFIG_MISC_INIT_R
+#undef CONFIG_BOOTDELAY
+#define CONFIG_BOOTFILE		"uImage"	/* Boot file name */
+#define CFG_PROMPT		"U-Boot > "	/* Monitor Command Prompt */
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size  */
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print buffer sz */
+#define CFG_MAXARGS		16		/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR		0x80700000	/* default Linux kernel load address */
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE		/* Won't work with hush so far, may be later */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+#define CONFIG_CMDLINE_EDITING
+#define CFG_LONGHELP
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+/*===================*/
+/* Linux Information */
+/*===================*/
+#define LINUX_BOOT_PARAM_ADDR	0x80000100
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTARGS		"mem=120M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
+#define CONFIG_BOOTCOMMAND	"setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2050000"
+/*=================*/
+/* U-Boot commands */
+/*=================*/
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_EEPROM
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#ifdef CFG_USE_NAND
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_NAND
+#elif defined(CFG_USE_NOR)
+#define CONFIG_CMD_JFFS2
+#else
+#error "Either CFG_USE_NAND or CFG_USE_NOR _MUST_ be defined !!!"
+#endif
+/*=======================*/
+/* KGDB support (if any) */
+/*=======================*/
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
diff --git a/include/configs/davinci_schmoogie.h b/include/configs/davinci_schmoogie.h
new file mode 100644
index 0000000..96c9a30
--- /dev/null
+++ b/include/configs/davinci_schmoogie.h
@@ -0,0 +1,157 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*=======*/
+/* Board */
+/*=======*/
+#define SCHMOOGIE
+#define CFG_NAND_LARGEPAGE
+#define CFG_USE_NAND
+/*===================*/
+/* SoC Configuration */
+/*===================*/
+#define CONFIG_ARM926EJS			/* arm926ejs CPU core */
+#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
+#define CFG_TIMERBASE		0x01c21400	/* use timer 0 */
+#define CFG_HZ_CLOCK		27000000	/* Timer Input clock freq */
+#define CFG_HZ			1000
+/*=============*/
+/* Memory Info */
+/*=============*/
+#define CFG_MALLOC_LEN		(0x10000 + 256*1024)	/* malloc() len */
+#define CFG_GBL_DATA_SIZE	128		/* reserved for initial data */
+#define CFG_MEMTEST_START	0x80000000	/* memtest start address */
+#define CFG_MEMTEST_END		0x81000000	/* 16MB RAM test */
+#define CONFIG_NR_DRAM_BANKS	1		/* we have 1 bank of DRAM */
+#define CONFIG_STACKSIZE	(256*1024)	/* regular stack */
+#define PHYS_SDRAM_1		0x80000000	/* DDR Start */
+#define PHYS_SDRAM_1_SIZE	0x08000000	/* DDR size 128MB */
+#define DDR_4BANKS				/* 4-bank DDR2 (128MB) */
+/*====================*/
+/* Serial Driver info */
+/*====================*/
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	4		/* NS16550 register size */
+#define CFG_NS16550_COM1	0x01c20000	/* Base address of UART0 */
+#define CFG_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_CONS_INDEX	1		/* use UART0 for console */
+#define CONFIG_BAUDRATE		115200		/* Default baud rate */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+/*===================*/
+/* I2C Configuration */
+/*===================*/
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_DAVINCI_I2C
+#define CFG_I2C_SPEED		80000	/* 100Kbps won't work, silicon bug */
+#define CFG_I2C_SLAVE		10	/* Bogus, master-only in U-Boot */
+/*==================================*/
+/* Network & Ethernet Configuration */
+/*==================================*/
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT	10
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+/*=====================*/
+/* Flash & Environment */
+/*=====================*/
+#undef CFG_ENV_IS_IN_FLASH
+#define CFG_NO_FLASH
+#define CFG_ENV_IS_IN_NAND		/* U-Boot env in NAND Flash  */
+#define CFG_ENV_SECT_SIZE	2048	/* Env sector Size */
+#define CFG_ENV_SIZE		SZ_128K
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
+#define CONFIG_SKIP_RELOCATE_UBOOT	/* to a proper address, init done */
+#define CFG_NAND_BASE		0x02000000
+#define CFG_NAND_HW_ECC
+#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
+#define NAND_MAX_CHIPS		1
+#define CFG_ENV_OFFSET		0x0	/* Block 0--not used by bootcode */
+/*=====================*/
+/* Board related stuff */
+/*=====================*/
+#define CONFIG_RTC_DS1307		/* RTC chip on SCHMOOGIE */
+#define CFG_I2C_RTC_ADDR	0x6f	/* RTC chip I2C address */
+#define CONFIG_HAS_UID
+#define CONFIG_UID_DS28CM00		/* Unique ID on SCHMOOGIE */
+#define CFG_UID_ADDR		0x50	/* UID chip I2C address */
+/*==============================*/
+/* U-Boot general configuration */
+/*==============================*/
+#undef 	CONFIG_USE_IRQ			/* No IRQ/FIQ in U-Boot */
+#define CONFIG_MISC_INIT_R
+#undef CONFIG_BOOTDELAY
+#define CONFIG_BOOTFILE		"uImage"	/* Boot file name */
+#define CFG_PROMPT		"U-Boot > "	/* Monitor Command Prompt */
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size  */
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print buffer sz */
+#define CFG_MAXARGS		16		/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR		0x80700000	/* default Linux kernel load address */
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE		/* Won't work with hush so far, may be later */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+#define CONFIG_CMDLINE_EDITING
+#define CFG_LONGHELP
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+/*===================*/
+/* Linux Information */
+/*===================*/
+#define LINUX_BOOT_PARAM_ADDR	0x80000100
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTARGS		"mem=56M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
+#define CONFIG_BOOTCOMMAND	"setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot"
+/*=================*/
+/* U-Boot commands */
+/*=================*/
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_NAND
+#undef CONFIG_CMD_EEPROM
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+/*=======================*/
+/* KGDB support (if any) */
+/*=======================*/
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
diff --git a/include/configs/davinci_sonata.h b/include/configs/davinci_sonata.h
new file mode 100644
index 0000000..de8c4fa
--- /dev/null
+++ b/include/configs/davinci_sonata.h
@@ -0,0 +1,209 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * Define this to make U-Boot skip low level initialization when loaded
+ * by initial bootloader. Not required by NAND U-Boot version but IS
+ * required for a NOR version used to burn the real NOR U-Boot into
+ * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
+ * so it is NOT possible to build a U-Boot with both NAND and NOR routines.
+ * NOR U-Boot is loaded directly from Flash so it must perform all the
+ * low level initialization itself. NAND version is loaded by an initial
+ * bootloader (UBL in TI-ese) that performs such an initialization so it's
+ * skipped in NAND version. The third DaVinci boot mode loads a bootloader
+ * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
+ * performing low level init prior to loading. All that means we can NOT use
+ * NAND version to put U-Boot into NOR because it doesn't have NOR support and
+ * we can NOT use NOR version because it performs low level initialization
+ * effectively destroying itself in DDR memory. That's why a separate NOR
+ * version with this define is needed. It is loaded via UART, then one uses
+ * it to somehow download a proper NOR version built WITHOUT this define to
+ * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
+ * NOR support into the initial bootloader so it won't be needed but DaVinci
+ * static RAM might be too small for this (I have something like 2Kbytes left
+ * as of now, without NOR support) so this might've not happened...
+ *
+#define CONFIG_NOR_UART_BOOT
+ */
+
+/*=======*/
+/* Board */
+/*=======*/
+#define SONATA_BOARD
+#define CFG_NAND_SMALLPAGE
+#define CFG_USE_NOR
+/*===================*/
+/* SoC Configuration */
+/*===================*/
+#define CONFIG_ARM926EJS			/* arm926ejs CPU core */
+#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
+#define CFG_TIMERBASE		0x01c21400	/* use timer 0 */
+#define CFG_HZ_CLOCK		27000000	/* Timer Input clock freq */
+#define CFG_HZ			1000
+/*====================================================*/
+/* EEPROM definitions for Atmel 24C256BN SEEPROM chip */
+/* on Sonata/DV_EVM board. No EEPROM on schmoogie.    */
+/*====================================================*/
+#define CFG_I2C_EEPROM_ADDR_LEN		2
+#define CFG_I2C_EEPROM_ADDR		0x50
+#define CFG_EEPROM_PAGE_WRITE_BITS	6
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	20
+/*=============*/
+/* Memory Info */
+/*=============*/
+#define CFG_MALLOC_LEN		(0x10000 + 128*1024)	/* malloc() len */
+#define CFG_GBL_DATA_SIZE	128		/* reserved for initial data */
+#define CFG_MEMTEST_START	0x80000000	/* memtest start address */
+#define CFG_MEMTEST_END		0x81000000	/* 16MB RAM test */
+#define CONFIG_NR_DRAM_BANKS	1		/* we have 1 bank of DRAM */
+#define CONFIG_STACKSIZE	(256*1024)	/* regular stack */
+#define PHYS_SDRAM_1		0x80000000	/* DDR Start */
+#define PHYS_SDRAM_1_SIZE	0x08000000	/* DDR size 128MB */
+#define DDR_4BANKS				/* 4-bank DDR2 (128MB) */
+/*====================*/
+/* Serial Driver info */
+/*====================*/
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	4		/* NS16550 register size */
+#define CFG_NS16550_COM1	0x01c20000	/* Base address of UART0 */
+#define CFG_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_CONS_INDEX	1		/* use UART0 for console */
+#define CONFIG_BAUDRATE		115200		/* Default baud rate */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+/*===================*/
+/* I2C Configuration */
+/*===================*/
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_DAVINCI_I2C
+#define CFG_I2C_SPEED		80000	/* 100Kbps won't work, silicon bug */
+#define CFG_I2C_SLAVE		10	/* Bogus, master-only in U-Boot */
+/*==================================*/
+/* Network & Ethernet Configuration */
+/*==================================*/
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT	10
+/*=====================*/
+/* Flash & Environment */
+/*=====================*/
+#ifdef CFG_USE_NAND
+#undef CFG_ENV_IS_IN_FLASH
+#define CFG_NO_FLASH
+#define CFG_ENV_IS_IN_NAND		/* U-Boot env in NAND Flash  */
+#define CFG_ENV_SECT_SIZE	512	/* Env sector Size */
+#define CFG_ENV_SIZE		SZ_16K
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
+#define CONFIG_SKIP_RELOCATE_UBOOT	/* to a proper address, init done */
+#define CFG_NAND_BASE		0x02000000
+#define CFG_NAND_HW_ECC
+#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
+#define NAND_MAX_CHIPS		1
+#define CFG_ENV_OFFSET		0x0	/* Block 0--not used by bootcode */
+#define DEF_BOOTM		""
+#elif defined(CFG_USE_NOR)
+#ifdef CONFIG_NOR_UART_BOOT
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */
+#define CONFIG_SKIP_RELOCATE_UBOOT	/* to a proper address, init done */
+#else
+#undef CONFIG_SKIP_LOWLEVEL_INIT
+#undef CONFIG_SKIP_RELOCATE_UBOOT
+#endif
+#define CFG_ENV_IS_IN_FLASH
+#undef CFG_NO_FLASH
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_MAX_FLASH_BANKS	1		/* max number of flash banks */
+#define CFG_FLASH_SECT_SZ	0x20000		/* 128KB sect size AMD Flash */
+#define CFG_ENV_OFFSET		(CFG_FLASH_SECT_SZ*2)
+#define PHYS_FLASH_1		0x02000000	/* CS2 Base address 	 */
+#define CFG_FLASH_BASE		PHYS_FLASH_1	/* Flash Base for U-Boot */
+#define PHYS_FLASH_SIZE		0x2000000	/* Flash size 32MB 	 */
+#define CFG_MAX_FLASH_SECT	(PHYS_FLASH_SIZE/CFG_FLASH_SECT_SZ)
+#define CFG_ENV_SECT_SIZE	CFG_FLASH_SECT_SZ	/* Env sector Size */
+#endif
+/*==============================*/
+/* U-Boot general configuration */
+/*==============================*/
+#undef 	CONFIG_USE_IRQ			/* No IRQ/FIQ in U-Boot */
+#define CONFIG_MISC_INIT_R
+#undef CONFIG_BOOTDELAY
+#define CONFIG_BOOTFILE		"uImage"	/* Boot file name */
+#define CFG_PROMPT		"U-Boot > "	/* Monitor Command Prompt */
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size  */
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print buffer sz */
+#define CFG_MAXARGS		16		/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR		0x80700000	/* default Linux kernel load address */
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE		/* Won't work with hush so far, may be later */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+#define CONFIG_CMDLINE_EDITING
+#define CFG_LONGHELP
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+/*===================*/
+/* Linux Information */
+/*===================*/
+#define LINUX_BOOT_PARAM_ADDR	0x80000100
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTARGS		"mem=56M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
+#define CONFIG_BOOTCOMMAND	"setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2060000"
+/*=================*/
+/* U-Boot commands */
+/*=================*/
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_EEPROM
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#ifdef CFG_USE_NAND
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_NAND
+#elif defined(CFG_USE_NOR)
+#define CONFIG_CMD_JFFS2
+#else
+#error "Either CFG_USE_NAND or CFG_USE_NOR _MUST_ be defined !!!"
+#endif
+/*=======================*/
+/* KGDB support (if any) */
+/*=======================*/
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h
new file mode 100644
index 0000000..577f459
--- /dev/null
+++ b/include/configs/hcu4.h
@@ -0,0 +1,348 @@
+/*
+ *(C) Copyright 2005-2007 Netstal Maschinen AG
+ *    Niklaus Giger (Niklaus.Giger@netstal.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * hcu4.h - configuration for HCU4 board (similar to hcu5.h)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_HCU4		1		/* Board is HCU4	*/
+#define CONFIG_4xx		1		/* ... PPC4xx family	*/
+#define CONFIG_405GPr 1 /* HCU4 has a 405GPr */
+#define CONFIG_405GP 1
+#define CONFIG_4xx   1
+
+#define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+*----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
+
+
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
+#define CFG_FLASH_BASE		0xfff80000	/* start of FLASH	*/
+#define CFG_MONITOR_BASE	TEXT_BASE
+
+/* ... with on-chip memory here (4KBytes) */
+#define CFG_OCM_DATA_ADDR 0xF4000000
+#define CFG_OCM_DATA_SIZE 0x00001000
+/* Do not set up locked dcache as init ram. */
+#undef CFG_INIT_DCACHE_CS
+
+/* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
+#define CFG_TEMP_STACK_OCM 1
+
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR	/* OCM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE
+#define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+/*
+ * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * The Linux BASE_BAUD define should match this configuration.
+ *    baseBaud = cpuClock/(uartDivisor*16)
+ * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * set Linux BASE_BAUD to 403200.
+ */
+#undef CFG_EXT_SERIAL_CLOCK	       /* external serial clock */
+#undef CONFIG_SERIAL_MULTI            /* needed to be able to define
+					  CONFIG_SERIAL_SOFTWARE_FIFO */
+#undef	CFG_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
+#define CFG_BASE_BAUD	    691200
+
+/* Size (bytes) of interrupt driven serial port buffer.
+ * Set to 0 to use polling instead of interrupts.
+ * Setting to 0 will also disable RTS/CTS handshaking.
+ */
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+
+/* Set console baudrate to 9600 */
+#define CONFIG_BAUDRATE		9600
+
+
+#define CFG_BAUDRATE_TABLE						\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+
+#undef	CFG_ENV_IS_IN_NVRAM
+#undef  CFG_ENV_IS_IN_FLASH
+#define	CFG_ENV_IS_IN_EEPROM
+#undef  CFG_ENV_IS_NOWHERE
+
+#ifdef  CFG_ENV_IS_IN_EEPROM
+/* Put the environment after the SDRAM configuration */
+#define PROM_SIZE 	2048
+#define CFG_ENV_OFFSET	 512
+#define CFG_ENV_SIZE	(PROM_SIZE-CFG_ENV_OFFSET)
+#endif
+
+#ifdef CFG_ENV_IS_IN_FLASH
+/* Put the environment in Flash */
+#define CFG_ENV_SECT_SIZE	0x10000 	/* size of one complete sector	*/
+#define CFG_ENV_ADDR		((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x10000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
+ * the first internal I2C controller of the PPC440EPx
+ *----------------------------------------------------------------------*/
+#define CFG_SPD_BUS_NUM		0
+
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+/* This is the 7bit address of the device, not including P. */
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+
+/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#undef CFG_I2C_MULTI_EEPROMS
+
+
+#define CONFIG_PREBOOT	"echo;"						\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+/* Setup some board specific values for the default environment variables */
+#define CONFIG_HOSTNAME		hcu4
+#define CONFIG_IPADDR		172.25.1.42
+#define CONFIG_ETHADDR      00:60:13:00:00:00   /* Netstal Machines AG MAC */
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_SERVERIP		172.25.1.3
+
+#define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"loadaddr=0x01000000\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"		\
+	        "bootm\0"						\
+	"rootpath=/home/diagnose/eldk/ppc_4xx\0"			\
+	"bootfile=/tftpboot/hcu4/uImage\0"				\
+	"load=tftp 100000 hcu4/u-boot.bin\0"			\
+	"update=protect off FFFa0000 FFFFFFFF;era FFFa0000 FFFFFFFF;"	\
+		"cp.b 100000 FFFa0000 60000\0"			        \
+	"upd=run load;run update\0"					\
+	"vx=tftp ${loadaddr} hcu4_vx_rom;"				\
+	"setenv bootargs emac(0,0)hcu4_vx_rom e=${ipaddr} "		\
+	" h=${serverip} u=dpu pw=netstal8752 tn=hcu4 f=0x3008;"		\
+	"bootvx ${loadaddr}\0" 						\
+	""
+#define CONFIG_BOOTCOMMAND	"run vx"
+
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		1	/* PHY address			*/
+
+#define CONFIG_PHY_RESET        1	/* reset phy upon startup         */
+
+#define CONFIG_HAS_ETH0
+#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+
+/* SPD EEPROM (sdram speed config) disabled */
+#define CONFIG_SPD_EEPROM          1
+#define SPD_EEPROM_ADDRESS      0x50
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+	#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+	#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x02005400
+#define CFG_EBC_PB0CR		0xFFF18000  /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit	*/
+
+#define CFG_EBC_PB1AP		0x03041200
+#define CFG_EBC_PB1CR		0x7009A000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+
+#define CFG_EBC_PB2AP		0x02054500
+#define CFG_EBC_PB2CR		0x78018000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+
+#define CFG_EBC_PB3AP		0x01840300
+#define CFG_EBC_PB3CR		0x7c0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+
+#define CFG_EBC_PB4AP		0x01800300
+#define CFG_EBC_PB4CR		0x7e0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/
+
+#define CFG_GPIO0_TCR		0x7ffe0000  /* GPIO value */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+/* Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	CFG_FLASH_BASE	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/
+
+
+/* Configuration Port location */
+#define CONFIG_PORT_ADDR	0xF0000500
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *----------------------------------------------------------------------*/
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405GPr CPUs	*/
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#define CFG_CACHELINE_SHIFT	5	      /* log base 2 of the above value	*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#define CFG_HUSH_PARSER                 /* use "hush" command parser    */
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	    /* which serial port to use */
+#endif
+#endif	/* __CONFIG_H */
diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h
new file mode 100644
index 0000000..9085881
--- /dev/null
+++ b/include/configs/hcu5.h
@@ -0,0 +1,391 @@
+/*
+ * (C) Copyright 2007 Netstal Maschinen AG
+ * Niklaus Giger (Niklaus.Giger@netstal.com)
+ *
+ * (C) Copyright 2006-2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
+ * Alain Saurel,            AMCC/IBM, alain.saurel@fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * hcu5.h - configuration for HCU5 board (derived from sequoia.h)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_HCU5		1		/* Board is HCU5	*/
+#define CONFIG_440EPX		1		/* Specific PPC440EPx	*/
+#define CONFIG_440		1		/* ... PPC440 family	*/
+#define CONFIG_4xx		1		/* ... PPC4xx family	*/
+#define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
+
+#define CFG_BOOT_BASE_ADDR	0xfff00000
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
+#define CFG_FLASH_BASE		0xfff80000	/* start of FLASH	*/
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_OCM_BASE		0xe0010000      /* ocm			*/
+#define CFG_PCI_BASE		0xe0000000      /* Internal PCI regs	*/
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
+#define CFG_PCI_MEMBASE1	CFG_PCI_MEMBASE  + 0x10000000
+#define CFG_PCI_MEMBASE2	CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3	CFG_PCI_MEMBASE2 + 0x10000000
+
+/* Don't change either of these */
+#define CFG_PERIPHERAL_BASE	0xef600000	/* internal peripherals	*/
+
+#define CFG_USB2D0_BASE		0xe0000100
+#define CFG_USB_DEVICE		0xe0000000
+#define CFG_USB_HOST		0xe0000400
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache	*/
+#define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM			*/
+
+#define CFG_INIT_RAM_END	(4 << 10)
+#define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CFG_EXT_SERIAL_CLOCK	       /* external serial clock */
+#define CONFIG_BAUDRATE		9600
+#undef CONFIG_SERIAL_MULTI            /* needed to be able to define
+	CONFIG_SERIAL_SOFTWARE_FIFO, but
+	CONFIG_SERIAL_SOFTWARE_FIFO (16) does not work */
+/* Size (bytes) of interrupt driven serial port buffer.
+ * Set to 0 to use polling instead of interrupts.
+ * Setting to 0 will also disable RTS/CTS handshaking.
+ */
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#undef CONFIG_UART1_CONSOLE
+
+#define CFG_BAUDRATE_TABLE						\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+
+#undef	CFG_ENV_IS_IN_NVRAM
+#undef  CFG_ENV_IS_IN_FLASH
+#define	CFG_ENV_IS_IN_EEPROM
+#undef  CFG_ENV_IS_NOWHERE
+
+#ifdef  CFG_ENV_IS_IN_EEPROM
+/* Put the environment after the SDRAM and bootstrap configuration */
+#define PROM_SIZE 	2048
+#define CFG_BOOSTRAP_OPTION_OFFSET	 512
+#define CFG_ENV_OFFSET	 (CFG_BOOSTRAP_OPTION_OFFSET + 0x10)
+#define CFG_ENV_SIZE	(PROM_SIZE-CFG_ENV_OFFSET)
+#endif
+
+#ifdef CFG_ENV_IS_IN_FLASH
+/* Put the environment in Flash */
+#define CFG_ENV_SECT_SIZE	0x10000 	/* size of one complete sector	*/
+#define CFG_ENV_ADDR		((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x10000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM        (128)		/* 128 MB or 256 MB  		*/
+#define CFG_DDR_CACHED_ADDR	0x40000000	/* setup 2nd TLB cached here	*/
+#undef  CONFIG_DDR_DATA_EYE			/* Do not use DDR2 optimization	*/
+#define CONFIG_DDR_ECC		1		/* enable ECC			*/
+
+/*-----------------------------------------------------------------------
+ * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
+ * the second internal I2C controller of the PPC440EPx
+ *----------------------------------------------------------------------*/
+#define CFG_SPD_BUS_NUM		1
+
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+/* This is the 7bit address of the device, not including P. */
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+
+/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#undef CFG_I2C_MULTI_EEPROMS
+
+
+#define CONFIG_PREBOOT	"echo;"						\
+	"echo Type \"run nfs\" to mount Linux root filesystem over NFS;"\
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+/* Setup some board specific values for the default environment variables */
+#define CONFIG_HOSTNAME		hcu5
+#define CONFIG_IPADDR		172.25.1.42
+#define CONFIG_ETHADDR      	00:60:13:00:00:00   /* Netstal Machines AG MAC */
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_SERVERIP		172.25.1.3
+
+#define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"loadaddr=0x01000000\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" 	\
+		"bootm\0"						\
+		"bootfile=hcu5/uImage\0" 				\
+		"rootpath=/home/hcu/eldk/ppc_4xxFP\0"		 	\
+		"load=tftp 100000 hcu5/u-boot.bin\0"		 	\
+	"update=protect off FFFa0000 FFFFFFFF;era FFFa0000 FFFFFFFF;"	\
+		"cp.b 100000 FFFa0000 60000\0"			        \
+	"upd=run load;run update\0"					\
+	"vx=tftp ${loadaddr} hcu5/hcu5_vx_rom;" 			\
+	"setenv bootargs emac(0,0)hcu5_vx_rom e=${ipaddr} " 	 	\
+		" h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008;" \
+	"bootvx ${loadaddr}\0" \
+	""
+#define CONFIG_BOOTCOMMAND	"run vx"
+
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_M88E1111_PHY	1
+#define	CONFIG_IBM_EMAC4_V4	1
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
+
+#define CONFIG_PHY_RESET        1	/* reset phy upon startup         */
+
+#define CONFIG_HAS_ETH0
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NET_MULTI	1
+#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
+#define CONFIG_PHY1_ADDR	1
+
+/* USB */
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_STORAGE
+
+/* Comment this out to enable USB 1.1 device */
+#define USB_2_0_DEVICE
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_USB
+
+#define CONFIG_SUPPORT_VFAT
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+/* General PCI */
+#define CONFIG_PCI			/* include pci support	        */
+#undef CONFIG_PCI_PNP			/* do (not) pci plug-and-play   */
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup  */
+#define CFG_PCI_TARGBASE        0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
+
+/* Board-specific PCI */
+#define CFG_PCI_TARGET_INIT
+#define CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC				*/
+#define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever			*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH		CFG_FLASH_BASE
+#define CFG_CS_1		0xC8000000 /* CAN */
+#define CFG_CS_2		0xCC000000 /* CPLD and IMC-Bus Standard */
+#define CFG_CPLD		CFG_CS_2
+#define CFG_CS_3		0xCD000000 /* CPLD and IMC-Bus Fast  */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ * Memory Bank 0 (BOOT-FLASH) initialization
+ */
+#define CFG_BOOTFLASH_CS		0	/* Boot Flash chip connected to CSx	*/
+#define CFG_EBC_PB0AP		0x02005400
+#define CFG_EBC_PB0CR		0xFFF18000 /* (CFG_FLASH | 0xda000)  */
+#define FLASH_BASE0_PRELIM	CFG_FLASH_BASE	/* FLASH bank #0	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	32	/* max number of sectors on one chip	*/
+
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+/* Memory Bank 1 CAN-Chips initialization						*/
+#define CFG_EBC_PB1AP		0x02054500
+#define CFG_EBC_PB1CR		0xC8018000
+
+/* Memory Bank 2 CPLD/IMC-Bus standard initialization						*/
+#define CFG_EBC_PB2AP		0x01840300
+#define CFG_EBC_PB2CR		0xCC0BA000
+
+/* Memory Bank 3 IMC-Bus fast mode initialization						*/
+#define CFG_EBC_PB3AP		0x01800300
+#define CFG_EBC_PB3CR		0xCE0BA000
+
+/* Memory Bank 4 (not used) initialization						*/
+#undef CFG_EBC_PB4AP
+#undef CFG_EBC_PB4CR
+
+/* Memory Bank 5 (not used) initialization						*/
+#undef CFG_EBC_PB5AP
+#undef CFG_EBC_PB5CR
+
+#define HCU_CPLD_VERSION_REGISTER ( CFG_CPLD + 0x0F00000 )
+#define HCU_HW_VERSION_REGISTER   ( CFG_CPLD + 0x1400000 )
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *----------------------------------------------------------------------*/
+#define CFG_DCACHE_SIZE		(32<<10)  /* For AMCC 440 CPUs			*/
+#define CFG_CACHELINE_SIZE	32	      /* ...			            */
+#define CFG_CACHELINE_SHIFT	5	      /* log base 2 of the above value	*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#define CFG_HUSH_PARSER                 /* use "hush" command parser    */
+#ifdef  CFG_HUSH_PARSER
+	#define CFG_PROMPT_HUSH_PS2     "> "
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	    /* which serial port to use */
+#endif
+#endif	/* __CONFIG_H */
diff --git a/include/configs/hymod.h b/include/configs/hymod.h
index 2f64ec2..2547afb 100644
--- a/include/configs/hymod.h
+++ b/include/configs/hymod.h
@@ -406,6 +406,7 @@
 #define	CFG_ENV_SIZE		0x40000	/* Total Size of Environment Sector */
 #define CFG_ENV_SECT_SIZE	0x40000	/* see README - env sect real size */
 #define	CFG_ENV_ADDR	(CFG_FLASH_BASE+CFG_MONITOR_LEN-CFG_ENV_SECT_SIZE)
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
diff --git a/include/configs/idmr.h b/include/configs/idmr.h
index 1ab7b27..3821ebc 100644
--- a/include/configs/idmr.h
+++ b/include/configs/idmr.h
@@ -44,6 +44,8 @@
  */
 #define CONFIG_BOOTCOMMAND	"run net_nfs"
 #define CONFIG_BOOTDELAY	5
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 #define CONFIG_ETHADDR		00:06:3b:01:41:55
@@ -58,6 +60,8 @@
 #define CONFIG_PREBOOT		"echo;echo Type \"run flash_nfs\" to mount root " \
 				"filesystem over NFS; echo"
 
+#define CONFIG_MCFTMR
+
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
@@ -121,6 +125,8 @@
 #define CFG_ENV_IS_IN_FLASH
 #endif /* !CONFIG_MONITOR_IS_IN_RAM */
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 #define CFG_PROMPT		"=> "
 #define CFG_LONGHELP				/* undef to save memory */
 
@@ -147,11 +153,27 @@
 /*
  * Ethernet
  */
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT	5
-#define CFG_ENET_BD_BASE	0x480000
-#define CFG_DISCOVER_PHY	1
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
 #define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
@@ -186,7 +208,7 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /* FLASH organization */
 #define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
@@ -216,7 +238,7 @@
 						"-(user)";
 
 #if defined(CONFIG_CMD_MII)
-#error MII commands don't work on iDMR board and sholud not be enabled.
+#error "MII commands don't work on iDMR board and should not be enabled."
 #endif
 
 #endif /* _IDMR_H */
diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h
index b68c5aa..b7100e9 100644
--- a/include/configs/jupiter.h
+++ b/include/configs/jupiter.h
@@ -145,12 +145,9 @@
 
 #if 0
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 110ad44..7908e5a 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -42,7 +42,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 
 /*-----------------------------------------------------------------------
@@ -67,11 +66,11 @@
 #define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */
 
 #define CFG_PCIE0_CFGBASE	0xc0000000
-#define CFG_PCIE0_XCFGBASE	0xc0000400
-#define CFG_PCIE1_CFGBASE	0xc0001000
-#define CFG_PCIE1_XCFGBASE	0xc0001400
-#define CFG_PCIE2_CFGBASE	0xc0002000
-#define CFG_PCIE2_XCFGBASE	0xc0002400
+#define CFG_PCIE1_CFGBASE	0xc1000000
+#define CFG_PCIE2_CFGBASE	0xc2000000
+#define CFG_PCIE0_XCFGBASE	0xc3000000
+#define CFG_PCIE1_XCFGBASE	0xc3001000
+#define CFG_PCIE2_XCFGBASE	0xc3002000
 
 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
@@ -202,6 +201,7 @@
 		"setenv filesize;saveenv\0"				\
 	"upd=run load;run update\0"					\
 	"kozio=bootm ffc60000\0"					\
+	"pciconfighost=1\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -323,7 +323,7 @@
 #define CONFIG_PCI			/* include pci support		*/
 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
-#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE
 
 /* Board-specific PCI */
 #define CFG_PCI_TARGET_INIT		/* let board init pci target    */
diff --git a/include/configs/luan.h b/include/configs/luan.h
index 72aae09..a09dd74 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -39,7 +39,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -136,7 +135,6 @@
 #define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
 #define SPD_EEPROM_ADDRESS	{0x53, 0x52}	/* SPD i2c spd addresses*/
 #define CONFIG_DDR_ECC		1	/* with ECC support		*/
-#define CFG_44x_DDR2_CKTR_180	1	/* use 180 deg advance		*/
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -213,7 +211,6 @@
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif
 
-
 /*
  * BOOTP options
  */
@@ -222,7 +219,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -230,7 +226,6 @@
 
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
@@ -242,7 +237,6 @@
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
-
 /*
  * Miscellaneous configurable options
  */
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index ef9ab22..be48324 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -34,8 +34,8 @@
 #define CONFIG_SYS_CLK_FREQ	33300000	/* external freq to pll	*/
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
+#define CONFIG_BOARD_POSTCLK_INIT 1	/* Call board_postclk_init	*/
 #define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -46,7 +46,7 @@
 
 #define CFG_BOOT_BASE_ADDR	0xf0000000
 #define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
-#define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
+#define CFG_FLASH_BASE		0xf8000000	/* start of FLASH	*/
 #define CFG_MONITOR_BASE	TEXT_BASE
 #define CFG_LIME_BASE_0         0xc0000000
 #define CFG_LIME_BASE_1         0xc1000000
@@ -72,13 +72,14 @@
  * Initial RAM & stack pointer
  *----------------------------------------------------------------------*/
 /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache	*/
-#define CFG_INIT_RAM_OCM	1		/* OCM as init ram	*/
 #define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM			*/
+#define CFG_OCM_DATA_ADDR	CFG_OCM_BASE
 
 #define CFG_INIT_RAM_END	(4 << 10)
 #define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
 
 /*-----------------------------------------------------------------------
  * Serial Port
@@ -103,9 +104,11 @@
 #define CFG_FLASH_CFI				/* The flash is CFI compatible	*/
 #define CFG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/
 
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CFG_FLASH0		0xFC000000
+#define CFG_FLASH1		0xF8000000
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH1, CFG_FLASH0 }
 
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
 #define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
@@ -133,35 +136,63 @@
 #define CONFIG_DDR_DATA_EYE	1		/* use DDR2 optimization	*/
 #if 0 /* test-only: disable ECC for now */
 #define CONFIG_DDR_ECC		1		/* enable ECC			*/
+#define CFG_POST_ECC_ON		CFG_POST_ECC
+#else
+#define CFG_POST_ECC_ON		0
 #endif
 
+/* POST support */
+#define CONFIG_POST		(CFG_POST_CACHE    | \
+				 CFG_POST_CPU	   | \
+				 CFG_POST_ECC_ON   | \
+				 CFG_POST_ETHER	   | \
+				 CFG_POST_FPU	   | \
+				 CFG_POST_I2C	   | \
+				 CFG_POST_MEMORY   | \
+				 CFG_POST_RTC      | \
+				 CFG_POST_SPR      | \
+				 CFG_POST_UART)
+
+#define CFG_POST_CACHE_ADDR	0x10000000	/* free virtual address		*/
+#define CONFIG_LOGBUFFER
+#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CFG_I2C_SPEED		100000		/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F
 
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_I2C_EEPROM_ADDR	0x53	/* EEPROM AT24C128		*/
+#define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
+#define CFG_EEPROM_PAGE_WRITE_BITS 6	/* The Atmel AT24C128 has	*/
+					/* 64 byte page write mode using*/
+					/* last 6 bits of the address	*/
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
 #define CONFIG_RTC_PCF8563	1		/* enable Philips PCF8563 RTC	*/
 #define CFG_I2C_RTC_ADDR	0x51		/* Philips PCF8563 RTC address	*/
+#define CFG_I2C_KEYBD_ADDR	0x56		/* PIC LWE keyboard		*/
+
+#define	CONFIG_POST_KEY_MAGIC	"3C+3E"	/* press F3 + F5 keys to force POST */
+#if 0
+#define	CONFIG_AUTOBOOT_KEYED		/* Enable "password" protection	*/
+#define CONFIG_AUTOBOOT_PROMPT	"\nEnter password - autoboot in %d sec...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"  "	/* "password"	*/
+#endif
 
-#define CONFIG_PREBOOT	"echo;"						\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
+#define	CONFIG_PREBOOT		"setenv bootdelay 15"
 
 #undef	CONFIG_BOOTARGS
 
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"hostname=lwmon5\0"						\
 	"netdev=eth0\0"							\
+	"unlock=yes\0"							\
+	"logversion=2\0"						\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
@@ -183,6 +214,8 @@
 	"update=protect off FFF80000 FFFFFFFF;era FFF80000 FFFFFFFF;"	\
 		"cp.b 200000 FFF80000 80000\0"			        \
 	"upd=run load;run update\0"					\
+	"lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;"	\
+		"autoscr 200000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -200,6 +233,7 @@
 #define CONFIG_PHY_ADDR		3	/* PHY address, See schematics	*/
 
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup         */
+#define CONFIG_PHY_RESET_DELAY	300
 
 #define CONFIG_HAS_ETH0
 #define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
@@ -223,7 +257,6 @@
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION
 
-
 /*
  * BOOTP options
  */
@@ -232,7 +265,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -247,6 +279,7 @@
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
+#define CONFIG_CMD_LOG
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
@@ -259,7 +292,6 @@
 #define CONFIG_CMD_USB
 #endif
 
-
 /*-----------------------------------------------------------------------
  * Miscellaneous configurable options
  *----------------------------------------------------------------------*/
@@ -322,7 +354,7 @@
 
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
 #define CFG_EBC_PB0AP		0x03050200
-#define CFG_EBC_PB0CR		(CFG_FLASH | 0xdc000)
+#define CFG_EBC_PB0CR		(CFG_FLASH | 0xfc000)
 
 /* Memory Bank 1 (Lime) initialization						*/
 #define CFG_EBC_PB1AP		0x01004380
@@ -342,14 +374,24 @@
  * Graphics (Fujitsu Lime)
  *----------------------------------------------------------------------*/
 /* SDRAM Clock frequency adjustment register */
-#define CFG_LIME_SDRAM_CLOCK	0xC1FC0000
-/* Lime Clock frequency is to set 133MHz */
+#define CFG_LIME_SDRAM_CLOCK	0xC1FC0038
+/* Lime Clock frequency is to set 100MHz */
+#define CFG_LIME_CLOCK_100MHZ	0x00000
+#if 0
+/* Lime Clock frequency for 133MHz */
 #define CFG_LIME_CLOCK_133MHZ	0x10000
+#endif
 
 /* SDRAM Parameter register */
 #define CFG_LIME_MMR		0xC1FCFFFC
-/* SDRAM parameter value */
+/* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars
+   and pixel flare on display when 133MHz was configured. According to
+   SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */
+#ifdef CFG_LIME_CLOCK_133MHZ
+#define CFG_LIME_MMR_VALUE	0x414FB7F3
+#else
 #define CFG_LIME_MMR_VALUE	0x414FB7F2
+#endif
 
 /*-----------------------------------------------------------------------
  * GPIO Setup
@@ -357,9 +399,11 @@
 #define CFG_GPIO_PHY1_RST	12
 #define CFG_GPIO_FLASH_WP	14
 #define CFG_GPIO_PHY0_RST	22
-#define CFG_GPIO_WATCHDOG	58
+#define CFG_GPIO_EEPROM_EXT_WP	55
+#define CFG_GPIO_EEPROM_INT_WP	57
 #define CFG_GPIO_LIME_S		59
 #define CFG_GPIO_LIME_RST	60
+#define CFG_GPIO_WATCHDOG	63
 
 /*-----------------------------------------------------------------------
  * PPC440 GPIO Configuration
diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h
index 744f551..cc2dbcd 100644
--- a/include/configs/mcc200.h
+++ b/include/configs/mcc200.h
@@ -111,11 +111,13 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_USB
 
+#undef	CONFIG_CMD_NET
+
 
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
+#define CONFIG_BOOTDELAY	1	/* autoboot after 1 second */
 
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
@@ -131,20 +133,30 @@
 # define CFG__LINUX_CONSOLE	"ttyS0"
 #else
 # define CFG__BOARDNAME		"mcc200"
-# define CFG__LINUX_CONSOLE	"ttyEU7"
+# define CFG__LINUX_CONSOLE	"ttyEU5"
 #endif
 
+/* Network */
+#define CONFIG_ETHADDR	00:17:17:ff:00:00
+#define CONFIG_IPADDR	10.76.9.29
+#define CONFIG_SERVERIP	10.76.9.1
+
+#include <version.h> /* For U-Boot version */
+
 #define CONFIG_EXTRA_ENV_SETTINGS					\
+	"ubootver=" U_BOOT_VERSION "\0"					\
 	"netdev=eth0\0"							\
 	"hostname=" CFG__BOARDNAME "\0"					\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"ramargs=setenv bootargs root=/dev/mtdblock2 "			\
+		"rootfstype=cramfs\0"					\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addcons=setenv bootargs ${bootargs} "				\
-		"console=${console},${baudrate}\0"			\
+		"console=${console},${baudrate} "		\
+		"ubootver=${ubootver} board=${board}\0"	\
 	"flash_nfs=run nfsargs addip addcons;"				\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip addcons;"				\
@@ -156,6 +168,7 @@
 	"bootfile=/tftpboot/" CFG__BOARDNAME "/uImage\0"		\
 	"load=tftp 200000 /tftpboot/" CFG__BOARDNAME "/u-boot.bin\0"	\
 	"text_base=" MK_STR(TEXT_BASE) "\0"				\
+	"kernel_addr=0xFC0C0000\0"					\
 	"update=protect off ${text_base} +${filesize};"			\
 		"era ${text_base} +${filesize};"			\
 		"cp.b 200000 ${text_base} ${filesize}\0"		\
@@ -256,7 +269,7 @@
 /*
  * Ethernet configuration
  */
-#define CONFIG_MPC5xxx_FEC	1
+/*#define CONFIG_MPC5xxx_FEC	1*/
 /*
  * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
  */
@@ -337,6 +350,13 @@
 #define CFG_CS1_SIZE		0x00001000
 #define CFG_CS1_CFG		0x1d300
 
+/* Leica - build revision resistors */
+/*
+#define CFG_CS3_START		0x80020000
+#define CFG_CS3_SIZE		0x00000004
+#define CFG_CS3_CFG		0x1d300
+*/
+
 /*
  *  Select one of quarts as a default
  * console. If undefined - PSC console
@@ -392,4 +412,8 @@
 #define CONFIG_USB_CLOCK	0x0001BBBB
 #define CONFIG_USB_CONFIG	0x00005000
 
+#define CONFIG_AUTOBOOT_KEYED		/* use key strings to stop autoboot	*/
+#define CONFIG_AUTOBOOT_STOP_STR	"432"
+#define CONFIG_SILENT_CONSOLE	1
+
 #endif /* __CONFIG_H */
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index e0a827f..9a21632 100644
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -417,11 +417,9 @@ extern void __led_set(led_id_t id, int state);
 #define CFG_RESET_ADDRESS	0xfff00100
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h
index f4f33f3..bd3107a 100644
--- a/include/configs/mpc7448hpc2.h
+++ b/include/configs/mpc7448hpc2.h
@@ -80,9 +80,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,7448@0"
 #define OF_TSI			"tsi108@c0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
diff --git a/include/configs/p3mx.h b/include/configs/p3mx.h
index 8ae38cb..bec442d 100644
--- a/include/configs/p3mx.h
+++ b/include/configs/p3mx.h
@@ -60,7 +60,6 @@
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 #define CONFIG_BOARD_EARLY_INIT_R 1     /* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R      1	/* Call misc_init_r()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index 8e51d2d..7653ba1 100644
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -266,7 +266,10 @@
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_ELF
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
 #define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
@@ -274,12 +277,10 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_REISER
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_USB
 
-
 #define CONFIG_SUPPORT_VFAT
 
 /*
@@ -488,10 +489,4 @@
 /* Offset for alternate registers	*/
 #define CFG_ATA_ALT_OFFSET	(0x0000)
 
-/* These addresses need to be shifted one place to the left
- * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0)
- * These values are shifted
- */
-#define CFG_ATA_PORT_ADDR(port) ((port) << 1)
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/r5200.h b/include/configs/r5200.h
index 0e743bb..fc7658b 100644
--- a/include/configs/r5200.h
+++ b/include/configs/r5200.h
@@ -39,13 +39,10 @@
 #define CONFIG_M5271			/* define processor type */
 #define CONFIG_R5200			/* define board type */
 
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT 5
-
-#define CONFIG_IPADDR 192.168.0.172
-#define CONFIG_SERVERIP 192.168.0.148
-#define CONFIG_ETHADDR 00:06:3b:00:44:55
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
@@ -87,6 +84,27 @@
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 /* Note: We only copy one sectors worth of application code from location
  * 10200000 for speed purposes.  Increase the size if necessary */
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 1831bef..e7d8a5a 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -313,9 +313,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8349@0"
 #define OF_SOC			"soc8349@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -410,6 +407,8 @@
 #define TSEC2_PHY_ADDR		0x1a
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -660,6 +659,7 @@
 #define CONFIG_ENV_OVERWRITE
 
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR		00:a0:1e:a0:13:8d
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		00:a0:1e:a0:13:8e
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
new file mode 100644
index 0000000..54eac38
--- /dev/null
+++ b/include/configs/sbc8641d.h
@@ -0,0 +1,606 @@
+/*
+ * Copyright 2007 Wind River Systems <www.windriver.com>
+ * Copyright 2007 Embedded Specialties, Inc.
+ * Joe Hamman <joe.hamman@embeddedspecialties.com>
+ *
+ * Copyright 2006 Freescale Semiconductor.
+ *
+ * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * SBC8641D board configuration file
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_MPC86xx		1	/* MPC86xx */
+#define CONFIG_MPC8641		1	/* MPC8641 specific */
+#define CONFIG_SBC8641D		1	/* SBC8641D board specific */
+#define CONFIG_NUM_CPUS         2       /* Number of CPUs in the system */
+#define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
+
+#ifdef RUN_DIAG
+#define CFG_DIAG_ADDR        0xff800000
+#endif
+
+#define CFG_RESET_ADDRESS    0xfff00100
+
+#define CONFIG_PCI		1	/* Enable PCIE */
+#define CONFIG_PCI1		1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCI2		1	/* PCIE controler 2 (slot 2) */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#undef CONFIG_SPD_EEPROM		/* Do not use SPD EEPROM for DDR setup*/
+#undef CONFIG_DDR_DLL			/* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+#undef CONFIG_DDR_ECC  			/* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+#define CONFIG_NUM_DDR_CONTROLLERS     2
+#define CACHE_LINE_INTERLEAVING		0x20000000
+#define PAGE_INTERLEAVING		0x21000000
+#define BANK_INTERLEAVING		0x22000000
+#define SUPER_BANK_INTERLEAVING		0x23000000
+
+
+#define CONFIG_ALTIVEC          1
+
+/*
+ * L2CR setup -- make sure this is right for your board!
+ */
+#define CFG_L2
+#define L2_INIT		0
+#define L2_ENABLE	(L2CR_L2E)
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST				/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00200000	/* memtest region */
+#define CFG_MEMTEST_END		0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xf8000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+#define CFG_PCI1_ADDR		(CFG_CCSRBAR+0x8000)
+#define CFG_PCI2_ADDR		(CFG_CCSRBAR+0x9000)
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE2	0x10000000	/* DDR bank 2 */
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CFG_SDRAM_BASE2		CFG_DDR_SDRAM_BASE2
+#define CONFIG_VERY_BIG_RAM
+
+#define MPC86xx_DDR_SDRAM_CLK_CNTL
+
+#if defined(CONFIG_SPD_EEPROM)
+    /*
+     * Determine DDR configuration from I2C interface.
+     */
+    #define SPD_EEPROM_ADDRESS1		0x51		/* DDR DIMM */
+    #define SPD_EEPROM_ADDRESS2		0x52		/* DDR DIMM */
+    #define SPD_EEPROM_ADDRESS3		0x53		/* DDR DIMM */
+    #define SPD_EEPROM_ADDRESS4		0x54		/* DDR DIMM */
+
+#else
+    /*
+     * Manually set up DDR1 & DDR2 parameters
+     */
+
+    #define CFG_SDRAM_SIZE	512		/* DDR is 512MB */
+
+    #define CFG_DDR_CS0_BNDS	0x0000000F
+    #define CFG_DDR_CS1_BNDS	0x00000000
+    #define CFG_DDR_CS2_BNDS	0x00000000
+    #define CFG_DDR_CS3_BNDS	0x00000000
+    #define CFG_DDR_CS0_CONFIG	0x80010102
+    #define CFG_DDR_CS1_CONFIG	0x00000000
+    #define CFG_DDR_CS2_CONFIG	0x00000000
+    #define CFG_DDR_CS3_CONFIG	0x00000000
+    #define CFG_DDR_EXT_REFRESH 0x00000000
+    #define CFG_DDR_TIMING_0	0x00220802
+    #define CFG_DDR_TIMING_1	0x38377322
+    #define CFG_DDR_TIMING_2	0x002040c7
+    #define CFG_DDR_CFG_1A	0x43008008
+    #define CFG_DDR_CFG_2	0x24401000
+    #define CFG_DDR_MODE_1	0x23c00542
+    #define CFG_DDR_MODE_2	0x00000000
+    #define CFG_DDR_MODE_CTL	0x00000000
+    #define CFG_DDR_INTERVAL	0x05080100
+    #define CFG_DDR_DATA_INIT	0x00000000
+    #define CFG_DDR_CLK_CTRL	0x03800000
+    #define CFG_DDR_CFG_1B	0xC3008008
+
+    #define CFG_DDR2_CS0_BNDS	0x0010001F
+    #define CFG_DDR2_CS1_BNDS	0x00000000
+    #define CFG_DDR2_CS2_BNDS	0x00000000
+    #define CFG_DDR2_CS3_BNDS	0x00000000
+    #define CFG_DDR2_CS0_CONFIG	0x80010102
+    #define CFG_DDR2_CS1_CONFIG	0x00000000
+    #define CFG_DDR2_CS2_CONFIG	0x00000000
+    #define CFG_DDR2_CS3_CONFIG	0x00000000
+    #define CFG_DDR2_EXT_REFRESH 0x00000000
+    #define CFG_DDR2_TIMING_0	0x00220802
+    #define CFG_DDR2_TIMING_1	0x38377322
+    #define CFG_DDR2_TIMING_2	0x002040c7
+    #define CFG_DDR2_CFG_1A	0x43008008
+    #define CFG_DDR2_CFG_2	0x24401000
+    #define CFG_DDR2_MODE_1	0x23c00542
+    #define CFG_DDR2_MODE_2	0x00000000
+    #define CFG_DDR2_MODE_CTL	0x00000000
+    #define CFG_DDR2_INTERVAL	0x05080100
+    #define CFG_DDR2_DATA_INIT	0x00000000
+    #define CFG_DDR2_CLK_CTRL	0x03800000
+    #define CFG_DDR2_CFG_1B	0xC3008008
+
+
+#endif
+
+/* #define CFG_ID_EEPROM	1
+#define ID_EEPROM_ADDR 0x57 */
+
+/*
+ * The SBC8641D contains 16MB flash space at ff000000.
+ */
+#define CFG_FLASH_BASE      0xff000000  /* start of FLASH 16M */
+
+/* Flash */
+#define CFG_BR0_PRELIM		0xff001001	/* port size 16bit */
+#define CFG_OR0_PRELIM		0xff006e65	/* 16MB Boot Flash area */
+
+/* 64KB EEPROM */
+#define CFG_BR1_PRELIM		0xf0000801	/* port size 16bit */
+#define CFG_OR1_PRELIM		0xffff6e65	/* 64K EEPROM area */
+
+/* EPLD - User switches, board id, LEDs */
+#define CFG_BR2_PRELIM		0xf1000801	/* port size 16bit */
+#define CFG_OR2_PRELIM		0xfff06e65	/* EPLD (switches, board ID, LEDs) area */
+
+/* Local bus SDRAM 128MB */
+#define CFG_BR3_PRELIM		0xe0001861	/* port size ?bit */
+#define CFG_OR3_PRELIM		0xfc006cc0	/* 128MB local bus SDRAM area (1st half) */
+#define CFG_BR4_PRELIM		0xe4001861	/* port size ?bit */
+#define CFG_OR4_PRELIM		0xfc006cc0	/* 128MB local bus SDRAM area (2nd half) */
+
+/* Disk on Chip (DOC) 128MB */
+#define CFG_BR5_PRELIM		0xe8001001	/* port size ?bit */
+#define CFG_OR5_PRELIM		0xf8006e65	/* 128MB local bus SDRAM area (2nd half) */
+
+/* LCD */
+#define CFG_BR6_PRELIM		0xf4000801	/* port size ?bit */
+#define CFG_OR6_PRELIM		0xfff06e65	/* 128MB local bus SDRAM area (2nd half) */
+
+/* Control logic & misc peripherals */
+#define CFG_BR7_PRELIM		0xf2000801	/* port size ?bit */
+#define CFG_OR7_PRELIM		0xfff06e65	/* 128MB local bus SDRAM area (2nd half) */
+
+#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
+#define CFG_MAX_FLASH_SECT	131		/* sectors per device */
+
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_WRITE_SWAPPED_DATA
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_PROTECTION
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK	1
+#ifndef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR	0x0fd00000	/* Initial RAM address */
+#else
+#define CFG_INIT_RAM_ADDR	0xf8400000	/* Initial RAM address */
+#endif
+#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX     1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree to kernel
+ */
+#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+#define OF_CPU		"PowerPC,8641@0"
+#define OF_SOC		"soc@f8000000"
+#define OF_TBCLK	(bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH	"/soc@f8000000/serial@4500"
+
+#define CFG_64BIT_VSPRINTF	1
+#define CFG_64BIT_STRTOUL	1
+
+/*
+ * I2C
+ */
+#define	CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define	CONFIG_HARD_I2C		/* I2C with hardware support*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET		0x3100
+
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE	0xc0000000	/* base address */
+#define CFG_RIO_MEM_PHYS	CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE	0x20000000	/* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_IO_BASE	0xe2000000
+#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS      0x00000000
+#define CFG_PCI_MEMORY_PHYS     0x00000000
+#define CFG_PCI_MEMORY_SIZE     0x80000000
+
+#define CFG_PCI2_MEM_BASE	0xa0000000
+#define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI2_IO_BASE	0xe3000000
+#define CFG_PCI2_IO_PHYS	CFG_PCI2_IO_BASE
+#define CFG_PCI2_IO_SIZE	0x1000000	/* 16M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
+
+#undef CFG_SCSI_SCAN_BUS_REVERSE
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+    #define PCI_ENET0_IOADDR	0xe0000000
+    #define PCI_ENET0_MEMADDR	0xe0000000
+    #define PCI_IDSEL_NUMBER	0x0c 	/* slot0->3(IDSEL)=12->15 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+
+#define CONFIG_DOS_PARTITION
+#undef CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID	4
+#define CFG_SCSI_MAX_LUN	1
+#define CFG_SCSI_MAX_DEVICE 	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
+#endif
+
+#endif	/* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 	1
+#endif
+
+/* #define CONFIG_MII		1 */	/* MII PHY management */
+
+#define CONFIG_TSEC1    1
+#define CONFIG_TSEC1_NAME       "eTSEC1"
+#define CONFIG_TSEC2    1
+#define CONFIG_TSEC2_NAME       "eTSEC2"
+#define CONFIG_TSEC3    1
+#define CONFIG_TSEC3_NAME       "eTSEC3"
+#define CONFIG_TSEC4    1
+#define CONFIG_TSEC4_NAME       "eTSEC4"
+
+#define TSEC1_PHY_ADDR		0x1F
+#define TSEC2_PHY_ADDR		0x00
+#define TSEC3_PHY_ADDR		0x01
+#define TSEC4_PHY_ADDR		0x02
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC3_PHYIDX		0
+#define TSEC4_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define TSEC3_FLAGS		TSEC_GIGABIT
+#define TSEC4_FLAGS		TSEC_GIGABIT
+
+#define CFG_TBIPA_VALUE	0x1e	/* Set TBI address not to conflict with TSEC1_PHY_ADDR */
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * BAT0         2G     Cacheable, non-guarded
+ * 0x0000_0000  2G     DDR
+ */
+#define CFG_DBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U	(BATU_BL_2G | BATU_VS | BATU_VP)
+#define CFG_IBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CFG_IBAT0U	CFG_DBAT0U
+
+/*
+ * BAT1         1G     Cache-inhibited, guarded
+ * 0x8000_0000  512M   PCI-Express 1 Memory
+ * 0xa000_0000  512M   PCI-Express 2 Memory
+ *	Changed it for operating from 0xd0000000
+ */
+#define CFG_DBAT1L	( CFG_PCI1_MEM_BASE | BATL_PP_RW \
+			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U	(CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT1L	(CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U	CFG_DBAT1U
+
+/*
+ * BAT2         512M   Cache-inhibited, guarded
+ * 0xc000_0000  512M   RapidIO Memory
+ */
+#define CFG_DBAT2L	(CFG_RIO_MEM_BASE | BATL_PP_RW \
+			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U	(CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L	(CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U	CFG_DBAT2U
+
+/*
+ * BAT3         4M     Cache-inhibited, guarded
+ * 0xf800_0000  4M     CCSR
+ */
+#define CFG_DBAT3L	( CFG_CCSRBAR | BATL_PP_RW \
+			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U	(CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L	(CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U	CFG_DBAT3U
+
+/*
+ * BAT4         32M    Cache-inhibited, guarded
+ * 0xe200_0000  16M    PCI-Express 1 I/O
+ * 0xe300_0000  16M    PCI-Express 2 I/0
+ *    Note that this is at 0xe0000000
+ */
+#define CFG_DBAT4L	( CFG_PCI1_IO_BASE | BATL_PP_RW \
+			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U	(CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L	(CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U	CFG_DBAT4U
+
+/*
+ * BAT5         128K   Cacheable, non-guarded
+ * 0xe401_0000  128K   Init RAM for stack in the CPU DCache (no backing memory)
+ */
+#define CFG_DBAT5L	(CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT5U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_IBAT5L	CFG_DBAT5L
+#define CFG_IBAT5U	CFG_DBAT5U
+
+/*
+ * BAT6         32M    Cache-inhibited, guarded
+ * 0xfe00_0000  32M    FLASH
+ */
+#define CFG_DBAT6L	((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
+			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U	((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L	((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U	CFG_DBAT6U
+
+#define CFG_DBAT7L	0x00000000
+#define CFG_DBAT7U	0x00000000
+#define CFG_IBAT7L	0x00000000
+#define CFG_IBAT7U	0x00000000
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+#define CFG_ENV_SIZE		0x2000
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#include <config_cmd_default.h>
+    #define CONFIG_CMD_PING
+    #define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	*/
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+    #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+    #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE		32768
+#define CFG_CACHELINE_SIZE	32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR   02:E0:0C:00:00:01
+#define CONFIG_ETH1ADDR  02:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR  02:E0:0C:00:02:FD
+#define CONFIG_ETH3ADDR  02:E0:0C:00:03:FD
+#endif
+
+#define CONFIG_HAS_ETH0		1
+#define CONFIG_HAS_ETH1		1
+#define CONFIG_HAS_ETH2		1
+#define CONFIG_HAS_ETH3		1
+
+#define CONFIG_IPADDR		192.168.0.50
+
+#define CONFIG_HOSTNAME		sbc8641d
+#define CONFIG_ROOTPATH		/opt/eldk/ppc_74xx
+#define CONFIG_BOOTFILE		uImage
+
+#define CONFIG_SERVERIP		192.168.0.2
+#define CONFIG_GATEWAYIP	192.168.0.1
+#define CONFIG_NETMASK		255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+   "netdev=eth0\0"							\
+   "consoledev=ttyS0\0"							\
+   "ramdiskaddr=2000000\0"						\
+   "ramdiskfile=uRamdisk\0"						\
+   "dtbaddr=400000\0"							\
+   "dtbfile=sbc8641d.dtb\0"						\
+   "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0"	\
+   "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0"	\
+   "maxcpus=1"
+
+#define CONFIG_NFSBOOTCOMMAND						\
+   "setenv bootargs root=/dev/nfs rw "					\
+      "nfsroot=$serverip:$rootpath "					\
+      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "	\
+      "console=$consoledev,$baudrate $othbootargs;"			\
+   "tftp $loadaddr $bootfile;"						\
+   "tftp $dtbaddr $dtbfile;"						\
+   "bootm $loadaddr - $dtbaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+   "setenv bootargs root=/dev/ram rw "					\
+      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "	\
+      "console=$consoledev,$baudrate $othbootargs;"			\
+   "tftp $ramdiskaddr $ramdiskfile;"					\
+   "tftp $loadaddr $bootfile;"						\
+   "tftp $dtbaddr $dtbfile;"						\
+   "bootm $loadaddr $ramdiskaddr $dtbaddr"
+
+#define CONFIG_FLASHBOOTCOMMAND						\
+   "setenv bootargs root=/dev/ram rw "					\
+      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "	\
+      "console=$consoledev,$baudrate $othbootargs;"			\
+   "bootm ffd00000 ffb00000 ffa00000"
+
+#define CONFIG_BOOTCOMMAND  CONFIG_FLASHBOOTCOMMAND
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 3f75a44..c2e1386 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -343,6 +343,11 @@
 #define CONFIG_CMD_USB
 #endif
 
+#ifndef CONFIG_RAINIER
+#define CFG_POST_FPU_ON		CFG_POST_FPU
+#else
+#define CFG_POST_FPU_ON		0
+#endif
 
 /* POST support */
 #define CONFIG_POST		(CFG_POST_MEMORY   | \
@@ -350,7 +355,7 @@
 				 CFG_POST_UART	   | \
 				 CFG_POST_I2C	   | \
 				 CFG_POST_CACHE	   | \
-				 CFG_POST_FPU	   | \
+				 CFG_POST_FPU_ON   | \
 				 CFG_POST_ETHER	   | \
 				 CFG_POST_SPR)
 
@@ -395,7 +400,8 @@
  *----------------------------------------------------------------------*/
 /* General PCI */
 #define CONFIG_PCI			/* include pci support	        */
-#undef CONFIG_PCI_PNP			/* do (not) pci plug-and-play   */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play   */
+#define CFG_PCI_CACHE_LINE_SIZE	0 /* to avoid problems with PNP */
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup  */
 #define CFG_PCI_TARGBASE        0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
 
diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h
index b4ab9ad..2efc8f1 100644
--- a/include/configs/spc1920.h
+++ b/include/configs/spc1920.h
@@ -31,14 +31,9 @@
 #undef	CONFIG_8xx_CONS_NONE
 
 #define CONFIG_MII
-/* #define MII_DEBUG */
-/* #define CONFIG_FEC_ENET */
 #undef CONFIG_ETHER_ON_FEC1
 #define CONFIG_ETHER_ON_FEC2
 #define FEC_ENET
-/* #define CONFIG_FEC2_PHY_NORXERR */
-/* #define CFG_DISCOVER_PHY */
-/* #define CONFIG_PHY_ADDR		0x1 */
 #define CONFIG_FEC2_PHY		1
 
 #define CONFIG_BAUDRATE		19200
@@ -100,14 +95,12 @@
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_NET
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 
-#undef CONFIG_CMD_NET
-
-
 /*
  * Miscellaneous configurable options
  */
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 1f41cf7..c5ae0cd 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -234,12 +234,13 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPS85XX_FEC
 
 #define TSEC1_PHY_ADDR		2
 #define TSEC2_PHY_ADDR		4
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #define CONFIG_ETHPRIME		"TSEC0"
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
@@ -378,6 +379,7 @@
 
 /*Note: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	 00:e0:0c:07:9b:8a
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:e0:0c:07:9b:8b
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 55e2c8d..b41dafa 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -230,7 +230,7 @@
 #define CFG_PCI2_IO_SIZE	0x01000000	/* 16M */
 
 #if defined(CONFIG_PCI) 		/* PCI Ethernet card */
-
+#define CONFIG_MPC85XX_PCI2	1
 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP			/* do pci plug-and-play */
 
@@ -260,12 +260,13 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#define CONFIG_MPS85XX_FEC
 
 #define TSEC1_PHY_ADDR		2
 #define TSEC2_PHY_ADDR		4
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #define CONFIG_ETHPRIME		"TSEC0"
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
@@ -406,6 +407,7 @@
 
 /*Note: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	 00:e0:0c:07:9b:8a
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:e0:0c:07:9b:8b
diff --git a/include/configs/stxxtc.h b/include/configs/stxxtc.h
index 0dbf4b7..b035857 100644
--- a/include/configs/stxxtc.h
+++ b/include/configs/stxxtc.h
@@ -592,9 +592,6 @@ typedef unsigned int led_id_t;
 /* pass open firmware flat tree */
 #define CONFIG_OF_FLAT_TREE	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,MPC870@0"
 #define OF_TBCLK		(MPC8XX_HZ / 16)
 #define CONFIG_OF_HAS_BD_T	1
diff --git a/include/configs/taihu.h b/include/configs/taihu.h
new file mode 100644
index 0000000..d623e56
--- /dev/null
+++ b/include/configs/taihu.h
@@ -0,0 +1,476 @@
+/*
+ * (C) Copyright 2000-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2005-2007
+ * Beijing UD Technology Co., Ltd., taihusupport@amcc.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+
+#define CONFIG_405EP		1	/* this is a PPC405 CPU */
+#define CONFIG_4xx		1	/*  member of PPC4xx family */
+#define CONFIG_TAIHU	        1	/*  on a taihu board */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f */
+
+#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
+
+#define CONFIG_NO_SERIAL_EEPROM
+
+/*----------------------------------------------------------------------------*/
+#ifdef CONFIG_NO_SERIAL_EEPROM
+
+/*
+!-------------------------------------------------------------------------------
+! PLL settings for 333MHz CPU, 111MHz PLB/SDRAM, 55MHz EBC, 33MHz PCI,
+! assuming a 33MHz input clock to the 405EP from the C9531.
+!-------------------------------------------------------------------------------
+*/
+#define PLLMR0_333_111_55_37 (PLL_CPUDIV_1 | PLL_PLBDIV_3 |  \
+			      PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 |  \
+			      PLL_MALDIV_1 | PLL_PCIDIV_3)
+#define PLLMR1_333_111_55_37 (PLL_FBKDIV_10  |  \
+			      PLL_FWDDIVA_3 | PLL_FWDDIVB_3 |  \
+			      PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
+#define PLLMR0_333_111_55_111 (PLL_CPUDIV_1 | PLL_PLBDIV_3 |  \
+			       PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 |  \
+			       PLL_MALDIV_1 | PLL_PCIDIV_1)
+#define PLLMR1_333_111_55_111 (PLL_FBKDIV_10  |  \
+			       PLL_FWDDIVA_3 | PLL_FWDDIVB_3 |  \
+			       PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
+
+#define PLLMR0_DEFAULT		PLLMR0_333_111_55_37
+#define PLLMR1_DEFAULT		PLLMR1_333_111_55_37
+#define PLLMR0_DEFAULT_PCI66	PLLMR0_333_111_55_111
+#define PLLMR1_DEFAULT_PCI66	PLLMR1_333_111_55_111
+
+#endif
+/*----------------------------------------------------------------------------*/
+
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars */
+
+#define CONFIG_ENV_OVERWRITE 1
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"bootfile=/tftpboot/taihu/uImage\0"				\
+	"rootpath=/opt/eldk/ppc_4xx\0"					\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
+	        "bootm\0"						\
+	"kernel_addr=FC000000\0"					\
+	"ramdisk_addr=FC180000\0"					\
+	"load=tftp 200000 /tftpboot/taihu/u-boot.bin\0"			\
+	"update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;"	\
+		"cp.b 200000 FFFC0000 40000\0"				\
+	"upd=run load;run update\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0x14	/* PHY address			*/
+#define CONFIG_HAS_ETH1
+#define CONFIG_PHY1_ADDR	0x10	/* EMAC1 PHY address		*/
+#define CONFIG_NET_MULTI	1
+#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
+#define CONFIG_PHY_RESET	1
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SPI
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+#undef CONFIG_SPD_EEPROM		/* use SPD EEPROM for setup */
+#define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */
+#define CFG_SDRAM_BANKS	        2
+
+/*
+ * SDRAM configuration (please see cpu/ppc/sdram.[ch])
+ */
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK1	1	/* init onboard SDRAM bank 1 */
+
+/* SDRAM timings used in datasheet */
+#define CFG_SDRAM_CL            3	/* CAS latency */
+#define CFG_SDRAM_tRP           20	/* PRECHARGE command period */
+#define CFG_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE command period */
+#define CFG_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
+#define CFG_SDRAM_tRFC		66	/* Auto refresh period */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START  0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END	   0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+/*
+ * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * The Linux BASE_BAUD define should match this configuration.
+ *    baseBaud = cpuClock/(uartDivisor*16)
+ * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * set Linux BASE_BAUD to 403200.
+ */
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#undef  CFG_EXT_SERIAL_CLOCK           /* external serial clock */
+#undef  CFG_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
+#define CFG_BASE_BAUD		691200
+
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_UART1_CONSOLE	1
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE  \
+    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+#define CFG_LOAD_ADDR	    0x100000	/* default load address */
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * I2C stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef  CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_NOPROBES	{ 0x69 } /* avoid iprobe hangup (why?) */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6 /* 24C02 requires 5ms delay */
+
+#define CFG_I2C_EEPROM_ADDR	0x50	/* I2C boot EEPROM (24C02W)	*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+
+#define CONFIG_SOFT_SPI
+#define SPI_SCL  spi_scl
+#define SPI_SDA  spi_sda
+#define SPI_READ spi_read()
+#define SPI_DELAY udelay(2)
+#ifndef __ASSEMBLY__
+void spi_scl(int);
+void spi_sda(int);
+unsigned char spi_read(void);
+#endif
+
+/* standard dtt sensor configuration */
+#define CONFIG_DTT_DS1775	1
+#define CONFIG_DTT_SENSORS	{ 0 }
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter    */
+#define PCI_HOST_FORCE   1		/* configure as pci host       */
+#define PCI_HOST_AUTO    2		/* detected via arbiter enable */
+
+#define CONFIG_PCI			/* include pci support	       */
+#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function    */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play        */
+					/* resource configuration      */
+#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
+#define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
+#define CFG_PCI_CLASSCODE       0x0600  /* PCI Class Code: bridge/host */
+#define CFG_PCI_PTM1LA	    0x00000000	/* point to sdram              */
+#define CFG_PCI_PTM1MS      0x80000001	/* 2GB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI     0x00000000	/* Host: use this pci address  */
+#define CFG_PCI_PTM2LA      0x00000000	/* disabled                    */
+#define CFG_PCI_PTM2MS	    0x00000000	/* disabled                    */
+#define CFG_PCI_PTM2PCI     0x04000000	/* Host: use this pci address  */
+#define CONFIG_EEPRO100		1
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFE00000
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_ADDR0         0x555
+#define CFG_FLASH_ADDR1         0x2aa
+#define CFG_FLASH_WORD_SIZE     unsigned short
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x10000	/* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif /* CFG_ENV_IS_IN_FLASH */
+
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_NVRAM_BASE_ADDR	0xf0000000	/* NVRAM base address */
+#define CFG_NVRAM_SIZE		0x1ff8		/* NVRAM size */
+
+#ifdef CFG_ENV_IS_IN_NVRAM
+#define CFG_ENV_SIZE		0x0ff8		/* Size of Environment vars */
+#define CFG_ENV_ADDR		\
+	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)	/* Env*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * PPC405 GPIO Configuration
+ */
+#define CFG_440_GPIO_TABLE { /*				GPIO	Alternate1		*/	\
+{												\
+/* GPIO Core 0 */										\
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO0	PerBLast    SPI CS	*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO1	TS1E			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO2	TS2E			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO3	TS1O			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO4	TS2O			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO5	TS3			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO6	TS4			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO7	TS5			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO8	TS6			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO9	TrcClk			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10	PerCS1			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11	PerCS2			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12	PerCS3			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13	PerCS4			*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO14	PerAddr03   SPI SCLK	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO15	PerAddr04   SPI DI	*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO16	PerAddr05   SPI DO	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17	IRQ0	    PCI INTA	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18	IRQ1	    PCI INTB	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19	IRQ2	    PCI INTC	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO20	IRQ3	    PCI INTD	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO21	IRQ4	    USB		*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO22	IRQ5	    EBC		*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO23	IRQ6	    unused	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24	UART0_DCD   UART1	*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25	UART0_DSR		*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26	UART0_RI		*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27	UART0_DTR		*/	\
+{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28	UART1_Rx    UART0 	*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29	UART1_Tx		*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO30	RejectPkt0  User LED1	*/	\
+{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO31	RejectPkt1  User LED2	*/	\
+}												\
+}
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405EP CPU */
+#define CFG_CACHELINE_SIZE	32
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM  0xFC000000	/* FLASH bank #1 */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory (OCM) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM        1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+
+#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash/SRAM) initialization */
+#define CFG_EBC_PB0AP           0x03815600
+#define CFG_EBC_PB0CR           0xFFE3A000  /* BAS=0xFFE,BS=2MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (NVRAM/RTC) initialization */
+#define CFG_EBC_PB1AP           0x05815600
+#define CFG_EBC_PB1CR           0xFC0BA000  /* BAS=0xFc0,BS=32MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 2 (USB device) initialization */
+#define CFG_EBC_PB2AP           0x03016600
+#define CFG_EBC_PB2CR           0x50018000 /* BAS=0x500,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 3 (LCM and D-flip-flop) initialization */
+#define CFG_EBC_PB3AP           0x158FF600
+#define CFG_EBC_PB3CR           0x50118000 /* BAS=0x501,BS=1MB,BU=R/W,BW=8bit */
+
+/* Memory Bank 4 (not install) initialization */
+#define CFG_EBC_PB4AP           0x158FF600
+#define CFG_EBC_PB4CR           0x5021A000
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0]     - External Bus Controller BLAST output
+ * GPIO0[1-9]   - Instruction trace outputs
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CFG_GPIO0_OSRH	0x15555550	/* output select high/low */
+#define CFG_GPIO0_OSRL	0x00000110
+#define CFG_GPIO0_ISR1H	0x00000001	/* input select high/low */
+#define CFG_GPIO0_ISR1L	0x15545440
+#define CFG_GPIO0_TSRH	0x00000000	/* three-state select high/low */
+#define CFG_GPIO0_TSRL	0x00000000
+#define CFG_GPIO0_TCR	0xFFFE8117	/* three-state control */
+#define CFG_GPIO0_ODR	0x00000000	/* open drain */
+
+#define GPIO0		0		/* GPIO controller 0 */
+
+/* the GPIO macros in include/ppc405.h for High/Low registers are backwards */
+
+#define GPIOx_OSL	(GPIO0_OSRH-GPIO_BASE)
+#define GPIOx_TSL	(GPIO0_TSRH-GPIO_BASE)
+#define GPIOx_IS1L	(GPIO0_ISR1H-GPIO_BASE)
+#define GPIOx_IS2L	(GPIO0_ISR1H-GPIO_BASE)
+#define GPIOx_IS3L	(GPIO0_ISR1H-GPIO_BASE)
+
+#define GPIO_OS(x)	(x+GPIOx_OSL)	/* GPIO output select */
+#define GPIO_TS(x)	(x+GPIOx_TSL)	/* GPIO three-state select */
+#define GPIO_IS1(x)	(x+GPIOx_IS1L)	/* GPIO input select */
+#define GPIO_IS2(x)	(x+GPIOx_IS1L)
+#define GPIO_IS3(x)	(x+GPIOx_IS1L)
+
+#define CPLD_REG0_ADDR	0x50100000
+#define CPLD_REG1_ADDR	0x50100001
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/trab.h b/include/configs/trab.h
index dbccea2..b9088a8 100644
--- a/include/configs/trab.h
+++ b/include/configs/trab.h
@@ -419,6 +419,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_ADDR+CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /* Initial value of the on-board touch screen brightness */
 #define CFG_BRIGHTNESS 0x20
 
diff --git a/include/configs/trizepsiv.h b/include/configs/trizepsiv.h
new file mode 100644
index 0000000..84998d4
--- /dev/null
+++ b/include/configs/trizepsiv.h
@@ -0,0 +1,325 @@
+/*
+ * (C) Copyright 2007
+ * Stefano Babic, DENX Gmbh, sbabic@denx.de
+ *
+ * (C) Copyright 2004
+ * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net
+ *
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the LUBBOCK board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_PXA27X		1	/* This is an PXA27x CPU    */
+
+#define LITTLEENDIAN		1	/* used by usb_ohci.c		*/
+
+#define CONFIG_MMC		1
+#define BOARD_LATE_INIT		1
+
+#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
+
+#define RTC
+
+/*
+ * Size of malloc() pool
+ */
+#define CFG_MALLOC_LEN	    (CFG_ENV_SIZE + 128*1024)
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_FFUART	       1       /* we use FFUART on Conxs */
+#define CONFIG_BTUART	       1       /* we use BTUART on Conxs */
+#define CONFIG_STUART	       1       /* we use STUART on Conxs */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE	       38400
+
+#define CONFIG_DOS_PARTITION   1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_IMLS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+
+#undef CONFIG_SHOW_BOOT_PROGRESS
+
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_SERVERIP		192.168.1.99
+#define CONFIG_BOOTCOMMAND	"run boot_flash"
+#define CONFIG_BOOTARGS		"console=ttyS0,38400 ramdisk_size=12288"\
+				" rw root=/dev/ram initrd=0xa0800000,5m"
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"program_boot_mmc="						\
+			"mw.b 0xa0010000 0xff 0x20000; "		\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0010000 u-boot.bin; "	\
+			"then "						\
+				"protect off 0x0 0x1ffff; "		\
+				"erase 0x0 0x1ffff; "			\
+				"cp.b 0xa0010000 0x0 0x20000; "		\
+			"fi\0"						\
+	"program_uzImage_mmc="						\
+			"mw.b 0xa0010000 0xff 0x180000; "		\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0010000 uzImage; "	\
+			"then "						\
+				"protect off 0x40000 0x1bffff; "	\
+				"erase 0x40000 0x1bffff; "		\
+				"cp.b 0xa0010000 0x40000 0x180000; "	\
+			"fi\0"						\
+	"program_ramdisk_mmc="						\
+			"mw.b 0xa0010000 0xff 0x500000; "		\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0010000 ramdisk.gz; "	\
+			"then "						\
+				"protect off 0x1c0000 0x6bffff; "	\
+				"erase 0x1c0000 0x6bffff; "		\
+				"cp.b 0xa0010000 0x1c0000 0x500000; "	\
+			"fi\0"						\
+	"boot_mmc="							\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0030000 uzImage && "	\
+				"fatload mmc 0 0xa0800000 ramdisk.gz; "	\
+			"then "						\
+				"bootm 0xa0030000; "			\
+			"fi\0"						\
+	"boot_flash="							\
+			"cp.b 0x1c0000 0xa0800000 0x500000; "		\
+			"bootm 0x40000\0"				\
+
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_CMDLINE_TAG	 1	/* enable passing of ATAGs	*/
+/* #define CONFIG_INITRD_TAG	 1 */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_HUSH_PARSER		1
+#define CFG_PROMPT_HUSH_PS2	"> "
+
+#define CFG_LONGHELP				/* undef to save memory		*/
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT		"$ "		/* Monitor Command Prompt */
+#else
+#define CFG_PROMPT		"=> "		/* Monitor Command Prompt */
+#endif
+#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_DEVICE_NULLDEV	1
+
+#define CFG_MEMTEST_START	0xa0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
+
+#undef	CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR		0xa1000000	/* default load address */
+
+#define CFG_HZ			3686400		/* incrementer freq: 3.6864 MHz */
+#define CFG_CPUSPEED		0x207		/* need to look more closely, I think this is Turbo = 2x, L=91Mhz */
+
+						/* valid baudrates */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_MMC_BASE		0xF0000000
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
+#endif
+
+/*
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS	4	   /* we have 2 banks of DRAM */
+#define PHYS_SDRAM_1		0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE	0x04000000 /* 64 MB */
+#define PHYS_SDRAM_2		0xa4000000 /* SDRAM Bank #2 */
+#define PHYS_SDRAM_2_SIZE	0x00000000 /* 0 MB */
+#define PHYS_SDRAM_3		0xa8000000 /* SDRAM Bank #3 */
+#define PHYS_SDRAM_3_SIZE	0x00000000 /* 0 MB */
+#define PHYS_SDRAM_4		0xac000000 /* SDRAM Bank #4 */
+#define PHYS_SDRAM_4_SIZE	0x00000000 /* 0 MB */
+
+#define PHYS_FLASH_1		0x00000000 /* Flash Bank #1 */
+
+#define CFG_DRAM_BASE		0xa0000000
+#define CFG_DRAM_SIZE		0x04000000
+
+#define CFG_FLASH_BASE		PHYS_FLASH_1
+
+/*
+ * GPIO settings
+ */
+#define CFG_GPSR0_VAL		0x00018000
+#define CFG_GPSR1_VAL		0x00000000
+#define CFG_GPSR2_VAL		0x400dc000
+#define CFG_GPSR3_VAL		0x00000000
+#define CFG_GPCR0_VAL		0x00000000
+#define CFG_GPCR1_VAL		0x00000000
+#define CFG_GPCR2_VAL		0x00000000
+#define CFG_GPCR3_VAL		0x00000000
+#define CFG_GPDR0_VAL		0x00018000
+#define CFG_GPDR1_VAL		0x00028801
+#define CFG_GPDR2_VAL		0x520dc000
+#define CFG_GPDR3_VAL		0x0001E000
+#define CFG_GAFR0_L_VAL		0x801c0000
+#define CFG_GAFR0_U_VAL		0x00000013
+#define CFG_GAFR1_L_VAL		0x6990100A
+#define CFG_GAFR1_U_VAL		0x00000008
+#define CFG_GAFR2_L_VAL		0xA0000000
+#define CFG_GAFR2_U_VAL		0x010900F2
+#define CFG_GAFR3_L_VAL		0x54000003
+#define CFG_GAFR3_U_VAL		0x00002401
+#define CFG_GRER0_VAL		0x00000000
+#define CFG_GRER1_VAL		0x00000000
+#define CFG_GRER2_VAL		0x00000000
+#define CFG_GRER3_VAL		0x00000000
+#define CFG_GFER0_VAL		0x00000000
+#define CFG_GFER1_VAL		0x00000000
+#define CFG_GFER2_VAL		0x00000000
+#define CFG_GFER3_VAL		0x00000020
+
+
+#define CFG_PSSR_VAL		0x20	/* CHECK */
+
+/*
+ * Clock settings
+ */
+#define CFG_CKEN		0x01FFFFFF	/* CHECK */
+#define CFG_CCCR		0x02000290 /*   520Mhz */
+
+/*
+ * Memory settings
+ */
+
+#define CFG_MSC0_VAL		0x4df84df0
+#define CFG_MSC1_VAL		0x7ff87ff4
+#define CFG_MSC2_VAL		0xa26936d4
+#define CFG_MDCNFG_VAL		0x880009C9
+#define CFG_MDREFR_VAL		0x20ca201e
+#define CFG_MDMRS_VAL		0x00220022
+
+#define CFG_FLYCNFG_VAL		0x00000000
+#define CFG_SXCNFG_VAL		0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CFG_MECR_VAL		0x00000001
+#define CFG_MCMEM0_VAL		0x00004204
+#define CFG_MCMEM1_VAL		0x00010204
+#define CFG_MCATT0_VAL		0x00010504
+#define CFG_MCATT1_VAL		0x00010504
+#define CFG_MCIO0_VAL		0x00008407
+#define CFG_MCIO1_VAL		0x0000c108
+
+#define CONFIG_DRIVER_DM9000		1
+#define CONFIG_DRIVER_DM9000		1
+#define CONFIG_DM9000_BASE	0x08000000
+#define DM9000_IO			CONFIG_DM9000_BASE
+#define DM9000_DATA			(CONFIG_DM9000_BASE+0x8004)
+/* #define CONFIG_DM9000_USE_8BIT */
+/* #define CONFIG_DM9000_USE_16BIT */
+#define CONFIG_DM9000_USE_32BIT
+
+#define CONFIG_USB_OHCI_NEW	1
+#define CFG_USB_OHCI_BOARD_INIT	1
+#define CFG_USB_OHCI_MAX_ROOT_PORTS	3
+#define CFG_USB_OHCI_REGS_BASE	0x4C000000
+#define CFG_USB_OHCI_SLOT_NAME	"trizepsiv"
+#define CONFIG_USB_STORAGE	1
+#define CFG_USB_OHCI_CPU_INIT	1
+
+/*
+ * FLASH and environment organization
+ */
+
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER	1
+
+#define CFG_MONITOR_BASE	0
+#define CFG_MONITOR_LEN		0x40000
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	4 + 255  /* max number of sectors on one chip    */
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT	(25*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT	(25*CFG_HZ) /* Timeout for Flash Write */
+
+/* write flash less slowly */
+#define CFG_FLASH_USE_BUFFER_WRITE 1
+
+/* Flash environment locations */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(PHYS_FLASH_1 + CFG_MONITOR_LEN)	/* Addr of Environment Sector	*/
+#define CFG_ENV_SIZE		0x40000	/* Total Size of Environment     	*/
+#define CFG_ENV_SECT_SIZE	0x40000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR+CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/uc101.h b/include/configs/uc101.h
index 3b471d0..aed80ec 100644
--- a/include/configs/uc101.h
+++ b/include/configs/uc101.h
@@ -332,7 +332,6 @@
 #define CFG_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
 
 #define CONFIG_IDE_PREINIT	1
-/* #define CONFIG_IDE_RESET	1 beispile siehe tqm5200.c */
 
 #define CFG_ATA_IDE0_OFFSET	0x0000
 
diff --git a/include/configs/virtlab2.h b/include/configs/virtlab2.h
index 561a8bc..edae6f4 100644
--- a/include/configs/virtlab2.h
+++ b/include/configs/virtlab2.h
@@ -207,6 +207,8 @@
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 
+#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+
 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 9c536fd..74033b4 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -46,7 +46,6 @@
 #define EXTCLK_83		83333333
 
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 #undef  CONFIG_STRESS
 
@@ -69,11 +68,11 @@
 #define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */
 
 #define CFG_PCIE0_CFGBASE	0xc0000000
-#define CFG_PCIE0_XCFGBASE	0xc0000400
-#define CFG_PCIE1_CFGBASE	0xc0001000
-#define CFG_PCIE1_XCFGBASE	0xc0001400
-#define CFG_PCIE2_CFGBASE	0xc0002000
-#define CFG_PCIE2_XCFGBASE	0xc0002400
+#define CFG_PCIE1_CFGBASE	0xc1000000
+#define CFG_PCIE2_CFGBASE	0xc2000000
+#define CFG_PCIE0_XCFGBASE	0xc3000000
+#define CFG_PCIE1_XCFGBASE	0xc3001000
+#define CFG_PCIE2_XCFGBASE	0xc3002000
 
 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
@@ -183,6 +182,7 @@
 		"cp.b ${fileaddr} FFFB0000 ${filesize};"		\
 		"setenv filesize;saveenv\0"				\
 	"upd=run load;run update\0"					\
+	"pciconfighost=1\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -298,7 +298,7 @@
 #define CONFIG_PCI			/* include pci support		*/
 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
-#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE
 
 /* Board-specific PCI */
 #define CFG_PCI_TARGET_INIT		/* let board init pci target    */
diff --git a/include/configs/zeus.h b/include/configs/zeus.h
new file mode 100644
index 0000000..605755a
--- /dev/null
+++ b/include/configs/zeus.h
@@ -0,0 +1,382 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * zeus.h - configuration for Zeus board
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_ZEUS		1		/* Board is Zeus	*/
+#define CONFIG_4xx		1		/* ... PPC4xx family	*/
+#define CONFIG_405EP		1		/* Specifc 405EP support*/
+
+#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
+
+#define PLLMR0_DEFAULT		PLLMR0_333_111_55_111
+#define PLLMR1_DEFAULT		PLLMR1_333_111_55_111
+
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+
+#define CONFIG_OVERWRITE_ETHADDR_ONCE	1
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0x01	/* PHY address			*/
+#define CONFIG_HAS_ETH1		1
+#define CONFIG_PHY1_ADDR	0x11	/* EMAC1 PHY address		*/
+#define CONFIG_NET_MULTI	1
+#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
+#define CONFIG_PHY_RESET	1
+#define CONFIG_PHY_RESET_DELAY	300	/* PHY RESET recovery delay	*/
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_LOG
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+/* POST support */
+#define CONFIG_POST		(CFG_POST_MEMORY   | \
+				 CFG_POST_CPU	   | \
+				 CFG_POST_CACHE	   | \
+				 CFG_POST_UART	   | \
+				 CFG_POST_ETHER)
+
+#define CFG_POST_ETHER_EXT_LOOPBACK	/* eth POST using ext loopack connector	*/
+
+/* Define here the base-addresses of the UARTs to test in POST */
+#define CFG_POST_UART_TABLE	{UART0_BASE}
+
+#define CONFIG_LOGBUFFER
+#define CFG_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/
+
+#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*-----------------------------------------------------------------------
+ * SDRAM
+ *----------------------------------------------------------------------*/
+/*
+ * SDRAM configuration (please see cpu/ppc/sdram.[ch])
+ */
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */
+#define CONFIG_SDRAM_BANK1	1	/* init onboard SDRAM bank 1 */
+
+/* SDRAM timings used in datasheet */
+#define CFG_SDRAM_CL            3	/* CAS latency */
+#define CFG_SDRAM_tRP           20	/* PRECHARGE command period */
+#define CFG_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE command period */
+#define CFG_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
+#define CFG_SDRAM_tRFC		66	/* Auto refresh period */
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef	CFG_EXT_SERIAL_CLOCK			/* external serial clock */
+#define CFG_BASE_BAUD		691200
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+/* these are for the ST M24C02 2kbit serial i2c eeprom */
+#define CFG_I2C_EEPROM_ADDR	0x50		/* base address */
+#define CFG_I2C_EEPROM_ADDR_LEN	1		/* bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+
+#define CFG_EEPROM_PAGE_WRITE_ENABLE	1	/* write eeprom in pages */
+#define CFG_EEPROM_PAGE_WRITE_BITS	3	/* 8 byte write page size */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
+
+/*
+ * The layout of the I2C EEPROM, used for bootstrap setup and for board-
+ * specific values, like ethaddr... that can be restored via the sw-reset
+ * button
+ */
+#define FACTORY_RESET_I2C_EEPROM	0x50
+#define FACTORY_RESET_ENV_OFFS		0x80
+#define FACTORY_RESET_ENV_SIZE		0x80
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFF000000
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI				/* The flash is CFI compatible	*/
+#define CFG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/
+
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CFG_FLASH_PROTECTION	1	/* use hardware flash protection	*/
+
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x20000	/* size of one complete sector		*/
+#define CFG_ENV_ADDR		((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405EP CPU			*/
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory (OCM) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM	1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of OCM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+
+#define CFG_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+/* reserve some memory for POST and BOOT limit info */
+#define CFG_INIT_SP_OFFSET	(CFG_GBL_DATA_OFFSET - 16)
+
+/* extra data in OCM */
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 4)
+#define CFG_POST_MAGIC		(CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 8)
+#define CFG_POST_VAL		(CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 12)
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash 16M) initialization					*/
+#define CFG_EBC_PB0AP		0x05815600
+#define CFG_EBC_PB0CR		0xFF09A000  /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit  */
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0]     - External Bus Controller BLAST output
+ * GPIO0[1-9]   - Instruction trace outputs
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CFG_GPIO0_OSRH		0x15555550	/* Chip selects */
+#define CFG_GPIO0_OSRL		0x00000110	/* UART_DTR-pin 27 alt out */
+#define CFG_GPIO0_ISR1H		0x10000041	/* Pin 2, 12 is input */
+#define CFG_GPIO0_ISR1L		0x15505440	/* OUT: LEDs 22/23; IN: pin12,2, NVALID# */
+#define CFG_GPIO0_TSRH		0x00000000
+#define CFG_GPIO0_TSRL		0x00000000
+#define CFG_GPIO0_TCR		0xBFF68317	/* 3-state OUT: 22/23/29; 12,2 is not 3-state */
+#define CFG_GPIO0_ODR		0x00000000
+
+#define CFG_GPIO_SW_RESET	1
+#define CFG_GPIO_ZEUS_PE	12
+#define CFG_GPIO_LED_RED	22
+#define CFG_GPIO_LED_GREEN	23
+
+/* Time in milli-seconds */
+#define CFG_TIME_POST		5000
+#define CFG_TIME_FACTORY_RESET	10000
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM		0x02		/* Software reboot			*/
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
+#endif
+
+/* ENVIRONMENT VARS */
+
+#define CONFIG_PREBOOT		"echo;echo Welcome to Bulletendpoints board v1.1;echo"
+#define CONFIG_IPADDR		192.168.1.10
+#define CONFIG_SERVERIP		192.168.1.100
+#define CONFIG_GATEWAYIP	192.168.1.100
+#define CONFIG_ETHADDR		50:00:00:00:06:00
+#define CONFIG_ETH1ADDR		50:00:00:00:06:01
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled        */
+#else
+#define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"logversion=2\0"                                                \
+	"hostname=zeus\0"						\
+	"netdev=eth0\0"							\
+	"ethact=ppc_4xx_eth0\0"						\
+	"netmask=255.255.255.0\0"					\
+	"ramdisk_size=50000\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw"			\
+		" nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw"			\
+		" ramdisk=${ramdisk_size}\0"				\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+	        ":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,"		\
+		"${baudrate}\0"						\
+	"net_nfs=tftp ${kernel_mem_addr} ${file_kernel};"		\
+		"run nfsargs addip addtty;bootm\0"			\
+	"net_ram=tftp ${kernel_mem_addr} ${file_kernel};"		\
+		"tftp ${ramdisk_mem_addr} ${file_fs};"			\
+		"run ramargs addip addtty;"				\
+		"bootm ${kernel_mem_addr} ${ramdisk_mem_addr}\0"	\
+	"rootpath=/target_fs/zeus\0"					\
+	"kernel_fl_addr=ff000000\0"					\
+	"kernel_mem_addr=200000\0"					\
+	"ramdisk_fl_addr=ff300000\0"					\
+	"ramdisk_mem_addr=4000000\0"					\
+	"uboot_fl_addr=fffc0000\0"					\
+	"uboot_mem_addr=100000\0"					\
+	"file_uboot=/zeus/u-boot.bin\0"					\
+	"tftp_uboot=tftp 100000 ${file_uboot}\0"			\
+	"update_uboot=protect off fffc0000 ffffffff;"			\
+		"era fffc0000 ffffffff;cp.b 100000 fffc0000 40000;"	\
+		"protect on fffc0000 ffffffff\0"			\
+	"upd_uboot=run tftp_uboot;run update_uboot\0"			\
+	"file_kernel=/zeus/uImage_ba\0"					\
+	"tftp_kernel=tftp 100000 ${file_kernel}\0"			\
+	"update_kernel=protect off ff000000 ff17ffff;"			\
+		"era ff000000 ff17ffff;cp.b 100000 ff000000 180000\0"	\
+	"upd_kernel=run tftp_kernel;run update_kernel\0"		\
+	"file_fs=/zeus/rootfs_ba.img\0"					\
+	"tftp_fs=tftp 100000 ${file_fs}\0"				\
+	"update_fs=protect off ff300000 ff87ffff;era ff300000 ff87ffff;"\
+	        "cp.b 100000 ff300000 580000\0"				\
+	"upd_fs=run tftp_fs;run update_fs\0"				\
+	"bootcmd=chkreset;run ramargs addip addtty addmisc;"		\
+		"bootm ${kernel_fl_addr} ${ramdisk_fl_addr}\0"		\
+	""
+
+#endif	/* __CONFIG_H */