Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

6 files changed, 766 insertions, 7 deletions

diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index 2aba689..6f1b1a4 100644
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -404,7 +404,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /* controller 3, direct to uli, tgtid 3, Base address 8000 */
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
 #ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc00000000ull
 #else
 #define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
@@ -423,7 +423,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /* controller 2, Slot 2, tgtid 2, Base address 9000 */
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
 #else
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
@@ -442,7 +442,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /* controller 1, Slot 1, tgtid 1, Base address a000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
 #ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc40000000ull
 #else
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index d8042fb..035874b 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -335,7 +335,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_SYS_PCI1_MEM_VIRT	0x80000000
 #ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCI1_MEM_BUS		0xc0000000
+#define CONFIG_SYS_PCI1_MEM_BUS		0xe0000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	0x0000000c00000000ULL
 #else
 #define CONFIG_SYS_PCI1_MEM_BUS		CONFIG_SYS_PCI1_MEM_VIRT
diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
index a39ff26..fddcce5 100644
--- a/include/configs/P2020DS.h
+++ b/include/configs/P2020DS.h
@@ -46,6 +46,7 @@
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+#define CONFIG_E1000		1	/* Defind e1000 pci Ethernet card*/
 
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
@@ -437,7 +438,7 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy);
 /* controller 3, Slot 1, tgtid 3, Base address b000 */
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
 #ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc00000000ull
 #else
 #define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
@@ -456,7 +457,7 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy);
 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
 #else
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
@@ -475,7 +476,7 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy);
 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
 #ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc40000000ull
 #else
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index 3f943aa..4b9bcca 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -96,6 +96,7 @@
 #undef CONFIG_DDR_SPD
 #define CONFIG_DDR_DLL                      /* possible DLL fix needed */
 #define CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#define CONFIG_FSL_DMA			    /* use DMA to init DDR ECC  */
 
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
index 43c2873..1db20bc 100644
--- a/include/configs/PM856.h
+++ b/include/configs/PM856.h
@@ -98,6 +98,7 @@
 #undef CONFIG_DDR_SPD
 #define CONFIG_DDR_DLL                      /* possible DLL fix needed */
 #define CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#define CONFIG_FSL_DMA			    /* use DMA to init DDR ECC  */
 
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
diff --git a/include/configs/XPEDITE5170.h b/include/configs/XPEDITE5170.h
new file mode 100644
index 0000000..2553293
--- /dev/null
+++ b/include/configs/XPEDITE5170.h
@@ -0,0 +1,756 @@
+/*
+ * Copyright 2009 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * xpedite5170 board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC86xx		1	/* MPC86xx */
+#define CONFIG_MPC8641		1	/* MPC8641 specific */
+#define CONFIG_XPEDITE5140	1	/* MPC8641HPCN board specific */
+#define CONFIG_SYS_BOARD_NAME	"XPedite5170"
+#define CONFIG_NUM_CPUS		1	/* Number of CPUs in the system */
+#define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
+#define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
+#define CONFIG_RELOC_FIXUP_WORKS	/* Fully relocate to SDRAM */
+#define CONFIG_HIGH_BATS	1	/* High BATs supported and enabled */
+#define CONFIG_ALTIVEC		1
+
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#define CONFIG_PCI_PNP		1	/* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
+#define CONFIG_PCIE1		1	/* PCIE controler 1 */
+#define CONFIG_PCIE2		1	/* PCIE controler 2 */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+
+/*
+ * DDR config
+ */
+#define CONFIG_FSL_DDR2
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#define SPD_EEPROM_ADDRESS1		0x54	/* Both channels use the */
+#define SPD_EEPROM_ADDRESS2		0x54	/* same SPD data         */
+#define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
+#define CONFIG_NUM_DDR_CONTROLLERS	2
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	1
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
+
+/*
+ * virtual address to be used for temporary mappings.  There
+ * should be 128k free at this VA.
+ */
+#define CONFIG_SYS_SCRATCH_VA	0xe0000000
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC86xx */
+
+/*
+ * L2CR setup
+ */
+#define CONFIG_SYS_L2
+#define L2_INIT		0
+#define L2_ENABLE	(L2CR_L2E)
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xef000000	/* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
+#define CONFIG_SYS_IMMR			CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_PCIE1_ADDR		(CONFIG_SYS_CCSRBAR + 0x8000)
+#define CONFIG_SYS_PCIE2_ADDR		(CONFIG_SYS_CCSRBAR + 0x9000)
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x10000000
+#define CONFIG_SYS_MEMTEST_END		0x20000000
+
+/*
+ * Memory map
+ * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+ * 0x8000_0000	0xbfff_ffff	PCIe1 Mem		1G non-cacheable
+ * 0xc000_0000	0xcfff_ffff	PCIe2 Mem		256M non-cacheable
+ * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
+ * 0xe800_0000	0xe87f_ffff	PCIe1 IO		8M non-cacheable
+ * 0xe880_0000	0xe8ff_ffff	PCIe2 IO		8M non-cacheable
+ * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
+ * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
+ * 0xf000_0000	0xf7ff_ffff	NOR Flash 2		128M non-cacheable
+ * 0xf800_0000	0xffff_ffff	NOR Flash 1		128M non-cacheable
+ */
+
+#define CONFIG_SYS_LBC_LCRR		(LCRR_CLKDIV_2 | LCRR_EADC_3)
+
+/*
+ * NAND flash configuration
+ */
+#define CONFIG_SYS_NAND_BASE		0xef800000
+#define CONFIG_SYS_NAND_BASE2		0xef840000	/* Unused at this time */
+#define CONFIG_SYS_NAND_BASE_LIST 	{CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
+#define CONFIG_SYS_MAX_NAND_DEVICE	2
+#define CONFIG_NAND_ACTL
+#define CONFIG_SYS_NAND_ACTL_ALE 	(1 << 14)	/* C_LA14 */
+#define CONFIG_SYS_NAND_ACTL_CLE 	(1 << 15)	/* C_LA15 */
+#define CONFIG_SYS_NAND_ACTL_NCE	0		/* NCE not controlled by ADDR */
+#define CONFIG_SYS_NAND_ACTL_DELAY	25
+#define CONFIG_SYS_NAND_QUIET_TEST
+#define CONFIG_JFFS2_NAND
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE		0xf8000000
+#define CONFIG_SYS_FLASH_BASE2		0xf0000000
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff00000, 0xc0000}, \
+						  {0xf7f00000, 0xc0000} }
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE_EARLY	0xfff00000	/* early monitor loc */
+
+/*
+ * Chip select configuration
+ */
+/* NOR Flash 0 on CS0 */
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	|\
+				 BR_PS_16		|\
+				 BR_V)
+#define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		|\
+				 OR_GPCM_CSNT		|\
+				 OR_GPCM_XACS		|\
+				 OR_GPCM_ACS_DIV2	|\
+				 OR_GPCM_SCY_8		|\
+				 OR_GPCM_TRLX		|\
+				 OR_GPCM_EHTR		|\
+				 OR_GPCM_EAD)
+
+/* NOR Flash 1 on CS1 */
+#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	|\
+				 BR_PS_16		|\
+				 BR_V)
+#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	|\
+				 BR_PS_8		|\
+				 BR_V)
+#define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB		|\
+				 OR_GPCM_BCTLD		|\
+				 OR_GPCM_CSNT		|\
+				 OR_GPCM_ACS_DIV4	|\
+				 OR_GPCM_SCY_4		|\
+				 OR_GPCM_TRLX		|\
+				 OR_GPCM_EHTR)
+
+/* Optional NAND flash on CS3 */
+#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	|\
+				 BR_PS_8		|\
+				 BR_V)
+#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
+
+/*
+ * Use L1 as initial stack
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
+#define CONFIG_SYS_INIT_RAM_END		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+#define CONFIG_SYS_64BIT_VSPRINTF	1
+#define CONFIG_SYS_64BIT_STRTOUL	1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C				/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C				/* I2C with hardware support */
+#define CONFIG_SYS_I2C_SPEED		100000	/* M41T00 only supports 100 KHz */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+
+/* PEX8518 slave I2C interface */
+#define CONFIG_SYS_I2C_PEX8518_ADDR	0x70
+
+/* I2C DS1631 temperature sensor */
+#define CONFIG_SYS_I2C_DS1621_ADDR	0x48
+#define CONFIG_DTT_DS1621
+#define CONFIG_DTT_SENSORS		{ 0 }
+
+/* I2C EEPROM - AT24C128B */
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11		1
+#define CONFIG_SYS_I2C_RTC_ADDR		0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR	2000
+
+/* GPIO/EEPROM/SRAM */
+#define CONFIG_DS4510
+#define CONFIG_SYS_I2C_DS4510_ADDR	0x51
+
+/* GPIO */
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
+#define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
+#define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
+#define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
+#define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
+
+/*
+ * PU = pulled high, PD = pulled low
+ * I = input, O = output, IO = input/output
+ */
+/* PCA9557 @ 0x18*/
+#define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select */
+#define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select */
+#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
+#define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Set to 0 to enable NVM writing */
+
+/* PCA9557 @ 0x1c*/
+#define CONFIG_SYS_PCA953X_XMC0_ROOT0		0x01 /* PU; Low if XMC is RC */
+#define CONFIG_SYS_PCA953X_PLUG_GPIO0		0x02 /* Samtec connector GPIO */
+#define CONFIG_SYS_PCA953X_XMC0_WAKE		0x04 /* PU; XMC wake */
+#define CONFIG_SYS_PCA953X_XMC0_BIST		0x08 /* PU; XMC built in self test */
+#define CONFIG_SYS_PCA953X_XMC_PRESENT		0x10 /* PU; Low if XMC module installed */
+#define CONFIG_SYS_PCA953X_PMC_PRESENT		0x20 /* PU; Low if PMC module installed */
+#define CONFIG_SYS_PCA953X_PMC0_MONARCH		0x40 /* PMC monarch mode enable */
+#define CONFIG_SYS_PCA953X_PMC0_EREADY		0x80 /* PU; PMC PCI eready */
+
+/* PCA9557 @ 0x1e*/
+#define CONFIG_SYS_PCA953X_P0_GA0		0x01 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA1		0x02 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA2		0x04 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA3		0x08 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA4		0x10 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GAP		0x20 /* PU; VPX Geographical address parity */
+#define CONFIG_SYS_PCA953X_P1_SYSEN		0x80 /* PU; VPX P1 SYSCON */
+
+/* PCA9557 @ 0x1f */
+#define CONFIG_SYS_PCA953X_VPX_GPIO0		0x01 /* PU; VPX P15 GPIO */
+#define CONFIG_SYS_PCA953X_VPX_GPIO1		0x02 /* PU; VPX P15 GPIO */
+#define CONFIG_SYS_PCA953X_VPX_GPIO2		0x04 /* PU; VPX P15 GPIO */
+#define CONFIG_SYS_PCA953X_VPX_GPIO3		0x08 /* PU; VPX P15 GPIO */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+/* PCIE1 - PEX8518 */
+#define CONFIG_SYS_PCIE1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
+
+/* PCIE2 - VPX P1 */
+#define CONFIG_SYS_PCIE2_MEM_BASE	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
+
+/*
+ * Networking options
+ */
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CONFIG_NET_MULTI	1
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_TSEC1		1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define CONFIG_HAS_ETH0
+
+#define CONFIG_TSEC2		1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_PHY_ADDR		2
+#define TSEC2_PHYIDX		0
+#define CONFIG_HAS_ETH1
+
+/*
+ * BAT mappings
+ */
+#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATL	(CONFIG_SYS_CCSRBAR_DEFAULT	|\
+					 BATL_PP_RW			|\
+					 BATL_CACHEINHIBIT		|\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATU	(CONFIG_SYS_CCSRBAR_DEFAULT	|\
+					 BATU_BL_1M			|\
+					 BATU_VS			|\
+					 BATU_VP)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATL	(CONFIG_SYS_CCSRBAR_DEFAULT	|\
+					 BATL_PP_RW			|\
+					 BATL_CACHEINHIBIT)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATU	CONFIG_SYS_CCSR_DEFAULT_DBATU
+#endif
+
+/*
+ * BAT0		2G	Cacheable, non-guarded
+ * 0x0000_0000	2G	DDR
+ */
+#define CONFIG_SYS_DBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT0U	(BATU_BL_2G | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	CONFIG_SYS_DBAT0U
+
+/*
+ * BAT1		1G	Cache-inhibited, guarded
+ * 0x8000_0000	1G	PCI-Express 1 Memory
+ */
+#define CONFIG_SYS_DBAT1L	(CONFIG_SYS_PCIE1_MEM_PHYS	|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT		|\
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT1U	(CONFIG_SYS_PCIE1_MEM_PHYS	|\
+				 BATU_BL_1G			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCIE1_MEM_PHYS	|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT1U	CONFIG_SYS_DBAT1U
+
+/*
+ * BAT2		512M	Cache-inhibited, guarded
+ * 0xc000_0000	512M	PCI-Express 2 Memory
+ */
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PCIE2_MEM_PHYS	|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT		|\
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	(CONFIG_SYS_PCIE2_MEM_PHYS	|\
+				 BATU_BL_512M			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCIE2_MEM_PHYS	|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
+
+/*
+ * BAT3		1M	Cache-inhibited, guarded
+ * 0xe000_0000	1M	CCSR
+ */
+#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_CCSRBAR		|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT		|\
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR		|\
+				 BATU_BL_1M			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR		|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U
+
+/*
+ * BAT4		32M	Cache-inhibited, guarded
+ * 0xe200_0000	16M	PCI-Express 1 I/O
+ * 0xe300_0000	16M	PCI-Express 2 I/0
+ */
+#define CONFIG_SYS_DBAT4L	(CONFIG_SYS_PCIE1_IO_PHYS	|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT		|\
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCIE1_IO_PHYS	|\
+				 BATU_BL_32M			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCIE1_IO_PHYS	|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U
+
+/*
+ * BAT5		128K	Cacheable, non-guarded
+ * 0xe400_1000	128K	Init RAM for stack in the CPU DCache (no backing memory)
+ */
+#define CONFIG_SYS_DBAT5L	(CONFIG_SYS_INIT_RAM_ADDR	|\
+				 BATL_PP_RW			|\
+				 BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT5U	(CONFIG_SYS_INIT_RAM_ADDR	|\
+				 BATU_BL_128K			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT5L	CONFIG_SYS_DBAT5L
+#define CONFIG_SYS_IBAT5U	CONFIG_SYS_DBAT5U
+
+/*
+ * BAT6		256M	Cache-inhibited, guarded
+ * 0xf000_0000	256M	FLASH
+ */
+#define CONFIG_SYS_DBAT6L	(CONFIG_SYS_FLASH_BASE2		|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT		|\
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U	(CONFIG_SYS_FLASH_BASE		|\
+				 BATU_BL_256M			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_FLASH_BASE		|\
+				 BATL_PP_RW			|\
+				 BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
+
+/* Map the last 1M of flash where we're running from reset */
+#define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY	|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT		|\
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U_EARLY	(TEXT_BASE			|\
+				 BATU_BL_1M			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY	|\
+				 BATL_PP_RW			|\
+				 BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY
+
+/*
+ * BAT7		64M	Cache-inhibited, guarded
+ * 0xe800_0000	64K	NAND FLASH
+ * 0xe804_0000	128K	DUART Registers
+ */
+#define CONFIG_SYS_DBAT7L	(CONFIG_SYS_NAND_BASE		|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT		|\
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT7U 	(CONFIG_SYS_NAND_BASE		|\
+				 BATU_BL_512K			|\
+				 BATU_VS			|\
+				 BATU_VP)
+#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_NAND_BASE		|\
+				 BATL_PP_RW			|\
+				 BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT7U	CONFIG_SYS_DBAT7U
+
+/*
+ * Command configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DS4510
+#define CONFIG_CMD_DS4510_INFO
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_CMDLINE_EDITING	1		/* Command-line editing */
+#define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG			/* do not reset board on panic */
+#define CONFIG_PREBOOT				/* enable preboot variable */
+#define CONFIG_FIT		1
+#define CONFIG_FIT_VERBOSE	1
+#define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
+
+/*
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM		0x02		/* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE		0x8000
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+
+/*
+ * Flash memory map:
+ * fffc0000 - ffffffff	Pri FDT (256KB)
+ * fff80000 - fffbffff	Pri U-Boot Environment (256 KB)
+ * fff00000 - fff7ffff	Pri U-Boot (512 KB)
+ * fef00000 - ffefffff	Pri OS image (16MB)
+ * f8000000 - feefffff	Pri OS Use/Filesystem (111MB)
+ *
+ * f7fc0000 - f7ffffff	Sec FDT (256KB)
+ * f7f80000 - f7fbffff	Sec U-Boot Environment (256 KB)
+ * f7f00000 - f7f7ffff	Sec U-Boot (512 KB)
+ * f6f00000 - f7efffff	Sec OS image (16MB)
+ * f0000000 - f6efffff	Sec OS Use/Filesystem (111MB)
+ */
+#define CONFIG_UBOOT1_ENV_ADDR	MK_STR(0xfff00000)
+#define CONFIG_UBOOT2_ENV_ADDR	MK_STR(0xf7f00000)
+#define CONFIG_FDT1_ENV_ADDR	MK_STR(0xfffc0000)
+#define CONFIG_FDT2_ENV_ADDR	MK_STR(0xf7fc0000)
+#define CONFIG_OS1_ENV_ADDR	MK_STR(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR	MK_STR(0xf6f00000)
+
+#define CONFIG_PROG_UBOOT1						\
+	"$download_cmd $loadaddr $ubootfile; "				\
+	"if test $? -eq 0; then "					\
+		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
+		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
+		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
+		"if test $? -ne 0; then "				\
+			"echo PROGRAM FAILED; "				\
+		"else; "						\
+			"echo PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_UBOOT2						\
+	"$download_cmd $loadaddr $ubootfile; "				\
+	"if test $? -eq 0; then "					\
+		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
+		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
+		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
+		"if test $? -ne 0; then "				\
+			"echo PROGRAM FAILED; "				\
+		"else; "						\
+			"echo PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_BOOT_OS_NET						\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"if test -n $fdtaddr; then "				\
+			"$download_cmd $fdtaddr $fdtfile; "		\
+			"if test $? -eq 0; then "			\
+				"bootm $osaddr - $fdtaddr; "		\
+			"else; "					\
+				"echo FDT DOWNLOAD FAILED; "		\
+			"fi; "						\
+		"else; "						\
+			"bootm $osaddr; "				\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_OS1							\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
+		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
+		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo OS PROGRAM FAILED; "			\
+		"else; "						\
+			"echo OS PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_OS2							\
+	"$download_cmd $osaddr $osfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
+		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
+		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo OS PROGRAM FAILED; "			\
+		"else; "						\
+			"echo OS PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo OS DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_FDT1						\
+	"$download_cmd $fdtaddr $fdtfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
+		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
+		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo FDT PROGRAM FAILED; "			\
+		"else; "						\
+			"echo FDT PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo FDT DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define CONFIG_PROG_FDT2						\
+	"$download_cmd $fdtaddr $fdtfile; "				\
+	"if test $? -eq 0; then "					\
+		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
+		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
+		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
+		"if test $? -ne 0; then "				\
+			"echo FDT PROGRAM FAILED; "			\
+		"else; "						\
+			"echo FDT PROGRAM SUCCEEDED; "			\
+		"fi; "							\
+	"else; "							\
+		"echo FDT DOWNLOAD FAILED; "				\
+	"fi;"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"autoload=yes\0"						\
+	"download_cmd=tftp\0"						\
+	"console_args=console=ttyS0,115200\0"				\
+	"root_args=root=/dev/nfs rw\0"					\
+	"misc_args=ip=on\0"						\
+	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+	"bootfile=/home/user/file\0"					\
+	"osfile=/home/user/uImage-XPedite5170\0"			\
+	"fdtfile=/home/user/xpedite5170.dtb\0"				\
+	"ubootfile=/home/user/u-boot.bin\0"				\
+	"fdtaddr=c00000\0"						\
+	"osaddr=0x1000000\0"						\
+	"loadaddr=0x1000000\0"						\
+	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
+	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
+	"prog_os1="CONFIG_PROG_OS1"\0"					\
+	"prog_os2="CONFIG_PROG_OS2"\0"					\
+	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
+	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
+	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
+	"bootcmd_flash1=run set_bootargs; "				\
+		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
+	"bootcmd_flash2=run set_bootargs; "				\
+		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
+	"bootcmd=run bootcmd_flash1\0"
+#endif	/* __CONFIG_H */