Merge with /home/wd/git/u-boot/master

8 files changed, 663 insertions, 90 deletions

diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 6020998..6b8759f 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -37,7 +37,6 @@
 #define CONFIG_TQM5200		1	/* ... on TQM5200 module */
 #undef CONFIG_TQM5200_REV100		/*  define for revision 100 modules */
 #define CONFIG_STK52XX		1	/* ... on a STK52XX base board */
-#define CONFIG_STK52XX_REV100	1	/*  define for revision 100 baseboards */
 
 #define CFG_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
 
@@ -83,7 +82,7 @@
 #define CONFIG_PCI_IO_SIZE	0x01000000
 
 #define CONFIG_NET_MULTI	1
-#define CONFIG_EEPRO100
+#define CONFIG_EEPRO100		1
 #define CFG_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X		1
 #endif	/* CONFIG_STK52XX */
@@ -192,16 +191,6 @@
 
 #undef	CONFIG_BOOTARGS
 
-#if defined (CONFIG_TQM5200_AA)
-# define CONFIG_U_BOOT_SUFFIX	"-AA\0"
-#elif defined (CONFIG_TQM5200_AB)
-# define CONFIG_U_BOOT_SUFFIX	"-AB\0"
-#elif defined (CONFIG_TQM5200_AC)
-# define CONFIG_U_BOOT_SUFFIX	"-AC\0"
-#else
-# define CONFIG_U_BOOT_SUFFIX	"\0"
-#endif
-
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
@@ -218,7 +207,7 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"bootfile=/tftpboot/tqm5200/uImage\0"				\
 	"load=tftp 200000 ${u-boot}\0"					\
-	"u-boot=/tftpboot/tqm5200/u-boot.bin"	CONFIG_U_BOOT_SUFFIX	\
+	"u-boot=/tftpboot/tqm5200/u-boot.bin\0"				\
 	"update=protect off FC000000 FC05FFFF;"				\
 		"erase FC000000 FC05FFFF;"				\
 		"cp.b 200000 FC000000 ${filesize};"			\
@@ -284,13 +273,6 @@
 #endif
 
 /* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB)
-#define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
-				CFG_I2C_SLAVE }
-#elif defined (CONFIG_TQM5200_AC)
-#define I2C_ADDR_LIST	{	CFG_I2C_SLAVE }
-#endif
-
 #if defined (CONFIG_MINIFAP)
 #undef I2C_ADDR_LIST
 #define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
@@ -493,13 +475,9 @@
  * SRAM - Do not map below 2 GB in address space, because this area is used
  * for SDRAM autosizing.
  */
-#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define CFG_CS2_START		0xE5000000
-#ifdef CONFIG_TQM5200_AB
-#define CFG_CS2_SIZE		0x80000		/* 512 kByte */
-#else  /* CONFIG_CS_AUTOCONF */
 #define CFG_CS2_SIZE		0x100000	/* 1 MByte */
-#endif
 #define CFG_CS2_CFG		0x0004D930
 #endif
 
@@ -507,8 +485,7 @@
  * Grafic controller - Do not map below 2 GB in address space, because this
  * area is used for SDRAM autosizing.
  */
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
-    defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define SM501_FB_BASE		0xE0000000
 #define CFG_CS1_START		(SM501_FB_BASE)
 #define CFG_CS1_SIZE		0x4000000	/* 64 MByte */
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index 18197f2..da6946b 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -177,6 +177,13 @@
 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
+/* PS/2 Keyboard */
+#define CONFIG_PS2KBD			/* AT-PS/2 Keyboard		*/
+#define CONFIG_PS2MULT			/* .. on PS/2 Multiplexer	*/
+#define CONFIG_PS2SERIAL	2	/* .. on DUART2			*/
+#define CONFIG_PS2MULT_DELAY	(CFG_HZ/2)	/* Initial delay	*/
+#define CONFIG_BOARD_EARLY_INIT_R	1
+
 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
 #ifdef	CFG_HUSH_PARSER
diff --git a/include/configs/cmc_pu2.h b/include/configs/cmc_pu2.h
index 46280f7..572a70f 100644
--- a/include/configs/cmc_pu2.h
+++ b/include/configs/cmc_pu2.h
@@ -108,7 +108,7 @@
 /* still about 20 kB free with this defined */
 #define CFG_LONGHELP
 
-#define CONFIG_BOOTDELAY      3
+#define CONFIG_BOOTDELAY      1
 
 #ifdef CONFIG_HARD_I2C
 #define CONFIG_COMMANDS		\
@@ -206,15 +206,6 @@ struct bd_info_ext {
 #error CONFIG_USE_IRQ not supported
 #endif
 
-#define CFG_DEVICE_NULLDEV	 1	/* enble null device		*/
-#define CONFIG_SILENT_CONSOLE	 1	/* enable silent startup	*/
-
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n"
-#define CONFIG_AUTOBOOT_STOP_STR "R"	/* default password */
-
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
-
 #define	CONFIG_EXTRA_ENV_SETTINGS	\
 	"net_nfs=tftp ${loadaddr} ${bootfile};run nfsargs addip addcons " \
 		"addmtd;bootm\0" \
diff --git a/include/configs/gth2.h b/include/configs/gth2.h
new file mode 100644
index 0000000..77d2d56
--- /dev/null
+++ b/include/configs/gth2.h
@@ -0,0 +1,195 @@
+/*
+ * (C) Copyright 2005
+ * Thomas.Lange@corelatus.se
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * This file contains the configuration parameters for the gth2 board.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MIPS32		1  /* MIPS32 CPU core	*/
+#define CONFIG_GTH2		1
+#define CONFIG_AU1X00		1  /* alchemy series cpu */
+
+#define CONFIG_AU1000		1
+
+#define CONFIG_MISC_INIT_R      1
+
+#define CONFIG_ETHADDR		DE:AD:BE:EF:01:02    /* Ethernet address */
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 1 seconds	*/
+
+#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */
+
+#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */
+
+#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */
+
+#define CONFIG_BAUDRATE		115200
+
+/* valid baudrates */
+#define CFG_BAUDRATE_TABLE	{ 115200 }
+
+/* Only interrupt boot if space is pressed */
+/* If a long serial cable is connected but */
+/* other end is dead, garbage will be read */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press space to abort autoboot in %d second\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+#define	CONFIG_TIMESTAMP		/* Print image info with timestamp */
+#define	CONFIG_BOOTARGS "panic=1"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"addmisc=setenv bootargs $(bootargs) "				\
+	        "ethaddr=$(ethaddr) \0"					\
+        "netboot=bootp;run addmisc;bootm\0"                             \
+                ""
+
+/* Boot from Compact flash partition 2 as default */
+#define CONFIG_BOOTCOMMAND	"ide reset;disk 0x81000000 0:2;run addmisc;bootm"
+
+#define CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP ) & \
+ ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \
+   CFG_CMD_MII | CFG_CMD_LOADS  | CFG_CMD_LOADB | CFG_CMD_ELF | \
+   CFG_CMD_BDI | CFG_CMD_BEDBUG | CFG_CMD_NFS | CFG_CMD_AUTOSCRIPT ))
+
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP				/* undef to save memory      */
+#define	CFG_PROMPT		"GTH2 # "	/* Monitor Command Prompt    */
+#define	CFG_CBSIZE		256		/* Console I/O Buffer Size   */
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)  /* Print Buffer Size */
+#define	CFG_MAXARGS		16		/* max number of command args*/
+
+#define CFG_MALLOC_LEN		128*1024
+
+#define CFG_BOOTPARAMS_LEN	128*1024
+
+#define CFG_MHZ			500
+
+#define CFG_HZ                  (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */
+
+#define CFG_SDRAM_BASE		0x80000000     /* Cached addr */
+
+#define	CFG_LOAD_ADDR		0x81000000     /* default load address	*/
+
+#define CFG_MEMTEST_START	0x80100000
+#define CFG_MEMTEST_END		0x83000000
+
+#define CONFIG_HW_WATCHDOG      1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	(128)	/* max number of sectors on one chip */
+
+#define PHYS_FLASH		0xbfc00000 /* Flash Bank #1 */
+
+/* The following #defines are needed to get flash environment right */
+#define	CFG_MONITOR_BASE	TEXT_BASE
+#define	CFG_MONITOR_LEN		(192 << 10)
+
+#define CFG_INIT_SP_OFFSET	0x400000
+
+/* We boot from this flash, selected with dip switch */
+#define CFG_FLASH_BASE		PHYS_FLASH
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT	(2 * CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT	(2 * CFG_HZ) /* Timeout for Flash Write */
+
+#define	CFG_ENV_IS_NOWHERE	1
+
+/* Address and size of Primary Environment Sector	*/
+#define CFG_ENV_ADDR		0xB0030000
+#define CFG_ENV_SIZE		0x10000
+
+#define CONFIG_FLASH_16BIT
+
+#define CONFIG_NR_DRAM_BANKS	2
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_MEMSIZE_IN_BYTES
+
+/*---ATA PCMCIA ------------------------------------*/
+#define CFG_PCMCIA_MEM_SIZE 0x4000000 /* Offset to slot 1 FIXME!!! */
+
+#define CFG_PCMCIA_MEM_ADDR  0x20000000
+#define CFG_PCMCIA_IO_BASE   0x28000000
+#define CFG_PCMCIA_ATTR_BASE 0x30000000
+
+#define CONFIG_PCMCIA_SLOT_A
+
+#define CONFIG_ATAPI 1
+#define CONFIG_MAC_PARTITION 1
+
+/* We run CF in "true ide" mode or a harddrive via pcmcia */
+#define CONFIG_IDE_PCMCIA 1
+
+/* We only support one slot for now */
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_ATA_IDE0_OFFSET	0
+
+#define CFG_ATA_BASE_ADDR       CFG_PCMCIA_IO_BASE
+
+/* Offset for data I/O			*/
+#define CFG_ATA_DATA_OFFSET     0
+
+/* Offset for normal register accesses  */
+#define CFG_ATA_REG_OFFSET      0
+
+/* Offset for alternate registers       */
+#define CFG_ATA_ALT_OFFSET      0x0200
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384
+#define CFG_ICACHE_SIZE		16384
+#define CFG_CACHELINE_SIZE	32
+
+#define GPIO_CACONFIG  (1<<0)
+#define GPIO_DPACONFIG (1<<6)
+#define GPIO_ERESET    (1<<11)
+#define GPIO_EEDQ      (1<<17)
+#define GPIO_WDI       (1<<18)
+#define GPIO_RJ1LY     (1<<22)
+#define GPIO_RJ1LG     (1<<23)
+#define GPIO_LEDCLK    (1<<29)
+#define GPIO_LEDD      (1<<30)
+#define GPIO_CPU_LED   (1<<31)
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h
new file mode 100644
index 0000000..ea15524
--- /dev/null
+++ b/include/configs/ppmc7xx.h
@@ -0,0 +1,419 @@
+/*
+ * ppmc7xx.h
+ * ---------
+ * 
+ * Wind River PPMC 7xx/74xx board configuration file.
+ * 
+ * By Richard Danter (richard.danter@windriver.com)
+ * Copyright (C) 2005 Wind River Systems
+ */
+
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_PPMC7XX
+
+
+/*===================================================================
+ * 
+ * User configurable settings - Modify to your preference
+ * 
+ *===================================================================
+ */
+
+/*
+ * Debug
+ * 
+ * DEBUG			- Define this is you want extra debug info
+ * GTREGREAD			- Required to build with debug
+ * do_bdinfo			- Required to build with debug
+ */
+
+#undef	DEBUG
+#define	GTREGREAD(x)			0xFFFFFFFF
+#define	do_bdinfo(a,b,c,d)
+
+
+/*
+ * CPU type
+ * 
+ * CONFIG_7xx			- We have a 750 or 755 CPU
+ * CONFIG_74xx			- We have a 7400 CPU
+ * CONFIG_ALTIVEC		- We have altivec enabled CPU (only 7400)
+ * CONFIG_BUS_CLK		- System bus clock in Hz
+ */
+
+#define	CONFIG_7xx
+#undef	CONFIG_74xx
+#undef	CONFIG_ALTIVEC
+#define CONFIG_BUS_CLK			66000000
+
+
+/*
+ * Monitor configuration
+ * 
+ * CONFIG_COMMANDS		- List of command sets to include in shell
+ * 
+ * The following command sets have been tested and known to work:
+ * 
+ * CFG_CMD_CACHE		- Cache control commands
+ * CFG_CMD_MEMORY		- Memory display, change and test commands
+ * CFG_CMD_FLASH		- Erase and program flash
+ * CFG_CMD_ENV			- Environment commands
+ * CFG_CMD_RUN			- Run commands stored in env vars
+ * CFG_CMD_ELF			- Load ELF files
+ * CFG_CMD_NET			- Networking/file download commands
+ * CFG_CMD_PING			- ICMP Echo Request command
+ * CFG_CMD_PCI			- PCI Bus scanning command
+ */
+
+#define CONFIG_COMMANDS		( (CFG_CMD_DFL & ~(CFG_CMD_KGDB)) |	\
+						   CFG_CMD_FLASH |	\
+						   CFG_CMD_ENV |	\
+						   CFG_CMD_RUN |	\
+						   CFG_CMD_ELF |	\
+						   CFG_CMD_NET |	\
+						   CFG_CMD_PING |	\
+						   CFG_CMD_PCI)
+
+
+/*
+ * Serial configuration
+ *
+ * CONFIG_CONS_INDEX		- Serial console port number (COM1)
+ * CONFIG_BAUDRATE			- Serial speed
+ */
+
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			9600
+
+
+/*
+ * PCI config
+ * 
+ * CONFIG_PCI				- Enable PCI bus
+ * CONFIG_PCI_PNP			- Enable Plug & Play support
+ * CONFIG_PCI_SCAN_SHOW		- Enable display of devices at startup
+ */
+
+#define	CONFIG_PCI
+#define	CONFIG_PCI_PNP
+#undef	CONFIG_PCI_SCAN_SHOW
+
+
+/*
+ * Network config
+ * 
+ * CONFIG_NET_MULTI			- Support for multiple network interfaces
+ * CONFIG_EEPRO100			- Intel 8255x Ethernet Controller
+ * CONFIG_EEPRO100_SROM_WRITE - Enable writing to network card ROM
+ */
+
+#define	CONFIG_NET_MULTI
+#define	CONFIG_EEPRO100
+#define	CONFIG_EEPRO100_SROM_WRITE
+
+
+/*
+ * Enable extra init functions
+ * 
+ * CONFIG_MISC_INIT_F		- Call pre-relocation init functions
+ * CONFIG_MISC_INIT_R		- Call post relocation init functions
+ */
+
+#undef	CONFIG_MISC_INIT_F
+#define CONFIG_MISC_INIT_R 
+
+
+/*
+ * Boot config
+ * 
+ * CONFIG_BOOTCOMMAND		- Command(s) to execute to auto-boot
+ * CONFIG_BOOTDELAY			- How long to wait before auto-boot (in sec)
+ */
+
+#define CONFIG_BOOTCOMMAND		\
+	"bootp;" \
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
+	"bootm"
+#define CONFIG_BOOTDELAY		5
+
+
+/*===================================================================
+ * 
+ * Board configuration settings - You should not need to modify these
+ * 
+ *===================================================================
+ */
+
+
+#include <cmd_confdefs.h>
+
+
+/*
+ * Memory map
+ * 
+ * This board runs in a standard CHRP (Map-B) configuration.
+ * 
+ *	Type		Start		End			Size	Width	Chip Sel
+ *	----------- ----------- ----------- ------- ------- --------
+ *	SDRAM		0x00000000	0x04000000	64MB	64b		SDRAMCS0
+ *	User LED's	0x78000000						RCS3
+ *	UART		0x7C000000						RCS2
+ *	Mailbox		0xFF000000						RCS1
+ *	Flash		0xFFC00000	0xFFFFFFFF	4MB	64b		RCS0
+ * 
+ * Flash sectors are laid out as follows.
+ * 
+ *	Sector	Start		End			Size	Comments
+ *	------- ----------- ----------- ------- -----------
+ *	 0		0xFFC00000	0xFFC3FFFF	256KB
+ *   1		0xFFC40000	0xFFC7FFFF	256KB
+ *	 2		0xFFC80000	0xFFCBFFFF	256KB
+ *	 3		0xFFCC0000	0xFFCFFFFF	256KB
+ *	 4		0xFFD00000	0xFFD3FFFF	256KB
+ *	 5		0xFFD40000	0xFFD7FFFF	256KB
+ *	 6		0xFFD80000	0xFFDBFFFF	256KB
+ *	 7		0xFFDC0000	0xFFDFFFFF	256KB
+ *   8		0xFFE00000	0xFFE3FFFF	256KB
+ *	 9		0xFFE40000	0xFFE7FFFF	256KB
+ *  10		0xFFE80000	0xFFEBFFFF	256KB
+ *  11		0xFFEC0000	0xFFEFFFFF	256KB
+ *  12		0xFFF00000	0xFFF3FFFF	256KB	U-Boot code here
+ *  13		0xFFF40000	0xFFF7FFFF	256KB
+ *  14		0xFFF80000	0xFFFBFFFF	256KB
+ *  15		0xFFFC0000	0xFFFDFFFF	128KB
+ *  16		0xFFFE0000	0xFFFE7FFF	 32KB	U-Boot env vars here
+ *  17		0xFFFE8000	0xFFFEFFFF	 32KB	U-Boot backup copy of env vars here
+ *  18		0xFFFF0000	0xFFFFFFFF	 64KB
+ */
+
+
+/*
+ * SDRAM config - see memory map details above.
+ * 
+ * CFG_SDRAM_BASE			- Start address of SDRAM, this _must_ be zero!
+ * CFG_SDRAM_SIZE			- Total size of contiguous SDRAM bank(s)
+ */
+
+#define CFG_SDRAM_BASE			0x00000000
+#define CFG_SDRAM_SIZE			0x04000000
+
+
+/* 
+ * Flash config - see memory map details above.
+ * 
+ * CFG_FLASH_BASE			- Start address of flash memory
+ * CFG_FLASH_SIZE			- Total size of contiguous flash mem
+ * CFG_FLASH_ERASE_TOUT		- Erase timeout in ms
+ * CFG_FLASH_WRITE_TOUT		- Write timeout in ms
+ * CFG_MAX_FLASH_BANKS		- Number of banks of flash on board
+ * CFG_MAX_FLASH_SECT		- Number of sectors in a bank
+ */
+
+#define CFG_FLASH_BASE			0xFFC00000
+#define CFG_FLASH_SIZE			0x00400000
+#define CFG_FLASH_ERASE_TOUT	250000
+#define CFG_FLASH_WRITE_TOUT	5000
+#define CFG_MAX_FLASH_BANKS		1
+#define CFG_MAX_FLASH_SECT		19
+
+
+/*
+ * Monitor config - see memory map details above
+ * 
+ * CFG_MONITOR_BASE			- Base address of monitor code
+ * CFG_MALLOC_LEN			- Size of malloc pool (128KB)
+ */
+
+#define CFG_MONITOR_BASE		TEXT_BASE
+#define CFG_MALLOC_LEN			0x20000
+
+
+/*
+ * Command shell settings
+ * 
+ * CFG_BARGSIZE			- Boot Argument buffer size
+ * CFG_BOOTMAPSZ		- Size of app's mapped RAM at boot (Linux=8MB)
+ * CFG_CBSIZE			- Console Buffer (input) size
+ * CFG_LOAD_ADDR		- Default load address
+ * CFG_LONGHELP			- Provide more detailed help
+ * CFG_MAXARGS			- Number of args accepted by monitor commands
+ * CFG_MEMTEST_START		- Start address of test to run on RAM
+ * CFG_MEMTEST_END		- End address of RAM test
+ * CFG_PBSIZE			- Print Buffer (output) size
+ * CFG_PROMPT			- Prompt string
+ */
+
+#define CFG_BARGSIZE			1024
+#define CFG_BOOTMAPSZ			0x800000
+#define CFG_CBSIZE			1024
+#define CFG_LOAD_ADDR			0x100000
+#define CFG_LONGHELP
+#define CFG_MAXARGS			16
+#define CFG_MEMTEST_START		0x00040000
+#define CFG_MEMTEST_END			0x00040100
+#define CFG_PBSIZE			1024
+#define CFG_PROMPT			"=> "
+
+
+/*
+ * Environment config - see memory map details above
+ * 
+ * CFG_ENV_IS_IN_FLASH		- The env variables are stored in flash
+ * CFG_ENV_ADDR			- Address of the sector containing env vars
+ * CFG_ENV_SIZE			- Ammount of RAM for env vars (used to save RAM, 4KB) 
+ * CFG_ENV_SECT_SIZE		- Size of sector containing env vars (32KB)
+ */
+
+#define CFG_ENV_IS_IN_FLASH		1
+#define CFG_ENV_ADDR			0xFFFE0000
+#define CFG_ENV_SIZE			0x1000
+#define CFG_ENV_ADDR_REDUND		0xFFFE8000
+#define CFG_ENV_SIZE_REDUND		0x1000
+#define CFG_ENV_SECT_SIZE		0x8000
+
+
+/*
+ * Initial RAM config
+ *
+ * Since the main system RAM is initialised very early, we place the INIT_RAM
+ * in the main system RAM just above the exception vectors. The contents are
+ * copied to top of RAM by the init code.
+ * 
+ * CFG_INIT_RAM_ADDR		- Address of Init RAM, above exception vect
+ * CFG_INIT_RAM_END			- Size of Init RAM
+ * CFG_GBL_DATA_SIZE		- Ammount of RAM to reserve for global data
+ * CFG_GBL_DATA_OFFSET		- Start of global data, top of stack
+ */
+
+#define CFG_INIT_RAM_ADDR		(CFG_SDRAM_BASE + 0x4000)
+#define CFG_INIT_RAM_END		0x4000
+#define CFG_GBL_DATA_SIZE		128
+#define CFG_GBL_DATA_OFFSET		(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+
+/*
+ * Initial BAT config
+ * 
+ * BAT0	- System SDRAM
+ * BAT1 - LED's and Serial Port
+ * BAT2 - PCI Memory
+ * BAT3 - PCI I/O including Flash Memory
+ */
+
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+
+#define CFG_IBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+
+/*
+ * Cache config
+ * 
+ * CFG_CACHELINE_SIZE		- Size of a cache line (CPU specific)
+ * CFG_L2					- L2 cache enabled if defined
+ * L2_INIT					- L2 cache init flags
+ * L2_ENABLE				- L2 cache enable flags
+ */
+
+#define CFG_CACHELINE_SIZE		32
+#undef	CFG_L2
+#define L2_INIT					0
+#define L2_ENABLE				0
+
+
+/*
+ * Clocks config
+ * 
+ * CFG_BUS_HZ				- Bus clock frequency in Hz
+ * CFG_BUS_CLK				- As above (?)
+ * CFG_HZ					- Decrementer freq in Hz
+ */
+
+#define CFG_BUS_HZ				CONFIG_BUS_CLK
+#define CFG_BUS_CLK				CONFIG_BUS_CLK
+#define CFG_HZ					1000
+
+
+/*
+ * Serial port config
+ * 
+ * CFG_BAUDRATE_TABLE		- List of valid baud rates
+ * CFG_NS16550				- Include the NS16550 driver
+ * CFG_NS16550_SERIAL		- Include the serial (wrapper) driver
+ * CFG_NS16550_CLK			- Frequency of reference clock
+ * CFG_NS16550_REG_SIZE		- 64-bit accesses to 8-bit port
+ * CFG_NS16550_COM1			- Base address of 1st serial port
+ */
+
+#define CFG_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, 115200 }
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_CLK			3686400
+#define CFG_NS16550_REG_SIZE	-8
+#define CFG_NS16550_COM1		0x7C000000
+
+
+/*
+ * PCI Config - Address Map B (CHRP)
+ */
+
+#define CFG_PCI_MEMORY_BUS      0x00000000
+#define CFG_PCI_MEMORY_PHYS     0x00000000
+#define CFG_PCI_MEMORY_SIZE     0x40000000
+#define CFG_PCI_MEM_BUS         0x80000000
+#define CFG_PCI_MEM_PHYS        0x80000000
+#define CFG_PCI_MEM_SIZE        0x7D000000
+#define CFG_ISA_MEM_BUS         0x00000000
+#define CFG_ISA_MEM_PHYS        0xFD000000
+#define CFG_ISA_MEM_SIZE        0x01000000
+#define CFG_PCI_IO_BUS          0x00800000
+#define CFG_PCI_IO_PHYS         0xFE800000
+#define CFG_PCI_IO_SIZE         0x00400000
+#define CFG_ISA_IO_BUS          0x00000000
+#define CFG_ISA_IO_PHYS         0xFE000000
+#define CFG_ISA_IO_SIZE         0x00800000
+#define CFG_ISA_IO_BASE_ADDRESS CFG_ISA_IO_PHYS
+#define CFG_ISA_IO              CFG_ISA_IO_PHYS
+#define CFG_60X_PCI_IO_OFFSET   CFG_ISA_IO_PHYS
+
+
+/*
+ * Extra init functions
+ * 
+ * CFG_BOARD_ASM_INIT		- Call assembly init code
+ */
+
+#define CFG_BOARD_ASM_INIT
+
+
+/*
+ * Boot flags
+ * 
+ * BOOTFLAG_COLD			- Indicates a power-on boot
+ * BOOTFLAG_WARM			- Indicates a software reset
+ */
+ 
+#define BOOTFLAG_COLD			0x01
+#define BOOTFLAG_WARM			0x02
+
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
index 96cb6e4..9ebb51e 100644
--- a/include/configs/spieval.h
+++ b/include/configs/spieval.h
@@ -191,16 +191,6 @@
 
 #undef	CONFIG_BOOTARGS
 
-#if defined (CONFIG_TQM5200_AA)
-# define CONFIG_U_BOOT_SUFFIX	"-AA\0"
-#elif defined (CONFIG_TQM5200_AB)
-# define CONFIG_U_BOOT_SUFFIX	"-AB\0"
-#elif defined (CONFIG_TQM5200_AC)
-# define CONFIG_U_BOOT_SUFFIX	"-AC\0"
-#else
-# define CONFIG_U_BOOT_SUFFIX	"\0"
-#endif
-
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
@@ -217,7 +207,7 @@
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"bootfile=/tftpboot/tqm5200/uImage\0"				\
 	"load=tftp 200000 ${u-boot}\0"					\
-	"u-boot=/tftpboot/tqm5200/u-boot.bin"	CONFIG_U_BOOT_SUFFIX	\
+	"u-boot=/tftpboot/tqm5200/u-boot.bin\0"				\
 	"update=protect off FC000000 FC05FFFF;"				\
 		"erase FC000000 FC05FFFF;"				\
 		"cp.b 200000 FC000000 ${filesize};"			\
@@ -283,13 +273,6 @@
 #endif
 
 /* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB)
-#define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
-				CFG_I2C_SLAVE }
-#elif defined (CONFIG_TQM5200_AC)
-#define I2C_ADDR_LIST	{	CFG_I2C_SLAVE }
-#endif
-
 #if defined (CONFIG_MINIFAP)
 #undef I2C_ADDR_LIST
 #define I2C_ADDR_LIST	{	CFG_I2C_EEPROM_ADDR,	\
@@ -478,13 +461,9 @@
  * SRAM - Do not map below 2 GB in address space, because this area is used
  * for SDRAM autosizing.
  */
-#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define CFG_CS2_START		0xE5000000
-#ifdef CONFIG_TQM5200_AB
-#define CFG_CS2_SIZE		0x80000		/* 512 kByte */
-#else  /* CONFIG_CS_AUTOCONF */
 #define CFG_CS2_SIZE		0x100000	/* 1 MByte */
-#endif
 #define CFG_CS2_CFG		0x0004D930
 #endif
 
@@ -492,8 +471,7 @@
  * Grafic controller - Do not map below 2 GB in address space, because this
  * area is used for SDRAM autosizing.
  */
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
-    defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
 #define SM501_FB_BASE		0xE0000000
 #define CFG_CS1_START		(SM501_FB_BASE)
 #define CFG_CS1_SIZE		0x4000000	/* 64 MByte */
diff --git a/include/configs/trab.h b/include/configs/trab.h
index b6d4bcf..935aca2d 100644
--- a/include/configs/trab.h
+++ b/include/configs/trab.h
@@ -165,7 +165,6 @@
 				CFG_CMD_DATE			| \
 				CFG_CMD_DHCP			| \
 				CFG_CMD_FAT			| \
-				CFG_CMD_JFFS2			| \
 				CFG_CMD_NFS			| \
 				CFG_CMD_SNTP			| \
 				CFG_CMD_USB	)
@@ -179,7 +178,6 @@
 				CFG_CMD_DATE			| \
 				CFG_CMD_DHCP			| \
 				CFG_CMD_FAT			| \
-				CFG_CMD_JFFS2			| \
 				CFG_CMD_NFS			| \
 				CFG_CMD_SNTP			| \
 				CFG_CMD_USB	)
@@ -389,10 +387,10 @@
 #define MTDIDS_DEFAULT		"nor0=0"
 
 /* production flash layout */
-#define MTDPARTS_DEFAULT	"mtdparts=0:32k(Firmware1)ro,"		\
+#define MTDPARTS_DEFAULT	"mtdparts=0:16k(Firmware1)ro,"		\
 						"16k(Env1),"		\
 						"16k(Env2),"		\
-						"320k(Firmware2)ro,"	\
+						"336k(Firmware2)ro,"	\
 						"896k(Kernel),"		\
 						"5376k(Root-FS),"	\
 						"1408k(JFFS2),"		\
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
index c5ee78f..4e97b01 100644
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -47,6 +47,8 @@
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
 
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
 /*
  * Physical Memory Map
  */
@@ -94,7 +96,6 @@
 
 #define CONFIG_ENV_OVERWRITE
 
-#define CFG_JFFS_CUSTOM_PART	/* see board/voiceblue/jffs2parts.c */
 #endif
 
 /*
@@ -104,9 +105,11 @@
 #ifdef VOICEBLUE_SMALL_FLASH
 #define CFG_MALLOC_LEN		(SZ_64K - CFG_GBL_DATA_SIZE)
 #define CONFIG_STACKSIZE	SZ_8K
+#define PHYS_SDRAM_1_RESERVED	0
 #else
 #define CFG_MALLOC_LEN		SZ_4M
 #define CONFIG_STACKSIZE	SZ_1M
+#define PHYS_SDRAM_1_RESERVED	(CFG_MONITOR_LEN + CFG_MALLOC_LEN + CONFIG_STACKSIZE)
 #endif
 
 /*
@@ -174,6 +177,7 @@
 #define CONFIG_BOOTCOMMAND	"run nboot"
 #define CONFIG_PREBOOT		"run setup"
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"silent=1\0"						\
 	"ospart=0\0"						\
 	"swapos=no\0"						\
 	"setpart="						\
@@ -185,15 +189,37 @@
 	"fi\0"							\
 	"setup=setenv bootargs console=ttyS0,$baudrate "	\
 		"mtdparts=$mtdparts\0"				\
-	"nfsargs=run setpart; setenv bootargs $bootargs "	\
-		"root=/dev/nfs ip=dhcp\0"			\
+	"nfsargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
+		"nfsroot=$rootpath root=/dev/nfs\0"		\
 	"flashargs=run setpart; setenv bootargs $bootargs "	\
 		"root=/dev/mtdblock$partition ro "		\
 		"rootfstype=jffs2\0"				\
-	"nboot=run nfsargs; bootp; tftp; bootm\0"		\
-	"fboot=run flashargs; fsload /boot/uImage; bootm\0"
+	"initrdargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
+	"fboot=run flashargs; fsload /boot/uImage; bootm\0"	\
+	"iboot=bootp; run initrdargs; tftp; bootm\0"		\
+	"nboot=bootp; run nfsargs; tftp; bootm\0"
 #endif
 
+#ifndef VOICEBLUE_SMALL_FLASH
+#define CONFIG_SILENT_CONSOLE		1	/* enable silent startup */
+
+#if 1	/* feel free to disable for development */
+#define CONFIG_AUTOBOOT_KEYED		/* Enable password protection	*/
+#define CONFIG_AUTOBOOT_PROMPT	"\nVoiceBlue Enterprise - booting...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"."	/* 1st "password"	*/
+#endif
+
+/*
+ * JFFS2 partitions (mtdparts command line support)
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=omapflash.0"
+#define MTDPARTS_DEFAULT	"mtdparts=omapflash.0:128k(uboot),64k(env),64k(r_env),16256k(data1),-(data2)"
+
+#endif	/* VOICEBLUE_SMALL_FLASH */
+
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
@@ -213,7 +239,7 @@
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	PHYS_SDRAM_1
-#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE
+#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
 
 #undef	CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 
@@ -247,22 +273,4 @@
 
 #define VOICEBLUE_LED_REG	0x04030000
 
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00040000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT		"nor0=voiceblue-0"
-#define MTDPARTS_DEFAULT	"mtdparts=voiceblue-0:128k(uboot),64k(env),64k(renv),-(jffs2)"
-*/
-
 #endif	/* __CONFIG_H */